Ultrathin reduced graphene oxide/MOF nanofiltration membrane with improved purification performance at low pressure

Template-free efficacious morphology of electrosynthesized polyaniline/β-cyclodextrin host-guest complex on Au/rGO modified electrode for removal and recovery of rare-earth and heavy elements from seawater

Global water pollution and scarcity of water resources are turning increasingly into serious threats to the survival of all living organisms on Earth. This study offers an influent strategy for the electrosynthesis of reduced graphene oxide/polyaniline/β-cyclodextrin (rGO/PAni/βCD) nanocomposite and its application to the removal/recovery of heavy elements (HEs) and rare-earth elements (REEs). Besides physicochemical and electrochemical studies, the surface morphological and statistical properties of fabricated nanocomposite electrode were examined. The textural and morphological characteristics of nanocomposite electrode were investigated via AFM data based on statistical, stereometric, and fractal theory. The cohesive, porous, and well-developed morphology of fabricated nanocomposite electrode has enabled the electrodeposition technique to achieve significant simultaneous removal/recovery efficiency of HE and REE ions such as Pb(II), Cu(II), Cd(II), Hg(II), Ce(IV), and Nb(V). Therefore, using rGO/PAni/βCD, considerable removal of HEs and REEs was achieved under optimized pH, 0.1 M KNO3, and 35 mg L-1 metal ion initial concentration during 20 min. Removal capacity of the nanocomposite electrode is preserved subsequent to 10 cycles of electrodeposition/desorption, according to the desorption investigation through eluted adsorbent at time intervals in deionized water and adjusted acidic pH values. Then, using rGO/PAni/CD nanocomposite, simulated seawater remediation was accomplished successfully. This interdisciplinary approach reveals that the removal/recovery efficiency enhance linearly along with the improvement of well-developed morphology for electrosynthesized composites. Thus, these results suggest how the morphological features of the polymer composites could improve remediation of water resources.

Recent trends in wastewater treatment by using metal-organic frameworks (MOFs) and their composites: A critical view-point

Respecting the basic need of clean and safe water on earth for every individual, it is necessary to take auspicious steps for waste-water treatment. Recently, metal-organic frameworks (MOFs) are considered as promising material because of their intrinsic features including the porosity and high surface area. Further, structural tunability of MOFs by following the principles of reticular chemistry, the MOFs can be functionalized for the high adsorption performance as well as adsorptive removal of target materials. However, there are still some major concerns associated with MOFs limiting their commercialization as promising adsorbents for waste-water treatment. The cost, toxicity and regenerability are the major issues to be addressed for MOFs to get insightful results. In this article, we have concise the current strategies to enhance the adsorption capacity of MOFs during the water-treatment for the removal of toxic dyes, pharmaceuticals, and heavy metals. Further, we have also discussed the role of metallic nodes, linkers and associated functional groups for effective removal of toxic water pollutants. In addition to conformist overview, we have critically analyzed the MOFs as adsorbents in terms of toxicity, cost and regenerability. These factors are utmost important to address before commercialization of MOFs as adsorbents for water-treatment. Finally, some future perspectives are discussed to give directions for potential research.

Tailoring the performance of composite PEI nanofiltration membranes via incorporating activated cyclodextrins

Cyclodextrins (CDs) with unique cavity structures have been used as materials for nanofiltration membrane fabrications. In the present work, the activated CD (O-CD), oxidated by NaIO4, and polyethyleneimine (PEI) were co-deposited on a hydrolyzed polyacrylonitrile support, post-treated by glycerol protection and heating treatment, to prepare nanofiltration membranes with low molecular weight cut-off (MWCO). As the cavities in CD present and the aldehyde groups introduced after oxidation, the O-CDs were expected to crosslink the PEI layer and provide extra permeating channels. The filtration experiments showed that the incorporation of O-CDs improved the permeances of the O-CD-PEI/HPAN nanofiltration membranes. The performance can be tailored by the control of the loading or the oxidation degree of the O-CD. At optimal conditions, the permeance increment was nearly double (from 9.2 to 21.1 Lm-2·h-1·bar-1). While the selectivity was without significant sacrifice, the rejection of PEG 200 remained around 90%. Meanwhile, the membrane stability was demonstrated by pro-longed filtratiing a PEG 200 aqueous solution. The constant permeance and rejection confirmed the O-CD-PEI/HPAN membranes were stable. The incorporation of activated CD in PEI offers a facile strategy to promote the permeance of PEI-based membranes.

Performance Research of Natural Mica Modified with Zirconium-Based Metal-Organic Frameworks for an Epoxy Resin Anti-Corrosion Coating

A new composite material made from mica and a metal-organic framework (MOF) has been developed to improve the anticorrosive capabilities of epoxy resin coatings. The layered mica was loaded with denser and more uniform UIO-66 nanoparticles after modifying the composite with polyethyleneimine (PEI). The composites were used as fillers to prepare epoxy coatings that exhibited long-lasting active (labyrinth effect produced by mica) and passive (pH-sensitive release of corrosion inhibitors) corrosion protection. Settling experiments showed that polyethyleneimine improved the composites' compatibility in epoxy resin. After being immersed in a 3.5 wt.% NaCl solution for 60 days, the adhesion of PMC-UIO@MBT/EP increases to 9.01 MPa, while the water absorption rate only reaches 2.57%. It indicates that the coating has good barrier properties and stability. After being soaked in a 3.5 wt.% NaCl solution for 60 days at pH = 7, PMC-UIO@MBT/EP exhibits high low-frequency impedance (8.30 × 108 Ω), as demonstrated by the electronic impedance spectrum (EIS). In addition, the coating also exhibited the highest low-frequency impedance after 30 days in 3.5 wt.% NaCl solution at pH = 11.

Nanofiltration Membranes for the Removal of Heavy Metals from Aqueous Solutions: Preparations and Applications

Water shortages are one of the problems caused by global industrialization, with most wastewater discharged without proper treatment, leading to contamination and limited clean water supply. Therefore, it is important to identify alternative water sources because many concerns are directed toward sustainable water treatment processes. Nanofiltration membrane technology is a membrane integrated with nanoscale particle size and is a superior technique for heavy metal removal in the treatment of polluted water. The fabrication of nanofiltration membranes involves phase inversion and interfacial polymerization. This review provides a comprehensive outline of how nanoparticles can effectively enhance the fabrication, separation potential, and efficiency of NF membranes. Nanoparticles take the form of nanofillers, nanoembedded membranes, and nanocomposites to give multiple approaches to the enhancement of the NF membrane's performance. This could significantly improve selectivity, fouling resistance, water flux, porosity, roughness, and rejection. Nanofillers can form nanoembedded membranes and thin films through various processes such as in situ polymerization, layer-by-layer assembly, blending, coating, and embedding. We discussed the operational conditions, such as pH, temperature, concentration of the feed solution, and pressure. The mitigation strategies for fouling resistance are also highlighted. Recent developments in commercial nanofiltration membranes have also been highlighted.

A review on hybrid membrane-adsorption systems for intensified water and wastewater treatment: Process configurations, separation targets, and materials applied

In the era of rapid and conspicuous progress of water treatment technologies, combined adsorption and membrane filtration systems have gained great attention as a novel and efficient method for contaminant removal from aqueous phase. Further development of these techniques for water/wastewater treatment applications will be promising for the recovery of water resources as well as reducing the water tension throughout the world. This review introduces the state-of-the-art on the capabilities of the combined adsorption-membrane filtration systems for water and wastewater treatment applications. Technical information including employed materials, superiorities, operational limitations, process sustainability and upgradeing strategies for two general configurations i.e. hybrid (pre-adsorption and post-adsorption) and integrated (film adsorbents, low pressure membrane-adsorption coupling and membrane-adsorption bioreactors) systems has been surveyed and presented. Having a systematic look at the fundamentals of hybridization/integration of the two well-established and efficient separation methods as well as spotlighting the current status and prospectives of the combination strategies, this work will be valuable to all the interested researchers working on design and development of cutting-edge wastewater/water treatment techniques. This review also draws a clear roadmap for either decision making and choosing the best alternative for a specific target in water treatment or making a plan for further enhancement and scale-up of an available strategy.

Double-charged self-assembled rGO/g-C3N4 membrane prepared by "functional group substitution" for heavy metal ions rejection at low pressure

Heavy metals are still the critical pollutants in industrial wastewater and there is an urgent need for efficient and environmentally friendly treatment technologies. Reduced graphene oxide (rGO) is widely used for preparations of nanofiltration (NF) membranes but suffers from poor hydrophilicity and electronegativity. In this work, a double-charged rGO/g-C₃N₄-P membrane was prepared for removal of heavy metals at low pressure. Graphitic carbon nitride (g-C₃N₄) assisted reduction of GO membranes under ultraviolet (UV) irradiation, and the modification of functional groups with high polarity improved the hydrophilicity of membrane surface. The filtration performance for heavy metals of rGO/g-C₃N₄-P membrane was evaluated under low pressure (1-2 bar). The rejection rates of Cu²⁺, Cr³⁺, Mn²⁺, Cd²⁺, and Pb²⁺ by membranes reduced by UV for 18 h (rGO/g-C₃N₄-18-P membrane) reached 94.72 %, 98.05 %, 82.32 %, 88.2 % and 77.15 %, respectively. In the experiment of mixed simulated wastewater, the rejection rates of NO₃^- and SO₄^2- both reached >95 %. Outstanding rejection rates were attributed to the interaction and the synergy effect of double-charged layers as well as steric effects. Meanwhile, the water flux of rGO/g-C₃N₄-18-P membrane was as high as 37.14-50.16 L m^-2h^-1bar^-1 (1-2 bar). The high flux was due to the reduced degree of oxidation so that water molecules transported between GO nanochannels more smoothly and the transport path was shortened through the nanopores of g-C₃N₄. Obviously, flux and heavy metal rejection of rGO/g-C₃N₄-18-P membrane were simultaneously improved, breaking "trade-off" effect. Furthermore, rGO/g-C₃N₄-18-P membrane showed excellent antifouling ability and the potential for heavy metal wastewater filtration in comparison with other NF membranes reported in literature.

Overview on recent advances of magnetic metal-organic framework (MMOF) composites in removal of heavy metals from aqueous system

Developing a novel, simple, and cost-effective analytical technique with high enrichment capacity and selectivity is crucial for environmental monitoring and remediation. Metal-organic frameworks (MOFs) are porous coordination polymers that are self-assembly synthesized from organic linkers and inorganic metal ions/metal clusters. Magnetic metal-organic framework (MMOF) composites are promising candidate among the new-generation sorbent materials available for magnetic solid-phase extraction (MSPE) of environmental contaminants due to their superparamagnetism properties, high crystallinity, permanent porosity, ultrahigh specific surface area, adaptable pore shape/sizes, tunable functionality, designable framework topology, rapid and ultrahigh adsorption capacity, and reusability. In this review, we focus on recent scientific progress in the removal of heavy metal ions present in contaminated aquatic system by using MMOF composites. Different types of MMOFs, their synthetic approaches, and various properties that are harnessed for removal of heavy metal ions from contaminated water are discussed briefly. Adsorption mechanisms involved, adsorption capacity, and regeneration of the MMOF sorbents as well as recovery of heavy metal ions adsorbed that are reported in the last ten years have been discussed in this review. Moreover, particular prospects, challenges, and opportunities in future development of MMOFs towards their greener synthetic approaches for their practical industrial applications have critically been considered in this review.

Zwitterionic metal-organic frameworks modified polyamide membranes with enhanced water flux and antifouling capacity

Antifouling properties are considered to be crucial parameter to polyamide (PA) composite nanofiltration (NF) membranes for practical applications. In this study, an antifouling material, surface zwitterionization of Metal-organic frameworks (Z-MIL-101 (Cr)) was firstly prepared by decorating zwitterionic polymer onto the MOFs surface. Subsequently, a novel type of MOFs-based hybrid membranes were fabricated via mixing the Z-MIL-101 (Cr) nanoparticle with the organic matrix by interfacial polymerization technique. The most optimal hybrid membrane had a high water permeation of 26 L m^-2 h^-1 bar^-1, which was 2.1 times higher than that pristine PA membrane, while the retention for Na₂SO₄ was still kept at a considerably high value of 93%. The significant increased water flue can attribute to the existence of water channels generated by the Z-MIL-101 (Cr). More important, the antifouling property of the hybrid membrane was much better than that pristine PA, which was due to the formation of superhydrophilic liquid layer surrounding the zwitterionic groups. The combination of the micropore structure of the MOFs and the excellent antifouling properties of the decorated zwitterionic polymer effectively improved separation performances and antifouling ability, which makes these hybrid membranes promising for water purification.

Ganzoury M, Zhang N, de Lannoy CF. Nanocomposite Polymeric Membranes for Organic Micropollutant Removal: A Critical Review

The prevalence of organic micropollutants (OMPs) and their persistence in water supplies have raised serious concerns for drinking water safety and public health. Conventional water treatment technologies, including adsorption and biological treatment, are known to be insufficient in treating OMPs and have demonstrated poor selectivity toward a wide range of OMPs. Pressure-driven membrane filtration has the potential to remove many OMPs detected in water with high selectivity as a membrane's molecular weight cutoff (MWCO), surface charge, and hydrophilicity can be easily tailored to a targeted OMP's size, charge and octanol-water partition coefficient (Kow). Over the past 10 years, polymeric (nano)composite microfiltration (MF), ultrafiltration (UF), and nanofiltration (NF) membranes have been extensively synthesized and studied for their ability to remove OMPs. This review discusses the fate and transport of emerging OMPs in water, an assessment of conventional membrane-based technologies (NF, reverse osmosis (RO), forward osmosis (FO), membrane distillation (MD) and UF membrane-based hybrid processes) for their removal, and a comparison to the state-of-the-art nanoenabled membranes with enhanced selectivity toward specific OMPs in water. Nanoenabled membranes for OMP treatment are further discussed with respect to their permeabilities, enhanced properties, limitations, and future improvements.

Advances in metal-organic framework-based membranes

Membrane-based separations have garnered considerable attention owing to their high energy efficiency, low capital cost, small carbon footprint, and continuous operation mode. As a class of highly porous crystalline materials with well-defined pore systems and rich chemical functionalities, metal-organic frameworks (MOFs) have demonstrated great potential as promising membrane materials over the past few years. Different types of MOF-based membranes, including polycrystalline membranes, mixed matrix membranes (MMMs), and nanosheet-based membranes, have been developed for diversified applications with remarkable separation performances. In this comprehensive review, we first discuss the general classification of membranes and outline the historical development of MOF-based membranes. Subsequently, particular attention is devoted to design strategies for MOF-based membranes, along with detailed discussions on the latest advances on these membranes for various gas and liquid separation processes. Finally, challenges and future opportunities for the industrial implementation of these membranes are identified and outlined with the intent of providing insightful guidance on the design and fabrication of high-performance membranes in the future.

Highly Permeable Sulfonated Graphene-Based Composite Membranes for Electrochemically Enhanced Nanofiltration

A sulfophenyl-functionalized reduced graphene oxide (SrGO) membrane is prepared. The SrGO membranes have a high charge density in water and could provide many atomically smooth nanochannels, because of their strong ionized-SO3H groups and low oxygen content. Therefore, the SrGO membranes have an excellent performance in terms of high permeance and high rejection ability. The permeance of SrGO membranes could be up to 118.2 L m−2 h−1 bar−1, which is 7.6 times higher than that of GO membrane (15.5 L m−2 h−1 bar−1). Benefiting from their good electrical conductivity, the SrGO membranes could also function as an electrode and demonstrate a significantly increased rejection toward negatively charged molecules and positively charged heavy metal ions such as Cu2+, Cr3+ and Cd2+, if given an appropriate negative potential. The rejection ratios of these metal ions can be increased from <20% at 0 V to >99% at 2.0 V. This is attributed to the enhanced electrostatic repulsion between the SrGO membrane and the like-charged molecules, and the increased electrostatic adsorption and electrochemical reduction in these heavy metal ions on the membranes. This study is expected to contribute to efficient water treatment and the advance of graphene-based membranes.

High Flux and Antifouling Nanofiltration Membrane Modified by Ag@UiO-66-NH2 and Its Application for Biphenol A Removal

Owing to the specific porous structure which could provide additional passage channel for some molecules, metal organic frameworks are attractive candidates for enhancing permeability and selectivity of membranes in pervaporation, reverse osmosis, and gas separation. In this experiment, Ag@UiO-66-NH2 was introduced into polyamide separation layer by interfacial polymerization of triethylenetetramine and 1,3,5-benzenetricarboxylic acid chloride for nanofiltration. The results indicated that Ag@UiO-66-NH2 nanoparticles did endow the membranes with rapid diffusion pathways for water molecules. When the content of Ag@UiO-66-NH2 was 0.03 g, the prepared membrane (NF-Ag-3) showed high flux about 47.3 L·m-2·h-1 at 0.6 MPa, which is about 2-fold higher than that of polyamide membrane without Ag@UiO-66-NH2, while the MgSO4 rejection rate remained about 87.4%. The membrane also showed excellent antifouling properties, and the water flux recovery ratio was 95.6% after filtration BSA solution. When it was applied for 50 mg/L bisphenol A removal, the rejection rate reached 94.6%, and the flux is about 49.1 L·m-2·h-1. Moreover, Ag particles on UiO-66-NH2 rendered the membrane with good inhibition for Escherichia coli. The antibacterial rate of the membranes is above 95% when the loading of Ag@UiO-66-NH2 is more than 0.03 g.

Recent advances in metal-organic framework membranes for water treatment: A review

Among many separation membranes reported to date, the favorable polymer affinity and unique physio-chemical performances of metal-organic frameworks (MOFs) including ultra-high surface area, regular and highly controlled porosity have drawn widespread attention in industrial and academic communities. In this comprehensive review, the developmental timeline of MOF containing membranes for water treatment were clarified. The removal efficiencies, elimination mechanisms, as well as possible influencing factors of various MOF containing membranes that applied to water treatment were systematically summarized. The excellent removal performances of MOF containing membranes for various pollutants were determined by the size-exclusion, π-π stacking interaction, electrostatic interaction, hydrogen bonding and so on. Since the progress of engineered MOF containing membranes for practical wastewater treatment applications lags, we further analyzed the potential environmental application of MOF containing membranes from four aspects (stability of MOFs, antifouling performance of membranes, compatibility between MOF fillers and polymer matrix, dispersity of MOF nanoparticles in matrix), hoping to provide some meaningful insights.

Efficient removal of anionic, cationic textile dyes and salt mixture using a novel CS/MIL-100 (Fe) based nanofiltration membrane

The purification of hazardous textile dyeing wastewater has exhibited many challenges because it consists of a complex mixture, including dyestuff, additives, and salts. It is necessary to fabricate membranes with enhanced permeability, fouling resistance, stability, and superior dyes and salts removal from wastewater. Incorporating a highly water stable metal-organic framework (MOFs) into membranes would meet the requirements for the efficient purification of textile wastewater. In this study, nanofiltration (NF) membranes are fabricated by incorporating MIL-100 (Fe) into the chitosan (CS) through film casting technique. The effect of MIL-100 (Fe) loadings on chitosan characterized by FT-IR, XRD, contact angle measurement, FESEM-EDS, XPS, zeta potential, and surface roughness analysis. The membrane characterization confirmed the enhanced surface roughness, pore size, surface charge, and hydrophilicity. The CS/MIL-100 (Fe) membrane exhibited an improved pure water flux from 5 to 52 L/m²h as well as 99% rejection efficiency for cationic methylene blue (MB) and anionic methyl orange (MO). We obtained the rejection efficiency trend for the MB mixed salts in the order of MgSO₄ (Mg²⁺ - 51.6%, SO₄^2- - 52.5%) > Na₂SO₄ (Na⁺ - 26.3%, SO₄^2- - 29.3%) > CaCl₂ (Ca²⁺ - 21.4%, Cl^- - 23.8%) > NaCl (Na⁺ - 16.8%, Cl^- - 19.2%). In addition, the CS/MIL-100 (Fe) composite membrane showed excellent rejection efficiency and antifouling performances with high recycling stability. These stunning results evidenced that the CS/MIL-100 (Fe) nanofiltration membrane is a promising candidate for removing toxic pollutants in the textile dyeing wastewater.

Functional GO-based membranes for water treatment and desalination: Fabrication methods, performance and advantages. A review

Graphene oxide (GO) and GO-based materials have gained a significant interest in the membrane synthesis and functionalization sector in the recent years. Inspired by their unique and tuneable properties, several GO-based nanomaterials have been investigated and utilized as effective nanofillers for various membranes in the water treatment, purification and desalination sectors. This paper comprehensively reviews the recent advances of GO utilization in pressure, concentration and thermal-driven membrane processes. A brief overview on GO particles, properties, synthesis and functionalization methods was provided. The conventional and the state-of-art fabrication methods of GO-based membranes were summarized and discussed, and consequently the GO-based membranes were classified into different categories. The applications, types, and the performance in terms of flux and rejection were summarized and reviewed. The advantages of GO-based membranes in terms of antifouling properties, bactericidal effects, mechanical strength and stability have been reviewed, too. The review gives insights on the future perspectives of GO functional materials and their potential use in the various membrane processes discussed herein.

Thin-film nanocomposite NF membrane with GO on macroporous hollow fiber ceramic substrate for efficient heavy metals removal

The ceramic membrane has been widely used in the wastewater treatment based on the chemical resistance and superior separation performance. A robust and defect-free thin-film nanocomposite (TFN) nanofiltration (NF) membrane on the macroporous hollow fiber ceramic (HFC) substrate was novelly developed for heavy metals removal. Before interfacial polymerization (IP), the aqueous solution of graphene oxide (GO) grafted with ethylenediamine (EDA) was deposited on the HFC substrate by vacuum filtration. Then, a thin polyamide (PA) film was fabricated by EDA and 1,3,5-trimesoyl chloride (TMC), followed by heat treatment. The effects of GO content and EDA concentration on the performance of the NF membrane have been systematically investigated. The results showed that when the GO content was 0.015 mg·mL^-1 and the EDA concentration was 0.75 wt.%, the as-prepared eGO₃/PA-HFC membrane had a rejection rate of 94.12% for MgCl₂ and a pure water flux of 18.03 L·m^-2·h^-1. Additionally, the removal ability of eGO₃/PA-HFC membranes for heavy metal ions was satisfactory (93.33%, 92.73%, 90.45% and 88.35% for Zn²⁺, Cu²⁺, Ni²⁺ and Pb²⁺, respectively). The study explored further that it was efficient and stable for heavy metal ions removal during 30 h in the simulated tap water and mining wastewater, which indicated that the eGO/PA-HFC membrane has great application potential in wastewater treatment.

A novel water-stable two-dimensional zeolitic imidazolate frameworks thin-film composite membrane for enhancements in water permeability and nanofiltration performance

Polymer membranes for water treatment are constrained by the permeability-separation trade-off. Herein, two-dimensional (2D) zeolitic imidazolate frameworks (ZIFs) made of benzimidazole interconnected with Zn ions are used to create 2D Zn₂(Bim)₄ molecular sieve nanosheets, which is explored as an asymmetric, thin-film composite (TFC) nanofiltration (NF) membrane for removing organic dyes and salts from water with a high water permeability under a low operating pressure (1 bar). The 2D Zn₂(Bim)₄ TFC NF membrane is synthesized via ionic bonds between polycations and the peripheral hydroxy groups of 2D Zn₂(Bim)₄ nanosheets, regulating the assembly of 2D Zn₂(Bim)₄ to create a novel crack-free functional layer on top of a polyvinylidene fluoride (PVDF) ultrafiltration membrane. FESEM and XPS confirmed the presence of a polycations-regulated ultrathin functional layer with a thickness of ∼37 nm on the PVDF support. Benefiting from its structural feature, our 2D Zn₂(Bim)₄ TFC NF membrane could achieve an ultra-high flux of ∼290 L/(m²·h·bar) (5-10-fold higher than that of graphene-based membranes), good anti-fouling properties and high rejection rates (above 98%) for organic dyes. Moreover, the desalinization rate is 50-75%. That is, our membrane is endowed with NF capability, and its intrinsic ultrafiltration features (high water permeance, ultrafast, and energy-saving) are also well maintained.

Layer-by-layer assembly of bio-inspired borate/graphene oxide membranes for dye removal

Dye wastewater is harmful to the ecological environment because of its potential biological toxicity, teratogenicity, carcinogenicity, and mutagenicity. We fabricated a layered graphene oxide (GO) membrane through layer-by-layer (LBL) self-assembly. We used borate to crosslink with GO on a polyethyleneimine (PEI)-coated hydrolyzed polyacrylonitrile (hPAN) support. Fourier transform infrared (FTIR) spectrometry, Raman spectra, and x-ray photoelectron spectroscopy (XPS) confirmed the presence of a crosslinking reaction. The dynamic thermomechanical analysis (DMA) results indicated that the introduction of borate can significantly improve the mechanical properties of the membrane. The Young's modulus, ultimate tensile strength, and proportional limit of borate that was assembled twice as the outermost layer were increased by 110.81%, 62.37%, and 53.72%, respectively, as compared to those of a single-layered GO membrane. Moreover, the pure water fluxes of the layered GO membrane did not obviously decrease with an increase in the number of layers. The flux of the membrane with an outermost layer of borate was greater than that of the previous GO layer. The salt and dye rejection of the membranes was augmented with an increase in the number of layers. For the GO membrane assembled three times, rejection to methyl orange (MO), methylene blue (MB), NaCl, MgCl_2, and MgSO₄ reached 74.02%, 88.56%, 14.55%, 27.50%, and 41.95%, respectively. The use of borate as an inorganic crosslinker can avoid the environmental pollution caused by organic agents, and improve the mechanical properties as well as the filter capability of the layered GO membrane. Therefore, this study presents a novel method of membrane preparation for dye removal.

Modified-MOF-808-Loaded Polyacrylonitrile Membrane for Highly Efficient, Simultaneous Emulsion Separation and Heavy Metal Ion Removal

Oily wastewater, often containing heavy metal ions, is a common source of water pollution. In this study, a modified-MOF-loaded polyacrylonitrile membrane was designed and prepared via solvothermal reaction and electrospinning to simultaneously separate oil-in-water emulsions and adsorb heavy metal ions. The membrane shows superhydrophilicity and superoleophilicity in air and underwater superoleophobicity, which enables the membrane to efficiently separate various oil-in-water emulsions. The strong adsorption capacity of MOF-808 allows this membrane to adsorb heavy metal ions at various concentrations in a short time. The separation efficiency reached 99.97%, and the highest removal efficiency of heavy metal ions reached 97.7%. Additionally, the membrane demonstrated excellent recyclability and corrosion resistance. Overall, the membrane is highly efficient in treating wastewater, and it has great potential for practical applications.

A nanocomposite paper comprising calcium silicate hydrate nanosheets and cellulose nanofibers for high-performance water purification

Removal of soluble organic and inorganic contaminants from wastewater to produce clean water has received much attention recently. However, the simultaneous enhancement of water permeability and removal efficiency is still a challenge for filtration membranes. Here, we present a new kind of nanocomposite paper (CSH/CNF) consisting of calcium silicate hydrate (CSH) nanosheets and cellulose nanofibers (CNFs), and demonstrate the rapid water filtration and highly efficient contaminant (e.g., dyes, proteins, and metal ions) adsorption properties. The CNFs can serve as the bridging material to connect the CSH nanosheets to form a porous network structure and vital channels in the CSH/CNF paper for rapid water transportation. The weight ratio of CSH nanosheets in the paper is up to 75–85%. The weight ratio of CSH nanosheets has a significant effect on the water permeability and removal efficiency. The water permeability of the CSH/CNF paper with 82.5 wt% CSH nanosheets reaches as high as 312.7 L m⁻² h⁻¹ bar⁻¹, which is about 14.7 times that of the CSH/CNF paper with 75 wt% CSH nanosheets. Because of the high specific surface area and abundant adsorption sites of CSH nanosheets, the CSH/CNF paper with 82.5 wt% CSH nanosheets exhibits high adsorption capacities and removal efficiencies for methyl blue (242.6 mg g⁻¹, 97.3%), bovine serum albumin (289.2 mg g⁻¹, 98.5%) and Pb²⁺ ions (366.2 mg g⁻¹, 98.2%). The CSH/CNF nanocomposite paper holds great potential for application in environmental wastewater purification.

A nanocomposite paper with high water permeability and removal efficiency was prepared for the removal of organic and inorganic contaminants by filtration.

Impacts of mono/divalent cations on the lamellar structure of cross-linked GO layers and membrane filtration performance for different DOM fractions

This study evaluated the effects of co-existing cations (Na⁺ or Ca²⁺) on the lamellar structure of cross-linked graphene oxide (GO) layers and GO modified membrane performance in terms of their fouling behaviours and retention for single-model organic matter, namely, bull serum albumin (BSA), sodium alginate (SA), humic acid (HA) and tannic acid (TA). In the absence of co-existing cations, the GO layers mitigated membrane fouling for large molecules (SA, BSA, and HA) but led to severer pore blocking for small molecules (TA) compared with pristine membrane. Na⁺ and Ca²⁺ altered the performance impacts of the GO modified membrane due to different interactions with the cross-linked GO layers. Low concentrations of Na⁺ (<0.4 mM) enlarged interlayer spacing of the GO layers and caused a decrease in flux after physical cleaning, but the GO layers maintained the uniform lamellar structure. High concentrations of Na⁺ (>0.4 mM) promoted the aggregation of cross-linked GO layers through charge shielding and reduced the uniformity of lamellar structure, which weakened the antifouling performance for large molecules and promoted the passage of small molecules through the membrane. However, Ca²⁺ complexed with GO sheets and reinforced the uniform lamellar structure of the GO layers, leading to a better antifouling performance for the filtration of large molecules than the pristine membrane but aggravated TA fouling.

Modulation of cation trans-membrane transport in GO-MoS2 membranes through simultaneous control of interlayer spacing and ion-nanochannel interactions

The interlayer spacing and ion-nanochannel interactions of graphene oxide membranes (GOMs) were simultaneously modulated by thermal reduction and mixing with MoS₂ flakes for realizing selective ion separation, which was evaluated by the ratio of ion trans-membrane penetration rates (IPR). The results showed that the ratio of IPR_Cu2+ to IPR_Na+ increased to 1.90 in GOM after thermal reduction for 5 h, which was ∼9.56 times higher than that without thermal reduction, indicating the increase of selectivity of Cu²⁺ over Na⁺. This was because the reduction of oxygen-containing groups narrowed the interlayer spacing and moderated the coordination between Cu²⁺ and sp³ clusters in GO, leading to an enhancement of the size-sieving effect but a decrease in the Cu (II)-nanochannel interaction. Meanwhile, the value of IPR_Cu2+/IPR _Na+ was 0.374 after intercalating MoS₂ into GO laminates (GO-MoS₂ membrane, GMM), which was ∼1.87 times higher in comparison with that in GOM. This might be because the intercalation of MoS₂ narrowed the interlayer spacing, enhanced the size-sieving effect, and strengthened the Na⁺ ion-nanochannel interactions (cation-π and ion-MoS₂ chemical interactions) according to density functional theory calculations. Furthermore, IPR_Cu2+/IPR _Na+ was ∼5.09 in GMM under thermal reduction for 5 h, which was ∼25.5 times higher in comparison with that in GOM without thermal reduction, exhibiting a great enhancement in selectivity for Cu²⁺. This indicated that thermal reduction and MoS₂ intercalation could work in concert to control the size-sieving effect and ion-nanochannel interactions to achieve fine separation of heavy metal ions from main group metal ions.

A polyether amine modified metal organic framework enhanced the CO2 adsorption capacity of room temperature porous liquids

A room-temperature MOF-based porous liquid was prepared and showed an outstanding CO₂ uptake capacity.