Hierarchal growth of MoS2@CNT heterostructure for all solid state symmetric supercapacitor: Insights into the surface science and storage mechanism

Advanced flexible supercapacitors: vertical 2D MoS2 and WS2 nanowalls on graphenated carbon nanotube cotton

Flexible supercapacitors (SCs), which are mostly produced from carbon-based materials, are emerging devices for lightweight, portable, miniaturized, and wearable electronic products. However, it is important to improve the energy density, power density and durability of flexible SCs, for which newly developed materials and composites are required. In this study, we developed flexible SCs with enhanced capacitance and stability using the advantages of high volume/surface ratio of vertical two-dimensional MoS2 and WS2 structures. Electrodes were grown on graphenated carbon nanotube (G-CNT) cotton using Radio Frequency (RF) magnetron sputtering in a time varying manner to investigate the impact on the vertical structure densities on the performance of the as-developed SCs. Galvanostatic charge-discharge (GCD) measurements revealed a maximum aerial capacitance value of 131.2 mF cm-2 for the best WS2 electrode and a value of 97.60 mF cm-2 for the best MoS2 electrode. The flexibilities of the SC devices were examined using angle-dependent CV measurements, which revealed almost no change. Stability tests for 10 000 cycles showed a retention rate of over 96% capacitance for both electrodes. This research demonstrates the potential of integrating the conductivity, large surface/volume ratio, and processability of G-CNTs with the unique features of transition metal dichalcogenides to develop SCs with improved efficiencies and flexibilities.

Improved electrochemical performance of multi-walled carbon nanotube reinforced gelatin biopolymer for transient energy storage applications

Multi-walled carbon nanotube (MWCNT) incorporated biodegradable gelatin nanocomposites (Gel/MWCNT) have been prepared following a facile solution processing method. The Fourier-transform infrared (FTIR) spectroscopy, field emission scanning electronic microscopy (FESEM), and water contact angle (WCA) measurements revealed improved structural properties and surface morphological features of the nanocomposite films due to the incorporation of MWCNT. A four-fold decrease in the DC resistivity was obtained due to the addition of MWCNTs. The specific capacitance of the nanocomposite increased from 0.12 F/g to 12.7 F/g at a current density of 0.3 μA/cm2 due to the incorporation of 0.05 wt.% MWCNT. EIS analysis and the corresponding Nyquist plots demonstrated the contributions of the different electrical components responsible for the improved electrochemical performance were evaluated using an equivalent AC circuit. The incorporation of MWCNTs was found to reduce the charge-transfer resistance from 127 Ω to 75 Ω and increase the double-layer capacitance from 4 nF to 9 nF. The Gel/MWCNT nanocomposite demonstrated improved cyclic stability with a retention of 95% of the initial capacitance even after 5000 charging/discharging cycles. The biodegradability test showed that the nanocomposite degraded completely after 30 hours of immersion in water. This fully biocompatible nature of the nanocomposites with high specific capacitance and low charge transfer resistance may offer a promising route to fabricate a nature-friendly electrode material for energy storage applications.

Coal Tar Pitch-Based Porous Carbon Loaded MoS2 and Its Application in Supercapacitors

In this paper, with coal tar pitch as the carbon source, porous carbon (PC) was prepared by one-step carbonization. To improve the energy density of coal tar pitch-based porous carbon, MoS2@PC was prepared by a hydrothermal method on a PC substrate. The effect of MoS2 loading on the structure and electrochemical properties of the sample was studied. The results show that the specific surface area of the MoS2@PC-0.3 synthesized is 3053 m2 g-1, and the large specific surface area provides sufficient attachment sites for the storage of electrolyte ions. In the three-electrode system, the specific capacitance of MoS2@PC-0.3 at 0.5 A g-1 is 422.5 F g-1, and the magnification performance is 57.3% at 20 A g-1. After 10,000 charge/discharge cycles, the capacitance retention rate of the sample is 76.73%, with the Coulombic efficiency being 100%. In the two-electrode test system, the specific capacitance of MoS2@PC-0.3 at 0.5 A g-1 is 321.4 F g-1, with the power density and energy density being 500 W kg-1 and 44.6 Wh kg-1, respectively. At a current density of 20 A g-1, the capacitance retention rate is 87.69% after 10,000 cycles. This study greatly improves the energy density of PC as the electrode material of supercapacitors.

Recent advancements in zero- to three-dimensional carbon networks with a two-dimensional electrode material for high-performance supercapacitors

Supercapacitors have gained significant attention owing to their exceptional performance in terms of energy density and power density, making them suitable for various applications, such as mobile devices, electric vehicles, and renewable energy storage systems. This review focuses on recent advancements in the utilization of 0-dimensional to 3-dimensional carbon network materials as electrode materials for high-performance supercapacitor devices. This study aims to provide a comprehensive evaluation of the potential of carbon-based materials in enhancing the electrochemical performance of supercapacitors. The combination of these materials with other cutting-edge materials, such as Transition Metal Dichalcogenides (TMDs), MXenes, Layered Double Hydroxides (LDHs), graphitic carbon nitride (g-C₃N₄), Metal-Organic Frameworks (MOFs), Black Phosphorus (BP), and perovskite nanoarchitectures, has been extensively studied to achieve a wide operating potential window. The combination of these materials synchronizes their different charge-storage mechanisms to attain practical and realistic applications. The findings of this review indicate that hybrid composite electrodes with 3D structures exhibit the best potential in terms of overall electrochemical performance. However, this field faces several challenges and promising research directions. This study aimed to highlight these challenges and provide insights into the potential of carbon-based materials in supercapacitor applications.

Nanoarchitectonics of Three-Dimensional Carbon Nanofiber-Supported Hollow Copper Sulfide Spheres for Asymmetric Supercapacitor Applications

Three-dimensional carbon nanofiber (3D-CNF)-supported hollow copper sulfide (HCuS) spheres were synthesized by the facile hydrothermal method. The morphology of the as-synthesized HCuS@3D-CNF composite clearly revealed that the 3D-CNFs act as a basement for HCuS spheres. The electrochemical performance of as-synthesized HCuS@3D-CNFs was evaluated by cyclic voltammetry (CV) tests, gravimetric charge-discharge (GCD) tests, and Nyquist plots. The obtained results revealed that the HCuS@3D-CNFs exhibited greater areal capacitance (4.6 F/cm²) compared to bare HCuS (0.64 F/cm²) at a current density of 2 mA/cm². Furthermore, HCuS@3D-CNFs retained excellent cyclic stability of 83.2% after 5000 cycles. The assembled asymmetric device (HCuS@3D-CNFs//BAC) exhibits an energy density of 0.15 mWh/cm² with a working potential window of 1.5 V in KOH electrolyte. The obtained results demonstrate that HZnS@3D-CNF nanoarchitectonics is a potential electrode material for supercapacitor applications.

Morphology Engineering of Hybrid Supercapacitor Electrodes from Hierarchical Stem-like Carbon Networks with Flower-like MoS2 Structures

There is a critical need to develop high-performance supercapacitors that can complement and even rival batteries for energy storage. This work introduces a strategy to drastically enhance the energy storage performance of a supercapacitor by engineering electrode morphologies with ternary composites offering distinct benefits for the energy storage application. The electrodes were fabricated with conductive networks of carbon nanotubes (CNTs) coated with a zeolitic imidazole framework (ZIF) for high ion diffusivity and ion-accumulating molybdenum disulfide (MoS₂) with various morphologies. These include flower-like (fMoS₂), stacked-plate (pMoS₂), and exfoliated-flake (eMoS₂) structures from topochemical synthesis. CNT-ZIF-fMoS₂ demonstrates an excellent energy density, reaching almost 80 Wh/kg, and a maximum power density of approximately 3000 W/kg in a half-cell. This is far superior to the electrodes containing pMoS₂ and eMoS₂ and attributed to the increased surface area and the faradaic reactivity offered by fMoS₂. Additionally, the CNT-ZIF-fMoS₂ electrode demonstrates exceptional stability with an ∼78% of capacitance retention over 10,000 cycles. This work suggests that the electrode morphologies can dominate the energy storage behaviors and that the heteromaterial approach may be crucial in designing next-generation supercapacitors.

Direct Growth of Binder-Free CNTs on a Nickel Foam Substrate for Highly Efficient Symmetric Supercapacitors

In the modern civilized world, energy scarcity and associated environmental pollution are the center of focus in the search for reliable energy storage and harvesting devices. The need to develop cheaper and more competent binder-free electrodes for high-performance supercapacitors has attracted considerable research attention. In this study, two different procedures are followed to enhance the growth of carbon nanotubes (CNT-E and CNT-NF) directly coated on a Ni-foam substrate by a well-functioning chemical vapor deposition (CVD) method. Thus, directly grown optimized CNT electrodes are used as electrodes for electrochemical devices. Furthermore, solid-state symmetric supercapacitors are fabricated using CNT-NF//CNT-NF, and fruitful results are obtained with maximum specific capacitance (250.51 F/g), energy density (68.19 Wh/kg), and power density (2799.77 W/kg) at 1 A/g current density. The device exhibited good cyclic stability, with 92.42% capacitive retention and 99.68% Coulombic efficiency at 10 000 cycles, indicating the suitability of the electrodes for practical applications. This study emphasizes the importance of studying the direct growth of binder-free CNT electrodes to understand the actual behavior of electrodes and the proper storage mechanism.

Ex Situ Characterization of 1T/2H MoS2 and Their Carbon Composites for Energy Applications, a Review

The growing interest in the development of next-generation net zero energy systems has led to the expansion of molybdenum disulfide (MoS₂) research in this area. This activity has resulted in a wide range of manufacturing/synthesis methods, controllable morphologies, diverse carbonaceous composite structures, a multitude of applicable characterization techniques, and multiple energy applications for MoS₂. To assess the literature trends, 37,347 MoS₂ research articles from Web of Science were text scanned to classify articles according to energy application research and characterization techniques employed. Within the review, characterization techniques are grouped under the following categories: morphology, crystal structure, composition, and chemistry. The most common characterization techniques identified through text scanning are recommended as the base fingerprint for MoS₂ samples. These include: scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Similarly, XPS and Raman spectroscopy are suggested for 2H or 1T MoS₂ phase confirmation. We provide guidance on the collection and presentation of MoS₂ characterization data. This includes how to effectively combine multiple characterization techniques, considering the sample area probed by each technique and their statistical significance, and the benefit of using reference samples. For ease of access for future experimental comparison, key numeric MoS₂ characterization values are tabulated and major literature discrepancies or currently debated characterization disputes are highlighted.

MoS2 nanosheets on plasma-nitrogen-doped carbon cloth for high-performance flexible supercapacitors

With the surging demand for flexible and portable electronic devices featuring high energy and power density, the development of next-generation lightweight, flexible energy storage devices is crucial. However, achieving the expected energy and power density of supercapacitors remains a great challenge. This work reports a facile plasma-enabled method for preparing supercapacitor electrodes made of MoS2 nanosheets grown on flexible and lightweight N-doped carbon cloth (NCC). The MoS2/NCC presents an outstanding specific capacitance of 3834.28 mF/cm2 at 1 mA/cm2 and energy density of 260.94 µWh/cm2 at a power density of 354.48 µW/cm2. An aqueous symmetric supercapacitor fitted with two MoS2/NCC electrodes achieved the maximum energy density of 138.12 µWh/cm2 and the highest power density of 7,417.33 µW/cm2, along with the excellent cycling stability of 83.3 % retention over 10,000 cycles. The high-performance energy storage ASSSs (all-solid-state supercapacitors) are demonstrated to power devices in both rigid and flexible operation modes. This work provides a new perspective for fabricating high-performance all-solid-state flexible supercapacitors for clean energy storage.

Facile Synthesis of Biocarbon-Based MoS2 Composite for High-Performance Supercapacitor Application

Nanocomposites are gaining high demand for the development of next-generation energy storage devices because of their eco-friendly and cost-effective natures. However, their short-term energy retainability and marginal stability are regarded as hindrances to overcome. In this work, we demonstrate a high-performance supercapacitor fabricated by biocarbon-based MoS₂ (Bio-C/MoS₂) nanoparticles synthesized by a facile hydrothermal approach using date fruits. Here, we report the high specific capacitance for a carbon-based nanocomposite employing the pyrolysis technique of converting agricultural biowaste into a highly affordable energy resource. The biocompatible Bio-C/MoS₂ nanospheres exhibited a high capacitance of 945 F g^-1 at a current density of 0.5 A g^-1 and an excellent reproducing stability of 92% after 10000 charge/discharge cycles. In addition, the Bio-C/MoS₂ NS showed an exceptional power density of 3800-8000 W kg^-1 and an energy density of 74.9-157 Wh kg^-1. The results would pave a new strategy for design of eco-friendly materials toward the high-performance energy storage technology.

High-Performance MnO2 Nanowire/MoS2 Nanosheet Composite for a Symmetrical Solid-State Supercapacitor

To improve the production rate of MoS₂ nanosheets as an excellent supercapacitor (SC) material and enhance the performance of the MoS₂-based solid-state SC, a liquid phase exfoliation method is used to prepare MoS₂ nanosheets on a large scale. Then, the MnO₂ nanowire sample is synthesized by a one-step hydrothermal method to make a composite with the as-synthesized MoS₂ nanosheets to achieve a better performance of the solid-state SC. The interaction between the MoS₂ nanosheets and MnO₂ nanowires produces a synergistic effect, resulting in a decent energy storage performance. For practical applications, all-solid-state SC devices are fabricated with different molar ratios of MoS₂ nanosheets and MnO₂ nanowires. From the experimental results, it can be seen that the synthesized nanocomposite with a 1:4 M ratio of MoS₂ nanosheets and MnO₂ nanowires exhibits a high Brunauer-Emmett-Teller surface area (∼118 m²/g), optimum pore size distribution, a specific capacitance value of 212 F/g at 0.8 A/g, an energy density of 29.5 W h/kg, and a power density of 1316 W/kg. Besides, cyclic charging-discharging and retention tests manifest significant cycling stability with 84.1% capacitive retention after completing 5000 rapid charge-discharge cycles. It is believed that this unique, symmetric, lightweight, solid-state SC device may help accomplish a scalable approach toward powering forthcoming portable energy storage applications.

Dielectric Barrier Discharge Plasma Jet (DBDjet) Processed Reduced Graphene Oxide/Polypyrrole/Chitosan Nanocomposite Supercapacitors

Reduced graphene oxide (rGO) and/or polypyrrole (PPy) are mixed with chitosan (CS) binder materials for screen-printing supercapacitors (SCs) on arc atmospheric-pressure plasma jet (APPJ)-treated carbon cloth. The performance of gel-electrolyte rGO/CS, PPy/CS, and rGO/PPy/CS SCs processed by a dielectric barrier discharge plasma jet (DBDjet) was assessed and compared. DBDjet processing improved the hydrophilicity of these three nanocomposite electrode materials. Electrochemical measurements including electrical impedance spectroscopy (EIS), cyclic voltammetry (CV), and galvanostatic charging-discharging (GCD) were used to evaluate the performance of the three types of SCs. The Trasatti method was used to evaluate the electric-double layer capacitance (EDLC) and pseudocapacitance (PC) of the capacitance. The energy and power density of the three types of SCs were illustrated and compared using Ragone plots. Our experiments verify that, with the same weight of active materials, the combined use of rGO and PPy in SCs can significantly increase the capacitance and improve the operation stability.

Bio-inspired gelatin/single-walled carbon nanotube nanocomposite for transient electrochemical energy storage: An approach towards eco-friendly and sustainable energy system

Wide-scale production of non-biodegradable e-waste from electrical appliances are causing great harm to the environment. The use of bio-polymer based nanomaterials may offer a promising approach for the fabrication of eco-friendly sustainable devices. In this work, gelatin/single walled carbon nanotube (Gel/SWCNT) nanocomposites were prepared by a simple and economic aqueous casting method. The effect of SWCNT on the structural, surface-morphological, electrical, and electrochemical properties of the nanocomposite was studied. Fourier transform infrared spectroscopy (FTIR) and field emission scanning electron microscope (FESEM) showed an improved degree of interaction between the SWCNTs and Gel matrix. The surface wettability of the nanocomposites was found to be changed from hydrophilic to hydrophobic in nature due to the incorporation of SWCNTs into the Gel matrix. The incorporation of SWCNTs was also found to reduce the DC resistivity of the nanocomposite by 4 orders of magnitude. SWCNTs also increase the specific capacitance of the nanocomposite from 124 mF/g to 467 mF/g at a current density of 0.3 mA/g. The electrochemical impedance spectroscopy analysis revealed an increase of the pseudo-capacitance increased from 9.4 μF to 31 μF due to the incorporation of SWCNT. The Gel/SWCNT nanocomposite showed cyclic stability with capacitive retention of about 98% of its initial capacitance after completing 2000 charging/discharging cycles at a current density of 100 mA/g. The nanocomposite completely dissolves in water within 12 h, demonstrates it as a promising candidate for transient energy storage applications. The Gel/SWCNT nanocomposite may offer a new route for the synthesis of eco-friendly, biodegradable, and transient devices.

Electropolymerized Poly(3,4-ethylenedioxythiophene)/Screen-Printed Reduced Graphene Oxide-Chitosan Bilayer Electrodes for Flexible Supercapacitors

An electropolymerized poly(3,4-ethylenedioxythiophene) (PEDOT)/screen-printed reduced graphene oxide (rGO)-chitosan (CS) bilayer material was coated on carbon cloth to form electrodes for gel-electrolyte flexible supercapacitors. The conductive polymer and carbon-based materials mainly contribute pseudocapacitance (PC) and electrical double-layer capacitance (EDLC), respectively. The high porosity and hydrophilicity of the PEDOT/rGO-CS bilayer material offers a large contact area and improves the contact quality for the gel electrolyte, thereby enhancing the capacitive performance. Cyclic voltammetry (CV) under a potential scan rate of 2 mV/s revealed that a maximum areal capacitance of 1073.67 mF/cm² was achieved. The capacitance contribution ratio PC/EDLC was evaluated to be ∼67/33 by the Trasatti method. A 10,000-cycle CV test showed a capacitance retention rate of 99.3% under a potential scan rate of 200 mV/s, indicating good stability. The areal capacitance remains similar under bending with a bending curvature of up to 1.5 cm^-1.

Carbon Dioxide Tornado-Type Atmospheric-Pressure-Plasma-Jet-Processed rGO-SnO2 Nanocomposites for Symmetric Supercapacitors

Pastes containing reduced graphene oxide (rGO) and SnCl2 solution were screen printed on carbon cloth and then calcined using a CO2 tornado-type atmospheric-pressure plasma jet (APPJ). The tornado circulation of the plasma gas enhances the mixing of the reactive plasma species and thus ensures better reaction uniformity. Scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) were performed to characterize the synthesized rGO-SnO2 nanocomposites on carbon cloth. After CO2 tornado-type APPJ treatment, the pastes were converted into rGO-SnO2 nanocomposites for use as the active electrode materials of polyvinyl alcohol (PVA)-H2SO4 gel-electrolyte flexible supercapacitors (SCs). Various APPJ scanning times were tested to obtain SCs with optimized performance. With seven APPJ scans, the SC achieved the best areal capacitance of 37.17 mF/cm2 in Galvanostatic charging/discharging (GCD) and a capacitance retention rate of 84.2% after 10,000-cycle cyclic voltammetry (CV) tests. The capacitance contribution ratio, calculated as pseudocapacitance/electrical double layer capacitance (PC/EDLC), is ~50/50 as analyzed by the Trasatti method. GCD data were also analyzed to obtain Ragone plots; these indicated an energy density comparable to those of SCs processed using a fixed-point nitrogen APPJ in our previous study.

Energy storage performance of 2D MoS2 and carbon nanotube heterojunctions in symmetric and asymmetric configuration

Excellent cyclic stability and fast charge/discharge capacity demonstrated by supercapacitors foster research interest into new electrode materials with 100% cycle life and high specific capacitance. We report an improvement in the electrochemical performance of MoS₂/multiwalled carbon nanotubes (MWCNT) nanohybrid and intensively explored its performance in symmetric and asymmetric supercapacitor (ASC) assembly. The symmetric assembly of MoS₂/MWCNT exhibits capacitance of around 274.63 F g^-1 at 2 A g^-1 with higher specific energy/power outputs (20.70 Wh kg^-1/1.49 kW kg^-1) as compared to the supercapacitor based on pristine MoS₂ (5.82 Wh kg^-1/1.07 kW kg^-1). On the other hand, a unique all-carbon-based ASC assembled with MoS₂/MWCNT and VSe₂/MWCNT composite with K₂SO₄ as electrolyte delivers the highest energy density of 32.18 Wh kg^-1 at a power density of 1.121 kW kg^-1 with exceptional cycling stability and excellent retention of about 98.43% even after 5000 cycles. These outstanding results demonstrate the excellent electrochemical properties of both symmetric and asymmetric systems with high energy density and performance, which further enable them to be a potential candidate for supercapacitor applications.

Photocatalytic Activity of S-Scheme Heterostructure for Hydrogen Production and Organic Pollutant Removal: A Mini-Review

Finding new technologies and materials that provide real alternatives to the environmental and energy-related issues represents a key point on the future sustainability of the industrial activities and society development. The water contamination represents an important problem considering that the quantity and complexity of organic pollutant (such as dyes, pesticides, pharmaceutical active compounds, etc.) molecules can not be efficiently addressed by the traditional wastewater treatments. The use of fossil fuels presents two major disadvantages: (1) environmental pollution and (2) limited stock, which inevitably causes the energy shortage in various countries. A possible answer to the above issues is represented by the photocatalytic technology based on S-scheme heterostructures characterized by the use of light energy in order to degrade organic pollutants or to split the water molecule into its components. The present mini-review aims to outline the most recent achievements in the production and optimization of S-scheme heterostructures for photocatalytic applications. The paper focuses on the influence of heterostructure components and photocatalytic parameters (photocatalyst dosage, light spectra and intensity, irradiation time) on the pollutant removal efficiency and hydrogen evolution rate. Additionally, based on the systematic evaluation of the reported results, several perspectives regarding the future of S-scheme heterostructures were included.

One-Pot Hydrothermal Synthesis of Solution-Processable MoS2/PEDOT:PSS Composites for High-Performance Supercapacitors

It is challenging to hydrothermally synthesize solution-processable MoS₂, as the strong van der Waals force between MoS₂ nanosheets induces self-assembly of agglomerates. Here, we introduce poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) into the precursor to impede aggregate formation in the hydrothermal process. A hybrid MoS₂/PEDOT:PSS (MP) hydrogel is formed due to the electrostatic interactions between the negatively charged MoS₂ and positively charged PEDOT chains. This hydrogel can be easily dispersed in water for subsequent solution processing such as vacuum filtration to form free-standing flexible films or extrusion 3D printing to create novel patterns. The MP film with a fracture strength of 18.59 MPa displays excellent electrochemical performance in both aqueous Na₂SO₄ electrolyte (474 mF cm^-2) and solid-state PVA-H₃PO₄ electrolyte (360 mF cm^-2). Flexibility and robustness can be evidenced by high capacitance retention rates of 94 and 89% after being repeatedly bent to 180° for 5000 cycles in aqueous and solid-state electrolytes, respectively.

Elevated performance of binder-free Co3O4 electrode for the supercapacitor applications

In the present work, we have designed a symmetric supercapacitor (SS) device by synthesizing a pseudocapacitive binder-free cobalt oxide (Co3O4) thin film based electrode using reactive DC magnetron sputtering technique. The thin film electrodes were characterized by x-ray diffraction, Raman spectroscopy and x-ray photoelectron spectroscopy to reveal the crystallographic details, stoichiometry, and electronic configuration, respectively. Furthermore, Co3O4 thin film electrode is used for pseudocapacitor and electrochemically tested in 1M aqueous KOH electrolyte solution, in addition, a symmetric supercapacitor (SS) device was fabricated. It was found that the SS device exhibits tremendous electrochemical stability in terms of high capacitance and good cycling stability. The value of specific capacitance for Co3O4 thin film electrodes and the SS device was calculated to be 392 Fg−1 and 95 Fg−1, respectively, at a scan rate of 2 mAcm−2. The SS device exhibits high specific energy (29 W-hkg−1) along with comparable good specific power (4745 Wkg−1). In this work, the fabricated SS device demonstrates 91.40% cyclic and capacitance retention at 8 mAcm−2 beyond 10 000 cycles. The excellent electrochemical stability and capacitive performance of the SS device suggest that it would be an ideal and potential candidate for energy storage applications in the future.