Effect of biochar modified with magnetite nanoparticles and HNO3 for efficient removal of Cr(VI) from contaminated water: A batch and column scale study

Enhanced Cr(VI) elimination from water by goethite-impregnated activated carbon coupled with weak electric field

A weak electric field (WEF, 2 mA cm-2) was employed to promote Fe(III)/Fe(II) cycle on goethite-impregnated activated carbon (FeOOH@AC) filled in a continuous-flow column for enhanced Cr(VI) elimination from water. Surficial analysis and Cr species distribution showed that α-FeOOH of 0.2-1 μm was successfully synthesized and evenly loaded onto AC. Electron transfer from WEF to α-FeOOH was facilitated with AC as electron shuttles, thereby boosting Fe(III) reduction in the α-FeOOH. The generated Fe(II) reduced Cr(VI) and the resultant Cr(III) subsequently precipitated with OH- and Fe(III) to form Cr(OH)3 and (CrχFe1-χ)(OH)3. Therefore, the WEF-FeOOH@AC column exhibited a much lower Cr(VI) migration rate of 0.0018 cm PV-1 in comparison with 0.0037 cm PV-1 of the FeOOH@AC column, equal to 104 % higher Cr(VI) elimination capacity and 90 % longer column service life-span. Additionally, under different Cr(VI) loadings by varying either seepage velocities or influent Cr(VI) concentrations, the WEF-FeOOH@AC column maintained 1.0-1.5 folds higher Cr(VI) elimination and 0.9-1.4 folds longer longevity than those of the FeOOH@AC column owing to the interaction between FeOOH@AC and WEF. Our research demonstrated that WEF-FeOOH@AC was a potential method to promote Cr(VI) elimination from water and offer an effective strategy to facilitate Fe(III)/Fe(II) cycle in iron oxides.

Removal of Cr(vi) in wastewater by Fe-Mn oxide loaded sludge biochar

Sludge biochar loaded with Fe-Mn oxides (FMBC) was prepared and employed to remove Cr(vi) from wastewater. The influences of solution pH, co-existing ion, contact time, adsorption temperature and Cd(vi) concentrations on removing Cr(vi) by FMBC were investigated. The Cr(vi) adsorption on FMBC had strong pH dependence. Additionally, Na+, Mg2+, Ca2+, SiO32-, NO3- and Cl- ions exhibited no influence on Cr(vi) removal efficiency for FMBC, whereas there were inhibition effects of Pb2+, Cu2+, Ni2+, CO32-, SO42-, and PO43- on removing Cr(vi). The Cr(vi) adsorption from solution for FMBC was well described by models of pseudo-second-order and Langmuir, and the largest Cr(vi) removal capacity of FMBC reached 172.3 mg g-1. FMBC had good capacity for treating electroplating wastewater and mineral dissolving wastewater containing Cr(vi). After five regenerations, the 50 and 5 mg L-1 Cr(vi) removing efficiency of FMBC was 82.34% and 97.68%, respectively. The Cr(vi) removal for FMBC involved adsorption-reduction and re-adsorption of Cr(iii) generated by reduction. These results indicated that FMBC has good prospects for remediating Cr(vi)-containing wastewater.

Silicon-nanoparticles loaded biochar for soil arsenic immobilization and alleviation of phytotoxicity in barley: Implications for human health risk

Arsenic (As)-induced environmental pollution and associated health risks are recognized on a global level. Here the impact of cotton shells derived biochar (BC) and silicon-nanoparticles loaded biochar (nano-Si-BC) was explored on soil As immobilization and its phytotoxicity in barley plants in a greenhouse study. The barley plants were grown in a sandy loam soil with varying concentrations of BC and nano-Si-BC (0, 1, and 2%), along with different levels of As (0, 5, 10, and 20 mg kg-1). The FTIR spectroscopy, SEM-EDX, and XRD were used to characterize BC and nano-Si-BC. Results revealed that As treatment had a negative impact on barley plant development, grain yield, physiology, and anti-oxidative response. However, the addition of nano-Si-BC led to a 71% reduction in shoot As concentration compared to the control with 20 mg kg-1 of As, while BC alone resulted in a 51% decline. Furthermore, the 2% nano-Si-BC increased grain yield by 94% compared to control and 28% compared to BC. The addition of 2% nano-Si-BC to As-contaminated soil reduced oxidative stress (34% H2O2 and 48% MDA content) and enhanced plant As tolerance (92% peroxidase and 46% Ascorbate peroxidase activity). The chlorophyll concentration in barley plants decreased due to oxidative stress. Additionally, the incorporation of 2% nano-Si-BC resulted in a 76% reduction in water soluble and NaHCO3 extractable As. It is concluded that the use of BC or nano-Si-BC in As contaminated soil for barley resulted in a low human health risk (HQ < 1), as it effectively immobilized As and promoted higher activity of antioxidants.

Biochar as Alternative Material for Heavy Metal Adsorption from Groundwaters: Lab-Scale (Column) Experiment Review

The purpose of this manuscript is to present a review of laboratory experiments (including methodology and results) that use biochar, a specific carbon obtained by a pyrolysis process from different feedstocks, as an alternative material for heavy metal adsorption from groundwater. In recent years, many studies have been conducted regarding the application of innovative materials to water decontamination to develop a more sustainable approach to remediation processes. The use of biochar for groundwater remediation has particularly attracted the interest of researchers because it permits the reuse of materials that would be otherwise disposed of, in accordance with circular economy, and reduces the generation of greenhouse gases if compared to the use of virgin materials. A review of the different approaches and results reported in the current literature could be useful because when applying remediation technologies at the field scale, a preliminary phase in which the suitability of the adsorbent is evaluated at the lab scale is often necessary. This paper is therefore organised with a short description of the involved metals and of the biochar production and composition. A comprehensive analysis of the current knowledge related to the use of biochar in groundwater remediation at the laboratory scale to obtain the characteristic parameters of the process that are necessary for the upscaling of the technology at the field scale is also presented. An overview of the results achieved using different experimental conditions, such as the chemical properties and dosage of biochar as well as heavy metal concentrations with their different values of pH, is reported. At the end, numerical studies useful for the interpretation of the experiment results are introduced.

Parameter Influence, Characterization and Adsorption Mechanism Studies of Alkaline-Hydrolyzed Garcinia kola Hull Particles for Cr(VI) Sequestration

Despite the regulations by The World Health Organization (WHO) on the permissible limit of chromium, many industries still discharge wastewater polluted with chromium into the environment irrationally. This poses a lot of risk to aquatic lives and humans because of its carcinogenic and toxic attributes. Thus, treatment of industrial wastewater polluted with chromium is highly imperative before its disposal. Nonetheless, the hulls generated from Garcinia kola in our various farmlands also causes environmental pollution when dumped unknowingly. In this present study, Garcinia kola hull particles (GK-HP) was hydrolyzed using NaOH and applied as adsorbent for Cr(VI) sequestration. The raw Garcinia kola hull particles (rGK-HP) and modified Garcinia kola hull particles (cMGK-HP) were characterized using Brunauer-Emmett-Teller (BET) method, scanning electron microscopy (SEM), powder X-ray diffractometry (XRD), Fourier-Transform-Infrared (FTIR), thermogravimetric analysis (TGA), energy dispersive spectroscopy (EDS) and point of zero charge (pHpzc). The influence of pH, adsorbent dose, contact time, temperature and adsorbate initial concentration on Cr(VI) sequestration were examined. The cMGK-HP was able to remove 96.25% of Cr(VI) from solution and proved to be effective than rGK-HP. The amount of Cr(VI) removed from solution decreased as the pH and adsorbate initial concentration were increased. However, the amount increased as the adsorbent dose, contact time and temperature were increased. Change in morphological structure, textural property, spectral peak, phase composition and adsorbents chemical composition before and after Cr(VI) sequestration from solution were proved by SEM, BET, FTIR, XRD, and EDS analyses respectively. The isotherm and kinetic studies suggest Cr(VI) adsorption on adsorbents' surface to be monolayer in nature and adsorption data to be well-fitted into pseudo second order model respectively. The cMGK-HP possessed excellent reusability attribute and high thermal stability as shown by TGA. In conclusion, cMGK-HP could effectively be used as an adsorbent for Cr(VI) sequestration from solution.

Machine learning based prediction and experimental validation of arsenite and arsenate sorption on biochars

Arsenic (As) contamination in water is a significant environmental concern with profound implications for human health. Accurate prediction of the adsorption capacity of arsenite [As(III)] and arsenate [As(V)] on biochar is vital for the reclamation and recycling of polluted water resources. However, comprehending the intricate mechanisms that govern arsenic accumulation on biochar remains a formidable challenge. Data from the literature on As adsorption to biochar was compiled and fed into machine learning (ML) based modelling algorithms, including AdaBoost, LGBoost, and XGBoost, in order to build models to predict the adsorption efficiency of As(III) and As(V) to biochar, based on the compositional and structural properties. The XGBoost model showed superior accuracy and performance for prediction of As adsorption efficiency (for As(III): coefficient of determination (R2) = 0.93 and root mean square error (RMSE) = 1.29; for As(V), R2 = 0.99, RMSE = 0.62). The initial concentrations of As(III) and As(V) as well as the dosage of the adsorbent were the most significant factors influencing adsorption, explaining 48 % and 66 % of the variability for As(III) and As(V), respectively. The structural properties and composition of the biochar explained 12 % and 40 %, respectively, of the variability of As(III) adsorption, and 13 % and 21 % of that of As(V). The XGBoost models were validated using experimental data. R2 values were 0.9 and 0.84, and RMSE values 6.5 and 8.90 for As(III) and As(V), respectively. The ML approach can be a valuable tool for improving the treatment of inorganic As in aqueous environments as it can help estimate the optimal adsorption conditions of As in biochar-amended water, and serve as an early warning for As-contaminated water.

Chromium removal from aqueous solution using bimetallic Bi0/Cu0-based nanocomposite biochar

Chromium (Cr), due to its greater contamination in aquifers and distinct eco-toxic impacts, is of greater environmental concern. This study aimed to synthesize nanocomposites of almond shells biochar (BC) with zerovalent bismuth and/or copper (Bi0/BC, Cu0/BC, and Bi0-Cu0/BC) for the removal of Cr from aqueous solution. The synthesized nanocomposites were investigated using various characterization techniques such as XRD, FTIR spectroscopy, SEM, and EDX. The Cr removal potential by the nanocomposites was explored under different Cr concentrations (25-100 mg/L), adsorbent doses (0.5-2.0 g/L), solution pH (2-8), and contact time (10-160 min). The above-mentioned advanced techniques verified successful formation of Bi0/Cu0 and their composite with BC. The synthesized nanocomposites were highly effective in the removal of Cr. The Bi0-Cu0/BC nano-biocomposites showed higher Cr removal efficiency (92%) compared to Cu0/BC (85%), Bi0/BC (76%), and BC (67%). The prepared nanocomposites led to effective Cr removal at lower Cr concentrations (25 mg/L) and acidic pH (4.0). The Cr solubility changes with pH, resulting in different degrees of Cr removal by Bi0-Cu0/BC, with Cr(VI) being more soluble and easier to adsorb at low pH levels and Cr(III) being less soluble and more difficult to adsorb at high pH levels. The experimental Cr adsorption well fitted with the Freundlich adsorption isotherm model (R2 > 0.99) and pseudo-second-order kinetic model. Among the prepared nanocomposites, the Bi0-Cu0/BC showed greater stability and reusability. It was established that the as-synthesized Bi0-Cu0/BC nano-biocomposite showed excellent adsorption potential for practical Cr removal from contaminated water.

Comparison of As removal efficiency and health risks from aqueous solution using as-synthesized Fe0 and Cu0: modelling, kinetics and reusability

Batch scale removal of arsenic (As) from aqueous media was explored using nano-zero valent iron (Fe0) and copper (Cu0) particles. The synthesized particles were characterized using a Brunauer-Emmett-Teller (BET) surface area analyzer, a scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FTIR). The BET result showed that the surface area (31.5 m2/g) and pore volume (0.0415 cm3/g) of synthesized Fe0 were higher than the surface area (17.56 m2/g) and pore volume (0.0287 cm3/g) of Cu0. The SEM results showed that the morphology of the Fe0 and Cu0 was flowery microspheres and highly agglomerated with thin flakes. The FTIR spectra for Fe0 showed broad and intense peaks as compared to Cu0. The effects of the adsorbent dose (1-4 g/L), initial concentration of As (2 mg/L to 10 mg/L) and solution pH (2-12) were evaluated on the removal of As. Results revealed that effective removal of As was obtained at pH 4 with Fe0 (94.95%) and Cu0 (74.86%). When the dosage increased from 1 to 4 g L-1, the As removal increased from 70.59 to 93.02% with Fe0 and from 67 to 70.59% with Cu0. However, increasing the initial As concentration decreased the As removal significantly. Health risk indices, including estimated daily intake (EDI), hazard quotient (HQ), and cancer risk (CR) were employed and a significant decline (up to 99%) in risk indices was observed in As-treated water using Fe0/Cu0. Among the adsorption isotherm models, the values of R2 showed that isothermal As adsorption by Fe0 and Cu0 was well explained by the Freundlich adsorption isotherm model (R2 > 0.98) while the kinetic experimental data was well-fitted with the Pseudo second order model. The Fe0 showed excellent stability and reusability over five sorption cycles, and it was concluded that, compared to the Cu0, the Fe0 could be a promising technology for remediating As-contaminated groundwater.

Research on the performance of modified blue coke in adsorbing hexavalent chromium

To solve the issue of hexavalent chromium (Cr(VI)) contamination in water bodies, blue coke powder (LC) was chemically changed using potassium hydroxide to create the modified material (GLC), which was then used to treat a Cr(VI)-containing wastewater solution. The differences between the modified and unmodified blue coke's adsorption characteristics for Cr(VI) were studied, and the impact of pH, starting solution concentration, and adsorption period on the GLC's adsorption performance was investigated. The adsorption behavior of the GLC was analyzed using isothermal adsorption models, kinetic models, and adsorption thermodynamic analysis. The mechanism of Cr(VI) adsorption by the GLC was investigated using characterization techniques such as Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscope (FE-SEM), X-Ray Diffraction (XRD), and X-Ray Photoelectron Spectroscopy (XPS). With the biggest difference in removal rate at pH = 2, which was 2.42 times that of LC, batch adsorption experiments revealed that, under the same adsorption conditions, the GLC always performed better than LC. With a specific surface area that was three times that of LC and an average pore diameter that was 0.67 times that of LC, GLC had a more porous structure than LC. The alteration significantly increased the number of hydroxyls on the surface of GLC by altering the structural makeup of LC. The ideal pH for removing Cr(VI) was 2, and the ideal GLC adsorbent dosage was 2.0 g/L. Pseudo-second-order kinetic (PSO) model and Redlich-Peterson (RP) model can effectively describe the adsorption behavior of GLC for Cr(VI). Physical and chemical adsorption work together to remove Cr(VI) by GLC in a spontaneous, exothermic, and entropy-increasing process, with oxidation-reduction processes playing a key role. GLC is a potent adsorbent that can be used to remove Cr(VI) from aqueous solutions.

Extraction of Humic Acids from Lignite and Its Use as a Biochar Activator

Current research focuses on extracting humic acid (HA) compounds from low-rank coals to obtain high value-added products. In this study, HAs with high purity and low heavy metal content were obtained from lignite by combining acid pretreatment with hydrothermal treatment. Scanning electron microscopy, elemental analysis (EA), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction, and inductively coupled plasma optical emission spectrometry (ICP-OES) were used to analyze raw lignite and HAs. The effects of acid and hydrothermal treatments on the inorganic elements, functional groups, and yield of HAs were examined. The results showed that acid treatment reduced the ash content of lignite from 20 to 9%, and hydrothermal treatment increased the yield of HAs from 36 to 68%. The chemical properties of HAs exhibited an increase in molecular weight and improved aromaticity after acid and hydrothermal treatments. The results of ICP-OES analysis suggested that the combined method of acid and hydrothermal treatments resulted in a significant reduction of heavy metal elements in HAs. FTIR analysis confirmed the results and demonstrated that the extracted HA from nitric acid pretreated and hydrothermal generation of lignite PHA was rich in carboxyl and phenolic functional groups. PHA was applied to biochar as an activator for the adsorption of heavy metal ions. The experimental results showed that PHA was successfully loaded onto biochar and introduced a large number of functional groups, and the adsorption capacity of the modified biochar for Pb²⁺ was effectively improved.

A Comprehensive Review of the Current Progress of Chromium Removal Methods from Aqueous Solution

Chromium (Cr) exists in aqueous solution as trivalent (Cr³⁺) and hexavalent (Cr⁶⁺) forms. Cr³⁺ is an essential trace element while Cr⁶⁺ is a dangerous and carcinogenic element, which is of great concern globally due to its extensive applications in various industrial processes such as textiles, manufacturing of inks, dyes, paints, and pigments, electroplating, stainless steel, leather, tanning, and wood preservation, among others. Cr³⁺ in wastewater can be transformed into Cr⁶⁺ when it enters the environment. Therefore, research on Cr remediation from water has attracted much attention recently. A number of methods such as adsorption, electrochemical treatment, physico-chemical methods, biological removal, and membrane filtration have been devised for efficient Cr removal from water. This review comprehensively demonstrated the Cr removal technologies in the literature to date. The advantages and disadvantages of Cr removal methods were also described. Future research directions are suggested and provide the application of adsorbents for Cr removal from waters.

Modified magnetic chitosan materials for heavy metal adsorption: a review

Magnetic chitosan materials have the characteristics of both chitosan and magnetic particle nuclei, showing the characteristics of easy separation and recovery, strong adsorption capacity and high mechanical strength, and have received extensive attention in adsorption, especially in the treatment of heavy metal ions. In order to further improve its performance, many studies have modified magnetic chitosan materials. This review discusses the strategies for the preparation of magnetic chitosan using coprecipitation, crosslinking, and other methods in detail. Besides, this review mainly summarizes the application of modified magnetic chitosan materials in the removal of heavy metal ions in wastewater in recent years. Finally, this review also discusses the adsorption mechanism, and puts forward the prospect of the future development of magnetic chitosan in wastewater treatment.

Potential of magnetic quinoa biosorbent composite and HNO3 treated biosorbent for effective sequestration of chromium (VI) from contaminated water

The present study aims to prepare novel quinoa biosorbent (QB), acid activated QB (QB/Acid) and its nanocomposite with magnetic nanoparticles (QB/MNPs) for batch scale Cr removal from contaminated water. The Cr adsorption was systematically studied at different pH (2-9), adsorbent dosage (1-3 g/L), initial concentration (25-200 mg/L), contact time (180 min) and competing ions in water. Maximum Cr adsorption was observed onto QB/MNPs (57.4 mg/L), followed by QB/Acid (46.35 mg/g) and QB (39.9 mg/g). The Cr removal by QB/MNPs was higher than QB/Acid and QB. Results revealed that the highest Cr removal was obtained at optimum pH 4, 25 mg/L, and 2 g/L dosage. The FTIR spectra displayed various functional groups on adsorbents surface serving as a potential scaffold to remove Cr from contaminated water. The equilibrium and kinetic Cr adsorption data best fitted with Freundlich and pseudo-second order models, respectively (R² ≥ 0.96). The QB/MNPs showed excellent reusability in five adsorption/desorption cycles (4.7% decline) with minor leaching of Fe (below threshold level). The coexisting ions in groundwater showed an inhibitory effect on Cr sequestration (5%) from water. The comparison of Cr adsorption by QB/MNPs and QB/Acid showed better potential for Cr sequestration than various previously explored adsorbents in the literature.

Removal of hexavalent chromium via biochar-based adsorbents: State-of-the-art, challenges, and future perspectives

Chromium originates from geogenic and extensive anthropogenic activities and significantly impacts natural ecosystems and human health. Various methods have been applied to remove hexavalent chromium (Cr(VI)) from aquatic environmental matrices, including adsorption via different adsorbents, which is considered to be the most common and low-cost approach. Biochar materials have been recognized as renewable carbon sorbents, pyrolyzed from various biomass at different temperatures under limited/no oxygen conditions for heavy metals remediation. This review summarizes the sources, chemical speciation & toxicity of Cr(VI) ions, and raw and modified biochar applications for Cr(VI) remediation from various contaminated matrices. Mechanistic understanding of Cr(VI) adsorption using different biochar-based materials through batch and saturated column adsorption experiments is documented. Electrostatic interaction and ion exchange dominate the Cr(VI) adsorption onto the biochar materials in acidic pH media. Cr(VI) ions tend to break down as HCrO₄^-, CrO₄^2-, and Cr₂O₇^2- ions in aqueous solutions. At low pH (∼1-4), the availability of HCrO₄^- ions attributes the electrostatic forces of attraction due to the available functional groups such as -NH₄⁺, -COOH, and -OH₂⁺, which encourages higher adsorption of Cr(VI). Equilibrium isotherm, kinetic, and thermodynamic models help to understand Cr(VI)-biochar interactions and their adsorption mechanism. The adsorption studies of Cr(VI) are summarized through the fixed-bed saturated column experiments and Cr-contaminated real groundwater analysis using biochar-based sorbents for practical applicability. This review highlights the significant challenges in biochar-based material applications as green, renewable, and cost-effective adsorbents for the remediation of Cr(VI). Further recommendations and future scope for the implications of advanced novel biochar materials for Cr(VI) removal and other heavy metals are elegantly discussed.

Biochar-Mediated Zirconium Ferrite Nanocomposites for Tartrazine Dye Removal from Textile Wastewater

To meet the current challenges concerning the removal of dyes from wastewater, an environmentally friendly and efficient treatment technology is urgently needed. The recalcitrant, noxious, carcinogenic and mutagenic compound dyes are a threat to ecology and its removal from textile wastewater is challenge in the current world. Herein, biochar-mediated zirconium ferrite nanocomposites (BC-ZrFe₂O₅ NCs) were fabricated with wheat straw-derived biochar and applied for the adsorptive elimination of Tartrazine dye from textile wastewater. The optical and structural properties of synthesized BC-ZrFe₂O₅ NCs were characterized via UV/Vis spectroscopy, Fourier transform Infra-red (FTIR), X-Ray diffraction (XRD), Energy dispersive R-Ray (EDX) and Scanning electron microscopy (SEM). The batch modes experiments were executed to explore sorption capacity of BC-ZrFe₂O₅ NCs at varying operative conditions, i.e., pH, temperature, contact time, initial dye concentrations and adsorbent dose. BC-ZrFe₂O₅ NCs exhibited the highest sorption efficiency among all adsorbents (wheat straw biomass (WSBM), wheat straw biochar (WSBC) and BC-ZrFe₂O₅ NCs), having an adsorption capacity of (mg g^-1) 53.64 ± 0.23, 79.49 ± 0.21 and 89.22 ± 0.31, respectively, for Tartrazine dye at optimum conditions of environmental variables: pH 2, dose rate 0.05 g, temperature 303 K, time of contact 360 min and concentration 100 mg L^-1. For the optimization of process variables, response surface methodology (RSM) was employed. In order to study the kinetics and the mechanism of the adsorption process, kinetic and equilibrium mathematical models were used, and results revealed 2nd order kinetics and a multilayer chemisorption mechanism due to complexation of hydroxyl, Fe and Zr with dyes functional groups. The nanocomposites were also recovered in five cycles without significant loss (89 to 63%) in adsorption efficacy. This research work provides insight into the fabrication of nanoadsorbents for the efficient adsorption of Tartrazine dye, which can also be employed for practical engineering applications on an industrial scale as efficient and cost effective materials.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

Potential of nanocomposites of zero valent copper and magnetite with Eleocharis dulcis biochar for packed column and batch scale removal of Congo red dye

The current study is the first attempt to prepare nanocomposites of Eleocharis dulcis biochar (EDB) with nano zero-valent Copper (nZVCu/EDB) and magnetite nanoparticles (MNPs/EDB) for batch and column scale sequestration of Congo Red dye (CR) from synthetic and natural water. The adsorbents were characterized with advanced analytical techniques. The impact of EDB, MNPs/EDB and nZVCu/EDB dosage (1-4 g/L), pH (4-10), initial concentration of CR (20-500 mg/L), interaction time (180 min) and material type to remove CR from water was examined at ambient temperature. The CR removal followed sequence of nZVCu/EDB > MNPs/EDB > EDB (84.9-98% > 77-95% > 69.5-93%) at dosage 2 g/L when CR concentration was increased from 20 to 500 mg/L. The MNPs/EDB and nZVCu/EDB showed 10.9% and 20.1% higher CR removal than EDB. The adsorption capacity of nZVCu/EDB, MNPs/EDB and EDB was 212, 193 and 174 mg/g, respectively. Freundlich model proved more suitable for sorption experiments while pseudo 2nd order kinetic model well explained the adsorption kinetics. Fixed bed column scale results revealed excellent retention of CR (99%) even at 500 mg/L till 2 h when packed column was filled with 3.0 g nZVCu/EDB, MNPs/EDB and EDB. These results revealed that nanocomposites with biochar can be applied efficiently for the decontamination of CR contaminated water.

Fabrication, application, and mechanism of metal and heteroatom co-doped biochar composites (MHBCs) for the removal of contaminants in water: A review

The potential risk of various contaminants in water has recently attracted public attention. Biochars and modified biochars have been widely developed for environmental remediation. Metal and heteroatom co-doped biochar composites (MHBCs) quickly caught the interest of researchers with more active sites and higher affinity for contaminants compared to single-doped biochar by metal or heteroatoms. This study provides a comprehensive review of MHBCs in wastewater decontamination. Firstly, the main fabrication methods of MHBCs were external doping and internal doping, with external doping being the most common. Secondly, the applications of MHBCs as adsorbents and catalysts in water treatment were introduced emphatically, which mainly included the removal of metals, antibiotics, dyes, pesticides, phenols, and other organic contaminants. Thirdly, the removal mechanisms of contaminants by MHBCs were deeply discussed in adsorption, oxidation and reduction, and degradation. Furthermore, the influencing factors for the removal of contaminants by MHBCs were also summarized, including the physicochemical properties of MHBCs, and environmental variables of pH and co-existing substance. Finally, futural challenges of MHBCs are proposed in the leaching toxicity of metal from MHBCs, the choice of heteroatoms on the fabrication for MHBCs, and the application in the composite system and soil remediation.

Recycled mesoporous magnetic composites with high surface area derived from plastic and de-oiled sludge wastes: An empirical comparison on their competitive performance for toxic Cr (VI) removal

The current study focused on the comparative removal of hexavalent chromium using two magnetically modified hybrid adsorbent composites. Their precursor chars were prepared from bio sludge and plastic waste derivatives. The coating of magnetite on the chars' surface was evident from the SEM micrographs. Infusion of magnetite nanoparticles in the native chars aided in the reduction of the composite particles' sizes, thus, forming high surface area composites. Screening of uptake capacities among various blends of char and magnetite were surveyed. Composites of both kinds with a 1:5 ratio of char: iron salts composition answered well. The pH_ZPC and zeta potential values of the composites indicated the neutral charge on the composites' surface. This suggested the need for a highly acidic environment for efficient Cr(VI) removal. Optimum economic conditions for Cr(VI) removal were obtained from the batch studies (solution pH - 1.5; contact time - (a) MPC [magnetic plastic char] - 60 min (b) MBC [magnetic biochar] - 40 min; temperature - 25 °C). The maximum monolayer adsorption capacity of MPC and MBC were found to be 84.67 mg/g and 53.83 mg/g respectively. Isotherm, kinetic and thermodynamic studies revealed the adsorption systems' inclination towards physisorption. From the characterization and modeling results, electrostatic force of attraction and pore filling was anticipated to be the mechanism of adsorption for both MPC and MBC. Thus, in the relative removal studies, MBC was found to compete better than MPC due to its enhanced porosity and surface area.

Recent development of magnetic biochar crosslinked chitosan on heavy metal removal from wastewater - Modification, application and mechanism

Heavy metal contamination in water bodies is currently in an area of greater concern due to the adverse effects on human health. Despite the good adsorption performance of biochar, various modifications have been performed on the pristine biochar to further enhance its adsorption capability, at the same time overcome the difficulty of particles separation and mitigate the secondary pollution issues. In this review, the feasibility of chitosan-modified magnetic biochar for heavy metal removal from aqueous solution is evaluated by critically analysing existing research. The effective strategies that applied to introduce chitosan and magnetic substances into the biochar matrix are systematically reviewed. The physicochemical changes of the modified-biochar composite are expounded in terms of surface morphology, pore properties, specific surface area, surface functional groups and electromagnetism. The detailed information regarding the adsorption performances of various modified biochar towards different heavy metals and their respective underlying mechanisms are studied in-depth. The current review also analyses the kinetic and isotherm models that dominated the adsorption process and summarizes the common models that fitted well to most of the experimental adsorption data. Moreover, the operating parameters that affect the adsorption process which include solution pH, temperature, initial metal concentration, adsorbent dosage, contact time and the effect of interfering ions are explored. This review also outlines the stability of modified biochar and their regeneration rate after cycles of heavy metal removal process. Lastly, constructive suggestions on the future trends and directions are provided for better research and development of chitosan-modified magnetic biochar.

A systematic review on adsorptive removal of hexavalent chromium from aqueous solutions: Recent advances

The contamination of natural resources by hexavalent chromium (Cr(VI)) originating from natural and anthropogenic activities is a serious environmental concern. Although many articles on chromium remediation have been published, a comprehensive understanding of the mechanisms involved in remediation with different sorbents is not yet available. In this systematic review, the performance and applicability of several adsorptive materials for Cr(VI) removal from aqueous media are discussed, along with a detailed analysis of the mechanisms involved. Statistical analysis is applied to compare the efficacies of different adsorbents, while a similar approach is used to determine the effects of sorbent properties and experimental conditions on the adsorption capacity. A detailed analysis of the factors involved in fixed-bed column studies is also presented. A suitable desorption approach to the regeneration of the spent adsorbent and its adsorption performance in reuse is also examined. Among the different sorbents, nanoparticles and mineral-doped biochar were found to be the most effective sorbents, while the adsorption was higher at low pH (~4.0) than that at intermediate pH (6-8). Contrary to our expectation, adsorption was high for sorbents with low specific surface areas, suggesting that the adsorption of Cr(VI) is largely influenced by the chemical properties of the sorbents. The optimum adsorption in fixed-bed column systems is obtained at a lower Cr(VI) ion concentration, a lower influent flow rate, and a higher bed height. Since most of the studies reviewed herein were merely experimental and utilized ideal conditions with the presence of a single contaminant, i.e. Cr(VI) in water, further studies on adsorption dynamics with the presence of other interfering ions are suggested. This review is promising for the further development of Cr(VI) removal strategies and closes the research gaps pertaining to their challenges.

A critical review of biochar-based materials for the remediation of heavy metal contaminated environment: Applications and practical evaluations

The contamination of heavy metals (HMs) in the environment has aroused a global concern. The valid remediation of HM contaminated environment is a highly significant issue. As alternative to carbon materials, biochar has been vastly documented for the remediation of HM contaminated environment. However, there are some possible imperfections to meet the actual remediation tasks as the finite properties of raw biochar, and the remediation process is complex and unexpectedly. This review focuses on the progress made on environmental HM remediation by biochar-based materials within the past six years. The property analysis and key modifications of biochar are summarized inspired by their applicability or necessity for HM decontamination, and the environmental remediation as well as the implicated mechanisms are thoroughly elaborated from multiple pivotal sides. The evaluations of practical application associated with biochar amendment are also presented. Finally, some pertinent improvements and research directions are proposed. To our knowledge, this article is the first time to make a systematic summary on the reliability and practicability of biochar-based materials for environmental HM remediation, and critically pointed out the existing issues to facilitate the judicious design of biochar-based materials and understanding the research trends. It is also aims to provide reference for subsequent research and propel the practical applications.

Iron oxide nanoparticles doped biochar ameliorates trace elements induced phytotoxicity in tomato by modulation of physiological and biochemical responses: Implications for human health risk

Use of untreated municipal wastewater (WW) contains toxic trace elements that pose a serious threat to the soil-plant-human continuum. The use of biochar (BC) is a promising approach to minimize trace element induced toxicity in the ecosystem. Therefore, the present study aims to evaluate the efficacy of BC derived from wheat straw and iron oxide nanoparticles doped biochar (IO-BC) to reduce trace element buildup in soil and plants that consequently affect tomato plant growth and physiological activity under WW irrigation. The BC and IO-BC were applied at four levels (0, 0.5, 1, and 1.5%) in WW irrigated soils. The results indicated that the addition of WW + BC and WW + IO-BC resulted in significant reduction in trace element mobility in soil. Interestingly, the application of WW + IO-BC (1.5%) was more effective in reducing trace element mobility and bioavailability in soil by 78% (As), 58% (Cr), 46% (Pb) and 50% (Cd) compared to WW irrigation, and thus reduced trace element accumulation and toxicity in plants. Results revealed that WW irrigation negatively affected tomato growth, fruit yield, physiology and antioxidative response. Addition of WW + BC and WW + IO-BC ameliorated the oxidative stress (up to 65% and 58% in H₂O₂ and MDA) and increased plant tolerance (up to 49% in POD and APX activity). The risk indices also showed minimum human health risk (H1 < 1) from tomato after the addition of BC or IO-BC in WW irrigated soils. It is concluded that IO-BC addition in WW irrigated soil could assist in reducing trace elements accumulation and toxicity in tomato and associated human health risks.

Preparation of H3PO4 modified Sidr biochar for the enhanced removal of ciprofloxacin from water

In this study, biochar was prepared from Sidr plant leaves and used for the treatment of ciprofloxacin (CIP)-contaminated water. CIP is important class of emerging water pollutants from pharmaceutical industries. The biochar showed 65% adsorption efficiency and 43.48 mg/g adsorption capacity of CIP. Adsorption efficiency as well as adsorption capacity were improved to 91% and 62.50 mg/g, respectively, by phosphoric acid (H₃PO₄) modified biochar. Removal of CIP by the prepared biochar was due to different surface functional groups of CIP and biochar as revealed from the study of different characterization analyses. The presence of PO₄^3- group in modified biochar led to maximum binding of CIP. Also, the modified biochar showed higher reusability potential and less leaching of ions when compared to the raw biochar. Removal of CIP was affected by concentrations of CIP, the amount of biochar and different pH's; the maximum removal of CIP was achieved at pH 4. The Freundlich and pseudo-first-order models best fitted the removal of CIP by modified biochar. Advanced characterization techniques were applied to investigate surface and physiological characteristics of the biochar and modified biochar. The modification showed high impact on the performance and stability of biochar. The study showed significant impacts of modification on the potential of the biochar for treatment of CIP-contaminated water.

Efficient sequestration of lead from aqueous systems by peanut shells and compost: evidence from fixed bed column and batch scale studies

Lead (Pb) is a pervasive contaminant and poses a serious threat to living beings. The present study aims at batch and fixed bed column scale potential of commercial compost (CCB) and peanut shells biosorbents (PSB) for the sequestration of Pb from contaminated aqueous systems. The PSB and CCB were characterized with FTIR, SEM and Brunauer Emmett-Teller (BET) to get insight of the adsorption behavior of both materials. Fixed bed column scale experiments were performed at steady state flow (2.5 and 5.0 mL/min), initial Pb concentrations (25 and 50 mg/L) and dosage of each adsorbent (3.0 and 6.0 g/column). Columns packed (15.9 cm2) with PSB and CCB have revealed excellent adsorption of Pb with PSB as compared with CCB. The total volume of injected contaminated water was 1,500 mL and 3,000 mL at 2.5 and 5.0 mL/min, respectively while total bed volume number was 157. A series of batch experiments with CCB and PSB was conducted at adsorbent dosage (1.25–5.0 g/L), initial Pb level (25–100 mg/L), interaction time (0–180 min) and solution pH (4–10) at room temperature. Batch scale results revealed that PSB removed 92% Pb from water at 25 mg Pb/L concentration as compared with CCB (79%). The presence of competing ions in groundwater showed less Pb removal as compared with synthetic water. The experimental data were simulated with equilibrium isothermal models: Langmuir, Freundlich, and kinetic models: pseudo first order, pseudo second order and intra-particle diffusion. The Freundlich and pseudo second order models better described the equilibrium and kinetic experimental data, respectively with maximum sorption of 42.5 mg/g by PSB which is also evident from FTIR functional groups and SEM results. While equilibrium sorption of Pb onto CCB was equally explained by Freundlich and Langmuir models. These findings indicate that PSB could be an active and ecofriendly biosorbent for the sequestration of metals from contaminated aqueous systems.

Modified Activated Carbon for Copper Ion Removal from Aqueous Solution

Because of increasing environmental awareness, it is becoming more important to remove harmful elements from water solutions. This study used activated carbon (AC) derived from waste wood-based panels as the base material, oxidized with nitric acid (OAC), and grafted with iminodiacetic acid (IDA-OAC) to improve the adsorption capacity and affinity for metals. The characterization of AC, OAC, and IDA-OAC was conducted via FTIR, SEM, N2 adsorption and desorption analysis, elemental analysis, Boehm titration, and point of zero charge (PZC). The instrument studies proved the modified increasing of the functional groups of the adsorbents. Moreover, batch and column experiments were conducted to evaluate the ability of the three adsorbents to remove copper ions from aqueous solution. In batch sorption, IDA-OAC had the highest adsorption capacity (84.51 mg/g) compared to OAC (54.74 mg/g) and AC (24.86 mg/g) at pH 5. The breakthrough point (Ct/Ci = 0.05) of copper ions for IDA-OAC occurred much later than AC in the column experiment (AC = 19 BV, IDA-OAC = 52 BV). The Langmuir isotherm and pseudo-second-model kinetics modeling could better fit with the data obtained from the batch sorption of AC, OAC, and IDA-OAC. The significant capacity and reusability of IDA-OAC displayed high applicability for water treatment.

Biochar caged zirconium ferrite nanocomposites for the adsorptive removal of Reactive Blue 19 dye in a batch and column reactors and conditions optimizaton

Biochar caged zirconium ferrite (BC-ZrFe2O5) nanocomposites were fabricated and their adsorption capacity for Reactive Blue 19 (RB19) dye was evaluated in a fixed-bed column and batch sorption mode. The adsorption of dye onto BC-ZrFe2O5 NCs followed pseudo-second-order kinetics (R 2 = 0.998) and among isotherms, the experimental data was best fitted to Sips model as compared to Freundlich and Langmuir isotherms models. The influence of flow-rate (3–5 mL min−1), inlet RB19 dye concentration (20–100 mg L−1) and quantity of BC-ZrFe2O5 NCs (0.5–1.5 g) on fixed-bed sorption was elucidated by Box-Behnken experimental design. The saturation times (C t /C o  = 0.95) and breakthrough (C t /C o  = 0.05) were higher at lower flow-rates and higher dose of BC-ZrFe2O5 NCs. The saturation times decreased, but breakthrough was increased with the initial RB19 dye concentration. The treated volume was higher at low sorbent dose and influent concentration. Fractional bed utilization (FBU) increased with RB19 dye concentration and flow rates at low dose of BC-ZrFe2O5 NCs. Yan model was fitted best to breakthrough curves data as compared to Bohart-Adams and Thomas models. Results revealed that BC-ZrFe2O5 nanocomposite has promising adsorption efficiency and could be used for the adsorption of dyes from textile effluents.

Natural pyrite improved steel slag towards environmentally sustainable chromium reclamation from hexavalent chromium-containing wastewater

Currently, varied processes adopted to remove hexavalent chromium from aqueous solution have been realized to cause secondary pollution. As such, this study explored a green method for aqueous hexavalent chromium (Cr(Ⅵ)) reclamation by waste steel slag (SS) enhanced by natural pyrite (NP). Compared with the sole SS or NP, more efficient Cr(Ⅵ) removal was achieved by NP-SS at an initial pH value ranging from 1 to 8, resulting in a final pH value of 7-8. Cr(Ⅵ) in the solution could be initially reduced to Cr(III) by Fe²⁺ provided by NP, which was then bound with the OH^- in the solution and the supersaturated calcium silicate hydrate on the surface of SS. In addition, the stearic acid anions existing on the surface of SS could promote the adsorption of Cr(III) to form chromium stearate. The used adsorbent could be potentially used for chromium smelting. Overall, this study provides a feasible and environmental sustainable solution to chromium reclamation from hexavalent chromium-containing wastewater.

Removal of Cu2+ metal ions from water using Mg-Fe layered double hydroxide and Mg-Fe LDH/5-(3-nitrophenyllazo)-6-aminouracil nanocomposite for enhancing adsorption properties

Herein, a new adsorbent was prepared by modifying Mg-Fe LDH for the removal of Cu²⁺ metal ions from wastewater. Mg-Fe LDH with 5-(3-nitrophenyllazo)-6-aminouracil ligand has been successfully prepared using direct co-precipitation methods and was fully characterized using FTIR analysis, X-ray diffraction, BET surface area theory, zeta potential, partial size, TGA/DTA, CHN, EDX, FESEM, and HRTEM. The surface areas of Mg-Fe LDH and Mg-Fe LDH/ligand were 73.9 m²/g and 34.7 m²/g respectively. Moreover, Cu²⁺ adsorption on LDH surfaces was intensively examined by adjusting different parameters like time, adsorbent dosage, pH, and Cu²⁺ metal ion concentration. Several isotherm and kinetic models were investigated to understand the mechanism of adsorption towards Cu²⁺ metal ions. Adsorption capacity values of LDH and ligand-LDH rounded about 165 and 425 mg/g respectively, applying nonlinear fitting of Freundlich and Langmuir isotherm equations showing that the ligand-LDH can be considered a potential material to produce efficient adsorbent for removal of heavy metal from polluted water. The adsorption of Cu²⁺ metal ions followed a mixed 1,2-order mechanism. The isoelectric point (PZC) of the prepared sample was investigated and discussed. The effect of coexisting cations on the removal efficiency of Cu²⁺ ions shows a minor decrease in the adsorption efficiency. Recyclability and chemical stability of these adsorbents show that using Mg-Fe LDH/ligand has an efficiency removal for Cu²⁺ ions higher than Mg-Fe LDH through seven adsorption/desorption cycles. Moreover, the recycling of the Cu²⁺ ions was tested using cyclic voltammetry technique from a neutral medium, and the Cu²⁺ ion recovery was 68%.

Adsorption of Cr(VI) onto cross-linked chitosan-almond shell biochars: equilibrium, kinetic, and thermodynamic studies

In this study, to remove Cr(VI) from the solution environment by adsorption, the almond shell was pyrolyzed at 400 and 500 °C and turned into biochar (ASC400 and ASC500) and composite adsorbents were obtained by coating these biochars with chitosan (Ch-ASC400 and Ch-ASC500). The resulting biochars and composite adsorbents were characterized using Fourier transform infrared (FTIR) spectroscopy; Brunauer, Emmett, and Teller (BET) surface area; scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX); and the point of zero charge pH (pHpzc) analyses. The parameters affecting the adsorption were examined with batch adsorption experiments and the optimum parameters for the efficient adsorption of Cr(VI) in 55 mg L−1 solution were determined as follows; adsorbent dosages: 5 g L−1 for biochars, 1.5 g L−1 for composite adsorbents, contact time: 120 min, pH: 1.5. It was seen that the temperature did not affect the adsorption much. Under optimum conditions, Cr(VI) adsorption capacities of ASC400, ASC500, Ch-ASC400, and Ch-ASC500 adsorbents are 11.33, 11.58, 37.48, and 36.65 mg g−1, respectively, and their adsorption percentages are 95.2%, 97.5%, 94.3%, and 94.0%, respectively. Adsorption data were applied to Langmuir, Freundlich, Scatchard, Dubinin-Radushkevic, and Temkin isotherms and pseudo-first-order kinetic model, pseudo-second-order kinetic model, intra-particle diffusion model, and film diffusion model. The adsorption data fitted well to the Langmuir isotherm and pseudo-second-order kinetic models. From these results, it was determined that chemical adsorption is the dominant mechanism. Also, both intra-particle diffusion and film diffusion is effective in the adsorption rate. For all adsorbents, the Langmuir isotherm proved to be the most appropriate model for adsorption. The maximum monolayer adsorption capacities calculated from this model are 24.15 mg g−1, 27.38 mg g−1, 54.95 mg g−1, and 87.86 mg g−1 for ASC400, ASC500, Ch-ASC400, and Ch-ASC500, respectively. The enthalpy change, entropy change, and free energy changes during the adsorption process were calculated and the adsorption was also examined thermodynamically. As a result, adsorption occurs spontaneously for all adsorbents.

Adsorption of arsenic (III) from aqueous solution by a novel phosphorus-modified biochar obtained from Taraxacum mongolicum Hand-Mazz: Adsorption behavior and mechanistic analysis

A novel phosphorus (P) modified biochar (PLBC) was produced by pyrolyzing biomass of the dietic herb Taraxacum mongolicum Hand-Mazz (TMHM) and treating it with monopotassium phosphate (KH₂PO₄). This phosphorous loaded biochar was then assessed as adsorbent for As(III) removal from contaminated water. In the current research, the adsorbent was characterized before and after P loading by means of SEM-EDX, TEM, FTIR and XRD techniques. It was evidenced that the presence of P on the surface of the biochar (BC) could improve its efficiency to remove As(III) from contaminated environments. Adsorption kinetics were evaluated by performing batch-type experiments at varied times and pH values (5, 7 and 9). The kinetic study revealed that a contact time of 24 h was required to attain equilibrium and the experimental data were best fitted to the pseudo-second-order kinetic model (q_e = 17.1 mg g^-1). In addition, several batch experiments were conducted with varied arsenic concentrations. During the adsorption tests, the maximum adsorption of As(III) was found at pH 5. The adsorption study further showed that compared to BC, PLBC depicted increased removal of As(III) from contaminated solutions. The adsorption experimental data showed the best fit to the Langmuir isotherm model (with R² = 0.84), with maximum As(III) adsorption capacity reaching 30.76 mg g^-1 for PLBC.

Java plum and amaltash seed biomass based bio-adsorbents for synthetic wastewater treatment

Biomass of Java plum (JP) and amaltash (AT) seeds were employed to remove arsenic from synthetic wastewater, cost effectively. The prepared biomasses were characterized by FE-SEM, EDX, FTIR, XRD, and ICP techniques. Experimentation the optimization study has been carried out by using Design-software 6.0.8. Response surface methodology has been applied to design the experiments where we have used three factors and three levels Box-Behnken design (BBD). Arsenic removal ability of bio-sorbents was evaluated and optimized by varying pH, adsorbent dose concentration of arsenic in synthetic wastewater. For 2.5 mg/L arsenic concentration and 80 mg adsorbent dose at pH 8.8 Java plum seeds (JP) based bio-adsorbent removed ∼93% and amaltash seeds (AT) based bio-adsorbent removed ∼91% arsenic from synthetic wastewater. The adsorption behaviour better explained following Freundlich model (R² = 0.99) compared to Temkin model (R² = 0.986) for As (III) ions. The adsorption capacity was 1.45 mg g^-1 and 1.42 mg g^-1 for JP and AT, respectively after 80 min under optimal set of condition. The adsorption kinetics was explained by either pseudo-first order model or Elovich model.

Adsorption of Co(II) from aqueous solution using municipal sludge biochar modified by HNO3

Here adsorption studies were proposed on a carboxylated sludge biochar (CSB) material modified by HNO₃ to assess its capacity in the removal of cobalt from aqueous solution. The as-prepared sludge biochar material was characterized by Brunauer-Emmett-Teller (BET) analysis, Fourier transform infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA), energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The isotherm process could be well described by the Langmuir isotherm model. The adsorption kinetics indicated that cobalt adsorption followed a pseudo-second-order kinetics model. The mechanism between Co(II) and biochar involved electrostatic interaction, ion exchange, surface complexation and physical function. The adsorption capacity on CSB was as high as 72.27 mg·g^-1, surpassing original sludge biochar (SB) as CSB had abundant oxygen-containing functional groups and many hydroxyls, plus the BET surface areas increased when SB was modified by HNO₃, which stimulated adsorption effect. Therefore, this work shows that CSB could be used as an efficient adsorbent to remove Co(II) in wastewater.

Chemical processes of Cr(VI) removal by Fe-modified biochar under aerobic and anaerobic conditions and mechanism characterization under aerobic conditions using synchrotron-related techniques

Fe-modified biochar (FeBC) has been considered for aqueous hexavalent chromium (Cr(VI)) removal, but a better understanding is needed with respect to the removal behavior, chemical processes, and removal mechanisms under aerobic and anaerobic conditions. Aqueous Cr(VI) removal was evaluated using unmodified (BC) and FeBC. The Cr(VI) was completely removed in a pH range of 2-10. The removal behavior was properly depicted using pseudo-second-order (PSO) and Langmuir models under aerobic conditions, and using PSO and Freundlich models under anaerobic conditions. Removal rate and capacity were enhanced by up to 3.8 times under anaerobic conditions. Desorption experiments indicated removed Cr in FeBC was stable except under strong acid condition. X-ray absorption spectroscopy (XAS) analysis suggested removed Cr in FeBC was 100% in Cr(III) form and bound to Fe with a bond length of 3.01 Å in the stable form of Fe(III)_nCr(III)_(1-n)(OOH). The removal mechanisms of Cr(VI) under aerobic conditions by FeBC mainly included electrostatic adsorption, chemical reduction, and complex precipitation.

Magnetic biochars have lower adsorption but higher separation effectiveness for Cd2+ from aqueous solution compared to nonmagnetic biochars

Magnetic biochars were prepared by chemical co-precipitation of Fe³⁺/Fe²⁺ onto rice straw (M-RSB) and sewage sludge (M-SSB), followed by pyrolysis treatment, which was also used to prepare the corresponding nonmagnetic biochars (RSB and SSB). The comparison of adsorption characteristics between magnetic and nonmagnetic biochars was investigated as a function of pH, contact time, and initial Cd²⁺ concentration. The adsorption of nonmagnetic biochars was better described by pseudo-second-order kinetic model, and the adsorption of RSB and SSB was better described by Langmuir and Freundlich models, respectively. Magnetization of the biochars did not change the applicability of their respective adsorption models, but reduced their adsorption capabilities. The maximum capacities were 42.48 and 4.64 mg/g for M-RSB and M-SSB, respectively, underperforming their nonmagnetic counterparts of 58.65 and 7.22 mg/g for RSB and SSB. Such a reduction was fundamentally caused by the decreases in the importance of cation-exchange and Cπ-coordination after magnetization, but the Fe-oxides contributed to the precipitation-dependent adsorption capacity for Cd²⁺ on magnetic biochars. The qualitative and quantitative characterization of adsorption mechanisms were further analyzed, in which the contribution proportions of cation-exchange after magnetization were reduced by 31.9% and 12.1% for M-RSB and M-SSB, respectively, whereas that of Cπ-coordination were reduced by 3.4% and 31.1% for M-RSB and M-SSB, respectively. These reductions suggest that for adsorbing Cd²⁺ the choice of conventional biochar was more relevant than whether the biochar was magnetized. However, magnetic biochars are easily separated from treated solutions, depending largely on initial pH. Their easy of separation suggests that magnetic biochars hold promise as more sustainable alternatives for the remediation of moderately Cd-contaminated environments, such as surface water and agriculture soil, and that magnetic biochars should be studied further.

Preparation of magnetic biochar and its application in catalytic degradation of organic pollutants: A review

In recent years, magnetic biochar (MBC) has been greatly concerned because of its magnetic separation characteristics, and has been successfully used as a catalyst in the catalytic degradation of organic pollutants. However, there is currently a lack of a more systematic summary of MBC preparation methods, and no detailed overview of the catalytic mechanism of MBC catalysts for the degradation of organic pollutants. Therefore, we carry out this work to fill the above gaps. At first, we summarize the raw materials, preparation methods, and types of MBC in detail, and emphasize the MBC prepared by iron-containing sludge. Then, the catalytic mechanisms of MBC in peroxydisulfate, peroxymonosulfate, Fenton-like, photocatalysis, and NaBH₄ systems are carefully summarized, highlighting the contribution of various parts of MBC in catalysis. The degradation efficiency of organic pollutants in the above systems is evaluated. Finally, the stability and reusability of MBC catalysts are evaluated. In conclusion, this review contributes a meager force to the future development of MBC.

Self-propagating synthesis of Zn-loaded biochar for tetracycline elimination

Herein, a novel Zn-loaded biochar (Zn-LBC) originating from Fraxinus pennsylvanica Marsh leaves was successfully prepared through a simple and rapid self-propagating combustion reaction (SHS) and could serve as an efficient adsorbent for tetracycline (TC) elimination from water. The adsorption performance was analyzed via a series of characterizations and batch adsorption experiments. The results showed that the novel adsorbent Zn-LBC exhibited an excellent TC adsorption capacity (159.64 mg/g), which was 2.63 times higher than that of the original biochar (60.78 mg/g). The pseudo-second-order kinetic model and Freundlich isothermal model fit the adsorption data well. It is noteworthy that Zn-LBC had little effect on the adsorption capacity of TC in the 0-10 mg/L various coexisting ion range and presence of humic acid (HA). In addition, the adsorption test of TC using hospital wastewater as the water sample also achieved satisfactory results (raw influent: 52.65 mg/g, final effluent: 85.64 mg/g). FT-IR and XPS investigations showed that the TC adsorption mechanism included surface complexation, π-π interactions, and hydrogen bonds. The results provide new ideas for exploring low-cost and highly efficient modified biochar adsorbent for TC elimination.

Coconut shell derived ZnCl2 activated carbon for malachite green dye removal

The coconut-based agricultural wastes have gained wide attention as an alternative adsorbent for the removal of diverse pollutants from the industrial effluents. This paper presents the zinc chloride activation of adsorbent carbon and the utilization as an adsorbent for the removal of malachite green dye from aqueous solution. The characterisation of activated carbon was performed to get an insight into the adsorption mechanism. The ZnCl₂ activated carbon acquired a higher specific surface area (544.66 m² g^-1) and stability (-32.6 mV). The impact of process parameters including contact time (20-220 min) and initial dye concentration (20-80 mg L^-1) were evaluated on the effectiveness of activated carbon for dye removal. The results concluded that zinc chloride activated carbon showed a significant dye adsorption (39.683 mg g^-1) at an initial concentration of 20 mg L^-1 after 3 hours. Based on the correlation coefficient (R²), the Freundlich isotherm model (0.978-0.998) was best fitted for the experimental data followed by the intraparticle diffusion model (0.88-0.929) as the most appropriate model for malachite green dye removal. Additionally, the energy and thermogravimetric analysis portrayed the suitability of the carbon material to be used as an energy alternative to coal.

Nano-zerovalent manganese/biochar composite for the adsorptive and oxidative removal of Congo-red dye from aqueous solutions

Congo-red (CR), a precursor of textile products and a contaminant of great concern, has contaminated aquatic environments. Here, we explored the synthesis of mesoporous nano-zerovalent manganese (nZVMn) and Phoenix dactylifera leaves biochar (PBC) composite for the removal of CR from water. The nZVMn/PBC adsorbed 117.647 mg/g of CR versus 25.316 mg/g by PBC at [CR]₀ = 20 mg/L and [PBC]₀ = [nZVMn/PBC]₀ = 500 mg/L. Variation of [nZVMn/PBC]₀, [CR]₀ and pH influenced the adsorption of CR. Freundlich adsorption isotherm and pseudo-first-order kinetic models best fitted CR adsorption. The H₂O₂ coupling with nZVMn/PBC promoted removal of CR possibly due to the formation of hydroxyl radical (^●OH) and caused 95 % removal of CR versus 77 % by nZVMn/PBC alone. The ^●OH scavengers inhibited the removal of CR. The nZVMn/PBC showed a good reusability and efficient removal of CR up to the seventh cycle of treatment. Results reveal that nZVMn improved performance, thermal stability and reusability of biochar. Degradation products from ^●OH-mediated degradation of CR were studied by ultraperformance liquid chromatography with mass spectrometric detector to establish degradation pathways. The ion-chromatographic analysis showed the formation of non-toxic inorganic acetate product, which suggests high potential of the newly fabricated adsorbent in the removal of CR.

Activated carbon-alginate beads impregnated with surfactant as sustainable adsorbent for efficient removal of methylene blue

A cost-effective and sustainable Calligonum polygonoides biomass based activated carbon (AC) was synthesized. The prepared AC was utilized in the fabrication of carbon-alginate beads for the adsorption of methylene blue (MB) textile dye from aqueous solution. The surface morphology, surface functional groups, elemental analysis and thermal behavior of the prepared beads were investigated using different analytical techniques. Batch adsorption experiments were performed to investigate the adsorption capacity of the beads. Effect of different parameters such as initial pH of MB solution, dose of adsorbent, contact time, initial concentration of MB and temperature were evaluated. The kinetic studies identified pseudo-second order model. Langmuir and Freundlich isotherm models were applied and fitted to the experimental equilibrium data. The beads showed a maximum adsorption capacity of 769 mg/g in basic pH at 30 °C while using 400 mg·L^-1 of MB solution. The adsorption process was found to be endothermic and spontaneous as confirmed by the thermodynamic data. The fabricated beads were subjected to recycling which exhibited same adsorption efficiency after six regeneration cycles. The results showed that the AC-alginate beads impregnated with SDS have high adsorption capability and would be used for the efficient removal of cationic dyes from wastewater.

Hydrochar and pyrochar for sorption of pollutants in wastewater and exhaust gas: A critical review

Pollutants in wastewater and exhaust gas bring out serious concerns to public health and the environment. Biochar can be developed as a sustainable adsorbent originating from abundant bio-wastes, such as agricultural waste, forestry residue, food waste and human waste. Here we highlight the state-of-the-art research progress on pyrochar and hydrochar for the sorption of pollutants (heavy metal, organics, gas, etc) in wastewater and exhaust gases. The adsorption performance of pyrochar and hydrochar are compared and discussed in-depth, including preparation procedures (carbonization and activation), sorption possible mechanisms, and physiochemical properties. Challenges and perspective for designing efficient and environmental benign biochar-based adsorbents are finally addressed.

Facile preparation of sulfonated biochar for highly efficient removal of toxic Pb(II) and Cd(II) from wastewater

Biochar is deemed as the ideal material for the effective removal of heavy metals in wastewater treatment. Herein, we developed a facile one-step solvothermal method for the preparation of sulfonated biochar (SBC) from Axonopus compressus under a low-temperature condition. FTIR and XPS analysis demonstrate that plenty of -OH, -COOH and -SO₃H moieties are generated on the surface of SBC during the sulfonation process. Due to high electronegativity and strong complexation of these moieties, SBC can rapidly adsorb Pb(II) and Cd(II) with capacities of 191.07 and 85.76 mg/g respectively within 5 min. SBC can be reused for 5 cycles with a negligible loss of adsorption capacity. In addition, different biomass-based biochars are prepared under the identical experimental conditions, and they are successfully applied in the treatments of Pb(II) and Cd(II). The satisfying results indicate that one-step low-temperature sulfonation could be a universal method, and various types of biomass waste could be the abundant, effective, economical material source for the treatment of environmental heavy metal pollution in future.

Nonlinear regression analysis and response surface modeling of Cr (VI) removal from synthetic wastewater by an agro-waste Cocos Nucifera: Box-Behnken Design (BBD)

In this study mixture of coconut shell and coir was used for Cr (VI) removal from synthetic wastewater and statistical tool Response Surface Modeling (RSM) was applied to optimize process parameters. The solution pH (2-6), reaction time (20-100 minutes) and adsorbent quantity (0.03-0.2 g) was optimized to find the maximum response of Cr (VI) removal using statistical Box-Behnken design (BBD) software. The equilibrium data obtained by the batch experiment were analyzed by ANOVA and found fitted in a second-order polynomial equation through multiple regression analysis. The optimum value of pH, adsorbent quantity and reaction time for 99% of Cr(VI) was found as 2, 0.1 g and 100 minutes, respectively. By using non-linear regression method it was found that Freundlich isotherm and Pseudo-second-order kinetic with high correlation coefficient (R²), low Chi-square (χ²) and root mean squares errors (RMSE), best describe the adsorption of Cr (VI) on mixture of coconut shell and coir (MCSC) surface. Positive enthalpy (ΔH°) and negative Gibbs free energy (ΔG^o) values confirm the endothermic and spontaneous nature of adsorption process. Pre and post adsorption phenomenon was confirmed by characterization of adsorbent using AFM, FTIR, SEM, and EDX analysis. The adsorbent MCSC has regenerative property and can be reused 3-4 times after treating with alkaline medium (0.2 N NaOH) and offered more than 60% removal of Cr (VI) at the fourth cycle. It can be inferred based on this study that MCSC is an effective adsorbent for Cr (VI) removal and can be used on an industrial scale for social and environmental benefit. Novelty statement An agriculture waste mixture of coconut shell and coir (MCSC) without the addition of any chemical reagent, was used for Cr(VI) removal. As per literature survey and best of our knowledge, the adsorbent MCSC has not been reported for Cr (VI) removal. In the previous study, authors reported either coconut coir pith or coconut shell or coconut charcoal as adsorbent for Cr (VI) removal. The adsorbent MCSC is efficient even at very low doses (0.1 g) as compared to the reported adsorbent.

Influence of Synthesis Methods on the High-Efficiency Removal of Cr(VI) from Aqueous Solution by Fe-Modified Magnetic Biochars

Fe-modified biochars have been widely used in removal of Cr(VI) from water due to the resulting modified surface functional groups and magnetization property. However, few studies have synthetically investigated modification methods and synthesis parameters on the improvement of the removal efficiency of Cr(VI) by Fe-modified biochars. Herein, 10 types of corn straw-based magnetic biochars were produced using pre-modification and post-modification methods with various modifier ratios, and the highest heating temperature (HHT). Cr(VI) removal results suggest that the removal efficiency of pre-modified biochars ranged from 50.7 to 98.6%, which was much higher than that of post-modified (6.6-21.6%) and unmodified biochars (0.4-7.6%). The effect of synthesis methods on Cr(VI) adsorption was in the following order: Fe-modification method > modifier ratio > HHT. The adsorption kinetics and isotherm results of three types of pre-modified biochars were well fitted with the pseudo-second-order model (R ² > 0.99) and the Langmuir adsorption model (R ² > 0.99), respectively, indicating the surface homogeneity of the pre-modified biochars and unilayer chemisorptions of Cr(VI). Characterization results show that iron oxides or zerovalent iron particles were successfully deposited onto the surface of biochars and magnetism was introduced. A good Pearson correlation (r = -0.9694) between the removal efficiency and pH value in modified biochar suggests that the lower pH value may offer more positive charges and promote electrostatic attraction. Therefore, the dominant mechanism for enhanced Cr(VI) adsorption on pre-modified biochar was electrostatic attraction, resulting from its distinguished acidity nature. Our findings provide new insights into the high-efficiency removal of Cr(VI) onto Fe-modified magnetic biochars and will benefit future design of more efficient magnetic biochars.

Effective sequestration of Cr (VI) from wastewater using nanocomposite of ZnO with cotton stalks biochar: modeling, kinetics, and reusability

The disposal of chromium (Cr) containing wastewater in surface water bodies without prior treatment is a serious threat to humans, animals, and plants. A novel nanocomposite (CSB/ZnO) of cotton stalks biochar (CSB) with ZnO nanoparticles was synthesized for the removal of Cr (VI) ions from contaminated water at batch scale. The impact of adsorbent dosage (1-4 g/L), initial Cr (VI) levels (25-200 mg/L), pH (2-8), and interaction time (0-180 min) was assessed for the removal of Cr (VI) from contaminated water. The Fourier-transform infrared (FTIR), scanning electron microscopy (SEM), and point of zero charge (PZC) characterization showed successful impregnation of ZnO particles on CSB with improved surface characteristics. The maximum adsorption (qmax) of CSB and CSB/ZnO was 54.95 and 107.53 mg Cr/g, respectively that is relatively higher than various previously studied adsorbents. The experimental isothermal data better fitted with the Freundlich model in comparison with other isotherm models while adsorption kinetics well corroborated with the pseudo-second-order model. The results revealed that doping of biochar with metallic nanoparticles (CSB/ZnO) proved very effective (99.6% at 50 mg/L) with high reusability (91%) after five adsorption/desorption cycles and seems a suitable strategy for the decontamination of Cr (VI) contaminated waters.