Lifetime prediction of biodegradable polymers

Nanoplastics and microplastics released from an enzyme-embedded biodegradable polyester during hydrolysis

Embedding enzyme in biodegradable polyester accelerates hydrolysis in environments it ends up, but the release of microplastics (MPs) and nanoplastics (NPs) during this process remains underexplored. This work investigated the evolution of MPs and NPs released from poly(ε-caprolactone) (PCL) with embedded Lipase PS. The embedded enzyme significantly accelerated hydrolysis, causing the PCL film to disappear within 96 h. Notably, the formation rates and quantities of MPs and NPs were much higher compared to film with external enzyme. At 96 h, MPs (3.55 ×105 particles/mL) was 2.4 times, and NPs (4.65 ×107 particles/mL) was an order of magnitude higher than that with external enzyme. After 130 days, although both quantities and average size of MPs and NPs decreased due to only 90.6 % of enzymes were detected leaking, they did not completely disappear. The quantities of MPs and NPs were comparable to that with external enzyme, and the average size of MPs remained 1 μm. The simultaneous erosion inside film macroscopically, and severe chain cleavage microscopically, contributed to feasible film disintegration and formation of high amounts MPs and NPs. These findings underscore the importance of managing the release of MPs and NPs during the hydrolysis of enzyme-embedded biodegradable polyesters to ensure safety and mitigate environmental impact.

Rayon fibre rope: A biodegradable alternative for marine use?

Rayon fibres are well-known materials that were primarily utilised as reinforcement in tyres. Today these materials are perceived as a promising substitute for synthetic fibres, exhibiting good mechanical characteristics and biodegradation in many environments. This paper investigates their potential use for marine structures. It first describes the tensile properties of the fibres and their derived yarns and ropes. These properties are then monitored during seawater ageing and the ultimate biodegradation is characterised by respirometry tests. Both material scales demonstrate rapid degradation rates under biotic conditions (90 % strength reduction after 2 weeks for yarns and 6 months for small ropes) and a relative stability in abiotic conditions. Additionally, the fibres show rapid bio-assimilation rates. The rope construction is demonstrated to have a significant impact on the degradation kinetics, suggesting possible strategies to enhance durability. The results indicate that these rayon fibre ropes may offer an attractive alternative to synthetic fibre ropes to reduce impact where there is a high risk of rope loss at sea.

A new tool to screen biodegradable polymers as technically and commercially viable fertiliser coatings

Polymer coated controlled release fertilisers can mitigate nutrient pollution by aligning nutrient release to plant demand, thereby reducing losses, fertiliser application and potentially increasing yields. However, most current commercial products use polymers that do not readily degrade. This use of non-degradable plastics to coat fertilisers is being phased out, opening new opportunities to develop and commercialise truly biodegradable coating alternatives. However, the technical challenge is substantial. The coating needs to eventually fully mineralise, leaving no microplastic legacy, yet it must also maintain good mechanical and barrier properties for extended periods. This work presents the first effort to develop a polymer material selection tool to guide biodegradable polymer selection for use as fertiliser coatings based on the polymers' known properties and commercial considerations. Using a new mechanistic model, a relationship was established between the elongation required to avoid coating rupture and the water vapour permeability (WVP) of the coating. Then, a broad list of commercially available biodegradable polymers was assembled and literature data on their WVP and elongation at break collated. By comparing this data and the model outcomes, the polymers most likely to achieve long term release were shortlisted. This list was further condensed by setting a maximum polymer price and minimum global production capacity for commercial viability. We have shortlisted polycaprolactone, biodegradable polyurethane and natural rubber as strong candidates for biodegradable fertiliser coatings. However, their rate of biodegradation requires further investigation. Flexible polyhydroxyalkanoates, poly(butylene succinate) and poly(propylene carbonate) are technically promising, but not currently commercially viable.

PLGA-based long-acting injectable (LAI) formulations

Long-acting injectable (LAI) formulations, which deliver drugs over weeks or months, have been in use for more than three decades. Most clinically approved LAI products are formulated using poly(lactide-co-glycolide) (PLGA) polymers. Historically, the development of PLGA-based LAI formulations has relied predominantly on trial-and-error methods, primarily due to a limited understanding of the complex factors involved in LAI formulations and insufficient analytical techniques available for characterizing individual PLGA polymers of the prepared formulations. This article offers a personal perspective on recent advancements in characterization methods for PLGA polymers within final formulations, i.e., products, as well as enhanced insights into the drug release mechanisms associated with LAI products. With a deeper understanding of PLGA polymer properties and drug release mechanisms, the formulation development process can transition from traditional trial-and-error practices to a more systematic Quality by Design (QbD) approach. Additionally, this article explores the emerging role of artificial intelligence (AI) in formulation science and its potential, when applied carefully, to enhance the future development of PLGA-based LAI formulations.

Supramolecular interaction-enhanced green active packaging films: Design and performance of Ca2+-crosslinked carboxymethyl chitosan composite films

Given the environmental challenges caused by petroleum-based plastics, this study developed a novel green carboxymethyl chitosan (CMCS)-based active packaging composite film (CP) through a synergistic strategy of precise Ca2+ coordination cross-linking and small-molecule plasticizing. Based on this strategy, the CP-4.5 film (CaCl2: 7 wt%, DL-3-phenyllactic acid (3-PLA): 4.5 wt%) exhibited exceptional mechanical properties, including high flexibility (Young's modulus: 0.747 GPa; elongation at break: 65.2 %) and high toughness (18.4 MJ m-3). The incorporation of CaCl2 not only occupied voids within the CP film but also increased the physical cross-linking strength and density of the polymer network. This structural reorganization impeded the diffusion of O2 and H2O molecules, reducing oxygen permeability by 85.9 % and water vapor permeability by 57.6 %. Additionally, 3-PLA, functioning as a broad-spectrum antibacterial agent, imparted the CP film with superior antibacterial activity. The CP film exhibited recyclability and repairability, and underwent complete biodegradation within 56 days. Overall, the synergistic effect of CaCl2 and 3-PLA endowed the CP film with superior mechanical properties, barrier properties, antimicrobial activity, and environmental sustainability, effectively mitigating the quality deterioration of refrigerated grass carp fillets during storage, demonstrating the promising potential of the CP film for food packaging applications.

Effects of bioplastics and their leachates on marine bacterial communities

Biobased biodegradable plastics (bioplastics) are promising alternatives fuel-based plastics. However, higher additive content is generally used to perform similarly to fuel-based materials. Moreover, plastic additives are not covalently bound to carbon chains and can leach into aquatic environments such as seawater, potentially impacting marine biota, though the extent of these effects is not yet fully understood. To evaluate the leaching behaviour in seawater of plastic additives from bioplastics materials and its impact on coastal surface marine bacterial communities, microcosm experiments were conducted using seawater amended with non-aged pellets of polylactic acid (PLA), poly-hydroxybutyrate (PHB), and commercial materials, a knife of PLA and a bag of PLA&PHB, under biotic and abiotic conditions for two months. Samples were taken weekly to study the bacterial abundance, bi-weekly to evaluate the leaching process and potential biodegradation products and, finally, at the end of the experiment to study the microbial communities. Chemical analysis was performed using suspect screening by means of Liquid Chromatography coupled to High-Resolution Mass Spectrometry (LCHRMS) equipped with Electrospray Ionization source working in positive and negative conditions. The experiment showed that 177 compounds were tentatively identified at confidence level 2, including plasticizers, UV filters, flame retardants, and PLA- and PHB-related degradation products, which were detected in similar proportions under abiotic and biotic processes. Bacterial communities exposed to PLA showed higher production and significant differences in the community composition, with PLA degraders being identified in the different plastispheres studied. Leachates impacted differently microbial communities in the free-living fraction, particle-attached fraction and in the plastisphere, indicating taxa-specific responses. To the best of our knowledge, this is the first study providing further insights into the influence of bioplastics and their leachates on marine microbial communities, contributing to our understanding of bioplastics' effects on the global oceans.

Carbon cycle of polyhydroxyalkanoates (CCP): Biosynthesis and biodegradation

Carbon neutrality of bioactive materials is vital in promoting sustainable development for human society. Polyhydroxyalkanoates (PHAs) is a class of typical carbon-cycle bio-polyesters synthesized by microorganisms using sugars, organic acids, and even carbon dioxide. PHAs first degrade into 3-hydroxybutyrate (3HB) before further breaking down into carbon dioxide and water, aligning with carbon-neutral goals. Due to their diverse molecular structures and material properties, excellent biocompatibility, and controlled biodegradability, PHAs have found widespread applications in environmental protection and biomedicine. However, challenges persist in achieving cost-effective PHA production and reusing degradation products. Additionally, understanding the carbon pathways in PHA synthesis and degradation remains limited. In this review, we first introduce the concept of the Carbon Cycle of Polyhydroxyalkanoates (CCP) and describe the biosynthetic pathways of aromatic monomers, carbon conversion processes, and PHA degradation in compost, soil, and marine environments. This will help us fully understand the sustainable utilization value of PHA as a biomaterial. Future trends point to integrating synthetic biology with emerging technologies to produce low-cost, high-value PHAs, supporting global green and low-carbon development.

Non-fuel applications of bio-oil for sustainability in management of bioresources

Biomass valorization by thermochemical conversion method is a promising and intriguing pathway due to the flexibility of utilizing a diverse group of biomass and biowastes, specific product delivery mechanism through manipulation of process parameters, and wide applicability of the products. Pyrolysis has been viewed as an effective valorization technique to transform biowastes into pyrolytic oil, solid char, and syngas. Syngas is generally fed to the pyrolysis process to generate heat necessary for the pyrolysis process to sustain. Pyrolysis may also be a subsidiary component in a biorefinery system where it draws feedstocks from refinery process residues or the side streams of the refinery operation. In recent times, pyrolysis products have been under intense research for their usability and diverse applicability. Bio-oil's rich chemical makeup has promising potential to be used as an advanced biofuel and is considered as a storehouse of diverse chemical species ranging from green solvents to bioactive chemicals. The current review provides a state of knowledge on non-fuel uses of bio-oil and concludes that the pyrolysis process and products could be a part of the future bioeconomy if designed in a manner that biowastes are transformed into value-added products which replace products of petroleum origin.

Microbially degradable phenolic foams based on depolymerized Kraft lignin for hydrophilic applications

Hydrophilic phenol-formaldehyde (PF) foams, widely used in floral and hydroponic applications, are produced using phenol typically derived from non-renewable petroleum-based resources. This study examines the potential of depolymerized Kraft lignin (DKL) as a sustainable substitute for phenol in the synthesis of hydrophilic biobased foams. At 50 % DKL substitution, the foams demonstrated excellent water absorption capacities (up to 2557 %), relatively low densities (∼62 kg/m3), and nearly 100 % open-cell content. Its compressive strength (20.64 kPa at 10 % deformation) is comparable to commercially available floral and hydroponic foams. Additionally, foams with 10 % phenol substitution by DKL exhibited better thermal stability compared to neat phenolic foams. After 15 days of incubation with Laccase-producing bacterium Bacillus sp., 30 % and 50 % DKL foams exhibited the highest weight loss of 39.03 % and 38.9 %, respectively. Qualitative degree of biodegradation was further assessed using scanning electron microscopy and FT-IR analysis of the degraded samples.

Enhanced Fluorescence Imaging of Implants Based on Polyester Copolymers in Combination With MRI

Nowadays, many biodegradable materials are offered for biomedical applications, but there are only a few in vivo methods for their detection and monitoring. In this work, implants based on biodegradable polyester copolymers were labeled with indocyanine green (ICG) for fluorescence imaging in combination with tissue optical clearing (TOC) and magnetic resonance imaging (MRI). The results include in vitro degradation modeling followed by in vivo imaging of copolymer samples that were subcutaneously implanted in BALB/c mice. TOC with 70% glycerol has been demonstrated to significantly improve sample visualization. The TOC efficiency parameter Q demonstrated the variability of effects correlating with the timing of follow-up in the postimplantation period. It has been shown that nonhealing wounds, peri-implantation inflammation, or fibrosis, confirmed by MRI, affect the effectiveness of TOC in the range from Q = -30% to 70%.

Effect of post-processing on the surface, optical, mechanical, and dimensional properties of 3D-printed orthodontic clear retainers

OBJECTIVES

To address the high surface roughness and poor optical properties of three-dimensional (3D) printed orthodontic clear retainers, an alternative post-processing protocol was investigated with the goal of achieving improved surface, optical, and mechanical properties while preserving dimensional accuracy.

MATERIALS AND METHODS

Samples were prepared from two biocompatible methacrylate-based 3D-printing resins (Formlabs Dental LT Clear V2, NextDent OrthoFlex) and one thermoplastic material (Duran). For the 3D-printed resins, one group was post-processed by rinsing in isopropyl alcohol, while another group was centrifuged before post-curing in glycerine. Three different testing conditions were used: dry, wet (24-h water immersion), and aged (thermocycling for 10,000 cycles). Surface characteristics were evaluated qualitatively and quantitatively. Optical properties were assessed for transparency and colour stability, while mechanical properties were elicited from tensile and microhardness tests. Water sorption and solubility were calculated. Samples mounted on a dental model were scanned by micro-computed tomography to measure thickness and gap width.

RESULTS

3D-printed samples post-processed by centrifugation showed significantly decreased surface roughness and improved visible light transmission, colour stability, tensile strength, and hardness. The centrifuged samples showed significantly increased thickness, while designing an offset equal to this thickness improved the adaptation.

CONCLUSIONS

Post-processing by centrifugation produces surface coating that enhances the surface and optical properties of the 3D-printed orthodontic retainers, while curing in an oxygen-free environment improves their mechanical properties. Design modifications may be necessary for this protocol to ensure proper adaptation to the dentition.

CLINICAL RELEVANCE

Proper design and post-processing protocols are necessary to achieve the desired properties of orthodontic clear retainers.

Poly(3-hydroxybutyrate) Modified with Thermoplastic Polyurethane and Microfibrillated Cellulose: Hydrolytic Degradation and Thermal and Mechanical Properties

Blending poly(3-hydroxybutyrate) (PHB) with other polymers could be a rapid and accessible solution to overcome some of its drawbacks. In this work, PHB was modified with microfibrillated cellulose (MC) and a thermoplastic polyurethane containing biodegradable segments (PU) by two routes, using a masterbatch and by direct mixing. The PU and MC modifiers improved the thermal stability of PHB by up to 13 °C and slightly decreased its melt viscosity and crystallinity, thus improving the melt processability. The addition of PU in PHB composites led to a decrease in the storage modulus, which did not exceed 20% at room temperature. The hydrolytic degradation in an alkaline environment at 50 °C for 28 days decreased the thermal stability of the composites by 58-65 °C, while the lower mass loss and morphological features showed that the PU modifier delayed the degradation of the PHB composites. The improved thermal stability, melt processability, and lower cost, along with higher flexibility and the possibility of controlling the hydrolytic degradation by the PU content, make the PHB/PU/MC composites obtained by the masterbatch method promising materials for medical and engineering applications.

Polymer material biodegradation in the deep sea. A review

The phenomenon of marine plastic pollution is now well-established, with documented impacts on marine biodiversity and biogeochemical cycles. In order to mitigate this environmental impact, a significant amount of research has been conducted in recent years with the objective of developing biodegradable alternatives to conventional polymers and their composites in marine environments. The findings of this research significantly enhanced our understanding of biodegradation mechanisms and identified promising candidates. However, the majority of these studies have been conducted in coastal marine environments, which represent a minor component of the marine ecosystem. Recent models on the transport of plastic debris in the oceans indicate that deep-sea environments are likely to be the ultimate sink for a significant proportion of plastics entering the oceans. The aim of this review is to provide an overview of the processes of biodegradation of polymers in these deep-sea environments. The diversity and specific characteristics of these environments with respect to degradation mechanisms are discussed. While the majority of deep-sea conditions are not conducive to biodegradation, studies on organic falls (wood and whale carcasses) and a few investigations into materials previously shown to be biodegradable in coastal marine environments demonstrate mechanisms that are similar to those observed in shallow waters. Nevertheless, further research is necessary to reach definitive conclusions. It is essential to extend these studies to a broader range of deep-sea environments. Additionally, new methodologies that integrate microbiology and polymer science are required to accurately assess the process of assimilation of these materials in these environments.

Lifetimes and mechanisms of biodegradation of polyhydroxyalkanoate (PHA) in estuarine and marine field environments

Coastal cities face significant challenges from plastic pollution, with most plastics being resistant to biodegradation. Biodegradable plastics are increasingly used to address this issue, particularly for items prone to entering, and then accumulating, in waterways, through littering or leakage. Among biodegradable plastics, polyhydroxyalkanoates (PHAs) are notable as bioderived, bacterially synthesised aliphatic polyesters that are readily biodegradable in varied environments. This study focuses on the lifetimes and biodegradation behaviour of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) sheets submerged in five different aquatic environments (under both surface and benthic conditions) within a single coastal zone over 51 weeks. The biodegradation was characterised through mass and thickness loss, and changes in surface morphology, thermal and mechanical properties, and molecular weight. The findings revealed that the lifetimes of PHBV sheets varied between benthic and surface sites, with all benthic sites exhibiting faster biodegradation rates (0.068 ± 0.019 mg.d-1.cm-2 to 0.163 ± 0.048 mg.d-1.cm-2) compared to the surface (0.032 ± 0.015 mg.d-1.cm-2). Lag times to initiation of biodegradation in the Marina benthic and River benthic sites were similar (9-25 days) with the two other benthic sites (Sea and Mesocosm) comparable with the Marina surface ranging from 41 to 110 days), indicating that the local environment has a stronger influence on lag time as opposed to the specific rate of mass loss following biodegradation onset. UV exposure did not impact the crystallinity of the surface sheets, which remained stable throughout the exposure period. Overall, if thin- walled, (∼150 μm) products made from PHA do leak into the aquatic environment and remain buoyant, then their lifetimes are forecast to be within 1-2 years; if they settle in benthic environments, their lifetimes are likely to be between 4 and 9 months.

A comprehensive review of lignin-reinforced lignocellulosic composites: Enhancing fire resistance and reducing formaldehyde emission

The rising environmental concerns and the growing demand for renewable materials have surged across various industries. In this context, lignin, being a plentiful natural aromatic compound that possesses advantageous functional groups suitable for utilization in biocomposite systems, has gained notable attention as a promising and sustainable alternative to fossil-derived materials. It can be obtained from lignocellulosic biomass through extraction via various techniques, which may cause variability in its thermal, mechanical, and physical properties. Due to its excellent biocompatibility, eco-friendliness, and low toxicity, lignin has been extensively researched for the development of high-value materials including lignin-based biocomposites. Its aromatic properties also allow it to successfully substitute phenol in the production of phenolic resin adhesives, resulting in decreased formaldehyde emission. This review investigated and evaluated the role of lignin as a green filler in lignin-based lignocellulosic composites, aimed at enhancing their fire retardancy and decreasing formaldehyde emission. In addition, relevant composite properties, such as thermal properties, were investigated in this study. Markedly, technical challenges, including compatibility with other matrix polymers that are influenced by limited reactivity, remain. Some impurities in lignin and various sources of lignin also affect the performance of composites. While lignin utilization can address certain environmental issues, its large-scale use is limited by both process costs and market factors. Therefore, the exact mechanism by which lignin enhances flame retardancy, reduces formaldehyde emissions, and improves the long-term durability of lignocellulosic composites under various environmental conditions remains unclear and requires thorough investigation. Life cycle analysis and techno-economic analysis of lignin-based composites may contribute to understanding the overall influence of systems not only at the laboratory scale but also at a larger industrial scale.

(Bio)degradation of biopolymer and biocomposite in deep-sea environments

In order to reduce the contamination of marine ecosystems by plastic materials, the scientific community is engaged in the development of biodegradable substitutes for conventional plastics. While certain candidates have been successfully tested in coastal marine environments, the degradation process in deep-sea environments remains poorly understood. This study examined the degradation of two industrial biopolyesters, a poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and a polybutylene-succinate (PBS), in two deep marine environments of the Middle and Eastern Atlantic, at depths of 780 and 1740 m, as well as under laboratory conditions under hydrostatic pressure and without micro-organisms. The findings reveal a considerable biodeterioration of PHBV and a pronounced influence of flax fibre reinforcement on the degradation mechanisms. Conversely, PBS exhibits minimal to no indications of degradation. Additionally, the results confirm that biotic factors are the primary determinants of the degradation processes, with no degradation observed under abiotic conditions.

Application of Nanoparticles for Immunotherapy of Allergic Rhinitis

Allergen Immunotherapy (AIT) is the only etiological therapeutic method available for allergic rhinitis (AR). Currently, several options for AIT in the market, such as subcutaneous immunotherapy (SCIT) and sublingual immunotherapy (SLIT), have different routes of administration. These traditional methods have achieved encouraging outcomes in clinic. However, the side effects associated with these methods have raised the need for innovative approaches for AIT that improve safety, shorten the course of treatment and increase local drug concentration. Nanoparticles (NPs) are particles ranging in size from 1 to 100 nm, which have been hired as potential adjuvants for AIT. NPs can be employed as agents for modulating immune responses in AR or/and carriers for loading proteins, peptides or DNA molecules. This review focuses on different kinds of nanoparticle delivery systems, including chitosan nanoparticles, exosomes, metal nanoparticles, and viral nanoparticles. We summarized the advantages and limitations of NPs for the treatment of allergic rhinitis. Overall, NPs are expected to be a therapeutic option for AR, which requires more in-depth studies and long-term therapeutic validation.

Erosion of rigid plastics in turbid (sandy) water: quantitative assessment for marine environments and formation of microplastics

Mechanical degradation (erosion) of plastics in the marine environment has been reported in many literature studies but without quantitative information. This type of degradation is crucial as it accounts for most of the initial microplastic products, in marine environments (e.g., rivers and oceans). Here, we quantify the erosion of plastics by water-borne sediments under typical perpendicular water velocities and sand loads of turbid rivers and coastal oceans. Polypropylene (PP) shows the highest response to water-borne erosion, with a surface degradation rate of 5160 μm per year (4.44 mg per mm2 per year), compared with high-density polyethylene (HDPE) with a degradation rate of 1874 μm per year (1.79 mg per mm2 per year), resulting in the formation of microplastics (MPs). The rate of formation of such microplastic particles (>10 μm), as characterised by a laser direct infrared (LDIR) chemical imaging system, amounts to 669 particles per mm2 per year for PP and 187 particles per mm2 per year for HDPE, exhibiting average particle sizes of 60 μm and 23 μm in the same order. Furthermore, surface microscopy provided valuable insights into the dominant erosion mechanisms, revealing three distinct zones and the surface features reveal the brittle erosion behaviours. These results will enable a better assessment of degradation and lifetime prediction of plastics in turbid rivers and coastal oceans, allowing precise estimation of the rate of formation of MPs.

Correlation of Enzymatic Depolymerization Rates with the Structure of Polyethylene-Like Long-Chain Aliphatic Polyesters

Long-chain aliphatic polyesters are emerging sustainable materials that exhibit polyethylene-like properties while being amenable to chemical recycling and biodegradation. However, varying polyester chemical structures results in markedly different degradation rates, which cannot be predicted from commonly correlated bulk polyester properties, such as polymer melting temperature. To elucidate these structure-degradability relationships, long-chain polyesters varying in their monomer composition and crystallinity were subjected to enzymatic hydrolysis, the rates of which were quantified via detection of formed monomers. Copolymers with poorly water-soluble, long-chain diol monomers (e.g., 1,18-octadecanediol) demonstrated strongly reduced depolymerization rates compared to copolymers with shorter chain length diol monomers. This was illustrated by, e.g., the 20× faster hydrolysis of PE-4,18, consisting of 1,4-butanediol and 1,18-octadecanedicarboxylic acid monomers, relative to PE-18,4. The insoluble long-chain diol monomer released upon hydrolysis was proposed to remain attached to the bulk polymer surface, decreasing the accessibility of the remaining ester bonds to enzymes for further hydrolysis. Tuning of polyester crystallinity via the introduction of branched monomers led to variable hydrolysis rates, which increased by an order of magnitude when crystallinity decreased from 72% to 45%. The results reported enables the informed design of polyester structures with balanced material properties and amenability to depolymerization.

Modeling of Dissolving Microneedle-Based Transdermal Drug Delivery: Effects of Dynamics of Polymers in Solution

Dissolving microneedle (DMN)-assisted transdermal drug delivery (TDD) has received attention from the scientific community in recent years due to its ability to control the rate of drug delivery through its design, the choice of polymers, and its composition. The dissolution of the polymer depends strongly on the polymer-solvent interaction and polymer physics. Here, we developed a mathematical model based on the physicochemical parameters of DMNs and polymer physics to determine the drug release profiles. An annular gap width is defined when the MN is inserted in the skin, accumulating interstitial fluid (ISF) from the surrounding skin and acting as a boundary layer between the skin and the MN. Poly(vinylpyrrolidone) (PVP) is used as a model dissolving polymer, and ceftriaxone is used as a representative drug. The model agrees well with the literature data for ex vivo permeation studies, along with the percent height reduction of the MN. Based on the suggested mathematical model, when loading 0.39 mg of ceftriaxone, the prediction indicates that approximately 93% of the drug will be cleared from the bloodstream within 24 h. The proposed modeling strategy can be utilized to optimize drug transport behavior using DMNs.

3D structural analysis of the biodegradability of banana pseudostem nanocellulose bioplastics

X-Ray micro-computed tomography (XCT) is used to reveal the micro-structural changes of banana pseudostem nanocellulose bioplastic due to a biodegradation process initiated in a formulated composting media that allowed the growth of aerobic microflora. The bioplastic itself was made of nanocellulose, which was isolated from banana pseudostem using the 2,2,6,6-Tetramethyl-1-piperidinyloxy (TEMPO) mediated oxidation method, and polyethylene glycol (PEG) as plasticiser. XCT provided insights into the 3D structural change of the bioplastic identifying the degradation process at two scales. The results showed that the local thickness and roughness of the bioplastic increased after degradation, while the density of the material decreased. Enlarged voids and tunnels were observed in the material after degradation. The formation of these tunnels is attributed to the popping of internal PEG-containing voids because of the generation of gases, which after forming may further accelerate biodegradation by microbial activity.

Innovative biomaterials for food packaging: Unlocking the potential of polyhydroxyalkanoate (PHA) biopolymers

Polyhydroxyalkanoate (PHA) biopolyesters show a good balance between sustainability and performance, making them a competitive alternative to conventional plastics for ecofriendly food packaging. With an emphasis on developments over the last decade (2014-2024), this review examines the revolutionary potential of PHAs as a sustainable food packaging material option. It also delves into the current state of commercial development, competitiveness, and the carbon footprint associated with PHA-based products. First, a critical examination of the challenges experienced by PHAs in terms of food packaging requirements is undertaken, followed by an assessment of contemporary strategies addressing permeability, mechanical properties, and processing considerations. The various PHA packaging end-of-life options, including a comprehensive overview of the environmental impact and potential solutions will also be discussed. Finally, conclusions and future perspectives are elucidated with a view of prospecting PHAs as future green materials, with a blend of performance and sustainability of food packaging solutions.

Biodegradation behavior of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) containing phenolic compounds in seawater in laboratory testing conditions

Biodegradation in marine medium of PHBV films with or without 5 % wt. of phenolic compounds (catechin, ferulic acid, and vanillin) was assessed at laboratory scale. Respirometric analyses and film disintegration kinetics were used to monitor the process over a period of 162 days. Structural changes in the films were analyzed throughout the exposure period using FESEM, DSC, Thermogravimetric analyses, XRD, and FTIR spectra. Respirometric tests showed complete biodegradation of all materials during the exposure period (the biodegradation half-time ranged between 63 and 79 days) but at different rates, depending on the phenolic compound incorporated. Ferulic acid and vanillin accelerate the PHBV biodegradation, whereas catechin delayed the process. Disintegration kinetics confirmed these results and showed that degradation occurred from the surface to the interior of the films. This was controlled by the degradation rate of the polymer amorphous phase and the formation of a biomass coating on the film surface. This is the result of the compounds generated by polymer degradation in combination with excretions from microorganisms. This coating has the potential to affect the enzyme diffusion to the polymer substrate. Moreover, the cohesion forces of the amorphous phase (reflected in its glass transition temperature) affected its degradation rate, while the slower degrading crystalline fragments were released, thus contributing to the disintegration process on the film's surface. Ferulic acid, with its hydrolytic effect, enhanced degradation, as did vanillin for its plasticizing and weakening effect in the amorphous phase of polymer matrix. In contrast, catechin with cross-linking effect hindered the progress of the material degradation, considerably slowing down the process rate.

Biodegradable Natural Hydrogels for Tissue Engineering, Controlled Release, and Soil Remediation

This article provides insights into hydrogels of the most promising biodegradable natural polymers and their mechanisms of degradation, highlighting the different possibilities of controlling hydrogel degradation rates. Since biodegradable hydrogels can be designed as scaffolding materials to mimic the physical and biochemical properties of natural tissues, these hydrogels have found widespread application in the field of tissue engineering and controlled release. In the same manner, their potential as water reservoirs, macro- and microelement carriers, or matrixes for the selective adsorption of pollutants make them excellent candidates for sustainable soil amendment solutions. Accordingly, this article summarizes the recent advances in natural biodegradable hydrogels in the fields of tissue engineering, controlled release, and soil remediation, emphasizing the new opportunities that degradability and its tunability offer for the design and applicability of hydrogels.

Evaluation of Mechanical Properties of Composite Material with a Thermoplastic Matrix Reinforced with Cellulose Acetate Microfibers

Low-density polyethylene (LDPE) has been widely used in various applications due to its flexibility, lightness, and low production cost. However, its massive use in disposable products has raised environmental concerns, prompting the search for more sustainable alternatives. This study aims to investigate the mechanical properties achievable in a composite material utilizing low-density polyethylene (LDPE), potato starch (PS), and cellulose microfibrils (MFCA) at loadings of 0.05%, 0.15%, and 0.30%. Initially, the cellulose acetate microfibrils (MFCA) were produced via an electrospinning process. Subsequently, a dispersive mixture of the aforementioned materials was created through the extrusion and pelletizing process to form pellets. These pellets were then molded by injection molding to produce test specimens in accordance with ASTM D 638, the standard for tensile strength testing. The evaluation of the properties was conducted through mechanical tensile tests (ASTM D638), hardness tests (ASTM D 2240), melt flow index (ASTM D1238), and scanning electron microscopy (SEM). This study determined the influence of cellulose acetate microfibril loadings below 0.3% as reinforcement within a thermoplastic LDPE matrix. It was demonstrated that these microfibrils, due to their length-to-diameter ratio, contribute to an enhancement in the mechanical properties.

Stretchable and biodegradable self-healing conductors for multifunctional electronics

As the regenerative mechanisms of biological organisms, self-healing provides useful functions for soft electronics or associated systems. However, there have been few examples of soft electronics where all components have self-healing properties while also ensuring compatibility between components to achieve multifunctional and resilient bio-integrated electronics. Here, we introduce a stretchable, biodegradable, self-healing conductor constructed by combination of two layers: (i) synthetic self-healing elastomer and (ii) self-healing conductive composite with additives. Abundant dynamic disulfide and hydrogen bonds of the elastomer and conductive composite enable rapid and complete recovery of electrical conductivity (~1000 siemens per centimeter) and stretchability (~500%) in response to repetitive damages, and chemical interactions of interpenetrated polymer chains of these components facilitate robust adhesion strength, even under extreme mechanical stress. System-level demonstration of soft, self-healing electronics with diagnostic/therapeutic functions for the urinary bladder validates the possibility for versatile, practical uses in biomedical research areas.

Degradation efficiency of biodegradable plastics in subtropical open-air and marine environments: Implications for plastic pollution

Bioplastics are increasingly used as a solution to tackle plastic pollution problems. However, their degradability in natural environments is currently under debate. To evaluate their degradation efficiencies, we conducted in-situ degradation experiments in an open-air and two marine environments in Hong Kong. Three groups of biodegradable plastic were tested, namely (1) additive-modified low-density polyethylene (LDPE), labelled as oxo-biodegradable or photodegradable plastics, (2) polylactic acid (PLA), and (3) polyvinyl alcohol (PVA)/starch blends. Most biodegradable plastics fail to completely degrade but remain visually present after six months of exposure. Only PLA is able to demonstrate 100 % disintegration in one to three months in marine settings, suggesting that subtropical marine environments may favor PLA degradation. Biodegradable plastics that are bio-based (PLA and PVA/Starch blends) show notably larger mass losses by 23-100 % than the fossil-based ones (modified-LDPE). Our results reveal higher degradation efficiencies of PLA and PVA/Cassava starch blend in marine than open-air settings (with mass losses larger by 50 %, and by 39-41 %, respectively), potentially via biodegradation and hydrolysis. Meanwhile, modified-LDPE and PVA/Corn starch blends in general show higher degradation efficiencies in open-air than marine settings (with mass losses larger by 2 %, and by 17-33 %, respectively), potentially via abiotic oxidation. Since all tested biodegradable plastics exhibit potential fragmentation signs, further investigation is needed to characterize the behaviours of the microplastics generated. The current labelling on biodegradable bags fails to provide comprehensive information regarding their actual environmental degradation behaviours, especially considering their fragmentation risk and limited degradation exhibited in this study. This highlights the imperative for improved messaging to ensure consumers are better informed about these products.

Understanding visible light and microbe-driven degradation mechanisms of polyurethane plastics: Pathways, property changes, and product analysis

The accumulation of polyurethane plastics (PU-PS) in the environment is on the rise, posing potential risks to the health and function of ecosystems. However, little is known about the degradation behavior of PU-PS in the environment, especially water environment. To address this knowledge gap, we investigated and isolated a degrading strain of Streptomyces sp. B2 from the surface of polyurethane coatings. Subsequently, a photoreactor was employed to simulate the degradation process of bio-based polyurethane (BPU) and petroleum-based polyurethane (PPU) under three conditions, including single microorganism (SM), single light exposure (SL), and combined light exposure/microorganism action (ML) in aqueous solution. The results indicated that PU-PS mainly relies on biodegradation, with the highest degradation rate observed after 28 d under SM condition (BPU 5.69 %; PPU 5.25 %). SL inhibited microbial growth and degradation, with the least impact on plastic degradation. Microorganisms colonized the plastic surface, secreting relevant hydrolytic enzymes and organic acids into the culture medium, providing a negative charge. The carbon chains were broken and aged through hydrogen peroxide induction or attack by oxygen free radicals. This process promoted the formation of oxidized functional groups such as OH and CO, disrupting the polymer's structure. Consequently, localized fragmentation and erosion of the microstructure occurred, resulting in the generation of secondary microplastic (MPs) particles, weight loss of the original plastic, increased surface roughness, and enhanced hydrophilicity. Additionally, BPU exhibited greater degradability than PPU, as microorganisms could utilize the produced fatty acids, which promoted their reproduction. In contrast, PPU degradation generated a large amount of isocyanate, potentially toxic to cells and inhibiting biodegradation. This study unveils the significant role of microorganisms in plastic degradation and the underlying degradation mechanisms of BPU, providing a novel strategy for polyurethane degradation and valuable information for comprehensive assessment of the behavior and fate of MPs in the environment.

Synthesis of star-shaped poly(lactide)s, poly(valerolactone)s and poly(caprolactone)s via ROP catalyzed by N-donor tin(ii) cations and comparison of their wetting properties with linear analogues

In this study, we report the use of N-coordinated tin(ii) cations [L1→Sn(H2O)][OTf]2·THF (1) and [L1→SnCl][SnCl3] (2) (L1 = 1,2-(C5H4N-2-CH = N)2CH2CH2) as efficient ROP catalysts, which, in combination with benzyl alcohol, afford well-defined linear poly(ε-caprolactone) (PCL) and poly(δ-valerolactones) (PVL) via an activated monomer mechanism (AMM). Thanks to the versatility of complexes 1 and 2 as catalysts, star-shaped PCL, PVL and PLA were also prepared using three-, four-, five- and six-functional alcohols. The number of arms was determined by SEC-MALS-Visco analysis. Spin-coated thin layers of linear and selected six-armed polymers were further studied in terms of their wettability to water. Attention was focused on the influence of the composition and structure of the polymers. Finally, to increase the hydrophobic properties of the studied polymers, stannaboroxines L2(Ph)Sn[(OB-(C6H4-4-CF3))2O] and L2(Ph)Sn[(OB-(C6H4-3,5-CF3)2)2O] (L2 = C6H3-2,6-(Me2NCH2)2) were applied.

The effect of additives on the biodegradation of polyhydroxyalkanoate (PHA) in marine field trials

The persistence of conventional fossil fuel-derived plastics in marine ecosystems has raised significant environmental concerns. Biodegradable plastics are being explored as an alternative. This study investigates the biodegradation behaviour in two marine environments of melt-extruded sheets of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) bioplastic as well as blends of PHBV with a non-toxic plasticiser (triethyl citrate, TEC) and composites of PHBV with wood flour. Samples were submerged for up to 35 weeks in two subtropical marine conditions: on the sandy seabed in the sublittoral benthic zone and the sandy seabed of an open air mesocosm with pumped seawater. Rates of biodegradation, lag times and times to 95 % mass loss (T95) were determined through mass loss data and Gompertz modelling. Mechanisms of biodegradation were studied through changes in molecular weight, mechanical properties and surface features. Results reveal a rapid biodegradation rate for all PHBV samples, demonstrating a range of specific biodegradation rates relative to exposed surface area of 0.03 ± 0.01 to 0.09 ± 0.04 mg.d-1.cm-2. This rapid rate of biodegradation meant that the subtle variations in biodegradation mechanisms across different sample thicknesses and additive compositions had little effect on overall lifetimes, with the T95 for most samples being around 250-350 days, regardless of site, highlighting the robust biodegradability of PHBV in seawater. It was only the PHBV-wood flour composite that showed faster biodegradation, and that was only in the exposed ocean site. The mesocosm site was otherwise shown to be a good model for the open ocean, with very comparable biodegradation rates and changes in mechanical properties over time.

Synthesis of shape-programmable elastomer for a bioresorbable, wireless nerve stimulator

Materials that have the ability to manipulate shapes in response to stimuli such as heat, light, humidity and magnetism offer a means for versatile, sophisticated functions in soft robotics or biomedical implants, while such a reactive transformation has certain drawbacks including high operating temperatures, inherent rigidity and biological hazard. Herein, we introduce biodegradable, self-adhesive, shape-transformable poly (L-lactide-co-ε-caprolactone) (BSS-PLCL) that can be triggered via thermal stimulation near physiological temperature (∼38 °C). Chemical inspections confirm the fundamental properties of the synthetic materials in diverse aspects, and study on mechanical and biochemical characteristics validates exceptional stretchability up to 800 % and tunable dissolution behaviors under biological conditions. The integration of the functional polymer with a bioresorbable electronic system highlights potential for a wide range of biomedical applications.

Weaponizing chitosan and its derivatives in the battle against lung cancer

Lung cancer (LC) is a crisis of catastrophic proportions. It is a global problem and urgently requires a solution. The classic chemo drugs are lagging behind as they lack selectivity, where their side effects are spilled all over the body, and these adverse effects would be terribly tragic for LC patients. Therefore, they could make a bad situation worse, inflict damage on normal cells, and inflict pain on patients. Since our confidence in classic drugs is eroding, chitosan can offer a major leap forward in LC therapy. It can provide the backbone and the vehicle that enable chemo drugs to penetrate the hard shell of LC. It could be functionalized in a variety of ways to deliver a deadly payload of toxins to kill the bad guys. It is implemented in formulation of polymeric NPs, lipidic NPs, nanocomposites, multiwalled carbon nanotubes, and phototherapeutic agents. This review is a pretty clear proof of chitosan's utility as a weapon in battling LC. Chitosan-based formulations could work effectively to kill LC cells. If a researcher is looking for a vehicle for medication for LC therapy, chitosan can be an appropriate choice.

Utilizing stem cell-secreted molecules as a versatile toolbox for skin regenerative medicine

Stem cells are recognized as an important target and tool in regenerative engineering. In this study, we explored the feasibility of engineering amniotic fluid-derived mesenchymal stem cell-secreted molecules (afMSC-SMs) as a versatile bioactive material for skin regenerative medicine applications in a time- and cost-efficient and straightforward manner. afMSC-SMs, obtained in powder form through ethanol precipitation, effectively contributed to preserving the self-renewal capacity and differentiation potential of primary human keratinocytes (pKCs) in a xeno-free environment, offering a potential alternative to traditional culture methods for their long-term in vitro expansion, and allowed them to reconstitute a fully stratified epithelium sheet on human dermal fibroblasts. Furthermore, we demonstrated the flexibility of afMSC-SMs in wound healing and hair regrowth through injectable hydrogel and nanogel-mediated transdermal delivery systems, respectively, expanding the pool of regenerative applications. This cell-free approach may offer several potential advantages, including streamlined manufacturing processes, scalability, controlled formulation, longer shelf lives, and mitigation of risks associated with living cell transplantation. Accordingly, afMSC-SMs could serve as a promising therapeutic toolbox for advancing cell-free regenerative medicine, simplifying their broad applicability in various clinical settings.

Degradation profiles of the poly(ε-caprolactone)/silk fibroin electrospinning membranes and their potential applications in tissue engineering

Degradation profiles are critical for the optimal application of electrospun polymer nanofibers in tissue regeneration, wound healing, and drug delivery systems. In this study, natural and synthetic polymers and their composites were subjected to in vivo transplantation and in vitro treatment with lipases, macrophages, and acetic acid to evaluate their degradation patterns. The effects of environmental stimulation, surface wettability, and polymer components on the degradation profiles of the electrospinning poly(ε-caprolactone)/silk fibroin (PCL/SF) nanofibers were first evaluated. In vivo degradation study demonstrated that bulk degradation, characterized by the transition from microfibers to nanofibers, and surface erosion, characterized by fusion between the microfibers or direct erosion from both ends of the microfibers, occurred in the electrospun membranes; however, bulk degradation dominated their overall degradation. Furthermore, the degradation rates of the electrospun PCL/SF membranes varied according to the composition, morphology, and surface wettability of the composite membranes. After the incorporation of silk fibroin (SF), the degradation rate of the SF/PCL composite membranes was faster, accompanied by larger values of weight loss and molecular weight (Mw) loss when compared with that of the pure poly(ε-caprolactone) (PCL) membrane, indicating a close relationship between degradation rate and hydrophilicity of the electrospinning membranes. The in vitro experimental results demonstrated that enzymes and oxidation partially resulted in the surface erosion of the PCL/SF microfibers. Consequently, bulk degradation and surface erosion coordinated with each other to enhance the hydrophilicity of the electrospinning membranes and accelerate the in vivo degradation.

Chemically Recyclable and Biodegradable Vulcanized Rubber

The cross-linked nature of vulcanized rubbers as used in tire and many other applications prohibits an effective closed-loop mechanical or chemical recycling. Moreover, vulcanization significantly retards the material's biodegradation. Here, we report a recyclable and biodegradable rubber that is generated by the vulcanization of amorphous, unsaturated polyesters. The elastic material can be broken down via solvolysis into the underlying monomers. After removal of the vulcanized repeat units, the saturated monomers, constituting the major share of the material, can be recovered in overall recycling rates exceeding 90%. Respirometric biodegradation experiments by 13CO2 tracking under environmental conditions via the polyesters' diol monomer indicated depolymerization and partial mineralization of the vulcanized polyester rubbers.

Effects of poly(3-hydroxybutyrate) [P(3HB)] coating on the bacterial communities of artificial structures

The expanding urbanization of coastal areas has led to increased ocean sprawl, which has had both physical and chemical adverse effects on marine and coastal ecosystems. To maintain the health and functionality of these ecosystems, it is imperative to develop effective solutions. One such solution involves the use of biodegradable polymers as bioactive coatings to enhance the bioreceptivity of marine and coastal infrastructures. Our study aimed to explore two main objectives: (1) investigate PHA-degrading bacteria on polymer-coated surfaces and in surrounding seawater, and (2) comparing biofilm colonization between surfaces with and without the polymer coating. We applied poly(3-hydroxybutyrate) [P(3HB)) coatings on concrete surfaces at concentrations of 1% and 6% w/v, with varying numbers of coating cycles (1, 3, and 6). Our findings revealed that the addition of P(3HB) indeed promoted accelerated biofilm growth on the coated surfaces, resulting in an occupied area approximately 50% to 100% larger than that observed in the negative control. This indicates a remarkable enhancement, with the biofilm expanding at a rate roughly 1.5 to 2 times faster than the untreated surfaces. We observed noteworthy distinctions in biofilm growth patterns based on varying concentration and number of coating cycles. Interestingly, treatments with low concentration and high coating cycles exhibited comparable biofilm enhancements to those with high concentrations and low coating cycles. Further investigation into the bacterial communities responsible for the degradation of P(3HB) coatings identified mostly common and widespread strains but found no relation between the concentration and coating cycles. Nevertheless, this microbial degradation process was found to be highly efficient, manifesting noticeable effects within a single month. While these initial findings are promising, it's essential to conduct tests under natural conditions to validate the applicability of this approach. Nonetheless, our study represents a novel and bio-based ecological engineering strategy for enhancing the bioreceptivity of marine and coastal structures.

A Review of Weathering Studies in Plastics and Biocomposites-Effects on Mechanical Properties and Emissions of Volatile Organic Compounds (VOCs)

Polymeric materials undergo degradation when exposed to outdoor conditions due to the synergistic effects of sunlight, air, heat, and moisture. The degradation can lead to a decline in mechanical properties, fading, surface cracking, and haziness, attributed to the cleavage of the polymer chains and oxidation reactions. Accelerated weathering testing is a useful technique to evaluate the comparative photodegradation of materials within a reasonable timeframe. This review gives an overview of the different degradation mechanisms occurring in conventional plastics and bio-based materials. Case studies on accelerated weathering and its effect on the mechanical properties of conventional plastics and biocomposites are discussed. Different techniques for analysing volatile organic emissions (VOCs) have been summarized and studies highlighting the characterization of VOCs from aged plastics and biocomposites after aging have been cited.

Evaluation and Modeling of Polylactide Photodegradation under Ultraviolet Irradiation: Bio-Based Polyester Photolysis Mechanism

In our study, we investigated the accelerated aging process of PLA under 253.7 nm UV-C irradiation with the use of the GPC, NMR, FTIR, and DSC methods and formal kinetic analysis. The results of GPC and DSC indicated a significant degree of destructive changes in the PLA macromolecules, while spectroscopic methods NMR and FTIR showed maintenance of the PLA main structural elements even after a long time of UV exposure. In addition to that, the GPC method displayed the formation of a high molecular weight fraction starting from 24 h of irradiation, and an increase in its content after 144 h of irradiation. It has been shown for the first time that a distinctive feature of prolonged UV exposure is the occurrence of intra- and intermolecular radical recombination reactions, leading to the formation of a high molecular weight fraction of PLA decomposition products. This causes the observed slowdown of the photolysis process. It was concluded that photolysis of PLA is a complex physicochemical process, the mechanism of which depends on morphological changes in the solid phase of the polymer under UV radiation.

Biosafety consideration of nanocellulose in biomedical applications: A review

Nanocellulose-based biomaterials have gained significant attention in various fields, especially in medical and pharmaceutical areas, due to their unique properties, including non-toxicity, high specific surface area, biodegradability, biocompatibility, and abundant feasible and sophisticated strategies for functional modification. The biosafety of nanocellulose itself is a prerequisite to ensure the safe and effective application of biomaterials as they interact with living cells, tissues, and organs at the nanoscale. Potential residual endogenous impurities and exogenous contaminants could lead to the failure of the intended functionalities or even serious health complications if they are not adequately removed and assessed before use. This review summarizes the sources of impurities in nanocellulose that may pose potential hazards to their biosafety, including endogenous impurities that co-exist in the cellulosic raw materials themselves and exogenous contaminants caused by external exposure. Strategies to reduce or completely remove these impurities are outlined and classified as chemical, physical, biological, and combined methods. Additionally, key points that require careful consideration in the interpretation of the biosafety evaluation outcomes were discussed to ensure the safety and effectiveness of the nanocellulose-based biomaterials in medical applications.

Deterioration of single-use biodegradable plastics in high-humidity air and freshwaters over one year: Significant disparities in surface physicochemical characteristics and degradation rates

More single-use plastics are accumulating in the environment, and likewise biodegradable plastics (BPs), which are being vigorously promoted, cannot escape the fate. Currently, studies on the actual degradation of BPs in open-air and freshwaters are underrepresented despite they are potentially headmost leakage and contamination sites for disposable BPs. Herein, we compared the degradation behavior of six BP materials and non-degradable polypropylene (PP) plastics over a 1-year in situ suspension in the high-humidity air, a eutrophic river, and an oligotrophic lake. Moreover, a 3-months laboratory incubation was performed to detect the release of dissolved organic carbon (DOC) from BPs. In both air and freshwaters, poly(p-dioxanone) (PPDO) degraded significantly while PP and polylactic acid (PLA) showed no signs of degradation. The average degradation rates of three poly(butylene adipate-co-terephthalate) (PBAT)-based films varied: 100% in river, 55% in lake, and 10% in air. In addition to PLA, surface chemical groups, hydrophilicity, and thermal stability of BPs changed, and microplastics were found on their surfaces. Correspondingly, BPs with faster degradation rates released relatively higher amounts of DOC. Environmental microbial and chemical characteristics may contribute to differences in BP degradation besides polymer specificity. Altogether, our results indicate the need for appropriate monitoring of BPs.

A review on fate and ecotoxicity of biodegradable microplastics in aquatic system: Are biodegradable plastics truly safe for the environment?

Plastic products are extensively used worldwide, but inadequate management of plastic waste results in significant plastic pollution. Biodegradable plastic (BPs) offers an alternative to traditional plastics, however, not all BPs can fully degrade under natural conditions. Instead, they may deteriorate into biodegradable microplastic (BMPs) at a faster rate than conventional plastic, thereby posing an additional hazard to aquatic environments. This study provides a comprehensive overview of the fate of BPs in aquatic systems and their eco-toxicological effects on aquatic organisms such as algae, invertebrates, and fish. The findings highlight that BMPs have comparable or heightened effects compared to conventional microplastics (MPs) which physiochemical characteristic of the polymer itself or by the chemical leached from the polymeric matrix can affect aquatic organisms. While BPs is not a flawless solution to address plastic pollution, future research should prioritize investigating their production, environmental behavior, ecological impact, and whether BMPs inflict greater harm than conventional MPs.

Degradation behaviour of porous poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) scaffolds in cell culture

Exploring the degradation behaviour of biomaterials in a complex in vitro physiological environment can assist in predicting their performance in vivo, yet this aspect remains largely unexplored. In this study, the in vitro degradation over 12 weeks of porous poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) bone scaffolds in human osteoblast (hOB) culture was investigated. The objective was to evaluate how the presence of cells influenced both the degradation behaviour and mechanical stability of these scaffolds. The molecular weight (Mw) of the scaffolds decreased with increasing incubation time and the Mw reduction rate (6.2 ± 0.4 kg mol-1 week-1) was similar to that observed when incubated in phosphate buffered saline (PBS) solution, implying that the scaffolds underwent hydrolytic degradation in hOB culture. The mass of the scaffolds increased by 0.8 ± 0.2 % in the first 4 weeks, attributed to cells attachment and extracellular matrix (ECM) deposition including biomineralisation. During the first 8 weeks, the nominal compressive modulus, E⁎, of the scaffolds remained constant. However, it increased significantly from Week 8 to 12, with increments of 55 % and 42 % in normal and lateral directions, respectively, attributed to the reinforcement effect of cells, ECM and minerals attached on the surface of the scaffold. This study has highlighted, that while the use of PBS in degradation studies is suitable for evaluating Mw changes it cannot predict changes in mechanical properties to PHBV scaffolds in the presence of cells and culture media. Furthermore, the PHBV scaffolds had mechanical stability in cell culture for 12 weeks validating their suitability for tissue engineering applications.

Characterization of the degradation products of biodegradable and traditional plastics on UV irradiation and mechanical abrasion

Biodegradable plastics are popular alternatives to traditional plastics in packaging, mulch sheets, and other applications. However, there are concerns regarding the potential for pollution as a result of their abiotic degradation. In this study, we investigated the degradation of biodegradable polybutylene adipate terephthalate/polylactic acid (PBAT/PLA) and traditional polyethylene (PE) plastic under two typical abiotic conditions: ultraviolet (UV) irradiation and mechanical abrasion (MA) for up to nine months. The physical and chemical properties of the two plastics during the degradation period were assessed. In addition, quantitative analysis of the degradation products was carried out using a new method called membrane filtration and total organic carbon determination (MF-TOCD). The results revealed that PBAT/PLA underwent a greater number of changes in surface morphology, thermal stability, and mass loss compared to PE when exposed to UV and MA during the test period. Further analysis of the released products revealed that PBAT/PLA released more products than PE. Overall, PE mainly produced microplastics (MPs) larger than 0.22 μm, whereas PBAT/PLA produced products <0.22 μm (nanoplastics and soluble molecules) on UV exposure. In contrast, when subjected to MA, PBAT/PLA produced MPs larger than 0.22 μm, and these accumulated gradually; this behavior is similar to that of PE. By combining the mass loss and the TOC data for the degradation products, we determined that long-term UV irradiation generated a large number of smaller particles from PBAT/PLA that could further degrade rather than accumulate in the environment. In summary, we established a new method to separate and characterize MPs as well as nanoplastics and soluble molecules, and provided new insights into the fate of PBAT/PLA during abiotic degradation.

Rapid marine degradable poly(butylene oxalate) by introducing promotion building blocks

The design and development of high-performance marine-degradable plastics have long been considered a superior strategy to address marine plastic pollution. To achieve a balance between rapid marine degradability and high performance of polyester plastics, this work designed two series of poly(butylene oxalate) (PBOx) copolymers with intrinsic hydrolysis ability using poly(ethylene oxalate) (PEOx) and poly(glycolic acid) (PGA) as promotion building blocks. The synthesis process, crystallization properties, barrier performance, and mechanical properties of copolymers were comparatively investigated. Additionally, the marine degradability of copolymers received specific focus. The theoretical calculation demonstrated that the introduction of promotion blocks reduced the hydrolysis energy barrier of the copolymers. In general, the results revealed the advantages of PBEOx copolymer in satisfying practicality and better regulating marine degradability. The high gas barrier performance, suitable thermal properties, tunable mechanical properties, and rapid marine degradability endow the copolymer as a promising candidate toward sustainable and marine-degradable plastics.

Hybrid interpenetrating network of polyester coronary stent with tunable biodegradation and mechanical properties

Poly(l-lactide) (PLLA) is an important candidate raw material of the next-generation biodegradable stent for percutaneous coronary intervention, yet how to make a polyester stent with sufficient mechanical strength and relatively fast biodegradation gets to be a dilemma. Herein, we put forward a hybrid interpenetrating network (H-IPN) strategy to resolve this dilemma. As such, we synthesize a multi-functional biodegradable macromer of star-like poly(d,l-lactide-co-ɛ-caprolactone) with six acrylate end groups, and photoinitiate it, after mixing with linear PLLA homopolymer, to trigger the free radical polymerization. The resultant crosslinked polymer blend is different from the classic semi-interpenetrating network, and partial chemical crosslinking occurs between the linear polymer and the macromer network. Combined with the tube blow molding and the postprocessing laser cutting, we fabricate a semi-crosslinked-polyester biodegradable coronary stent composed of H-IPN, which includes a physical network of polyester spherulites and a chemical crosslinking network of copolyester macromers and a part of homopolymers. Compared with the currently main-stream PLLA stent in research, this H-IPN stent realizes a higher and more appropriate biodegradation rate while maintaining sufficient radial strength. A series of polymer chemistry, polymer physics, polymer processing, and in vitro and in vivo biological assessments of medical devices have been made to examine the H-IPN material. The interventional implanting of the H-IPN stent into aorta abdominalis of rabbits and the follow-ups to 12 months have confirmed the safety and effectiveness.

Development of Eco-Friendly Biocomposite Films Based on Opuntia ficus-indica Cladodes Powder Blended with Gum Arabic and Xanthan Envisaging Food Packaging Applications

Currently, food packaging is facing a critical transition period and a major challenge: it must preserve the food products' quality and, at the same time, it must meet the current requirements of the circular economy and the fundamental principles of packaging materials eco-design. Our research presents the development of eco-friendly packaging films based on Opuntia ficus-indica cladodes (OFIC) as renewable resources. OFIC powder (OFICP)-agar, OFICP-agar-gum arabic (GA), and OFICP-agar-xanthan (XG) blend films were eco-friendlily prepared by a solution casting method. The films' properties were investigated by scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (X-RD), and differential scanning calorimeter (DSC). Water solubility and moisture content were also determined. Morphology, thickness, molecular interactions, miscibility, crystallinity, and thermal properties, were affected by adjusting the gums (GA and XG) content and glycerol in the blend films. Moisture content increased with increasing glycerol and XG content, and when 1.5 g of GA was added. Water solubility decreased when glycerol was added at 50% and increased with increasing GA and XG content. FTIR and XRD confirmed strong intermolecular interactions between the different blend film compounds, which were reflected in the shifting, appearance, and disappearance of FTIR bands and XRD peaks, indicating excellent miscibility. DSC results revealed a glass transition temperature (Tg) below room temperature for all prepared blend films, indicating that they are flexible and soft at room temperature. The results corroborated that the addition of glycerol at 30% and the GA to the OFICP increased the stability of the film, making it ideal for different food packaging applications.

Protein modified cellulose nanocrystals on reinforcement and self-driven biodegradation of aliphatic polyester

Due to the highly environment-dependent biodegradation and uncontrolled degradation period, the long-run feasibility and effectiveness of biodegradable polymers are extensively questioned to solve plastics waste accumulation and pollution problems. This work physically incorporated lipase PS from Burkholderia cepacian on cellulose nanocrystals (CNC) and embedded it in polycaprolactone (PCL) to construct stable and controllable interfacial microenvironment between CNC and PCL for the reinforcement and controllable self-driven biodegradation. The physical adsorption of lipase PS on CNC was studied by monitoring the surface charge and particle size. FT-IR spectra confirmed the successful incorporation of lipase PS and CNC. Compared with CNC, protein-modified CNC had a higher maximum thermal decomposition temperature of 345 °C and lower interfacial tension of 11 mN/m with PCL which provided PCL composites with higher nucleation efficiency and tensile elongation of 1086 % at break. In addition, only 0.67 % embedded lipase PS completely hydrolyzed PCL membranes in <140 h. The post-compression molding at 80-100 °C had negligible influence on the lipase activity, which indicated that CNC could protect the lipase from inactivation in polymer extrusion and compression. This work also highlighted protein-modified CNC as a new technology for polymer reinforcement.

Degradation and lifetime prediction of plastics in subsea and offshore infrastructures

Engineering and civil developments have relied on synthetic polymers and plastics (including polyethylene, polypropylene, polyamide, etc.) for decades, especially where their durability protects engineering structures against corrosion and other environmental stimuli. Offshore oil and gas infrastructure and renewable energy platforms are typical examples, where these plastics (100,000 s of metric tonnes worldwide) are used primarily as functional material to protect metallic flowlines and subsea equipment against seawater corrosion. Despite this, the current literature on polymers is limited to sea-surface environments, and a model for subsea degradation of plastics is needed. In this review, we collate relevant studies on the degradation of plastics and synthetic polymers in marine environments to gain insight into the fate of these materials when left in subsea conditions. We present a new mathematical model that accounts for various physicochemical changes in the oceanic environment as a function of depth to predict the lifespan of synthetic plastics and the possible formation of plastic debris, e.g., microplastics. We found that the degradation rate of the plastics decreases significantly as a function of water depth and can be estimated quantitatively by the mathematical model that accounts for the effect (and sensitivity) of geographical location, temperature, light intensity, hydrostatic pressure, and marine sediments. For instance, it takes a subsea polyethylene coating about 800 years to degrade on ocean floor (as opposed to <400 years in shallow coastal waters), generating 1000s of particles per g of degradation under certain conditions. Our results demonstrate how suspended sediments in the water column are likely to compensate for the decreasing depth-corrected degradation rates, resulting in surface abrasion and the formation of plastic debris such as microplastics. This review, and the complementing data, will be significant for the environmental impact assessment of plastics in subsea infrastructures. Moreover, as these infrastructures reach the end of their service life, the management of the plastic components becomes of great interest to environmental regulators, industry, and the community, considering the known sizeable impacts of plastics on global biogeochemical cycles.

Polylactic Acid Microplastics Do Not Exhibit Lower Biological Toxicity in Growing Mice Compared to Polyvinyl Chloride Microplastics

Biomicroplastics (BMPs) will be produced during bioplastic degradation (i.e., polylactic acid), although bioplastics have been widely used for food packaging. Like conventional microplastics (MPs), BMPs would be mistakenly ingested into the body through diet or drinking water, but their health risks in vivo are poorly understood. Here, we deeply compared the toxicity difference between irregularly shaped polylactic acid (PLA-MPs, 16-350 μm) and polyvinyl chloride (PVC-MPs, 40-300 μm) MPs in growing mice. After six weeks of exposure, PLA-MP exposure resulted in more severe inhibition of the mice's weight gain than PVC-MPs did. Both PLA- and PVC-MPs significantly elevated the levels of oxidative stress. Moreover, significant changes including altered transcriptional profiles and significantly differentially expressed genes in liver and colon transcription levels were observed in the PVC- and PLA-MP groups. Compared with PVC-MPs, PLA-MPs have a stronger effect on lipid metabolism and digestive systems. PLA-MPs also caused gut microbiota dysbiosis, significantly interfering with the relative abundance of microbiota and altering microbial diversity. These findings indicated the toxicities of PLA-MPs in growing mice were not significantly reduced compared to PVC-MPs, which would also provide new insights for re-examining bioplastic safety.

High-Molecular-Weight and Light-Colored Disulfide-Bond-Embedded Polyesters: Accelerated Hydrolysis Triggered by Redox Responsiveness

Disulfide bonds have attracted considerable attention due to their reduction responsiveness, but it is crucial and challenging to prepare disulfide-bond-based polyesters by melt polycondensation. Herein, the inherently poor thermal stability of the S-S bond in melting polycondensation was overcome. Moreover, poly(butylene succinate-co-dithiodipropionate) (PBSDi) with a light color and high molecular weights (Mn values up to 84.7 kg/mol) was obtained. These polyesters can be applied via melt processing with Td,5% > 318 °C. PBSDi10-PBSDi40 shows good crystallizability (crystallinity 56-38%) and compact lamellar thickness (2.9-3.2 nm). Compared with commercial poly(butylene adipate-co-terephthalate) (PBAT), the elevated mechanical and barrier performances of PBSDi make them better packaging materials. For the degradation behavior, the disulfide monomer obviously accelerates the enzyme degradation but has a weaker effect on hydrolysis. In 0.1 mol/L or higher concentrations of H2O2 solutions, the oxidation of disulfide bonds to sulfoxide and sulfone groups can be realized. This process results in a stronger nucleophilic attack, as confirmed by the Fukui function and DFT calculations. Additionally, the greater polarity and hydrophilicity of oxidation products, proved by noncovalent interaction analysis, accelerate the hydrolysis of polyesters. Moreover, glutathione-responsive breakage, from polymers to oligomers, is confirmed by an accelerated decline in molecular weight. Our research offers fresh perspectives on the effective synthesis of the disulfide polyester and lays a solid basis for the creation of high-performance biodegradable polyesters that degrade on demand.