Assessment of biochar and zero-valent iron for in-situ remediation of chromated copper arsenate contaminated soil

Immobilisation of arsenic and simultaneous degradation of polycyclic aromatic hydrocarbons in soil in situ by modified electrooxidation

Improper management of wood impregnation chemicals and treated wood has led to soil contamination at many wood treatment sites, particularly with toxic substances like creosote oil and chromated copper arsenate (CCA). The simultaneous presence of these pollutants complicates the choice of soil remediation technologies, especially if they are to be applied in situ. In this laboratory study, we attempted to immobilise arsenic (As) and simultaneously degrade polycyclic aromatic hydrocarbons (PAHs) (constituents of creosote oil) by applying a modified electrochemical oxidation method. The supply of iron (Fe) amendments in contaminated soil was done using corroding Fe electrodes as an Fe source and applying an alternating polarity electrical current. Soil with a large fraction of organic matter (25%) and containing 505 mg kg-1 As and 5160 mg kg-1 16-PAHs was placed in Plexiglas cells equipped with porewater samplers and an iron electrode pair connected to a power supply unit. The porewater and percolating solution were periodically sampled and analysed over an 8-week period. The modified electrochemical soil treatment led to a decrease in the total concentration of 16-PAHs in soil by 56-68%. The amount of poorly crystalline Fe oxides in the soil substantially increased, especially close to the electrodes, enabling 76-89% of As to be bound to this most reactive Fe fraction. Nevertheless, over 10% of soil As remained in the most soluble and available fraction (exchangeable), most likely due to the decline in soil redox potential over time. This study suggests that electrochemical oxidation of organic soil with mixed contaminants could be used for in situ soil remediation but needs further improvement to achieve more efficient As immobilisation.

A critical review of nitrate reduction by nano zero-valent iron-based composites for enhancing N2 selectivity

Due to the highly reductive capacity of nano zero-valent iron (nZVI) nanoparticles, the reduction of nitrate (NO3--N) is prone to produce ammonia nitrogen (NH4+-N) as a by-product and has low selectivity for nitrogen gas (N2). Water and dissolved oxygen (DO) in the solution consume electrons from nZVI, decreasing the efficiency of NO3--N reduction. In order to overcome the drawbacks of plain nZVI being used to remove NO3--N pollution, nZVI-based multifunctional materials have been constructed to realize the selective conversion of NO3--N to N2 as well as the efficient removal of NO3--N. Therefore, advanced research on the reduction of NO3--N by nZVI-based composites has been comprehensively reviewed. Strategies to improve NO3--N reduction efficiency and N2 selectivity are proposed. Moreover, the shortcomings of iron-based nanomaterials in NO3--N pollution control have been summarized, and some suggestions for future research directions provided.

Application of soil amendments to reduce the transfer of trace metal elements from contaminated soils of Lubumbashi (Democratic Republic of the Congo) to vegetables

The extraction of copper and cobalt from mines has led to the contamination of agricultural soils by trace metal elements (TMEs) (e.g. Cu: 204 to 1355 mg/kg). The mining industry is one of the sources of metal discharges into the environment, contributing to water, soil, and air contamination and causing metabolic disorders in the inhabitants of the city of Lubumbashi (R.D. Congo). This study assessed the effectiveness of organocalcareous soil improvers applied to TME-contaminated soils to reduce their transfer to plants. Following a factorial design, increasing doses of organic soil improvers (chicken droppings and sawdust) and agricultural lime were applied to the soils of three market gardens (high, medium, and low Cu contamination). The experiment was monitored for 60 days. Soil physicochemical properties (pH, TOC, and total and available copper, cobalt, lead, cadmium, and zinc (mg/kg)) were determined for the three gardens and in the vegetable biomass. The daily consumption index of the vegetables was determined based on total TME content. The results show that organocalcareous soil improvers did not promote plant growth and survival on soils with high and medium levels of copper contamination. However, on soils with low copper content, organocalcareous soil improvers improved germination and plant survival and reduced the transfer of metals from the soil to the plants. The best germination and plant survival rates were obtained with the lightly contaminated market garden. In addition, the organo-limestone amendments applied to the soils slightly increased the soil pH from acidic to slightly acidic, with pH values ranging from (5.43 ± 0.07 to 7.26 ± 0.33). The daily vegetable consumption index obtained for cobalt in the low-contaminated garden ranged from (0.029 to 0.465 mg/60 kg/day), i.e. from 0.5 to 8.45 times higher than the FAO/WHO limit, unlike the other trace metals (Cd, Cu and Pb) for which the daily consumption index found was lower than the FAO/WHO limit. Organocalcareous soil improvers can only be applied to soils with low levels of TME contamination, but for soils with medium to high levels of metal contamination, new soilless production techniques such as hydroponics or bioponics are needed.

Cobalt/Iron Bimetallic Biochar Composites for Lead(II) Adsorption: Mechanism and Remediation Performance

The performance of nano-zero-valent iron for heavy metal remediation can be enhanced via incorporation into bimetallic carbon composites. However, few economical and green approaches are available for preparing bimetallic composite materials. In this study, novel Co/Fe bimetallic biochar composites (BC@Co/Fe-X, where X = 5 or 10 represents the CoCl2 concentration of 0.05 or 0.1 mol L-1) were prepared for the adsorption of Pb2+. The effect of the concentration of cross-linked metal ions on Pb2+ adsorption was investigated, with the composite prepared using 0.05 mol L-1 Co2+ (BC@Co/Fe-5) exhibiting the highest adsorption performance. Various factors, including the adsorption period, Pb2+ concentration, and pH, affected the adsorption of Pb2+ by BC@Co/Fe-5. Further characterisation of BC@Co/Fe-5 before and after Pb2+ adsorption using methods such as X-ray diffraction and X-ray photoelectron spectroscopy suggested that the Pb2+ adsorption mechanism involved (i) Pb2+ reduction to Pb0 by Co/Fe, (ii) Co/Fe corrosion to generate Fe2+ and fix Pb2+ in the form of PbO, and (iii) Pb2+ adsorption by Co/Fe biochar. Notably, BC@Co/Fe-5 exhibited excellent remediation performance in simulated Pb2+-contaminated water and soil with good recyclability.

Phosphorus-Loaded Biochar-Assisted Phytoremediation to Immobilize Cadmium, Chromium, and Lead in Soils

Soil contamination with heavy metals (HM) poses significant challenges to food security and public health, requiring the exploration of effective remediation strategies. This study aims to evaluate the remediation process of soils contaminated with Cd, Cr, and Pb using Lolium perenne assisted by four types of biochar: (i) activated coffee husk biochar (BAC), (ii) nonactivated biochar coffee husk (BSAC), (iii) activated sugar cane leaf biochar (BAA), and (iv) nonactivated biochar sugar cane leaf (BSAA). Biochar, loaded with phosphorus (P), was applied to soils contaminated with Cd, Cr, and Pb. L. perenne seedlings, averaging 2 cm in height, were planted. The bioavailability of P and heavy metals (HM) was monitored every 15 days until day 45, when the seedlings reached an average height of 25 cm. At day 45, plant harvesting was conducted and stems and roots were separated to determine metal concentrations in both plant parts and the soil. The study shows that the combined application of biochar and L. perenne positively influences the physicochemical properties of the soil, resulting in an elevation of pH and electrical conductivity (EC). The utilization of biochar contributes to an 11.6% enhancement in the retention of HM in plant organs. The achieved bioavailability of heavy metals in the soil was maintained at levels of less than 1 mg/kg. Notably, Pb exhibited a higher metal retention in plants, whereas Cd concentrations were comparatively lower. These findings indicate an increase in metal immobilization efficiencies when phytoremediation is assisted with P-loaded biochar. This comprehensive assessment highlights the potential of biochar-assisted phytoremediation as a promising approach for mitigating heavy metal contamination in soils.

Effects of biochar and zero valent iron on the bioavailability and potential toxicity of heavy metals in contaminated soil at the field scale

Heavy metals (HMs) such as copper, nickel and chromium are toxic, so soil contaminated with these metals is of great concern. In situ HM immobilization by adding amendments can decrease the risk of contaminants being released. A five-month field-scale study was performed to assess how different doses of biochar and zero valent iron (ZVI) affect HM bioavailability, mobility, and toxicity in contaminated soil. The bioavailabilities of HMs were determined and ecotoxicological assays were performed. Adding 5 % biochar, 10 % ZVI, 2 % biochar + 1 % ZVI, and 5 % biochar + 10 % ZVI to soil decreased Cu, Ni and Cr bioavailability. Metals were most effectively immobilized by adding 5 % biochar + 10 % ZVI, and the extractable Cu, Ni, and Cr contents were 60.9 %, 66.1 % and 38.9 % lower, respectively, for soil with 5 % biochar + 10 % ZVI added than unamended soil. The extractable Cu, Ni, and Cr contents were 64.2 %, 59.7 % and 16.7 % lower, respectively, for soil with 2 % biochar + 1 % ZVI added than unamended soil. Experiments using wheat, pak choi and beet seedlings were performed to assess the remediated soil toxicity. Growth was markedly inhibited in seedlings grown in extracts of soil with 5 % biochar, 10 % ZVI, or 5 % biochar + 10 % ZVI added. More growth occurred in wheat and beet seedlings after 2 % biochar + 1 % ZVI treatment than the control, possibly because 2 % biochar + 1 % ZVI simultaneously decreased the extractable HM content and increased the soluble nutrient (carbon and Fe) content of the soil. A comprehensive risk assessment indicated that adding 2 % biochar + 1 % ZVI gave optimal remediation at the field scale. Using ecotoxicological methods and determining the bioavailabilities of HMs can allow remediation methods to be identified to efficiently and cost-effectively decrease the risks posed by multiple metals in soil at contaminated sites.

Impacts of biochar materials on copper speciation, bioavailability, and toxicity in chromated copper arsenate polluted soil

Trace element polluted soils pose risks to human and environmental health. Biochar can decrease trace element bioavailability in soils, but their resulting ability to reduce soil toxicity may vary significantly depending on feedstocks used, pyrolysis conditions, and the target pollutants. Chromated copper arsenate (CCA) polluted sites are common, but only very few types of biochar have been tested for these sites. Hence, we tested fourteen well-characterized biochar materials for their ability to bind Cu and reduce toxicity in a CCA polluted soil in a 56-day experiment. Biochar (1%, wt/wt) increased plant (wheat, Triticum aestivum L.) shoot and root growth by 6-58% and 0-73%, reduced soil toxicity to Arthrobacter globiformis by 7-55%, decreased bioavailable Cu (Pseudomonas fluorescens bioreporter) by 5-65%, and decreased free Cu2+ ion activities by 27-89%. The A. globiformis solid-contact test constituted a sensitive ecotoxicological endpoint and deserves further attention for assessment of soil quality. Oil seed rape straw biochar generally performed better than other tested biochar materials. Biochar performance was positively correlated with its high cation exchange capacity, multiple surface functional groups, and high nitrogen and phosphorus content. Our results pave the way for future selection of feedstocks for creation of modified biochar materials with optimal performance in CCA polluted soil.

Genetic circuits in microbial biosensors for heavy metal detection in soil and water

With the rapid population growth, the world is witnessing an ever-increasing demand for energy and natural resources. Consequently, soil, air, and water are polluted with diverse pollutants, including heavy metals (HM). The detection of heavy metals is necessary to remediate them, which is achieved with biosensors. Initially, these HM were detected using atomic absorption spectroscopy (AAS), emission spectroscopy, mass spectrometry, gas chromatography etc., but these were costly and time consuming which further paved a way for microbe-based biosensors. The development of genetic circuits for microbe-based biosensors has become more popular in recent years for heavy metal detection. In this review, we have especially discussed the various types of genetic circuits such as toggle switches, logic gates, and amplification modules used in these biosensors as they are used to enhance sensitivity and specificity. Genetic circuits also allow for rapid and multiple analyte detection at the same time. The use of microbial biosensors for the detection of HM in the soil as well as the water is also described below. Although with a higher success rate than classical biosensors, these microbial biosensors still have some drawbacks like bioavailability and size of the analyte which are needed to be addressed.

Iron-modified phosphorus- and silicon-based biochars exhibited various influences on arsenic, cadmium, and lead accumulation in rice and enzyme activities in a paddy soil

Contamination of paddy soils with potentially toxic elements (PTEs) has become a severe environmental issue. Application of functionalized biochar for rice cultivation has been proposed as an effective means to reduce environmental risks of these PTEs in paddy soils. This work was undertaken to seek the positive effects of a rice husk-derived silicon (Si)-rich biochar (Si-BC) and a pig carcass-derived phosphorus (P)-rich biochar (P-BC), as well as their Fe-modified biochars (Fe-Si-BC and Fe-P-BC) on the enzyme activity and PTE availability in an As-Cd-Pb-contaminated soil. A rice cultivation pot trial was conducted using these functionalized biochars as soil amendments for the alleviation of PTE accumulation in rice plants. Results showed that Si-BC decreased the concentrations of As in rice grain and straw by 59.4 % and 61.4 %, respectively, while Fe-Si-BC significantly (P < 0.05) enhanced plant growth, increasing grain yield (by 38.6 %). Fe-Si-BC significantly (P < 0.05) elevated Cd and Pb accumulation in rice plants. P-BC enhanced the activities of dehydrogenase, catalase, and urease, and reduced grain-Pb and straw-Pb by 49.3 % and 43.2 %, respectively. However, Fe-P-BC reduced plant-As in rice grain and straw by 12.2 % and 51.2 %, respectively, but increased plant-Cd and plant-Pb. Thus, Fe-modified Si- and P-rich biochars could remediate paddy soils contaminated with As, and enhance the yield and quality of rice. Application of pristine P-rich biochar could also be a promising strategy to remediate the Pb-contaminated paddy soils and limit Pb accumulation in rice.

A critical review on biochar-assisted free radicals mediated redox reactions influencing transformation of potentially toxic metals: Occurrence, formation, and environmental applications

Potentially toxic metals have become a viable threat to the ecosystem due to their carcinogenic nature. Biochar has gained substantial interest due to its redox-mediated processes and redox-active metals. Biochar has the capacity to directly adsorb the pollutants from contaminated environments through several mechanisms such as coprecipitation, complexation, ion exchange, and electrostatic interaction. Biochar's electron-mediating potential may be influenced by the cyclic transition of surface moieties and conjugated carbon structures. Thus, pyrolysis configuration, biomass material, retention time, oxygen flow, and heating time also affect biochar's redox properties. Generally, reactive oxygen species (ROS) exist as free radicals (FRs) in radical and non-radical forms, i.e., hydroxyl radical, superoxide, nitric oxide, hydrogen peroxide, and singlet oxygen. Heavy metals are involved in the production of FRs during redox-mediated reactions, which may contribute to ROS formation. This review aims to critically evaluate the redox-mediated characteristics of biochar produced from various biomass feedstocks under different pyrolysis conditions. In addition, we assessed the impact of biochar-assisted FRs redox-mediated processes on heavy metal immobilization and mobility. We also revealed new insights into the function of FRs in biochar and its potential uses for environment-friendly remediation and reducing the dependency on fossil-based materials, utilizing local residual biomass as a raw material in terms of sustainability.

Immobilization on anionic metal(loid)s in soil by biochar: A meta-analysis assisted by machine learning

Metal pollution in soil has become one of the most serious environmental problems in China. Biochar is one of the most widely used remediation agents for soil metal pollution. However, the literature does not provide a consistent picture of the performance of biochar on the immobilization of anionic metal(loid)s, especially arsenic, in soil. To obtain a baseline understanding on the interactions of metals and biochar, 597 data records on four metal(loid)s (As, Cr, Sb and V) were collected from 70 publications for this meta-analysis, and the results are highlighted below. Biochar has a significant immobilization effect on anionic metal(loid)s in soil and reduces the bioavailability of these metals to plants. Subgroup analysis found that biochar could decrease the potential mobility of Cr, Sb and V, but the immobilization effect on As was not always consistent. Meanwhile, biochar pH and soil pH are the most key factors affecting the immobilization effect. To summarize, biochar can effectively immobilize Cr, Sb and V in soil, but more attention should be given to As immobilization in future applications. By regulating the properties of biochar and appropriate modification, anionic metal(loid)s in soil can be immobilized more effectively. Hence, both of the soil quality and crop quality can be improved.

Modified and pristine biochars for remediation of chromium contamination in soil and aquatic systems

Chromium (Cr) contamination in soil and water poses high toxicity risks to organisms and threatens food and water security worldwide. Biochar has emerged as a promising material for cleaning up Cr contamination owing to biochar's strong capacity to immobilize Cr. This paper synthesizes information on biochar modification for the efficient remediation of Cr contamination in soil and water, and critically reviews mechanisms of Cr adsorption on pristine and modified biochars. Biochar modification methods include physical activation via ball milling or ultraviolet irradiation, chemical activation via magnetization, alkali/acid treatment, nano-fabrication or loading of reductive agents, and biological activation via integrating biochars with microorganisms and their metabolites. Modified biochars often have multi-fold enhancement in Cr adsorption/reduction capacity than pristine biochars. Iron (Fe)-supported magnetic biochars have the most promising Cr removal abilities with high reusability of the biochars. Pre-pyrolysis modification with Fe could load Fe₃O₄ micro-/nanoparticles on biochars, and increase the surface area and electrostatic attraction between chromate anions and biochar surfaces, and reduce Cr(VI) to Cr(III). Post-pyrolysis modification could enrich oxygen-containing functional groups such as CO and -OH on biochar surfaces and promote Cr reduction and adsorption. Future research directions for Cr mitigation using advanced biochar products are discussed in this review.

Goethite-based carbon foam nanocomposites for concurrently immobilizing arsenic and metals in polluted soils

Although different amendments have been used for the immobilization of metals and metalloids in contaminated soils, in most of them there are still important challenges that need to be faced in order to achieve an optimal result. In this work, a new material based on a carbon foam impregnated with goethite nanoneedles has been developed with the aim of evaluating its effect on the mobility and availability of As, Cd, Cu, Pb and Zn in an industrial soil. For this purpose, leaching, sequential extraction and phytotoxicity studies have been carried out. The results were compared with the same carbon foam without goethite impregnation. When the soil was treated with goethite-based carbon foam nanocomposite, the mobility of metal(loid)s was markedly reduced, with the exception of Zn, which showed moderate immobilization. The presence of acid groups on the surface of the carbon foam, together with a high surface area, led to a strong immobilization of pollutants. Moreover, the modification of the foams using goethite nanoneedles, imply that the novel nanocomposite obtained is effective to remediate simultaneously metal and metalloid-polluted soils, without any relevant effect on soil toxicity.

Waste preserved wood derived biochar catalyst for promoted peroxymonosulfate activation towards bisphenol A degradation with low metal ion release: The insight into the mechanisms

The rational disposal of waste preserved wood is of great significance since its embedded metals (Cu, As, and Cr) pose potential threat to environment and human health. In this study, a biochar catalyst derived from waste preserved wood (PWB) was prepared for the degradation of bisphenol A (BPA) via peroxymonosulfate (PMS) activation. The PWB exhibited prominent catalytic degradation capability towards BPA compared with common wood derived biochar (CWB). Further tests and analysis elucidated that both radical species (OH) and non-radical species (¹O₂) were generated by the PWB/PMS system, whereas only ¹O₂ was detected in CWB/PMS system. Specifically, the metal compounds, especially metallic Cu in the PWB activated PMS via radical pathway, and the CO groups in the biochar generated the non-radical pathway, the coexistence of which resulted in higher BPA degradation rate in PWB/PMS system. It was also demonstrated that the heavy metal ion leaching (As and Cr) in PWB/PMS system was negligible. Furthermore, the biochar could effectively inhibit the leakage of oxidized Cu ions. This study provides a novel approach to prepare high-efficient carbocatalysts for organic pollutant degradation in water, which also enables the waste preserved wood with an environmental nondestructive mode of dispatch.

Biochar as environmental armour and its diverse role towards protecting soil, water and air

Biochar has been of considerable importance for various environmental applications in recent years. It has exhibited substantial advantages like favourable structural and surface properties, easy process of preparation and widely available feedstocks. These set of exceptional properties make it an efficient, cost-effective and environment friendly source for diversified elimination of pollutants. The heterogeneity of physico-chemical properties offers a possibility for biochar to optimize its efficacy for targeted applications. This review aims to highlight the critical role that biochar plays in various environmental applications, be it in soil, water or air. In particular the article offers a comprehensive review of the recent research findings and updates related to the diversified role of biochar. Also, the interaction of pollutants with biochar functional groups and the impact of variation of parameters on biochar attribute relevant to specific pollutant removal, modifications, mechanisms involved and competence for such removal has been discussed. Different technologies for production of biochar have also been summarized with an emphasis on post treatment of biochar, such as modification and doping. In addition to this, the underlying gaps in the studies carried out so far and recommendations for future research areas in biochar have also been deliberated.

Elucidating the redox-driven dynamic interactions between arsenic and iron-impregnated biochar in a paddy soil using geochemical and spectroscopic techniques

Iron (Fe)-modified biochar, a renewable amendment that synthetizes the functions of biochar and Fe materials, demonstrates a potential to remediate arsenic (As)-contaminated soils. However, the effectiveness of Fe-based biochar to immobilize As in paddy soils under varying redox conditions (Eh) has not been quantified. We tested the capability of the raw (RBC) and Fe-impregnated (FeBC) biochars to immobilize As in a paddy soil under various Eh conditions (from -400 to +300 mV) using a biogeochemical microcosm system. In the control, As was mobilized (686.2-1535.8 μg L^-1) under reducing conditions and immobilized (61.6-71.1 μg L^-1) under oxidizing conditions. Application of FeBC immobilized As at Eh < 0 mV by 32.6%-81.1%, compared to the control, because of the transformation of As-bound Fe (hydro)oxides (e.g., ferrihydrite) and the formation of complexes (e.g., ternary As-Fe-DOC). Application of RBC immobilized As at Eh < -100 mV by 16.0%-41.3%, compared to the control, due to its porous structure and oxygen-containing functional groups. Mobilized As at Eh > +200 mV was caused by the increase of pH after RBC application. Amendment of the Fe-modified biochar can be a suitable approach for alleviating the environmental risk of As under reducing conditions in paddy soils.

Adsorption and catalytic degradation of organic contaminants by biochar: Overlooked role of biochar's particle size

Biochar (BC) is considered as a promising adsorbent and/or catalyst for the removal of organic contaminants. However, the relationship between the particle size of BC and its adsorption/catalysis performance is largely unclear. We therefore investigated the influence of particle size on the performance of BC pyrolyzed at 300-900 °C in trichloroethylene (TCE) adsorption and persulfate (PS) activation for sulfamethazine (SMT) degradation. The results showed that high-temperature pyrolyzed BC (BC900) presented superior adsorption capacity for TCE and excellent catalytic activity for PS activation to degrade SMT. Compared to 150-250 µm, 75-150 µm and pristine BC900, 0-75 µm BC900 showed the highest TCE adsorption efficiency, which increased by 19.5-62.3%. Similarly, SMT removal by BC900/PS systems also increased from 24.2% to 98.3% with decreasing BC particle size. However, the catalytic activity of BC after grinding was not significantly improved as expected, indicating the properties of biochar was not only controlled by size effect. Characterization measurements proved that small-sized BC tended to have larger specific surface area, more micropores, higher conductivity, rich graphitic domains and surface redox-active functional groups, thus resulting in an enhanced adsorption and catalytic ability of BC.

Pig carcass-derived biochar caused contradictory effects on arsenic mobilization in a contaminated paddy soil under fluctuating controlled redox conditions

Contamination of paddy soils by arsenic (As) is of great concern for human health and the environment. The impact of animal-derived biochar on As mobilization under fluctuating redox conditions in paddy soils has not been studied. Consequently, we investigated the effects of pig carcass-derived biochar (PB) on As (im)mobilization in a contaminated paddy soil under controlled redox potential (Eh) using a biogeochemical microcosm-setup. The addition of PB decreased the concentration of dissolved As at Eh = +100 and +200 mV by 38.7% and 35.4%, respectively (compared to the control), because of the co-precipitation of As with Fe-Mn oxides and the complexation between As and aromatic organic molecules. However, under reducing conditions (Eh = -300 mV), PB increased the dissolved As by 13.5% through promoting reduction and decomposition of As-bearing Fe minerals (e.g., ferrihydrite-As, Fe-humic-As). Under oxidizing conditions (Eh = +250 mV), PB increased the dissolved As by 317.6%, due to the associated increase of pH. We conclude that As mobilization in PB-treated paddy soils is highly affected by Eh. PB can be used to reduce the environmental risk of As under moderately reducing conditions, but it may increase the risk under highly reducing and oxidizing conditions in paddy soils.

Combined use of lime, bentonite, and biochar for immobilization of Cd and mobilization of Se in paddy soil

Remediation of soil contaminated with cadmium (Cd) that can produce rice enriched with selenium (Se) is highly significant for improving the public health in China. A key issue needing resolution in this regard is the simultaneous immobilization of Cd and mobilization of Se. To explore a potential promising method to remediate median-high Se soil that is contaminated by Cd, a potted experiment was conducted, and seven combined amendments (0.03-0.12% lime, 0.03-0.18% bentonite, and 0.3-1.2% biochar of the dry soil weight) were used to immobilize Cd in three paddy soils, in which the concentrations of Cd and Se are 0.46 and 0.45 mg/kg, 1.12 and 0.33 mg/kg, and 2.96 and 0.31 mg/kg, respectively. The soil pH increased by 1.5-2 units after the application of the amendments, and the soil organic carbon (SOC) concentration increased notably with the addition of large quantities of biochar. As the pH and SOC concentration increased, the concentrations of the available Cd in the soil decreased by 35-50%, and the FTIR spectrum showed that O-containing groups and Si-O facilitated the Cd immobilization. The concentration of Cd in brown rice decreased with a decrease in the available Cd. There was no apparent correlation between the Se concentration in the brown rice and the concentration of the available Se in the soil, although the available Se increased by 40-80% after the application of amendments. The accumulation of Se in rice grains was regulated by interactions among the lime, bentonite, biochar, and the soil. An SEM-EDS analysis showed that the biochar particles were covered with bentonite and other soil minerals that could postpone biochar aging and contribute to the longevity of the combined amendments in the soil.

Synthesis of zero-valent iron/biochar by carbothermal reduction from wood waste and iron mud for removing rhodamine B

This study proposes a new process to synthesize zero-valent iron/biochar (Fe⁰-BC) by carbothermal reduction using wood waste and iron mud as raw materials under different temperature. The characterization results showed that the Fe⁰-BC synthesized at 1200 °C (Fe⁰-BC-1200) possessed favorable adsorption capacity with the specific surface area of 103.18 m²/g and that the zero-valent iron (Fe⁰) particles were uniformly dispersed on the biochar surface. The removal efficiency of rhodamine B (RB) was determined to evaluate the performance of the prepared Fe⁰-BC. Fe⁰-BC-1200 presented the best performance on RB removal, which mainly ascribes to that more Fe⁰ particles generated at higher temperature. The equilibrium adsorption capacity reached 49.93 mg/g when the initial RB concentration and the Fe⁰-BC-1200 dosage were 100 mg/L and 2 g/L, respectively, and the pseudo-second-order model was suitable to fit the removal experimental data. LCMC and XRD analyses revealed that the removal mechanism included the physical adsorption of biochar and the redox reaction of Fe⁰. Moreover, copper existing in the iron mud was also reduced to Cu⁰, which was beneficial to catalyze the oxidation of iron; the degradation of RB was promoted at the same time.

Environmental and Health Hazards of Chromated Copper Arsenate-Treated Wood: A Review

Copper chrome arsenate (CCA) water-borne solution used to be widely used to make timber highly resistant to pests and fungi, in particular, wood products designed for outdoor use. Nowadays, CCA is a restricted chemical product in most countries, since potential environmental and health risks were reported due to dermal contact with CCA residues from treated structures and the surrounding soil, as well as the contamination of soils. However, large quantities of CCA-treated timber are still in use in framings, outdoor playground equipment, landscaping, building poles, jetty piles, and fencing structures around the world, thus CCA remains a source of pollutants to the environment and of increasing toxic metal/metalloid exposure (mainly in children). International efforts have been dedicated to the treatment of materials impregnated with CCA, however not only does some reuse of CCA-treated timber still occur, but also existing structures are leaking the toxic compounds into the environment, with impacts on the environment and animal and human health. This study highlights CCA mechanisms and the documented consequences in vivo of its exposure, as well as the adverse environmental and health impacts.

Selecting Bioassay Test Species at the Screening Level of Soil Ecological Risk Assessments

For site-specific soil ecological risk assessments (SERAs), an integrated chemical, ecotoxicological, and ecological analysis needs to be performed. The SERA guidelines of international institutions and countries recommend that a SERA be initiated at the screening level to save time and social economic cost; however, they provide no unified test species for this screening level. This study performed SERAs for field soils and confirmed the importance of selecting bioassay test species that reflect the ecotoxicity of field soils at the screening level. To confirm test species that reflect the ecological risk of field soils, correlation analysis was performed on the results of each bioassay with the integrated ecotoxicological risk index (EtoxRI). Our results showed that soil algae, nematodes, and plants were the most representative species in soil assays, with high correlation coefficients with EtoxRI. The results imply the importance of selecting test species that represent ecological risk for the screening level of SERAs. Based on these findings, when using SERAs, species sensitivity, ecological relevance, and economic aspects should be considered when selecting the bioassay test species.

Whole-Cell Microbial Bioreporter for Soil Contaminants Detection

Anthropogenic activities have released various contaminants into soil that pose a serious threat to the ecosystem and human well-being. Compared to conventional analytical methodologies, microbial cell-based bioreporters are offering a flexible, rapid, and cost-effective strategy to assess the environmental risks. This review aims to summarize the recent progress in the application of bioreporters in soil contamination detection and provide insight into the challenges and current strategies. The biosensing principles and genetic circuit engineering are introduced. Developments of bioreporters to detect and quantify heavy metal and organic contaminants in soil are reviewed. Moreover, future opportunities of whole-cell bioreporters for soil contamination monitoring are discussed.

Application of iron-biochar composite in topsoil for simultaneous remediation of chromium-contaminated soil and groundwater: Immobilization mechanism and long-term stability

This study was aimed to prove the effectiveness and practicability of an integrated technology for simultaneous remediation of Cr-contaminated soil and groundwater. The remediation system was built by pumping Cr-contaminated groundwater into top contaminated soil round after round, enabling the pre-applied iron-biochar composite (Fe-BC) in topsoil to stabilize Cr from both groundwater and soil. Immobilization ability and mechanism of Cr in soil were explored by toxicity characteristic leaching procedure test, scanning electron microscopy-elemental mapping, and X-ray photo spectroscopy. Hydrus-1D software was used to examine the long-term stability of immobilized Cr in soil. Results showed that Fe-BC-amended soil could remove about 71% Cr from contaminated groundwater. Meanwhile, Cr from both groundwater and soil was simultaneously immobilized in topsoil, leachability of Cr in which was reduced by over 81%. The immobilization of Cr in soil was attributed to the reduction of Cr(VI) into Cr(III) to form stable Cr_xFe_(1-x)(OH)₃. After remediation, the average transport rate of Cr in the soil profile was only 0.420 cm y^-1 along with the local rainfall. Our study demonstrated that integrated technology could effectively remove Cr from groundwater and stabilize Cr in soil and the simultaneous remediation target for both soil and groundwater reached.

Enhanced copper removal from contaminated kaolinite soil by electrokinetic process using compost reactive filter media

Electrokinetic (EK) remediation is a promising technology for soil decontamination, although basic pH in the soil close to cathode has constrained EK effectiveness due to heavy metal precipitation. This study aimed to enhance copper removal from kaolinite soil by integrating EK with compost (C) as recyclable reactive filter media (RFM) for the first time. Compost placed near the cathode served as an adsorbent to bind copper ions while buffering the advancement of the alkaline front in soil. The total copper removal rate increased from 1.03% in EK to 45.65% in EK-100%C under an electric potential of 10 V. Further experiments conducted by using biochar (BC) and compost/biochar (C + BC) mixture RFM at different ratios showed total Cu removal efficiency decreasing as EK-100%C > EK-(10%BC + 90%C) > EK-(20%BC + 80%C) > EK-(30%BC + 70%C) > EK. The application of a constant electric current of 20.00 mA further enhanced copper removal to 84.09% in EK-100%C although did not show significant enhancement in EK-(BC + C). The compost RFM was regenerated by acid extraction and then reused twice, achieving a total removal of 74.11%. The findings demonstrated compost as a promising and reusable RFM for the efficient removal of copper in contaminated soil.

Stabilization of Soil Arsenic with Iron and Nano-Iron Materials: A Review

Soil arsenic (As) contamination is an important environmental problem, and chemical stabilization is one of the major techniques used to remediate soil As contamination. Iron and iron nanoparticle materials are widely used for soil As stabilization because they have one or more of the following advantages: high adsorption capacity, high reduction capacity, cost effectiveness and environmental friendliness. Therefore, this review introduces the stabilization of soil As with iron and iron nanoparticles, including zero-valent iron, iron oxides/hydroxides, some iron salts and Fe-based binary oxides and the nanoparticles of these iron materials. The mechanism of chemical soil As stabilization, which involves adsorption and the coprecipitation process, is discussed. The factors affecting the chemical stabilization process are presented, and challenges to overcome in the future are also discussed in this review.

Effect of neutralizing agents on the type of As co-precipitates formed by in situ Fe oxides synthesis and its impact on the bioaccessibility of As in soil

The bioaccessibility of heavy metals in soil is closely related to their potential risk. Therefore, developing techniques for reducing it needs considerable attention. In this study, we aimed to co-precipitate soil As(V) through an in situ formation of Fe oxides, thereby reducing its bioaccessibility. Soil As(V) was co-precipitated by introducing 2% Fe-nitrate (w/w) and 30% water (v/w) into soil at pH ~7. Two different neutralizing agents (NaOH and CaO) were used to induce the precipitation of Fe oxides, and their effects on the speciation of As were investigated. In all the stabilized soils, the exchangeable As fraction decreased, and the fraction of As bound to amorphous Fe oxides increased by a factor of more than 1.4. In contrast, a marked decrease in bioaccessibility of As was achieved using NaOH (40% to 7%). X-ray absorption spectroscopy analysis demonstrated that highly bioaccessible forms of calcium iron arsenate (yukonite and arseniosiderite) could be generated in CaO-stabilized soil. Our study found that neutralizing agents may play an important role in stabilizing As(V) and lowering its bioaccessibility through determining the type of formed Fe oxides in soil.

Hazardous wastes treatment technologies

A review of the literature published in 2019 on topics related to hazardous waste management in water, soils, sediments, and air. The review covered treatment technologies applying physical, chemical, and biological principles for the remediation of contaminated water, soils, sediments, and air. PRACTICAL POINTS: This report provides a review of technologies for the management of waters, wastewaters, air, sediments, and soils contaminated by various hazardous chemicals including inorganic (e.g., oxyanions, salts, and heavy metals), organic (e.g., halogenated, pharmaceuticals and personal care products, pesticides, and persistent organic chemicals) in three scientific areas of physical, chemical, and biological methods. Physical methods for the management of hazardous wastes including general adsorption, sand filtration, coagulation/flocculation, electrodialysis, electrokinetics, electro-sorption ( capacitive deionization, CDI), membrane (RO, NF, MF), photocatalysis, photoelectrochemical oxidation, sonochemical, non-thermal plasma, supercritical fluid, electrochemical oxidation, and electrochemical reduction processes were reviewed. Chemical methods including ozone-based, hydrogen peroxide-based, potassium permanganate processes, and Fenton and Fenton-like process were reviewed. Biological methods such as aerobic, anoxic, anaerobic, bioreactors, constructed wetlands, soil bioremediation and biofilter processes for the management of hazardous wastes, in mode of consortium and pure culture were reviewed. Case histories were reviewed in four areas including contaminated sediments, contaminated soils, mixed industrial solid wastes and radioactive wastes.

Field evaluation of one Cu-resistant somaclonal variant and two clones of tobacco for copper phytoextraction at a wood preservation site

A Cu-resistant somaclonal tobacco variant (NBCu 10-8-F1, C1), its BaG mother clone (C3), and the FoP tobacco clone (C2) were cultivated at a wood preservation site on Cu-contaminated soils (239-1290 mg Cu kg-1 soil range) and an uncontaminated control site (CTRL, 21 mg Cu kg-1) to assess their shoot DW yields and potential use for bioavailable Cu stripping. The Cu concentration in the soil pore water varied between 0.15 and 0.84 mg L-1. Influences of Cu exposure and soil treatments, i.e., untreated soil (Unt), soils amended with compost and either dolomitic limestone (OMDL) or zerovalent iron grit (OMZ), on plant growth and shoot ionome were determined. All transplants survived and grew even at high total soil Cu. Shoots were harvested after 3 months (cut 1). Subsequently, bottom suckers developed and were harvested after 2 months (cut 2). Total shoot DW yield (cuts 1 + 2) varied between 0.8 and 9.9 t DW ha-1 year-1 depending on tobacco cultivars, soil treatments, and soil Cu exposure. It peaked for all cultivars in the OMDL plots at moderate Cu exposure (239-518 mg kg-1 soil), notably for the C2 plants. Cut 2 contributed for 11-43% to total shoot DW yield. Increase in shoot DW yield diluted shoot Cu concentration. At low Cu exposure, total shoot Cu removal peaked for the variant. At moderate Cu exposure, shoot Cu concentrations were similar in all cultivars, but total shoot Cu removal was highest for the C2 plants. At high Cu exposure (753-1140 mg kg-1), shoot Cu concentrations peaked for the C2 plants in the Unt plots, the C1 and C2 plants in the OMZ plot, and the C3 ones in the OMDL plots. Shoot Cu removal (in g Cu ha-1 year-1) ranged from 15.4 (C2 on the CTRL soil) to 261.3 (C2 on moderately contaminated OMDL soils). The C2 plants phytoextracted more Cu than the C1 and C3 ones in the Unt plots and in the OMDL plots at moderate Cu exposure. In the OMDL plots with high Cu exposure, shoot Cu removal was highest for the C1 plants. Soil amendments improved shoot Cu removal through increase in either shoot DW yield (OMDL-3-fold) or shoot Cu concentration (OMZ-1.3-fold). Increased shoot Cu concentration induced an ionome imbalance with increased shoot Al, Fe, B, and Mg concentrations and decreased P and K ones. Copper concentrations in plant parts varied in decreasing order: roots > leaves > inflorescence (cymes including seeds) > stem, whereas Cu removal ranked as roots > stem = leaves > inflorescence.

Ecological risk assessment (ERA) based on contaminated groundwater to predict potential impacts to a wetland ecosystem

To assess the ecological risk resulting from an accidental gasoline spill upstream from a wetland, groundwater and sediment sampling was carried out during two campaigns at the 48th and 52nd months after the spill had occurred. In total, 21 groundwater monitoring wells in the affected area were sampled plus an additional reference well located upstream from the accident location. Seven sediment sampling points were selected inside the wetland, plus a reference point upstream from the accident. Physicochemical parameters, BTEX (benzene, toluene, ethylbenzene, m-xylene, p-xylene and o-xylene) and metal concentrations were analysed to estimate the chemical risk. Acute (Allivibrio fischeri, Daphnia similis, Hyalella azteca) and chronic (Artemia salina and Desmodesmus subspicatus) toxicity assays were performed with groundwater and sediments elutriate to determine the ecotoxicological risk. Results from groundwater indicated an extreme chemical level of risk in14 out of 21 monitoring wells. These 14 wells also exhibited free-phase gasoline and lead (Pb) concentrations above the threshold values adopted by this study. The presence of Pb, however, could not be associated with the gasoline accident. High acute and chronic toxicities were reported for the majority of wells. Conversely, the risks associated with the sediments were considered low in most sampling points, and the ecotoxicity found could not be related to the presence of gasoline. Groundwater flow modelling results have evidenced the migration of the contamination plume towards the wetland. Thus, to prevent contamination from reaching the protected area, more effective groundwater clean-up techniques are still required.

Reducing geogenic arsenic leaching from excavated sedimentary soil using zero-valent iron amendment followed by dry magnetic separation: A case study

Although the deep-layer sedimentary soils excavated from construction sites contain low level of geogenic arsenic (As), remediation is necessary when the As leachability exceeds the environmental standard (10 μg/L) in Japan. In this study, the zero-valent iron (ZVI) amendment followed by dry magnetic separation (ZVI-DMS) was implemented for the treatment of a geogenic As-contaminated alkaline sedimentary soil (pH 8.9; 7.5 mg/kg of total As; 0.33 mg/kg of water-extractable As). This technology involves pH adjustment (adding H₂SO₄), ZVI addition, water content reduction (adding water adsorbent CaSO₄·0.5H₂O), and dry magnetic separation. The short-term and long-term As leachability before and after treatment was compared using sequential water leaching tests (SWLT). The results illustrated that As could be removed from the bulk soil through the magnetic separation of As-ZVI complexes, although the amount was limited (about 2% of total As). Moreover, immobilization played a dominant role in suppressing As leaching. The H₂SO₄ addition decreased pH to a circumneutral range and thereby suppress As release. The CaSO₄·0.5H₂O addition also contributed to the pH decrease and reduced As leachability. Besides, CaSO₄·0.5H₂O-dissolution released Ca²⁺ that favored As adsorption, and enhanced dissolved organic carbon (DOC) coagulation that decelerated As dissolution. SWLT results indicated that As leachability from remediated soil satisfied the environmental standard (10 μg/L) in both short-term and long-term perspective. However, the secular stability of treated soil deserves more attention due to the easy re-release of As caused by As-bearing framboidal pyrite oxidation. Additionally, during ZVI-DMS process, there is a need to scientifically decide the dosage of ZVI to avoid excessive addition. Our results demonstrated that ZVI-DMS technology could be a promising remediation strategy for geogenic As contaminated sedimentary soils/rocks.

Prospect of phytoremediation combined with other approaches for remediation of heavy metal-polluted soils

Accumulation of heavy metals in agricultural soils due to human production activities-mining, fossil fuel combustion, and application of chemical fertilizers/pesticides-results in severe environmental pollution. As the transmission of heavy metals through the food chain and their accumulation pose a serious risk to human health and safety, there has been increasing attention in the investigation of heavy metal pollution and search for effective soil remediation technologies. Here, we summarized and discussed the basic principles, strengths and weaknesses, and limitations of common standalone approaches such as those based on physics, chemistry, and biology, emphasizing their incompatibility with large-scale applications. Moreover, we explained the effects, advantages, and disadvantages of the combinations of common single repair approaches. We highlighted the latest research advances and prospects in phytoremediation-chemical, phytoremediation-microbe, and phytoremediation-genetic engineering combined with remediation approaches by changing metal availability, improving plant tolerance, promoting plant growth, improving phytoextraction and phytostabilization, etc. We then explained the improved safety and applicability of phytoremediation combined with other repair approaches compared to common standalone approaches. Finally, we established a prospective research direction of phytoremediation combined with multi-technology repair strategy.

Facilitated transport of nTiO2-kaolin aggregates by bacteria and phosphate in water-saturated quartz sand

The soil major component of clay plays an important role in governing the fate and transport of engineered nanomaterials (e.g., the most commonly used titanium dioxide nanoparticles; nTiO₂) in the subsurface environments via forming nTiO₂-clay aggregates. This research is designed to unravel the interplay of naturally-occurring bacteria (Escherichia coli) and phosphate on the transport and retention of nTiO₂-kaolin aggregates in water-saturated porous media. Our results showed that nTiO₂-nTiO₂ homoaggregates and nTiO₂-kaolin heteroaggregates dominated in the nTiO₂-kaolin nanoaggregate suspension. Transport of nTiO₂-kaolin aggregates was enhanced with the copresence of E. coli and phosphate, particularly at the low pH of 6.0. This effect is due to the greater adsorption of phosphate and thus the greater enhancement in repulsive interaction energies between aggregates and sand grains at pH 6.0 (vs. pH 9.0). The charged "soft layer" of E. coli cell surfaces changed the aggregation state and the heterogeneous distribution of nTiO₂-kaolin aggregates, and subsequently stabilized the nTiO₂-nTiO₂ homoaggregates and nTiO₂-kaolin heteroaggregates via TEM-EDX measurements and promoted the physical segregation between the aggregates (separation distance = 0.486 vs. 0.614 μm without vs. with the presence of E. coli) via 2D/3D AFM identifications, both of which caused greater mobility of nTiO₂-kaolin aggregates with the presence of E. coli. Nonetheless, transport of nTiO₂-kaolin aggregates was lower with the copresence of E. coli and phosphate vs. the singular presence of phosphate due to the competitive adsorption of less negatively charged E. coli (vs. phosphate) onto the aggregates. Taken altogether, our findings furnish new insights into better understanding the fate, transport, and potential risks of nTiO₂ in real environmental settings (soil and sediment aquifer) where clay, bacteria, and phosphate ubiquitously cooccur.

The bioaccessibility and fractionation of arsenic in anoxic soils as a function of stabilization using low-cost Fe/Al-based materials: A long-term experiment

Arsenic (As)-contaminated soils occur widely worldwide. In the present study, three low-cost Fe/Al-based materials, including red soil (RS), sponge iron filter (SIF) and Al-based water treatment sludge (WTS), were applied as amendments to remediate As-contaminated soils under anoxic conditions. After 180 d of incubation, the proportion of the sum of nonspecifically absorbed As (F1) and specifically absorbed As (F2) to the total As was reduced by 6%, 52% and 13% with 5% of RS, SIF and WTS addition, respectively, compared to the control soil (31%). The results showed that among the three amendments, SIF was the most effective at decreasing As bioaccessibility in soils. Compared with RS and WTS, SIF intensified the decrease of labile fractions and the increase of unlabile fractions, and the redistribution of the amorphous oxide-bound fraction (F3) and crystalline hydrous oxide-bound fraction (F4) occurred in the SIF-amended soil. Moreover, the As stabilization processes were divided into two stages in the control and RS-amended soil, while the processes were divided into three stages in both SIF- and WTS-treated soil. The As stabilization processes in all treated soils were characterized by the transformation of labile fractions into more immobilizable fractions, except for F4 transforming into F3 in the first stage in SIF-amended soil. Correspondingly, inner-surface complexation and occlusion within Fe/Al hydroxides were the common driving mechanisms for the transformation of As fractions. Therefore, taking into consideration the results of this study, SIF could be a more promising alternative than the other two materials to passivate As in anoxic soils.

Assessment of biochar and/or nano zero-valent iron for the stabilisation of Zn, Pb and Cd: A temporal study of solid phase geochemistry under changing soil conditions

The remediation of a soil contaminated with Zn, Pb and Cd was tested by using biochar (BC), nano zero-valent iron (nZVI) and a combination of these two (BC + nZVI). Each amendment was individually applied to the soil at 2 wt%. We tested the influence of (i) the used amendments, (ii) time, and (iii) soil moisture conditions on the metal availability and soil physico-chemical parameters using various extraction methods, as well as soil pore water samplings. We found that metal availability was mainly affected by pH under the influence of time and water content. Among the tested treatments, BC was the most successful, resulting in the lowest amounts of the target metals in the pore water and the smallest temporal changes in metal concentrations and pH in the soil. The use of nZVI efficiently decreased water-extractable Pb in the short- and long-term. The BC + nZVI treatment also yielded promising results regarding the immobilisation of the studied metals. Time provoked a general decrease in pH, which occasionally increased the available metal concentrations. Raising the soil water content increased the pH and subsequently lowered the available metal concentrations in the pore water. The mechanisms of metal stabilisation were further investigated by SEM/EDS. The results indicated that the used soil amendments enhanced the binding of Zn, Pb, and Cd on Fe/Mn/Al oxides/hydroxides, which in turn resulted in the stabilisation of the target metals.

Influence of amendments on metal environmental and toxicological availability in highly contaminated brownfield and agricultural soils

The immobilizing effects of wood biochar (BW2%) and iron grit (Z1%) applied alone or in combination (BW2% + Z1%) to agricultural (M750) and brownfield (MAZ) soils highly contaminated by metals were assessed in a greenhouse experiment. The results showed that Z1% and BW2% + Z1% were the most efficient amendments to reduce Cd, Cu, Pb, and Zn mobility, environmental availability, and phytoavailability in the M750 soil. The oxidation of Z1% allowed part of the Cu and Zn pools present in exchangeable or carbonate-bound forms (labile fraction) to complex in less mobile forms. In this soil, the metal chemical extractions (0.01 M CaCl₂ and 0.05 M EDTA) and the DGT (diffusive gradient in thin films) devices to assess metal in soil solution and soil pore water (SPW) also highlighted the immobilizing characteristic of Z1%. In most cases, the addition of BW2% to Z1% (BW2% + Z1%) did not improve this effect, except for the dissolved Pb and Zn concentrations in the M750 soil solution. It was also observed that Cd, Pb, and Zn passed throughout DGT mimicking the biological cell membrane were reduced by all amendments of the M750 soil corroborating metal concentrations measured in rye grass shoots. In the MAZ soil, metals were less available as shown by their low extractability rate, low capacity of metal resupply from the solid phase to pore water, and low phytoavailability. The poor metal availability could be explained by the high levels of carbonate and organic matter contents in this soil. Nevertheless, a decrease of the Cu environmental availability and the Cu concentrations in rye grass shoots grown on the MAZ soil was also observed in the soil amended with Z1% alone or in combination with BW2%. From a health point of view, the most effective amendment to reduce human exposure through ingestion of soil particles for the M750 and MAZ soils was BW2% for Cd and BW2% + Z1% for Pb. However, the presence of rye grass minimized the amendments' beneficial effects.

Biochar enhanced microbial degradation of 17β-estradiol

Steroid estrogens (SEs), especially 17β-estradiol (E2), can be a serious threat to the health of organisms. The removal of E2 from the natural environment is mainly carried out by microbial degradation partly mediated by biochar, which contains quinone structures. In this study, reed straw biochar samples made at four different heat treatment temperatures (HTTs) were used to mediate E2 microbial degradation by Shewanella oneidensis MR-1. The removal efficiency of E2 (95%) was highest in the presence of HTT - 500 °C biochar under anaerobic conditions after 120 h of microbial degradation. The effect of biochar on promoting microbial degradation was far more superior under anaerobic conditions than under aerobic conditions. The redox-activity and types of surface functional groups of biochar reveal that biochar can accept electrons generated by microorganisms in a timely manner. This mechanism promotes the metabolic process of cells and microbial degradation of E2 (exponential increase). Biochar particles rather than biochar-derived water-soluble organic compounds are responsible for this stimulating effect. These results highlight the impact that biochar has on microbial degradation of trace pollutants in a natural environment.

Activation of peroxydisulfate by nanoscale zero-valent iron for sulfamethoxazole removal in agricultural soil: Effect, mechanism and ecotoxicity

In this study, peroxydisulfate (PDS) was successfully activated by nanoscale zero-valent iron (nZVI) for the degradation of sulfamethoxazole (SMX, antibiotic frequently detected in the environment) in agricultural soils. The results indicated that the degradation of SMX was affected by the nZVI dose, the ratio of SMX/PDS, the ratio of soil/water and reaction temperature, and in cinnamon soils 87.6% of SMX degradation can be achieved within 4 h at 30 °C when the initial nZVI dose was 0.03 g g^-1 soil, the molar ratio of SMX/PDS = 1/75 and the soil/water = 1/1. The results of radical scavenger experiments and electron spin resonance (ESR) tests showed that hydroxyl radical (OH) was the dominant reactive species in this system. The ecotoxicity tests of the soil by germination test, luminescent bacteria experiment and enzyme activity test indicated that the ecotoxicity of soil after treatment was obviously lower than the contaminated soil. In addition, there was almost no effect on plant growth when compared with original soil. Furthermore, this system exhibited a great degradation capacity for SMX in different types of agricultural soils, and the degradation efficiencies of SMX in other four soils were 90.6% (yellow brown earths), 80.8% (brown earths), 86.5% (black soils) and 96.1% (red earths), respectively. This work provides an optional method for agricultural soil pollution control.

AsChip: A High-Throughput qPCR Chip for Comprehensive Profiling of Genes Linked to Microbial Cycling of Arsenic

Arsenic (As) is a ubiquitous toxic element adversely affecting human health. Microbe-mediated cycling of As is largely mediated by detoxification and energy metabolism in microorganisms. We here report the development of a novel high-throughput qPCR (HT-qPCR) chip (AsChip) for comprehensive profiling of genes involved in microbial As cycling (here collectively termed "As genes"). AsChip contained 81 primer sets targeting 19 As genes and the 16S rRNA gene as a reference gene. Gene amplicon sequencing showed high identity (>96%) of newly designed primers corresponding to their targets. AsChip displayed high sensitivity (plasmid template serial dilution test; r = -0.99), with more than 96% of all PCR assays yielding true positive signals. R² coefficients for standard curves and PCR amplification efficiencies averaged 0.98 and 0.99, respectively. A high correlation between C_T values obtained by AsChip and conventional qPCR was obtained ( r = 0.962, P < 0.001). Finally, we successfully applied AsChip on soil samples from a chromium-copper-arsenic-contaminated field site and identified diverse As genes with total abundance average of 0.4 As gene copies per 16S rRNA. Our results indicate that AsChip constitutes a robust tool for comprehensive quantitative profiling of As genes in environmental samples.