Fate and effects of polyethylene terephthalate (PET) microplastics during anaerobic digestion of alkaline-thermal pretreated sludge

Microplastics in an anaerobic digester treating sewage sludge: Occurrence and factors affecting their identification with Raman spectroscopy

Significant share of microplastics entering wastewater treatment is accumulated in sewage sludge, which is commonly treated by anaerobic digestion. The digestate is typically separated to solid and liquid fractions, and the solid fraction is often land-applied. However, the division of microplastics between these fractions is poorly understood. Thus, we investigated the occurrence of microplastics (>20 μm) at an anaerobic digester and the subsequent solid-liquid separation. Sewage sludge and digestate exhibited 7600 ± 6800 and 7200 ± 1100 microplastics per g dry weight, respectively, indicating that anaerobic digestion can decrease the fluctuation in microplastics' occurrence in sewage sludge. The microplastic flow was predominantly directed to the solid fraction, while the liquid fraction carried about 1 % of the microplastics, mostly polymers with low density (polyethylene and polypropylene). We also investigated factors affecting microplastics' identification by Raman spectroscopy. Microplastic degradation and presence of organic matter after oxidative digestion in the sample preparation, and anaerobic digestion of sewage sludge affected the spectra of different microplastics. For polyethylene and polypropylene, these changes did not interfere with recognizing their characteristic peaks, allowing high-certainty identification. In contrast, polyamide identification was notably compromised as signal-to-noise ratio can be deteriorated and natural organic matter can be misidentified as polyamide.

Bio-Aging of polyethylene during anaerobic and aerobic digestion

Presence of microplastics (MPs) in wastewater treatment plants (WWTPs) require scrutiny from two perspectives: impact of MPs on treatment and on MPs themselves. Accordingly, this study investigates the impact of high-density polyethylene (HDPE) and low-density polyethylene (LDPE) on mesophilic aerobic and anaerobic digestion, with their concurrent characterization to discern MP biodegradation following digestion. HDPE having UV-stabilizer remains unchanged, whereas additive-free LDPE bio-ages, in both cases. On the flip side, HDPE negatively impacts anaerobic (i.e., 26 % reduction in methane) but not aerobic digestion, while LDPE affects neither. The very high LDPE doses used in our study (300 mg PE/g TS) yielding no negative impact on either aerobic or anaerobic digestion is notable. Lastly, bio-aging potential of PE is closely linked with amorphous/crystalline structure and presence/absence of additives. Such factors may affect microbial colonization, resulting in physical/chemical changes on the surface of PE and on digester operation.

How does alkaline-thermal pretreatment followed by anaerobic digestion affect the content of polyethylene terephthalate and polyamide 66 microplastics?

Microplastics (MPs) are ubiquitous and increasing in quantity, causing raising concern. Wastewater treatment plants (WWTPs) are a point source for both aquatic environments and soil, through the use of sludge in agriculture. Understanding the fate of MPs within the wastewater and sludge lines of a treatment plant and, possibly, enhancing their removal will improve the safe reuse of sludge and water effluent and the wastewater biorefinery concept application. This study investigates the effects of alkaline-thermal pretreatment of sludge, followed by anaerobic digestion, on the physical and chemical characteristics of polyethylene terephthalate (PET) and polyamide 66 (PA(66)) contained. Experiments were conducted to evaluate the influence of different NaOH concentrations, temperatures, and reaction times on the degradation of the MPs in anaerobic digestion. PET MPs exhibited relevant mass reduction and structural changes in relation to the NaOH concentration and temperature. PA(66) MPs showed limited chemical alterations, indicating higher resistance to degradation. Batch anaerobic digestion tests of pretreated samples did not modify them further. Chemical characterization of MPs was performed using both Attenuated Total Reflectance-Fourier Transform Infrared spectroscopy (ATR-FTIR) and Focal Plane Array-Fourier Transform-Imaging-Micro-Spectroscopy (FPA-μFTIR-Imaging), revealing distinct trends between surface-level and bulk material changes in the MPs. The results highlighted that ATR-FTIR recorded lower carbonyl index values compared to FPA-μFTIR-Imaging. These findings emphasized the importance of using complementary analytical techniques to thoroughly understand MPs degradation. The outcomes suggest that tailored pretreatment strategies are essential to enhance MPs removal in WWTPs, ensuring safer sludge reuse within a circular economy framework.

Dissecting the effects of co-exposure to microplastics and sulfamethoxazole on anaerobic digestion

Microplastics (MPs) and antibiotics are frequently and simultaneously detected in sewage and sludge, raising global concerns in recent years. However, their combined effects on anaerobic digestion (AD) remain unclear. Herein, we evaluated the effects of the combinations of different MPs (i.e., polyethylene, polystyrene, polyvinyl chloride and polyethylene terephthalate) with sulfamethoxazole (SMX) on AD performance and microbial communities. The combined stress slightly decreased the chemical oxygen demand removal rate and total gas/methane production. Furthermore, co-exposure to MPs and SMX visibly changed the anaerobic sludge morphology during AD, reduced the methanogen activity, and increased the residual propionic acid concentration versus a control. The decreased relative abundances of Euryarchaeota ranged from 1.88% to 4.63% in the experimental groups compared with CK, suggesting that the microbial communities were inevitably affected by exposure to SMX alone or combined MPs/SMX. Interestingly, among the top 50 genera, only two were negatively related to a few antibiotic resistance genes, implying that sludge exhibited widespread multiple resistances. The correlation analysis between the MPs and microbial communities suggested that the MP properties, such as the aperture-desorption of MPs, may impact the microbial variations. This study will contribute to a deeper understanding of the impact of coexisting MPs/SMX on AD.

A review of methods for mitigating microplastic contamination in biosolids from wastewater treatment plants before agricultural soil application

Wastewater treatment plants (WWTP) are recognized as major sources of microplastic (MP) particles in terrestrial environments, particularly in agricultural soils through biosolids application. While many reviews have focused on the distribution, detection, and mitigation of MPs in wastewater effluent to limit their discharge into oceans, our understanding of methods to mitigate biosolid contamination remains limited. This review focuses on methods for mitigating MPs contamination in biosolids at various intervention points, including sources, WWTP including the primary and secondary treatment stages where sludge is generated, and post-contamination. These methods are categorized as physical, physicochemical, and biological approaches, and their advantages and limitations are discussed. For instance, physicochemical methods, especially froth flotation, are cost-effective but are hindered by contaminants and reagents. Physical methods like microfibre filtration devices (MFD) are safe but their efficiency depends on the filter pore size and design. Biological methods, particularly microbial degradation, are limited by the varying efficiencies of microorganisms in breaking down MPs and the extended time required for their effective degradation. Other physical methods including dissolved air flotation, and ultrasonication already exist in WWTPs but may require retrofitting or optimization to enhance MP removal from biosolids. As each method inherently has limitations, the key to achieving MP-free biosolids, and thus preventing their release into agricultural soil, lies in integrating these methods through multi-coupling strategies.

Microbial strategies for effective microplastics biodegradation: Insights and innovations in environmental remediation

Microplastics (MPs), diminutive yet ubiquitous fragments arising from the degradation of plastic waste, pervade environmental matrices, posing substantial risks to ecological systems and trophic dynamics. This review meticulously examines the origins, distribution, and biological impacts of MPs, with an incisive focus on elucidating the molecular and cellular mechanisms underpinning their toxicity. We highlight the indispensable role of microbial consortia and enzymatic pathways in the oxidative degradation of MPs, offering insights into enhanced biodegradation processes facilitated by innovative pretreatment methodologies. Central to our discourse is the interplay between MPs and biota, emphasizing the detoxification capabilities of microbial metabolisms and enzymatic functions in ameliorating MPs' deleterious effects. Additionally, we address the practical implementations of MP biodegradation in environmental remediation, advocating for intensified research to unravel the complex biodegradation pathways and to forge effective strategies for the expeditious elimination of MPs from diverse ecosystems. This review not only articulates the pervasive challenges posed by MPs but also positions microbial strategies at the forefront of remedial interventions, thereby paving the way for groundbreaking advancements in environmental conservation.

Plastic film from the source of anaerobic digestion: Surface degradation, biofilm and UV response characteristics

This study simulates a major environmental scenario involving "organic fertilizer source" plastics, by exploring the key factors influencing the changes in plastic-films during anaerobic digestion (AD), as well as the responses of the anaerobically digested plastics to ultraviolet (UV) radiation exposure. The results demonstrate that the degradation effect of AD on plastics is reflected by their yellowish and ruptured appearance, slightly worn surfaces, hardening and opacity, and fragmentation. AD significantly increases the content of oxygen-containing functional groups and the degree of unsaturation in plastic films, with thermophilic temperature processes proving more effective than those conducted at mesophilic temperatures. Exposure to UV light has been found to amplify the degradative effects, suggesting the potential cumulative impact of AD and UV. Both AD and UV irradiation reduced the hydrophilicity of plastics. In particular, the hydrophobicity of polylactic acid films was completely disrupted under overlay-exposure. Furthermore, microbial populations on plastic surfaces were mainly bacterial. These bacterial populations were primarily influenced by temperature, and moderately by the plastic types. In contrast, archaea were predominantly affected by both temperature and digested substrate. This study offers a theoretical foundation for strategies aimed at preventing and controlling plastic pollution derived from organic fertilizers.

Fate and effect of Polyamide-6 microplastics in mesophilic and thermophilic anaerobic digestion

Research has demonstrated that depending on the type and concentration, microplastics affect anaerobic digestion (AD). Owing to the high abundance of polyamide-6 (PA6) in wastewater treatment plants and limited understanding of its behavior, this study investigates PA6 microplastics' effect in AD. Biochemical methane potential experiments were performed under mesophilic (35 °C) and thermophilic (55 °C) conditions using PA6 at concentrations from 0 to 200 particles/g total solids (TS). Under both conditions, methane production increased in the highest (200 particles/g TS) PA6-dosed reactors, with thermophilic conditions having a statistically significant effect. Methane yield increased from 403.1 ± 5.3 mL/g VS to 436.6 ± 9.2 mL/g VS under thermophilic and from 332.1 ± 1.5 to 340.6 ± 6.6 mL/g VS under mesophilic conditions for the 200 particles/g TS dose, corresponding to increases of 8.3% and 2.6% respectively. PA6 crystallinity decreased from 32.8% to 27.1% and 26.8%, corresponding to decreases of 17.4% in mesophilic and 18.2% in thermophilic reactors compared to pristine control. Similarly, crystallinity decreased in PA6 microplastics collected from abiotic reactors, with thermophilic conditions showing a greater effect. The carbonyl index (CI) values were similar between biotic and abiotic reactors, but PA6 from all reactors had significantly higher CI than pristine PA6, suggesting abiotic factors also affect carbonyl bonds. Additionally, an increase in average PA6 mass was observed for mesophilic and thermophilic conditions by 22.0 % and 23.0 %, respectively. The study shows that temperature and other abiotic factors, like sludge chemistry, significantly influence the fate and effect of PA6 microplastics in digesters. Including abiotic reactors seems crucial for a full understanding of the impact of microbial and non-microbial factors in microplastic studies in the AD process. Studying the effects of microplastics on AD is only one part of the picture, whereas simultaneously examining their fate in digestion is necessary for a complete understanding.

Degradation of PET microplastic particles to monomers in human serum by PETase

More than 8 billion tons of plastic waste has been generated, posing severe environmental consequences and health risks. Due to prolonged exposure, microplastic particles are found in human blood and other bodily fluids. Despite a lack of toxicity studies regarding microplastics, harmful effects for humans seem plausible and cannot be excluded. As small plastic particles readily translocate from the gut to body fluids, enzyme-based treatment of serum could constitute a promising future avenue to clear synthetic polymers and their corresponding oligomers via their degradation into monomers of lower toxicity than the material they originate from. Still, whereas it is known that the enzymatic depolymerization rate of synthetic polymers varies by orders of magnitude depending on the buffer and media composition, the activity of plastic-degrading enzymes in serum was unknown. Here, we report how an engineered PETase, which we show to be generally trans-selective via induced fit docking, can depolymerize two different microplastic-like substrates of the commodity polymer polyethylene terephthalate (PET) into its non-toxic monomer terephthalic acid (TPA) alongside mono(2-hydroxyethyl)terephthalate (MHET) in human serum at 37 °C. We show that the application of PETase does not influence cell viability in vitro. Our work highlights the potential of applying biocatalysis in biomedicine and represents a first step towards finding a future solution to the problem that microplastics in the bloodstream may pose.

Investigation of thermal alkaline pretreatment of primary and waste activated sludge on the energy efficiency of sludge digestion

Because of the naturally limited anaerobic degradability and limited biogas yield of raw sludge (RS), this study aims to increase the biogas production of primary sludge (PS) and waste activated sludge (WAS) by the integration of thermal alkaline process (TAP). PH 11 is confirmed to be the most suitable pH value for the TAP of both sludges. Moreover, with the pretreatment at pH 11 and 160 °C (6 bar) for 30 min, the investigated PSs and WASs achieved an increased biogas production of up to 81 % and 72 %, respectively. The improved net electricity production of WASs after TAP varied between 15-43 % compared to conventional WAS digestion. However, the TAP of PS at pH 11 enhanced the biogas production by 1-81 %, which did not constantly contribute to an improved net electricity production.

Entry pathways determined the effects of MPs on sludge anaerobic digestion system: The views of methane production and antibiotic resistance genes fates

Sludge is one of the primary reservoirs of microplastics (MPs), and the effects of MPs on subsequent sludge treatment raised attention. Given the entry pathways, MPs would exhibit different properties, but the entry pathway-dependent effect of MPs on sludge treatment performance and the fates of antibiotic resistance genes (ARGs), another high-risk emerging contaminant, were seldom documented. Herein, MPs with two predominant entry pathways, including wastewater-derived (WW-derived) and anaerobic digestion-introduced (AD-introduced), were used to investigate the effects on AD performance and ARGs abundances. The results indicated that WW-derived MPs, namely the MPs accumulated in sludge during the wastewater treatment process, exhibited significant inhibition on methane production by 22.8%-71.6%, while the AD-introduced MPs, being introduced in the sludge AD process, slightly increased the methane yield by 4.7%-17.1%. Meanwhile, MPs were responsible for promoting transmission of target ARGs, and polyethylene terephthalate MPs (PET-MPs) showed a greater promotion effect (0.0154-0.0936) than polyamide MPs (PA-MPs) (0.0013-0.0724). Compared to size, entry pathways and types played more vital roles on MPs influences. Investigation on mechanisms based on microbial community structure revealed characteristics (aging degree and types) of MPs determined the differences of AD performance and ARGs fates. WW-derived MPs with longer aging period and higher aging degree would release toxics and decrease the activities of microorganisms, resulting in the negative impact on AD performance. However, AD-introduced MPs with short aging period exhibited marginal impacts on AD performance. Furthermore, the co-occurrent network analysis suggested that the variations of potential host bacteria induced by MPs with different types and aging degree attributed to the dissemination of ARGs. Distinctively from most previous studies, the MPs with different sizes did not show remarkable effects on AD performance and ARGs fates. Our findings benefited the understanding of realistic environmental behavior and effect of MPs with different sources.

Aging and mitigation of microplastics during sewage sludge treatments: An overview

Wastewater treatment plants (WWTPs) receive large quantities of microplastics (MPs) from raw wastewater, but many MPs are trapped in the sludge. Land application of sludge is a significant source of MP pollution. Existing reviews have summarized the analysis methods of MPs in sludge and the effect of MPs on sludge treatments. However, MP aging and mitigation during sludge treatment processes are not fully reviewed. Treatment processes used to remove water, pathogenic microorganisms, and other pollutants in sewage sludge also cause surface changes and degradation in the sludge MPs, affecting the potential risk of MPs. This study integrates MP abundance and distribution in sludge and their aging and mitigation characteristics during sludge treatment processes. The abundance, composition, and distribution of sludge MPs vary significantly with WWTPs. Furthermore, MPs exhibit variable degrees of aging, including rough surfaces, enhanced adsorption potentials for pollutants, and increased leaching behavior. Various sludge treatment processes further intensify these aging characteristics. Some sludge treatments, such as hydrothermal treatment, have efficiently removed MPs from sewage sludge. It is crucial to understand the potential risk of MP aging in sludge and the degradation properties of the MP-derived products from MP degradation in-depth and develop novel MP mitigation strategies in sludge, such as combining hydrothermal treatment and biological processes.

Can low-temperature thermal hydrolysis mitigate the oxidative stress of polystyrene nanoplastics on anaerobic digestion?

The presence of micro/nanoplastics (MPs/NPs) in sewage sludge has sparked considerable apprehensions over their potential negative effects on anaerobic digestion (AD) performance. The occurrence of MPs/NPs can trigger oxidative stress on the anaerobic microbiome, leading to potential inhibition of the AD process. While the thermal hydrolysis process (THP) is an extensively utilized sludge pretreatment method for AD, its impact on stress induced by MPs/NPs during AD remains poorly understood. In this study, we assessed the impacts of low-temperature THP (90 °C, 90 min) on AD of sewage sludge in the presence of 150 μg/L of polystyrene nanoplastics (PsNPs) under different solid retention times (SRTs) of 20, 15, and 10 d. The presence of PsNPs resulted in a higher reactive oxygen species (ROS) production and a higher abundance of antibiotic resistance genes (ARGs). Additionally, their presence caused a significant inhibition of methane production by 28.2%, 29.3%, and 38.8% for SRTs of 20, 15, and 10 d, respectively. Introducing low-temperature THP prior to the AD could partially recover methane production by mitigating ROS-induced stress and curbing the propagation of ARGs during the AD process. These results shed light on the potential benefits of THP and further optimization opportunities in alleviating the adverse effects of MPs/NPs-induced stress during sewage sludge AD.

Effects of mesophilic and thermophilic anaerobic digestion of sewage sludge on different polymers: Perspectives on the potential of the treatment to degrade microplastics

Sewage sludge is produced during municipal wastewater treatment and can be further treated to be used for soil applications due to its high nutrient and carbon content. Anaerobic digestion is often used to manage sewage sludge. However, sewage sludge has a high load of microplastics that can be transferred to the soil, causing a burden to the environment. Some researchers suggest that anaerobic digestion could be used as a method to remove microplastics from sewage sludge, while others have shown the opposite. In this study, a variety of commodity polymers (LLDPE, HDPE, PP, PS, PET, uPVC, PA66 and SBR) are tested under mesophilic (35 °C) and thermophilic (55 °C) anaerobic digestion to evaluate their degradation after the process. As 1 mm thick sheets of polymers were used, in terms of diffusion they were considered to correspond to microplastics. Different characterization methods were used to access the visual, chemical, mechanical and thermal changes caused by anaerobic digestion. The results showed evidence of polymer degradation, for example, surface smoothening of LLDPE, HDPE and PP, embrittlement of PS and uPVC, hydrolysis of PET, plasticization of PA66, and surface cracking of SBR. However, although some changes in properties happened, anaerobic digestion could not comprehensively degrade the studied polymers. Therefore, this study suggests that anaerobic digestion of sewage sludge, at the conditions tested, is not able to be used as a method to eliminate microplastics from the sewage sludge before it is added to the soil.

Exposure to phagolysosomal simulated fluid altered the cytotoxicity of PET micro(nano)plastics to human lung epithelial cells

The occurrence of micro(nano)plastics into various environmental and biological settings influences their physicochemical and toxic behavior. Simulated body fluids are appropriate media for understanding the degradation, stability, and interaction with other substances of any material in the human body. When the particles enter the human body via inhalation, which is one of the avenues for micro(nano)plastics, they first come into contact with the lung lining fluid under neutral conditions and then are phagocytosed under acidic conditions to be removed. Therefore, it is important to examine the physicochemical transformation and toxicity characteristics after interaction with phagolysosomal simulant fluid (PSF). Here, we focused on exploring how the physicochemical differences (e.g. surface chemistry, elemental distribution, and surface charge) of micro(nano)plastics under pH 4.5 phagolysosome conditions impact cytotoxicity and the oxidative characteristics of lung epithelia cells. The cytotoxicity of lung epithelia cells to those treated with PSF and non-treated micro(nano)plastics was tested by various viability indicators including cell counting kit-8 (CCK-8), MTT, and LDH. Furthermore, the cytotoxicity background was examined through the oxidative processes (e.g. reactive oxygen species, antioxidant, superoxide dismutase (SOD), catalase, and reduced glutathione). The results showed that all tested surface physicochemical characteristics were significantly influenced by the phagolysosome conditions. The staged responses were observed with the treatment duration, and significant changes were calculated in carbonyl, carbon-nitrogen, and sulfonyl groups. Moreover, the negativity of the zeta potentials declined between exposure of 2-40 h and then increased at 80 h compared to control owing to the chemical functional groups and elemental distribution of the plastic particles. The tested viability indicators showed that the micro(nano)plastics treated with PSF were cytotoxic to the lung epithelia cells compared to non-treated micro(nano)plastics, and SOD was the dominant enzyme triggering cytotoxicity due to the particle degradation and instability.

Microfibers in anaerobic digestion: Effect of ozone pretreatment

Wastewater treatment plants receive significant microplastics, which are eventually discharged into the environment. Previous studies indicated that over 90% of microplastics, especially microfibers from laundry wastewater, are retained in primary sludge. The effect of microfibers from household laundry on anaerobic digestion has yet to be fully understood, which is the objective of the present study. The results in this study showed a positive correlation between methane production and the presence of microfibers. Compared to the control, the methane production increased by 2%, 27% and 43% with 20 mg/L, 100 mg/L and 1000 mg/L microfibers spiked into primary sludge, respectively. The present study suggests that microfibers at 20 mg/L insignificantly affected methane production in controlled anaerobic digestion. In contrast, ozone pretreatment of microfibers enhanced gas production by 12% in the same concentration level. Interestingly, ozone pretreatment at a higher concentration (100 mg/L-1000 mg/L) of microfibers did not affect methane production. SEM/EDX results imply that the ozone pretreatment has changed the surface characteristics of the microfibers, which provide more surface area for adsorption. The significant reduction of soluble phosphorus by 58% indicates that microfibers potentially act as a site for adsorption during anaerobic digestion. Overall, the presence of microfibers had a positive effect on anaerobic digestion. However, this work also indicated that the microfibers were not biodegraded during anaerobic digestion. Therefore, microfibers accumulate on biosolids, potentially affecting the final disposal of microfibers.

High-Value Oil-Water Separation Materials Prepared from Waste Polyethylene Terephthalate

As one of the most common forms of waste, waste PET is a serious pollutant in natural and human living environments. There is an urgent need to recycle PET. For this study, the complete degradation of PET was realized at a low temperature. A lipophilic hydrophobic membrane was formed on the surface of a stainless steel mesh (SSM) using a simple dip coating method, and an oil-water separation material was successfully prepared. After loading with degradation products, the surface roughness of SSM increased from 19.09 μm to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123°. The oil-water separation flux of the modified SSM was 9825 L/(m2·h), and the separation efficiency was 98.99%. The modified SSM had good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. The porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, not only solving the problem of white pollution but also reducing the dependence on non-renewable resources in the conventional methods used for the preparation of oil-water separation materials. This study provides new raw materials and methods for the industrial production of oil-water separation materials, which have important application prospects.

Synergistic effects of biochar derived from different sources on greenhouse gas emissions and microplastics mitigation during sewage sludge composting

This study aimed to investigate the effects of biochar derived from different sources (wheat straw, sawdust and pig manure) on greenhouse gas and microplastics (MPs) mitigation during sewage sludge composting. Compared to the control, all biochar significantly reduced the N2O by 28.91-41.23%, while having no apparent effect on CH4. Sawdust biochar and pig manure biochar significantly reduced the NH3 by 12.53-23.53%. Adding biochar decreased the global warming potential during composting, especially pig manure biochar (177.48 g/kg CO2-eq.). The concentration of MPs significantly increased in the control (43736.86 particles/kg) compared to the initial mixtures, while the addition of biochar promoted the oxidation and degradation of MPs (15896.06-23225.11 particles/kg), with sawdust biochar and manure biochar were more effective. Additionally, biochar significantly reduced the abundance of small-sized (10-100 μm) MPs compared to the control. Moreover, biochar might regulate specific microbes (e.g., Thermobifida, Bacillus and Ureibacillus) to mitigate greenhouse gas emissions and MPs degradation.

Differential effects of petroleum-based and bio-based microplastics on anaerobic digestion: A review

The number of plastics is increasing owing to the rapid development of the plastics industry. Microplastics (MPs) are formed during the use of both petroleum-based plastics and newly developed bio-based plastics. These MPs are inevitably released into the environment and are enriched in wastewater treatment plant sludge. Anaerobic digestion is a popular sludge stabilization method for wastewater treatment plants. Understanding the potential impacts of different MPs on anaerobic digestion is critical. This paper provides a comprehensive review of the mechanisms of petroleum-based MPs and bio-based MPs in anaerobic digestion methane production and compares their potential effects on biochemical pathways, key enzyme activities, and microbial communities. Finally, it identifies problems that must be solved in the future, proposes the focus of future research, and predicts the future development direction of the plastics industry.

A review on mechanistic understanding of microplastic pollution on the performance of anaerobic digestion

Anaerobic digestion (AD) has emerged as a promising technology for diverting the organic waste from the landfills along with the production of clean energy. AD is a microbial-driven biochemical process wherein the plethora of microbial communities participate in converting the putrescible organic matter into biogas. Nevertheless, the AD process is susceptible to the external environmental factors such as presence of physical (microplastics) and chemical (antibiotics, pesticides) pollutants. The microplastics (MPs) pollution has received recent attention due to the increasing plastic pollution in terrestrial ecosystems. This review was aimed for holistic assessment of impact of MPs pollution on AD process to develop efficient treatment technology. First, the possible pathways of MPs entry into the AD systems were critically evaluated. Further, the recent literature on the experimental studies pertaining to the impact of different types of MPs at different concentrations on the AD process was reviewed. In addition, several mechanisms such as direct exposure of MPs on the microbial cells, indirect impact of MPs through the leaching of toxic chemicals and reactive oxygen species (ROS) formation on AD process were elucidated. Besides, the risk possessed by the increase of antibiotic resistance genes (ARGs) after the AD process due to the MPs stress on microbial communities were discussed. Overall, this review deciphered the severity of MPs pollution on AD process at different levels.

Microplastics Derived from Food Packaging Waste-Their Origin and Health Risks

Plastics are commonly used for packaging in the food industry. The most popular thermoplastic materials that have found such applications are polyethylene (PE), polypropylene (PP), poly(ethylene terephthalate) (PET), and polystyrene (PS). Unfortunately, most plastic packaging is disposable. As a consequence, significant amounts of waste are generated, entering the environment, and undergoing degradation processes. They can occur under the influence of mechanical forces, temperature, light, chemical, and biological factors. These factors can present synergistic or antagonistic effects. As a result of their action, microplastics are formed, which can undergo further fragmentation and decomposition into small-molecule compounds. During the degradation process, various additives used at the plastics' processing stage can also be released. Both microplastics and additives can negatively affect human and animal health. Determination of the negative consequences of microplastics on the environment and health is not possible without knowing the course of degradation processes of packaging waste and their products. In this article, we present the sources of microplastics, the causes and places of their formation, the transport of such particles, the degradation of plastics most often used in the production of packaging for food storage, the factors affecting the said process, and its effects.