Recovery of Elemental Tellurium Nanoparticles by the Reduction of Tellurium Oxyanions in a Methanogenic Microbial Consortium

Achieving ultrafast and highly selective capture of radiotoxic tellurite ions on iron-based metal-organic frameworks through coordination bond-dominated conversion

Chemically durable and effective adsorbents for radiotoxic TeOx2- (TeIV and TeVI) anions remain in great demand for contamination remediation. Herein, a low-cost iron-based metal-organic framework (MIL-101(Fe)) was used as an adsorbent to capture TeOx2- anions from contaminated solution with ultrafast kinetics and record-high adsorption capacity of 645 mg g-1 for TeO32- and 337 mg g-1 for TeO42-, outperforming previously reported adsorbents. Extended X-ray absorption fine structure (EXAFS) and density functional theory (DFT) calculations confirmed that the capture of TeOx2- by MIL-101(Fe) was mediated by the unique C-O-Te and Fe-O-Te coordination bonds at corresponding optimal adsorption sites, which enabled the selective adsorption of TeOx2- from solution and further irreversible immobilization under the geological environment. Meanwhile, MIL-101(Fe) works steadily over a wide pH range of 4-10 and at high concentrations of competing ions, and it is stable under β-irradiation even at high dose of 200 kGy. Moreover, the MIL-101(Fe) membrane was fabricated to efficiently remove TeO32- ions from seawater for practical use, overcoming the secondary contamination and recovery problems in powder adsorption. Finally, the good sustainability of MIL-101(Fe) was evaluated from three perspectives of technology, environment, and society. Our strategy provides an alternative to traditional removal methods that should be attractive for Te contamination remediation.

In situ, synthesis of chitosan fabricated tellurium nanoparticles for improved antimicrobial and anticancer applications

The emergence of antibiotic resistance has had a severe impact on human health and economic burdens, drawing attention to the development of novel antimicrobial therapies. Polymer-metal composites have shown evidence of therapeutic applications by exerting antimicrobial effects and delivering these antimicrobials with biocompatibility. Therefore, this study prepared and characterized chitosan (CS)-fabricated tellurium nanoparticles (Te NPs) for enhanced antimicrobial, antioxidant, and cytotoxicity applications. The CS-Te NPs were spherical, polydisperse, and distributed within the CS matrix with an average size of 37.48 ± 14.56 nm, as confirmed by TEM analysis. CS-Te NPs exhibited positive zeta potential in neutral (pH 7.0: 7.90 ± 1.86 mV) and acidic environment. XRD analysis confirmed the crystalline nature of CS-Te NPs, and these nanoparticles exhibited good thermal and less porosity. A higher release of Te ions occurred from CS-Te NPs at an acidic pH. Further, CS-Te NPs displayed stronger antibacterial and antibiofilm activity against E. coli and S. enterica. Furthermore, CS-Te NPs exhibited significant free radical scavenging activity against ABTS and DPPH free radicals. Moreover, these nanoparticles demonstrated cytotoxicity against cancerous cells (A549 and PC3 cells) when compared to normal cells (NIH3T3 cells). Therefore, this study suggests that CS-Te NPs could serve as a substantial therapeutic agent.

Biosynthesis of gallic acid fabricated tellurium nanoparticles (GA-Te NPs) for enhanced antibacterial, antioxidant, and cytotoxicity applications

The development of antibiotic resistance and the onset of diverse forms of cancer necessitate the utilization of innovative multifunctional biocompatible materials. The synthesis of metal and metalloid nanoparticles through eco-friendly means demonstrates promising potential in therapeutic and diagnostic domains. Among these materials, Tellurium (Te) exhibits exceptional characteristics and finds application in numerous fields; nevertheless, its usage in biological applications has been somewhat limited, primarily due to its inherent toxicity. Furthermore, nanomaterials developed from Te have not garnered adequate research attention. Conversely, nanomaterials fashioned using biomolecules augment their biological efficacy and applicability. Therefore, the present work focuses on synthesizing the tellurium nanoparticles (Te NPs) using the antioxidant molecule gallic acid (GA) and evaluating their biological activity and toxicity for the first time. The study evidenced that GA-Te NPs are spherical and monodispersed, with an average size of 19.74 ± 5.3 nm. XRD analysis confirmed a hexagonal crystalline structure for GA-Te NPs, and FTIR analysis evidenced the capping of GA on Te NPs. GA-Te NPs (MIC: 1.56 μg/mL) strongly reduce the growth and biofilm formation of S. aureus, E. coli, and S. enterica. Additionally, GA-Te NPs at a concentration of 50 μg/mL cause a significant level of toxicity in BT474 breast cancer cells but not in NIH3T3 cells. Unexpectedly, GA-Te NPs at concentrations <250 μg/mL do not cause hemolysis in red blood cells (RBC) Besides, the way of utilizing the lower concentrations of therapeutics could result in ecological safety. Therefore, the study concludes that GA-Te NPs could be used as potential multifunctional agents.

The cryptic step in the biogeochemical tellurium (Te) cycle: Indirect elementary Te oxidation mediated by manganese-oxidizing bacteria Bacillus sp. FF-1

Tellurium (Te) is a rare element within the chalcogen group, and its biogeochemical cycle has been studied extensively. Tellurite (Te(IV)) is the most soluble Te species and is highly toxic to organisms. Chemical or biological Te(IV) reduction to elemental tellurium (Te0) is generally considered an effective detoxification route for Te(IV)-containing wastewater. This study unveils a previously unnoticed Te0 oxidation process mediated by the manganese-oxidizing bacterium Bacillus sp. FF-1. This bacterium, which exhibits both Mn(II)-oxidizing and Te(IV)-reducing abilities, can produce manganese oxides (BioMnOx) and Te0 (BioTe0) when exposed to Mn(II) and Te(IV), respectively. When 5 mM Mn(II) was added after incubating 0.1 mM or 1 mM Te(IV) with strain FF-1 for 16 h, BioTe0 was certainly re-oxidized to Te(IV) by BioMnOx. Chemogenic and exogenous biogenic Te0 can also be oxidized by BioMnOx, although at different rates. This study highlights a new transformation process of tellurium species mediated by manganese-oxidizing bacteria, revealing that the environmental fate and ecological risks of Te0 need to be re-evaluated.

Microbial mechanisms to transform the super-trace element tellurium: a systematic review and discussion of nanoparticulate phases

Tellurium is a super-trace metalloid on Earth. Owing to its excellent physical and chemical properties, it is used in industries such as metallurgy and manufacturing, particularly of semiconductors and - more recently - solar panels. As the global demand for tellurium rises, environmental issues surrounding tellurium have recently aroused concern due to its high toxicity. The amount of tellurium released to the environment is increasing, and microorganisms play an important role in the biogeochemical cycling of environmental tellurium. This review focuses on novel developments on tellurium transformations driven by microbes and includes the following sections: (1) history and applications of tellurium; (2) toxicity of tellurium; (3) microbial detoxification mechanisms against soluble tellurium anions including uptake, efflux and methods of reduction, and reduced ability to cope with oxidation stress or repair damaged DNA; and (4) the characteristics and applications of tellurium nanoparticles (TeNPs) produced by microbes. This review raises the awareness of microorganisms in tellurium biogeochemical cycling and the growing applications for microbial tellurium nanoparticles.

Dopamine modified layered double hydroxide membranes based on nanofibril architectures: Toward superior tellurium separation properties for water treatment

Two-dimensional (2D) membrane materials are widely employed for the accurate sieving of ionic contaminants and are of great importance for water reuse. However, 2D membrane materials often suffer from uneven thickness and surface defects, which severely limit their application prospects. Herein, a continuous 2D membrane (LCUM/D) was prepared using cellulose nanofibrils (CNFs) as the support backbone for the assembled layered double hydroxides (LDHs) and dopamine (DA) as the adhesive. The results demonstrated that LDHs could be uniformly distributed in the network structure of CNFs, and the defects on the membrane surface could be effectively compensated by DA. Simultaneously, the continuous LCUM/D showed excellent rejection (97.18%) and selectivity of ionic contaminants tellurium. Dopamine not only compensated for the surface defects of the 2D membrane and enhanced the rejection of tellurium, but also caused no significant loss of water permeance. Moreover, the LCUM/D exhibited stability, which facilitated its long-term application. In addition, the improved hydrophilicity allowed LCUM/D satisfactory anti-fouling properties. This study provides new dimensional insights into the fabrication of continuous 2D membranes for the removal of ionic contaminant and enhances their application prospects in wastewater treatment.

Biosynthesis of Novel Tellurium Nanorods by Gayadomonas sp. TNPM15 Isolated from Mangrove Sediments and Assessment of Their Impact on Spore Germination and Ultrastructure of Phytopathogenic Fungi

The biosynthesis of nanoparticles using green technology is emerging as a cost-efficient, eco-friendly and risk-free strategy in nanotechnology. Recently, tellurium nanoparticles (TeNPs) have attracted growing attention due to their unique properties in biomedicine, electronics, and other industrial applications. The current investigation addresses the green synthesis of TeNPs using a newly isolated mangrove-associated bacterium, Gayadomonas sp. TNPM15, and their impact on the phytopathogenic fungi Fusarium oxysporum and Alternaria alternata. The biogenic TeNPs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Raman spectroscopy and Fourier transform infrared (FTIR). The results of TEM revealed the intracellular biosynthesis of rod-shaped nanostructures with a diameter range from 15 to 23 nm and different lengths reaching up to 243 nm. Furthermore, the successful formation of tellurium nanorods was verified by SEM-EDX, and the XRD pattern revealed their crystallinity. In addition, the FTIR spectrum provided evidence for the presence of proteinaceous capping agents. The bioinspired TeNPs exhibited obvious inhibitory effect on the spores of both investigated phytopathogens accomplished with prominent ultrastructure alternations, as evidenced by TEM observations. The biogenic TeNPs impeded spore germination of F. oxysporum and A. alternata completely at 48.1 and 27.6 µg/mL, respectively. Furthermore, an increase in DNA and protein leakage was observed upon exposure of fungal spores to the biogenic TeNPs, indicating the disruption of membrane permeability and integrity. Besides their potent influence on fungal spores, the biogenic TeNPs demonstrated remarkable inhibitory effects on the production of various plant cell wall-degrading enzymes. Moreover, the cytotoxicity investigations revealed the biocompatibility of the as-prepared biogenic TeNPs and their low toxicity against the human skin fibroblast (HSF) cell line. The biogenic TeNPs showed no significant cytotoxic effect towards HSF cells at concentrations up to 80 μg/mL, with a half-maximal inhibitory concentration (IC50) value of 125 μg/mL. The present work spotlights the antifungal potential of the biogenic TeNPs produced by marine bacterium against phytopathogenic fungi as a promising candidate to combat fungal infections.

Simultaneous bioremediation of phenol and tellurite by Lysinibacillus sp. EBL303 and characterization of biosynthesized Te nanoparticles

Aromatic compounds and metalloid oxyanions are abundant in the environment due to natural resources and industrial wastes. The high toxicity of phenol and tellurite poses a significant threat to all forms of life. A halotolerant bacterium was isolated and identified as Lysinibacillus sp. EBL303. The remediation analysis shows that 500 mg/L phenol and 0.5 mM tellurite can be remediated entirely in separate cultures within 74 and 56 h, respectively. In addition, co-remediation of pollutants resulted in the same phenol degradation and 27% less tellurite reduction within 98 h. Since phenol and tellurite exhibited inhibitory behavior, their removal kinetics fitted well with the first-order model. In the characterization of biosynthesized tellurium nanoparticles (TeNPs), transmission electron microscopy, dynamic light scattering, FE-SEM, and dispersive X-ray (EDX) showed that the separated intracellular TeNPs were spherical and consisted of only tellurium with 22-148 nm in size. Additionally, investigations using X-ray diffraction and Fourier-transform infrared spectroscopy revealed proteins and lipids covering the surface of these amorphous TeNPs. Remarkably, this study is the first report to demonstrate the simultaneous bioremediation of phenol and tellurite and the biosynthesis of TeNPs, indicating the potential of Lysinibacillus sp. EBL303 in this matter, which can be applied to environmental remediation and the nanotechnology industry.

Evidence and Mechanisms of Selenate Reduction to Extracellular Elemental Selenium Nanoparticles on the Biocathode

Intracellular selenium nanoparticles (SeNPs) production is a roadblock to the recovery of selenium from biological water treatment processes because it is energy intensive to break microbial cells and then separate SeNPs. This study provided evidence of significantly more extracellular SeNP production on the biocathode (97-99%) compared to the conventional reactors (1-90%) using transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy. The cathodic microbial community analysis showed that relative abundance of Azospira oryzae, Desulfovibrio, Stenotrophomonas, and Rhodocyclaceae was <1% in the inoculum but enriched to 10-21% for each group when the bioelectrochemical reactor reached a steady state. These four groups of microorganisms simultaneously produce intracellular and extracellular SeNPs in conventional biofilm reactors per literature review but prefer to produce extracellular SeNPs on the cathode. This observation may be explained by the cellular energetics: by producing extracellular SeNPs on the biocathode, microbes do not need to transfer selenate and the electrons from the cathode into the cells, thereby saving energy. Extracellular SeNP production on the biocathode is feasible since we found high concentrations of C-type cytochrome, which is well known for its ability to transfer electrons from electrodes to microbial cells and reduce selenate to SeNPs on the cell membrane.

Enhancing tellurite and selenite bioconversions by overexpressing a methyltransferase from Aromatoleum sp. CIB

Pollution by metalloids, e.g., tellurite and selenite, is of serious environmental concern and, therefore, there is an increasing interest in searching for ecologically friendly solutions for their elimination. Some microorganisms are able to reduce toxic tellurite/selenite into less toxic elemental tellurium (Te) and selenium (Se). Here, we describe the use of the environmentally relevant β-proteobacterium Aromatoleum sp. CIB as a platform for tellurite elimination. Aromatoleum sp. CIB was shown to tolerate 0.2 and 0.5 mM tellurite at aerobic and anaerobic conditions, respectively. Furthermore, the CIB strain was able to reduce tellurite into elemental Te producing rod-shaped Te nanoparticles (TeNPs) of around 200 nm length. A search in the genome of Aromatoleum sp. CIB revealed the presence of a gene, AzCIB_0135, which encodes a new methyltransferase that methylates tellurite and also selenite. AzCIB_0135 orthologs are widely distributed in bacterial genomes. The overexpression of the AzCIB_0135 gene both in Escherichia coli and Aromatoleum sp. CIB speeds up tellurite and selenite removal, and it enhances the production of rod-shaped TeNPs and spherical Se nanoparticles (SeNPs), respectively. Thus, the overexpression of a methylase becomes a new genetic strategy to optimize bacterial catalysts for tellurite/selenite bioremediation and for the programmed biosynthesis of metallic nanoparticles of biotechnological interest.

Insights into the recent advances in nano-bioremediation of pesticides from the contaminated soil

In the present scenario, the uncontrolled and irrational use of pesticides is affecting the environment, agriculture and livelihood worldwide. The excessive application of pesticides for better production of crops and to maintain sufficient food production is leading to cause many serious environmental issues such as soil pollution, water pollution and also affecting the food chain. The efficient management of pesticide use and remediation of pesticide-contaminated soil is one of the most significant challenges to overcome. The efficiency of the current methods of biodegradation of pesticides using different microbes and enzymes depends on the various physical and chemical conditions of the soil and they have certain limitations. Hence, a novel strategy is the need of the hour to safeguard the ecosystem from the serious environmental hazard. In recent years, the application of nanomaterials has drawn attention in many areas due to their unique properties of small size and increased surface area. Nanotechnology is considered to be a promising and effective technology in various bioremediation processes and provides many significant benefits for improving the environmental technologies using nanomaterials with efficient performance. The present article focuses on and discusses the role, application and importance of nano-bioremediation of pesticides and toxic pollutants to explore the potential of nanomaterials in the bioremediation of hazardous compounds from the environment.

Electron shuttles enhanced the removal of antibiotics and antibiotic resistance genes in anaerobic systems: A review

The environmental and epidemiological problems caused by antibiotics and antibiotic resistance genes have attracted a lot of attention. The use of electron shuttles based on enhanced extracellular electron transfer for anaerobic biological treatment to remove widespread antibiotics and antibiotic resistance genes efficiently from wastewater or organic solid waste is a promising technology. This paper reviewed the development of electron shuttles, described the mechanism of action of different electron shuttles and the application of enhanced anaerobic biotreatment with electron shuttles for the removal of antibiotics and related genes. Finally, we discussed the current issues and possible future directions of electron shuttle technology.

Nanotechnology in the Restoration of Polluted Soil

The advancements in nanoparticles (NPs) may be lighting the sustainable and eco-friendly path to accelerate the removal of toxic compounds from contaminated soils. Many efforts have been made to increase the efficiency of phytoremediation, such as the inclusion of chemical additives, the application of rhizobacteria, genetic engineering, etc. In this context, the integration of nanotechnology with bioremediation has introduced new dimensions for revamping the remediation methods. Hence, advanced remediation approaches combine nanotechnological and biological remediation methods in which the nanoscale process regulation supports the adsorption and deterioration of pollutants. Nanoparticles absorb/adsorb a large variety of contaminants and also catalyze reactions by lowering the energy required to break them down, owing to their unique surface properties. As a result, this remediation process reduces the accumulation of pollutants while limiting their spread from one medium to another. Therefore, this review article deals with all possibilities for the application of NPs for the remediation of contaminated soils and associated environmental concerns.

Synergistic bioreduction of Te(Ⅳ) using S(0) as electron donor

This study for the first time bioreduced Te(IV) using elemental sulfur (S⁰) as electron donor, achieving 91.17%±0.8% conversion with reaction rate of 0.77 ± 0.01 mg/L/h in a 60-day cultivation. Characterization using X-ray photoelectron spectroscopy and X-ray power diffraction analyses confirmed that most removed Te(IV) was reduced to elemental Te(0) deposits, while ion chromatogram analysis showed that most S(0) was oxidized to sulfite and sulfate. High-throughput 16S rRNA gene sequencing indicated that the Te(IV) reduction coupled to S(0) oxidation was mediated synergistically by a microbial consortia with S(0)-oxidizing bacteria (Thiobacillus) to generate volatile fatty acids as metabolites and Te(IV)-reducing bacteria (Rhodobacter) to consume formed volatile fatty acids to yield Te(0). The synergy between these two strains presents a novel bioremediation consortium to efficiently treat Te(IV) wastewaters.

UV-Induced Redox Conversion of Tellurite by Biacetyl

Tellurium (Te) is a rare element of great value, but it exists mainly in the toxic form of tellurite (Te^IV) in water. Effective approaches that are able to reduce the toxicity and recover Te from contaminated water are highly needed. Here, we developed a simple but effective way to reduce toxic Te^IV to widely applicable elemental Te⁰. With the combination of ultraviolet (UV) and biacetyl (BD), the oxidation state of Te could be feasibly changed from IV to 0 or VI. The consumption of dissolved oxygen (DO) was a key factor in the redox conversion of Te^IV. Under UV irradiation, BD was first cleaved to acetyl radicals, which could then combine with water molecules to form more reductive diol radicals or combine with DO to form strongly oxidative peroxide radicals. Even without deoxygenation, the UV/BD system could rapidly change from being oxidative to being reductive because of the fast depletion of DO. Owing to the high quantum yield of the acetyl radical, the reduction efficiency of the UV/BD system was about 1 order of magnitude higher than that of UV/sulfite and was more efficient than the commonly used biological methods. This work provides a proof of concept for the reduction of tellurite, which could have relevant implications for water treatment and resource recovery applications.

Development of biogenic bimetallic Pd/Fe nanoparticle-impregnated aerobic microbial granules with potential for dye removal

The objective of this study was to develop bimetallic core-shell Pd/Fe nanoparticles on the surface of aerobic microbial granules (Bio-Pd/Fe) and to evaluate their dye removal potential using a representative dye, methyl orange (MO). The aerobic microbial granules (1.5 ± 0.32 mm) were grown for 70 days in a 3-L glass sequencing batch reactor (SBR) with a 12-h cycle time. The Bio-Pd/Fe formation was catalyzed by the Bio-H₂ gas produced by the granules. The developed Bio-Pd/Fe was further used for MO removal from aqueous solutions, and the reaction parameters were optimized by response surface methodology (RSM). The XRD, SEM, EDAX, elemental mapping, and XPS studies confirmed the formation of Bio-Pd/Fe. Under the optimized removal conditions, 99.33% MO could be removed by Bio-Pd/Fe, whereas removal by Bio-Pd, Bio-Fe, aerobic microbial granules, and heat-killed granules were found to be quite low (68.91 ± 0.2%, 76.8 ± 0.3%, 19.8 ± 0.6%, and 6.59 ± 0.2%, respectively). The mechanism of removal was investigated by UV-visible spectroscopy, redox potential analysis, HR-LCMS analyses of the solution phase, and XRD and XPS analyses of the solid sorbent. The degradation products of MO exhibited m/z values corresponding to 292, 212, and 160 m/z. The remnant toxicity of the intermediate degradation products was analysed using freshwater algae, Scenedesmus sp. And Allium cepa, as indicator organisms. These assays suggested that after the treatment with Bio-Pd/Fe, MO was transformed to a lesser toxic form.

Characterisation of selenium and tellurium nanoparticles produced by Aureobasidium pullulans using a multi-method approach

Aureobasidium pullulans was grown in liquid culture media amended with selenite and tellurite and selenium (Se) and tellurium (Te) nanoparticles (NPs) were recovered after 30 d incubation. A separation method was applied to recover and characterise Se and Te NPs by asymmetric flow field flow fractionation (AF4) with online coupling to multi-angle light scattering (MALS), ultraviolet visible spectroscopy (UV-Vis), and inductively coupled plasma mass spectrometry (ICP-MS) detectors. Additional characterisation data was obtained from transmission electron microscopy (TEM), and dynamic light scattering (DLS). Solutions of 0.2% Novachem surfactant and 10 mM phosphate buffer were compared as mobile phases to investigate optimal AF4 separation and particle recovery using Se-NP as a model sample. 88% recovery was reported for 0.2% Novachem solution, compared with 50% recovery for phosphate buffer. Different crossflow (C_flow) rates were compared to further investigate optimum separation, with recoveries of 88% and 30% for Se-NPs, and 90% and 29% for Te-NPs for 3.5 mL min^-1 and 2.5 mL min^-1 respectively. Zeta-potential (ZP) data suggested higher stability for NP elution in Novachem solution, with increased stability attributed to minimised NP-membrane interaction due to PEGylation. Detection with MALS showed monodisperse Se-NPs (45-90 nm) and polydisperse Te-NPs (5-65 nm).Single particle ICP-MS showed mean particle diameters of 49.7 ± 2.7 nm, and 135 ± 4.3 nm, and limit of size detection (LOSD) of 20 nm and 45 nm for Se-NPs and Te-NPs respectively. TEM images of Se-NPs and Te-NPs displayed a spherical morphology, with the Te-NPs showing a clustered arrangement, which suggested electrostatic attraction amongst neighbouring particles. Particle hydrodynamic diameters (d_H) measured with dynamic light scattering (DLS) further suggested monodisperse Se-NPs and polydisperse Te-NPs distributions, showing good agreement with AF4-MALS for Se-NPs, but suggests that the R_g obtained from AF4-MALS for Te-NP was unreliable. The results demonstrate a complementary application of asymmetric flow field-flow fractionation (AF4), ICP-MS, light scattering, UV-Vis detection, and microscopic techniques to characterise biogenic Se and Te NPs.

Acceleration mechanism of bioavailable Fe(Ⅲ) on Te(IV) bioreduction of Shewanella oneidensis MR-1: Promotion of electron generation, electron transfer and energy level

The release of highly toxic tellurite into the aquatic environment poses significant environmental risks. The acceleration mechanism and tellurium nanorods (TeNPs) characteristics with bioavailable ferric citrate (Fe(III)) were investigated in the tellurite (Te(IV)) bioreduction. Experiments showed that 5 mM Fe(III) increased the Te(IV) bioreduction rate from 0 to 12.40 mg/(L·h). Cyclic voltammetry, electrochemical impedance spectroscopy and Tafel were used to investigate electron transfer during Te(IV) bioreduction. NADH production (electron production) was significantly enhanced to 138% by Fe(III). Meanwhile Fe(III) stimulated the increase of cytochrome c, resulting in increased electron transport system activity. In addition, Fe(III) facilitated the secretion of extracellular polymeric substances (EPS) and reduced cell membrane permeability, thus reducing the toxicity of Te(IV) to cells. The increase of ATP provided energy for the metabolic process of Te(IV) bioreduction, playing an active role in cell activity. Based on the above analysis, the acceleration mechanism of Fe(III) on Te(IV) bioreduction was proposed from the aspects of electron generation, electron transfer and energy level. Zeta potential and FT-IR spectra indicated that the stability of TeNPs contributed to the covered EPS. This study provides further understanding the acceleration mechanism of Te(IV) bioreduction and promising strategy for improving the stability of TeNPs.

Green Synthesis of Selenium and Tellurium Nanoparticles: Current Trends, Biological Properties and Biomedical Applications

The synthesis and assembly of nanoparticles using green technology has been an excellent option in nanotechnology because they are easy to implement, cost-efficient, eco-friendly, risk-free, and amenable to scaling up. They also do not require sophisticated equipment nor well-trained professionals. Bionanotechnology involves various biological systems as suitable nanofactories, including biomolecules, bacteria, fungi, yeasts, and plants. Biologically inspired nanomaterial fabrication approaches have shown great potential to interconnect microbial or plant extract biotechnology and nanotechnology. The present article extensively reviews the eco-friendly production of metalloid nanoparticles, namely made of selenium (SeNPs) and tellurium (TeNPs), using various microorganisms, such as bacteria and fungi, and plants' extracts. It also discusses the methodologies followed by materials scientists and highlights the impact of the experimental sets on the outcomes and shed light on the underlying mechanisms. Moreover, it features the unique properties displayed by these biogenic nanoparticles for a large range of emerging applications in medicine, agriculture, bioengineering, and bioremediation.

LC-ICP-OES method for antimony speciation analysis in liquid samples

A method for the analysis of different species of antimony (Sb) that couples liquid chromatography with an inductively coupled plasma-optical emission spectrometry (LC-ICP-OES) system is presented. The method is simple and reliable to separate and quantify directly and simultaneously Sb(III) and Sb(V) in aqueous samples. The calibration curves showed high linearity at the three wavelengths tested. The limits of detection ranged from 24.9 to 32.3 μg/L for Sb(III) and from 36.2 to 46.0 μg/L for Sb(V), at the three wavelengths evaluated. The limit of detection for this method varied depending on the wavelength used. The lowest limit of quantification for Sb(V) (49.9 μg/L) and Sb(III) (80.7 μg/L) was obtained at a wavelength of 217.582 nm. The method sensitivity for Sb(V) was higher compared to Sb(III) at all the wavelengths considered. Samples containing different concentrations of Sb(III) and Sb(V) in three different matrices, i.e., water, basal culture medium, and anaerobic sludge plus basal medium, were analyzed. The coefficients of variation were low and ranged from 0.1 to 5.0 depending on the sample matrix. Recoveries of Sb(III) and Sb(V) were higher than 90% independently of the matrix analyzed and the wavelength used in the analysis.

Extreme Environments and High-Level Bacterial Tellurite Resistance

Bacteria have long been known to possess resistance to the highly toxic oxyanion tellurite, most commonly though reduction to elemental tellurium. However, the majority of research has focused on the impact of this compound on microbes, namely E. coli, which have a very low level of resistance. Very little has been done regarding bacteria on the other end of the spectrum, with three to four orders of magnitude greater resistance than E. coli. With more focus on ecologically-friendly methods of pollutant removal, the use of bacteria for tellurite remediation, and possibly recovery, further highlights the importance of better understanding the effect on microbes, and approaches for resistance/reduction. The goal of this review is to compile current research on bacterial tellurite resistance, with a focus on high-level resistance by bacteria inhabiting extreme environments.

Formation of nanoscale Te0 and its effect on TeO32- reduction in CH4-based membrane biofilm reactor

Formation and recovery of elemental tellurium (Te⁰) from wastewaters are required by increasing demands and scarce resources. Membrane biofilm reactor (MBfR) using gaseous electron donor has been reported as a low-cost and benign technique to reduce and recover metal (loids). In this study, we demonstrate the feasibility of nanoscale Te⁰ formation by tellurite (TeO₃^2-) reduction in a CH₄-based MBfR. Biogenic Te⁰ intensively attached on cell surface, within diameters ranging from 10 nm to 30 nm and the hexagonal nanostructure. Along with the Te⁰ formation, the TeO₃^2- reduction was inhibited. After flushing, biofilm resumed the TeO₃^2- reduction ability, suggesting that the formed nanoscale Te⁰ might inhibit the reduction by hindering substrate transfer of TeO₃^2- to microbes. The 16S rRNA gene amplicon sequencing revealed that Thermomonas and Hyphomicrobium were possibly responsible for TeO₃^2- reduction since they increased consecutively along with the experiment operation. The PICRUSt (Phylogenetic Investigation of Communities by Reconstruction of Unobserved States) analysis showed that the sulfite reductases were positively correlated with the TeO₃^2- flux, indicating they were potential enzymes involved in reduction process. This study confirms the capability of CH₄-based MBfR in tellurium reduction and formation, and provides more techniques for resources recovery and recycles.

Cerium dioxide (CeO2) nanoparticles decrease arsenite (As(III)) cytotoxicity to 16HBE14o- human bronchial epithelial cells

The production and application of engineered nanoparticles (NPs) are increasing in demand with the rapid development of nanotechnology. However, there are concerns that some of these novel materials could lead to emerging environmental and health problems. Some NPs are able to facilitate the transport of contaminants into cells/organisms via a "Trojan Horse" effect which enhances the toxicity of the adsorbed materials. In this work, we evaluated the toxicity of arsenite (As(III)) adsorbed onto cerium dioxide (CeO2) NPs to human bronchial epithelial cells (16HBE14o-) using the xCELLigence real time cell analyzing system (RTCA). Application of 0.5 mg/L As(III) resulted in 81.3% reduction of cell index (CI, an RTCA measure of cell toxicity) over 48 h when compared to control cells exposed to medium lacking As(III). However, when the cells were exposed to 0.5 mg/L As(III) in the presence of CeO2 NPs (250 mg/L), the CI was only reduced by 12.9% compared to the control. The CeO2 NPs had a high capacity for As(III) adsorption (20.2 mg/g CeO2) in the bioassay medium, effectively reducing dissolved As(III) in the aqueous solution and resulting in reduced toxicity. Transmission electron microscopy was used to study the transport of CeO2 NPs into 16HBE14o- cells. NP uptake via engulfment was observed and the internalized NPs accumulated in vesicles. The results demonstrate that dissolved As(III) in the aqueous solution was the decisive factor controlling As(III) toxicity of 16HBE14o- cells, and that CeO2 NPs effectively reduced available As(III) through adsorption. These data emphasize the evaluation of mixtures when assaying toxicity.

Reduction of platinum (IV) ions to elemental platinum nanoparticles by anaerobic sludge

BACKGROUND

The future supply of platinum group metals (PGM) is at risk because of their scarcity combined with a high demand. Thus recovery of platinum (Pt) from waste is an option worthy of study to help alleviate future shortages. This research explored the microbial reduction of platinum (Pt). The ability of anaerobic granular sludge to reduce Pt(IV) ions under different physiological conditions was studied.

RESULTS

X-Ray diffraction (XRD) and transmission electron microscope (TEM) analyses demonstrated the capacity of the microbial mixed culture to reduce Pt(IV) to Pt(0) nanoparticles, which were deposited on the cell-surface and in the periplasmic space. Ethanol supported the biologically catalyzed Pt(IV) reduction, meanwhile other electron donors; hydrogen (H2) and formate, promoted the chemical reduction of Pt(IV) with some additional biological stimulation in the case of H2. A hypothesis is proposed in which H2 formed from the acetogenesis of ethanol is implicated in subsequent abiotic reduction of Pt(IV) indicating an integrated bio-chemical process. Endogenous controls also resulted in slow Pt(IV) removal from aqueous solution. Selected redox mediators, exemplified by riboflavin, enhanced the Pt(IV) reduction rate.

CONCLUSION

This study reported for the first time the ability of an anaerobic granular sludge to reduce Pt(IV) to elemental Pt(0) nanoparticles.

A novel strategy to evaluate the degradation of quantum dots: identification and quantification of CdTe quantum dots and corresponding ionic species by CZE-ICP-MS

In view of the significance and urgency of the speciation analysis of quantum dots (QDs) and their degradation products for clarifying their degradation rules and toxicity mechanisms, a method for the identification and quantification of CdTe QDs and corresponding ionic species in complex matrices was developed using capillary zone electrophoresis (CZE) coupled to inductively coupled plasma-mass spectrometry (ICP-MS). The quality assessment of commercial CdTe QDs and serum pharmacokinetics of synthesized CdTe QDs in rats were successfully undertaken using the developed CZE-ICP-MS method.

Formation of Se(0), Te(0), and Se(0)-Te(0) nanostructures during simultaneous bioreduction of selenite and tellurite in a UASB reactor

Simultaneous removal of selenite and tellurite from synthetic wastewater was achieved through microbial reduction in a lab-scale upflow anaerobic sludge blanket reactor operated with 12 h hydraulic retention time at 30 °C and pH 7 for 120 days. Lactate was supplied as electron donor at an organic loading rate of 528 or 880 mg COD L^-1 day^-1. The reactor was initially fed with a synthetic influent containing 0.05 mM selenite and tellurite each (phase I, day 1-60) and subsequently with 0.1 mM selenite and tellurite each (phase II, day 61-120). At the end of phase I, selenite and tellurite removal efficiencies were 93 and 96%, respectively. The removal percentage dropped to 87 and 81% for selenite and tellurite, respectively, at the beginning of phase II because of the increased influent concentrations. The removal efficiencies of both selenite and tellurite were gradually restored within 20 days and stabilized at ≥ 97% towards the end of the experiment. Powder X-ray diffraction and Raman spectroscopy confirmed the formation of biogenic Se(0), Te(0), and Se(0)-Te(0) nanostructures. Scanning transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy showed aggregates comprising of Se(0), Te(0), and Se-Te nanostructures embedded in a layer of extracellular polymeric substances (EPS). Infrared spectroscopy confirmed the presence of chemical signatures of the EPS which capped the nanoparticle aggregates that had been formed and immobilized in the granular sludge. This study suggests a model for technologies for remediation of effluents containing Se and Te oxyanions coupled with biorecovery of bimetal(loid) nanostructures.

Leaching of cadmium and tellurium from cadmium telluride (CdTe) thin-film solar panels under simulated landfill conditions

A crushed non-encapsulated CdTe thin-film solar cell was subjected to two standardized batch leaching tests (i.e., Toxicity Characteristic Leaching Procedure (TCLP) and California Waste Extraction Test (WET)) and to a continuous-flow column test to assess cadmium (Cd) and tellurium (Te) dissolution under conditions simulating the acidic- and the methanogenic phases of municipal solid waste landfills. Low levels of Cd and Te were solubilized in both batch leaching tests (<8.2% and <3.6% of added Cd and Te, respectively). On the other hand, over the course of 30days, 73% of the Cd and 21% of the Te were released to the synthetic leachate of a continuous-flow column simulating the acidic landfill phase. The dissolved Cd concentration was 3.24-fold higher than the TCLP limit (1mgL^-1), and 650-fold higher than the maximum contaminant level established by the US-EPA for this metal in drinking water (0.005mgL^-1). In contrast, the release of Cd and Te to the effluent of the continuous-flow column simulating the methanogenic phase of a landfill was negligible. The remarkable difference in the leaching behavior of CdTe in the columns is related to different aqueous pH and redox conditions promoted by the microbial communities in the columns, and is in agreement with thermodynamic predictions.

Tellurium Distribution and Speciation in Contaminated Soils from Abandoned Mine Tailings: Comparison with Selenium

The distribution and chemical species of tellurium (Te) in contaminated soil were determined by a combination of microfocused X-ray fluorescence (μ-XRF), X-ray diffraction (μ-XRD), and X-ray absorption fine structure (μ-XAFS) techniques. Results showed that Te was present as a mixture of Te(VI) and Te(IV) species, while selenium (Se) was predominantly present in the form of Se(IV) in the soil contaminated by abandoned mine tailings. In the contaminated soil, Fe(III) hydroxides were the host phases for Se(IV), Te(IV), and Te(VI), but Te(IV) could be also retained by illite. The difference in speciation and solubility of Se and Te in soil can result from different structures of surface complexes for Se and Te onto Fe(III) hydroxides. Furthermore, our results suggest that the retention of Te(IV) in soil could be relatively weaker than that of Te(VI) due to structural incorporation of Te(VI) into Fe(III) hydroxides. These findings are of geochemical and environmental significance for better understanding the solubility, mobility, and bioavailability of Te in the surface environment. To the best of our knowledge, this is the first study reporting the speciation and host phases of Te in field soil by the μ-XRF-XRD-XAFS techniques.

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

Continuous removal of tellurite (TeO₃^2-) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30°C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6g CODL^-1d^-1. After establishing efficient and stable COD removal, the reactor was fed with 10mg TeO₃^2-L^-1 for 42 d before increasing the influent concentration to 20mg TeO₃^2-L^-1. Tellurite removal (98 and 92%, respectively, from 10 and 20mg TeL^-1) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

Continuous reduction of tellurite to recoverable tellurium nanoparticles using an upflow anaerobic sludge bed (UASB) reactor

According to the U.S. Department of Energy and the European Union, tellurium is a critical element needed for energy and defense technology. Thus methods are needed to recover tellurium from waste streams. The objectives of this study was to determine the feasibility of utilizing upflow anaerobic sludge bed (UASB) reactors to convert toxic tellurite (Te^IV) oxyanions to non-toxic insoluble elemental tellurium (Te⁰) nanoparticles (NP) that are amendable to separation from aqueous effluents. The reactors were supplied with ethanol as the electron donating substrate to promote the biological reduction of Te^IV. One reactor was additionally amended with the redox mediating flavonoid compound, riboflavin (RF), with the goal of enhancing the bioreduction of Te^IV. Its performance was compared to a control reactor lacking RF. The continuous formation of Te⁰ NPs using the UASB reactors was found to be feasible and remarkably improved by the addition of RF. The presence of this flavonoid was previously shown to enhance the conversion rate of Te^IV by approximately 11-fold. In this study, we demonstrated that this was associated with the added benefit of reducing the toxic impact of Te^IV towards the methanogenic consortium in the UASB and thus enabled a 4.7-fold higher conversion rate of the chemical oxygen demand. Taken as a whole, this work demonstrates the potential of a methanogenic granular sludge to be applied as a bioreactor technology producing recoverable Te⁰ NPs in a continuous fashion.

Microbial toxicity of ionic species leached from the II-VI semiconductor materials, cadmium telluride (CdTe) and cadmium selenide (CdSe)

This work investigated the microbial toxicity of soluble species that can potentially be leached from the II-VI semiconductor materials, cadmium telluride and cadmium selenide. The soluble ions tested included: cadmium, selenite, selenate, tellurite, and tellurate. Their toxicity towards the acetoclastic and hydrogen-consuming trophic groups in a methanogenic consortium as well as towards a bioluminescent marine bacterium, Aliivibrio fischeri (Microtox(®) test), was assessed. The acetoclastic methanogenic activity was the most affected as evidenced by the low 50% inhibiting concentrations (IC50) values obtained of 8.6 mg L(-1) for both cadmium and tellurite, 10.2 mg L(-1) for tellurate, and 24.1 mg L(-1) for selenite. Both tellurium oxyanions caused a strong inhibition of acetoclastic methanogenesis at low concentrations, each additional increment in concentration provided progressively less inhibition increase. In the case of the hydrogenotrophic methanogenesis, cadmium followed by selenite caused the greatest inhibition with IC50 values of 2.9 and 18.0 mg L(-1), respectively. Tellurite caused a moderate effect as evidenced by a 36.8% inhibition of the methanogenic activity at the highest concentration tested, and a very mild effect of tellurate was observed. Microtox(®) analyses showed a noteworthy inhibition of cadmium, selenite, and tellurite with 50% loss in bioluminescence after 30 min of exposure of 5.5, 171.1, and 458.6 mg L(-1), respectively. These results suggest that the leaching of cadmium, tellurium and selenium ions from semiconductor materials can potentially cause microbial toxicity.