Solar-Powered Sustainable Water Production: State-of-the-Art Technologies for Sunlight-Energy-Water Nexus

Recent advances of copolymer for water treatment

Increasing water pollution due to anthropogenic activities prompts the quest for an effective water treatment method. Polymeric materials have gained attention as adsorbents for water purification. Membranes are majorly made from homopolymeric materials. However, recent studies have focused on using copolymeric materials for improved performance. In this review, the basics of copolymerization including various types of copolymers, synthetic approaches, and their applications in various water pollutants removal are discussed in detail. Advances in water treatment technology using copolymeric materials as adsorbent/membranes in the last 4 years are covered with insights into the future outlook and areas of improvement in terms of copolymer composites for water treatment. Studies from the literature did not only reveal effectiveness of copolymer as a flocculant/antifouling materials and in removal of selective toxic metals, oil, and microbes but also demonstrated recyclability of the copolymer sorbents/membrane. Full exploration of unique copolymer textural and structural properties could lead to great advancement in water treatment process. PRACTITIONER POINTS: The copolymer types and synthetic methods are discussed. Application of copolymer as adsorbent/membranes for water treatment is presented. Recent advances show good pollutants removal for toxic metals, oil, and organics. Copolymer composites have great potential as adsorbent/membranes for future use in water treatment processes.

A PAM hydrogel surface-coated hydroponic bamboo evaporator with efficient thermal utilization for solar evaporation

Solar-driven interfacial water purification emerges as a sustainable technology for seawater desalination and wastewater treatment to address the challenge of water scarcity. Currently, the energy losses via radiation and convection to surrounding environment minimize its energy efficiency. Therefore, it is necessary to develop strategies to minimize the heat losses for efficient water purification. Here, a novel evaporator was developed through the in situ gelation of PAM hydrogel on the surface carbonized hydroponic bamboo (PSC) to promote energy efficiency. The inherent porous and layered network structures of bamboo, in synergy with the functional hydration capacity of PAM hydrogel, facilitated adequate water transportation, while reducing evaporation enthalpy. The PAM hydrogel firmly covered on the photothermal layer surface effectively minimized the radiation and convection heat losses, while further harvesting those thermal energy that would otherwise dissipate into the surrounding environment. The reduced thermal conductivity of PSC served as a thermal insulator as well, obstructing heat transfer to bulk water and thus diminishing conduction losses. Consequently, the rational designed PSC could efficiently convert solar energy to purified water, leading to the evaporation of 2.09 kg m-2 h-1, the energy efficiency of 87.6 % under one sun irradiation, and yielding 9.6 kg m-2 fresh water over 11 h outdoor operation. Moreover, the PSC also performs excellent salt rejection, and long-term stability at outdoor experiment. These results demonstrated high and stable solar evaporation performance could be achieved if turning heat losses into a way of extra energy extraction to further enhance the evaporation performance. This strategy appears to be a promising strategy for effective thermal energy management and practical application.

Dynamical Janus-Like Behavior Excited by Passive Cold-Heat Modulation in the Earth-Sun/Universe System: Opportunities and Challenges

The utilization of solar-thermal energy and universal cold energy has led to many innovative designs that achieve effective temperature regulation in different application scenarios. Numerous studies on passive solar heating and radiation cooling often operate independently (or actively control the conversion) and lack a cohesive framework for deep connections. This work provides a concise overview of the recent breakthroughs in solar heating and radiation cooling by employing a mechanism material in the application model. Furthermore, the utilization of dynamic Janus-like behavior serves as a novel nexus to elucidate the relationship between solar heating and radiation cooling, allowing for the analysis of dynamic conversion strategies across various applications. Additionally, special discussions are provided to address specific requirements in diverse applications, such as optimizing light transmission for clothing or window glass. Finally, the challenges and opportunities associated with the development of solar heating and radiation cooling applications are underscored, which hold immense potential for substantial carbon emission reduction and environmental preservation. This work aims to ignite interest and lay a solid foundation for researchers to conduct in-depth studies on effective and self-adaptive regulation of cooling and heating.

Salt-rejecting 3D cone flowing evaporator based on bilayer photothermal paper for high-performance solar seawater desalination

Solar energy-driven water evaporation technology is a promising, low-cost and sustainable approach to alleviate the global clean water shortage, but usually suffers from low water evaporation rate and severe salt deposition on the water evaporation surface. In this work, a hydrophilic bilayer photothermal paper-based three-dimensional (3D) cone flowing evaporator was designed and prepared for stable high-performance seawater desalination with excellent salt-rejecting ability. The as-prepared bilayer photothermal paper consisted of MXene (Ti3C2Tx) and HAA (ultralong hydroxyapatite nanowires, poly(acrylic acid), and poly(acrylic acid-2-hydroxyethyl ester)). The accordion-like multilayered MXene acted as the efficient solar light absorber, and ultralong hydroxyapatite (HAP) nanowires served as the thermally insulating and supporting skeleton with a porous networked structure. A siphon effect-driven unidirectional fluid transportation unit in the 3D cone flowing evaporator could guide the concentrated saline flowing away from the evaporating surface to prevent salt deposition on the evaporation surface, avoiding severe deterioration of the performance in solar water evaporation. Furthermore, combining high solar light absorption and high photothermal conversion efficiencies, low water evaporation enthalpy (1838 ± 11 J g-1), and additional energy taken from the ambient environment, the as-prepared cone flowing evaporator exhibited a high water evaporation rate of 3.22 ± 0.20 kg m-2 h-1 for real seawater under one sun illumination (1 kW m-2), which was significantly higher than many values reported in the literature. This study provides an effective approach for designing high-performance solar energy-driven water evaporators for sustainable seawater desalination and wastewater purification.

In situ MIL-101 growth on cotton cloth to fabricate multifunctional phase change composites driven by solar and magneto-thermal for all-day desalination

It is certainly one of the most feasible ways to extract fresh water from seawater in the face of the current depletion of fresh water resources. Although solar energy as a heat source for desalination is the cleanest and most abundant way, its intermittent and seasonal also poses an obstacle to its practical application. In order to solve the above-mentioned issues, we prepared a series of phase change composites (PCCs) with excellent light-absorbing and magnetic properties by growing MIL-101(Fe) in situ on cotton fabric. All-day desalination through the synergistic action of phase change material (PCM) and magnetic particles. The evaporation rate of PCC can reach 2.76 kg m-2h-1 with an evaporation efficiency of 90.19 % under one sunlight condition. The evaporation rate of sea water under the synergistic effect of magnetic particles and PCM reached 4.53 kg m-2h-1 in the absence of sunlight. This paper provides a new approach to all-day desalination without contact heating.

Superhydrophobic sand evaporator with core-shell structure for long-term salt-resistant solar desalination

Solar-driven water evaporation, as an environmentally benign pathway, provides an opportunity for alleviating global clean water scarcity. However, the rapidly generated interfacial steam and localized heating could cause increased salt concentration and accumulation, deteriorating the evaporation performance and long-term stability. Herein, a novel superhydrophobic sand solar (FPPSD) evaporator with a core-shell structure was proposed through interface functionalization for continuous photothermal desalination. The collective behavior essence of the sand aggregate gave itself micron-scale self-organized pores and configurable shapes, generating desirable capillary force and supplying effective water-pumping channels. More importantly, combining the dopamine, polypyrrole (PPy), and 1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTS) through π-π conjugation and multiple hydrogen bonding effects gave the FPPSD evaporator with stable superhydrophobic property and highly efficient photothermal conversion capability. Therefore, the FPPSD evaporator showed a continuous and stable photothermal performance even after 96 h continuous evaporation under 3-sun irradiation for 10 wt% saline solution, among the best values in the reported works of literature, demonstrating its excellent salt-resistance stability. Furthermore, this novel FPPSD evaporator displayed outstanding environmental stability that kept its initial water transport capacity even after being treated under harsh conditions for 30 days. With excellent salt-resistance ability and stable environmental stability, the FPPSD evaporator will provide an attractive platform for sustainable solar-driven water management.

High-Entropy Photothermal Materials

High-entropy (HE) materials, celebrated for their extraordinary chemical and physical properties, have garnered increasing attention for their broad applications across diverse disciplines. The expansive compositional range of these materials allows for nuanced tuning of their properties and innovative structural designs. Recent advances have been centered on their versatile photothermal conversion capabilities, effective across the full solar spectrum (300-2500 nm). The HE effect, coupled with hysteresis diffusion, imparts these materials with desirable thermal and chemical stability. These attributes position HE materials as a revolutionary alternative to traditional photothermal materials, signifying a transformative shift in photothermal technology. This review delivers a comprehensive summary of the current state of knowledge regarding HE photothermal materials, emphasizing the intricate relationship between their compositions, structures, light-absorbing mechanisms, and optical properties. Furthermore, the review outlines the notable advances in HE photothermal materials, emphasizing their contributions to areas, such as solar water evaporation, personal thermal management, solar thermoelectric generation, catalysis, and biomedical applications. The review culminates in presenting a roadmap that outlines prospective directions for future research in this burgeoning field, and also outlines fruitful ways to develop advanced HE photothermal materials and to expand their promising applications.

Biopolymers for Hygroscopic Material Development

The effective management of atmospheric water will create huge value for mankind. Diversified and sustainable biopolymers that are derived from organisms provide rich building blocks for various hygroscopic materials. Here, a comprehensive review of recent advances in developing biopolymers for hygroscopic materials is provided. It is begun with a brief introduction of species diversity and the processes of obtaining various biopolymer materials from organisms. The fabrication of hygroscopic materials is then illustrated, with a specific focus on the use of biopolymer-derived materials as substrates to produce composites and the use of biopolymers as building blocks to fabricate composite gels. Next, the representative applications of biopolymer-derived hygroscopic materials for dehumidification, atmospheric water harvesting, and power generation are systematically presented. An outlook on future challenges and key issues worthy of attention are finally provided.

Phospholipid Bilayer Inspired Sandwich Structural Nanofibrous Membrane for Atmospheric Water Harvesting and Selective Release

Atmospheric water harvesting (AWH) has been broadly exploited to meet the challenge of water shortage. Despite the significant achievements of AWH, the leakage of hydroscopic salt during the AWH process hinders its practical applications. Herein, inspired by the unique selective permeability of the phospholipid bilayer, a sandwich structural (hydrophobic-hydrophilic-hydrophobic) polyacrylonitrile nanofibrous membrane (San-PAN) was fabricated for AWH. The hydrophilic inner layer loaded with LiCl could capture water from the air. The hydrophobic microchannels in the outer layer could selectively allow the free transmission of gaseous water molecules but confine the hydroscopic salt solution in the hydrophilic layer, achieving continuous and recyclable water sorption/desorption. As demonstrated, the as-prepared AWH devices presented high-efficient adsorption kinetics from 1.66 to 4.08 g g-1 at 30% to 90% relative humidity. Thus, this work strengthens the understanding of the water transmission process along microchannels and provides insight into the practical applications of AWH.

Towards a better understanding of atmospheric water harvesting (AWH) technology

Atmospheric water harvesting (AWH) technology is an emerging sustainable development strategy to deal with global water scarcity. To better understand the current state of AWH technology development, we conducted a bibliometric analysis highlighting three water harvesting technologies (fog harvesting, condensation, and sorption). By comprehensively reviewing the research progress and performing a comparative assessment of these technologies, we summarized past achievements and critically analyzed the different technologies. Traditional fog collectors are more mature, but their efficiency still needs to be improved. External field-driven fog harvesting and active condensation need to be driven by external forces, and passive condensation has high requirements for environmental humidity. Emerging bio-inspired fog harvesting and sorption technology provide new possibilities for atmospheric water collection, but they have high requirements for materials, and their commercial application is still to be further promoted. Based on the key characteristics of each technology, we presented the development prospects for the joint use of integrated/hybrid systems. Next, the water-energy relationship is used as a link to clarify the future development strategy of AWH technology in energy driving and conversion. Finally, we outlined the core ideas of AWH for both basic research and practical applications and described its limitless possibilities for drinking water supply and agricultural irrigation. This review provides an essential reference for the development and practical application of AWH technologies, which contribute to the sustainable utilization of water resources globally.

3D-Printed Liquid Metal-in-Hydrogel Solar Evaporator: Merging Spectrum-Manipulated Micro-Nano Architecture and Surface Engineering for Solar Desalination

Solar desalination driven by interfacial heating is considered a promising technique to alleviate the freshwater shortage crisis. However, its further extension and application are confined by factors such as highlighted salt accumulation, inferior energy efficiency, and poor durability. Herein, a microsized eutectic gallium-indium (EGaIn) core-shell nanodroplet (denoted as LMTE) with photo-cross-linking and photothermal traits, stabilized by allyl glycidyl ether (AGE)-grafting tannic acid (TA), is explored as the solar absorber for broadband light absorbing and localized micro-nano heat channeling. The LMTE nanodroplets are formulated directly with highly hydrated polymers and photosensitive species to successfully develop a water-based photothermal ink suitable for digital light processing (DLP) 3D printing. As a demonstration, the LMTE composite hydrogel-forged milli-conical needle arrays with metal-phenolic network (MPN)-engineered wettability and photothermal enhancement can be printed by the digital light processing (DLP) technique and designed rationally via a bottom-up strategy. The 3D-printing hydrogel evaporator is composed of spectrum-tailored EGaIn nanodroplets for efficient photon harvesting and MPN-coated milli-cone arrays for water supplying with micro-nano channeling, which function cooperatively to bestow the 3D solar evaporator with superior solar-powered water evaporation (2.96 kg m-2 h-1, 96.93% energy efficiency) and excellent solar desalination (salt cycle and site-specific salt crystallization). Furthermore, a robust steam generating/collecting system of the 3D solar evaporator is demonstrated, providing valuable guidance for building a water-energy-agriculture nexus.

Improved solar-driven water purification using an eco-friendly and cost-effective aerogel-based interfacial evaporator with exceptional photocatalytic capabilities

As a promising solution to address the global challenge of freshwater scarcity, solar-powered interfacial steam generation has undergone notable advancements. This study introduces a novel solar-driven interfacial evaporation membrane (ZnIn2S4@SiO2/ACSA, ZSAS) comprising a ZnIn2S4@SiO2 composite and a black sodium alginate aerogel infused with activated carbon. The ZSAS membrane demonstrates exceptional light absorption and thermal insulation, leading to elevated surface temperatures and reduced heat dissipation into the bulk water. Furthermore, the incorporation of AC reinforces the mechanical properties of the ZSAS membrane and enhances the water purification performance. These collective features result in an impressive evaporation rate of 1.485 kg m-2 h-1 and a high photothermal conversion efficiency of 91.2% under 1 sun irradiation for the optimal ZSAS membrane. Moreover, the optimal ZSAS membrane can effectively remove salts, heavy metal ions, and organic pollutants, benefitting from its superior evaporation separation effect and the photocatalytic properties of the ZnIn2S4@SiO2 composite.

Engineering High-Tortuosity 3D Gradient Structure and CFD-Assisted Multifield Analysis for Solar Interfacial Evaporation

Solar interfacial evaporation is a promising method for solving the global shortage of fresh water. While 2D evaporators can efficiently localize solar-converted heat at the thin layer of the water-air interface, 3D solar evaporators can maximize energy reutilization while maintaining effective mass transport ability, few studies are conducted to explore the effect of gradient porosity on evaporation performance. In this study, a multifield assisted strategy based on a gradient 3D structure with high tortuosity is proposed, which creates a thermal field environment for efficient evaporation through high absorption of sunlight and excellent photothermal conversion and uses the gradient structure to optimize the internal pressure field to enhance water evaporation and transport. This hierarchically nanostructured solar absorber, with porosity inhomogeneity-induced pressure gradient and optimized temperature management, is a valuable design idea for manufacturing a more efficient 3D solar evaporator in the field of seawater desalination. Owing to the understanding of optimizing the dimension by various simulation parameters, the evaporation efficiencies of such structures are found to be 165.7%, suppressing the most evaporator. Moreover, it can provide new ideas and references for the fields of mass transfer and thermal management.

Boosting the Viable Water Harvesting in Solar Vapor Generation: From Interfacial Engineering to Devices Design

Continuously increasing demand for the life-critical water resource induces severe global water shortages. It is imperative to advance effective, economic, and environmentally sustainable strategies to augment clean water supply. The present work reviews recent reports on the interfacial engineering to devices design of solar vapor generation (SVG) system for boosting the viability of drinkable water harvesting. Particular emphasis is placed on the basic principles associated with the interfacial engineering of solar evaporators capable of efficient solar-to-thermal conversion and resulting freshwater vapor via eliminating pollutants from quality-impaired water sources. The critical configurations manufacturing of the devices for fast condensation is then highlighted to harvest potable liquid water. Fundamental and practical challenges, along with prospects for the targeted materials architecture and devices modifications of SVG system are also outlined, aiming to provide future directions and inspiring critical research efforts in this emerging and exciting field.

Distribution-according-to-work: Enhancing solar vapor generation of photothermal sponge by using cellulose-based water storage platform

Interfacial solar vapor generation (ISVG) has shown extraordinary promise in achieving high-efficiency water purification. However, the rapid water supply often leads to excessive water in the solar absorber, resulting in undesired heat loss and a decrease in evaporation rate. To tackle this issue, we developed a bio-based solar evaporator comprising cellulose-based water retention resin (CRR) and straw-derived photothermal sponge. CRR serves as an effective water storage platform with a high binding capacity for water molecules, preventing water from entering the absorber and reducing the water evaporation enthalpy. The water management of CRR confines the solar-to-vapor conversion to the interface between CRR and the photothermal sponge, thereby eliminating the adverse effects of excess water. Additionally, the ISVG process operates based on the principle of Distribution-according-to-work, meaning that the quantity of generated vapor depends on the evolution of the sponge structure. Optimal sponge configuration enables evaporation rates of 2.28 and 1.53 kg/m2/h under solar irradiation of 1.0 and 0.5 kW/m2, respectively. Additionally, the obtained evaporator is capable of producing 7.1 kg/m2/day of freshwater in outdoor experiment. This report proposes a novel approach to designing an ISVG device that incorporates effective water management strategy for achieving high-efficiency water purification in real-world scenarios.

Multiscale Synergetic Bandgap/Structure Engineering in Semiconductor Nanofibrous Aerogels for Enhanced Solar Evaporation

Solar-driven interface evaporation has been identified as a sustainable seawater desalination and water purification technology. Nonetheless, the evaporation performance is still restricted by salt deposition and heat loss owing to weak solar spectrum absorption, tortuous channels, and limited plane area of conventional photothermal material. Herein, the semiconductor nanofibrous aerogels with a narrow bandgap, vertically aligned channels, and a conical architecture are constructed by the multiscale synergetic engineering strategy, encompassing bandgap engineering at the atomic scale and structure engineering at the nano-micro scale. As a proof-of-concept demonstration, a Co-doped MoS2 nanofibrous aerogel is synthesized, which exhibits the entire solar absorption, superhydrophilic, and excellent thermal insulation, achieving a net evaporation rate of 1.62 kg m-2 h-1 under 1 sun irradiation, as well as a synergistically efficient dye ion adsorption function. This work opens up new possibilities for the development of solar evaporators for practical applications in clean water production.

Rational Construction of a Triple-Phase Reaction Zone Using CuO-Based Heterostructure Nanoarrays for Enhanced Water Oxidation Reaction

The development of high-efficiency oxygen evolution reaction (OER) electrocatalysts for the production and conversion of clean energy is paramount yet also full of challenges. Herein, we proposed a simple and universal method to precisely fabricate the hierarchically structured CuO/TMOs loaded on Cu foil (CuO/TMOs/CF) (TMO represents Mn3O4, NiO, CoO, and CuO) nanorod-array electrodes as a highly active and stable OER electrocatalyst, employing Cu(OH)2/CF as a self-sacrificing template by the subsequent H2O2-induced chemical deposition (HiCD) and pyrolysis process. Taking CuO/Mn3O4/CF as an example, we systematically investigated its structure-performance relationship via experimental and theoretical explorations. The enhanced OER activity can be ascribed to the rational design of the nanoarray with multiple synergistic effects of abundant active sites, excellent electronic conductivity of the metallic Cu foil substrate, strong interface charge transfer, and quasi-superhydrophilic/superaerophobic property. Consequently, the optimal CuO/Mn3O4/CF presents an overpotential of 293 mV to achieve a current density of 20 mA cm-2 in 1.0 M KOH media, comparable to that of commercial RuO2 (282 mV), delivering excellent durability by the electrolysis of water at a potential of around 1.60 V [vs reversible hydrogen electrode (RHE)] without evident degeneration. This work might offer a feasible scheme for developing a hybrid nanoarray OER electrocatalyst via regulating electron transportation and mass transfer.

Trickling filter systems for sustainable water supply: An evaluation of eco-environmental burdens and greenhouse gas emissions

Despite the global water crisis, the significant potential of trickling filter systems as a crucial auxiliary option for sustainable water supply has received insufficient attention. Therefore, this study presents the first-ever evaluation of the environmental impacts of trickling filter application in wastewater treatment, focusing on eco-environmental burdens. Additionally, the study explores greenhouse gas emissions, energy, and exergy footprints, providing novel insights into the environmental implications of using trickling filters for wastewater treatment. The study's findings indicate that the consumption of heat and electricity in trickling filters has significant environmental impacts, particularly on land use (93.24%), freshwater/marine eutrophication (∼81.98%), and human health (45.36%). The majority of the energy required for trickling filter operation is supplied by fossil fuels (96.02%), resulting in increased greenhouse gas emissions (65.58%). The exergy of trickling filters is highly efficient, accounting for over 95% of the system's energy. Mathematical modeling reveals that anaerobic digestion and secondary clarifier have the highest energy consumption, with contributions of 94.65% and 2.63%, respectively. Construction expenses account for almost 88% of the total cost, with anaerobic digestion (42.15%) and trickling filters (35.39%) being the most costly components. The cost of treating 1 m3 of wastewater is estimated at 0.52 $/m3. Sensitivity analysis demonstrates that electricity (14.66%) and heat (18.65%) significantly impact terrestrial ecotoxicity and land use, respectively. This study presents a framework for future investigations in this field.

Ion sieving membrane for direct seawater anti-precipitation hydrogen evolution reaction electrode

In seawater, severe hydroxide-based precipitation on the hydrogen evolution reaction (HER) electrode surface is still a major stumbling block for direct seawater electrolysis. Here, we design a direct seawater HER electrode with excellent anti-precipitation performance based on an Ni(OH)2 nanofiltration membrane in situ grown on nickel foam (NF) at room temperature. The positively charged Ni(OH)2 membrane with nanometer-scale cracks realises an ion sieving function, which apparently hinders the transfer of Mg2+/Ca2+ ions to suppress precipitation, while rapidly transporting OH- and H2O to ensure HER mass transfer. Therefore, the Ni(OH)2-membrane-decorated seawater HER electrode reduces precipitation by about 98.3% and exhibits high activity and stability. Moreover, in the application of a direct seawater electrolyser and magnesium seawater battery, the Ni(OH)2 membrane-decorated electrode also shows low precipitation and high stability. This work highlights a potential strategy to solve HER electrode precipitation in seawater via an ingenious electrode structure design.

Bimetallic MOF-Derived Solar-Triggered Monolithic Adsorbent for Enhanced Atmospheric Water Harvesting

The development of economical, energy-saving, and efficient metal-organic framework (MOF)-based adsorbents for atmospheric water collection is highly imperative for the rapid advancement of renewable freshwater resource exploitation. Herein, a feasible one-step solvothermal formation strategy of bimetallic MOF (BMOF) is proposed and applied to construct a solar-triggered monolithic adsorbent for enhanced atmospheric water collection. Benefiting from the reorganization and adjustment of topology structure by Al atoms and Fe atoms, the resultant BMOF(3) consisting of Al-fumarate and MIL-88A has a higher specific surface area (1202.99 m2  g-1 ) and pore volume (0.51 cm3  g-1 ), thereby outperforming the parental MOFs and other potential MOFs in absorbing water. Expanding upon this finding, the solar-triggered monolithic adsorbent is further developed through a bottom-up assembly of polyaniline/chitosan layers and hybridized BMOF(3) skeletons on a glass fiber support. The resultant monolithic adsorbent exhibits superior sorption-desorption kinetics, leading to directional water transport and rapid solar-assisted vapor diffusion. As a proof-of-concept demonstration, an exquisite water harvester is constructed to emphasize a high water yield of 1.19 g g-1 per day of the designed monolithic adsorbent. Therefore, the design and validation of bimetallic MOF-derived solar-triggered adsorbent in this work are expected to provide a reference for the large-scale applications of MOF-based atmospheric water harvesting.

Ca-MOF-Derived Porous Sorbents for High-Yield Solar-Driven Atmosphere Water Harvesting

The development of high-yield, metal-organic framework (MOF)-based water harvesters in arid areas remains challenging due to the absence of effective strategies for enhancing water sorption capacity and kinetics. Herein, we presented a novel strategy for in situ fabrication of calcium chloride (CaCl2) decorated MOF-derived porous sorbents (PCC-42) through pyrolysis Ca-MOF and subsequently hydrochloric acid (HCl) vapor treatment process. The resulting PCC-42 sorbents exhibited a high water adsorption capacity of 3.04 g g-1 at 100% relative humidity (RH), outstanding photothermal performance, and rapid water uptake-release kinetics, surpassing most reported MOFs adsorbents. At 20, 30, 40, and 50% RH, PCC-42 demonstrated water uptake capacity of 0.45, 0.59, 0.76, and 0.9 g g-1, which represented an increase of 421 and 940% (at 20% RH) and 333 and 351% (at 30% RH) compared to Ca-MOF and CaCl2·2H2O, respectively. Approximately 80% of the adsorbed water in PCC-42 could be released under one sun within 50 min. Indoor water harvesting experiments demonstrated that PCC-42 is a promising adsorbent for various humidity environments. Additionally, outdoor solar-driven atmospheric water harvesting (AWH) tests revealed a high daily water production of 1.13 L/kgadsorbent under typical arid conditions (30-60% RH). The proposed strategy helps the design of high-performance adsorbents for solar-driven AWH in arid environments.

Natural Cellulose Fiber-Derived Photothermal Aerogel for Efficient and Sustainable Solar Desalination

Aerogels are becoming a promising platform to fabricate photothermal materials for use in solar steam generation (SSG), which have remarkable application potential in solar desalination, due to their excellent thermal management, salt resistance, and considerable water evaporation rate. In this work, a novel photothermal material is fabricated by forming a suspension between sugarcane bagasse fibers (SBF) and poly(vinyl alcohol), tannic acid (TA), and Fe³⁺ solutions via hydrogen bonds of hydroxyl groups. After freeze drying, the fabricated SBF aerogel-based photothermal (SBFAP) material possesses a 3D interconnected porous microstructure, which could enhance water transportation ability, reduce thermal conductivity, and quickly dissolve salt crystals on the SBFAP surface. Thanks to the formation of micro/nanosized complexes between TA and Fe³⁺ ions on the SBFAP material, the SBFAP exhibits high light capture and water evaporation rate (2.28 kg m^-2 h^-1). In particular, due to strong hydrogen bonding and the SBF, the SBFAP material is reinforced, thereby exhibiting excellent structural stability in seawater. Moreover, the high salt tolerance of SBFAP favors its high desalination performance for at least 76 days of continuous evaporation under actual conditions. This research paves the way for the fabrication of natural cellulose fiber-based photothermal materials for application in solar desalination.

Bioinspired Aerogel with Vertically Ordered Channels and Low Water Evaporation Enthalpy for High-Efficiency Salt-Rejecting Solar Seawater Desalination and Wastewater Purification

Solar energy-driven water evaporation is a promising sustainable strategy to purify seawater and contaminated water. However, developing solar evaporators with high water evaporation rates and excellent salt resistance still faces a great challenge. Herein, inspired by the long-range ordered structure and water transportation capability of lotus stem, a biomimetic aerogel with vertically ordered channels and low water evaporation enthalpy for high-efficiency solar energy-driven salt-resistant seawater desalination and wastewater purification is developed. The biomimetic aerogel consists of ultralong hydroxyapatite nanowires as heat-insulating skeletons, polydopamine-modified MXene as a photothermal material with broadband sunlight absorption and high photothermal conversion efficiency, polyacrylamide, and polyvinyl alcohol as reagents to lower the water evaporation enthalpy and as glues to enhance the mechanical performance. The honeycomb porous structure, unidirectionally aligned microchannels, and nanowire/nanosheet/polymer pore wall endow the biomimetic aerogel with excellent mechanical properties, rapid water transportation, and excellent solar water evaporation performance. The biomimetic aerogel exhibits a high water evaporation rate (2.62 kg m^-2  h^-1 ) and energy efficiency (93.6%) under one sun irradiation. The superior salt-rejecting ability of the designed water evaporator enables stable and continuous seawater desalination, which is promising for application in water purification to mitigate the global water crisis.

Efficient Fabrication of Micro/Nanostructured Polyethylene/Carbon Nanotubes Foam with Robust Superhydrophobicity, Excellent Photothermality, and Sufficient Adaptability for All-Weather Freshwater Harvesting

The integration of fog collection and solar-driven evaporation has great significance in addressing the challenge of the global freshwater crisis. Herein, a micro/nanostructured polyethylene/carbon nanotubes foam with interconnected open-cell structure (MN-PCG) is fabricated using an industrialized micro extrusion compression molding technology. The 3D surface micro/nanostructure provides sufficient nucleation points for tiny water droplets to harvest moisture from humid air and a fog harvesting efficiency of 1451 mg cm^-2 h^-1 is achieved at night. The homogeneously dispersed carbon nanotubes and the graphite oxide@carbon nanotubes coating endow the MN-PCG foam with excellent photothermal properties. Benefitting from the excellent photothermal property and sufficient steam escape channels, the MN-PCG foam attains a superior evaporation rate of 2.42 kg m^-2 h^-1 under 1 Sun illumination. Consequently, a daily yield of ≈35 kg m^-2 is realized by the integration of fog collection and solar-driven evaporation. Moreover, the robust superhydrophobicity, acid/alkali tolerance, thermal resistance, and passive/active de-icing properties provide a guarantee for the long-term work of the MN-PCG foam during practical outdoor applications. The large-scale fabrication method for an all-weather freshwater harvester offers an excellent solution to address the global water scarcity.

Theory of Anisotropic Metal Nanostructures

A significant challenge in the development of functional materials is understanding the growth and transformations of anisotropic colloidal metal nanocrystals. Theory and simulations can aid in the development and understanding of anisotropic nanocrystal syntheses. The focus of this review is on how results from first-principles calculations and classical techniques, such as Monte Carlo and molecular dynamics simulations, have been integrated into multiscale theoretical predictions useful in understanding shape-selective nanocrystal syntheses. Also, examples are discussed in which machine learning has been useful in this field. There are many areas at the frontier in condensed matter theory and simulation that are or could be beneficial in this area and these prospects for future progress are discussed.

Facile fabrication of Ni5P4-NiMoOx nanorod arrays with synergistic thermal management for efficient interfacial solar steam generation and water purification

Interfacial steam generation by harnessing renewable solar energy has been recognized as a sustainable solution to global freshwater crisis. A promising evaporator with key components of high spectral absorption, efficient thermal management and adequate water transport is highly desired. In the present study, an integrated design for three-in-one functionality is achieved by simply loading Ni₅P₄-NiMoO_x (P-NMO) on a macroporous nickel foam (NF) carrier. In situ embedding broadband Ni₅P₄ absorber into insulating NiMoO_x enables efficient photothermal conversion and heat localization. Benefiting from proper thermal management and abundant water transmission, P-NMO/NF exhibits the excellent performance for interfacial steam generation with a high evaporation rate of 1.49 kg m^-2h^-1 and evaporation efficiency of 93.0 % under one sun irradiation. Furthermore, the obtained P-NMO/NF is proven to be applicable for high-efficiency freshwater production in seawater desalination and wastewater purification, showing great potential for practical solar evaporator under natural environmental conditions.

Wooden Solar Evaporator Design Based on the Water Transpiration Principle of Trees

The double-sided carbonization of poplar with different sections forms a three-layer structure inspired by tree water transpiration. A photothermal evaporation comparison experiment was conducted to simulate the influence of solar radiation intensity (1 kW·m^-2) on uncarbonized and single- and double-sided carbonized poplar specimens. The tissue structure, chemical functional group changes, and profile density of the specimens were analyzed using scanning electron microscopy, Fourier transform infrared spectrometry, and X-ray profile density testing, respectively. The results showed that the tissue structure of the specimen changed after treatment, and the relationship of water evaporation was shown as follows: cross-section (C) > Radial section (R) > Tangential section (T), and Double-sided carbonized poplar (DCP) > Single-sided carbonized poplar (SCP) > Non-carbonized poplar (NCP). Of these, the maximum photothermal evaporation was from the cross-section of the double-sided carbonized poplar (NCPC) with a value of 1.32 kg·m^-2·h^-1, which was 21.97% higher than single-sided carbonized poplar (SCPC) and 37.88% higher than non-carbonized poplar (NCPC). Based on the results, double-sided carbonization three-layer structure treatment can improve the evaporation force of the poplar interface, thereby improving the moisture migration ability of wood, and can be applied to solar interface absorber materials.

Emerging Materials for Interfacial Solar-Driven Water Purification

Solar-driven water purification is considered as an effective and sustainable technology for water treatment using green solar energy. One major goal for practical applications is to improve the solar evaporation performance by the design of novel photothermal materials, with optimized heat localization and water transport pathways to achieve reduced energy consumption for water vaporization. Recently, some emerging materials like polymers, metal-organic frameworks (MOFs), covalent organic frameworks (COFs) and also single molecules were employed to construct novel solar evaporation systems. In this minireview, we present an overview of the recent efforts on materials development for water purification systems. The state-of-the-art applications of these emerging materials for solar-driven water treatment, including desalination, wastewater purification, sterilization and energy production, are also summarized.

Indicators, Goals, and Assessment of the Water Sustainability in China: A Provincial and City-Level Study

The United Nations and scholars called for more attention and efforts for cleaner water and water sustainability. This study established a water sustainability evaluating method framework, including indicators, goals, and methods and performs provincial and city-level assessments as case studies. The framework involves six fields, surface water quality, marine environmental quality, water-soil-agriculture, water infrastructure, water conservation, aquatic ecology, water-efficient use, and pollutant emission reduction. The methods innovatively integrate multi fields and concerns of water sustainability while providing a goal-oriented evaluation and implementing the United Nations' call for the refinement and clarification of SDGs. China's overall water sustainability was evaluated as 0.821 in 2021, and have performed well in surface water quality, sea quality, water conservation, and aquatic ecology fields while performing poorly in the water-soil-agriculture field. The overall strategy, policy, and action for water sustainability could be developed based on the evaluation. The water sustainability evaluation presented the regional and field/indicator differentiations. It is necessary to implement regionally classified policies and differentiated management for sustainable water development. The correlation analysis with socioeconomic factors implies the complicated and intimate interaction between socioeconomic development and water sustainability while revealing that development stages and the inherent conditions of natural ecology and water sources bring about the differentiations. A comprehensive evaluation of water sustainability may be three-dimensional, involving water quality and ecology, development related to water, and water resources and utilization.

Research on a Coordination Evaluation and Prediction Model of Water Use and Industrial Ecosystem Development

Coordinating the relationship between water use and industrial ecosystem development is the key to ensuring high-quality and sustainable development of the industrial economy. In this paper, a model was proposed for evaluating and predicting the coordination between water use and industrial ecosystem development. First, aiming at the coordination of water use and industrial ecosystem development, this paper determined 15 indicators from the aspects of water demand and supply, water conservation and environmental protection, industrial sustainable development, input and output, and industrial development status. The combination weighting method based on game theory was used to determine the weight of the evaluation index. Then, the coordination evaluation model called the back propagation neural network (BP)-coupling coordination degree model (CCDM) and the coordination prediction model called gray models (GM)-BP-CCDM were established. Finally, the model was applied to the coordination evaluation and prediction of water use and industrial ecosystem development in the Hebei Province, China. The results show that the coordination degree of cities in the Hebei Province is moderate. Therefore, based on the research results, some scientific and reasonable suggestions for water resources utilization and industrial ecosystem development were put forward.

A flexible, high-efficiency, and low-cost FeS2@CTS hydrogel film for solar interface water evaporation

Solar interfacial water evaporation to obtain pure water has attracted extensive attention in recent years. In this work, based on the excellent optical property of FeS2 and the cross-linking nanostructure of chitosan (CTS), a FeS2@CTS hydrogel composite film for solar interfacial water evaporation was developed by hydrothermal synthesis and the following composite coating technology. The prepared FeS2@CTS presented high solar absorptivity of 95.27% and fast optical response capability. Under the optimized condition, the evaporation rate of pure water reached 3.34 kg m−2 h−1 and the photothermal conversion efficiency was 103.06% under one sun irradiation. In five runs, the evaporation rate of the FeS2@CTS was stable, indicating the excellent cycle stability. Also, in the desalination test, the stable evaporation rate of 1.74 kg m−2 h−1 was obtained in five runs. Due to the simple preparation method, low cost, and outstanding interfacial evaporation property, this FeS2@CTS indicates great potential for the seawater desalination or other photothermal conversion applications.

A bioinspired antibacterial and photothermal membrane for stable and durable clean water remediation

Solar-driven steam generation has been considered as a prevalent and sustainable approach to obtain clean fresh water. However, the presence of microorganisms in seawater may cause the biofouling and degradation of polymeric photothermal materials and clog the channels for water transportation, leading to a decrease in solar evaporation efficiency during long-term usage. Herein, we have reported a facile strategy to construct a robust cellulose membrane device coated by tobramycin-doped polydopamine nanoparticles (PDA/TOB@CA). The PDA/TOB@CA membrane not only exhibited synergistic antibacterial behaviors with long-term and sustained antibiotic release profiles, but also achieved a high water evaporation rate of 1.61 kg m^-2 h^-1 as well as an evaporation efficiency of >90%. More importantly, the high antibacterial activity endowed the PDA/TOB@CA membrane with superb durability for stable reuse over 20 cycles, even in microbe-rich environments. Therefore, we envision that this study could pave a new pathway towards the design and fabrication of robust antibacterial and photothermal materials for long-term and stable clean water production.

Electrospun Nanofibrous Membranes: A Versatile Medium for Waterproof and Breathable Application

Waterproof and breathable membranes that prevent liquid water penetration, while allowing air and moisture transmission, have attracted significant attention for various applications. Electrospun nanofiber materials with adjustable pore structures, easily tunable wettability, and good pore connectivity, have shown significant potential for constructing waterproof and breathable membranes. Herein, a systematic overview of the recent progress in the design, fabrication, and application of waterproof and breathable nanofibrous membranes is provided. The various strategies for fabricating the membranes mainly including one-step electrospinning and post-treatment of nanofibers are given as a starting point for the discussion. The different design concepts and structural characteristics of each type of waterproof and breathable membrane are comprehensively analyzed. Then, some representative applications of the membranes are highlighted, involving personal protection, desalination, medical dressing, and electronics. Finally, the challenges and future perspectives associated with waterproof and breathable nanofibrous membranes are presented.

A Highly Stable Ortho-Ketoenamine Covalent Organic Framework with Balanced Hydrophilic and Hydrophobic Sites for Atmospheric Water Harvesting

Atmospheric moisture is a sustainable clean water source that can solve the shortage of fresh water in arid areas. Herein a 2D covalent organic framework (COF-ok) was reported as a promising porous sorbent for solar-driven atmospheric water harvesting. COF-ok with ortho-ketoenamine linkage was extremely stable in harsh environment, including in boiling water, strong acids and bases. Because of the balanced hydrophilic and hydrophobic sites in channels, COF-ok showed a high water uptake of 0.33 g g^-1 at a low relative humidity of 34 % featuring a characteristic S-shaped water sorption isotherm with low regeneration temperature (∼45 °C) and excellent cyclic stability. A laboratory-scale water harvesting system could collect water of 161 g kg^-1 under sunlight.

Hygroscopic Porous Polymer for Sorption-Based Atmospheric Water Harvesting

Sorption-based atmospheric water harvesting (SAWH) holds huge potential due to its freshwater capabilities for alleviating water scarcity stress. The two essential parts, sorbent material and system structure, dominate the water sorption-desorption performance and the total water productivity for SAWH system together. Attributed to the superiorities in aspects of sorption-desorption performance, scalability, and compatibility in practical SAWH devices, hygroscopic porous polymers (HPPs) as next-generation sorbents are recently going through a vast surge. However, as HPPs' sorption mechanism, performance, and applied potential lack comprehensive and accurate guidelines, SAWH's subsequent development is restricted. To address the aforementioned problems, this review introduces HPPs' recent development related to mechanism, performance, and application. Furthermore, corresponding optimized strategies for both HPP-based sorbent bed and coupling structural design are proposed. Finally, original research routes are directed to develop next-generation HPP-based SAWH systems. The presented guidelines and insights can influence and inspire the future development of SAWH technology, further achieving SAWH's practical applications.

Photothermal Aerogel Beads Based on Polysaccharides: Controlled Fabrication and Hybrid Applications in Solar-Powered Interfacial Evaporation, Water Remediation, and Soil Enrichment

Solar-powered interfacial evaporation has emerged as an innovative and sustainable technology for clean water production. However, the rapid, mass and shape-controlled fabrication of three-dimensional (3D) steam generators (SGs) for versatile hybrid applications remains challenging. Herein, composite aerogel beads with self-contained properties (i.e., hydrophilic, porous, photothermal, and durable) are developed and demonstrated for threefold hybrid applications including efficient solar-powered interfacial evaporation, water remediation, and controlled soil enrichment. The rational incorporation of selected polysaccharides enables us to fabricate bead-like aerogels with rapid gelation, continuous processing, and enhanced ion adsorption. The composite beads can attain a high water evaporation rate of 1.62 kg m-2 h-1 under 1 sun. Meanwhile, high phosphate adsorption capacity of over 120 mg g-1 is achieved in broad pH (2.5-12.4) and concentration (200-1000 mg L-1) ranges of phosphate solutions. Gratifyingly, we demonstrate the first example of recycling biomaterials from interfacial SGs for controlled nutrient release, soil enrichment, and sustainable agriculture. The phosphate-saturated beads can be gradually broken down in the soil. Macronutrients (N, P, and K) can be slowly released in 50 days, sustaining the plant germination and growth in a whole growth stage. This work shines light on the mass and controlled fabrication of aerogel beads based on double-network biopolymers, not merely scaling up solar-powered interfacial evaporation but also considering water remediation, waste material disposal, and value-added conversion.

MXene-Based Porous Monoliths

In the past decade, a thriving family of 2D nanomaterials, transition-metal carbides/nitrides (MXenes), have garnered tremendous interest due to its intriguing physical/chemical properties, structural features, and versatile functionality. Integrating these 2D nanosheets into 3D monoliths offers an exciting and powerful platform for translating their fundamental advantages into practical applications. Introducing internal pores, such as isotropic pores and aligned channels, within the monoliths can not only address the restacking of MXenes, but also afford a series of novel and, in some cases, unique structural merits to advance the utility of the MXene-based materials. Here, a brief overview of the development of MXene-based porous monoliths, in terms of the types of microstructures, is provided, focusing on the pore design and how the porous microstructure affects the application performance.

Flower-Shaped Carbon Nanomaterials for Highly Efficient Solar-Driven Water Evaporation

Solar-driven interface water evaporation is an energy-saving, environmentally friendly, and efficient seawater desalination and wastewater treatment technology. However, some challenges still restrict its further industrial development, such as its complex preparation, heavy metal pollution, and insufficient energy utilization. In this study, a photothermal layer based on flower-shaped carbon nanoparticles is presented for highly efficient solar-driven interface evaporation for water treatment applications. The results show that the surface of the prepared carbon nanomaterials presents a flower-shaped structure with an excellent light absorption capacity and a large specific surface area. Moreover, the C-5.4 (Carbon-5.4) sample has an evaporation rate of 1.87 kg/m2/h and an evaporation efficiency of 87%—far higher than most photothermal materials. In addition, carbon nanomaterials have an excellent ion scavenging capacity, dye purification capacity, and outdoor practical performance. This study provides a new solution for the application of carbon nanomaterials in the field of water purification.

Versatile self-assembled electrospun micropyramid arrays for high-performance on-skin devices with minimal sensory interference

On-skin devices that show both high performance and imperceptibility are desired for physiological information detection, individual protection, and bioenergy conversion with minimal sensory interference. Herein, versatile electrospun micropyramid arrays (EMPAs) combined with ultrathin, ultralight, gas-permeable structures are developed through a self-assembly technology based on wet heterostructured electrified jets to endow various on-skin devices with both superior performance and imperceptibility. The designable self-assembly allows structural and material optimization of EMPAs for on-skin devices applied in daytime radiative cooling, pressure sensing, and bioenergy harvesting. A temperature drop of ~4 °C is obtained via an EMPA-based radiative cooling fabric under a solar intensity of 1 kW m^-2. Moreover, detection of an ultraweak fingertip pulse for health diagnosis during monitoring of natural finger manipulation over a wide frequency range is realized by an EMPA piezocapacitive-triboelectric hybrid sensor, which has high sensitivity (19 kPa^-1), ultralow detection limit (0.05 Pa), and ultrafast response (≤0.8 ms). Additionally, EMPA nanogenerators with high triboelectric and piezoelectric outputs achieve reliable biomechanical energy harvesting. The flexible self-assembly of EMPAs exhibits immense potential in superb individual healthcare and excellent human-machine interaction in an interference-free and comfortable manner.

All-Weather Freshwater and Electricity Simultaneous Generation by Coupled Solar Energy and Convection

Integrating solar evaporation-driven desalination and electricity production has emerged as a promising approach to alleviate energy crisis and freshwater scarcity. However, there remain huge challenges to achieve high water productivity and steady power generation efficiency. Herein, a compact evaporation-induced water-electricity co-generation device was proposed using a bio-waste squid ink sphere-based cellulose fabric as an evaporator and a silicon nanowires array-based evaporation-driven moist-electric generator. The efficient localized solar thermal heating of the photothermal component leads to significant enhancement in freshwater yield, and the latent heat of vapor condensation is recycled to promote the electricity generation. More notably, the device is capable of harvesting wind energy toward all-weather water and power generation. The fabricated device demonstrated a high evaporation rate of 2.17 kg m^-2 h^-1 with a collection rate of 66.7% and a maximum output voltage of 1.48 V under one sun illumination with a wind speed of 4 m s^-1. The outdoor experiments display a maximum water evaporation rate of 1.84 kg m^-2 h^-1 with a maximum output voltage of 1.35 V even on cloudy days. Such superior performance of a comprehensive device has great potential for sustainable and practical application in freshwater and electricity generation.

Polyaniline coated MOF-derived Mn2O3 nanorods for efficient hybrid capacitive deionization

Mn-based oxides are efficient pseudocapacitive electrode materials and have been investigated for capacitive deionization (CDI). However, their poor conductivity seriously affects their desalination performance. In this work, polyaniline coated Mn₂O₃ nanorods (PANI/Mn₂O₃) are synthesized by oxidizing a Mn-based metal organic framework (MOF) and subsequent in-situ chemical polymerization. The polyaniline not only acts as a conductive network for faradaic reactions of Mn₂O₃, but also enhances the desalination rate. PANI/Mn₂O₃ has a specific capacitance of 87 F g^-1 (at 1 A g^-1), superior to that of Mn₂O₃ nanorod (52 F g^-1 at 1 A g^-1). The hybrid CDI cell constructed with a PANI/Mn₂O₃ cathode and an active carbon anode shows a high desalination capacity of 21.6 mg g^-1, superior recyclability with only 11.3% desalination capacity decay after 30 desalination cycles and fast desalination rate of 2.2 mg g^-1 min^-1. PANI/Mn₂O₃ is a potential candidate for high performance CDI applications.

Integration of renewable energy in wastewater treatment during COVID-19 pandemic: Challenges, opportunities, and progressive research trends

SARS-CoV-2 has aroused drastic effects on the global economy and public health. In response to this, personal protective equipment, hand hygiene, and social distancing have been considered the most important ways to prevent the direct spread of the virus. SARS-CoV-2 would be possible survive in wastewater for a few days, leading to secondary transmission via contact with water and wastewater. Thus, the most economical and practical approaches for decentralized wastewater treatment are renewable energies such as the solar energy disinfestation process. However, as freshwater requirements increase and fossil fuels become unsustainable, renewable energy becomes more attractive for desalination applications. Solar photovoltaic, membrane-based, and electricity desalination technologies are becoming increasingly popular due to their lower energy requirements. Several aquatic environments could be benefitted from solar energy wastewater disinfection. Besides, utilizing solar energy during the day can inactivate SARS-CoV-2 to nearly 90%. However, conventional membrane-based desalination practices have also been integrated, including reverse osmosis (RO) and electrodialysis (ED). Several exciting membrane processes have been developed recently, including membrane distillation (MD), pressure-reduced osmosis (PRO), and reverse electrodialysis (RED). Such operations can produce clean and sustainable electricity from brine and impaired water, generally considered hazardous to the environment. As a result, neither PRO nor RED can produce electricity without mixing a high salinity solution (such as seawater or brine and wastewater, respectively) with a low salinity solution. Herein, we critically review the progress in applying renewable energy such as solar energy and geothermal energy for generating electricity from wastewater treatment and uniquely discuss the effects of these two types of renewable energy on SARS-CoV-2 in air and wastewater treatment. We also highlight the significant process made on the membrane processes utilizing renewable energy and research gaps from the standpoint of producing clean and sustainable energy. The significant points of this review are: (1) among various types of renewable energy, solar energy and geothermal energy have been predominantly studied for wastewater treatment, (2) effects of these two types of renewable energy on SARS-CoV-2 in air and wastewater treatment are critically analyzed, and (3) the knowledge gaps and anticipated future research outlook have been consequently proposed thereof.