Upconversion fluorescent strip sensor for rapid determination of Vibrio anguillarum

Functional Green-Emitting Mn2+-doped Zinc Germanate Persistent Luminescent Nanoparticles for Dual-Mode Immunochromatographic Detection

Immunochromatography is a commonly used immediate detection technique, using signal labels to generate detection signals for rapid medical diagnosis. However, its detection sensitivity is affected by background fluorescence caused by the excitation light source. We have developed an immunochromatographic test strip using Zn2GeO4:Mn2+ (ZGM) persistent luminescent nanoparticles (PLNPs) for immediate fluorescence detection and highly sensitive persistent luminescence (PersL) detection without background fluorescence interference. ZGM emits a strong green light when exposed to ultraviolet (UV) excitation, and its green PersL can persist for over 30 min after the excitation light is turned off. We modified the surface of ZGM with heparin-binding protein (HBP) antibodies to create immunochromatographic test strips for the detection of HBP as the target analyte. Under UV excitation, the chromatography test paper can be visually observed at concentrations as low as 25 ng/mL. After the excitation light source is switched off, PersL can achieve a detection limit of 4.7 ng/mL without background interference. This dual-mode immunochromatographic detection, based on ZGM, shows great potential for in vitro diagnostic applications.

Lateral flow assay of pathogenic viruses and bacteria in healthcare

Healthcare-associated pathogenic viruses and bacteria can have a serious impact on human health and have attracted widespread global attention. The lateral flow assay is a unidirectional detection based on the binding of a target analyte and a bioreceptor on the device via lateral flow. With incredible advantages over traditional chromatographic methods, such as rapid detection, ease of manufacture and cost effectiveness, these test strips are increasingly considered the ideal form for point-of-care applications. This review explores lateral flow assays for pathogenic viruses and bacteria, with a particular focus on methodologies, device components, construction methods, and applications. We anticipate that this review could provide exciting opportunities for developing new lateral flow devices for pathogens and advance related healthcare applications.

Active CRISPR-Cas12a on Hydrophilic Metal-Organic Frameworks: A Nanobiocomposite with High Stability and Activity for Nucleic Acid Detection

CRISPR-Cas12a is an accurate and responsive biosensing technique, but its limited stability has restricted its widespread applications. To address this, we propose a strategy using metal-organic frameworks (MOFs) to protect Cas12a from harsh environments. After screening multiple candidate MOFs, it was found that hydrophilic MAF-7 is highly compatible with Cas12a, and the as-formed Cas12a-on-MAF-7 (COM) not only retains high enzymatic activity but also possesses excellent tolerance to heat, salt, and organic solvents. Further investigation showed that COM can serve as an analytical component for nucleic acid detection, resulting in an ultrasensitive assay for SARS-CoV-2 RNA detection with a detection limit of 1 copy. This is the first successful attempt to create an active Cas12a nanobiocomposite that functions as a biosensor without the need for shell deconstruction or enzyme release.

Nanozyme-based colorimetric biosensor with a systemic quantification algorithm for noninvasive glucose monitoring

Diabetes mellitus accompanies an abnormally high glucose level in the bloodstream. Early diagnosis and proper glycemic management of blood glucose are essential to prevent further progression and complications. Biosensor-based colorimetric detection has progressed and shown potential in portable and inexpensive daily assessment of glucose levels because of its simplicity, low-cost, and convenient operation without sophisticated instrumentation. Colorimetric glucose biosensors commonly use natural enzymes that recognize glucose and chromophores that detect enzymatic reaction products. However, many natural enzymes have inherent defects, limiting their extensive application. Recently, nanozyme-based colorimetric detection has drawn attention due to its merits including high sensitivity, stability under strict reaction conditions, flexible structural design with low-cost materials, and adjustable catalytic activities. This review discusses various nanozyme materials, colorimetric analytic methods and mechanisms, recent machine learning based analytic methods, quantification systems, applications and future directions for monitoring and managing diabetes.

Advances in fluorescence sensing enabled by lanthanide-doped upconversion nanophosphors

Lanthanide-doped upconversion nanoparticles (UCNPs), characterized by converting low-energy excitation to high-energy emission, have attracted considerable interest due to their inherent advantages of large anti-Stokes shifts, sharp and narrow multicolor emissions, negligible autofluorescence background interference, and excellent chemical- and photo-stability. These features make them promising luminophores for sensing applications. In this review, we give a comprehensive overview of lanthanide-doped upconversion nanophosphors including the fundamental principle for the construction of UCNPs with efficient upconversion luminescence (UCL), followed by state-of-the-art strategies for the synthesis and surface modification of UCNPs, and finally describing current advances in the sensing application of upconversion-based probes for the quantitative analysis of various analytes including pH, ions, molecules, bacteria, reactive species, temperature, and pressure. In addition, emerging sensing applications like photodetection, velocimetry, electromagnetic field, and voltage sensing are highlighted.

Exploring the use of upconversion nanoparticles in chemical and biological sensors: from surface modifications to point-of-care devices

Upconversion nanoparticles (UCNPs) have emerged as promising luminescent nanomaterials due to their unique features that allow the overcoming of several problems associated with conventional fluorescent probes. Although UCNPs have been used in a broad range of applications, it is probably in the field of sensing where they best evidence their potential. UCNP-based sensors have been designed with high sensitivity and selectivity, for detection and quantification of multiple analytes ranging from metal ions to biomolecules. In this review, we deeply explore the use of UCNPs in sensing systems emphasizing the most relevant and recent studies on the topic and explaining how these platforms are constructed. Before diving into UCNP-based sensing platforms it is important to understand the unique characteristics of these nanoparticles, why they are attracting so much attention, and the most significant interactions occurring between UCNPs and additional probes. These points are covered over the first two sections of the article and then we explore the types of fluorescent responses, the possible analytes, and the UCNPs' integration with various material types such as gold nanostructures, quantum dots and dyes. All the topics are supported by analysis of recently reported sensors, focusing on how they are built, the materials' interactions, the involved synthesis and functionalization mechanisms, and the conjugation strategies. Finally, we explore the use of UCNPs in paper-based sensors and how these platforms are paving the way for the development of new point-of-care devices.

Gold Nanobeads with Enhanced Absorbance for Improved Sensitivity in Competitive Lateral Flow Immunoassays

BACKGROUND

Colloidal gold based lateral flow immunoassay (LFIA) commonly suffers from relatively low detection sensitivity due to the insufficient brightness of conventional gold nanoparticles (AuNPs) with the size of 20-40 nm.

METHODS

Herein, three kinds of gold nanobeads (GNBs) with the size of 94 nm, 129 nm, and 237 nm, were synthesized by encapsulating numerous hydrophobic AuNPs (10 nm) into polymer matrix. The synthesized GNBs exhibited the enhanced colorimetric signal intensity compared with 20-40 nm AuNPs. The effects of the size of GNBs on the sensitivity of LFIA with competitive format were assessed.

RESULTS

The results showed that the LFIA using 129 nm GNBs as amplified signal probes exhibits the best sensitivity for fumonisin B1 (FB1) detection with a cut-off limit (for visual qualitative detection) at 125 ng/mL, a half maximal inhibitory concentration at 11.27 ng/mL, and a detection limit at 1.76 ng/mL for detection of real corn samples, which are 8-, 3.82-, and 2.89-fold better than those of conventional AuNP40-based LFIA, respectively. The developed GNB-LFIA exhibited negligible cross-reactions with other common mycotoxins. In addition, the accuracy, precision, reliability, and practicability were demonstrated by determining real corn samples.

CONCLUSIONS

All in all, the proposed study provides a promising strategy to enhance the sensitivity of competitive LFIA via using the GNBs as amplified signal probes.

Ultrasensitive Point-of-Care Test for Tumor Marker in Human Saliva Based on Luminescence-Amplification Strategy of Lanthanide Nanoprobes

The point-of-care detection of tumor markers in saliva with high sensitivity and specificity remains a daunting challenge in biomedical research and clinical applications. Herein, a facile and ultrasensitive detection of tumor marker in saliva based on luminescence-amplification strategy of lanthanide nanoprobes is proposed. Eu2O3 nanocrystals are employed as bioprobes, which can be easily dissolved in acidic enhancer solution and transform into a large number of highly luminescent Eu3+ micelles. Meanwhile, disposable syringe filter equipped with nitrocellulose membrane is used as bioassay platform, which facilitates the accomplishment of detection process within 10 min. The rational integration of dissolution enhanced luminescent bioassay strategy and miniaturized detection device enables the unique lab-in-syringe assay of tumor marker like carcinoembryonic antigen (CEA, an important tumor marker in clinic diagnosis and prognosis of cancer) with a detection limit down to 1.47 pg mL-1 (7.35 × 10-15 m). Upon illumination with a portable UV flashlight, the photoluminescence intensity change above 0.1 ng mL-1 (0.5 × 10-12 m) of CEA can be visually detected by naked eyes, which allows one to qualitatively evaluate the CEA level. Moreover, we confirm the reliability of using the amplified luminescence of Eu2O3 nanoprobes for direct quantitation of CEA in patient saliva samples, thus validates the practicality of the proposed strategy for both clinical diagnosis and home self-monitoring of tumor marker in human saliva.

Tutorial: design and fabrication of nanoparticle-based lateral-flow immunoassays

Lateral-flow assays (LFAs) are quick, simple and cheap assays to analyze various samples at the point of care or in the field, making them one of the most widespread biosensors currently available. They have been successfully employed for the detection of a myriad of different targets (ranging from atoms up to whole cells) in all type of samples (including water, blood, foodstuff and environmental samples). Their operation relies on the capillary flow of the sample throughout a series of sequential pads, each with different functionalities aiming to generate a signal to indicate the absence/presence (and, in some cases, the concentration) of the analyte of interest. To have a user-friendly operation, their development requires the optimization of multiple, interconnected parameters that may overwhelm new developers. In this tutorial, we provide the readers with: (i) the basic knowledge to understand the principles governing an LFA and to take informed decisions during lateral flow strip design and fabrication, (ii) a roadmap for optimal LFA development independent of the specific application, (iii) a step-by-step example procedure for the assembly and operation of an LF strip for the detection of human IgG and (iv) an extensive troubleshooting section addressing the most frequent issues in designing, assembling and using LFAs. By changing only the receptors, the provided example procedure can easily be adapted for cost-efficient detection of a broad variety of targets.

Point-of-Need Diagnostics for Foodborne Pathogen Screening

Foodborne illness is a major public health issue that results in millions of global infections annually. The burden of such illness sits mostly with developing countries, as access to advanced laboratory equipment and skilled lab technicians, as well as consistent power sources, is limited and expensive. Current gold standards in foodborne pathogen screening involve labor-intensive sample enrichment steps, pathogen isolation and purification, and costly readout machinery. Overall, time to detection can take multiple days, excluding the time it takes to ship samples to off-site laboratories. Efforts have been made to simplify the workflow of such tests by integrating multiple steps of foodborne pathogen screening procedures into a singular device, as well as implementing more point-of-need readout methods. In this review, we explore recent advancements in developing point-of-need devices for foodborne pathogen screening. We discuss the detection of surface markers, nucleic acids, and metabolic products using both paper-based and microfluidic devices, focusing primarily on developments that have been made between 2015 and mid-2020.

Simultaneous and accurate visual identification of chicken, duck and pork components with the molecular amplification integrated lateral flow strip

We propose a visual strategy for simultaneous detection of multiple adulterated components in beef by integration of multiple polymerase chain reaction (mPCR) with the lateral flow strip (LFS). The primer sets for adulterated components are uniquely designed with different nucleic acid tags (NAT), enabling the amplicons with specific wobbled sequences at two opposite ends. The wobbled sequences will precisely hybridize with the pre-immobilized capture probes on T lines (T1, T2 and T3) and C line, contributing to the coloration of LFS. Taking advantages of extraordinary amplification efficiency of PCR and simplicity of LFS, common adulterated components including chicken, duck and pork can be easily detected with LOD as low as 0.01% (wt%), which is comparable to that of quantitative real-time polymerase chain reaction (qPCR) but with more simplified operations and reduced costs. The method can be extended to identification of other components by replacing the functional primer set. This method can be a useful candidate for meat quality control at the resource-limited setups.

Metal-polydopamine framework based lateral flow assay for high sensitive detection of tetracycline in food samples

Gold nanoparticles (AuNPs)-based lateral flow assay (LFA) enables a rapid detection of tetracycline (TET) in food samples but suffers from low sensitivity. Herein, metal-polydopamine framework (MPF), as a label, was employed to load monoclonal antibodies (mAbs) directly as the probe in LFA for highly sensitive sensing of TET. Combining zeolitic imidazolate framework (ZIF-67) and polydopamine (PDA), a stable MPF with large size, well water-dispersible, excellent affinity and optical properties was prepared through a versatile layer-by-layer assembly (LLA) strategy. Under optimized conditions, the biosensor (MPF-LFA) exhibited a great linear relationship in the range of 0.09-6 ng/mL and a detection limit of 0.045 ng/mL for TET detection, which was over 66-fold more sensitive than traditional AuNPs based LFA. Furthermore, the MPF-LFA was successfully applied to the screening of TET in fish, chicken, milk and shrimp samples with satisfied recoveries from 91% to 114%.

Recent methods and biosensors for foodborne pathogen detection in fish: progress and future prospects to sustainable aquaculture systems

The aquaculture industry has advanced toward sustainable recirculating systems, in where parameters of food quality are strictly monitored. Despite that, as in the case of conventional aquaculture practices, the recirculating systems also suffer threats from Aeromonas spp., Vibrio spp., Streptococcus spp., among other foodborne pathogens infecting farmed fish. The aquaculture pathogens are routinely detected by conventional PCR methods or antibody-based tests, with the detection protocols confined to laboratory use. Emerging assay technologies and biosensors recently reported in the literature open new opportunities to the development of sensitive, specific, and portable analytical devices to use in the field. Techniques of DNA/RNA analysis, immunoassays and other nanomolecular technologies have been facing important advances in response time, sensitivity, and enhanced power of discrimination among and within species. Moreover, the recent developments of electrochemical and optical signal transduction have facilitated the incorporation of the innovative assays to practical miniaturized devices. In this work, it is provided a critical review over foodborne pathogen detection by existing and promising methods and biosensors applied to fish samples and extended to other food matrices. While isothermal DNA/RNA amplification methods can be highlighted among the assay methods for their promising analytical performance and suitability for point-of-care testing, the electrochemical transduction provides a way to achieve cost-effective biosensors amenable to use in the aquaculture field. The adoption of new methods and biosensors would constitute a step forward in securing sustainable aquaculture systems.

Lateral flow immunostrips for the sensitive and rapid determination of 8-hydroxy-2'-deoxyguanosine using upconversion nanoparticles

Lateral flow immunostrips were newly designed and a sensitive and rapid fluorometric method for the determination of 8-hydroxy-2'-deoxyguanosine (8-OHdG) as a model target of small biomarker molecules was developed. The upconversion nanoparticles (UCNPs, NaYF4:Yb/Er core, and polyacrylic acid (PAA)-modified shell, size ~ 39 nm, excitation wavelength = 980 nm; emission wavelength = 540 nm) were employed as fluorescence signal material. The 8-OHdG antibody (Ab) was taken as the recognition probe while UCNP-labeled Ab was taken as the signal probe. Bovine serum albumin (BSA) was designed as carrier protein for 8-OHdG to form 8-OHdG-BSA conjugate as the capture probe. The lateral flow immunostrips were prepared by laminating a sample pad (glass fiber membrane), a test pad (nitrocellulose membrane), and adsorption pad (filter paper) on PVP backing. The capture probe was immobilized on the test zone while an IgG antibody taken as the control probe was immobilized on the control zone. When the signal probe and the sample were in sequence loaded on the sample pad, 8-OHdG analyte bound with the signal probe, and then the excess of the signal probe move along the strip and is collected by the capture probe on the test zone while the remnant signal probe is collected by the control probe on the control zone. The signal probe and capture probe were synthesized and characterized. The fluorescence intensity on the test zone was inversely proportional to the concentration of 8-OHdG for the quantitative determination while the fluorescence emission on the control zone was observed to validate the assay. The developed method showed a wide linear range from 0.10 to 10 nM, a quite low detection limit of 0.05 nM, small sample volume requirement (100 μL), short assay time (15 min), and good method reproducibility (RSD = 4.4%, nine immunostrips). Graphical abstract Schematic illustration of the configuration and measurement principle of lateral flow fluorescence immunostrip for 8-OHdG: (a) configuration; (b) preparation: load of capture probe (BSA-8-OHdG, 2 μL) on test zone; load of control probe (IgG Ab, 2 μL) on control zone; load of signal probe (UCNP-Ab, 16 μL) on sample pad; (c) measurement: load of sample (8-OHdG, 100 μL) on sample pad, collection, and measurement.

Signal amplification and quantification on lateral flow assays by laser excitation of plasmonic nanomaterials

Lateral flow assay (LFA) has become one of the most widely used point-of-care diagnostic methods due to its simplicity and low cost. While easy to use, LFA suffers from its low sensitivity and poor quantification, which largely limits its applications for early disease diagnosis and requires further testing to eliminate false-negative results. Over the past decade, signal enhancement strategies that took advantage of the laser excitation of plasmonic nanomaterials have pushed down the detection limit and enabled quantification of analytes. Significantly, these methods amplify the signal based on the current LFA design without modification. This review highlights these strategies of signal enhancement for LFA including surface enhanced Raman scattering (SERS), photothermal and photoacoustic methods. Perspectives on the rational design of the reader systems are provided. Future translation of the research toward clinical applications is also discussed.

A label-free protamine-assisted colorimetric sensor for highly sensitive detection of S1 nuclease activity

A label-free, simple and rapid colorimetric method for the sensitive detection of S1 nuclease activity based on protamine-assisted aggregation of gold nanoparticles.

Facile synthesis of sub-10 nm-sized bright red-emitting upconversion nanophosphors via tetrahedral YOF:Yb,Er seed-mediated growth

Ultrasmall and uniform tetrahedral-shaped YOF:Yb,Er upconversion nanophosphors (UCNs) are synthesized and sub-10 nm YOF:Yb,Er/YOF core/shell UCNs are formed via YOF:Yb,Er seed-mediated synthesis. The ultrasmall YOF:Yb,Er/YOF core/shell UCNs realize intense red emission under near infrared light (λ_ex = 980 nm).

Simultaneous Sensing of Seven Pathogenic Bacteria by Guanidine-Functionalized Upconversion Fluorescent Nanoparticles

The method capable of simultaneously detecting multiple target bacterial pathogens is necessary and of great interest. In this research, we demonstrated our initial effort to simultaneously detect seven common foodborne bacteria by developing a straightforward upconversion fluorescence sensing approach. The fluorescent nanosensor was constructed from a designed guanidine-functionalized upconversion fluorescent nanoparticles (UCNPs@GDN), tannic acid, and hydrogen peroxide (HP) and could quantify pathogenic bacteria in a nonspecific manner because the luminescence of the upconversion fluorescent nanoparticle was effectively strengthened in the presence of bacteria. When the developed nanosensor was applied to quantify multiple bacteria including Escherichia coli, Salmonella, Cronobacter sakazakii, Shigella flexneri, Vibrio parahaemolyticus, Staphylococcus aureus, and Listeria monocytogenes, a linear range of 10³ to 10⁸ cfu mL^-1 and a detection limit of 1.30 × 10² cfu mL^-1 have been obtained for the seven model mixture bacteria. In addition, the similar linear range and detection limit were also obtained for the detection of single bacteria. The present approach also exhibited acceptable recovery values ranging from 70.0 to 118.2% for bacteria in real samples (water, milk, and beef). All these results suggested that the guanidine-functionalized upconversion fluorescent nanosensor could be considered as a promising candidate for the rapid detection and surveillance of microbial pollutants in food and water.

Detection platforms for point-of-care testing based on colorimetric, luminescent and magnetic assays: A review

Along with the considerable potential and increasing demand of the point-of-care testing (POCT), corresponding detection platforms have attracted great interest in both academic and practical fields. The first few generations of conventional detection devices tend to be costly, complicated to operate and hard to move on account of early limitations in the level of technological development and relatively high requirement of performance. Owing to the requirements for rapidity, simplicity, accuracy and cost controlling in the POCT, reader systems are urgently needed to be developed, upgraded and modified constantly, realizing on-site testing and healthcare management without a specific place or cumbersome operation. Accordingly, numerous rapid detection platforms with diverse size and performance have emerged such as bench-top apparatuses, handheld devices and intelligent detection devices. This review discusses various devices developed mainly for the detection of lateral flow test strips (LFTSs) or microfluidic strips in the POCT and summarizes these devices by size and portability. Furthermore, on the basis of various detection methods and diverse probes usually containing specific nanoparticles composites, three most common aspects of detection rationale in the POCT are selected to elaborate each kind of detection platforms in this paper: colorimetric assay, luminescent detection and magnetic signal detection. Herein, we focus on their structures, detection mechanisms and assay results, accompany with discussions and comments on the performances, costs and potential application, as well as advantages and limitations of each technique. In addition, perspectives on the future advances of detection platforms and some conclusions are proposed.

Up-Converting Nanoparticle-Based Immunochromatographic Strip for Multi-Residue Detection of Three Organophosphorus Pesticides in Food

Organophosphorus (OP) pesticides are widely used to control pests because of their high activity. This study described a rapid and sensitive lateral flow immunochromatographic (LFIC) assay based on up-converting nanoparticles (UCNPs) for multi-residue detection of three OP pesticides. The developed assay integrated novel fluorescent material UCNPs labeled with a broad-specific monoclonal antibody. Based on the competitive platform by immobilized antigen in the test zone, the optimized UCNPs-LFIC assay enabled sensitive detection for parathion, parathion-methyl, and fenitrothion with IC50 of 3.44, 3.98, and 12.49 ng/mL (R 2 ≥ 0.9776) within 40 min. The detectable ability ranged from 0.98 to 250 ng/mL. There was no cross-reactivity with fenthion, phoxim, isocarbophos, chlorpyrifos, or triazophos, even at a high concentration of 500 ng/mL. Matrix interference from various agricultural products was also studied in food sample detection. In the spiked test, recoveries of the three OP pesticides ranged from 67 to 120% and relative standard deviations were below 19.54%. These results indicated that the proposed strip assay can be an alternative screening tool for rapid detection of the three OP pesticides in food samples.

Inorganic Complexes and Metal-Based Nanomaterials for Infectious Disease Diagnostics

Infectious diseases claim millions of lives each year. Robust and accurate diagnostics are essential tools for identifying those who are at risk and in need of treatment in low-resource settings. Inorganic complexes and metal-based nanomaterials continue to drive the development of diagnostic platforms and strategies that enable infectious disease detection in low-resource settings. In this review, we highlight works from the past 20 years in which inorganic chemistry and nanotechnology were implemented in each of the core components that make up a diagnostic test. First, we present how inorganic biomarkers and their properties are leveraged for infectious disease detection. In the following section, we detail metal-based technologies that have been employed for sample preparation and biomarker isolation from sample matrices. We then describe how inorganic- and nanomaterial-based probes have been utilized in point-of-care diagnostics for signal generation. The following section discusses instrumentation for signal readout in resource-limited settings. Next, we highlight the detection of nucleic acids at the point of care as an emerging application of inorganic chemistry. Lastly, we consider the challenges that remain for translation of the aforementioned diagnostic platforms to low-resource settings.

Ultrasensitive detection of Sudan I in food samples by a quantitative immunochromatographic assay

An immunochromatographic assay (ICA) based on surface-enhanced Raman scattering (SERS) for ultrasensitive determination of Sudan I in food samples was reported. Gold-silver core-shell bimetallic nanorods (referred to as Au@Ag NRs) were synthesized, characterized and used as the substrate for preparation of the ICA. Polyclonal antibody against Sudan I was immobilized on the surface of the Au@Ag NRs carrying the Raman reporter 5,5'-dithiobis (2-nitrobenzoic acid). The Raman scattering intensity on the test line was used for quantitation of Sudan I. The assay was completed in 15 min. IC₅₀ and limit of detection (LOD) were 30 pg mL^-1 and 0.2 pg mL^-1, respectively. There was no cross-reactivity (CR) of the assay with Sunset Yellow, Lemon Yellow and Brilliant blue FCF, but only 3.53%-9.74% CR with Sudan II, III and IV. The recoveries of Sudan I from spiked food samples were in the range of 88.9-107.6% with relative standard deviation of 3.7-8.7% (n = 3).

Functionalized reduced graphene oxide as a lateral flow immuneassay label for one-step detection of Escherichia coli O157:H7

In this study, graphene oxide (GO) and reduced graphene oxide (rGO) were used as visual labels in a lateral flow assay for detection of E. coli O157:H7. The color intensity was employed for the quantitative measurements of the target bacteria. Quantitative results showed that in comparison to GO, rGO can provide higher color intensity owing to enhanced light absorption following chemical reduction. Our results confirm that the visual limit of detection of the target bacteria by rGO is ∼10⁵ colony forming unit per milliliter (CFU/ml), which closely compares with current alternative techniques using gold nanoparticles. The performance and practicability of the rGO-based test strips for detection of the target bacteria in milk and drinking water were validated with conventional plating and colony counting techniques. Results suggest that the proposed lateral flow assay is sensitive, specific, and affordable. It has also the potential to become a widely used detection technique for E. coli O157:H7 and a wide variety of other analytes.

A test strip for ochratoxin A based on the use of aptamer-modified fluorescence upconversion nanoparticles

An aptamer-based test strip is described for visual and instrumental determination of the mycotoxin ochratoxin A (OTA). It is based on the use of NaYF₄:Yb,Er upconversion nanoparticles (UCNPs) as a label for the aptamer and on the competition between OTA and its complementary sequence for an OTA-specific aptamer. To improve the analytical performance, the optical properties of the UCNPs, the fluidity of the UCNP-aptamer conjugate, and the migration rate on the nitrocellulose membranes were investigated. Under the optimal experimental conditions and by using a 980-nm laser, the relative fluorescence intensity (test line value/control line value) is proportional to the logarithm of the OTA concentration over a range from 5 to 100 ng·mL^-1 (R² = 0.9955). The limit of the detection is 1.86 ng·mL^-1. This aptamer based flow assay can be performed within 15 min and has no serious cross-sensitivity to potentially interfering species. It was successfully applied to the determination of OTA in spiked wheat and beer samples. Graphical abstract An aptamer-based upconversion fluorescent strip based on the use of NaYF₄:Yb,Er nanoparticles was developed for sensitive detection of Ochratoxin A. The limit of the detection was determined as 1.86 ng·mL^-1. The assay can be performed within 15 min, indicating its great potential in point-of-care testing.

Paper-based biodetection using luminescent nanoparticles

Point-of-care and in-field technologies for rapid, sensitive and selective detection of molecular biomarkers have attracted much interest. Rugged bioassay technology capable of fast detection of markers for pathogens and genetic diseases would in particular impact the quality of health care in the developing world, but would also make possible more extensive screening in developed countries to tackle problems such as those associated with water and food quality, and tracking of infectious organisms in hospitals and clinics. Literature trends indicate an increasing interest in the use of nanomaterials, and in particular luminescent nanoparticles, for assay development. These materials may offer attributes for development of assays and sensors that could achieve improvements in analytical figures of merit, and provide practical advantages in sensitivity and stability. There is opportunity for cost-efficiency and technical simplicity by implementation of luminescent nanomaterials as the basis for transduction technology, when combined with the use of paper substrates, and the ubiquitous availability of cell phone cameras and associated infrastructure for optical detection and transmission of results. Luminescent nanoparticles have been described for a broad range of bioanalytical targets including small molecules, oligonucleotides, peptides, proteins, saccharides and whole cells (e.g., cancer diagnostics). The luminescent nanomaterials that are described herein for paper-based bioassays include metal nanoparticles, quantum dots and lanthanide-doped nanocrystals. These nanomaterials often have broad and strong absorption and narrow emission bands that improve opportunity for multiplexed analysis, and can be designed to provide emission at wavelengths that are efficiently processed by conventional digital cameras. Luminescent nanoparticles can be embedded in paper substrates that are designed to direct fluid flow, and the resulting combination of technologies can offer competitive analytical performance at relatively low cost.

A nitrocellulose membrane-based integrated microfluidic system for bacterial detection utilizing magnetic-composite membrane microdevices and bacteria-specific aptamers

Bacteria such as Acinetobacter baumannii (AB) can cause serious infections, resulting in high mortality if not diagnosed early and treated properly; there is consequently a need for rapid and accurate detection of this bacterial species. Therefore, we developed a new, nitrocellulose-based microfluidic system featuring AB-specific aptamers capable of automating the bacterial detection process via the activity of microfluidic devices composed of magnetic-composite membranes. Electromagnets were used to actuate these microfluidic devices such that the entire diagnostic process could be conducted in the integrated microfluidic system within 40 minutes with a limit of detection as low as 450 CFU per reaction for AB. Aptamers were used to capture AB in complex samples on nitrocellulose membranes, and a simple colorimetric assay was used to estimate bacterial loads. Given the ease of use, portability, and sensitivity of this aptamer-based microfluidic system, it may hold great promise for point-of-care diagnostics.

Effective Bioactivity Retention of Low-Concentration Antibodies on HFBI-Modified Fluorescence ICTS for Sensitive and Rapid Detection of PSA

Nowadays, increasing analytical sensitivity is still a big challenge in constructing membrane-based fluorescence immunochromatography test strips (FICTS). However, the bioactivity of antibody (Ab) immobilized on the test line (T line) of porous nitrocellulose membrane (PNM), which directly influences the analytical sensitivity, is less studied. In this work, a novel amphiphilic hydrophobin (HFBI) protein was introduced to modify the T line to effectively retain the Abs' bioactivity. The results indicated that HFBI could self-assemble on the PNM and immobilize the Abs in the "stand-up" orientation. Compared with the conventional FICTS, the HFBI-modified FICTS with only 0.2 mg/mL of monoclonal Abs on T line enable more accurate quantitative detection and better sensitivity (0.06 ng/mL for prostate specific antigen), which is more than 2 orders of magnitude lower than that of the conventional FICTS with the same concentration of monoclonal Abs on T line. Furthermore, the accuracy of this HFBI-modified FICTS was investigated by testing 150 clinical serum samples and the detection results were coincident with those by electrochemiluminescence immunoassay. Our results provide a novel and promising strategy of Ab immobilization on FICTS for near-patient and point-of-care application.

Fluorescein Isothiocyanate Labeling Antigen-Based Immunoassay Strip for Rapid Detection of Acidovorax citrulli

A simple and fast immunoassay strip to detect Acidovorax citrulli (Ac) using fluorescein isothiocyanate as a marker was developed. Fluorescein isothiocyanate (FITC) was added to sample culture medium for bacteria incubation, and the bacteria could emit a yellow-green fluorescence under ultraviolet light and become a fluorescent probe. This immunofluorescence strip (IFS) was based on the binding between fluorescent bacteria and the unlabeled monoclonal antibody (McAb) immobilized on the test area in nitrocellulose membrane. The detection limit of the strip was 10⁶ CFU/ml with a result that could be observed within 10 min. The IFS could detect eight strains of Ac and display no cross-reactions with 30 other pathogenic strains. The detection results would not be affected by impurities in plant or unknown microorganisms in natural field samples and were consistent with PCR results, indicating that the IFS has high accuracy. This is the first report of using only one unlabeled McAb to develop a direct-type immunofluorescence strip for the rapid detection of Ac. The IFS reduced detection time and simplified operation procedures compared with the traditional enzyme-linked immunosorbent assay (ELISA) and PCR methods. In addition, this simple and inexpensive method will play a significant role in monitoring plant pathogens on field detection.

Sensors and bioassays powered by upconverting materials

In recent years, considerable efforts have been done to better understand the peculiar emission properties of upconverting materials due to their widespread applications in different and important technological fields such as upconversion-based photoactivated cancer therapies, photoactivated drug-delivery, magnetic resonance imaging contrast agents, bioimaging. However, one of the most promising applications of upconverting materials concerns the field of sensing, due to their unique emission properties. In fact, the minimal autofluorescence, blinking, photo-bleaching, and high photostability makes them an excellent alternative to organic dyes or quantum dots. This article reviews the state-of-the-art, design, and sensing strategies of upconversion-based sensing platforms, with special attention to upconverting nanoparticles, as well as how the incorporation of these materials into pre-existing diagnostic tests and bioassays have improved their capabilities for the detection of different kinds of analytes.

Mechanochemically prepared SrFCl nanophosphor co-doped with Yb3+ and Er3+ for detecting ionizing radiation by upconversion luminescence

We report a novel method for detecting ionizing radiation by employing the phenomenon of upconversion luminescence. Nanocrystalline SrFCl:Yb³⁺/Er³⁺ was prepared by ball-milling and characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The photoluminescence properties of nanocrystalline SrFCl:Yb³⁺, SrFCl:Er³⁺ and SrFCl:Yb³⁺/Er³⁺ before and after X-irradiation were investigated. The results demonstrate that both Yb³⁺ and Er³⁺ ions in the SrFCl host are reduced to their divalent state upon X-ray exposure. Under 980 nm infrared excitation, SrFCl:Yb³⁺/Er³⁺ nanocrystals displayed efficient upconversion luminescence. The upconversion luminescence intensity gradually decreased with increasing X-irradiation in a double exponential fashion with rate constants of k₁ = 0.08 Gy^-1 and k₂ = 0.01 Gy^-1. In comparison with other X-ray storage phosphors, the present system shows a much higher stability of stored information since it is not subject to photobleaching in the read-out process. This is the first report on detecting ionizing radiation by upconversion luminescence, with the potential for improved read-out performance over traditional storage phosphors. Possible applications of the present phosphor include bioimaging and in vivo cell-level X-ray dose monitoring.

Clickable Multifunctional Dumbbell Particles for in Situ Multiplex Single-Cell Cytokine Detection

We report a novel strategy for fabrication of multifunctional dumbbell particles (DPs) through click chemistry for monitoring single-cell cytokine releasing. Two different types of DPs were prepared on a large scale through covalent bioorthogonal reaction between methyltetrazine and trans-cyclooctene on a microchip under a magnetic field. After collection of the DPs, the two sides of each particle were further functionalized with different antibodies for cell capturing and cytokine detection, respectively. These DPs labeled with different fluorescent dyes have been used for multiplex detection and analysis of cytokines secreted by single live cells. Our results show that this new type of DPs are promising for applications in cell sorting, bioimaging, single-cell analysis, and biomedical diagnostics.

Household Fluorescent Lateral Flow Strip Platform for Sensitive and Quantitative Prognosis of Heart Failure Using Dual-Color Upconversion Nanoparticles

Heart failure (HF) is the end-stage of cardiovascular diseases, which is associated with a high mortality rate and high readmission rate. Household early diagnosis and real-time prognosis of HF at bedside are of significant importance. Here, we developed a highly sensitive and quantitative household prognosis platform (termed as UC-LFS platform), integrating a smartphone-based reader with multiplexed upconversion fluorescent lateral flow strip (LFS). Dual-color core-shell upconversion nanoparticles (UCNPs) were synthesized as probes for simultaneously quantifying two target antigens associated with HF, i.e., brain natriuretic peptide (BNP) and suppression of tumorigenicity 2 (ST2). With the fluorescent LFS, we achieved the specific detection of BNP and ST2 antigens in spiked samples with detection limits of 5 pg/mL and 1 ng/mL, respectively, both of which are of one order lower than their clinical cutoff. Subsequently, a smartphone-based portable reader and an analysis app were developed, which could rapidly quantify the result and share prognosis results with doctors. To confirm the usage of UC-LFS platform for clinical samples, we detected 38 clinical serum samples using the platform and successfully detected the minimal concentration of 29.92 ng/mL for ST2 and 17.46 pg/mL for BNP in these clinical samples. Comparing the detection results from FDA approved clinical methods, we obtained a good linear correlation, indicating the practical reliability and stability of our developed UC-LFS platform. Therefore, the developed UC-LFS platform is demonstrated to be highly sensitive and specific for sample-to-answer prognosis of HF, which holds great potential for risk assessment and health monitoring of post-treatment patients at home.

NIR upconversion fluorescence glucose sensing and glucose-responsive insulin release of carbon dot-immobilized hybrid microgels at physiological pH

This work reports the preparation of multifunctional hybrid microgels based on the one-pot free radical dispersion polymerization of hydrogen-bonding complexes in water, formed from hydroxyl/carboxyl bearing carbon dots with 4-vinylphenylboronic acid and acrylamide comonomers, which can realize the simultaneous optical detection of glucose using near infrared light and glucose-responsive insulin delivery.

A review of fluorescent signal-based lateral flow immunochromatographic strips

Fluorescent signal-based lateral flow immunochromatographic strips (FLFICS) have received great expectations since they combine the quantitative sensitivity of fluorescence analysis and the simplicity, rapidness, and portability of a common lateral flow immunochromatographic strip (LFICS).

Graphene oxide and carboxylated graphene oxide: Viable two-dimensional nanolabels for lateral flow immunoassays

Graphene oxide (GO) and carboxylated GO were used as labels for lateral flow immunoassays, instead of the conventionally used colloidal gold and colored latex labels. A sensor is demonstrated that enables fast screening for aflatoxin B₁ (AFB₁) as a model analyte using the antibody-GO complex as the recognition element. The visual limit of detection and cut-off value for AFB₁ are 0.3 and 1ng/mL, respectively. It is shown that GO and carboxylated GO are viable black labels for use in lateral flow assays, one typical advantage being the saving cost (compared to the use of colloidal gold). Qualitative results are achieved within 15min, and the analytical results were in good agreement with the reference LC MS/MS method. The method was successfully applied to the on-site determination of AFB₁ in agricultural products. In our perception, it opens new possibilities for the screening of other toxins by lateral flow immunoassays using GO and carboxylated GO as labels.

Effect of different-sized spherical gold nanoparticles grown layer by layer on the sensitivity of an immunochromatographic assay

Effect of different-sized spherical gold nanoparticles grown layer by layer on the sensitivity of immunochromatographic assay.

A SERS-based lateral flow assay biosensor for highly sensitive detection of HIV-1 DNA

User-friendly lateral flow (LF) strips have been extensively used for point-of-care (POC) self-diagnostics, but they have some limitations in their detection sensitivity and quantitative analysis because they only identify the high cut-off value of a biomarker by utilizing color changes that are detected with the naked eye. To resolve these problems associated with LF strips, we developed a novel surface-enhanced Raman scattering (SERS)-based LF assay for the quantitative analysis of a specific biomarker in the low concentration range. Herein, human immunodeficiency virus type 1 (HIV-1) DNA was chosen as the specific biomarker. Raman reporter-labeled gold nanoparticles (AuNPs) were employed as SERS nano tags for targeting and detecting the HIV-1 DNA marker, as opposed to using bare AuNPs in LF strips. It was possible to quantitatively analyze HIV-1 DNA with high sensitivity by monitoring the characteristic Raman peak intensity of the DNA-conjugated AuNPs. Under optimized conditions, the detection limit of our SERS-based lateral flow assay was 0.24 pg/mL, which was at least 1000 times more sensitive compared to colorimetric or fluorescent detection methods. These results demonstrate the potential feasibility of the proposed SERS-based lateral flow assay to quantitatively detect a broad range of genetic diseases with high sensitivity.