Single cell oil of oleaginous fungi from the tropical mangrove wetlands as a potential feedstock for biodiesel

One-pot bioconversion of fungal lipid to mycodiesel: a sustainable approach

The conversion of filamentous fungus-based feedstock into Biodiesel holds potential as a sustainable and eco-conscious method for producing alternative liquid fuels. This study examined the comparison of individual Fatty Acid Methyl Esters (FAME) of Aspergillus niger and Curvularia lunata with the consortium of both filamentous fungal cocktail Fatty acid methyl esters (cFAME), following a transesterification process that turned the fungal lipids into myco-based biodiesel productions. cFAME weighs 23.89 g and accumulates to 20.43 g of lipid yield, with 86% of cellular lipids; in contrast, A. niger weighs 12.65 g and pile up 9.5 g of lipid yield, with 75% of cellular lipid, also C. lunata exhibits 8.35 g of dry weight with 4.89 g of lipid concentration, with 59% of cellular lipids. A. niger was known to contain C16-C18 saturated and unsaturated fatty acids possess LAME (C18:2), OAFA (C18:1), and PAME (C16:0) were shown in high percentages accounted for 86.6% in A. niger. The results showed that PUFA was predominant over MUFA and SFA. C. lunata chiefly produces C16 and C18 fatty acids, which are considered favorable for combustion properties with oleic acid (C18:1), linoleic acid (C18:2), palmitic acid (C16:0), and stearic acid (C18:0), on the comparison. However, the FAME profile of C. lunata occupies only 39.07% of the biodiesel quality. Pentadecanoic acid, palmitic acid, palmitoleic acid, Oleic acid, Linolenic acid, Linoleic acis, and Hexanoic acid with the carbon range of C6:0 - C18:3 were observed in cFAME. Based on the biodiesel yield, cFAME scored 20.55%, whereas A. niger with 11.05 and C.lunata 2.45%, respectively. The presence of methyl esters containing various long-chain fatty acids indicates very effective biodiesel assets, as confirmed by GC-MS analysis, which evidenced ignition efficiency, among others. cFAMEs were impacted by high ignition efficiency with > 4 min. Consortium strategies seize attention in different dimensions and have been confirmed by their upregulation in their fatty acid profiles; in the future, the combination of high lipid holders among the fungal kingdom can be an alternative in myco-based biodiesel production.

Aspergillus terreus variant TB21 wet biomass optimized by in-situ transesterification for biodiesel production

The oleaginous fungus, Aspergillus terreus when subjected to random chemical mutagenesis led to isolation of TB21 variant with improved lipid content (78.1%) as compared to wild type (49.8%). The fungal wet biomass grown on sugarcane bagasse hydrolysate (SCBH) was subjected to one-step in-situ (direct) acid transesterification to optimize its conversion to biodiesel using a 2-level factorial statistical design of experiments. The process optimization revealed that wet biomass and methanol were the most significant factors and in a short reaction time period of 5 min with low methanol: wet biomass ratio (10:1) influenced FAME production Statistical optimization studies showed that TB21 exhibited a higher FAME content of 76.5 and 38.1% (w/w) from wet and dry biomass, respectively when compared to wild type (48.1 and 24.5%). FAME productivity (0.55-1 h-1) and a yield (66 gL-1) were achieved when TB21 was grown on SCBH for 120 h at 30 °C. The FAME profile from the wet biomass of TB21 grown on SCBH had desirable amounts of saturated (77.7%), monounsaturated (7.2%), and polyunsaturated (2.4%) methyl esters. Physico-chemical properties of TB21-derived biodiesel were determined, namely, density(0.88 g cm-3), kinematic viscosity (4.1 mm s-2), iodine value (96.82), cetane number (55.31), free fatty acid content (0.15%), total acid number (0.3 NaOH mg g-1), meeting international (ASTM D6751, EN 14214) and Indian (IS 15607) standards. Thus, the direct one-pot in situ transesterification reaction using wet biomass of variant TB21 strain showed improved production and quality of biodiesel with potential large scale application using the low-cost substrate (SCBH).

Application of microbial resources in biorefineries: Current trend and future prospects

The recent growing interest in sustainable and alternative sources of energy and bio-based products has driven the paradigm shift to an integrated model termed "biorefinery." Biorefinery framework implements the concepts of novel eco-technologies and eco-efficient processes for the sustainable production of energy and value-added biomolecules. The utilization of microbial resources for the production of various value-added products has been documented in the literatures. However, the appointment of these microbial resources in integrated resource management requires a better understanding of their status. The main of aim of this review is to provide an overview on the defined positioning and overall contribution of the microbial resources, i.e., algae, fungi and bacteria, for various bioprocesses and generation of multiple products from a single biorefinery. By utilizing waste material as a feedstock, biofuels can be generated by microalgae while sequestering environmental carbon and producing value added compounds as by-products. In parallel, fungal biorefineries are prolific producers of lignocellulose degrading enzymes along with pharmaceutically important novel products. Conversely, bacterial biorefineries emerge as a preferred platform for the transformation of standard cells into proficient bio-factories, developing chassis and turbo cells for enhanced target compound production. This comprehensive review is poised to offer an intricate exploration of the current trends, obstacles, and prospective pathways of microbial biorefineries, for the development of future biorefineries.

Unveiling the anticancer potentiality of single cell oils produced by marine oleaginous Paradendryphiella sp. under optimized economic growth conditions

Bioprospecting about new marine oleaginous fungi that produce advantageous bioproducts in a green sustainable process is the key of blue bioeconomy. Herein, the marine Paradendryphiella sp. was utilized for single cell oils (SCOs) production economically, via central composite design, the lipid content enhanced 2.2-fold by 5.5 g/L lipid yeild on seawater-based media supplemented with molasses concentration 50 g/L, yeast extract, 2.25 g/L at initial pH value (5.3) and 8 days of static incubation. Subsequently, the fatty acid methyl esters profiles of SCOs produced on optimized media under different abiotic conditions were determined; signifying qualitative and quantitative variations. Interestingly, the psychrophilic-prolonged incubation increased the unsaturation level of fatty acids to 59.34%, while ω-6 and ω-3 contents representing 23.53% and 0.67% respectively. Remarkably, it exhibited the highest EC100 dose by 677.03 µg/mL on normal human lung fibroblast Wi-38 cells. Meanwhile, it showed the highest inhibiting proliferation potential on cancer cell lines of A549, MDA-MB 231 and HepG-2 cells by 372.37, 417.48 and 365.00 µg/mL, respectively. Besides, it elevated the oxidative stress, the expression of key apoptotic genes and suppressed the expression of key oncogenes (NF-κB, BCL2 and cyclin D); implying its promising efficacy in cancer treatment as adjuvant drug. This study denoted the lipogenesis capacity of Paradendryphiella sp. under acidic/alkaline and psychrophilic/mesophilic conditions. Hereby attaining efficient and economic process under seasonal variation with different Egyptian marine sources to fill the gap of freshwater crisis and simultaneously preserve energy.

Use of Microorganisms as Nutritional and Functional Feedstuffs for Nursery Pigs and Broilers

The objectives of this review paper are to introduce the structures and composition of various microorganisms, to show some applications of single cells as alternative protein supplements or energy feeds in swine and poultry diets, and to discuss the functional effects of microorganisms as feed additives on the growth performance and intestinal health of nursery pigs and broilers. Microorganisms, including bacteria, yeasts, and microalgae, have been commonly supplemented in animal diets because they are cost-effective, stable, and have quantitative production that provides nutritional and functional benefits to pigs and broilers. Microorganisms could be alternative antibiotics to enhance intestinal health due to bioactive components from cell wall components, which interact with receptors on epithelial and immune cells. In addition, bioactive components could be digested by intestinal microbiota to produce short-chain fatty acids and enhance energy utilization. Otherwise, microorganisms such as single-cell protein (SCP) and single-cell oils (SCOs) are sustainable and economic choices to replace conventional protein supplements and energy feeds. Supplementing microorganisms as feedstuffs and feed additives improved the average daily gain by 1.83%, the daily feed intake by 0.24%, and the feed efficiency by 1.46% in pigs and broilers. Based on the properties of each microorganism, traditional protein supplements, energy feeds, and functional feed additives could be replaced by microorganisms, which have shown benefits to animal's growth and health. Therefore, specific microorganisms could be promising alternatives as nutritional and functional feedstuffs in animal diets.

In-situ transesterification of single-cell oil for biodiesel production: a review

In recent years, biodiesel synthesis and production demands have increased because of its high degradability, cleaner emissions, non-toxicity, and an alternative to petroleum diesel. In this context, Single Cell Oil (SCO) has been identified as an alternative feedstock, having the advantage of accumulating high intracellular lipid. SCO/microbial lipids are potential alternatives for sustainable biodiesel production. The traditional technique for biodiesel production from the oils obtained from microbes generally requires two steps: lipid extraction and transesterification. In-situ transesterification is an innovative and renewable process for biodiesel production. It rules out the need to isolate and refine the feedstock lipid, as it directly uses biomass in a single step, i.e., the pretreated biomass will be subjected to in-situ transesterification in the presence of catalysts. Hence, the production cost can be reduced by eliminating the lipid extraction procedure. The current review focuses on the basic features and advantages of in-situ transesterification of SCO for biodiesel production with the aid of short-chain alcohols along with different acid, base, and enzyme catalysts. In addition, a comparative study was carried out to highlight the merits of in-situ transesterification over conventional transesterification.

Aspergillus caespitosus ASEF14, an oleaginous fungus as a potential candidate for biodiesel production using sago processing wastewater (SWW)

Background

Oleaginous microorganisms are sustainable alternatives for the production of biodiesel. Among them, oleaginous fungi are known for their rapid growth, short life cycles, no light requirement, easy scalability, and the ability to grow in cheap organic resources. Among all the sources used for biodiesel production, industrial wastewater streams have been least explored. We used oleaginous fungi to decontaminate sago processing wastewater and produce biodiesel.

Results

Among the 15 isolates screened for lipid production and starch utilization using the Nile red staining assay and amylase plate screening, three isolates accumulated > 20% (w/w) of their dry cell mass as lipids. The isolate ASEF14 exhibited the highest lipid accumulation (> 40%) and was identified as Aspergillus caespitosus based on the 28S rRNA gene sequencing. The maximum lipid content of 54.4% in synthetic medium (SM) and 37.2% in sago processing wastewater (SWW) was produced by the strain. The Fourier-transform infrared (FTIR) spectroscopy of the fungal oil revealed the presence of functional peaks corresponding to major lipids. Principal component analysis (PCA) of the FTIR data revealed major changes in the fatty acid composition during the transition from the growth phase (Days 1–3) to the lipid accumulation phase (Days 4–7). The fatty acid methyl esters (FAME) analysis of fungal oil from SWW contained 43.82% and 9.62% of saturated and monounsaturated fatty acids, respectively. The composition and percentage of individual FAME derived from SWW were different from SM, indicating the effect of nutrient and fermentation time. The fuel attributes of the SM- and SWW-grown fungal biodiesel (kinematic viscosity, iodine value, cetane number, cloud and pour point, linolenic acid content, FA > 4 double bonds) met international (ASTM D6751, EN 14214) and national (IS 15607) biodiesel standards. In addition to biodiesel production, the strain removed various contaminants such as total solids (TS), total suspended solids (TSS), total dissolved solids (TDS), dissolved oxygen (DO), chemical oxygen demand (COD), biological oxygen demand (BOD), total nitrogen (TN), total phosphorus (TP), and cyanide up to 58.6%, 53.0%, 35.2%, 94.5%, 89.3%, 91.3%, 74.0%, 47.0%, and 53.84%, respectively, from SWW.

Conclusion

These findings suggested that A. caespitosus ASEF14 is a potential candidate with high lipid accumulating ability (37.27%), capable of using SWW as the primary growth medium. The medium and incubation time alter the FAME profile of this fungus. The physical properties of fungal oil were in accordance with the biodiesel standards. Moreover, it decontaminated SWW by reducing several polluting nutrients and toxicants. The fungal biodiesel produced by this cost-effective method could serve as an alternate path to meet global energy demand.

The Potential of Single-Cell Oils Derived From Filamentous Fungi as Alternative Feedstock Sources for Biodiesel Production

Microbial lipids, also known as single-cell oils (SCOs), are highly attractive feedstocks for biodiesel production due to their fast production rates, minimal labor requirements, independence from seasonal and climatic changes, and ease of scale-up for industrial processing. Among the SCO producers, the less explored filamentous fungi (molds) exhibit desirable features such as a repertoire of hydrolyzing enzymes and a unique pellet morphology that facilitates downstream harvesting. Although several oleaginous filamentous fungi have been identified and explored for SCO production, high production costs and technical difficulties still make the process less attractive compared to conventional lipid sources for biodiesel production. This review aims to highlight the ability of filamentous fungi to hydrolyze various organic wastes for SCO production and explore current strategies to enhance the efficiency and cost-effectiveness of the SCO production and recovery process. The review also highlights the mechanisms and components governing lipogenic pathways, which can inform the rational designs of processing conditions and metabolic engineering efforts for increasing the quality and accumulation of lipids in filamentous fungi. Furthermore, we describe other process integration strategies such as the co-production with hydrogen using advanced fermentation processes as a step toward a biorefinery process. These innovative approaches allow for integrating upstream and downstream processing units, thus resulting in an efficient and cost-effective method of simultaneous SCO production and utilization for biodiesel production.

Symbiotic Associations: Key Factors That Determine Physiology and Lipid Accumulation in Oleaginous Microorganisms

Symbiosis naturally provides an opportunity for microorganisms to live together by mutual or one-way benefit. In symbiotic relationships, the microorganisms usually overcome the limitations of being free-living. Understanding the symbiotic relationships of oleaginous microorganisms provides potential route for the sustainable production of microbial-based alternative fuels. So far, several studies have been conducted in oleaginous microorganisms for the production of alternative fuels. However, some oleaginous microorganisms require high quantity of nutrients for their growth, and high level of energy and chemicals for harvest and separation of lipid bodies. Symbiotic associations can successfully be applied to address these issues. Of symbiotic associations, lichens and selective species of oleaginous endosymbiotic mucoromycotina have received substantial interest as better models to study the evolutionary relationships as well as single-cell oil production. Construction of artificial lichen system composed of cyanobacteria and oleaginous yeast has been achieved for sustainable production of lipids with minimum energy demand. Recently, endosymbiotic mucoromycotina species have been recognized as potential sources for biofuels. Studies found that endohyphal bacterium influences lipid profiling in endosymbiotic mucoromycotina species. Studies on the genetic factors related to oleaginous characteristics of endosymbiotic mucoromycotina species are scarce. In this regard, this review summarizes the different forms of symbiotic associations of oleaginous microorganisms and how symbiotic relationships are impacting the lipid formation in microorganisms. Further, the review also highlights the importance of evolutionary relationships and benefits of co-culturing (artificial symbiosis) approaches for sustainable production of biofuels.

Metabolism of Storage Lipids and the Role of Lipid Droplets in the Yeast Schizosaccharomyces pombe

Storage lipids, triacylglycerols (TAG), and steryl esters (SE), are predominant constituents of lipid droplets (LD) in fungi. In several yeast species, metabolism of TAG and SE is linked to various cellular processes, including cell division, sporulation, apoptosis, response to stress, and lipotoxicity. In addition, TAG are an important source for the generation of value-added lipids for industrial and biomedical applications. The fission yeast Schizosaccharomyces pombe is a widely used unicellular eukaryotic model organism. It is a powerful tractable system used to study various aspects of eukaryotic cellular and molecular biology. However, the knowledge of S. pombe neutral lipids metabolism is quite limited. In this review, we summarize and discuss the current knowledge of the homeostasis of storage lipids and of the role of LD in the fission yeast S. pombe with the aim to stimulate research of lipid metabolism and its connection with other essential cellular processes. We also discuss the advantages and disadvantages of fission yeast in lipid biotechnology and recent achievements in the use of S. pombe in the biotechnological production of valuable lipid compounds.

Microcultivation and FTIR spectroscopy-based screening revealed a nutrient-induced co-production of high-value metabolites in oleaginous Mucoromycota fungi

Mucoromycota fungi possess a versatile metabolism and can utilize various substrates for production of industrially important products, such as lipids, chitin/chitosan, polyphosphates, pigments, alcohols and organic acids. However, as far as commercialisation is concerned, establishing industrial biotechnological processes based on Mucoromycota fungi is still challenging due to the high production costs compared to the final product value. Therefore, the development of co-production concept is highly desired since more than one valuable product could be produced at the time and the process has a potentially higher viability. To develop such biotechnological strategy, we applied a high throughput approach consisting of micro-titre cultivation and FTIR spectroscopy. This approach allows single-step biochemical fingerprinting of either fungal biomass or growth media without tedious extraction of metabolites. The influence of two types of nitrogen sources and different levels of inorganic phosphorus on the co-production of lipids, chitin/chitosan and polyphosphates for nine different oleaginous Mucoromycota fungi was evaluated. FTIR analysis of biochemical composition of Mucoromycota fungi and biomass yield showed that variation in inorganic phosphorus had higher effect when inorganic nitrogen source-ammonium sulphate-was used. It was observed that: (1) Umbelopsis vinacea reached almost double biomass yield compared to other strains when yeast extract was used as nitrogen source while phosphorus limitation had little effect on the biomass yield; (2) Mucor circinelloides, Rhizopus stolonifer, Amylomyces rouxii, Absidia glauca and Lichtheimia corymbifera overproduced chitin/chitosan under the low pH caused by the limitation of inorganic phosphorus; (3) Mucor circinelloides, Amylomyces rouxii, Rhizopus stolonifer and Absidia glauca were able to store polyphosphates in addition to lipids when high concentration of inorganic phosphorus was used; (4) the biomass and lipid yield of high-value lipid producers Mortierella alpina and Mortierella hyalina were significantly increased when high concentrations of inorganic phosphorus were combined with ammonium sulphate, while the same amount of inorganic phosphorus combined with yeast extract showed negative impact on the growth and lipid accumulation. FTIR spectroscopy revealed the co-production potential of several oleaginous Mucoromycota fungi forming lipids, chitin/chitosan and polyphosphates in a single cultivation process.

Efficient simultaneous production of extracellular polyol esters of fatty acids and intracellular lipids from inulin by a deep-sea yeast Rhodotorula paludigena P4R5

BACKGROUND

Polyol esters of fatty acids (PEFA) are a kind of promising biosurfactants and mainly secreted by Rhodotorula strains. In addition, some strains of Rhodotorula are reliable producers of microbial lipid. Therefore, it is feasible to establish a one step fermentation process for efficient simultaneous production of PEFA and microbial lipids by a suitable Rhodotorula strain.

RESULTS

A newly isolated deep-sea yeast, Rhodotorula paludigena P4R5, was shown to simultaneously produce high level of intracellular lipid and extracellular PEFA. Under the optimized conditions, it could yield 48.5 g/L of PEFA and 16.9 g/L of intracellular lipid within 156 h from inulin during 10-L batch fermentation. The PEFA consisting of a mixture of mannitol esters of 3-hydroxy C14, C16 and C18 fatty acids with variable acetylation showed outstanding surface activity and emulsifying activity, while the fatty acids of the intracellular lipid were mainly C16 and C18 and could be high-quality feedstock for biodiesel production.

CONCLUSION

The deep-sea yeast strain R. paludigena P4R5 was an excellent candidate for efficient simultaneous of biosurfactants and biodiesel from inulin. Our results also suggested that the establishment of fermentation systems with multiple metabolites production was an effective approach to improve the profitability.

Growth and fatty acid profiles of Halophytophthora vesicula and Salispina spinosa from Philippine mangrove leaves

Studies on marine-sourced fatty acids have gathered significant interest recently as an important component of aquaculture feeds and of biofuel production. Of the organisms capable of producing fatty acids, marine oomycetes are promising model organisms. One group of marine oomycetes are the Halophytophthora spp. which is known to have an important role in leaf decomposition, thereby changing the plant debris into exudates which are usable to consumers in the mangrove ecosystems. This study reports the three mangrove oomycetes isolated from Philippine mangrove forests, identified herein as Halophytophthora vesicula AK1YB2 (Aklan), H. vesicula PQ1YB3 (Quezon) and Salispina spinosa ST1YB3 (Davao del Norte). These isolates were subjected to growth analyses using varying incubation parameters (salinity level and pH), and for fatty acid production. Results revealed the presence of different fatty acids such as Arachidonic acid, Linoleic acid and Vaccenic acid when grown on V8S and PYGS media. This study is the first observation of fatty acids from S. spinosa and H. vesicula from the Philippines. SIGNIFICANCE AND IMPACT OF THE STUDY: Tropical Philippines straddling west of the Pacific Ocean and East of South China Sea is rich in marine and estuarine oomycetes. These micro-organisms, hitherto poorly known and unstudied in the country, play an important role in the nutritive cycle of the mangrove ecosystem. Due to the increasing demand for an alternative source of fatty acids, species of Oomycetes isolated from select mangrove forests in Luzon, Visayas and Mindanao were analysed for their fatty acid contents. Prospects for industrially-important fatty acids make these Oomycetes all-important to study in applied microbiology in the Philippine setting where these structurally simple micro-organisms abound.

Interaction of nanoclay-reinforced packaging nanocomposites with food simulants and compost environments

The production of engineered nanomaterials (ENMs) has increased exponentially over the last few decades. ENMs, made from use of engineered nanoparticles (ENPs), have been applied to the food, agriculture, pharmaceutical, and automobile industries. Of particular interest are their applications in packaging nanocomposites for consumer and non-consumer goods. ENPs in nanocomposites are of interest as a packaging material because they reduce the amount of polymer needed, while improving the physical properties. However, the transformation of ENPs in nanocomposite production, their fate, and their toxicity remain unknown while in contact with the package content or after the end of life. The objectives of this chapter are (a) to provide an overview of the main nanoclays used in packaging; (b) to categorize the main polymeric packaging nanocomposites; (c) to provide an overview of the fate and mass transport of ENPs, especially nanoclays; (d) to describe the mass transfer of nanoclays in food simulants and in compost environments; and (e) to identify current and future research needs.

A new combined approach to improved lipid production using a strictly aerobic and oleaginous yeast

Microbial lipids have potential applications in energy, and food industry, because most of those lipids are triacylglycerol with long-chain fatty-acids that are comparable to conventional vegetable oils and can be obtained without arable land requirement. Rhodosporidium toruloides is a strictly aerobic strain, where oxygen plays a crucial role in growth, maintenance, and metabolite production, such as lipids and carotenoids. Dissolved oxygen concentration is one of the major factors affecting yeast physiological and biochemical characteristics. In this context, different approaches have been developed to increase available oxygen by the increasing the aeration and the addition of an oxygen-vector. The growth of R. toruloides in 2-L mechanical stirred tank reactor equipped with 1 or 2 porous spargers and a 70 C/N ratio, revealed a lipid content of 0.47 and 0.52 g/g and a lipidic productivity of 0.16 and 0.17 g/L day, respectively. The oxygen-vector addition, increased the lipidic productivity for 0.20 g/L day and a lipid contend of 0.51 g of lipids/g of biomass. The combined approach, combining high aeration (AA), and 1% of n-dodecane addition (DA), produced a significant improvement in the lipid accumulation (62%, w/w), when compared with the DA (51%, w/w) and the AA (52%, w/w) approaches. The increasing of lipids accumulation and smaller culture time are key factors for the success of scale-up and profitability of a bioprocess.

Concomitant production of chitosan and lipids from a newly isolated Mucor circinelloides ZSKP for biodiesel production

A newly-isolated oleaginous fungus Mucor circinelloides ZSKP concurrently yielded 21.4% lipids and 11.2% chitosan per gram of biomass. Parameters affecting the co-production were identified using Plackett-Burman design and were statistically optimized using Response Surface Methodology, which resulted in a 3-fold improvement in lipid production. The lipid profile showed a high content of unsaturated fatty acids including oleic (37%), linolenic (14%) and linoleic acids (19%), while palmitic acid was the major saturated fatty acid (21%). A comparative study to evaluate the efficacy of enzymatic (lipase) and chemical treatments for biodiesel production from fungal lipids and sunflower oil revealed enhanced production of biodiesel from fungal lipids. Synthesized biodiesel from M. circinelloides ZSKP satisfied standard specifications and had a higher cetane number (56), lower kinematic viscosity (4.6 mm²/s) and lower acid number (0.03) compared to sunflower oil. Results suggest Mucor circinelloides ZSKP is a promising candidate for implementation of the biorefinery concept.

Keggin-structure heteropolyacid supported on alumina to be used in trans/esterification of high-acid feedstocks

Heteropolyacids (HPA) with Keggin structures, such as H₃PMo₁₂O₄₀ (H₃PMo), have been described as efficient catalysts in trans/esterification reactions due to their tolerance to water and free fatty acids contents, with particularly well-suited characteristics of high proton mobility and stability. The versatile array of HPA is considerably increased when such catalysts are supported onto solid matrices. In this sense, Al₂O₃ was assessed as support for H₃PMo to be used in trans/esterification reactions to produce biodiesel from high-acid feedstocks. The catalyst structure was characterized and applied on trans/esterification reaction of acid oils using ethanol as acyl acceptor. A face centered composite design was employed to conduct the experimental design and results analysis, taking macaw palm oil as study model. The process achieved an optimum level of 99.8% ester content and 4.1 mm² s⁻¹ viscosity under the following reaction conditions: 190 °C reaction temperature, 50 : 1 ethanol-to-oil molar ratio and 13.0% catalyst concentration. Other tested feedstocks (fungal single cell oil and residual frying oil) were also tested promoting satisfactory results, though the parameters were found to be slightly outside the limits set by the USA (ASTM D6715) standard. The H₃PMo/Al₂O₃ catalyst presented good regeneration and can be reused for up to four reaction cycles and requires lower ethanol-to-oil ratio, temperature, and catalyst concentration in comparison with other data from the literature.

Heteropolyacids (HPA) with Keggin structures, such as H₃PMo₁₂O₄₀ (H₃PMo), have been described as efficient catalysts in trans/esterifications of high-acid feedstocks due to their tolerance to water and free fatty acids contents.

Oxidation stability of yeast biodiesel using Rancimat analysis: validation using infrared spectroscopy and gas chromatography-mass spectrometry

Biodiesel and single cell oils obtained from oleaginous yeasts grown in industrial waste are attractive alternatives to the conventional fuels. However, there are only few articles dealing with the stability of the microbial biofuels. Hence, this study aimed at characterizing the storage time of biodiesels using Rancimat methods. The microbial oil and the biodiesel obtained from microbial oil have been characterized with storage stability due to various oxidizing and thermal damage. Here, the microbial fuels were subject to Rancimat analysis and found to have high thermal-oxidative stability of 18 and 8.78 h for biodiesel and oil, respectively. The storage stability resulting from storage conditions was extrapolated for biodiesel and oil and has been found to be 1.62 and 0.54 years, respectively. The infrared spectroscopic analysis reveals the degree of oxidation found after the induction time was reached and shows the characteristic peaks for degradation products. Gas chromatography revealed the compounds that were responsible for the stability as well as the amount of degradation products left.

Biodiesel Production from Palm Oil, Its By-Products, and Mill Effluent: A Review

The sustainability of petroleum-based fuel supply has gained broad attention from the global community due to the increase of usage in various sectors, depletion of petroleum resources, and uncertain around crude oil market prices. Additionally, environmental problems have also arisen from the increasing emissions of harmful pollutants and greenhouse gases. Therefore, the use of clean energy sources including biodiesel is crucial. Biodiesel is mainly produced from unlimited natural resources through a transesterification process. It presents various advantages over petro-diesel; for instance, it is non-toxic, biodegradable, and contains less air pollutant per net energy produced with low sulphur and aromatic content, apart from being safe. Considering the importance of this topic, this paper focuses on the use of palm oil, its by-products, and mill effluent for biodiesel production. Palm oil is known as an excellent raw material because biodiesel has similar properties to the regular petro-diesel. Due to the debate on the usage of palm oil as food versus fuel, extensive studies have been conducted to utilise its by-products and mill effluent as raw materials. This paper also discusses the properties of biodiesel, the difference between palm-biodiesel and other biodiesel sources, and the feasibility of using palm oil as a primary source for future alternative and sustainable energy sources.

Diversity and characterization of cultivable oleaginous yeasts isolated from mangrove forests

A total of 198 yeasts were isolated from 140 samples collected from 7 mangrove forests in 4 provinces of Thailand, and were found to belong to 30 genera, 45 described species and at least 12 undescribed species based on their 26S rRNA (D1/D2 domain) gene sequence. The most prevalent species was Candida tropicalis, followed by Candida pseudolambica and Rhodosporidium paludigena. Lipid accumulation, as determined by Nile red staining, of the isolated yeasts revealed that 69 and 18 strains were positive and strongly positive, respectively, while quantitative analysis of the intracellular lipid accumulated in the latter indicated that 10 of these strains, Pseudozyma tsukubaensis (YWT7-2 and YWT7-3), Rhodotorula sphaerocarpa (YWW6-1 and SFL14-1SF), Saitozyma podzolica (YWT1-1, NS3-3 and NS10-2), Prototheca zopfii var. hydrocarbonea OMS6-1 and Prototheca sp. (YMTW3-1 and YMTS5-2), were oleaginous. In this study we found that under nitrogen depletion condition (155 C/N ratio) Pseudozyma tsukubaensis YWT7-2 accumulated the highest level of intracellular lipid at 32.4% (w/w, dry cell weight), with a broadly similar fatty acid composition to that in palm oil.

A comparative study between fungal pellet- and spore-assisted microalgae harvesting methods for algae bioflocculation

Fungi assisted microalgae bioflocculation is an emerging, efficient and cost-effective microalgal harvesting method, but no study has systematically evaluated and compared fungal spore-assisted (FSA) and fungal pellet-assisted (FPA) microalgal harvesting methods. In this study, harvesting Chlorella sp. cells by co-culture with Penicillium sp. spores or pellets was compared. Temperature, glucose concentration, pH and fungi:algae ratio were the critical parameters for harvesting efficiency. The highest flocculation efficiency (99%) of FSA method was achieved in 28 h at 40 °C, 160 rpm, 5 g glucose/L and 1.1 × 10⁴ cells/mL (spore). FPA method can harvest 98.26% algae cells in 2.5 h at 34 °C, 160 rpm, pH 4.0 with the fungi:algae ratio of 1:2. The carbon input for FPA is only half of that for FSA. FPA takes less time and needs less glucose input compared with FSA and may be more promising to be further developed as an effective microalgae bioflocculation method.

Metals in mangrove ecosystems and associated biota: A global perspective

Mangrove forests prevalent along the intertidal regions of tropical and sub-tropical coastlines are inimitable and dynamic ecosystems. They protect and stabilize coastal areas from deleterious consequences of natural disasters such as hurricanes and tsunamis. Although there are reviews on ecological aspects, industrial uses of mangrove-associated microorganisms and occurrence of pollutants in a region-specific manner, there is no exclusive review detailing the incidence of metals in mangrove sediments and associated biota in these ecosystems on a global level. In this review, mangrove forests have been classified in a continent-wise manner. Most of the investigations detail the distribution of metals such as zinc, chromium, arsenic, copper, cobalt, manganese, nickel, lead and mercury although in some cases levels of vanadium, strontium, zirconium and uranium have also been studied. Seasonal, tidal, marine, riverine, and terrestrial components are seen to influence occurrence, speciation, bioavailability and fate of metals in these ecosystems. In most of the cases, associated plants and animals also accumulate metals to different extents and are of ecotoxicological relevance. Levels of metals vary in a region specific manner and there is disparity in the pollution status of different mangrove areas. Protecting these vulnerable ecosystems from metal pollutants is important from environmental safety point of view.

Lipid extraction from the biomass of Trichoderma koningiopsis MX1 produced in a non-stirring culture for potential biodiesel production

Oleaginous microorganisms such as microalgae, yeasts, bacteria and filamentous fungi are alternative sources of vegetal or animal fats for biodiesel production. This research evaluated the lipid production by the biomass Trichoderma koningiopsis MX1 with a non-stirring culture at room temperature, and fungal lipids were extracted through three techniques for biodiesel generation purposes. The three modified lipid extraction techniques yielded 18.4, 10.3 and 17.1 % of fungal lipids. The trans-esterification of lipids indicated that the controlling components for biodiesel were palmitic (40.8 %) and linoleic acids (ranging from 37.6 % to 41.2 %). Results show that fungal cultural conditions and the lipid extraction technique are determinants for producing biodiesel from fungal lipids. Therefore, the modification of some of these conditions could increase their efficiency and viability.

Mutants of Yarrowia lipolytica NCIM 3589 grown on waste cooking oil as a biofactory for biodiesel production

Background

Oleaginous yeasts are fast emerging as a possible feedstock for biodiesel production. Yarrowia lipolytica, a model oleaginous yeast is known to utilize a variety of hydrophobic substrates for lipid accumulation including waste cooking oil (WCO). Approaches to increase lipid content in this yeast include metabolic engineering which requires manipulation of multiple genes in the lipid biosynthesis pathway. A classical and cost-effective approach, namely, random chemical mutagenesis on the yeast can lead to increased production of biodiesel as is explored here.

Results

In this study, chemical mutagenesis using the alkylating agent, N- methyl-N′-nitro-N-nitrosoguanidine (MNNG) as well as an additional treatment with cerulenin, a fatty acid synthase inhibitor generated 800 mutants of Y. lipolytica NCIM 3589 (761 MNNG treated and 39 MNNG + cerulenin treated). A three-stage screening using Sudan Black B plate technique, Nile red fluorimetry and total lipid extraction using solvent was performed, which enabled selection of ten high lipid yielding mutants. Time course studies of all the ten mutants were further undertaken in terms of biomass, lipid yield and lipid content to select three stable mutants (YlB6, YlC7 and YlE1) capable of growing and accumulating lipid on WCO, with lipid contents of 55, 60 and 67% as compared to 45% for the wild type. The mutants demonstrated increased volumetric lipid productivities (0.062, 0.044 and 0.041 g L⁻¹ h⁻¹) as compared to the wild type (0.033 g L⁻¹ h⁻¹). The fatty acid profile of the three mutants consisted of a high content of C16 and C18 saturated and monounsaturated fatty acids and was found to be suitable for biodiesel production. The fuel properties, namely, density, kinematic viscosity, total acid number, iodine value of the three mutants were evaluated and found to lie within the limits specified by internationally accepted standards. Additionally, it was noted that the mutants demonstrated better cetane numbers and higher heating values than the wild type strain.

Conclusion

The chemical mutagenesis strategy adopted in this study resulted in the successful isolation of three stable high SCO yielding mutants. The mutants, namely, YlB6, YlC7 and YlE1 exhibited a 1.22, 1.33 and 1.49-fold increase in lipid contents when grown on 100 g L⁻¹ waste cooking oil than the parental yeast strain. The fatty acid methyl ester (FAME) profiles of all the three mutants was determined to be suitable for biodiesel suggesting their potential applicability while simultaneously addressing the management of waste cooking oil.

Electronic supplementary material

The online version of this article (doi:10.1186/s12934-017-0790-x) contains supplementary material, which is available to authorized users.

Microbial oil - A plausible alternate resource for food and fuel application

Microbes have recourse to low-priced substrates like agricultural wastes and industrial efflux. A pragmatic approach towards an emerging field- the exploitation of microbial oils for biodiesel production, pharmaceutical and cosmetic applications, food additives, biopolymer production will be of immense remunerative significance in the near future. Due to high free fatty acid, nutritive content and simpler solvent extraction processes of microbial oils with plant oil, microbial oils can back plant oils in food applications. The purpose of this review is to evaluate the opulence of lipid production in native and standard micro-organisms and also to emphasize the vast array of applications including food and fuel by obtaining maximum yield.

Waste Soybean Oil and Corn Steep Liquor as Economic Substrates for Bioemulsifier and Biodiesel Production by Candida lipolytica UCP 0998

Almost all oleaginous microorganisms are available for biodiesel production, and for the mechanism of oil accumulation, which is what makes a microbial approach economically competitive. This study investigated the potential that the yeast Candida lipolytica UCP0988, in an anamorphous state, has to produce simultaneously a bioemulsifier and to accumulate lipids using inexpensive and alternative substrates. Cultivation was carried out using waste soybean oil and corn steep liquor in accordance with 2² experimental designs with 1% inoculums (10⁷ cells/mL). The bioemulsifier was produced in the cell-free metabolic liquid in the late exponential phase (96 h), at Assay 4 (corn steep liquor 5% and waste soybean oil 8%), with 6.704 UEA, IE₂₄ of 96.66%, and showed an anionic profile. The emulsion formed consisted of compact small and stable droplets (size 0.2–5 µm), stable at all temperatures, at pH 2 and 4, and 2% salinity, and showed an ability to remove 93.74% of diesel oil from sand. The displacement oil (ODA) showed 45.34 cm² of dispersion (central point of the factorial design). The biomass obtained from Assay 4 was able to accumulate lipids of 0.425 g/g biomass (corresponding to 42.5%), which consisted of Palmitic acid (28.4%), Stearic acid (7.7%), Oleic acid (42.8%), Linoleic acid (19.0%), and γ-Linolenic acid (2.1%). The results showed the ability of C. lipopytica to produce both bioemulsifier and biodiesel using the metabolic conversion of waste soybean oil and corn steep liquor, which are economic renewable sources.

Assessing an effective feeding strategy to optimize crude glycerol utilization as sustainable carbon source for lipid accumulation in oleaginous yeasts

Background

Microbial lipids can represent a valuable alternative feedstock for biodiesel production in the context of a viable bio-based economy. This production can be driven by cultivating some oleaginous microorganisms on crude-glycerol, a 10 % (w/w) by-product produced during the transesterification process from oils into biodiesel. Despite attractive, the perspective is still economically unsustainable, mainly because impurities in crude glycerol can negatively affect microbial performances. In this view, the selection of the best cell factory, together with the development of a robust and effective production process are primary requirements.

Results

The present work compared crude versus pure glycerol as carbon sources for lipid production by three different oleaginous yeasts: Rhodosporidium toruloides (DSM 4444), Lipomyces starkeyi (DSM 70295) and Cryptococcus curvatus (DSM 70022). An efficient yet simple feeding strategy for avoiding the lag phase caused by growth on crude glycerol was developed, leading to high biomass and lipid production for all the tested yeasts. Flow-cytometry and fourier transform infrared (FTIR) microspectroscopy, supported by principal component analysis (PCA), were used as non-invasive and quick techniques to monitor, compare and analyze the lipid production over time. Gas chromatography (GC) analysis completed the quali-quantitative description. Under these operative conditions, the highest lipid content (up to 60.9 % wt/wt) was measured in R. toruloides, while L. starkeyi showed the fastest glycerol consumption rate (1.05 g L⁻¹ h⁻¹). Being productivity the most industrially relevant feature to be pursued, under the presented optimized conditions R. toruloides showed the best lipid productivity (0.13 and 0.15 g L⁻¹ h⁻¹ on pure and crude glycerol, respectively).

Conclusions

Here we demonstrated that the development of an efficient feeding strategy is sufficient in preventing the inhibitory effect of crude glycerol, and robust enough to ensure high lipid accumulation by three different oleaginous yeasts. Single cell and in situ analyses allowed depicting and comparing the transition between growth and lipid accumulation occurring differently for the three different yeasts. These data provide novel information that can be exploited for screening the best cell factory, moving towards a sustainable microbial biodiesel production.

Electronic supplementary material

The online version of this article (doi:10.1186/s12934-016-0467-x) contains supplementary material, which is available to authorized users.

Conversion of dried Aspergillus candidus mycelia grown on waste whey to biodiesel by in situ acid transesterification

This study reports optimization of the transesterification reaction step on dried biomass of an oleaginous fungus Aspergillus candidus grown on agro-dairy waste, whey. Acid catalyzed transesterification was performed and variables affecting esterification, viz., catalyst methanol and chloroform concentrations, temperature, time, and biomass were investigated. Statistical optimization of the transesterification reaction using Plackett-Burman Design showed biomass to be the predominant factor with a 12.5-fold increase in total FAME from 25.6 to 320mg. Studies indicate that the transesterification efficiency in terms of conversion is favored by employing lower biomass loadings. A. candidus exhibited FAME profiles containing desirable saturated (30.2%), monounsaturated (31.5%) and polyunsaturated methyl esters (38.3%). The predicted and experimentally determined biodiesel properties (density, kinematic viscosity, iodine value, cetane number, TAN, water content, total and free glycerol) were in accordance with international (ASTM D6751, EN 14214) and national (IS 15607) standards.

Engineering Yarrowia lipolytica to produce biodiesel from raw starch

BACKGROUND

In the last year, the worldwide concern about the abuse of fossil fuels and the seeking for alternatives sources to produce energy have found microbial oils has potential candidates for diesel substitutes. Yarrowia lipolytica has emerged as a paradigm organism for the production of bio-lipids in white biotechnology. It accumulates high amounts of lipids from glucose as sole carbon sources. Nonetheless, to lower the cost of microbial oil production and rival plant-based fuels, the use of raw and waste materials as fermentation substrate is required. Starch is one of the most abundant carbohydrates in nature and it is constituted by glucose monomers. Y. lipolytica lacks the capacity to breakdown this polymer and thus expensive enzymatic and/or physical pre-treatments are needed.

RESULTS

In this work, we express heterologous alpha-amylase and glucoamylase enzymes in Y. lipolytica. The modified strains were able to produce and secrete high amounts of active form of both proteins in the culture media. These strains were able to grow on starch as sole carbon source and produce certain amount of lipids. Thereafter, we expressed both enzymes in an engineered strain able to overaccumulate lipids. This strain was able to produce up to 21 % of DCW as fatty acids from soluble starch, 5.7 times more than the modified strain in the wild-type background. Media optimization to increase the C/N ratio to 90 increased total lipid content up to 27 % of DCW. We also tested these strains in industrial raw starch as a proof of concept of the feasibility of the consolidated bioprocess. Lipid production from raw starch was further enhanced by the expression of a second copy of each enzyme. Finally, we determined in silico that the properties of a biodiesel produced by this strain from raw starch would fit the established standards.

CONCLUSIONS

In this work, we performed a strain engineering approach to obtain a consolidated bioprocess to directly produce biolipids from raw starch. Additionally, we proved that lipid production from starch can be enhanced by both metabolic engineering and culture condition optimization, setting up the basis for further studies.

Biosynthesis, characterization and enzymatic transesterification of single cell oil of Mucor circinelloides--a sustainable pathway for biofuel production

The filamentous fungus Mucor circinelloides URM 4182 was tested to determine its ability to produce single-cell oil suitable for obtaining biodiesel. Cell growth and lipid accumulation were investigated in a medium containing glucose as the main carbon source. A microwave-assisted ethanol extraction technique (microwave power ⩽200 W, 50-60 °C) was established and applied to lipid extraction from the fungal hyphae to obtain high lipid concentration (44%wt) of the dry biomass, which was considerably higher than the quantity obtained by classical solvent methods. The lipid profile showed a considerable amount of oleic acid (39.3%wt), palmitic acid (22.2%wt) and γ-linoleic acid (10.8%wt). Biodiesel was produced by transesterification of the single-cell oil with ethanol using a immobilized lipase from Candida antarctica (Novozym® 435) as the catalyst. (1)H NMR and HPLC analyses confirmed conversion of 93% of the single-cell oil from M. circinelloides into ethyl esters (FAEE).

Fungal-assisted algal flocculation: application in wastewater treatment and biofuel production

BACKGROUND

The microalgal-based industries are facing a number of important challenges that in turn affect their economic viability. Arguably the most important of these are associated with the high costs of harvesting and dewatering of the microalgal cells, the costs and sustainability of nutrient supplies and costly methods for large scale oil extraction. Existing harvesting technologies, which can account for up to 50% of the total cost, are not economically feasible because of either requiring too much energy or the addition of chemicals. Fungal-assisted flocculation is currently receiving increased attention because of its high harvesting efficiency. Moreover, some of fungal and microalgal strains are well known for their ability to treat wastewater, generating biomass which represents a renewable and sustainable feedstock for bioenergy production.

RESULTS

We screened 33 fungal strains, isolated from compost, straws and soil for their lipid content and flocculation efficiencies against representatives of microalgae commercially used for biodiesel production, namely the heterotrophic freshwater microalgae Chlorella protothecoides and the marine microalgae Tetraselmis suecica. Lipid levels and composition were analyzed in fungal-algal pellets grown on media containing alternative carbon, nitrogen and phosphorus sources from wheat straw and swine wastewater, respectively. The biomass of fungal-algal pellets grown on swine wastewater was used as feedstock for the production of value-added chemicals, biogas, bio-solids and liquid petrochemicals through pyrolysis. Co-cultivation of microalgae and filamentous fungus increased total biomass production, lipid yield and wastewater bioremediation efficiency.

CONCLUSION

Fungal-assisted microalgal flocculation shows significant potential for solving the major challenges facing the commercialization of microalgal biotechnology, namely (i) the efficient and cost-effective harvesting of freshwater and seawater algal strains; (ii) enhancement of total oil production and optimization of its composition; (iii) nutrient supply through recovering of the primary nutrients, nitrogen and phosphates and microelements from wastewater. The biomass generated was thermochemically converted into biogas, bio-solids and a range of liquid petrochemicals including straight-chain C12 to C21 alkanes which can be directly used as a glycerine-free component of biodiesel. Pyrolysis represents an efficient alternative strategy for biofuel production from species with tough cell walls such as fungi and fungal-algal pellets.

Designing of a "cheap to run" fermentation platform for an enhanced production of single cell oil from Yarrowia lipolytica DSM3286 as a potential feedstock for biodiesel

In this study, the culture medium components screening and filtering were undertaken in order to set up efficient and cost effective minimal culture media for lipid production from Yarrowia lipolytica DSM3286. The basal minimal culture medium (S2) designed yielded lipid content up to 35% of the microbial dry cell weight. A set of fermentation strategies based on this minimal medium was developed and the lipid content was raised to 51%. The scale-up under different fermentation conditions based on S2 medium led to a maximum lipid content of 65%. The produced microbial oils displayed interesting properties to be used as a feedstock for high quality biodiesel production. The minimal media and operable cultivation strategies devised in this study, in association with the works done so far by other authors, could enable fast, massive, viable and more economical production of single cell oils and smooth biodiesel manufacture.

Co-cultivation of fungal and microalgal cells as an efficient system for harvesting microalgal cells, lipid production and wastewater treatment

The challenges which the large scale microalgal industry is facing are associated with the high cost of key operations such as harvesting, nutrient supply and oil extraction. The high-energy input for harvesting makes current commercial microalgal biodiesel production economically unfeasible and can account for up to 50% of the total cost of biofuel production. Co-cultivation of fungal and microalgal cells is getting increasing attention because of high efficiency of bio-flocculation of microalgal cells with no requirement for added chemicals and low energy inputs. Moreover, some fungal and microalgal strains are well known for their exceptional ability to purify wastewater, generating biomass that represents a renewable and sustainable feedstock for biofuel production. We have screened the flocculation efficiency of the filamentous fungus A. fumigatus against 11 microalgae representing freshwater, marine, small (5 µm), large (over 300 µm), heterotrophic, photoautotrophic, motile and non-motile strains. Some of the strains are commercially used for biofuel production. Lipid production and composition were analysed in fungal-algal pellets grown on media containing alternative carbon, nitrogen and phosphorus sources contained in wheat straw and swine wastewater, respectively. Co-cultivation of algae and A. fumigatus cells showed additive and synergistic effects on biomass production, lipid yield and wastewater bioremediation efficiency. Analysis of fungal-algal pellet's fatty acids composition suggested that it can be tailored and optimised through co-cultivating different algae and fungi without the need for genetic modification.

Inhibition of bacterial quorum sensing by extracts from aquatic fungi: first report from marine endophytes

In our search for quorum-sensing (QS) disrupting molecules, 75 fungal isolates were recovered from reef organisms (endophytes), saline lakes and mangrove rhizosphere. Their QS inhibitory activity was evaluated in Chromobacterium violaceum CVO26. Four strains of endophytic fungi stood out for their potent activity at concentrations from 500 to 50 μg mL⁻¹. The molecular characterization, based on the internal transcribed spacer (ITS) region sequences (ITS1, 5.8S and ITS2) between the rRNA of 18S and 28S, identified these strains as belonging to four genera: Sarocladium (LAEE06), Fusarium (LAEE13), Epicoccum (LAEE14), and Khuskia (LAEE21). Interestingly, three came from coral species and two of them came from the same organism, the coral Diploria strigosa. Metabolic profiles obtained by Liquid Chromatography-High Resolution Mass Spectrometry (LC-HRMS) suggest that a combination of fungal secondary metabolites and fatty acids could be the responsible for the observed activities. The LC-HRMS analysis also revealed the presence of potentially new secondary metabolites. This is, to the best of our knowledge, the first report of QS inhibition by marine endophytic fungi.

Getting lipids from glycerol: new perspectives on biotechnological exploitation of Candida freyschussii

BACKGROUND

Microbial lipids represent a valuable alternative feedstock for biodiesel production when oleaginous microbes are cultured with inexpensive substrates in processes exhibiting high yield and productivity. In this perspective, crude glycerol is among the most promising raw materials for lipid production, because it is the costless residual of biodiesel production. Thus, cultivation of oleaginous yeasts in glycerol-based media is attracting great interest and natural biodiversity is increasingly explored to identify novel oleaginous species recycling this carbon source for growth and lipid production.

RESULTS

Thirty-three yeasts strains belonging to 19 species were screened for the ability to grow and produce intracellular lipids in a pure glycerol-based medium with high C/N ratio. A minority of them consumed most of the glycerol and generated visible lipid bodies. Among them, Candida freyschussii ATCC 18737 was selected, because it exhibited the highest lipid production and glycerol conversion yield. Lipid production in this strain was positively affected by the increase of C/N ratio, but growth was inhibited by glycerol concentration higher than 40 g/L. In batch cultures, the highest lipid production (4.6 g/L), lipid content of biomass (33% w/w), and lipid volumetric productivity (0.15 g/L/h) were obtained with 40 g/L glycerol, during the course of a 30-h process. Fed-batch cultivation succeeded in preventing substrate inhibition and in achieving a high cell-density culture. The improved lipid production and volumetric productivity reached the remarkable high level of 28 g/L and 0.28 g/L/h, respectively. The lipids accumulated by C. freyschussii ATCC 18737 have similar fatty acid composition of plant oil indicating their potential use as biodiesel feedstock. Calculated physicochemical properties of a biodiesel produced with the lipids from C. freyschussii ATCC 18737 are expected to meet the European and American standards, being equal to those of rapeseed and palm biodiesel.

CONCLUSIONS

C. freyschussii ATCC 18737 could be considered an interesting microorganism for utilization in biofuel industry. Cultivation of this yeast in media containing crude glycerol should be investigated deeper in order to evaluate whether it may find application in the valorization of the waste of biodiesel manufacturing.

Fourier transform infrared spectroscopy as a method to study lipid accumulation in oleaginous yeasts

BACKGROUND

Oleaginous microorganisms, such as different yeast and algal species, can represent a sustainable alternative to plant oil for the production of biodiesel. They can accumulate fatty acids (FA) up to 70% of their dry weight with a predominance of (mono)unsaturated species, similarly to what plants do, but differently from animals. In addition, their growth is not in competition either with food, feed crops, or with agricultural land.Despite these advantages, the exploitation of the single cell oil system is still at an early developmental stage. Cultivation mode and conditions, as well as lipid extraction technologies, represent the main limitations. The monitoring of lipid accumulation in oleaginous microorganisms is consequently crucial to develop and validate new approaches, but at present the majority of the available techniques is time consuming, invasive and, when relying on lipid extraction, can be affected by FA degradation.

RESULTS

In this work the fatty acid accumulation of the oleaginous yeasts Cryptococcus curvatus and Rhodosporidium toruloides and of the non-oleaginous yeast Saccharomyces cerevisiae (as a negative control) was monitored in situ by Fourier Transform Infrared Spectroscopy (FTIR). Indeed, this spectroscopic tool can provide complementary information to those obtained by classical techniques, such as microscopy, flow cytometry and gas chromatography. As shown in this work, through the analysis of the absorption spectra of intact oleaginous microorganisms it is possible not only to monitor the progression of FA accumulation but also to identify the most represented classes of the produced lipids.

CONCLUSIONS

Here we propose FTIR microspectroscopy - supported by multivariate analysis - as a fast, reliable and non invasive method to monitor and analyze FA accumulation in intact oleaginous yeasts. The results obtained by the FTIR approach were in agreement with those obtained by the other classical methods like flow cytometry and gas chromatography. Moreover, the possibility to track lipid production in real time is highly desirable to support the initial screening of strains and media as well as to optimize the scaling up experiments, which are essential for a viable and successful development of an industrial production process.

Harnessing indigenous plant seed oil for the production of bio-fuel by an oleaginous fungus, Cunninghamella blakesleeana- JSK2, isolated from tropical soil

Cunninghamella blakesleeana- JSK2, a gamma-linolenic acid (GLA) producing tropical fungal isolate, was utilized as a tool to evaluate the influence of various plant seed oils on biomass, oleagenicity and bio-fuel production. The fungus accumulated 26 % total lipid of their dry biomass (2 g/l) and 13 % of GLA in its total fatty acid. Among the various plant seed oils tested as carbon sources for biotransformation studies, watermelon oil had an effect on biomass and total lipid increasing up to 9.24 g/l and 34 % respectively. Sunflower, pumpkin, and onion oil increased GLA content between 15-18 %. Interestingly, an indigenous biodiesel commodity, Pongamia pinnata oil showed tremendous effect on fatty acid profile in C. blakesleeana- JSK2, when used as a sole source of carbon. There was complete inhibition of GLA from 13 to 0 % and increase in oleic acid content, one of the key components of biodiesel to 70 % (from 20 % in control). Our results suggest the potential application of indigenous plant seed oils, particularly P. pinnata oil, for the production of economically valuable bio-fuel in oleaginous fungi in general, and C. blakesleeana- JSK2, in particular.