Animal models for implant biomaterial research in bone: a review

Hard and soft tissue healing around implants with Ag coating: An experimental study in dogs

Introduction The purpose of this randomized controlled canine experimental study was to evaluate peri‑implant hard and soft tissue healing around implants with silver coating. Methods All mandibular premolars and molars of five male beagle dogs were extracted. 25 test and 25 control implants were randomly installed and connected with the healing abutments. After 2 and 4 month healing period, implants with soft and hard tissues were obtained for histologic and histomorphometric analysis. Results In mesio-distal sections, supracrestal tissue attachment dimensions were 4.03±0.48 mm and 4.25±0.66 mm for test and 4.34±0.6 mm and 5.21±0.72 mm for control implants at 2 and 4 month healing time. The respective crestal bone loss values were 1.10±0.69 mm and 0.74±0.67 mm for test and 1.13±0.48 mm and 1.49±0.65 mm for control implants. The differences were statistically significant only in the 4-month healing period. In buccolingual sections, supracrestal tissue attachment height at 2 and 4 month healing periods were 4.09±0.64 mm and 4.5±0.8 mm for test implants and 4.17±0.76 mm and 4.48±0.76 mm for control implants. The respective mean values for crestal bone loss were 1.31±0.6 mm and 1.02±0.58 mm for test implants, and 1.28±0.61 mm and 1.29±0.69 mm for control implants. No statistical significant differences were recorded, apart from the height of connective tissue at the 2 month healing group. No significant difference in terms of BIC between implants or healing periods was recorded. Conclusions The Ag implant coating resulted in smaller supracrestal tissue attachment dimensions and less bone loss. Within the limits of a canine study, prevention of crestal bone loss along with the effectiveness of Ag antimicrobial properties in dental implantology is demonstrated.

A Standardized Rat Model to Study Peri-implantitis of Transmucosal Osseointegrated Implants

With the high incidence rate, distinctive implant characteristic and unique infection pattern, peri-implantitis (PI) requires a specially designed implant animal model for the researches on the pathogenesis and treatments. Previous small-animal PI models exhibit variability in implant site selection, design, and surgical procedures resulting in unnecessary tissue damage and less effectivity. Herein, a quantitative-analysis-based standardized rat model for transmucosal PI-related research was proposed. After dissecting the anatomic structures of the rat maxilla, we determined that placing the implant anterior to the molars in the rat maxilla streamlined the experimental period and enhanced animal welfare. We standardized the model by controlling the rat strain, gender, and size. The customized implant and a series of matched surgical instruments were appropriately designed. A clear, step-by-step surgical process was established. These designs ensured the success rate, stability, and replicability of the model. Each validation method confirmed the successful construction of the model. This study proposed a quantitative-analysis-based standardized transmucosal PI rat model with improved animal welfare and reliable procedures. This model could provide efficient in vivo insights to study the pathogenesis and treatments of PI and preliminary screening data for further large-animal and clinical trials.

The Suitability of Trabecular Patterns in the Assessment of Dental Implant Osseointegration Process through 2D Digital and 3D CBCT Radiographs

OBJECTIVE

 The research aims to determine the suitability of the trabecular pattern in the assessment of the dental implant osseointegration process through two-dimensional (2D) digital and three-dimensional (3D) cone-beam computed tomography (CBCT) radiographs.

MATERIALS AND METHODS

 This is a correlation description that explains the relationship between variables. The population consisted of 24 data points on 3D CBCT and 2D digital radiographs from the procedure after dental implants were inserted into the tibia of a New Zealand white rabbit (Oryctolagus cuniculus) on days 3, 14, and 28. The radiograph was selected based on the region of interest (ROI), which covers the peri-implant area with a width of 1 mm and length following the height of the implant. The ROI was analyzed for trabecular thickness (Tb.Th), separation (Tb.Sp), number (Tb.N), and fractal dimension.

STATISTICAL ANALYSIS

 The intraclass correlation coefficient (ICC) was used to statistically test the data to assess the consistency of intraobserver measurements and the r value (Pearson's correlation coefficient). This determines the correlation between trabecular patterns in both radiographic modalities and the Bland-Altman plot to observe the limits of acceptable discrepancies.

RESULTS

 The ICC test showed high intraobserver consistency in trabecular pattern measurements on 2D digital radiographs and 3D CBCT. The trabecular space pattern and number showed an r value of 0.88 with radiographic modalities of 0.72 mm and 0.018, respectively. Additionally, the trabecular thickness and fractal dimension had an insignificant correlation, with an r value of 0.22, and the mean of the 2D radiograph was lower than that of CBCT.

CONCLUSION

 The 2D radiograph and 3D CBCT showed correlations in the trabecular number and space results but had no correlation in the trabecular thickness and fractal dimension results. Based on intraclass correlation analysis, 3D CBCT appeared to be more reliable for measuring trabecular patterns (Tb.Th, Tb.Sp, Tb.N, and fractal dimension) than 2D radiograph.

Tailoring Biomaterials Ameliorate Inflammatory Bone Loss

Inflammatory diseases, such as rheumatoid arthritis, periodontitis, chronic obstructive pulmonary disease, and celiac disease, disrupt the delicate balance between bone resorption and formation, leading to inflammatory bone loss. Conventional approaches to tackle this issue encompass pharmaceutical interventions and surgical procedures. Nevertheless, pharmaceutical interventions exhibit limited efficacy, while surgical treatments impose trauma and significant financial burden upon patients. Biomaterials show outstanding spatiotemporal controllability, possess a remarkable specific surface area, and demonstrate exceptional reactivity. In the present era, the advancement of emerging biomaterials has bestowed upon more efficacious solutions for combatting the detrimental consequences of inflammatory bone loss. In this review, the advances of biomaterials for ameliorating inflammatory bone loss are listed. Additionally, the advantages and disadvantages of various biomaterials-mediated strategies are summarized. Finally, the challenges and perspectives of biomaterials are analyzed. This review aims to provide new possibilities for developing more advanced biomaterials toward inflammatory bone loss.

A comparison of maceration methods for the preparation of infant skeletal remains for forensic anthropological analysis

Very little literature currently exists prescribing which maceration method to use when preparing infant human remains, resulting in bone quality that is suitable for forensic anthropological analysis. The aim of the study was to test five maceration methods to determine which is most suitable for infant remains for forensic anthropological analysis. The sample included five neonate pig carcasses (Sus scrofa domesticus), ranging between one to three days old. Five maceration methods were tested on the pig carcasses (one pig per maceration method) to determine their effectiveness. The methods included invertebrate maceration by meal worms, chemical maceration by bleach, chemical maceration by borax solution, enzymatic maceration by laundry detergent and sodium carbonate solution, and chemical maceration by sodium hypochlorite. A scoring method was created to assess the effectiveness of each maceration method. Invertebrate maceration and chemical maceration using bleach were the least successful methods of maceration (total maceration score = 8 respectively). Chemical maceration using borax and chemical maceration using sodium hypochlorite achieved complete maceration of the skeletal remains; however, they both resulted in artifacts that are unsuitable for forensic analysis (total maceration score = 14 respectively). Enzymatic maceration using laundry detergent and sodium carbonate was the most successful method (total maceration score = 17). The detergent technique subsequently successfully macerated all five sets of infant human remains. This study has validated that the enzymatic maceration technique using laundry detergent and sodium carbonate can be used to effectively macerate the remains of infant skeletal remains for forensic anthropological analysis.

XRF identification of sharp-force trauma in fresh and dry human bone under varied experimental heat conditions

Heat-induced fractures can be hard to distinguish from sharp force traumas. This challenge can negatively impact medico-legal analysis. The present study aimed to experimentally assess if X-ray fluorescence (XRF) can be used to detect chemical traces transferred from the blade of a sharp instrument onto both fresh and dry human bones. This was performed by inducing sharp force traumas with five different instruments on 20 fresh and 20 dry human clavicles. All bone samples were probed before and after experimental burning (at 500 °C, 700 °C, 900 °C and 1100 °C). Our results show that XRF is potentially useful for detecting iron traces in fresh human bone, both unburned and burned. However, we were not able to clearly detect iron traces from the blades in bones that have been previously inhumed, since exogenous iron acquired during diagenesis masks the iron traces originating from the blade.

Regeneration of alveolar bone defects in the experimental pig model: A systematic review and meta-analysis

OBJECTIVE

Pigs are emerging as a preferred experimental in vivo model for bone regeneration. The study objective was to answer the focused PEO question: in the pig model (P), what is the capacity of experimental alveolar bone defects (E) for spontaneous regeneration in terms of new bone formation (O)?

METHODS

Following PRISMA guidelines, electronic databases were searched for studies reporting experimental bone defects or extraction socket healing in the maxillae or mandibles of pigs. The main inclusion criteria were the presence of a control group of untreated defects/sockets and the assessment of regeneration via 3D tomography [radiographic defect fill (RDF)] or 2D histomorphometry [new bone formation (NBF)]. Random effects meta-analyses were performed for the outcomes RDF and NBF.

RESULTS

Overall, 45 studies were included reporting on alveolar bone defects or extraction sockets, most frequently in the mandibles of minipigs. Based on morphology, defects were broadly classified as 'box-defects' (BD) or 'cylinder-defects' (CD) with a wide range of healing times (10 days to 52 weeks). Meta-analyses revealed pooled estimates (with 95% confidence intervals) of 50% RDF (36.87%-63.15%) and 43.74% NBF (30.47%-57%) in BD, and 44% RDF (16.48%-71.61%) and 39.67% NBF (31.53%-47.81%) in CD, which were similar to estimates of socket-healing [48.74% RDF (40.35%-57.13%) and 38.73% NBF (28.57%-48.89%)]. Heterogeneity in the meta-analysis was high (I2 > 90%).

CONCLUSION

A substantial body of literature revealed a high capacity for spontaneous regeneration in experimental alveolar bone defects of (mini)pigs, which should be considered in future studies of bone regeneration in this animal model.

Enhanced Bone Healing in Critical-Sized Rabbit Femoral Defects: Impact of Helical and Alternate Scaffold Architectures

This study investigates the effect of scaffold architecture on bone regeneration, focusing on 3D-printed polylactic acid-bioceramic calcium phosphate (PLA-bioCaP) composite scaffolds in rabbit femoral condyle critical defects. We explored two distinct scaffold designs to assess their influence on bone healing and scaffold performance. Structures with alternate (0°/90°) and helical (0°/45°/90°/135°/180°) laydown patterns were manufactured with a 3D printer using a fused deposition modeling technique. The scaffolds were meticulously characterized for pore size, strut thickness, porosity, pore accessibility, and mechanical properties. The in vivo efficacy of these scaffolds was evaluated using a femoral condyle critical defect model in eight skeletally mature New Zealand White rabbits. Then, the results were analyzed micro-tomographically, histologically, and histomorphometrically. Our findings indicate that both scaffold architectures are biocompatible and support bone formation. The helical scaffolds, characterized by larger pore sizes and higher porosity, demonstrated significantly greater bone regeneration than the alternate structures. However, their lower mechanical strength presented limitations for use in load-bearing sites.

Animal Models for Investigating Osseointegration: An Overview of Implant Research over the Last Three Decades

Dental implants and bone augmentation are among dentistry's most prevalent surgical treatments; hence, many dental implant surfaces and bone grafts have been researched to improve bone response. Such new materials were radiologically, histologically, and histomorphometrically evaluated on animals before being used on humans. As a result, several studies used animals to evaluate novel implant technologies, biocompatibility, surgical techniques, and osseointegration strategies, as preclinical research on animal models is essential to evaluate bioactive principles (on cells, compounds, and implants) that can act through multiple mechanisms and to predict animal behavior, which is difficult to predict from in vitro studies alone. In this study, we critically reviewed all research on different animal models investigating the osseointegration degree of new implant surfaces, reporting different species used in the osseointegration research over the last 30 years. Moreover, this is the first study to summarize reviews on the main animal models used in the translational research of osseointegration, including the advantages and limitations of each model and determining the ideal location for investigating osseointegration in small and large animal models. Overall, each model has advantages and disadvantages; hence, animal selection should be based on the cost of acquisition, animal care, acceptability to society, availability, tolerance to captivity, and housing convenience. Among small animal models, rabbits are an ideal model for biological observations around implants, and it is worth noting that osseointegration was discovered in the rabbit model and successfully applied to humans.

Identification of temporal shifts of oral bacteria in bone regeneration following mandibular bone defect injury and therapeutic surgery in a porcine model

BACKGROUND

Considered the second largest and most diverse microbiome after the gut, the human oral ecosystem is complex with diverse and niche-specific microorganisms. Although evidence is growing for the importance of oral microbiome in supporting a healthy immune system and preventing local and systemic infections, the influence of craniomaxillofacial (CMF) trauma and routine reconstructive surgical treatments on community structure and function of oral resident microbes remains unknown. CMF injuries affect a large number of people, needing extensive rehabilitation with lasting morbidity and loss of human productivity. Treatment efficacy can be complicated by the overgrowth of opportunistic commensals or multidrug-resistant pathogens in the oral ecosystem due to weakened host immune function and reduced colonization resistance in a dysbiotic oral microbiome.

AIMS

To understand the dynamics of microbiota's community structure during CMF injury and subsequent treatments, we induced supra-alveolar mandibular defect in Hanford miniature swine (n = 3) and compared therapeutic approaches of immediate mandibullar reconstructive (IMR) versus delayed mandibullar reconstructive (DMR) surgeries.

METHODS

Using bacterial 16S ribosomal RNA gene marker sequencing, the composition and abundance of the bacterial community of the uninjured maxilla (control) and the injured left mandibula (lingual and buccal) treated by DMR were surveyed up to 70-day post-wounding. For the injured right mandibula receiving IMR treatment, the microbial composition and abundance were surveyed up to 14-day post-wounding. Moreover, we measured sera level of biochemical markers (e.g., osteocalcin) associated with bone regeneration and healing. Computed tomography was used to measure and compare mandibular bone characteristics such as trabecular thickness between sites receiving DMR and IMR therapeutic approaches until day 140, the end of study period.

RESULTS

Independent of IMR versus DMR therapy, we observed similar dysbiosis and shifts of the mucosal bacteria residents after CMF injury and/or following treatment. There was an enrichment of Fusobacterium, Porphyromonadaceae, and Bacteroidales accompanied by a decline in Pasteurellaceae, Moraxella, and Neisseria relative abundance in days allotted for healing. We also observed a decline in species richness and abundance driven by reduction in temporal instability and inter-animal heterogeneity on days 0 and 56, with day 0 corresponding to injury in DMR group and day 56 corresponding to delayed treatment for DMR or injury and immediate treatment for the IMR group. Analysis of bone healing features showed comparable bone-healing profiles for IMR vs. DMR therapeutic approach.

Effects of kinetic energy and firearm-to-target distance on fracture behavior in flat bones

This research implements a fractographic approach to investigate the relationships between kinetic energy, firearm-to-target distance, and various aspects of fracture behavior in gunshot trauma. Gunshot experiments were performed on pig scapulae (n = 30) using three firearms generating different muzzle (initial) kinetic energies, including a 0.32 pistol (103 J), 0.40 pistol (492 J), and 0.308 rifle (2275 J). Specimens were shot from two distances: 10 cm (n = 15) and 110 cm (n = 15). Features evaluated in fractographic analysis such as cone cracks, radiating cracks, crack branching points, and circumferential cracks could be easily identified and measured in flat bones and allowed for statistical comparison of crack propagation behavior under different impact conditions. Higher-energy bullets produced more radiating cracks, more crack branching points, and longer fracture lengths than lower-energy bullets. Distance had no significant effect on fracture morphology at the distances tested. That quantitative measures of crack propagation varied with energy affirms that kinetic energy transfer is important in determining the nature and extent of fracture in gunshot wounds and suggests it may be possible to infer relatively high- versus relatively low-energy transfer using these features. Ranges obtained with the three firearms exhibited considerable overlap, however, indicating that other variables such as bullet caliber, mass, and construction influence the efficiency of energy transfer from bullet to bone. Therefore, fracture morphology cannot be used to identify a specific firearm or to directly reconstruct the muzzle (initial) kinetic energy in forensic cases.

Improving bone defect healing using magnesium phosphate granules with tailored degradation characteristics

OBJECTIVES

Dental implant placement frequently requires preceding bone augmentation, for example, with hydroxyapatite (HA) or β-tricalcium phosphate (β-TCP) granules. However, HA is degraded very slowly in vivo and for β-TCP inconsistent degradation profiles from too rapid to rather slow are reported. To shorten the healing time before implant placement, rapidly resorbing synthetic materials are of great interest. In this study, we investigated the potential of magnesium phosphates in granular form as bone replacement materials.

METHODS

Spherical granules of four different materials were prepared via an emulsion process and investigated in trabecular bone defects in sheep: struvite (MgNH4PO4·6H2O), K-struvite (MgKPO4·6H2O), farringtonite (Mg3(PO4)2) and β-TCP.

RESULTS

All materials except K-struvite exhibited promising support of bone regeneration, biomechanical properties and degradation. Struvite and β-TCP granules degraded at a similar rate, with a relative granules area of 29% and 30% of the defect area 4 months after implantation, respectively, whereas 18% was found for farringtonite. Only the K-struvite granules degraded too rapidly, with a relative granules area of 2% remaining, resulting in initial fibrous tissue formation and intermediate impairment of biomechanical properties.

SIGNIFICANCE

We demonstrated that the magnesium phosphates struvite and farringtonite have a comparable or even improved degradation behavior in vivo compared to β-TCP. This emphasizes that magnesium phosphates may be a promising alternative to established calcium phosphate bone substitute materials.

Embracing ethical research: Implementing the 3R principles into fracture healing research for sustainable scientific progress

As scientific advancements continue to reshape the world, it becomes increasingly crucial to uphold ethical standards and minimize the potentially adverse impact of research activities. In this context, the implementation of the 3R principles-Replacement, Reduction, and Refinement-has emerged as a prominent framework for promoting ethical research practices in the use of animals. This article aims to explore recent advances in integrating the 3R principles into fracture healing research, highlighting their potential to enhance animal welfare, scientific validity, and societal trust. The review focuses on in vitro, in silico, ex vivo, and refined in vivo methods, which have the potential to replace, reduce, and refine animal experiments in musculoskeletal, bone, and fracture healing research. Here, we review material that was presented at the workshop "Implementing 3R Principles into Fracture Healing Research" at the 2023 Orthopedic Research Society (ORS) Annual Meeting in Dallas, Texas.

Artificial Intelligence-Based 3D Printing Strategies for Bone Scaffold Fabrication and Its Application in Preclinical and Clinical Investigations

3D printing has become increasingly popular in the field of bone tissue engineering. However, the mechanical properties, biocompatibility, and porosity of the 3D printed bone scaffolds are major requirements for tissue regeneration and implantation as well. Designing the scaffold architecture in accordance with the need to create better mechanical and biological stimuli is necessary to achieve unique scaffold properties. To accomplish this, different 3D designing strategies can be utilized with the help of the scaffold design library and artificial intelligence (AI). The implementation of AI to assist the 3D printing process can enable it to predict, adapt, and control the parameters on its own, which lowers the risk of errors. This Review emphasizes 3D design and fabrication of bone scaffold using different materials and the use of AI-aided 3D printing strategies. Also, the adaption of AI to 3D printing helps to develop patient-specific scaffolds based on different requirements, thus providing feedback and adequate data for reproducibility, which can be improvised in the future. These printed scaffolds can also serve as an alternative to preclinical animal test models to cut costs and prevent immunological interference.

In vivo behavior in rabbit radius bone defect of scaffolds based on nanocarbonate hydroxyapatite

Bone defects treatment may require the use of biomaterials that behave as a support and promote bone regeneration. Limitations associated with the use of autografts and allografts make it necessary to design new synthetic bone substitutes. Some of the most promising biomaterials currently under investigation are based on nanocarbonate hydroxyapatite (nCHA). In this study, we studied the bone-inducing capacity of nCHA-based scaffolds alone (SAG) and enriched with osteostatin (SAGO) or with bone marrow aspirate(SAGB) after implantation for 12 weeks in a 15-mm long critical defect performed in the radius of New Zealand rabbits. Bone formation obtained was compared with a group with the unfilled defect (CE), as control group, and other with the defect filed with iliac crest autograft (GS), as gold standard. X-ray follow-up was performed at 2, 4, 6 and 12 weeks and μCT and histological studies at 12 weeks. The radiological results showed a greater increment in bone formation in the GS group (75%-100%), followed by the SAG and SAGB groups (50%-75%). μCT results showed an increase of bone volume/tissue volume values in GS group followed by SAG and SAGB groups (0.53, 0.40, and 0.31 respectively) compared with CE group (0.26). Histological results showed limited resorption of the nCHA scaffolds and partial osseointegration in the SAG and SAGB groups. However, in the SAGO group, the presence of connective tissue encapsulating the scaffold was detected. In SAG, SAGB, and increase of bone formation were observed compared with CE group, but less than the GS group. Thus, the investigated materials represent a significant advance in the design of synthetic materials for bone grafting, but further studies are needed to bring their in vivo behavior closer to autograft, the gold standard.

Exploring the Use of Animal Models in Craniofacial Regenerative Medicine: A Narrative Review

The craniofacial region contains skin, bones, cartilage, the temporomandibular joint (TMJ), teeth, periodontal tissues, mucosa, salivary glands, muscles, nerves, and blood vessels. Applying tissue engineering therapeutically helps replace lost tissues after trauma or cancer. Despite recent advances, it remains essential to standardize and validate the most appropriate animal models to effectively translate preclinical data to clinical situations. Therefore, this review focused on applying various animal models in craniofacial tissue engineering and regeneration. This research was based on PubMed, Scopus, and Google Scholar data available until January 2023. This study included only English-language publications describing animal models' application in craniofacial tissue engineering (in vivo and review studies). Study selection was based on evaluating titles, abstracts, and full texts. The total number of initial studies was 6454. Following the screening process, 295 articles remained on the final list. Numerous in vivo studies have shown that small and large animal models can benefit clinical conditions by assessing the efficacy and safety of new therapeutic interventions, devices, and biomaterials in animals with similar diseases/defects to humans. Different species' anatomical, physiologic, and biological features must be considered in developing innovative, reproducible, and discriminative experimental models to select an appropriate animal model for a specific tissue defect. As a result, understanding the parallels between human and veterinary medicine can benefit both fields.

Influence of structural parameters of 3D-printed triply periodic minimal surface gyroid porous scaffolds on compression performance, cell response, and bone regeneration

In this study, multi-scale triply periodic minimal surface (TPMS) porous scaffolds with uniform and radial gradient distribution on pore size were printed based on the selective laser melting technology, and the influences of porosity, pore size and radial pore size distribution on compression mechanical properties, cell behavior, and bone regeneration behavior were analyzed. The results showed that the compression performance of the uniform porous scaffolds with high porosity was similar to that of cancellous bone of pig tibia, and the gradient porous scaffolds have higher elastic modulus and compressive toughness. After 4 days of cell culture, cells were distributed on the surface of scaffolds mostly, and the number of adherent cells was higher on the small pore size porous scaffolds; After 7 days, the area and density of cell proliferation on the scaffolds were improved; After 14 days, the cells on the small pore size scaffolds tended to migrate to adjacent pores. Animal implantation experiments showed that collagen fiber osteoid was intermittent on scaffolds with high porosity and large pore size, which was not conducive to bone formation. The appropriate pore size and porosity of bone regeneration were 792 um and 83%, respectively, and the regenerative ability of gradient pore size was better than that of uniform pore size. Our study explains the rules of TPMS gyroid structure parameters on compression performance, cell response and bone regeneration, and provides a reference value for the design of bone repair scaffolds for clinical orthopedics.

Bone Tissue Engineering (BTE) of the Craniofacial Skeleton, Part II: Translational Potential of 3D-Printed Scaffolds for Defect Repair

Computer-aided design/computer-aided manufacturing and 3-dimensional (3D) printing techniques have revolutionized the approach to bone tissue engineering for the repair of craniomaxillofacial skeletal defects. Ample research has been performed to gain a fundamental understanding of the optimal 3D-printed scaffold design and composition to facilitate appropriate bone formation and healing. Benchtop and preclinical, small animal model testing of 3D-printed bioactive ceramic scaffolds augmented with pharmacological/biological agents have yielded promising results given their potential combined osteogenic and osteoinductive capacity. However, other factors must be evaluated before newly developed constructs may be considered analogous alternatives to the "gold standard" autologous graft for defect repair. More specifically, the 3D-printed bioactive ceramic scaffold's long-term safety profile, biocompatibility, and resorption kinetics must be studied. The ultimate goal is to successfully regenerate bone that is comparable in volume, density, histologic composition, and mechanical strength to that of native bone. In vivo studies of these newly developed bone tissue engineering in translational animal models continue to make strides toward addressing regulatory and clinically relevant topics. These include the use of skeletally immature animal models to address the challenges posed by craniomaxillofacial defect repair in pediatric patients. This manuscript reviews the most recent preclinical animal studies seeking to assess 3D-printed ceramic scaffolds for improved repair of critical-sized craniofacial bony defects.

The effect of fibroblast growth factor-2 on the outcomes of tooth replantation: A systematic review of animal studies

Background/Aim: The ideal treatment of tooth avulsion is replantation. However, replanting teeth may lead to root resorption. Fibroblast growth factor-2 (FGF-2) is a cytokine that plays an important role in wound repair and tissue regeneration. Recently, FGF-2 has been studied a potential regenerative agent to prevent root resorption and ankylosis. The aim of this review is to analyze and summarize the currently available literature focusing on using FGF-2 based regenerative modalities to improve the outcomes of tooth replantation. Materials and Methods: An electronic search was conducted via PubMed/Medline, Google Scholar and ISI Web of Knowledge, using the Medical Subject Headings (MeSH) terms "Basic fibroblast growth factor," "Fibroblast growth factor-2," "tooth replantation," and "replantation" for studies published between January 2001 and June 2021. Data was extracted and quality assessment was carried using the ARRIVE guidelines. Results: Nine animal studies were included in this review. In six studies, FGF-2 had a favorable effect on the tissue regeneration around roots of replanted teeth when compared to other treatment groups. However, quality assessment of the studies revealed many sources of bias and deficiencies in the studies. Conclusions: Within the limitations of this study, it may be concluded that FGF-2 may improve the outcomes of delayed replantation of avulsed teeth. However, more long-term animal studies, with improved experimental designs, and clinical trials are required to determine the clinical potential of the growth factor in improving the outcomes of delayed tooth replantation.

Bone Regeneration in a Large Animal Model Featuring a Modular Off-the-Shelf Soft Callus Mimetic

Implantation of engineered cartilage with soft callus features triggers remodeling to bone tissue via endochondral bone regeneration (EBR). Thus far, EBR has not progressed to the level of large animals on the axis of clinical translation. Herein, the feasibility of EBR is aimed for a critical-sized defect in a large animal model. Chondrogenesis is first induced in goat-derived multipotent mesenchymal stromal cells (MSCs) by fine-tuning the cellular differentiation process. Through a unique devitalization process, two off-the-shelf constructs aimed to recapitulate the different stages of the transient cartilaginous soft callus template in EBR are generated. To evaluate bone regeneration, the materials are implanted in an adapted bilateral iliac crest defect model in goats, featuring a novel titanium star-shaped spacer. After 3 months, the group at the more advanced differentiation stage shows remarkable regenerative capacity, with comparable amounts of bone regeneration as the autograft group. In contrast, while the biomaterial mimicking the earlier stages of chondrogenesis shows improved regeneration compared to the negative controls, this is subpar compared to the more advanced material. Concluding, EBR is attainable in large animals with a soft callus mimetic material that leads to fast conversion into centimeter-scale bone, which prospects successful implementation in the human clinics.

Characterization of rat vertebrae cortical bone microstructures using confocal Raman microscopy combined to tomography and electron microscopy

BACKGROUND

The rat vertebrae is a good model to study bone regeneration after implantation of biomaterials used to treat bone loss, a major problem in oral and dental surgery. However, the precise characterization of bone microstructures in the rat vertebrae has not been reported. Therefore, the aim of this study was to achieve the complete analysis of such bone, at different scales, in order to have a clear model of healthy bone for comparison with regenerated bone.

METHODS

In order to image the cortical bone of rat caudal vertebra, confocal Raman microscopy was combined with high resolution X-ray micro computed tomography (micro-CT), with scanning electron microscopy (SEM) using backscatter electron imaging and with more conventional histology coloration techniques. SEM and Raman microscopy were done in various regions of the cortical bone corresponding to external, middle and internal areas. The spongy bone was imaged in parallel. Micro-CT was performed on the whole vertebra to monitor the network of haversian canals in the cortical bone. Osteonic canals characteristics, and relative chemical composition were analysed in several regions of interest, in cortical and spongy bone. Five rats were included in this study.

RESULTS

On micro-CT images, differences in intensity were observed in the cortical bone, substantiated by SEM. Chemical analysis with Raman spectra confirmed the difference in composition between the different regions of the cortical and spongy bone. PCA and k-mean cluster analysis separated these groups, except for the external and middle cortical bone. Peak intensity ratio confirmed these results with a CO3 to ν2 PO4 ratio significantly different for the internal cortical bone. Grayscale images stack extracted from micro-CT showed that global architecture of cortical bone was characterized by a dense and complex network of haversian osteonic canals, starting from the surface towards the vertebrae center. The mean diameter of the canals was 18.4 µm (SD 8.6 µm) and the mean length was 450 µm (SD 152 µm). Finally, Raman reconstructed images of the lamellar bone showed an enlargement of the lamellar layer width, both in circumferential lamellar bone and around haversian canals.

CONCLUSIONS

Micro-CT and confocal Raman microscopy are good tools to complete classical analysis using optical and electron microscopy. The results and measurements presented in a rat model known for its small inter-individual differences provide the main characteristics of a mature bone. This study will allow the community working on this rat vertebrate model to have a set of characteristics, in particular on the structure of the haversian canals.

Cortical bone microdamage affects primary stability of orthodontic miniscrew

BACKGROUND

The aim of this study was to investigate the effects of orthodontic miniscrew pitch and thread shape on microdamage in cortical bone. The relationship between the microdamage and primary stability was also examined.

METHODS

Ti6Al4V orthodontic miniscrews and 1.0-mm-thick cortical bone pieces from fresh porcine tibia were prepared. The orthodontic miniscrews had custom-made thread height (H) and pitch (P) size geometries, and were classified into three groups: control geometry; HCPC (HC; thread height = 0.12 mm, PC; pitch size = 0.60 mm), geometry with a narrower pitch; HCPN (HC; thread height = 0.12 mm, PN; pitch size = 0.30 mm), and geometry with a taller thread height; HTPC (HT; thread height = 0.36 mm, PC; pitch size = 0.60 mm). The orthodontic miniscrews were inserted into a pilot hole in the cortical bone, and maximum insertion torque and Periotest value were measured. After insertion, the samples were stained with basic fuchsin. Histological thin sections were obtained and the bone microdamage parameters, i.e., total crack length and total damage area, and insertion state parameters, i.e., orthodontic miniscrew surface length and bone compression area were calculated.

RESULTS

The orthodontic miniscrews with the taller thread height resulted in lower primary stability with minimal bone compression and microdamage; however, the narrower thread pitch led to maximum bone compression and extensive bone microdamage.

CONCLUSIONS

A wider thread pitch reduced microdamage, and decreased thread height resulted in increased bone compression, ultimately resulting in increased primary stability.

Evaluation of Vitamin D-enriched Bone Graft in Surgically-induced Critical-sized Bone Defects: An Experimental Study

BACKGROUND

Restoration of bone defects in the craniac vault may require the use of autografts, allografts, xenografts, or synthetic grafts. There are promising data that vitamin D may play a positive role in graft incorporation. The purpose of the present study is the evaluation of the impact of vitamin D addition to human-derived bone grafts in the healing of critical-sized bone defects in porcine skulls.

MATERIALS AND METHODS

Four identical critical-sized defects were created in the calvaria of 8 adult Landrace Large White pigs. The first defect was left blank as control, the second defect was filled with human-derived bone graft, the third defect was filled with human-derived bone graft enriched with a low concentration of vitamin D (2 mg/mL), and the fourth defect was filled with human-derived bone graft enriched with a high concentration of vitamin D (10 mg/mL). The animals were sacrificed after 12 weeks. Harvested tissue specimens were qualitatively evaluated by histology. New bone formation (bone volume/tissue volume) was quantitatively measured by histomorphometry.

RESULTS

Signs of bone formation were evident in all bone sockets. Mean values of the bone volume/tissue volume of the 4 defects were 10.91%, 11.05%, 10.40% and 10.87% respectively, at 12 weeks. In 5 animals, high concentration of vitamin D caused a significant improvement in bone formation in relation to controls. In 3 animals, a high concentration of vitamin D was associated with decreased bone formation compared with controls. No statistical difference was observed in the graft healing among the 4 graft sites ( P > 0.05).

CONCLUSIONS

The results of this study have shown that the addition of vitamin D to human-derived bone grafts does not have a significant effect on bone formation and graft incorporation in critical-sized bone defects of the porcine calvaria. Further high-quality studies are needed to fully elucidate the role of vitamin D in bone formation and bone graft union.

A proposed method for differentiating knives from cut marks on bone: A forensic anthropological approach

Knife cut marks have been extensively studied in forensic literature, and the results have been beneficial in identifying both the cut mark and implement type on bone. For this study, an assessment in differentiating knife cut marks has been attempted by using sword cut mark characteristics. In addition, a flowchart was created to assist in interpreting such marks. Knives of different serrations (non-serrated, macro- and micro-serrated) were used to inflict cut marks on pig ribs with a forward and backward stab thrust. The analysis revealed that some traits adapted from previous studies applied to knife cut marks and that non-serrated and serrated marks could be distinguished accurately using the flowchart. The distinction between different types of serrated blades was not as successful. However, results show that further research and development of the flowchart can be invaluable in similar analyses.

Aerogel-Based Materials in Bone and Cartilage Tissue Engineering-A Review with Future Implications

Aerogels are fascinating solid materials known for their highly porous nanostructure and exceptional physical, chemical, and mechanical properties. They show great promise in various technological and biomedical applications, including tissue engineering, and bone and cartilage substitution. To evaluate the bioactivity of bone substitutes, researchers typically conduct in vitro tests using simulated body fluids and specific cell lines, while in vivo testing involves the study of materials in different animal species. In this context, our primary focus is to investigate the applications of different types of aerogels, considering their specific materials, microstructure, and porosity in the field of bone and cartilage tissue engineering. From clinically approved materials to experimental aerogels, we present a comprehensive list and summary of various aerogel building blocks and their biological activities. Additionally, we explore how the complexity of aerogel scaffolds influences their in vivo performance, ranging from simple single-component or hybrid aerogels to more intricate and organized structures. We also discuss commonly used formulation and drying methods in aerogel chemistry, including molding, freeze casting, supercritical foaming, freeze drying, subcritical, and supercritical drying techniques. These techniques play a crucial role in shaping aerogels for specific applications. Alongside the progress made, we acknowledge the challenges ahead and assess the near and far future of aerogel-based hard tissue engineering materials, as well as their potential connection with emerging healing techniques.

Optimized osteogenesis of porcine bone-derived xenograft through surface coating of magnesium-doped nanohydroxyapatite

As one of the key factors influencing the outcome of guided bone regeneration, the currently used xenografts possess insufficient capability in osteogenesis. With the aim of improving the osteogenic performance of xenografts, porcine bone-derived hydroxyapatite (PHA) was prepared and subsequently coated by magnesium-doped nano hydroxyapatite (nMgHA, 10%, 20%, and 30% of Mg/Ca + Mg) through a straightforward and cost-efficient approach. The physiochemical and biological properties of nMgHA/PHAs were examinedin vitroandin vivo. The inherent three-dimensional (3D) porous framework with the average pore size of 300 μm was well preserved in nMgHA/PHAs. Meanwhile, excess magnesium released from the so-called 'surface pool' of PHA was verified. In contrast, slower release of magnesium at lower concentrations was detected for nMgHA/PHAs. Significantly more newly-formed bone and microvessels were observed in 20%nMgHA/PHA than the other specimens. With the limitations of the present study, it could be concluded that PHA coated by 20%nMgHA may have the optimized osteogenic performance due to the elimination of the excess magnesium from the 'surface pool', the preservation of the inherent 3D porous framework with the favorable pore size, and the release of magnesium at an appropriate concentration that possessed osteoimmunomodulatory effects on macrophages.

Comparison of the 3D-microstructure of human alveolar and fibula bone in microvascular autologous bone transplantation: a synchrotron radiation μ-CT study

Introduction: Autologous bone transplantation is successfully used in reconstructive surgery of large/critical-sized bone defects, whereby the microvascular free fibula flap is still regarded as the gold standard for the reconstruction of such defects in the head and neck region. Here, we report the morphological and lacunar properties of patient-paired bone samples from eight patients from the jaw (AB; recipient site) and the fibula (FB; donor site) on the micron length-scale using Synchrotron µ-CT. Insights into differences and similarities between these bone structures could offer a better understanding of the underlying mechanism for successful surgical outcomes and might clear the path for optimized, nature-inspired bone scaffold designs. Methods: Spatial vessel-pore arrangements, bone morphology, fluid-simulation derived permeability tensor, osteocyte lacunar density, and lacunar morphology are compared. Results: The orientation of the vessel system indicates a homogenous vessel orientation for AB and FB. The average mineral distance (50%) to the closest vessel boundary is higher in AB than in FB (the mean is 96 μm for AB vs. 76 μm for FB; p = 0.021). Average osteocyte lacunar density is found to be higher in AB than in FB (mean 22,874 mm3 vs. 19,376 mm3 for FB; p = 0.038), which might compensate for the high distance from the mineral to the nearest vessel. No significant differences in lacunar volume are found between paired AB and FB. Discussion: A comparable vessel network and similar distribution of vessel porosity between AB and FB may allow the FB graft to exhibit a high regeneration potential when connected to AB, and this might correlate with a high osteoinductive and osteoconductive potential of FB when connected to AB. Since widely used and potent synthetic bone grafts exist, new insight into the bone structure of well-established autologous bone grafts, such as the free fibula flap, could help to improve the performance of such materials and therefore the design of 3D scaffolds.

Thickness of simple calcaneal tuberosity avulsion fractures influences the optimal fixation method employed

Aims

This study aimed to establish the optimal fixation methods for calcaneal tuberosity avulsion fractures with different fragment thicknesses in a porcine model.

Methods

A total of 36 porcine calcanea were sawed to create simple avulsion fractures with three different fragment thicknesses (5, 10, and 15 mm). They were randomly fixed with either two suture anchors or one headless screw. Load-to-failure and cyclic loading tension tests were performed for the biomechanical analysis.

Results

This biomechanical study predicts that headless screw fixation is a better option if fragment thickness is over 15 mm in terms of the comparable peak failure load to suture anchor fixation (headless screw: 432.55 N (SD 62.25); suture anchor: 446.58 N (SD 84.97)), and less fracture fragment displacement after cyclic loading (headless screw: 3.94 N (SD 1.76); suture anchor: 8.68 N (SD 1.84)). Given that the fragment thickness is less than 10 mm, suture anchor fixation is a safer option.

Conclusion

Fracture fragment thickness helps in making the decision of either using headless screw or suture anchor fixation in treating calcaneal tuberosity avulsion fracture, based on the regression models of our study.

In-vivo evaluations of bone regenerative potential of two novel bioactive glasses

Due to the aging of population, materials able to repair damaged tissues are needed. Among others, bioactive glasses (BGs) have attracted a lot of interest due to their outstanding properties both for hard and soft tissues. Here, for the first time, two new BGs, which gave very promising results in preliminary in vitro-tests, were implanted in animals in order to evaluate their regenerative potential. The new BGs, named BGMS10 and Bio_MS and containing specific therapeutic ions, were produced in granules and implanted in rabbits' femurs for up to 60 days, to test their biocompatibility and osteoconduction. Additionally, granules of 45S5 Bioglass® were employed and used as a standard reference for comparison. The results showed that, after 30 days, the two novel BGs and 45S5 displayed a similar behavior, in terms of bone amount, thickness of new bone trabeculae and affinity index. On the contrary, after 60 days, 45S5 granules were mainly surrounded by wide and scattered bone trabeculae, separated by large amounts of soft tissue, while in BGMS10 and Bio_MS the trabeculae were thin and uniformly distributed around the BG granules. This latter scenario could be considered as more advantageous, since the features of the two novel BG granules allowed for the neo-formation of a uniformly distributed bony trabeculae, predictive of more favorable mechanical behavior, compared to the less uniform coarse trabeculae, separated by large areas of soft tissue in 45S5 granules. Thus, BGMS10 and Bio_MS could be considered suitable products for tissue regeneration in the orthopedic and dental fields.

Why Animal Experiments Are Still Indispensable in Bone Research: A Statement by the European Calcified Tissue Society

Major achievements in bone research have always relied on animal models and in vitro systems derived from patient and animal material. However, the use of animals in research has drawn intense ethical debate and the complete abolition of animal experimentation is demanded by fractions of the population. This phenomenon is enhanced by the reproducibility crisis in science and the advance of in vitro and in silico techniques. 3D culture, organ-on-a-chip, and computer models have improved enormously over the last few years. Nevertheless, the overall complexity of bone tissue cross-talk and the systemic and local regulation of bone physiology can often only be addressed in entire vertebrates. Powerful genetic methods such as conditional mutagenesis, lineage tracing, and modeling of the diseases enhanced the understanding of the entire skeletal system. In this review endorsed by the European Calcified Tissue Society (ECTS), a working group of investigators from Europe and the US provides an overview of the strengths and limitations of experimental animal models, including rodents, fish, and large animals, as well the potential and shortcomings of in vitro and in silico technologies in skeletal research. We propose that the proper combination of the right animal model for a specific hypothesis and state-of-the-art in vitro and/or in silico technology is essential to solving remaining important questions in bone research. This is crucial for executing most efficiently the 3R principles to reduce, refine, and replace animal experimentation, for enhancing our knowledge of skeletal biology, and for the treatment of bone diseases that affect a large part of society. © 2023 The Authors. Journal of Bone and Mineral Research published by Wiley Periodicals LLC on behalf of American Society for Bone and Mineral Research (ASBMR).

Anatomical characterization of the intraosseous arteries of the porcine tibia

Introduction

Tibial fractures have a high rate of post-fracture complications. Blood supply is recognized as a positive factor in tibial fracture healing. However, it's difficult to assess blood supply damage after tibial fracture because of the lack of understanding of the tibial intraosseous arteries. This study aimed to delineate and anatomically characterize porcine tibial intraosseous arteries, as a model for the human system.

Methods

Twenty right calf specimens with popliteal vessels were prepared from ordinary Landrace pigs. Epoxy resin was perfused into the vasculature from the popliteal artery. After 24 h, casts of the intraosseous arteries of the tibia were exposed through acid and alkali corrosion. The distribution and anatomy of the exposed intraosseous arteries were observed and measured under a microscope, and the data were statistically analyzed.

Results

Sixteen complete specimens were obtained. The medullary artery bifurcated into the main ascending and descending branches, which each split into two upward primary branches that further divided into 1-3 secondary branches. Among all specimens, 56 ascending and 42 descending secondary branches, which were all ≥0.3 mm in diameter. Furthermore, the horizontal plane was divided into three zones-safety, buffer, and danger zones-according to the probability of the presence of intraosseous artery.

Discussion

The cast perfusion and corrosion approach was successfully applied for anatomical characterization of the intraosseous arteries of the porcine tibia. These observations provide a theoretical basis for understanding the tibial vasculature in humans and will facilitate the establishment of novel "safe corridor" in the tibia for the protection of the blood supply during surgery.

Range of motion of the mid-cervical spine: human versus goat

BACKGROUND

The goat cervical spine represents a promising alternative for human specimen in spinal implant testing, but the range of motion (ROM) of the spine is lacking. We aimed to evaluate and compare the ROMs of fresh goat and human mid-cervical spine specimens.

METHODS

Ten fresh adult healthy male goat cervical spine specimens (G group) and ten fresh frozen adult healthy human cervical spine specimens (average age: 49.5 ± 12.1 years; 6 males, 4 females) (H group) were included. The ROMs of each specimen were biomechanically tested at the C_2-3, C_3-4, C_4-5 and C_2-5 levels at 1.5 Nm and 2.5 Nm torque and recorded. The ROMs of different levels of goat cervical samples were compared to those of human cervical samples using an independent sample t test. Significance was defined as a P value of less than 0.05.

RESULTS

At the C_2-3, C_3-4 and C_4-5 levels, the ROMs of the goat cervical spine were significantly larger than those of the human cervical spine in all directions except extension under 1.5 Nm torque; under 2.5 Nm torque, the ROMs of the goat cervical spine at the C_2-3 and C_3-4 levels were significantly larger than those of humans in the pure movement of flexion, lateral bending and axial rotation, and the ROMs for axial rotation of the goat specimens and human specimens were comparable. Under both 1.5 Nm and 2.5 Nm torque, the goat cervical spine displayed a much greater ROM in all directions at the C_2-5 level.

CONCLUSIONS

Several segmental ROMs of fresh goat and human cervical spine specimens were recorded in this investigation. We recommend using goat cervical specimens as an alternative to fresh human cervical specimens in future studies when focusing only on the ROMs of C_2-3, C_3-4 and C_4-5 in flexion under a torque of 1.5 Nm or the ROMs of C_2-3 and C_3-4 in flexion and rotation under a torque of 2.5 Nm.

Bone Grafts in Dental Medicine: An Overview of Autografts, Allografts and Synthetic Materials

This review provides an overview of various materials used in dentistry and oral and maxillofacial surgeries to replace or repair bone defects. The choice of material depends on factors such as tissue viability, size, shape, and defect volume. While small bone defects can regenerate naturally, extensive defects or loss or pathological fractures require surgical intervention and the use of substitute bones. Autologous bone, taken from the patient's own body, is the gold standard for bone grafting but has drawbacks such as uncertain prognosis, surgery at the donor site, and limited availability. Other alternatives for medium and small-sized defects include allografts (from human donors), xenografts (from animals), and synthetic materials with osteoconductive properties. Allografts are carefully selected and processed human bone materials, while xenografts are derived from animals and possess similar chemical composition to human bone. Synthetic materials such as ceramics and bioactive glasses are used for small defects but may lack osteoinductivity and moldability. Calcium-phosphate-based ceramics, particularly hydroxyapatite, are extensively studied and commonly used due to their compositional similarity to natural bone. Additional components, such as growth factors, autogenous bone, and therapeutic elements, can be incorporated into synthetic or xenogeneic scaffolds to enhance their osteogenic properties. This review aims to provide a comprehensive analysis of grafting materials in dentistry, discussing their properties, advantages, and disadvantages. It also highlights the challenges of analyzing in vivo and clinical studies to select the most suitable option for specific situations.

Comparative Analysis of Bone Ingrowth in 3D-Printed Titanium Lattice Structures with Different Patterns

In this study, metal 3D printing technology was used to create lattice-shaped test specimens of orthopedic implants to determine the effect of different lattice shapes on bone ingrowth. Six different lattice shapes were used: gyroid, cube, cylinder, tetrahedron, double pyramid, and Voronoi. The lattice-structured implants were produced from Ti6Al4V alloy using direct metal laser sintering 3D printing technology with an EOS M290 printer. The implants were implanted into the femoral condyles of sheep, and the animals were euthanized 8 and 12 weeks after surgery. To determine the degree of bone ingrowth for different lattice-shaped implants, mechanical, histological, and image processing tests on ground samples and optical microscopic images were performed. In the mechanical test, the force required to compress the different lattice-shaped implants and the force required for a solid implant were compared, and significant differences were found in several instances. Statistically evaluating the results of our image processing algorithm, it was found that the digitally segmented areas clearly consisted of ingrown bone tissue; this finding is also supported by the results of classical histological processing. Our main goal was realized, so the bone ingrowth efficiencies of the six lattice shapes were ranked. It was found that the gyroid, double pyramid, and cube-shaped lattice implants had the highest degree of bone tissue growth per unit time. This ranking of the three lattice shapes remained the same at both 8 and 12 weeks after euthanasia. In accordance with the study, as a side project, a new image processing algorithm was developed that proved suitable for determining the degree of bone ingrowth in lattice implants from optical microscopic images. Along with the cube lattice shape, whose high bone ingrowth values have been previously reported in many studies, it was found that the gyroid and double pyramid lattice shapes produced similarly good results.

Evaluation of Two Configurations of Hydroxyapatite and Beta-Tricalcium Phosphate in Sinus Grafts with Simultaneous Implant Installation: An Experimental Study in Rabbits

BACKGROUND

This study aimed to evaluate peri-implant bone formation in rabbits after sinus grafting mediated by hydroxyapatite and beta-tricalcium phosphate (HA + β-TCP) in granule or paste configurations, concomitant with immediate implant installation.

MATERIAL & METHODS

Thirty-four rabbit maxillary sinuses were grafted with HA + β-TCP, half of which were applied in a granule and half in a paste composition. Implant placement was performed simultaneously. At 7 and 40 days postoperatively, the animals were euthanized, and samples were prepared for tomographic, microtomographic, histological, histometric (hematoxylin and eosin staining, HE), and immunohistochemical (labeling of transcription factor Runx-2 [RUNX2], vascular endothelial growth factor [VEGF], osteocalcin [OCN], and tartrate-resistant acid phosphatase [TRAP]) analysis. Implant removal torque was also measured.

RESULTS

On tomography, maintenance of sinus membrane integrity was observed in both the groups. Higher values of morphometric parameters evaluated by micro-CT were found in the "paste group" after seven days. At 40 days, there were no significant differences between the groups in most of the microtomographic parameters evaluated. In histological sections stained with HE, a higher percentage of newly formed bone was observed in the "granule group" after 40 days. Similar positive immunolabeling was observed for both RUNX2 and OCN in both the experimental groups. TRAP immunolabeling was similar in both groups as well. VEGF labeling increased in the "granule group", indicating a higher osteoconductive potential in this biomaterial. Similar removal torque values were observed in both groups. Thus, the two HA + β-TCP configurations showed similar healing patterns of simultaneously installed implants adjacent to sinus floor elevation. However, significantly higher bone values were observed for the "granule configuration".

CONCLUSIONS

The HA + β-TCP granules and paste presentations showed favorable long-term healing results, with bone formation in similar quantities and quality adjacent to the implants.

Lateral Bone Augmentation Using a 3D-printed Polymeric Chamber to compare biomaterials

The aim of this study was to test the suitability of calcium phosphate cement mixed with poly(lactic-co-glycolic acid microparticles (CPC-PLGA) into a ring-shaped polymeric space-maintaining device as bone graft material for lateral bone augmentation. Therefore, the bone chambers were installed on the lateral portion of the anterior region of the mandibular body of mini-pigs. Chambers were filled with either calcium phosphate cement mixed with poly(lactic-co-glycolic acid microparticles (CPC-PLGA) or BioOss® particles for comparison and left for 4 and 12 weeks. Histology and histomorphometry were used to obtain temporal insight in material degradation and bone formation. Results indicated that between 4 and 12 weeks of implantation, a significant degradation of the CPC-PLGA (from 75.1% to 23.1%) as well as BioOss® material occurred (from 40.6% to 14.4%). Degradation of both materials was associated with the presence of macrophage-like and osteoclast-like cells. Further, a significant increase in bone formation occurred between 4 and 12 weeks for the CPC-PLGA (from 0.1% to 7.2%) as well as BioOss® material (from 8.3% to 23.3%). Statistical analysis showed that bone formation had progressed significantly better using BioOss® compared to CPC-PLGA (p<0.05). In conclusion, this mini-pig study showed that CPC-PLGA does not stimulate lateral bone augmentation using a bone chamber device. Both treatments failed to achieve "clinically" meaningful alveolar ridge augmentation.

A porcine model of early-onset scoliosis combined with thoracic insufficiency syndrome: Construction and transcriptome analysis

BACKGROUND

Early-onset scoliosis (EOS) is a scoliosis deformity caused by various reasons before the age of 10 years and is often combined with thoracic insufficiency syndrome (TIS) causing patients with difficulty in securing lung growth in the thoracic cage. Currently, there is a shortage of effective large animal models for evaluating EOS + TIS in therapeutic studies. Consequently, we propose to construct a porcine EOS + TIS model and evaluate its transcriptome changes by RNA sequencing.

METHODS

Piglets were constructed using unilateral posterior spine-tethering and ipsilateral rib-tethering in the EOS + TIS model, and X-ray and computed tomography (CT) were performed to assess growth changes in the spine, thoracic cage and lungs. The H&E and Masson staining was performed for pathological analysis of lung tissue. After RNA sequencing of lung tissues, data were analyzed for differential expression of mRNA, functional enrichment analysis (GO, KEGG and GSEA) and protein-protein interaction (PPI) network construction, and differential expression of hub gene was verified by RT-qPCR.

RESULTS

In the model group, growth (body weight and length) of piglets was significantly delayed; fusion of ribs occurred and cobb angle changes in the coronal and sagittal planes were significantly enlarged; total lung volume (TLV) was significantly reduced, especially at the T7-T10 level. Pathological analysis revealed that, in the model lung tissue, the alveolar wall of was poorly perfused, the alveolar space was enlarged, the number and size of alveoli were significantly reduced, and it was accompanied by collagen fiber deposition. Moreover, a total of 432 differentially expressed mRNAs (DE-mRNAs) were identified in model lung tissues, which contained 262 down-regulated and 170 up-regulated DE-mRNAs, and they were mainly involved in the regulation of immunity, inflammation, cell cycle and extracellular matrix. A PPI network containing 71 nodes and 158 edges was constructed based on all DE-mRNAs, and JUN, CCL2, EGR1, ATF3, BTG2, DUSP1 and THBS1 etc. were hub gene.

CONCLUSIONS

Overall, we constructed a porcine model that was capable of replicating the common clinical features of EOS + TIS such as rib fusion, asymmetric thoracic cage, increased cobb angle, decreased TLV, and pulmonary hypoplasia. Also, we revealed transcriptomic changes in the EOS + TIS model that may cause pulmonary hypoplasia.

Histological and Histomorphometric Evaluation of Implanted Photodynamic Active Biomaterials for Periodontal Bone Regeneration in an Animal Study

Recently, our group developed two different polymeric biomaterials with photodynamic antimicrobial surface activity for periodontal bone regeneration. The aim of the present study was to analyze the biocompatibility and osseointegration of these materials in vivo. Two biomaterials based on urethane dimethacrylate (BioM1) and tri-armed oligoester-urethane methacrylate (BioM2) that additionally contained ß-tricalcium phosphate and the photosensitizer mTHPC (meso-tetra(hydroxyphenyl)chlorin) were implanted in non-critical size bone defects in the femur (n = 16) and tibia (n = 8) of eight female domestic sheep. Bone specimens were harvested and histomorphometrically analyzed after 12 months. BioM1 degraded to a lower extent which resulted in a mean remnant square size of 17.4 mm², while 12.2 mm² was estimated for BioM2 (p = 0.007). For BioM1, a total percentage of new formed bone by 30.3% was found which was significant higher compared to BioM2 (8.4%, p < 0.001). Furthermore, BioM1 was afflicted by significant lower soft tissue formation (3.3%) as compared to BioM2 (29.5%). Additionally, a bone-to-biomaterial ratio of 81.9% was detected for BioM1, while 8.5% was recorded for BioM2. Implantation of BioM2 caused accumulation of inflammatory cells and led to fibrous encapsulation. BioM1 (photosensitizer-armed urethane dimethacrylate) showed favorable regenerative characteristics and can be recommended for further studies.

Finite Element Analysis of Different Osseocartilaginous Reconstruction Techniques in Animal Model Knees

Lesions of the articular cartilage are frequent in all age populations and lead to functional impairment. Multiple surgical techniques have failed to provide an effective method for cartilage repair. The aim of our research was to evaluate the effect of two different compression forces on three types of cartilage repair using finite element analysis (FEA). Initially, an in vivo study was performed on sheep. The in vivo study was prepared as following: Case 0-control group, without cartilage lesion; Case 1-cartilage lesion treated with macro-porous collagen implants; Case 2-cartilage lesion treated with collagen implants impregnated with bone marrow concentrate (BMC); Case 3-cartilage lesion treated with collagen implants impregnated with adipose-derived stem cells (ASC). Using the computed tomography (CT) data, virtual femur-cartilage-tibia joints were created for each Case. The study showed better results in bone changes when using porous collagen implants impregnated with BMC or ASC stem cells for the treatment of osseocartilaginous defects compared with untreated macro-porous implant. After 7 months postoperative, the presence of un-resorbed collagen influences the von Mises stress distribution, total deformation, and displacement on the Z axis. The BMC treatment was superior to ASC cells in bone tissue morphology, resembling the biomechanics of the control group in all FEA simulations.

Local Antibiotic Delivery Ceramic Bone Substitutes for the Treatment of Infected Bone Cavities and Bone Regeneration: A Systematic Review on What We Have Learned from Animal Models

AIMS

the focus of this study is to evaluate if the combination of an antibiotic with a ceramic biomaterial is effective in treating osteomyelitis in an infected animal model and to define which model and protocol are best suited for in vivo experiments of local bone infection treatment.

METHODS

a systematic review was carried out based on PRISMA statement guidelines. A PubMed search was conducted to find original papers on animal models of bone infections using local antibiotic delivery systems with the characteristics of bone substitutes. Articles without a control group, differing from the experimental group only by the addition of antibiotics to the bone substitute, were excluded.

RESULTS

a total of 1185 records were retrieved, and after a three-step selection, 34 papers were included. Six manuscripts studied the effect of antibiotic-loaded biomaterials on bone infection prevention. Five articles studied infection in the presence of foreign bodies. In all but one, the combination of an antibiotic with bioceramic bone substitutes tended to prevent or cure bone infection while promoting biomaterial osteointegration.

CONCLUSIONS

this systematic review shows that the combination of antibiotics with bioceramic bone substitutes may be appropriate to treat bone infection when applied locally. The variability of the animal models, time to develop an infection, antibiotic used, way of carrying and releasing antibiotics, type of ceramic material, and endpoints limits the conclusions on the ideal therapy, enhancing the need for consistent models and guidelines to develop an adequate combination of material and antimicrobial agent leading to an effective human application.

Electric/Magnetic Intervention for Bone Regeneration: A Systematic Review and Network Meta-Analysis

Electric/magnetic material or field is a promising strategy for bone regeneration. The aim of this systematic review and network meta-analysis was to analyze the evidence regarding the efficacy of electric and magnetic intervention for bone regeneration and provide directions for further research. A comprehensive search was performed to identify the rats/rabbits/mice research that involved the electric/magnetic treatment with quantitative radiographic assessment of bone formation. Network meta-analyses were also conducted to assess different interventions and outcomes for osteogenesis. In total, there were 51 articles included in the systematic review and 19 articles in the network meta-analyses. The majority used microcomputerized tomography bone volume/tissue volume (BV/TV) to evaluate outcomes in rats. Results showed that placing electric/magnetic materials in situ had more prominent effects than the electric/magnetic field on bone regeneration. For all species, electrical materials with zeta potential of -53 mV proved to be the most effective in increasing BV (mean difference [MD]: 4.20 mm³, 95% confidence interval [CI]: [1.72-6.68]) and bone mineral density (MD: 312 mg/cm³, 95% CI: [172.43-451.57]). Magnetic materials with external magnetic fields topped in BV/TV (MD: 43%, 95% CI: [36.04-49.96]). It also led in trabecular number (MD: 2.00 mm^-1, 95% CI: [1.45-2.55]), trabecular thickness (MD: 61.00 μm, 95% CI: [44.31- 77.69]), and trabecular separation (MD: -0.40 mm, 95% CI: [-0.56 to -0.24]) on the condition of lacking electric materials. Biomaterials implantation is the most effective method for stimulating osteogenesis in rats, especially in electrical materials with negative charge. The combination of diverse interventions shows promising effects but needs further research, so does the underlying mechanism. Impact Statement Bone defect, especially for the large defect from aging, trauma, or pathology, which cannot be completely healed, remains a clinical challenge. Mimicking physical microenvironment has emerged as a new strategy for tissue regeneration. Electric and magnetic material and field used as the physical stimulation for bone regeneration have attracted interest due to their potential and facile application in clinic. This article reviewed related animal studies and carried out a network meta-analysis to thoroughly understand how electric and magnetic interventions impacted on tissues and created an osteogenic microenvironment.

Biomechanical Comparison of 5 Different Fixation Constructs in a Trapeziometacarpal Joint Arthrodesis Model

PURPOSE

Trapeziometacarpal joint (TMC) arthrodesis has a high rate of nonunion. This biomechanical analysis sought to determine the stiffness of 5 fixation methods in a TMC joint arthrodesis model.

METHODS

Five fixation constructs were tested in a validated porcine model: crossed 1.1-mm K-wires, crossed 1.6-mm K-wires, crossed headless compression screws (HCSs), compression plating (CP), and locked compression plating (LCP). The cantilever bending stiffness was measured in abduction, adduction, flexion, and extension. Samples were loaded to failure in extension, and the mode of failure was examined.

RESULTS

The crossed HCSs performed consistently well in all tests. Loading to failure resulted in screw pullout. In abduction and adduction, HCS and 1.6-mm K-wires were significantly stiffer than the other constructs. The mean load to failure in extension was similar in the HCS, CP, and LCP groups (304 N/mm, 311 N/mm, and 293 N/mm, respectively). There were no differences between CP and LCP in any biomechanical tests, and the mode of failure was through plate bending. The crossed 1.1-mm K-wires performed poorly in all tests.

CONCLUSIONS

Crossed HCS displayed the greatest overall stability. Standard plating in compression mode and LCP had a similar biomechanical performance.

CLINICAL RELEVANCE

The ideal construct stiffness required for the successful union after TMC joint arthrodesis is unknown, but HCS has the best overall biomechanical performance and, therefore, might be considered the best choice for this clinical setting.

The Contribution of the Sheep and the Goat Model to the Study of Ovarian Ageing

Ovarian ageing stands as the major contributor towards fertility loss. As such, there is an urge for studies addressing the mechanisms that promote ovarian ageing and new strategies aiming to delay it. Recently, the presence of a unique population of multinucleated giant cells has been identified in the ovaries of reproductively aged mice. These cells have been considered hallmarks of ovarian ageing. However, up to date multinucleated giant cells have only been described in the ovaries of the mice. Therefore, the aim of the present work was to evaluate and characterize the presence of such hallmarks of ovarian ageing in the sheep and the goat. In this study, ovaries from juvenile (6 months) and mature animals (18-24 months) were used. The hematoxylin and eosin technique was performed to describe the ovarian morphology and evaluate the ovarian follicle reserve pool. Sudan black B staining and the detection of autofluorescence emission were used to identify and characterize the presence of multinucleated giant cells. Statistical analyses were performed with GraphPad Prism 9.0.0. A decrease in the follicle reserve pool and the presence of multinucleated giant cells, with lipofuscin accumulation and the emission of autofluorescence, were observed in the ovaries of the mature animals of both species. Our results support the interest in the use of the ovine and the caprine model, that share physiological and pathophysiological characteristics with humans, in future studies addressing ovarian ageing.

Vancomycin-Loaded, Nanohydroxyapatite-Based Scaffold for Osteomyelitis Treatment: In Vivo Rabbit Toxicological Tests and In Vivo Efficacy Tests in a Sheep Model

The treatment for osteomyelitis consists of surgical debridement, filling of the dead space, soft tissue coverage, and intravenous administration of antimicrobial (AM) agents for long periods. Biomaterials for local delivery of AM agents, while providing controllable antibiotic release rates and simultaneously acting as a bone scaffold, may be a valuable alternative; thus, avoiding systemic AM side effects. V-HEPHAPC is a heparinized nanohydroxyapatite (nHA)/collagen biocomposite loaded with vancomycin that has been previously studied and tested in vitro. It enables a vancomycin-releasing profile with an intense initial burst, followed by a sustained release with concentrations above the Minimum Inhibitory Concentration (MIC) for MRSA. In vitro results have also shown that cellular viability is not compromised, suggesting that V-HEPHAPC granules may be a promising alternative device for the treatment of osteomyelitis. In the present study, V-HEPHAPC (HEPHAPC with vancomycin) granules were used as a vancomycin carrier to treat MRSA osteomyelitis. First, in vivo Good Laboratory Practice (GLP) toxicological tests were performed in a rabbit model, assuring that HEPHAPC and V-HEPHAPC have no relevant side effects. Second, V-HEPHAPC proved to be an efficient drug carrier and bone substitute to control MRSA infection and simultaneously reconstruct the bone cavity in a sheep model.

Novel nano-hydroxyapatite coating of additively manufactured three-dimensional porous implants improves bone ingrowth and initial fixation

Electron beam melting (EBM) has been used to fabricate three-dimensional (3D) porous Ti-6Al-4V surfaces for acetabular cups in total hip arthroplasty. However, there are radiographic concerns regarding poor implant fixation and bone ingrowth around electron beam melted (EBMed) 3D porous cups. We hypothesize that nano-hydroxyapatite (nHA) coating can promote bone ingrowth and thus decrease the occurrence of radiolucent lines around EBMed 3D porous cups. This study aimed to investigate the effect of a novel nHA coating on the biological performance of EBMed 3D porous implants in a beagle transcortical model. Low-porosity (control) and high-porosity 3D porous Ti-6Al-4V implants were manufactured using EBM. Half of the high-porosity implants were coated with nHA without clogging the 3D pores. Implants were inserted into the femoral diaphysis of the beagles. The beagles were euthanized at 4, 8, and 12 weeks postoperatively, and push-out testing was performed. Bone ingrowth was evaluated by histological analysis. Although the increase in porosity alone had no effect on biological behavior, the addition of nHA to high-porosity 3D implants significantly improved early bone fixation and bone ingrowth into the deep region of porous structures compared to low-porosity implants. This is the first report of a novel nHA coating that improved bone ingrowth into the deeper regions of 3D porous implants, which can prevent the occurrence of radiolucent lines around EBMed 3D porous cups.

Long-term in vivo observations show biocompatibility and performance of ZX00 magnesium screws surface-modified by plasma-electrolytic oxidation in Göttingen miniature pigs

Bioabsorbable magnesium implants for orthopedic fixation of bone have recently become available for different fields of indication. While general questions of biocompatibility have been answered, tailoring suitable degradation kinetics for specific applications as well as long-term tissue integration remain the focus of current research. The aim of this study was the evaluation of the long-term degradation behavior and osseointegration of Mg-Ca-Zn (ZX00MEO) based magnesium implants with plasma-electrolytic oxidation (PEO) surface modification (ZX00MEO-PEO) in comparison to non-surface modified implants in vivo and in vitro. Besides a general evaluation of the biological performance of the alloy over a prolonged period, the main hypothesis was that PEO surface modification significantly reduces implant degradation rate and improves tissue interaction. In vitro, the microstructure and surface of the bioabsorbable screws were characterized by SEM/EDS, cytocompatibility and degradation testing facilitating hydrogen gas evolution, carried out following ISO 10993-5/-12 and ASTM F3268-18a/ASTM G1-03 (E1:2017). In vivo, screws were implanted in the frontal bone of Minipigs for 6, 12, and 18 months, following radiological and histomorphometric analysis. A slower and more uniform degradation and improved cytocompatibility could be shown for the ZX00MEO-PEO group in vitro. A significant reduction of degradation rate and enhanced bone formation around the ZX00MEO-PEO screws in vivo was confirmed. Proficient biocompatibility and tissue integration could generally be shown in vivo regardless of surface state. The tested magnesium alloy shows generally beneficial properties as an implant material, while PEO-surface modification further improves the bioabsorption behavior both in vitro and in vivo. STATEMENT OF SIGNIFICANCE: Devices from bioabsorbable Magnesium have recently been introduced to orthopedic applications. However, the vast degradation of Magnesium within the human body still gives limitations. While reliable in-vivo data on most promising surface treatments such as Plasma-electrolytic-Oxidation is generally scarce, long-time results in large animals are to this date completely missing. To overcome this lack of evidence, we studied a Magnesium-Calzium-Zinc-alloy with surface enhancement by PEO for the first time ever over a period of 18 months in a large animal model. In-vitro, surface-modified screws showed significantly improved cytocompatibility and reduction of degradation confirmed by hydrogen gas evolution testing, while in-vivo radiological and histological evaluation generally showed good biocompatibility and bioabsorption as well as significantly enhanced reduction of degradation and faster bone regeneration in the PEO-surface-modified group.

Temporal metabolic profiling of bone healing in a caprine tibia segmental defect model

Bone tissue engineering is an emerging field of regenerative medicine, with a wide array of biomaterial technologies and therapeutics employed. However, it is difficult to objectively compare these various treatments during various stages of tissue response. Metabolomics is rapidly emerging as a powerful analytical tool to establish broad-spectrum metabolic signatures for a target biological system. Developing an effective biomarker panel for bone repair from small molecule data would provide an objective metric to readily assess the efficacy of novel therapeutics in relation to natural healing mechanisms. In this study we utilized a large segmental bone defect in goats to reflect trauma resulting in substantial volumetric bone loss. Characterization of the native repair capacity was then conducted over a period of 12 months through the combination of standard (radiography, computed tomography, histology, biomechanics) data and ultra-high-performance liquid chromatography-high resolution mass spectrometry (UHPLC-HRMS) metabolic profiling. Standard metrics demonstrated that samples formed soft callus structures that later mineralized. Small molecule profiles showed distinct temporal patterns associated with the bone tissue repair process. Specifically, increased lactate and amino acid levels at early time points indicated an environment conducive to osteoblast differentiation and extracellular matrix formation. Citrate and pyruvate abundances increased at later time points indicating increasing mineral content within the defect region. Taurine, shikimate, and pantothenate distribution profiles appeared to represent a shift toward a more homeostatic remodeling environment with the differentiation and activity of osteoclasts offsetting the earlier deposition phases of bone repair. The generation of a comprehensive metabolic reference portfolio offers a potent mechanism for examining novel biomaterials and can serve as guide for the development of new targeted therapeutics to improve the rate, magnitude, and quality of bone regeneration.

Enhanced bone formation in locally-optimised, low-stiffness additive manufactured titanium implants: An in silico and in vivo tibial advancement study

A tibial tuberosity advancement (TTA), used to treat lameness in the canine stifle, provides a framework to investigate implant performance within an uneven loading environment due to the dominating patellar tendon. The purpose of this study was to reassess how we design orthopaedic implants in a load-bearing model to investigate potential for improved osseointegration capacity of fully-scaffolded mechanically-matched additive manufactured (AM) implants. While the mechanobiological nature of bone is well known, we have identified a lower limit in the literature where investigation into exceedingly soft scaffolds relative to trabecular bone ceases due to the trade-off in mechanical strength. We developed a finite element model of the sheep stifle to assess the stresses and strains of homogeneous and locally-optimised TTA implant designs. Using additive manufacturing, we printed three different low-stiffness Ti-6Al-4 V TTA implants: 0.8 GPa (Ti1), 0.6 GPa (Ti2) and an optimised design with a 0.3 GPa cortex and 0.1 GPa centre (Ti3), for implantation in a 12-week in vivo ovine pilot study. Static histomorphometry demonstrated uniform bone ingrowth in optimised low-modulus Ti3 samples compared to homogeneous designs (Ti1 and Ti2), and greater bone-implant contact. Mineralising surfaces were apparent in all implants, though mineral apposition rate was only consistent throughout Ti3. The greatest bone formation scores were seen in Ti3, followed by Ti2 and Ti1. Results from our study suggest lower stiffnesses and higher strain ranges improve early bone formation, and that by accounting for loading environments through rational design, implants can be optimised to improve uniform osseointegration. STATEMENT OF SIGNIFICANCE: The effect of different strain ranges on bone healing has been traditionally investigated and characterised through computational models, with much of the literature suggesting higher strain ranges being favourable. However, little has been done to incorporate strain-optimisation into porous orthopaedic implants due to the trade-off in mechanical strength required to induce these microenvironments. In this study, we used finite element analysis to optimise the design of additive manufactured (AM) titanium orthopaedic implants for different strain ranges, using a clinically-relevant surgical model. Our research suggests that there is potential for locally-optimised AM scaffolds in the use of orthopaedic devices to induce higher strains, which in turn encourages de novo bone formation and uniform osseointegration.

[Models of bone defects in rabbits used to evaluate the bone graft materials efficacy]

The review deals with the main types of experimental models of bone defects of the skull in rabbits. The information about the types of critical defects, methods of their modeling and the possibilities of application of the described models in the studies of bone graft materials in dentistry and maxillofacial surgery is systematized.