The Applications of 3D Printing for Craniofacial Tissue Engineering

Melt electrowriting of bioglass-laden poly(ε-caprolactone) scaffolds for bone regeneration

Novel and promising biomaterials for bone tissue engineering have been investigated over the years. Aiming to contribute to this progress, this study developed and evaluated polycaprolactone (PCL) scaffolds with 5% (w/w) 58S-bioactive glass (58S-BG) fabricated via melt electrowriting (MEW). Morphological and chemical characterization of the scaffolds was conducted. The biological potential was assessed in vitro with alveolar bone-derived mesenchymal stem cells through cytotoxicity, adhesion, protein production, alkaline phosphatase activity, and mineral nodule formation assays. In vivo, scaffolds implanted in rats were analyzed for biocompatibility, inflammation, and degradation using H&E staining and immunohistochemical markers for angiogenesis and macrophage polarization. Statistical analysis was performed at a 5% significance level. Appropriate fiber alignment but a higher fiber diameter was found for PCL + BG5% compared to PCL scaffolds (p = 0.002). EDS spectra confirmed the presence of BG's chemical components for BG-laden scaffolds, attesting to BG particle incorporation into the filaments. Raman spectroscopy evidenced the chemical nature of the BG powder, and FTIR spectra revealed -OH stretching for PCL + BG5%, evidencing its hydrophilic potential. None of the scaffolds were cytotoxic, and BG-laden formulation increased cell viability after 7 days (p = 0.0006), also showing greater cell adhesion/spreading over time compared to pristine PCL scaffolds. BG's presence also increased the mineral matrix formation (p ≤ 0.0021) over 21 days and retained ALP activity after 14 days (p = 0.705) compared to PCL. In vivo, PCL scaffolds retained fiber alignment and preserved their volume throughout the evaluation, showing minimal structural alteration. In contrast, PCL + BG5% scaffolds showed more visible structural changes at 28 days. Despite this, the PCL + BG5% formulation remained biocompatible and significantly promoted angiogenesis compared to pristine PCL scaffolds. In sum, BG-laden scaffolds were successfully melt electrowritten, retaining the scaffolds' porous architecture, showing appropriate properties, including cell viability, adhesion, mineralized nodule deposition, biocompatibility, and angiogenesis, indicating that these materials are a promising alternative for enhancing bone tissue regeneration.

Personalized bioceramic grafts for craniomaxillofacial bone regeneration

The reconstruction of craniomaxillofacial bone defects remains clinically challenging. To date, autogenous grafts are considered the gold standard but present critical drawbacks. These shortcomings have driven recent research on craniomaxillofacial bone reconstruction to focus on synthetic grafts with distinct materials and fabrication techniques. Among the various fabrication methods, additive manufacturing (AM) has shown significant clinical potential. AM technologies build three-dimensional (3D) objects with personalized geometry customizable from a computer-aided design. These layer-by-layer 3D biomaterial structures can support bone formation by guiding cell migration/proliferation, osteogenesis, and angiogenesis. Additionally, these structures can be engineered to degrade concomitantly with the new bone tissue formation, making them ideal as synthetic grafts. This review delves into the key advances of bioceramic grafts/scaffolds obtained by 3D printing for personalized craniomaxillofacial bone reconstruction. In this regard, clinically relevant topics such as ceramic-based biomaterials, graft/scaffold characteristics (macro/micro-features), material extrusion-based 3D printing, and the step-by-step workflow to engineer personalized bioceramic grafts are discussed. Importantly, in vitro models are highlighted in conjunction with a thorough examination of the signaling pathways reported when investigating these bioceramics and their effect on cellular response/behavior. Lastly, we summarize the clinical potential and translation opportunities of personalized bioceramics for craniomaxillofacial bone regeneration.

3D Melt-Extrusion Printing of Medium Chain Length Polyhydroxyalkanoates and Their Application as Antibiotic-Free Antibacterial Scaffolds for Bone Regeneration

In this work, we investigated, for the first time, the possibility of developing scaffolds for bone tissue engineering through three-dimensional (3D) melt-extrusion printing of medium chain length polyhydroxyalkanoate (mcl-PHA) (i.e., poly(3-hydroxyoctanoate-co-hydroxydecanoate-co-hydroxydodecanoate), P(3HO-co-3HD-co-3HDD)). The process parameters were successfully optimized to produce well-defined and reproducible 3D P(3HO-co-3HD-co-3HDD) scaffolds, showing high cell viability (100%) toward both undifferentiated and differentiated MC3T3-E1 cells. To introduce antibacterial features in the developed scaffolds, two strategies were investigated. For the first strategy, P(3HO-co-3HD-co-3HDD) was combined with PHAs containing thioester groups in their side chains (i.e., PHACOS), inherently antibacterial PHAs. The 3D blend scaffolds were able to induce a 70% reduction of Staphylococcus aureus 6538P cells by direct contact testing, confirming their antibacterial properties. Additionally, the scaffolds were able to support the growth of MC3T3-E1 cells, showing the potential for bone regeneration. For the second strategy, composite materials were produced by the combination of P(3HO-co-3HD-co-HDD) with a novel antibacterial hydroxyapatite doped with selenium and strontium ions (Se-Sr-HA). The composite material with 10 wt % Se-Sr-HA as a filler showed high antibacterial activity against both Gram-positive (S. aureus 6538P) and Gram-negative bacteria (Escherichia coli 8739), through a dual mechanism: by direct contact (inducing 80% reduction of both bacterial strains) and through the release of active ions (leading to a 54% bacterial cell count reduction for S. aureus 6538P and 30% for E. coli 8739 after 24 h). Moreover, the composite scaffolds showed high viability of MC3T3-E1 cells through both indirect and direct testing, showing promising results for their application in bone tissue engineering.

Exosome-loaded hydrogels for craniofacial bone tissue regeneration

It is common for maladies and trauma to cause significant bone deterioration in the craniofacial bone, which can cause patients to experience complications with their appearance and their ability to function. Regarding grafting procedures' complications and disadvantages, the newly emerging field of tissue regeneration has shown promise. Tissue -engineered technologies and their applications in the craniofacial region are increasingly gaining prominence with limited postoperative risk and cost. MSCs-derived exosomes are widely applied in bone tissue engineering to provide cell-free therapies since they not only do not cause immunological rejection in the same way that cells do, but they can also perform a cell-like role. Additionally, the hydrogel system is a family of multipurpose platforms made of cross-linked polymers with considerable water content, outstanding biocompatibility, and tunable physiochemical properties for the efficient delivery of commodities. Therefore, the promising exosome-loaded hydrogels can be designed for craniofacial bone regeneration. This review lists the packaging techniques for exosomes and hydrogel and discusses the development of a biocompatible hydrogel system and its potential for exosome continuous delivery for craniofacial bone healing.

Single/Multi-Network Conductive Hydrogels-A Review

Hydrogels made from conductive organic materials have gained significant interest in recent years due to their wide range of uses, such as electrical conductors, freezing resistors, biosensors, actuators, biomedical engineering materials, drug carrier, artificial organs, flexible electronics, battery solar cells, soft robotics, and self-healers. Nevertheless, the insufficient level of effectiveness in electroconductive hydrogels serves as a driving force for researchers to intensify their endeavors in this domain. This article provides a concise overview of the recent advancements in creating self-healing single- or multi-network (double or triple) conductive hydrogels (CHs) using a range of natural and synthetic polymers and monomers. We deliberated on the efficacy, benefits, and drawbacks of several conductive hydrogels. This paper emphasizes the use of natural polymers and innovative 3D printing CHs-based technology to create self-healing conductive gels for flexible electronics. In conclusion, advantages and disadvantages have been noted, and some potential opportunities for self-healing single- or multi-network hydrogels have been proposed.

Advances in biomaterials for oral-maxillofacial bone regeneration: spotlight on periodontal and alveolar bone strategies

The intricate nature of oral-maxillofacial structure and function, coupled with the dynamic oral bacterial environment, presents formidable obstacles in addressing the repair and regeneration of oral-maxillofacial bone defects. Numerous characteristics should be noticed in oral-maxillofacial bone repair, such as irregular morphology of bone defects, homeostasis between hosts and microorganisms in the oral cavity and complex periodontal structures that facilitate epithelial ingrowth. Therefore, oral-maxillofacial bone repair necessitates restoration materials that adhere to stringent and specific demands. This review starts with exploring these particular requirements by introducing the particular characteristics of oral-maxillofacial bones and then summarizes the classifications of current bone repair materials in respect of composition and structure. Additionally, we discuss the modifications in current bone repair materials including improving mechanical properties, optimizing surface topography and pore structure and adding bioactive components such as elements, compounds, cells and their derivatives. Ultimately, we organize a range of potential optimization strategies and future perspectives for enhancing oral-maxillofacial bone repair materials, including physical environment manipulation, oral microbial homeostasis modulation, osteo-immune regulation, smart stimuli-responsive strategies and multifaceted approach for poly-pathic treatment, in the hope of providing some insights for researchers in this field. In summary, this review analyzes the complex demands of oral-maxillofacial bone repair, especially for periodontal and alveolar bone, concludes multifaceted strategies for corresponding biomaterials and aims to inspire future research in the pursuit of more effective treatment outcomes.

Unlocking the Future: Bioprinting Salivary Glands-From Possibility to Reality

Salivary gland biofabrication represents a promising avenue in regenerative medicine, aiming to address the challenges of salivary gland dysfunction caused by various factors such as autoimmune diseases and radiotherapy. This review examines the current state of bioprinting technology, biomaterials, and tissue engineering strategies in the context of creating functional, implantable salivary gland constructs. Key considerations include achieving vascularization for proper nutrient supply, maintaining cell viability and functionality during printing, and promoting tissue maturation and integration with surrounding tissues. Despite the existing challenges, recent advancements offer significant potential for the development of personalized therapeutic options to treat salivary gland disorders. Continued research and innovation in this field hold the potential to revolutionize the management of salivary gland conditions, improving patient outcomes and quality of life. This systematic review covers publications from 2018 to April 2024 and was conducted on four databases: Google Scholar, PubMed, EBSCOhost, and Web of Science. The key features necessary for the successful creation, implantation and functioning of bioprinted salivary glands are addressed.

Direct inkjet writing type 1 bovine collagen/β-tricalcium phosphate scaffolds for bone regeneration

Bone tissue has the capacity to regenerate under healthy conditions, but complex cases like critically sized defects hinder natural bone regeneration, necessitating surgery, and use of a grafting material for rehabilitation. The field of bone tissue engineering (BTE) has pioneered ways to address such issues utilizing different biomaterials to create a platform for cell migration and tissue formation, leading to improved bone reconstruction. One such approach involves 3D-printed patient-specific scaffolds designed to aid in regeneration of boney defects. This study aimed to develop and characterize 3D printed scaffolds composed of type I collagen augmented with β-tricalcium phosphate (COL/β-TCP). A custom-built direct inkjet write (DIW) printer was used to fabricate β-TCP, COL, and COL/β-TCP scaffolds using synthesized colloidal gels. After chemical crosslinking, the scaffolds were lyophilized and subjected to several characterization techniques, including light microscopy, scanning electron microscopy, and x-ray diffraction to evaluate morphological and chemical properties. In vitro evaluation was performed using human osteoprogenitor cells to assess cytotoxicity and proliferative capacity of the different scaffold types. Characterization results confirmed the presence of β-TCP in the 3D printed COL/β-TCP scaffolds, which exhibited crystals that were attributed to β-TCP due to the presence of calcium and phosphorus, detected through energy dispersive x-ray spectroscopy. In vitro studies showed that the COL/β-TCP scaffolds yielded more favorable results in terms of cell viability and proliferation compared to β-TCP and COL scaffolds. The novel COL/β-TCP scaffold constructs hold promise for improving BTE applications and may offer a superior environment for bone regeneration compared with conventional COL and β-TCP scaffolds.

Design, Preparation, and Mechanical Property Study of Polylactic Acid/Ca2BO3Cl: Eu2+, Dy3+ Composite Material for 3D Printing

To break through the simplification of three-dimensional printing (3DP) materials and realize the application of long-persistent phosphors in more fields, polylactic acid doped with Ca2BO3Cl: Eu2+, Dy3+ was prepared in this study. The structure of the mixtures was analyzed and determined by infrared spectroscopy. The luminescence properties of phosphors and the composites were studied by fluorescence spectra and afterglow decay curve measurements. The yellow light of the mixtures could be attributed to the 5d-4f energy level transition of Eu2+. After the excitation of 254 nm ultraviolet lamp, the luminance and duration of the composites could be clearly observed. The mechanical properties of the composite filaments were tested, including maximal force and elasticity modulus. In particular, the influence of humidity on mechanical properties was analyzed in detail. The prepared composite filaments were printed into hollow dodecahedrons and presented in this study. Therefore, the composites had great properties and might be expected to put into practical applications of 3DP technology.

Three-Dimensional Printed Poly (Lactic-co-Glycolic Acid)-Magnesium Composite Scaffolds for the Promotion of Osteogenesis Through Immunoregulation

Scaffolds play an important role in bone tissue engineering. The ideal engineered scaffold needs to be biocompatible, bioactive, and able to regulate immune cells to enhance bone regeneration. In this study, magnesium (Mg)-contained poly(lactic-co-glycolic acid) (PLGA) scaffolds (hereinafter, referred to as PLGA-2Mg) were fabricated by 3-dimensional printing using a mixture of PLGA and MgSO 4 powder. Poly(lactic-co-glycolic acid) scaffolds (hereinafter, referred to as PLGA) were also fabricated by 3-dimensional printing and were used as control. The biocompatibility, immunoregulatory ability, and osteogenic properties of PLGA-2Mg were analyzed and compared with those of PLGA. The results indicate that the incorporation of Mg increased the Young modulus and surface roughness of the scaffold, but did not affect its degradation. The PLGA-2Mg further promoted the adhesion and proliferation of MC3T3-E1 cells compared with PLGA, which indicates its improved biocompatibility and bioactivity. In addition, PLGA-2Mg inhibited the polarization of RAW 264.7 cells toward the M1 phenotype by down-regulating the IL-1β , IL-6 , and iNOs gene expression when challenged with lipopolysaccharide stimulation. In contrast, it promoted the polarization of RAW 264.7 cells toward the M2 phenotype by up-regulating the TGF-β , IL-10 , and Arg-1 gene expression without lipopolysaccharide stimulation. Finally, MC3T3-E1 cells were cocultured with RAW 264.7 cells and scaffolds using a transwell system. It was found that the expression level of osteogenic-related genes ( ALP , COL-1 , BMP2 , and BSP ) was significantly upregulated in the PLGA-2Mg group compared with that in the PLGA group. Consequently, PLGA-2Mg with increased biocompatibility and bioactivity can promote osteogenesis through immunoregulation and has the potential to be used as a novel scaffold in bone tissue engineering.

Advancing Dentistry through Bioprinting: Personalization of Oral Tissues

Despite significant advancements in dental tissue restoration and the use of prostheses for addressing tooth loss, the prevailing clinical approaches remain somewhat inadequate for replicating native dental tissue characteristics. The emergence of three-dimensional (3D) bioprinting offers a promising innovation within the fields of regenerative medicine and tissue engineering. This technology offers notable precision and efficiency, thereby introducing a fresh avenue for tissue regeneration. Unlike the traditional framework encompassing scaffolds, cells, and signaling factors, 3D bioprinting constitutes a contemporary addition to the arsenal of tissue engineering tools. The ongoing shift from conventional dentistry to a more personalized paradigm, principally under the guidance of bioprinting, is poised to exert a significant influence in the foreseeable future. This systematic review undertakes the task of aggregating and analyzing insights related to the application of bioprinting in the context of regenerative dentistry. Adhering to PRISMA guidelines, an exhaustive literature survey spanning the years 2019 to 2023 was performed across prominent databases including PubMed, Scopus, Google Scholar, and ScienceDirect. The landscape of regenerative dentistry has ushered in novel prospects for dentoalveolar treatments and personalized interventions. This review expounds on contemporary accomplishments and avenues for the regeneration of pulp-dentin, bone, periodontal tissues, and gingival tissues. The progressive strides achieved in the realm of bioprinting hold the potential to not only enhance the quality of life but also to catalyze transformative shifts within the domains of medical and dental practices.

Recent advances and future directions of 3D to 6D printing in brain cancer treatment and neural tissue engineering

The field of neural tissue engineering has undergone a revolution due to advancements in three-dimensional (3D) printing technology. This technology now enables the creation of intricate neural tissue constructs with precise geometries, topologies, and mechanical properties. Currently, there are various 3D printing techniques available, such as stereolithography and digital light processing, and a wide range of materials can be utilized, including hydrogels, biopolymers, and synthetic materials. Furthermore, the development of four-dimensional (4D) printing has gained traction, allowing for the fabrication of structures that can change shape over time using techniques such as shape-memory polymers. These innovations have the potential to facilitate neural regeneration, drug screening, disease modeling, and hold tremendous promise for personalized diagnostics, precise therapeutic strategies against brain cancers. This review paper provides a comprehensive overview of the current state-of-the-art techniques and materials for 3D printing in neural tissue engineering and brain cancer. It focuses on the exciting possibilities that lie ahead, including the emerging field of 4D printing. Additionally, the paper discusses the potential applications of five-dimensional and six-dimensional printing, which integrate time and biological functions into the printing process, in the fields of neuroscience.

Classification, processing, and applications of bioink and 3D bioprinting: A detailed review

With the advancement in 3D bioprinting technology, cell culture methods can design 3D environments which are both, complex and physiologically relevant. The main component in 3D bioprinting, bioink, can be split into various categories depending on the criterion of categorization. Although the choice of bioink and bioprinting process will vary greatly depending on the application, general features such as material properties, biological interaction, gelation, and viscosity are always important to consider. The foundation of 3D bioprinting is the exact layer-by-layer implantation of biological elements, biochemicals, and living cells with the spatial control of the implantation of functional elements onto the biofabricated 3D structure. Three basic strategies underlie the 3D bioprinting process: autonomous self-assembly, micro tissue building blocks, and biomimicry or biomimetics. Tissue engineering can benefit from 3D bioprinting in many ways, but there are still numerous obstacles to overcome before functional tissues can be produced and used in clinical settings. A better comprehension of the physiological characteristics of bioink materials and a higher level of ability to reproduce the intricate biologically mimicked and physiologically relevant 3D structures would be a significant improvement for 3D bioprinting to overcome the limitations.

Emerging Technologies of Three-Dimensional Printing and Mobile Health in COVID-19 Immunity and Regenerative Dentistry

The ongoing coronavirus disease 2019 (COVID-19) pandemic highlights the importance of developing point-of-care (POC) antibody tests for monitoring the COVID-19 immune response upon viral infection or following vaccination, which requires three key aspects to achieve optimal monitoring, including three-dimensional (3D)-printed POC devices, mobile health (mHealth), and noninvasive sampling. As a critical tissue engineering concept, additive manufacturing (AM, also known as 3D printing) enables accurate control over the dimensional and architectural features of the devices. mHealth refers to the use of portable digital devices, such as smartphones, tablet computers, and fitness and medical wearables, to support health, which facilitates contact tracing, and telehealth consultations during the pandemic. Compared with invasive biosample (blood), saliva is of great importance in the spread and surveillance of COVID-19 as a noninvasive diagnostic method for virus detection and immune status monitoring. However, investigations into 3D-printed POC antibody test and mHealth using noninvasive saliva are relatively limited. Further exploration of 3D-printed antibody POC tests and mHealth applications to monitor antibody production for either disease onset or immune response following vaccination is warranted. This review briefly describes the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus and immune response after infection and vaccination, then discusses current widely used binding antibody tests using blood samples and enzyme-linked immunosorbent assays on two-dimensional microplates before focusing upon emerging POC technological platforms, such as field-effect transistor biosensors, lateral flow assay, microfluidics, and AM for fabricating immunoassays, and the possibility of their combination with mHealth. This review proposes that noninvasive biofluid sampling combined with 3D POC antibody tests and mHealth technologies is a promising and novel approach for POC detection and surveillance of SARS-CoV-2 immune response. Furthermore, as key concepts in dentistry, the application of 3D printing and mHealth was also included to facilitate the appreciation of cutting edge techniques in regenerative dentistry. This review highlights the potential of 3D printing and mHealth in both COVID-19 immunity monitoring and regenerative dentistry.

Hydrogels-A Promising Materials for 3D Printing Technology

Hydrogels are a promising material for a variety of applications after appropriate functional and structural design, which alters the physicochemical properties and cell signaling pathways of the hydrogels. Over the past few decades, considerable scientific research has made breakthroughs in a variety of applications such as pharmaceuticals, biotechnology, agriculture, biosensors, bioseparation, defense, and cosmetics. In the present review, different classifications of hydrogels and their limitations have been discussed. In addition, techniques involved in improving the physical, mechanical, and biological properties of hydrogels by admixing various organic and inorganic materials are explored. Future 3D printing technology will substantially advance the ability to pattern molecules, cells, and organs. With significant potential for producing living tissue structures or organs, hydrogels can successfully print mammalian cells and retain their functionalities. Furthermore, recent advances in functional hydrogels such as photo- and pH-responsive hydrogels and drug-delivery hydrogels are discussed in detail for biomedical applications.

Microfabrication approaches for oral research and clinical dentistry

Currently, a variety of laboratory tools and strategies have been developed to investigate in vivo processes using in vitro models. Amongst these, microfabrication represents a disruptive technology that is currently enabling next-generation biomedical research through the development of complex laboratory approaches (e.g., microfluidics), engineering of micrometer scale sensors and actuators (micropillars for traction force microscopy), and the creation of environments mimicking cell, tissue, and organ-specific contexts. Although microfabrication has been around for some time, its application in dental and oral research is still incipient. Nevertheless, in recent years multiple lines of research have emerged that use microfabrication-based approaches for the study of oral diseases and conditions with micro- and nano-scale sensitivities. Furthermore, many investigations are aiming to develop clinically relevant microfabrication-based applications for diagnostics, screening, and oral biomaterial manufacturing. Therefore, the objective of this review is to summarize the current application of microfabrication techniques in oral sciences, both in research and clinics, and to discuss possible future applications of these technologies for in vitro studies and practical patient care. Initially, this review provides an overview of the most employed microfabrication methods utilized in biomedicine and dentistry. Subsequently, the use of micro- and nano-fabrication approaches in relevant fields of dental research such as endodontic and periodontal regeneration, biomaterials research, dental implantology, oral pathology, and biofilms was discussed. Finally, the current and future uses of microfabrication technology for clinical dentistry and how these approaches may soon be widely available in clinics for the diagnosis, prevention, and treatment of relevant pathologies are presented.

Advanced Hydrogel systems for mandibular reconstruction

Mandibular defect becomes a prevalent maxillofacial disease resulting in mandibular dysfunctions and huge psychological burdens to the patients. Considering the routine presence of oral contaminations and aesthetic restoration of facial structures, the current clinical treatments are however limited, incapable to reconstruct the structural integrity and regeneration, spurring the need for cost-effective mandibular tissue engineering. Hydrogel systems possess great merit for mandibular reconstruction with precise involvement of cells and bioactive factors. In this review, current clinical treatments and distinct mode(s) of mandible formation and pathological resorption are summarized, followed by a review of hydrogel-related mandibular tissue engineering, and an update on the advanced fabrication of hydrogels with improved mechanical property, antibacterial ability, injectable form, and 3D bioprinted hydrogel constructs. The exploration of advanced hydrogel systems will lay down a solid foundation for a bright future with more biocompatible, effective, and personalized treatment in mandibular reconstruction.

Recent progress and clinical applications of advanced biomaterials in cosmetic surgery

Materials of different allogeneic or xenogeneic or autologous origins are widely used as soft-tissue fillers or structural scaffolds in the field of cosmetic surgery, while complications including prosthesis infection, donor site deformity and filler embolization have always been difficult problems for plastic surgeons. The application of novel biomaterials may bring in hopeful solutions for these problems. Recently, some advanced biomaterials, such as regenerative biomaterials can effectively promote the repair of defective tissues, which have been proven to have good therapeutic as well as cosmetic effects in cosmetic surgery. Therefore, biomaterials with active compounds have drawn significant attention for the tissue regeneration of reconstructive and esthetic treatment. Some of these applications have achieved better clinical outcomes than traditional biological materials. This review summarized recent progress and clinical applications of advanced biomaterials in cosmetic surgery.

3D-printed mesoporous bioactive glass/GelMA biomimetic scaffolds for osteogenic/cementogenic differentiation of periodontal ligament cells

Integrated regeneration of periodontal tissues remains a challenge in current clinical applications. Due to the tunable physical characteristics and the precise control of the scaffold microarchitecture, three-dimensionally (3D) printed gelatin methacryloyl (GelMA)-based scaffold has emerged as a promising strategy for periodontal tissue regeneration. However, the optimization of the printing biomaterial links the formulation and the relationship between the composition and structures of the printed scaffolds and their comprehensive properties (e.g. mechanical strength, degradation, and biological behaviors) remains unclear. Here, in this work, a novel mesoporous bioactive glass (BG)/GelMA biomimetic scaffold with a large pore size (∼300 μm) was developed by extrusion-based 3D printing. Our results showed that the incorporation of mesoporous bioactive glass nanoparticles (BG NPs) significantly improved shape fidelity, surface roughness, and bioactivity of 3D-printed macroporous GelMA scaffolds, resulting in the enhanced effects on cell attachment and promoting osteogenic/cementogenic differentiation in human periodontal ligament cells. The excellent maintenance of the macropore structure, the visibly improved cells spreading, the release of bioactive ions (Si4+, Ca2+), the upregulation of gene expressions of osteogenesis and cementogensis, and the increase in alkaline phosphatase (ALP) activity and calcium nodules suggested that BG NPs could endow GelMA-based scaffolds with excellent structural stability and the ability to promote osteogenic/cementogenic differentiation. Our findings demonstrated the great potential of the newly formulated biomaterial inks and biomimetic BG/GelMA scaffolds for being used in periodontal tissue regeneration and provide important insights into the understanding of cell-scaffold interaction in promoting the regeneration of functional periodontal tissues.

Anatomical Engineering and 3D Printing for Surgery and Medical Devices: International Review and Future Exponential Innovations

Three-dimensional printing (3DP) has recently gained importance in the medical industry, especially in surgical specialties. It uses different techniques and materials based on patients' needs, which allows bioprofessionals to design and develop unique pieces using medical imaging provided by computed tomography (CT) and magnetic resonance imaging (MRI). Therefore, the Department of Biology and Medicine and the Department of Physics and Engineering, at the Bioastronautics and Space Mechatronics Research Group, have managed and supervised an international cooperation study, in order to present a general review of the innovative surgical applications, focused on anatomical systems, such as the nervous and craniofacial system, cardiovascular system, digestive system, genitourinary system, and musculoskeletal system. Finally, the integration with augmented, mixed, virtual reality is analyzed to show the advantages of personalized treatments, taking into account the improvements for preoperative, intraoperative planning, and medical training. Also, this article explores the creation of devices and tools for space surgery to get better outcomes under changing gravity conditions.

Mechanical Property Evaluation of PLA/Soybean Oil Epoxidized Acrylate Three-Dimensional Scaffold in Bone Tissue Engineering

Recently investigated photocurable, biocompatible plant resin on tissue engineering to provide the scaffold with structural support and mechanical properties. A novel method had been used here to build our scaffold by combined the traditional three-dimensional fused deposition modeling (FDM) printing and injected the structural scaffold after fabrication with plant-based resin. The materials used are polymers a synthesized one polylactic acid and soybean oil epoxidized acrylate. The addition of soybean plant-based resin improves the adhesion and proliferation of the PLA scaffold while also providing structural support to the fabricated scaffold. The purpose of the study made optimization of printing parameters and compared different printing scaffolds to select the perfect one with preferred mechanical properties. Two designs are built (cubic design and cylinder design) to make a comparison of mechanical properties between the two designs. The novel method was used through injected soybean oil resin into the PLA scaffold by avoiding any heat and temperature rise of the resin. In the traditional method, the resin is printed using an SLA printer which exposed the resin to heating before printing, this will affect the properties of the final model in our technique temperature will eliminate by direct inject the plant-based resin into the PLA scaffold and then photocuring with ultraviolet curing device for 30 min at 405nm. Finally, the results demonstrate that after injecting PLA scaffold with soybean oil resin, the mechanical properties of the scaffold improve; additionally, the results show that the cylindrical design has more promising mechanical properties than the cubic design.

Bringing hydrogel-based craniofacial therapies to the clinic

This review explores the evolution of the use of hydrogels for craniofacial soft tissue engineering, ranging in complexity from acellular injectable fillers to fabricated, cell-laden constructs with complex compositions and architectures. Addressing both in situ and ex vivo approaches, tissue restoration secondary to trauma or tumor resection is discussed. Beginning with relatively simple epithelia of oral mucosa and gingiva, then moving to more functional units like vocal cords or soft tissues with multilayer branched structures, such as salivary glands, various approaches are presented toward the design of function-driven architectures, inspired by native tissue organization. Multiple tissue replacement paradigms are presented here, including the application of hydrogels as structural materials and as delivery platforms for cells and/or therapeutics. A practical hierarchy is proposed for hydrogel systems in craniofacial applications, based on their material and cellular complexity, spatial order, and biological cargo(s). This hierarchy reflects the regulatory complexity dictated by the Food and Drug Administration (FDA) in the United States prior to commercialization of these systems for use in humans. The wide array of available biofabrication methods, ranging from simple syringe extrusion of a biomaterial to light-based spatial patterning for complex architectures, is considered within the history of FDA-approved commercial therapies. Lastly, the review assesses the impact of these regulatory pathways on the translational potential of promising pre-clinical technologies for craniofacial applications. STATEMENT OF SIGNIFICANCE: While many commercially available hydrogel-based products are in use for the craniofacial region, most are simple formulations that either are applied topically or injected into tissue for aesthetic purposes. The academic literature previews many exciting applications that harness the versatility of hydrogels for craniofacial soft tissue engineering. One of the most exciting developments in the field is the emergence of advanced biofabrication methods to design complex hydrogel systems that can promote the functional or structural repair of tissues. To date, no clinically available hydrogel-based therapy takes full advantage of current pre-clinical advances. This review surveys the increasing complexity of the current landscape of available clinical therapies and presents a framework for future expanded use of hydrogels with an eye toward translatability and U.S. regulatory approval for craniofacial applications.

Bioprinting of Complex Multicellular Organs with Advanced Functionality-Recent Progress and Challenges Ahead

Bioprinting has emerged as one of the most promising strategies for fabrication of functional organs in the lab as an alternative to transplant organs. While progress in the field has mostly been restricted to a few miniaturized tissues with minimal biological functionality until a few years ago, recent progress has advanced the concept of building three-dimensional multicellular organ complexity remarkably. This review discusses a series of milestones that have paved the way for bioprinting of tissue constructs that have advanced levels of biological and architectural functionality. Critical materials, engineering and biological challenges that are key to addressing the desirable function of engineered organs are presented. These are discussed in light of the many difficulties to replicate the heterotypic organization of multicellular solid organs, the nanoscale precision of the extracellular microenvironment in hierarchical tissues, as well as the advantages and limitations of existing bioprinting methods to adequately overcome these barriers. In summary, the advances of the field toward realistic manufacturing of functional organs have never been so extensive, and this manuscript serves as a road map for some of the recent progress and the challenges ahead.

3D magnetic nanocomposite scaffolds enhanced the osteogenic capacities of rat bone mesenchymal stem cells in vitro and in a rat calvarial bone defect model by promoting cell adhesion

Magnetic scaffolds incorporated with iron oxide nanoparticles (IONPs) are biocompatible and present excellent osteogenic properties. However, the underlying mechanism is unclear. In this study, 3D-printed poly(lactic-co-glycolic acid) scaffolds were coated with IONPs using layer-by-layer assembly (Fe-scaffold) to prepare magnetic scaffolds. The effects of this modification on osteogenesis were investigated by comparison with untreated scaffolds (Uncoated-scaffold). The results showed that the proliferation of rat bone mesenchymal stem cells (rBMSCs) on the Fe-scaffold was enhanced compared with those on the Uncoated-scaffold (p < 0.05). The alkaline phosphatase activity and expression levels of osteogenic-related genes of cells on the Fe-scaffold were higher than those on the Uncoated-scaffold (p < 0.05). Fe-scaffold was found to promote the cell adhesion compared with Uncoated-scaffold, including increasing the adhered cell number, promoting cell spreading and upregulating the expression levels of adhesion-related genes integrin α1 and β1 and their downstream signaling molecules FAK and ERK1/2 (p < 0.05). Moreover, the amount of new bone formed in rat calvarial defects at 8 weeks decreased in the order: Fe-scaffold > Uncoated-scaffold > Blank-control (samples whose defects were left empty) (p < 0.05). Therefore, 3D magnetic nanocomposite scaffolds enhanced the osteogenic capacities of rBMSCs in vitro and in a rat calvarial bone defect model by promoting cell adhesion. The mechanisms were attributed to the alteration in its hydrophilicity, surface roughness, and chemical composition.

Regenerative Medicine Technologies to Treat Dental, Oral, and Craniofacial Defects

Additive manufacturing (AM) is the automated production of three-dimensional (3D) structures through successive layer-by-layer deposition of materials directed by computer-aided-design (CAD) software. While current clinical procedures that aim to reconstruct hard and soft tissue defects resulting from periodontal disease, congenital or acquired pathology, and maxillofacial trauma often utilize mass-produced biomaterials created for a variety of surgical indications, AM represents a paradigm shift in manufacturing at the individual patient level. Computer-aided systems employ algorithms to design customized, image-based scaffolds with high external shape complexity and spatial patterning of internal architecture guided by topology optimization. 3D bioprinting and surface modification techniques further enhance scaffold functionalization and osteogenic potential through the incorporation of viable cells, bioactive molecules, biomimetic materials and vectors for transgene expression within the layered architecture. These computational design features enable fabrication of tissue engineering constructs with highly tailored mechanical, structural, and biochemical properties for bone. This review examines key properties of scaffold design, bioresorbable bone scaffolds produced by AM processes, and clinical applications of these regenerative technologies. AM is transforming the field of personalized dental medicine and has great potential to improve regenerative outcomes in patient care.

3D Printing: Advancement in Biogenerative Engineering to Combat Shortage of Organs and Bioapplicable Materials

ABSTRACT

Organ or cell transplantation is medically evaluated for end-stage failure saving or extending the lives of thousands of patients who are suffering from organ failure disorders. The unavailability of adequate organs for transplantation to meet the existing demand is a major challenge in the medical field. This led to day-day-increase in the number of patients on transplant waiting lists as well as in the number of patients dying while on the queue. Recently, technological advancements in the field of biogenerative engineering have the potential to regenerate tissues and, in some cases, create new tissues and organs. In this context, major advances and innovations are being made in the fields of tissue engineering and regenerative medicine which have a huge impact on the scientific community is three-dimensional bioprinting (3D bioprinting) of tissues and organs. Besides this, the decellularization of organs and using this as a scaffold for generating new organs through the recellularization process shows promising results. This review discussed about current approaches for tissue and organ engineering including methods of scaffold designing, recent advances in 3D bioprinting, organs regenerated successfully using 3D printing, and extended application of 3D bioprinting technique in the field of medicine. Besides this, information about commercially available 3D printers has also been included in this article.

LAY SUMMARY

Today's need for organs for the transplantation process in order to save a patient's life or to enhance the survival rate of diseased one is the prime concern among the scientific community. Recent, advances in the field of biogenerative engineering have the potential to regenerate tissues and create organs compatible with the patient's body. In this context, major advances and innovations are being made in the fields of tissue engineering and regenerative medicine which have a huge impact on the scientific community is three-dimensional bioprinting (3D bioprinting) of tissues and organs. Besides this, the decellularization of organs and using this as a scaffold for generating new organs through the recellularization process shows promising results. This review dealt with the current approaches for tissue and organ engineering including methods of scaffold designing, recent advances in 3D bioprinting, organs regenerated successfully using 3D printing, and extended application of 3D bioprinting technique in the field of medicine. Furthermore, information about commercially available 3D printers has also been included in this article.

3D Printing of Micro- and Nanoscale Bone Substitutes: A Review on Technical and Translational Perspectives

Recent developments in three-dimensional (3D) printing technology offer immense potential in fabricating scaffolds and implants for various biomedical applications, especially for bone repair and regeneration. As the availability of autologous bone sources and commercial products is limited and surgical methods do not help in complete regeneration, it is necessary to develop alternative approaches for repairing large segmental bone defects. The 3D printing technology can effectively integrate different types of living cells within a 3D construct made up of conventional micro- or nanoscale biomaterials to create an artificial bone graft capable of regenerating the damaged tissues. This article reviews the developments and applications of 3D printing in bone tissue engineering and highlights the numerous conventional biomaterials and nanomaterials that have been used in the production of 3D-printed scaffolds. A comprehensive overview of the 3D printing methods such as stereolithography (SLA), selective laser sintering (SLS), fused deposition modeling (FDM), and ink-jet 3D printing, and their technical and clinical applications in bone repair and regeneration has been provided. The review is expected to be useful for readers to gain an insight into the state-of-the-art of 3D printing of bone substitutes and their translational perspectives.

Fibrin Glue Implants Seeded with Dental Pulp and Periodontal Ligament Stem Cells for the Repair of Periodontal Bone Defects: A Preclinical Study

A technology to create a cell-seeded fibrin-based implant matching the size and shape of bone defect is required to create an anatomical implant. The aim of the study was to develop a technology of cell-seeded fibrin gel implant creation that has the same shape and size as the bone defect at the site of implantation. Using computed tomography (CT) images, molds representing bone defects were created by 3D printing. The form was filled with fibrin glue and human dental pulp stem cells (DPSC). The viability, set of surface markers and osteogenic differentiation of DPSC grown in fibrin gel along with the clot retraction time were evaluated. In mice, an alveolar bone defect was created. The defect was filled with fibrin gel seeded with mouse DPSC. After 28 days, the bone repair was analyzed with cone beam CT and by histological examination. The proliferation rate, set of surface antigens and osteogenic potential of cells grown inside the scaffold and in 2D conditions did not differ. In mice, both cell-free and mouse DPSC-seeded implants increased the bone tissue volume and vascularization. In mice with cell-seeded gel implants, the bone remodeling process was more prominent than in animals with a cell-free implant. The technology of 3D-printed forms for molding implants can be used to prepare implants using components that are not suitable for 3D printing.

Applications of 3D printed bone tissue engineering scaffolds in the stem cell field

Due to traffic accidents, injuries, burns, congenital malformations and other reasons, a large number of patients with tissue or organ defects need urgent treatment every year. The shortage of donors, graft rejection and other problems cause a deficient supply for organ and tissue replacement, repair and regeneration of patients, so regenerative medicine came into being. Stem cell therapy plays an important role in the field of regenerative medicine, but it is difficult to fill large tissue defects by injection alone. The scientists combine three-dimensional (3D) printed bone tissue engineering scaffolds with stem cells to achieve the desired effect. These scaffolds can mimic the extracellular matrix (ECM), bone and cartilage, and eventually form functional tissues or organs by providing structural support and promoting attachment, proliferation and differentiation. This paper mainly discussed the applications of 3D printed bone tissue engineering scaffolds in stem cell regenerative medicine. The application examples of different 3D printing technologies and different raw materials are introduced and compared. Then we discuss the superiority of 3D printing technology over traditional methods, put forward some problems and limitations, and look forward to the future.

A Two-Scale Multi-Resolution Topologically Optimized Multi-Material Design of 3D Printed Craniofacial Bone Implants

Bone replacement implants for craniofacial reconstruction require to provide an adequate structural foundation to withstand the physiological loading. With recent advances in 3D printing technology in place of bone grafts using autologous tissues, patient-specific additively manufactured implants are being established as suitable alternates. Since the stress distribution of these structures is complicated, efficient design techniques, such as topology optimization, can deliver optimized designs with enhanced functionality. In this work, a two-scale topology optimization approach is proposed that provides multi-material designs for both macrostructures and microstructures. In the first stage, a multi-resolution topology optimization approach is used to produce multi-material designs with maximum stiffness. Then, a microstructure with a desired property supplants the solid domain. This is beneficial for bone implant design since, in addition to imparting the desired functional property to the design, it also introduces porosity. To show the efficacy of the technique, four different large craniofacial defects due to maxillectomy are considered, and their respective implant designs with multi-materials are shown. These designs show good potential in developing patient-specific optimized designs suitable for additive manufacturing.

Advanced technologies in periodontal tissue regeneration based on stem cells: Current status and future perspectives

Periodontitis is a progressive inflammation disease, the clinical management of which remains a challenge. The traditional management may control periodontal inflammation, but failed to regenerate functional periodontium. This review summarizes the most advancing regenerative techniques regarding stem cell culture and scaffold fabrication, such as cell sheeting, spheroid culture, electrospinning and 3D printing. The applications of different techniques manifest tremendous potential of regenerating the complete and functional periodontium. Albeit promising, new technologies have met with their own drawbacks such as insufficient vascularization and precision, which necessitate deeper modification. Thus, this review also points out the potential perspectives and methods aiming at their disadvantages, illuminating the directions of future researches to successful clinical scenarios.

Tissue Engineering of Oral Mucosa and Salivary Gland: Disease Modeling and Clinical Applications

Oral mucosa and salivary gland are composed of complex and dynamic networks of extracellular matrix, multiple cell types, vasculature, and various biochemical agents. Two-dimensional (2D) cell culture is commonly used in testing new drugs and experimental therapies. However, 2D cell culture cannot fully replicate the architecture, physiological, and pathological microenvironment of living human oral mucosa and salivary glands. Recent microengineering techniques offer state of the science cell culture models that can recapitulate human organ structures and functions. This narrative review describes emerging in vitro models of oral and salivary gland tissue such as 3D cell culture models, spheroid and organoid models, tissue-on-a-chip, and functional decellularized scaffolds. Clinical applications of these models are also discussed in this review.

In vivo bone regeneration assessment of offset and gradient melt electrowritten (MEW) PCL scaffolds

BACKGROUND

Biomaterial-based bone tissue engineering represents a promising solution to overcome reduced residual bone volume. It has been previously demonstrated that gradient and offset architectures of three-dimensional melt electrowritten poly-caprolactone (PCL) scaffolds could successfully direct osteoblast cells differentiation toward an osteogenic lineage, resulting in mineralization. The aim of this study was therefore to evaluate the in vivo osteoconductive capacity of PCL scaffolds with these different architectures.

METHODS

Five different calcium phosphate (CaP) coated melt electrowritten PCL pore sized scaffolds: 250 μm and 500 μm, 500 μm with 50% fibre offset (offset.50.50), tri layer gradient 250-500-750 μm (grad.250top) and 750-500-250 μm (grad.750top) were implanted into rodent critical-sized calvarial defects. Empty defects were used as a control. After 4 and 8 weeks of healing, the new bone was assessed by micro-computed tomography and immunohistochemistry.

RESULTS

Significantly more newly formed bone was shown in the grad.250top scaffold 8 weeks post-implantation. Histological investigation also showed that soft tissue was replaced with newly formed bone and fully covered the grad.250top scaffold. While, the bone healing did not happen completely in the 250 μm, offset.50.50 scaffolds and blank calvaria defects following 8 weeks of implantation. Immunohistochemical analysis showed the expression of osteogenic markers was present in all scaffold groups at both time points. The mineralization marker Osteocalcin was detected with the highest intensity in the grad.250top and 500 μm scaffolds. Moreover, the expression of the endothelial markers showed that robust angiogenesis was involved in the repair process.

CONCLUSIONS

These results suggest that the gradient pore size structure provides superior conditions for bone regeneration.

3D bioprinting and craniofacial regeneration

BACKGROUND

Considering the structural and functional complexity of the craniofacial tissues, 3D bioprinting can be a valuable tool to design and create functional 3D tissues or organs in situ for in vivo applications. This review aims to explore the various aspects of this emerging 3D bioprinting technology and its application in the craniofacial bone or cartilage regeneration.

METHOD

Electronic database searches were undertaken on pubmed, google scholar, medline, embase, and science direct for english language literature, published for 3D bioprinting in craniofacial regeneration. The search items used were 'craniofacial regeneration' OR 'jaw regeneration' OR 'maxillofacial regeneration' AND '3D bioprinting' OR 'three dimensional bioprinting' OR 'Additive manufacturing' OR 'rapid prototyping' OR 'patient specific bioprinting'. Reviews and duplicates were excluded.

RESULTS

Search with above described criteria yielded 476 articles, which reduced to 108 after excluding reviews. Further screening of individual articles led to 77 articles to which 9 additional articles were included from references, and 18 duplicate articles were excluded. Finally we were left with 68 articles to be included in the review.

CONCLUSION

Craniofacial tissue and organ regeneration has been reported a success using bioink with different biomaterial and incorporated stem cells in 3D bioprinters. Though several attempts have been made to fabricate craniofacial bone and cartilage, the strive to achieve desired outcome still continues.

Review of Plastic Surgery Biomaterials and Current Progress in Their 3D Manufacturing Technology

Plastic surgery is a broad field, including maxillofacial surgery, skin flaps and grafts, liposuction and body contouring, breast surgery, and facial cosmetic procedures. Due to the requirements of plastic surgery for the biological safety of materials, biomaterials are widely used because of its superior biocompatibility and biodegradability. Currently, there are many kinds of biomaterials clinically used in plastic surgery and their applications are diverse. Moreover, with the rise of three-dimensional printing technology in recent years, the macroscopically more precise and personalized bio-scaffolding materials with microporous structure have made good progress, which is thought to bring new development to biomaterials. Therefore, in this paper, we reviewed the plastic surgery biomaterials and current progress in their 3D manufacturing technology.

Biomimetic Nanofibrous 3D Materials for Craniofacial Bone Tissue Engineering

Repair of large bone defects using biomaterials-based strategies has been a significant challenge due to the complex characteristics required for tissue regeneration, especially in the craniofacial region. Tissue engineering strategies aimed at restoration of function face challenges in material selection, synthesis technique, and choice of bioactive factor release in combination with all aforementioned facets. Biomimetic nanofibrous (NF) scaffolds are attractive vehicles for tissue engineering due to their ability to promote endogenous bone regeneration by mimicking the shape and chemistry of natural bone extracellular matrix (ECM). To date, several techniques for generation of biomimetic NF scaffolds have been discovered, each possessing several advantages and drawbacks. This spotlight highlights two of the more popular techniques for biomimetic NF scaffold synthesis: electrospinning and thermally-induced phase separation (TIPS), covering development from inception in each technique as well as discussing the most recent innovations in each fabrication method.

Extending Cellulose-Based Polymers Application in Additive Manufacturing Technology: A Review of Recent Approaches

The materials for additive manufacturing (AM) technology have grown substantially over the last few years to fulfill industrial needs. Despite that, the use of bio-based composites for improved mechanical properties and biodegradation is still not fully explored. This limits the universal expansion of AM-fabricated products due to the incompatibility of the products made from petroleum-derived resources. The development of naturally-derived polymers for AM materials is promising with the increasing number of studies in recent years owing to their biodegradation and biocompatibility. Cellulose is the most abundant biopolymer that possesses many favorable properties to be incorporated into AM materials, which have been continuously focused on in recent years. This critical review discusses the development of AM technologies and materials, cellulose-based polymers, cellulose-based three-dimensional (3D) printing filaments, liquid deposition modeling of cellulose, and four-dimensional (4D) printing of cellulose-based materials. Cellulose-based AM material applications and the limitations with future developments are also reviewed.

Computational technology for nasal cartilage-related clinical research and application

Surgeons need to understand the effects of the nasal cartilage on facial morphology, the function of both soft tissues and hard tissues and nasal function when performing nasal surgery. In nasal cartilage-related surgery, the main goals for clinical research should include clarification of surgical goals, rationalization of surgical methods, precision and personalization of surgical design and preparation and improved convenience of doctor-patient communication. Computational technology has become an effective way to achieve these goals. Advances in three-dimensional (3D) imaging technology will promote nasal cartilage-related applications, including research on computational modelling technology, computational simulation technology, virtual surgery planning and 3D printing technology. These technologies are destined to revolutionize nasal surgery further. In this review, we summarize the advantages, latest findings and application progress of various computational technologies used in clinical nasal cartilage-related work and research. The application prospects of each technique are also discussed.

Selective laser sintering 3D printing - an overview of the technology and pharmaceutical applications

Food and Drug Administration (FDA) has approved a drug product (Spritam®) and many medical devices manufactured by three-dimensional printing (3DP) processes for human use. There is immense potential to print personalized medicines using 3DP. Many 3DP methods have been reported in the literature for pharmaceutical applications. However, selective laser sintering (SLS) printing has remained least explored for pharmaceutical applications. There are many advantages and challenges in adopting a SLS method for fabrication of personalized medicines. Solvent-free nature, availability of FDA approved thermoplastic polymer/excipients (currently used in hot melt-extrusion process), minimal/no post-processing step, etc. are some of the advantages of the SLS printing process. Major challenges of the technology are requirement of at least one thermoplastic component in the formulation and thermal stability of drug and excipients. This review provides an overview of the SLS printing method, excipient requirements, process monitoring, quality defects, regulatory aspects, and potential pharmaceutical applications.

Nanofibers as drug-delivery systems for infection control in dentistry

INTRODUCTION

Due to the complexity of different oral infections, new anti-infective nanotechnological approaches have been emerging for dentistry in recent years. These strategies may contribute to antimicrobial molecules delivery, tissue regeneration, and oral health maintenance by acting in a more specific site and not being cytotoxic. In this context, nanofibers appear as versatile structures and might act both in the release of antimicrobial molecules and as a scaffold for new tissue formation.

AREAS COVERED

This review addresses the application of different nanofibers as new strategies for the delivery of antimicrobial molecules for dentistry. Here, we present the main polymers used to construct nanofibers, methods of production and mainly their antimicrobial activity against microorganisms commonly responsible for the usual dental infections. These biomaterials may be associated to restorative materials, prostheses, and mucoadhesive structures. Besides, nanofibers can be used for endodontic or periodontal therapy, or even on implant surfaces.

EXPERT OPINION

A wide variety of studies report the potential application of anti-infective nanofibers in the oral cavity. Although there are still several barriers between in vitro and in vivo studies, these new formulations appear as promising new therapies for dentistry.

Editorial for the Special Issue on 3D Printing for Tissue Engineering and Regenerative Medicine

Three-dimensional (3D) bioprinting uses additive manufacturing techniques to fabricate 3Dstructures consisting of heterogenous selections of living cells, biomaterials, and active biomolecules[1,2] [...].

3D printing applications in bone tissue engineering

PURPOSE

3D printing technology provides an excellent capability to manufacture customised implants for patients. Now, its applications are also successful in bone tissue engineering. This paper tries to provide a review of the applications of 3D printing in bone tissue engineering.

METHODS

Searching by keywords, from the Scopus database, to identify relevant latest research articles on 3D printing in bone tissue engineering, through "3D printing" "bone tissue engineering". This study makes a bibliometric analysis of the identified research articles and identified major applications and steps.

RESULTS

3D printing technology creates innovative development in bone tissue engineering. It involves the manufacturing of a scaffold with the combination of cells and materials. We identified a total number of 257 research articles through bibliometric analysis by searching through keywords "3D printing" "bone tissue engineering". This paper studies 3D printing technology and its significant contributions, benefits and steps used for bone tissue engineering. Result discusses the essential elements of bone tissue engineering and identifies its five significant advancements when 3D printing is used. Finally, ten useful applications of 3D printing in bone tissue engineering are identified and studied with a brief description.

CONCLUSION

In orthopaedics, bone defects create a high impact on the quality of life of the patient. It leads to a higher demand for bone substitutes for replacement of bone defect. Bone tissue engineering can help to replace a critical defect bone. 3D printing is a useful technology for the fabrication of scaffolds critical in bone tissue engineering. There are different binders which can create bone scaffolds with requisite mechanical strength. These binders are used to create excellent osteoconductive, bioactive scaffolds. Computed tomography (CT) and Magnetic resonance imaging (MRI) help to provide images of specific defects of an individual patient, and these images can further be used for 3D printing the detective object. A bone defect caused by specific disease is sorted out by transplantation in clinical practice. Now a day bone tissue engineering opens a new option for this treatment of bone defects with the manufacturing of porous bone scaffold using 3D printing technology.

Stereolithographic 3D Printing for Deterministic Control over Integration in Dual-Material Composites

This work introduces a rapid and facile approach to predictably control integration between two materials with divergent properties. Programmed integration between photopolymerizable soft and stiff hydrogels was investigated for their promise in applications such as tissue engineering where heterogeneous properties are often desired. Spatial control afforded by grayscale 3D printing was leveraged to define regions at the interface that permit diffusive transport of a second material in-filled into the 3D printed part. The printing parameters (i.e., effective exposure dose) for the resin were correlated directly to mesh size to achieve controlled diffusion. Applying this information to grayscale exposures led to a range of distances over which integration was achieved with high fidelity. A prescribed finite distance of integration between soft and stiff hydrogels led to a 33% increase in strain to failure under tensile testing and eliminated failure at the interface. The feasibility of this approach was demonstrated in a layer-by-layer 3D printed part fabricated by stereolithography, which was subsequently infilled with a soft hydrogel containing osteoblastic cells. In summary, this approach holds promise for applications where integration of multiple materials and living cells is needed by allowing precise control over integration and reducing mechanical failure at contrasting material interfaces.