Portable electrochemical biosensor based on laser-induced graphene and MnO2 switch-bridged DNA signal amplification for sensitive detection of pesticide

Biosensor in smart food traceability system for food safety and security

The burden of food contamination and food wastage has significantly contributed to the increased prevalence of foodborne disease and food insecurity all over the world. Due to this, there is an urgent need to develop a smarter food traceability system. Recent advancements in biosensors that are easy-to-use, rapid yet selective, sensitive, and cost-effective have shown great promise to meet the critical demand for onsite and immediate diagnosis and treatment of food safety and quality control (i.e. point-of-care technology). This review article focuses on the recent development of different biosensors for food safety and quality monitoring. In general, the application of biosensors in agriculture (i.e. pre-harvest stage) for early detection and routine control of plant infections or stress is discussed. Afterward, a more detailed advancement of biosensors in the past five years within the food supply chain (i.e. post-harvest stage) to detect different types of food contaminants and smart food packaging is highlighted. A section that discusses perspectives for the development of biosensors in the future is also mentioned.

A stable colorimetric biosensor for highly selective detection of malathion residue in food based on aptamer-regulated laccase-mimic activity

Malathion causes a serious threat to human health due to its widespread use in the environment. Herein, a novel and stable smartphone-integrated colorimetric biosensor for malathion detection is firstly established based on aptamer-enhanced laccase-mimicking activity. The results indicate that the M17-F aptamer can increase the affinity of Ag2O nanoparticles to the substrate 2,4-dichlorophenol and enhance their laccase-mimicking activity. Thus, abundant semiquinone radicals are produced in the catalytic system, which are combined with chromogenic agent to generate dark red products. The corresponding RGB values for the colour change of the solution can be easily obtained using smartphones, which is used for the rapid detection of malathion. The established biosensor for malathion has a limit of detection as low as 5.85 nmol·L-1, and displays good selectivity for other competitive pesticides. Moreover, further studies have verified the applicability of the biosensor in actual samples, indicating that it may have the potential for application in malathion detection in food.

Label-free electrochemical sensing platform for sensitive detection of ampicillin by combining nucleic acid isothermal enzyme-free amplification circuits with CRISPR/Cas12a

The residue of ampicillin (AMP) in food and ecological environment poses a potential harm to human health. Therefore, a reliable system for detecting AMP is in great demand. Herein, a label-free and sensitive electrochemical sensor utilizing NH2-Co-MOF as an electrocatalytic active material for methylene blue (MB) was developed for rapid and facile AMP detection by combining hybridization chain reaction (HCR), catalytic hairpin assembly (CHA) with CRISPR/Cas12a. The surface of glassy carbon electrode modified with NH2-Co-MOF was able to undergo HCR independent of the AMP, forming long dsDNA complexes to load MB, resulting in strong original electrochemical signal. The presence of AMP could trigger upstream CHA circuit to activate the CRISPR/Cas12a system, thereby achieving rapid non-specific cleavage of the trigger ssDNA of HCR on the electrode surface, hindering the occurrence of HCR and reducing the load of MB. Significant signal change triggered by the target was ultimately obtained, thus achieving sensitive detection of the AMP with a detection limit as low as 1.60 pM (S/N = 3). The proposed sensor exhibited good stability, selectivity, and stability, and achieved reliable detection of AMP in milk and livestock wastewater samples, demonstrating its promising application prospects in food safety and environmental monitoring.

Cascade reaction triggered colorimetric array for identification of organophosphorus pesticides congeners

A modern agriculture uses alternative pest control methods to boost productivity, leading to an accumulation of organophosphorus (OPPs) congeners. This necessitates an intuitive and quick way to identify OPPs congeners. A colorimetric sensor for detecting OPPs congeners using a double-enzyme cascade reaction has been successfully designed and constructed in this study. The OPPs regulate the color changes induced by manganese dioxide nanoflowers (MnO2 NFs) and specific alkaline phosphatases (ALP) during the etching of gold nanopyramids (Au NBPs). The ascorbic acid (AA) produced by ALP hydrolysis inhibits Au NBPs etching by MnO2 NFs oxidized 3, 3', 5, 5'-tetramethylbenzidine (TMB). By inhibiting ALP catalytic activity, OPPs prevent AA formation. In this process, Au NBPs will undergo further etching, resulting in various colors so they can be analyzed semi-quantitatively with the naked eye. It has been found that different types of OPPs inhibit enzymes differently and therefore result in varying degrees of etching of Au NBPs. Principal Component Analysis (PCA) is performed by smart devices that convert R, G, and B signals into digital signals. This colorimetric array tests various foods (tea, apple, and cabbage). Colorimetric visualization sensors combined with data analysis will be used in real-life product development.

Development of reusable electrochemiluminescence sensing microchip for detection of vomitoxin

In this work, a reusable DNA sensing microchip was developed for detection of vomitoxin (deoxynivalenol, DON) in sorghum using Cd-based core-shell CdSe@CdS quantum dots (QDs) as promising electrochemiluminescence (ECL) emitter. The size-adjustable aqueous phase CdSe@CdS QDs were prepared through homogeneous method, exhibiting strong cathodic ECL emission with a central wavelength of 520 nm in S2O82- coreactant. And gold nanoparticles-modified iron cobalt cyanide hydrate (Fe-Co-Au) was introduced as an accelerator to amplify the ECL signal. ECL signal was quenched after the formation of a double-stranded (dsDNA) S1-S2 by generating an electron transfer system between the emitter and ferrocene (Fc), which are modified on the aptamer (ssDNA S1) and its complement sequence (ssDNA S2), respectively. When the target DON is presence, the aptamer ssDNA S1 will bind to the DON and trigger the unbinding of double strands DNA and the release of the ssDNA S2, thus the signal can be generated. This approach offers a feasible method for the detection of DON within the range of 1 ng/mL to 200 ng/mL.

Portable and Flexible Hydrogel Sensor for On-Site Atrazine Assay on Agricultural Products

There is growing attention focused toward the problems of ecological sustainability and food safety raised from the abuse of herbicides, which underscores the need for the development of a portable and reliable sensor for simple, rapid, and user-friendly on-site analysis of herbicide residues. Herein, a novel multifunctional hydrogel composite is explored to serve as a portable and flexible sensor for the facile and efficient analysis of atrazine (ATZ) residues. The hydrogel electrode is fabricated by doping graphite-phase carbon nitride (g-C3N4) into the aramid nanofiber reinforced poly(vinyl alcohol) hydrogel via a simple solution-casting procedure. Benefiting from the excellent electroactivity and large specific surface area of the solid nanoscale component, the prepared hydrogel sensor is capable of simple, rapid, and sensitive detection of ATZ with a detection limit down to 0.002 ng/mL and per test time less than 1 min. After combination with a smartphone-controlled portable electrochemical analyzer, the flexible sensor exhibited satisfactory analytical performance for the ATZ assay. We further demonstrated the applications of the sensor in the evaluation of the ATZ residues in real water and soil samples as well as the user-friendly on-site point-of-need detection of ATZ residues on various agricultural products. We envision that this flexible and portable sensor will open a new avenue on the development of next-generation analytical tools for herbicide monitoring in the environment and agricultural products.

Self-ratiometric fluorescent platform based on upconversion nanoparticles for on-site detection of chlorpyrifos

Monitoring organophosphorus pesticides is significant for food safety assessment. Herein, we developed upconversion nanoparticles (UCNPs)-based self-ratiometric fluorescent platform for the detection of chlorpyrifos. The UCNPs have the ability to confine the detection and reference functions in one nanoparticle. Specifically, the blue upconversion (UC) emission (448 nm) in the shell layer of UCNPs is quenched by the product of the acetylcholinesterase-mediated reaction, while the red UC emission (652 nm) from the core remains constant as a self-calibrated reference signal. Employing the inhibition property of chlorpyrifos, self-proportional fluorescence is employed to detect chlorpyrifos. As proof-of-concept, test strips are fabricated by loading the UCNPs onto filter paper. Combined with the smartphone and image-processing algorithm, chlorpyrifos quantitative testing is achieved with a detection limit of 14.4843 ng mL-1. This portable platform displays anti-interference capability and high stability in the complicated matrix, making it an effective candidate for on-site application.

Dual-source signal amplification electrochemiluminescence sensor combined with molecularly imprinted polymers for the imidacloprid detection

A novel lanthanide metal-organic-gel (MOG)-derived material/nitrogen-doped graphdiyne (Tb-Ru-MOG/CeO2/N-GDY) composite with a dual-source signal amplification strategy was prepared and used to construct a molecularly imprinted sensor based on bifunctional monomers for the detection of imidacloprid (IMI) using electrochemiluminescence (ECL). In a green reaction environment, terbium (III) (Tb3+) can undergo multiple coordination reactions with 4'-(4-carboxyphenyl)-2,2':6',2″-terpyridine (Hcptpy) and tris(4,4'-dicarboxylicacid-2,2'-bipyridyl) ruthenium (II) dichloride (Ru(dcbpy)32+), and combine with ceria nanoparticles (CeO2 NPs) to form Tb-Ru-MOG/CeO2. Within the Tb-Ru-MOG/CeO2 framework, energy transfer from the double ligands can sensitize the central Tb3+, triggering a distinct antenna effect and energy-transfer, and its polyporous configuration offered a nanoconfined space for Ce3+/Ce4+ to effectively catalyze coreactant radicals (S2O82-), leading to in-situ endogenous activation ECL reactions. The conductive N-GDY accelerated electron movement and increased the loading on the electrode surface, enhancing the exogenous excitation of the ECL signals. Leveraging the synergistic effect of the bifunctional monomer, the synthesized molecularly imprinted polymers (MIPs) ECL sensor demonstrated a wide detection range from 10 nM to 10,000 nM for IMI, with a limit of detection (LOD) of 1.37 nM, showcasing an innovative concept for the dual-source strategy of signal amplification in integrated ECL composites to analyze food and environmental hazards.

Foldable paper-based photoelectrochemical biosensor based on etching reaction of CoOOH nanosheets-coated laser-induced PbS/CdS/graphene for sensitive detection of ampicillin

Timely and rapid detection of antibiotic residues in the environment is conducive to safeguarding human health and promoting an ecological virtuous cycle. A foldable paper-based photoelectrochemical (PEC) sensor was successfully developed for the detection of ampicillin (AMP) based on glutathione/zirconium dioxide hollow nanorods/aptamer (GSH@ZrO2 HS@apt) modified cellulose paper as a reactive zone with laser direct-writing lead sulfide/cadmium sulfide/graphene (PbS/CdS/LIG) as photoelectrode and cobalt hydroxide (CoOOH) as a photoresist material. Initially, AMP was introduced into the paper-based reaction zone as a biogate aptamer, which specifically recognized the target and then left the ZrO2 HS surface, releasing glutathione (GSH) encapsulated inside. Subsequently, the introduction of GSH into the reaction region and etching of CoOOH nanosheets to expose the PbS/CdS/LIG photosensitive material increased photocurrent. Under optimal conditions, the paper-based PEC biosensor showed a linear response to AMP in the range of 5.0 - 2 × 104 pM with a detection limit of 1.36 pM (S/N = 3). In addition, the constructed PEC sensing platform has excellent selectivity, high stability and favorable reproducibility, and can be used to assess AMP residue levels in various real water samples (milk, tap water, river water), indicating its promising application in environmental antibiotic detection.

Paper-based electrochemical device for early detection of integrin αvβ6 expressing tumors

Despite progress in the prevention and diagnosis of cancer, current technologies for tumor detection present several limitations including invasiveness, toxicity, inaccuracy, lengthy testing duration and high cost. Therefore, innovative diagnostic techniques that integrate knowledge from biology, oncology, medicinal and analytical chemistry are now quickly emerging in the attempt to address these issues. Following this approach, here we developed a paper-based electrochemical device for detecting cancer-derived Small Extracellular Vesicles (S-EVs) in fluids. S-EVs were obtained from cancer cell lines known to express, at a different level, the αvβ6 integrin receptor, a well-established hallmark of numerous epithelial cancer types. The resulting biosensor turned out to recognize αvβ6-containing S-EVs down to a limit of 0.7*103 S-EVs/mL with a linear range up to 105 S-EVs /mL, and a relative standard deviation of 11%, thus it may represent a novel opportunity for αvβ6 expressing cancers detection.

PathoSense: a rapid electroanalytical device platform for screening Salmonella in water samples

Salmonella contamination is a major global health challenge, causing significant foodborne illness. However, current detection methods face limitations in sensitivity and time, which mostly rely on the culture-based detection techniques. Hence, there is an immediate and critical need to enhance early detection, reduce the incidence and impact of Salmonella contamination resulting in outbreaks. In this work, we demonstrate a portable non-faradaic, electrochemical sensing platform capable of detecting Salmonella in potable water with an assay turnaround time of ~ 9 min. We evaluated the effectiveness of this sensing platform by studying two sensor configurations: one utilizing pure gold (Au) and the other incorporating a semiconductor namely a zinc oxide thin film coated on the surface of the gold (Au/ZnO). The inclusion of zinc oxide was intended to enhance the sensing capabilities of the system. Through comprehensive experimentation and analysis, the LoD (limit of detection) values for the Au sensor and Au/ZnO sensor were 0.9 and 0.6 CFU/mL, respectively. In addition to sensitivity, we examined the sensing platform's precision and reproducibility. Both the Au sensor and Au/ZnO sensor exhibited remarkable consistency, with inter-study percentage coefficient of variation (%CV) and intra-study %CV consistently below 10%. The proposed sensing platform exhibits high sensitivity in detecting low concentrations of Salmonella in potable water. Its successful development demonstrates its potential as a rapid and on-site detection tool, offering portability and ease of use. This research opens new avenues for electrochemical-based sensors in food safety and public health, mitigating Salmonella outbreaks and improving water quality monitoring.

Electrochemical detection of glutathione based on accelerated CRISPR/Cas12a trans-cleavage with MnO2 nanosheets

The CRISPR/Cas12a system is accelerated by glutathione-mediated reduction of MnO2 nanosheets. By monitoring the trans-cleavage of the DNA probe, an electrochemical method for glutathione assay is fabricated, with the detection limit of 3.5 pM. It provides a promising tool for plasma analysis with satisfactory performance, indicating the broad application prospects of this glutathione assay.

Constructed MXene matrix composites as sensing material and applications thereof: A review

Most studies on MXene matrix composites for sensor development have primarily focused on synthesis and application. Nevertheless, there is currently a lack of research on how the introduction of different materials affects the sensing properties of these composites. The rapid development of MXene has raised intriguing questions about improving sensor performance by combining MXene with other materials such as polymers, metals and inorganic non-metals. This review will concentrate on the construction of MXene-based composites and explore ways to enhance their sensor applications. Specifically, this review describes why the introduction of materials to the system brings the advantage of low concentration and high sensitivity assays, as well as the MXene-based frameworks that have been recently investigated. Lastly, in order to capture the current trend of MXene-based composites in sensor applications and identify promising research directions, this review will critically evaluate the potential applications of newly developed MXene systems.

Spatiotemporal control of DNAzyme activity for fluorescent imaging of telomerase RNA in living cells

BACKGROUND

Human telomerase is a ribonucleoprotein complex that includes proteins and human telomerase RNA (hTR). Emerging evidence suggested that the expression level of hTR was high related with the development of tumor, so it is important to accurately detect the content of hTR. Optical control of DNAzyme activity shows a promising strategy for precise biosensing, biomedical imaging and modulation of biological processes. Although DNAzyme-based sensors can be controlled spatiotemporally by light, its application in the detection of hTR in living cells is still rare. Therefore, designing DNAzyme activity spatiotemporal controllable sensors for hTR detection is highly needed.

RESULTS

We developed a UV light-activated DNAzyme-based nanoprobe for spatially accurate imaging of intracellular hTR. The proposed nanoprobe was named MDPH, which composed of an 8-17 DNAzyme (D) inactivated by a protector strand (P), a substrate strand (H), and MnO2 nanosheets. The MnO2 nanosheets can enhance the cellular uptake of DNA strands, so that MDPH probe can enter cells autonomously through endocytosis. Under the high concentration of GSH in cancer cells, MnO2 nanosheets can self-generate cofactors to maintain the catalytic activity of DNAzyme. When exposing UV light and in presence of target hTR, DNAzyme could cleave substrate H, resulting in the recovery of fluorescence of the system. The cells imaging results show that MDPH probe could be spatiotemporally controlled to image endogenous hTR in cancer cells.

SIGNIFICANCE

With this design, telomerase RNA-specific fluorescent imaging was achieved by MDPH probe in both cancer and normal cells. Our probe made a promising new platform for spatiotemporal controllable intracellular hTR monitoring. This current method can be applied to monitor a variety of other biomarkers in living cells and perform medical diagnosis, so it may has broad applications in the field of medicine.

Novel molecularly imprinted nanogel modified microfluidic paper-based SERS substrate for simultaneous detection of bisphenol A and bisphenol S traces in plastics

Paper-based surface-enhanced Raman scattering (SERS) optical nanoprobes provide ultrasensitive analyte detection; however, they lack selectivity, making them difficult to use in real-world sample analysis without a pretreatment process. This work describes the design of a microfluidic paper-based SERS substrate based on molecularly imprinted nanogels decorated with silver nanoparticles to simultaneously detect bisphenol A (BPA) and bisphenol S (BPS) traces in plastic toys and receipts. The synthesized nanogels have two characteristics that boost SERS performance: molecularly imprinted cavities that allow for selective adsorption and a wrinkled surface that creates uniformly distributed hot spots. Simple paper-based sensor devices were built as 'drop and read' SERS substrates with a separate reservoir to detect a single target, while advanced SERS platforms were designed as a microfluidic chip with two reservoirs connected by a channel for simultaneous detection of BPA and BPS. The SERS platform with a single reservoir showed outstanding analytical performance for the detection of BPA and BPS, with low detection limits of 0.38 pM and 0.37 pM, respectively. The microfluidic paper-based sensor allowed simultaneous and selective detection of BPA and BPS with detection limits estimated at 0.68 nM and 0.47 nM, respectively. The developed sensors are successfully applied to detect BPA and BPS in plastic products and receipts. Finally, the results obtained with our method showed greater sensitivity than those of commercially available ELISA kits, and the acquired values within the ELISA detection range were in excellent agreement.

In situ formation of fluorescence species for the detection of alkaline phosphatase and organophosphorus pesticide via the ascorbate oxidase mimetic activity of AgPd bimetallic nanoflowers

Sensitive detection strategies for enzymes and their inhibitors not only have critical significance in clinical diagnosis but can be extended to food and environment analysis. Here, bimetallic AgPd alloy nanoflowers were synthesized using carbon dots as the reductant via a two-step reduction method. The AgPd bimetallic nanoflowers exhibit ascorbate oxidase mimetic activity, which can rapidly catalyze the oxidization of ascorbic acid to dehydroascorbic acid (DHA). The DHA can then react with o-phenylenediamine (OPD) to produce 3-(1, 2-dihydroxyethyl)furo[3,4-b] quinoxalin-1(3H)-one (DFQ), accompanying with the characteristic fluorescence peak at 440 nm for DFQ. Alkaline phosphatase catalyzes l-ascorbyl-2-phosphate to generate AA, while organic phosphorus pesticides (OPPs) such as chlorpyrifos can inhibit the activity of alkaline phosphatase. By utilizing the enzyme-nanozyme tandem catalytic reaction, the fluorescence of the system varies in the presence of different concentrations of ALP or OPPs, which can be used to detect ALP in serum and OPPs in vegetables and fruits.

Nanobioengineered surface comprising carbon based materials for advanced biosensing and biomedical application

Carbon-based nanomaterials (CNMs) are at the cutting edge of materials science. Due to their distinctive architectures, substantial surface area, favourable biocompatibility, and reactivity to internal and/or external chemico-physical stimuli, carbon-based nanomaterials are becoming more and more significant in a wide range of applications. Numerous research has been conducted and still is going on to investigate the potential uses of carbon-based hybrid materials for diverse applications such as biosensing, bioimaging, smart drug delivery with the potential for theranostic or combinatorial therapies etc. This review is mainly focused on the classifications and synthesis of various types of CNMs and their electroanalytical application for development of efficient and ultra-sensitive electrochemical biosensors for the point of care diagnosis of fatal and severe diseases at their very initial stage. This review is mainly focused on the classification, synthesis and application of carbon-based material for biosensing applications. The integration of various types of CNMs with nanomaterials, enzymes, redox mediators and biomarkers have been used discussed in development of smart biosensing platform. We have also made an effort to discuss the future prospects for these CNMs in the biosensing area as well as the most recent advancements and applications which will be quite useful for the researchers working across the globe working specially in biosensors field.

Recent Study Advances in Flexible Sensors Based on Polyimides

With the demand for healthy life and the great advancement of flexible electronics, flexible sensors are playing an irreplaceably important role in healthcare monitoring, wearable devices, clinic treatment, and so on. In particular, the design and application of polyimide (PI)-based sensors are emerging swiftly. However, the tremendous potential of PI in sensors is not deeply understood. This review focuses on recent studies in advanced applications of PI in flexible sensors, including PI nanofibers prepared by electrospinning as flexible substrates, PI aerogels as friction layers in triboelectric nanogenerator (TENG), PI films as sensitive layers based on fiber Bragg grating (FBG) in relative humidity (RH) sensors, photosensitive PI (PSPI) as sacrificial layers, and more. The simple laser-induced graphene (LIG) technique is also introduced in the application of PI graphitization to graphene. Finally, the prospect of PIs in the field of electronics is proposed in the review.

Label-Free, Impedance-Based Biosensor for Kidney Disease Biomarker Uromodulin

We demonstrate the development of a label-free, impedance-based biosensor by using a passivation layer of 50-nm tantalum pentoxide (Ta2O5) on interdigitated electrodes (IDE). This layer was fabricated by atomic layer deposition (ALD) and has a high dielectric constant (high-κ), which improves the capacitive property of the IDE. We validate the biosensor's performance by measuring uromodulin, a urine biomarker for kidney tubular damage, from artificial urine samples. The passivation layer is functionalized with uromodulin antibodies for selective binding. The passivated IDE enables the non-faradaic impedance measurement of uromodulin concentrations with a measurement range from 0.5 ng/mL to 8 ng/mL and with a relative change in impedance of 15 % per ng/mL at a frequency of 150 Hz (log scale). This work presents a concept for point-of-care biosensing applications for disease biomarkers.

A review of biosensor for environmental monitoring: principle, application, and corresponding achievement of sustainable development goals

Human health/socioeconomic development is closely correlated to environmental pollution, highlighting the need to monitor contaminants in the real environment with reliable devices such as biosensors. Recently, variety of biosensors gained high attention and employed as in-situ application, in real-time, and cost-effective analytical tools for healthy environment. For continuous environmental monitoring, it is necessary for portable, cost-effective, quick, and flexible biosensing devices. These benefits of the biosensor strategy are related to the Sustainable Development Goals (SDGs) established by the United Nations (UN), especially with reference to clean water and sources of energy. However, the relationship between SDGs and biosensor application for environmental monitoring is not well understood. In addition, some limitations and challenges might hinder the biosensor application on environmental monitoring. Herein, we reviewed the different types of biosensors, principle and applications, and their correlation with SDG 6, 12, 13, 14, and 15 as a reference for related authorities and administrators to consider. In this review, biosensors for different pollutants such as heavy metals and organics were documented. The present study highlights the application of biosensor for achieving SDGs. Current advantages and future research aspects are summarized in this paper.Abbreviations: ATP: Adenosine triphosphate; BOD: Biological oxygen demand; COD: Chemical oxygen demand; Cu-TCPP: Cu-porphyrin; DNA: Deoxyribonucleic acid; EDCs: Endocrine disrupting chemicals; EPA: U.S. Environmental Protection Agency; Fc-HPNs: Ferrocene (Fc)-based hollow polymeric nanospheres; Fe₃O₄@3D-GO: Fe₃O₄@three-dimensional graphene oxide; GC: Gas chromatography; GCE: Glassy carbon electrode; GFP: Green fluorescent protein; GHGs: Greenhouse gases; HPLC: High performance liquid chromatography; ICP-MS: Inductively coupled plasma mass spectrometry; ITO: Indium tin oxide; LAS: Linear alkylbenzene sulfonate; LIG: Laser-induced graphene; LOD: Limit of detection; ME: Magnetoelastic; MFC: Microbial fuel cell; MIP: Molecular imprinting polymers; MWCNT: Multi-walled carbon nanotube; MXC: Microbial electrochemical cell-based; NA: Nucleic acid; OBP: Odorant binding protein; OPs: Organophosphorus; PAHs: Polycyclic aromatic hydrocarbons; PBBs: Polybrominated biphenyls; PBDEs: Polybrominated diphenyl ethers; PCBs: Polychlorinated biphenyls; PGE: Polycrystalline gold electrode; photoMFC: photosynthetic MFC; POPs: Persistent organic pollutants; rGO: Reduced graphene oxide; RNA: Ribonucleic acid; SDGs: Sustainable Development Goals; SERS: Surface enhancement Raman spectrum; SPGE: Screen-printed gold electrode; SPR: Surface plasmon resonance; SWCNTs: single-walled carbon nanotubes; TCPP: Tetrakis (4-carboxyphenyl) porphyrin; TIRF: Total internal reflection fluorescence; TIRF: Total internal reflection fluorescence; TOL: Toluene-catabolic; TPHs: Total petroleum hydrocarbons; UN: United Nations; VOCs: Volatile organic compounds.

Effects of additives on the performance of a laser-induced graphene sensor modified with ZrO2 nanoparticles for OP detection

In this study, a simple and portable electrochemical sensor based on laser-induced graphene (LIG) has been developed to systematically investigate the feasibility of LIG as an electrode to detect organophosphorus pesticides (OPs). It proves that the LIG-based electrode has a relatively high electrochemically active surface area (ECSA) and heterogeneous electron transfer (HET) of 0.100 cm2 and 0.000825 cm s-1, respectively. In addition, zirconium dioxide nanoparticles (ZrO2 NPs) have been modified on the electrode with three different binders, β-cyclodextrin (β-CD), chitosan (CS) and Nafion, to improve the adsorption capacity of the electrode toward OPs, and the effect of the binders on the performance of the as-fabricated sensor has been investigated in detail. The results show that β-CD increases not only the electrochemically active surface area of the electrode but also the redox peak current of methyl parathion (MP). To evaluate the sensitivity of the sensor, differential pulse voltammetry (DPV) curves have been tested in solutions containing different concentrations of MP using ZrO2-β-CD/LIG as an electrode, which shows a detection range of 5-200 ng ml-1 and a detection limit of 0.89 ng ml-1. In summary, the LIG-based sensor has a low detection limit, high sensitivity and good interference resistance, and thus has tremendous potential for the detection of pesticides in the environment.

Electrochemical nucleic acid sensors: Competent pathways for mobile molecular diagnostics

Electrochemical nucleic acid biosensor has demonstrated great promise in clinical diagnostic tests, mainly because of its flexibility, high efficiency, low cost, and easy integration for analytical applications. Numerous nucleic acid hybridization-based strategies have been developed for the design and construction of novel electrochemical biosensors for diagnosing genetic-related diseases. This review describes the advances, challenges, and prospects of electrochemical nucleic acid biosensors for mobile molecular diagnosis. Specifically, the basic principles, sensing elements, applications in diagnosis of cancer and infectious diseases, integration with microfluidic technology and commercialization are mainly included in this review, aiming to provide new insights and directions for the future development of electrochemical nucleic acid biosensors.

Strategies and Applications of Graphene and Its Derivatives-Based Electrochemical Sensors in Cancer Diagnosis

Graphene is an emerging nanomaterial increasingly being used in electrochemical biosensing applications owing to its high surface area, excellent conductivity, ease of functionalization, and superior electrocatalytic properties compared to other carbon-based electrodes and nanomaterials, enabling faster electron transfer kinetics and higher sensitivity. Graphene electrochemical biosensors may have the potential to enable the rapid, sensitive, and low-cost detection of cancer biomarkers. This paper reviews early-stage research and proof-of-concept studies on the development of graphene electrochemical biosensors for potential future cancer diagnostic applications. Various graphene synthesis methods are outlined along with common functionalization approaches using polymers, biomolecules, nanomaterials, and synthetic chemistry to facilitate the immobilization of recognition elements and improve performance. Major sensor configurations including graphene field-effect transistors, graphene modified electrodes and nanocomposites, and 3D graphene networks are highlighted along with their principles of operation, advantages, and biosensing capabilities. Strategies for the immobilization of biorecognition elements like antibodies, aptamers, peptides, and DNA/RNA probes onto graphene platforms to impart target specificity are summarized. The use of nanomaterial labels, hybrid nanocomposites with graphene, and chemical modification for signal enhancement are also discussed. Examples are provided to illustrate applications for the sensitive electrochemical detection of a broad range of cancer biomarkers including proteins, circulating tumor cells, DNA mutations, non-coding RNAs like miRNA, metabolites, and glycoproteins. Current challenges and future opportunities are elucidated to guide ongoing efforts towards transitioning graphene biosensors from promising research lab tools into mainstream clinical practice. Continued research addressing issues with reproducibility, stability, selectivity, integration, clinical validation, and regulatory approval could enable wider adoption. Overall, graphene electrochemical biosensors present powerful and versatile platforms for cancer diagnosis at the point of care.

A label-free electrochemical aptasensor based on Bi-Sb alloy materials for potential POCT of HER-2

As a prognostic biomarker for breast cancer, human epidermal growth factor receptor 2 (HER-2) is of crucial diagnostic value. Here, a label-free electrochemical aptasensor was established for the ultrasensitive detection of HER-2 using a modified electrode of Bi-Sb alloy materials (Bi-Sb AMs). The performance of the aptasensor was enhanced greatly due to the introduction of Bi-Sb alloy materials (Bi-Sb AMs) with high conductivity. Furthermore, by integrating the aptasensor with the Sensit Smart U-disk electrochemical analyzer, the point-of-care testing (POCT) for HER-2 was realized. Under the optimal experimental parameters, the POCT analyzer showed a wide linear response from 0.01 pg mL-1 to 100 ng mL-1, with a low detection limit (LOD) of 5.96 fg mL-1 for the detection of HER-2. The presented POCT analyzer exhibited good specificity, stability, and reproducibility. Benefiting from the simple operation and rapid testing, the developed analyzer will have potential application in the prognostic diagnosis and treatment of breast cancer.

Defective zirconium/titanium bimetallic metal-organic framework as a highly selective and sensitive electrochemical aptasensor for deoxynivalenol determination in foodstuffs

An electrochemical aptsensor for deoxynivalenol determination was successfully designed and constructed based on a defective bimetallic organic framework (denoted as ZrTi-MOF). The high porosity, large specific surface area, several structural defects, mixed metal clusters, and rich functionality of ZrTi-MOF markedly enhanced its electrochemical activity and facilitated the aptamer immobilization. As a result, the ZrTi-MOF-based aptasensor shows high sensitivity to detect deoxynivalenol via specific recognition between aptamer and deoxynivalenol, as well as the formation of aptamer-deoxynivalenol complex. On this basis, the developed ZrTi-MOF-based impedimetric aptasensor showed a low detection limit of 0.24 fg mL-1 for deoxynivalenol determination in the deoxynivalenol concentration range 1 fg mL-1- 1 ng mL-1 under optimized conditions, which also exhibited satisfactory selectivity, stability, reproducibility, and regenerability. Furthermore, determination of deoxynivalenol was achieved in bread and wheat flour samples via the developed ZrTi-MOF-based deoxynivalenol aptasensor. The result from this study showed that the ZrTi-MOF-based electrochemical aptasensor could become a promising strategy for detecting deoxynivalenol in foodstuffs in the future.

Advances in Microfluidics Techniques for Rapid Detection of Pesticide Residues in Food

Food safety is a significant issue that affects people worldwide and is tied to their lives and health. The issue of pesticide residues in food is just one of many issues related to food safety, which leave residues in crops and are transferred through the food chain to human consumption. Foods contaminated with pesticide residues pose a serious risk to human health, including carcinogenicity, neurotoxicity, and endocrine disruption. Although traditional methods, including gas chromatography, high-performance liquid chromatography, chromatography, and mass spectrometry, can be used to achieve a quantitative analysis of pesticide residues, the disadvantages of these techniques, such as being time-consuming and costly and requiring specialist staff, limit their application. Therefore, there is a need to develop rapid, effective, and sensitive equipment for the quantitative analysis of pesticide residues in food. Microfluidics is rapidly emerging in a number of fields due to its outstanding strengths. This paper summarizes the application of microfluidic techniques to pyrethroid, carbamate, organochlorine, and organophosphate pesticides, as well as to commercial products. Meanwhile, the study also outlines the development of microfluidics in combination with 3D printing technology and nanomaterials for detecting pesticide residues in food.

A visualized sensor based on layered double hydroxides with peroxidase-like activity for sensitive acetylcholinesterase assay

Acetylcholinesterase (AChE) plays a crucial role in biological neurotransmission. The aberrant expression of AChE is associated with various neurodegenerative diseases. Therefore, it is of great significance to develop a simple and highly sensitive AChE analysis platform. Herein, a simple colorimetric sensor was constructed for sensitive detection of AChE based on the peroxidase-like catalytic activity of Ni/Co layered double hydroxides (Ni/Co LDHs). In this sensor, the fabricated Ni/Co LDHs possess high peroxidase-like activity, enabling rapid catalysis of o-phenylenediamine (OPD) to produce yellow oxOPD in the presence of H₂O₂. This peroxidase-like activity of Ni/Co LDHs was found to be effectively inhibited by the presence of AChE. It is speculated that the combination of AChE on the outer surface of Ni/Co LDHs through non-covalent interaction may cover the active sites and hinder their adsorption to the substrates, leading to the failure of OPD oxidation. As a result, the yellow color from oxOPD is related to the AChE concentration, enabling the direct AChE assay in an equipment-free manner. In addition, the fabricated Ni/Co LDHs could be modified on a paper surface to obtain a paper-based analytical device for visualized colorimetric detection of AChE. The as-proposed sensor shows high sensitivity to AChE with a detection limit down to 6.6 μU mL^-1. Therefore, this naked-eye paper-based sensor is capable of on-site and real-time detection of AChE, and has outstanding application prospects in clinical diagnosis and biomedical fields.

Solid-state, reagent-free and one-step laser-induced synthesis of graphene-supported metal nanocomposites from metal leaves and application to glucose sensing

The laser-induced method to prepare three-dimensional (3D) porous graphene has been widely used in many fields owing to its low-cost, easy operation, maskless patterning and ease of mass production. Metal nanoparticles are further introduced on the surface of 3D graphene to enhance its property. The existing methods, however, such as laser irradiation and electrodeposition of metal precursor solution, suffer from many shortcomings, including complicated procedure of metal precursor solution preparation, strict experimental control, and poor adhesion of metal nanoparticles. Herein, a solid-state, reagent-free, and one-step laser-induced strategy has been developed for the fabrication of metal nanoparticle modified-3D porous graphene nanocomposites. Commercial transfer metal leaves were covered on a polyimide film followed by direct laser irradiation to produce 3D graphene nanocomposites modified with metal nanoparticles. The proposed method is versatile and applicable to incorporate various metal nanoparticles including gold silver, platinum, palladium, and copper. Furthermore, the 3D graphene nanocomposites modified with AuAg alloy nanoparticles were successfully synthesized in both 21 Karat (K) and 18K gold leaves. Its electrochemical characterization demonstrated that the synthesized 3D graphene-AuAg alloy nanocomposites exhibited excellent electrocatalytic properties. Finally, we fabricated LIG-AuAg alloy nanocomposites as enzyme-free flexible sensors for glucose detection. The LIG-18K electrodes exhibited the superior glucose sensitivity of 1194 μA mM^-1 cm^-2 and low detection limits of 0.21 μM. The LIG-21K nanocomposite sensors showed two linear ranges from 1 μM to 1 mM and 2 mM-20 mM with good sensitivity. Furthermore, the flexible glucose sensor showed good stability, sensitivity, and ability to sense in blood plasma samples. The proposed one-step fabrication of reagent-free and metal alloy nanoparticles on LIG with excellent electrochemical performance opens up possibilities for diversifying potential applications of sensing, water treatment and electrocatalysis.

Facile colorimetric smartphone-based biosensor for rapid detection of organophosphorus pesticides residues in environment using the aptamer-enhanced oxidase activity of octahedral Ag2O particles

The long-term and excessive use of organophosphorus pesticides (OPs) leads to hazardous residues in the environment, which threatens human health to a considerable extent. Colorimetric methods can quickly and readily identify pesticide residue, but they still have various challenges in accuracy and stability. Herein, a smartphone-assisted and non-enzymatic colorimetric biosensor was constructed for rapid monitoring of multiple OPs based on the enhanced effect of aptamer on the catalytic ability of octahedral Ag₂O. It was demonstrated that the aptamer sequence could enhance the affinity of colloidal Ag₂O to chromogenic substrates, and accelerate the generation of oxygen radicals such as superoxide radical (·O₂^-) and singlet oxygen (¹O₂) from dissolved oxygen, thereby significantly increasing the oxidase activity of octahedral Ag₂O. The color change of the solution can be easily converted to the corresponding RGB values by a smartphone for quantitative and rapid detection of multiple OPs. Hence, the smartphone-based and visual biosensor of multiple OPs was acquired with limit of detection of 10 μg L^-1, 28 μg L^-1 and 40 μg L^-1 for isocarbophos, profenofos and omethoate, respectively. The colorimetric biosensor also exhibited good recoveries in several environmental and biological samples, showing that it may have broad application prospects for detecting OPs residues.

Feather-like Gold Nanostructures Anchored onto 3D Mesoporous Laser-Scribed Graphene: A Highly Sensitive Platform for Enzymeless Glucose Electrochemical Detection in Neutral Media

The authors present a novel sensing platform for a disposable electrochemical, non-enzymatic glucose sensor strip at physiological pH. The sensing material is based on dendritic gold nanostructures (AuNs) resembling feather branches, which are electrodeposited onto a laser-scribed 3D graphene electrode (LSGE). The LSGEs were fabricated via a one-step laser scribing process on a commercially available polyimide sheet. This study investigates several parameters that influence the morphology of the deposited Au nanostructures and the catalytic activity toward glucose electro-oxidation. The electrocatalytic activity of the AuNs-LSGE was evaluated using cyclic voltammetry (CV), linear sweep voltammetry (LSV), and amperometry and was compared to commercially available carbon electrodes prepared under the same electrodeposition conditions. The sensor demonstrated good stability and high selectivity of the amperometric response in the presence of interfering agents, such as ascorbic acid, when a Nafion membrane was applied over the electrode surface. The proposed sensing strategy offers a wide linear detection range, from 0.5 to 20 mM, which covers normal and elevated levels of glucose in the blood, with a detection limit of 0.21 mM. The AuNs-LSGE platform exhibits great potential for use as a disposable glucose sensor strip for point-of-care applications, including self-monitoring and food management. Its non-enzymatic features reduce dependence on enzymes, making it suitable for practical and cost-effective biosensing solutions.

A Sensitive Biosensor Based on Plasmonic-Graphene Configuration for Detection of COVID-19 Virus

In this paper, four individual structures based on graphene-plasmonic nano combinations are proposed for detection of corona viruses and especially COVID-19. The structures are arranged based on arrays in the shapes of half-sphere and one-dimensional photonic crystal formats. The half-sphere and plate shaped layers are made of Al, Au, SiO2 and graphene. The one-dimensional photonic crystals lead the wavelength and peak corresponding to the absorption peak to lower and higher amounts, respectively. In order to improve the functionality of the proposed structures, effects of structural parameters and chemical potentials are considered. A defect layer of GZO is positioned in the middle of one-dimensional photonic crystal layers to shift the absorption's peak wavelength to the appropriate wavelength range for diagnosing corona viruses (~300 nm to 600 nm). The last proposed structure is considered as a refractive bio-sensor for detection of corona viruses. In the final proposed structure (based on different layers of Al, Au, SiO2, GZO and graphene), corona viruses are considered as the biomolecule layer and the results are obtained. The proposed bio-sensor can be a good and functional candidate for detection of corona viruses and especially COVID-19 in photonic integrated circuits with the satisfying sensitivity of ~664.8 nm/RIU (refractive index unit).

A visual diagnostic detection of Helicobacter pylori and the gastric carcinoma-related virulence genes (cagA and vacA) by a fluorescent loop-mediated isothermal amplification (LAMP)

Helicobacter pylori (H. pylori) infection has increasingly been a serious problem worldwide. The H. pylori infection can result in a series of stomach diseases including gastric carcinoma. There are two specific virulence genes (cagA and vacA) of H. pylori that are closely related to the occurrence of gastric cancer, and the common molecular detection methods (PCR, qPCR) are not suitable for high-screening test due to the requirement of expensive instruments and well-trained personals. Herein, we develop a rapid visual assay based on loop-mediated isothermal amplification (LAMP) for detecting H. pylori and its major virulence genes (cagA, vacAs1 and vacAm1) to guide clinical treatment for H. pylori infection. In this research, a fluorescent LAMP assay was established by optimizing the indicator of MnCl₂-Calcein, so that the resulted color and fluorescence changes could be utilized to perform the visual detection for H. pylori and its virulence genes with high sensitivity (10^-3 ng/μL). The proposed LAMP assay is simple, fast (30 min) and capable in providing more sensitive results than traditional methods in the test of 46 clinical biopsy samples. By detecting the three virulence genes together, we can profile the infection risk of the patients, and discuss the correlation among the genes. Moreover, the method could be used to diagnose virulently infected individuals and benefit the eradication of H. pylori in early warning for gastric cancer.

Integration of on-chip lysis and paper-based sensor for rapid detection of viral and exosomal RNAs

In recent years, paper-based nucleic acid sensors have been demonstrated for the ability to detect DNA and RNA molecules extracted from viruses and bacteria. In clinical samples, these nucleic acids are mostly encapsulated in lipid membranes and need to be released before being analyzed using paper-based sensors. For the nucleic acid amplification tests (NAATs), it is also desirable to remove the interfering molecules that can inhibit the nucleic acid amplification. To achieve a field deployable NAAT, we report a portable sensor system that combines the thermolysis and paper-based NAATs to detect target RNA molecules carried by viral and exosomal nanoparticles. The sensor cartridge includes a lysis chamber with a pressure-controlled diaphragm valve, paper flow channels, and three paper-based NAAT reaction chambers to extract, transport, and detect nucleic acids respectively. A compact instrument was prototyped to automate the assay, collect fluorescence images of the nucleic acid amplification, and generate amplification curves for NAATs. The pump-free and paper-based sensor achieved quantitative analysis of influenza A virus (IAV) RNA and exosome microRNA within 1 h, with the lowest detect concentration of 10⁴ TCID₅₀/mL and 10⁶ EV/mL for IAV and exosome, respectively. Owing to the advantages of easy storage, simple operation, and low cost, such as system has great potential to be used as a point-of-care test for in-field diagnosis of viral and bacterial infections.

A novel photoelectrochemical array platform for ultrasensitive multiplex detection and subtype identification of HPV genes

The rapid, low-cost and user-friendly methods for nucleic acid detection is urgently needed. Here we developed a miniaturized and convenient photoelectrochemical biosensor array (PEBA) platform for multiplexing and simultaneous detection of nucleic acid. The array system containing nine sensing units was integrated on one piece of conductive glass by laser etching and screen printing. Moreover, human papillomavirus (HPV), the main cause of cervical cancer, was selected as the model marker to evaluate the applicability of the fabricated PEBA. The proposed PEBA for HPV genotyping involved the TiO₂@Au nanoparticles (NPs) as the photoelectrochemical (PEC) material and CdS quantum dots (CdS QDs)-labeled DNA hairpin probe anchored on the TiO₂@Au NPs as the recognition element. With the addition of HPV target, the probe undergoes a significant conformational change and forces CdS QDs away from TiO₂@Au, resulting in decreased PEC signals. The established array platform coupled with nucleic acid amplification exhibited high sensitivity as low as 0.1 copies/μL and a linear range of 0.6-600 copies/μL for nine HPV genotyping. Method evaluation with 40 clinical samples including 20 HPV-positive and 20 negative samples, gave a 97.5% concordance result in comparison with commercial kits. The genotyping results obtained by the PEBA reveal that HPV52, HPV18, and HPV11 are the most prevalent genotypes in positive samples, which is in good concordance with the official report concerning the trend of HPV prevalence among women with cervical lesions in Shenzhen. The designed PEBA platform has potential applications in extensive fields like biomedicine analysis and clinical healthcare diagnosis.

Transition metal-doped germanium oxide nanozyme with enhanced enzyme-like activity for rapid detection of pesticide residues in water samples

Designing highly active nanozymes for bioanalysis and environmental sensing remains a challenge. In this study, transition metal, palladium (Pd) and iron (Fe), doped germanium oxide (GeO₂) nanozyme was designed and optimized. Compared with the pristine GeO₂ nanozyme, the transition metal doped GeO₂ nanozyme have lower Michaelis-Menten constants and higher catalytic activity, indicating that the Pd and Fe doped GeO₂ nanozyme not only enhance their affinity for the substrate but also improve its catalytic activity. In addition, a colorimetric sensor based on the GeO₂@Pd-H₂O₂-TMB system was constructed for the visual detection of simazine in water samples due to the good affinity between TMB and simazine. This sensor has good selectivity and sensitivity with a detection limit of 6.21 μM because of the highest catalytic performance of GeO₂@Pd nanozyme. This study broadens the application of nanozymes in environmental field and other nanozymes can also be enhanced in activity by simple transition metal doping.

How safe is our food we eat? An electrochemical lab-on-kitchen approach towards combinatorial testing for pesticides and GMOs; A case study with edamame

In our daily life, as consumers we are constantly made aware of the impact of pesticides and other modifications to food products derived from genetically modified organisms (GMO's) that have an impact on human health. In our connected world, there is an immense interest for on-demand information about food quality prior to consumption. The gold standard method to detect pesticides or GMOs residues in food is complex and is not amenable to rapid consumer use. In this study, we demonstrate the feasibility of an electrochemical portable sensing approach for the simultaneous direct detection of spiked pesticides chlorpyrifos (Chlp) and GMOs protein Cry1Ab in real edamame soy matrix. The immunoassay based two-plex sensing platform was fabricated using respective antibody's Chlp on one side and Cry1Ab on other side. A simple lab-on-kitchen level preparation of matrix has been demonstrated and sensor response was tested using non-faradaic electrochemical impedance spectroscopy (EIS), which showed a linear response in Cry1Ab/Chlp concentrations from 0.3 ng/mL to 243 ng/mL with limit of detection 0.3 ng /mL for both the target antigens (Cry1Ab and Chlp) respectively. The spiked and recovery test results fall within ± 20% error in real sample matrix which demonstrates the performance of the our platform with maximum residue limit (MRL) for the given targets. Such electrochemical portable multi-analyte direct sensing tool with simple matrix processing protocol can be a future commercial field-testing tool for use at everyday consumer level.

A wireless smartphone-based "tap-and-detect" formaldehyde sensor with disposable nano-palladium grafted laser-induced graphene (nanoPd@LIG) electrodes

We developed a fully integrated smart sensing device for on-site testing of food to detect trace formaldehyde (FA). A nano-palladium grafted laser-induced graphene (nanoPd@LIG) composite was synthesized by one-step laser irradiation of a Pd²⁺-chitosan-polyimide precursor. The composite was synthesized in the form of a three-electrode sensor on a polymer substrate. The electrochemical properties and morphology of the fabricated composite were characterized and the electrochemical kinetics of FA oxidation at the nanoPd@LIG electrode were investigated. The nanoPd@LIG electrode was combined with a smart electrochemical sensing (SES) device to determine FA electrochemically. The proposed SES device uses near field communication (NFC) to receive power and transfer data between a smartphone interface and a battery-free sensor. The proposed FA sensor exhibited a linear detection range from 0.01 to 4.0 mM, a limit of detection of 6.4 μM, good reproducibility (RSDs between 2.0 and 10.1%) and good anti-interference properties for FA detection. The proposed system was used to detect FA in real food samples and the results correlated well with the results from a commercial potentiostat and a spectrophotometric analysis.

Advanced visual sensing techniques for on-site detection of pesticide residue in water environments

Pesticide usage has increased to fulfil agricultural demand. Pesticides such as organophosphorus pesticides (OPPs) are ubiquitous in world food production. Their widespread usage has unavoidable detrimental consequences for humans, wildlife, water, and soil environments. Hence, the development of more convenient and efficient pesticide residue (PR) detection methods is of paramount importance. Visual detecting approaches have acquired a lot of interest among different sensing systems due to inherent advantages in terms of simplicity, speed, sensitivity, and eco-friendliness. Furthermore, various detections have been proven to enable real-life PR surveillance in environment water. Fluorometric (FL), colourimetric (CL), and enzyme-inhibition (EI) techniques have emerged as viable options. These sensing technologies do not need complex operating processes or specialist equipment, and the simple colour change allows for visual monitoring of the sensing result. Visual sensing techniques for on-site detection of PR in water environments are discussed in this paper. This paper further reviews prior research on the integration of CL, FL, and EI-based techniques with nanoparticles (NPs), quantum dots (QDs), and metal-organic frameworks (MOFs). Smartphone detection technologies for PRs are also reviewed. Finally, conventional methods and nanoparticle (NPs) based strategies for the detection of PRs are compared.

Specific lateral flow detection of isothermal nucleic acid amplicons for accurate point-of-care testing

For point-of-care testing (POCT), coupling isothermal nucleic acid amplification schemes (e.g., recombinase polymerase amplification, RPA) with lateral flow assay (LFA) readout is an ideal platform, since such integration offers both high sensitivity and deployability. However, isothermal schemes typically suffers from non-specific amplification, which is difficult to be differentiated by LFA and thus results in false-positives. Here, we proposed an accurate POCT platform by specific recognition of target amplicons with peptide nucleic acid (PNA, assisted by T7 Exonuclease), which could be directly plugged into the existing RPA kits and commercial LFA test strips. With SARS-CoV-2 as the model, the proposed method (RPA-TeaPNA-LFA) efficiently eliminated the false-positives, exhibiting a lowest detection concentration of 6.7 copies/μL of RNA and 90 copies/μL of virus. Using dual-gene (orf1ab and N genes of SARS-CoV-2) as the targets, RPA-TeaPNA-LFA offered a high specificity (100%) and sensitivity (RT-PCR Ct < 31, 100%; Ct < 40, 71.4%), and is valuable for on-site screening or self-testing during isolation. In addition, the dual test lines in the test strips were successfully explored for simultaneous detection of SARS-CoV-2 and H1N1, showing great potential in response to future pathogen-based pandemics.

Detection of SARS-CoV-2 in clinical and environmental samples using highly sensitive reduced graphene oxide (rGO)-based biosensor

Quantitative RT-PCR (qRT-PCR) is the most commonly used diagnostic tool for SARS-CoV-2 detection during the COVID-19 pandemic. Despite its sensitivity and accuracy, qRT-PCR is a time-consuming method that requires expensive laboratories with highly trained personnel. In this work, on-site detection of SARS-CoV-2 in municipal wastewater was investigated for the first time. The wastewater was unprocessed and did not require any prefiltration, prior spiking with virus, or viral concentration in order to be suitable for use with the biosensor. The prototype reported here is a reduced graphene oxide (rGO)-based biosensor for rapid, sensitive and selective detection of SARS-CoV-2. The biosensor achieved a limit of detection (LOD) of 0.5 fg/mL in phosphate-buffered saline (PBS) and exhibited specificity when exposed to various analytes. The response time was measured to be around 240 ms. To further explore the capabilities of the biosensor in real clinical and municipal wastewater samples, three different tests were performed to determine the presence or absence of the virus: (i) qRT-PCR, (ii) a rapid antigen-based commercially available test (COVID-19 Test Strips), and (iii) the biosensor constructed and reported here. Taken together, our results demonstrate that a biosensor that can detect SARS-CoV-2 in clinical samples as well as unfiltered and unprocessed municipal wastewater is feasible.

Disposable Electrochemical Sensors for Highly Sensitive Detection of Chlorpromazine in Human Whole Blood Based on the Silica Nanochannel Array Modified Screen-Printed Carbon Electrode

Rapid and highly sensitive quantitative analysis of chlorpromazine (CPZ) in human whole blood is of great importance for human health. Herein, we utilize the screen-printed carbon electrodes (SPCE) as the electrode substrates for growth of highly electroactive and antifouling nanocomposite materials consisting of vertically ordered mesoporous silica films (VMSF) and electrochemically reduced graphene oxide (ErGO) nanosheets. The preparation of such VMSF/ErGO/SPCE could be performed by using an electrochemical method in a few seconds and the operation is controllable. Inner ErGO layer converted from graphene oxide (GO) in the growth process of VMSF provides oxygen-containing groups and two-dimensional π-conjugated planar structure for stable fabrication of outer VMSF layer. Owing to the π-π enrichment and excellent electrocatalytic abilities of ErGO, electrostatic preconcentration and antifouling capacities of VMSF, and inherent disposable and miniaturized properties of SPCE, the proposed VMSF/ErGO/SPCE sensor could be applied for quantitative determination of CPZ in human whole blood with high accuracy and sensitivity, good stability, and low sample consumption.

Significance of an Electrochemical Sensor and Nanocomposites: Toward the Electrocatalytic Detection of Neurotransmitters and Their Importance within the Physiological System

A prominent neurotransmitter (NT), dopamine (DA), is a chemical messenger that transmits signals between one neuron to the next to pass on a signal to and from the central nervous system (CNS). The imbalanced concentration of DA may cause numerous neurological sicknesses and syndromes, for example, Parkinson's disease (PD) and schizophrenia. There are many types of NTs in the brain, including epinephrine, norepinephrine (NE), serotonin, and glutamate. Electrochemical sensors have offered a creative direction to biomedical analysis and testing. Researches are in progress to improve the performance of sensors and develop new protocols for sensor design. This review article focuses on the area of sensor growth to discover the applicability of polymers and metallic particles and composite materials as tools in electrochemical sensor surface incorporation. Electrochemical sensors have attracted the attention of researchers as they possess high sensitivity, quick reaction rate, good controllability, and instantaneous detection. Efficient complex materials provide considerable benefits for biological detection as they have exclusive chemical and physical properties. Due to distinctive electrocatalytic characteristics, metallic nanoparticles add fascinating traits to materials that depend on the material's morphology and size. Herein, we have collected much information on NTs and their importance within the physiological system. Furthermore, the electrochemical sensors and corresponding techniques (such as voltammetric, amperometry, impedance, and chronoamperometry) and the different types of electrodes' roles in the analysis of NTs are discussed. Furthermore, other methods for detecting NTs include optical and microdialysis methods. Finally, we show the advantages and disadvantages of different techniques and conclude remarks with future perspectives.

Electrospinning-Based Biosensors for Health Monitoring

In recent years, many different biosensors are being used to monitor physical health. Electrospun nanofiber materials have the advantages of high specific surface area, large porosity and simple operation. These properties play a vital role in biosensors. However, the mechanical properties of electrospun nanofibers are poor relative to other techniques of nanofiber production. At the same time, the organic solvents used in electrospinning are generally toxic and expensive. Meanwhile, the excellent performance of electrospun nanofibers brings about higher levels of sensitivity and detection range of biosensors. This paper summarizes the principle and application of electrospinning technology in biosensors and its comparison with other technologies.

Fluorescent Detection of Two Pesticides Based on CRISPR-Cas12a and Its Application for the Construction of Four Molecular Logic Gates

An intelligent detection platform was developed through molecular logic gate operation based on CRISPR-Cas12a and signal amplification circuits using two kinds of pesticides [acetamiprid (ACE) and atrazine (ATR)] as inputs. The pesticide-aptamer bindings activate the signal amplification process to produce numerous double-stranded DNA, which can be identified by CRISPR-Cas12a. Under the optimal assay conditions, the sensor exhibits excellent analytical performance, with the detection limits for ACE and ATR of 2.5 and 0.2 pM, respectively. The practicality of the platform was verified by testing pesticide concentrations in food samples. Several molecular logic gates (OR, AND, XOR, and INHIBIT) were constructed using "0" and "1" to encode the target pesticides and the fluorescence readout. The logic detection platform with simple operation, high sensitivity, and multiple logic functions is promising to become a powerful sensing system for the intelligent assay of different pesticides in food samples.

Electrochemical Signal Amplification Strategies and Their Use in Olfactory and Taste Evaluation

Biosensors are powerful analytical tools used to identify and detect target molecules. Electrochemical biosensors, which combine biosensing with electrochemical analysis techniques, are efficient analytical instruments that translate concentration signals into electrical signals, enabling the quantitative and qualitative analysis of target molecules. Electrochemical biosensors have been widely used in various fields of detection and analysis due to their high sensitivity, superior selectivity, quick reaction time, and inexpensive cost. However, the signal changes caused by interactions between a biological probe and a target molecule are very weak and difficult to capture directly by using detection instruments. Therefore, various signal amplification strategies have been proposed and developed to increase the accuracy and sensitivity of detection systems. This review serves as a reference for biosensor and detector research, as it introduces the research progress of electrochemical signal amplification strategies in olfactory and taste evaluation. It also discusses the latest signal amplification strategies currently being employed in electrochemical biosensors for nanomaterial development, enzyme labeling, and nucleic acid amplification techniques, and highlights the most recent work in using cell tissues as biosensitive elements.