Improving Dielectric Properties of PVDF Composites by Employing Surface Modified Strong Polarized BaTiO₃ Particles Derived by Molten Salt Method

Structural, Mechanical, and Barrier Properties of the Polyvinylidene Fluoride-Bacterial Nanocellulose-Based Hybrid Composite

This study presents an analysis of films which consist of two layers; one layer is PVDF as the matrix, along with fillers BaTiO3 (BT), and the second is one bacterial nanocellulose (BNC) filled with Fe3O4. The mass fraction of BT in PVDF was 5%, and the samples were differentiated based on the duration of the mechanical activation of BT. This innovative PVDF laminate polymer with environmentally friendly fillers aligns with the concept of circular usage, resulting in a reduction in plastic content and potential improvement of the piezoelectric properties of the entire composite. This work presents new, multifunctional "green" packaging materials that potentially could be a good alternative to specific popular materials used for this purpose. The synthesis of the films was carried out using the hot press method. Tensile tests, water vapor permeability examination, and structural analyses using SEM-EDS and FTIR have been conducted. The sample PVDF/BT20/BNC/Fe3O4 exhibited the best barrier properties (impermeability to water vapor), while the highest tensile strength and toughness were exhibited by the PVDF/BT5/BNC/Fe3O4 sample.

Significantly Enhanced Balance of Dielectric Properties of Polyvinylidene Difluoride Three-Phase Composites by Silver Deposited on K2Ni0.93Ti7.07O16 Hollandite Nanoparticles

Three-phase polymer composites are promising materials for creating electronic device components. The qualitative and quantitative composition of such composites has a significant effect on their functional, in particular dielectric properties. In this study, ceramic filler K2Ni0.93Ti7.07O16 (KNTO) with Ag coating as conductive additive (0.5, 1.0, 2.5 wt.%) was introduced into the polyvinylidene difluoride (PVDF) polymer matrix in amounts of 7.5, 15, 22.5, and 30 vol.%. to optimize the dielectric constant and dielectric loss tangent. The filler was characterized by X-ray phase analysis, Fourier-transform infrared spectroscopy and Scanning electron microscopy methods. The dielectric constant, dielectric loss tangent, and conductivity of three-phase composites KNTO@Ag-PVDF were studied in comparison with two-phase composites KNTO-PVDF in the frequency range from 102 Hz to 106 Hz. The dielectric constant values of composites containing 7.5, 15, 22.5, and 30 vol.% filler were 12, 13, 17.4, 19.2 for pure KNTO and 13, 19, 25, 31 for KNTO@Ag filler (2.5 wt.%) at frequency 10 kHz. The dielectric loss tangent ranged from 0.111 to 0.340 at a filler content of 7.5 to 30 vol.%. A significantly enhanced balance of dielectric properties of PVDF-based composites was found with K2Ni0.93Ti7.07O16 as ceramic filler for 1 wt.% of silver. Composites KNTO@Ag(1 wt.%)-PVDF can be applied as dielectrics for passive elements of flexible electronics.

Electroactive properties and piezo-tribo hybrid energy harvesting performances of PVDF-AlFeO3 composites: role of crystal symmetry and agglomeration of fillers

Inorganic filler-loaded PVDF-based composites have been very widely used for electrical and energy harvesting applications in recent times. In this regard, the effects of different parameters of fillers like size, shape, chemical states, distribution, functional properties, and many others on the output performance of PVDF have been widely studied. However, the effect of another important parameter, namely the crystal symmetry of the filler, in tuning the energy harvesting performance of PVDF has been rarely explored. Therefore, to explore this fact, here we develop PVDF-based composite films by using two types of AlFeO3 fillers, one with rhombohedral R3̄c symmetry (AFRH) and another with an orthorhombic Pc21n structure. Ferrite-based oxides have been chosen here as fillers due to their good dielectric compatibility with PVDF. On the other hand, AlFeO3 has been chosen due to the simplicity of synthesizing it with both centrosymmetric and non-centrosymmetric crystal structures and the scarcity of reports exploring the energy-harvesting performance of AlFeO3-based polymer composites. A significant difference in particle agglomeration has also been observed here between the mentioned two types of AlFeO3 fillers which was mainly due to their specific synthesis conditions. The electroactive properties of PVDF have been observed to be mostly dependent on filler agglomeration. However, the crystal symmetry has shown a strong effect on the piezoelectric energy harvesting performances. As a result of these facts, the piezo-tribo hybrid energy harvesting performance, which depends on both the dielectric permittivity and piezoelectric activity, has been observed to be better for the AFRH5-based hybrid device (AFRH5H) (with ∼72 V open circuit voltage and ∼45 μW cm-2 power density) compared to that of the AFOR5-based hybrid device (AFOR5H). The real-life applications of all the energy harvesting devices have also been demonstrated here.

Giant flexoelectric response of uniformly dispersed BT-PVDF composite films induced by SDS-assisted treatment

Polymer-ceramic composites are commonly used as flexoelectric films. In existing studies, the flexoelectric effect of composites are generally improved by adjusting the material structures or adding ferroelectric materials. Further improvement of flexoelectric response has encountered a bottleneck. Considering from a new perspective, this study innovatively proposes to prepare the uniformly dispersed BT-PVDF composite films with giant flexoelectric response by surfactant SDS-assisted treatment. According to the engineering applications, tilt sensors have been fabricated with the SDS/BT-PVDF composite films. The prepared tilt sensors can accurately sense the tilt change in a small-angle range (0-10°) between the coaxial connecting parts, the response signal changes significantly (49.25-72.35 mV/°), and the response speed can reach 0.166 s. The research provides a new idea for improving the flexoelectric response and also paves a way for developing tilt sensors through a low-cost, facile, and reliable method, showing potential applications including bending sensing and structural health monitoring.

Dielectric and energy storage properties of surface-modified BaTi0.89Sn0.11O3@polydopamine nanoparticles embedded in a PVDF-HFP matrix

In the most recent electronic and electric sectors, ceramic-polymer nanocomposites with high dielectric permittivity and energy density are gaining popularity. However, the main obstacle to improving the energy density in flexible nanocomposites, besides the size and morphology of the ceramic filler, is the low interfacial compatibility between the ceramic and the polymer. This paper presents an alternative solution to improve the dielectric permittivity and energy storage properties for electronic applications. Here, the poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) matrix is filled with surface-modified BaTi0.89Sn0.11O3/polydopamine nanoparticles (BTS11) nanoparticles, which is known for exhibiting multiphase transitions and reaching a maximum dielectric permittivity at room temperature. BTS11 nanoparticles were synthesized by a sol-gel/hydrothermal method at 180 °C and then functionalized by polydopamine (PDA). As a result, the nanocomposites exhibit dielectric permittivity (εr) of 46 and a low loss tangent (tan δ) of 0.017 at 1 kHz at a relatively low weight fraction of 20 wt% of BTS11@PDA. This is approximately 5 times higher than the pure PVDF-HFP polymer and advantageous for energy storage density in nanocomposites. The recovered energy storage for our composites reaches 134 mJ cm-3 at an electric field of 450 kV cm-1 with a high efficiency of 73%. Incorporating PDA-modified BTS11 particles into the PVDF-HFP matrix demonstrates highly piezo-active regions associated with BTS11 particles, significantly enhancing functional properties in the polymer nanocomposites.

The Preparation, Structural Design, and Application of Electroactive Poly(vinylidene fluoride)-Based Materials for Wearable Sensors and Human Energy Harvesters

Owing to their biocompatibility, chemical stability, film-forming ability, cost-effectiveness, and excellent electroactive properties, poly(vinylidene fluoride) (PVDF) and PVDF-based polymers are widely used in sensors, actuators, energy harvesters, etc. In this review, the recent research progress on the PVDF phase structures and identification of different phases is outlined. Several approaches for obtaining the electroactive phase of PVDF and preparing PVDF-based nanocomposites are described. Furthermore, the potential applications of these materials in wearable sensors and human energy harvesters are discussed. Finally, some challenges and perspectives for improving the properties and boosting the applications of these materials are presented.

Quantum Composites with Charge-Density-Wave Fillers

A unique class of advanced materials-quantum composites based on polymers with fillers composed of a van der Waals quantum material that reveals multiple charge-density-wave quantum condensate phases-is demonstrated. Materials that exhibit quantum phenomena are typically crystalline, pure, and have few defects because disorder destroys the coherence of the electrons and phonons, leading to collapse of the quantum states. The macroscopic charge-density-wave phases of filler particles after multiple composite processing steps are successfully preserved in this work. The prepared composites display strong charge-density-wave phenomena even above room temperature. The dielectric constant experiences more than two orders of magnitude enhancement while the material maintains its electrically insulating properties, opening a venue for advanced applications in energy storage and electronics. The results present a conceptually different approach for engineering the properties of materials, extending the application domain for van der Waals materials.

Role of Microstructures in the Dielectric Properties of PVDF-Based Nanocomposites Containing High-Permittivity Fillers for Energy Storage

Polymer-based nanocomposites containing inorganic ferroelectric inclusions, typically ABO₃ perovskites, have emerged as innovative dielectric materials for energy storage and electric insulation, potentially coupling the high breakdown strength (BDS) and easy processing of polymers with the enhancement of dielectric constant provided by the ferroelectric phase. In this paper, experimental data and three-dimensional finite element method (3D FEM) simulations were combined to shed some light on the effect of microstructures on the dielectric properties of poly(vinylidene fluoride) (PVDF)-BaTiO₃ composites. The existence of particle aggregates or touching particles has a strong effect on the effective dielectric constant and determines an increase of the local field in the neck region of the ferroelectric phase with a detrimental effect on the BDS. The distribution of the field and the effective permittivity are very sensitive to the specific microstructure considered. The degradation of the BDS can be overcome by coating the ferroelectric particles with a thin shell of an insulating oxide with a low dielectric constant, such as SiO₂ (ε_r = 4). The local field is highly concentrated on the shell, while the field in the ferroelectric phase is reduced almost to zero and that on the matrix is close to the applied one. The electric field in the matrix becomes less homogeneous with increasing the dielectric constant of the shell material, as happens with TiO₂ (ε_r = 30). These results provide a solid background to explain the enhanced dielectric properties and the superior BDS of composites containing core-shell inclusions.

Influence of Ferroelectric Filler Size and Clustering on the Electrical Properties of (Ag-BaTiO3)-PVDF Sub-Percolative Hybrid Composites

The paper presents a study concerning the role of ferroelectric filler size and clustering in the dielectric properties of 20%BaTiO₃-80%PVDF and of 20% (2%Ag-98%BaTiO₃)-PVDF hybrid nanocomposites. By finite element calculations, it was shown that using fillers with ε > 10³ does not provide a permittivity rise in the composites and the effective dielectric constant tends to saturate to specific values determined by the filler size and agglomeration degree. Irrespective of the ferroelectric filler sizes, the addition of metallic ultrafine nanoparticles (Ag) results in permittivity intensification and the effect is even stronger if the metallic nanoparticles are connected to a higher degree with the ferroelectric particles' surfaces. When using coarse ferroelectric fillers, the probability of clustering is higher, thus favoring the permittivity increase by field concentration in small regions close to the interfaces separating dissimilar materials. The modeling results were validated by an experimental dielectric analysis performed in a series of PVDF-based thick films with the same amount of BaTiO₃ fillers or with Ag-BaTiO₃ hybrid fillers. Similar trends as predicted by simulations were found experimentally but with slightly higher permittivity values which were assigned to the modifications of the polymer phase composition due to the presence of nanofillers and the local sample inhomogeneity (the presence of clustering, in particular for coarse BaTiO₃ grains), which create regions with enhanced local fields.

Interface modified BTO@PS-co-mah/PS composite dielectrics with enhanced breakdown strength and ultralow dielectric loss

Dielectrics of the polymer-matrix composite are considered to present combined advantages from both the polymer matrix and inorganic fillers. However, the breakdown strength, as well as energy density, is not effectively enhanced due to the poor compatibility between the organic and inorganic components. Herein, polymer composites derived from polystyrene (PS) and barium titanate (BTO) are proposed and beneficial interface modification by poly(styrene-co-maleic anhydride) (PS-co-mah) is conducted to improve compatibility between the inorganic filler and polymer matrix. The results show that the BTO@PS-co-mah/PS composites, in which the interfacial layer of PS-co-mah would undergo chemical reactions with the aminated BTO and blend PS matrix with excellent physical compatibility, exhibit enhanced breakdown strength and declined dielectric loss compared with both pure PS and BTO/PS without interfacial modulation. Particularly, the BTO@PS-co-mah/PS composite with 5 wt% filler content indicates optimized performance with an E _b of 507 MV m^-1 and tan δ of 0.085%. It is deduced that the deep energy traps introduced by the PS-co-mah layer would weaken the local electric field and suppress the space charge transporting so as to optimize the performance of composites. Consequently, the interfacial-modified BTO@PS-co-mah/PS would present great potential for applications, such as film capacitors.

Enhanced piezoelectric response in BTO NWs-PVDF composite through tuning of polar phase content

We have fabricated a flexible, environment friendly piezoelectric nanogenerator (PENG) based on the ferroelectric Polyvinylidene fluoride (PVDF) composite incorporated with Barium titanate (BaTiO₃) nanowires (NWs) of piezoelectric coefficientd₃₃ = 308 pm V^-1. The single-layered PENG can deliver output power density of 10μW cm^-2and an output voltage of 2 V with a nominal mechanical load of 1 kPa. BaTiO₃(BTO) NWs of different concentrations were incorporated into PVDF to tune the polar phase content, internal resistance, and optimize the output power. We show that there exists a critical value of BTO NWs loading of 15 wt%, beyond which the piezoelectric energy harvesting characteristics of the PVDF nanocomposites decrease. The oxygen vacancies present in the BTO NWs surface attract the fluorine ions of PVDF chain and favour the formation ofβphase. The enhanced value of dielectric constant and dielectric loss of BTO-PVDF samples in the low frequency region suggest strong interfacial polarization in the composite system. The fabricated PENG can charge a super-capacitor up to 4 V within 35 s. The origin of the high power output from the BTO (15 wt%)-PVDF composite is attributed to the combined effect of enhanced polar phase content, strong interfacial polarization, and reduced internal resistance. This study provides an effective pathway in enhancing the performance of BTO-PVDF based piezoelectric energy harvesters.

High-Dielectric PVP@PANI/PDMS Composites Fabricated via an Electric Field-Assisted Approach

Polymer-based composite films with multiple properties, such as low dielectric loss tangent, high dielectric constant, and low cost are promising materials in the area of electronics and electric industries. In this study, flexible dielectric films were fabricated via an electric field-assisted method. Polyaniline (PANI) was modified by polyvinylpyrrolidone (PVP) to form a core–shell structure to serve as functional particles and silicone rubber polydimethylsiloxane (PDMS) served as the matrix. The dielectric constant of the composites prepared under electric fields was improved by the micro-structures formed by external electric fields. With the addition of 2.5 wt% PVP@PANI, the dielectric constant could be significantly enhanced, up to 23; the dielectric loss tangent is only 1, which is lower than that of the aligned PANI samples. This new processing technology provides important insights for aligning fillers in polymer matrix to form composites with enhanced dielectric properties.

Lead-Free Perovskite Cs3Bi2I9-Derived Electroactive PVDF Composite-Based Piezoelectric Nanogenerators for Physiological Signal Monitoring and Piezo-Phototronic-Aided Strain Modulated Photodetectors

In recent years, lead-free perovskite materials are exponentially emerging in photovoltaic and optoelectronic applications due to their low toxicity and superior optical properties. On the other hand, the demand for flexible, wearable, and lightweight optoelectronic devices is significantly growing in sensor and actuator technologies. In this scenario, lead-free perovskite-based flexible piezoelectric polymer composites have sparked considerable attention in this field due to their excellent piezo-, pyro-, ferroelectric, and photovoltaic properties. Thus, in this work, a long-term stable lead-free Cs₃Bi₂I₉-PVDF composite is introduced. The in situ growth of the Cs₃Bi₂I₉ perovskite induces 92% yield of the electroactive phase in the PVDF matrix. The possible mechanism behind the electroactive β-phase transformation is presented via interfacial interactions of PVDF moieties with the Cs₃Bi₂I₉ (CBI) perovskite, which also give rise to long-term environmental stability. Next, a piezoelectric nanogenerator (PNG) has been fabricated with the Cs₃Bi₂I₉-PVDF composite for mechanical energy harvesting, biophysiological motion monitoring, and voice recognitions that have potential utility in the health-care sector. Furthermore, a photodetector is developed to realize the piezo-phototronic effect. It exhibits a fast photoswitching behavior with rise and decay times of 141 and 278 ms, respectively. Thus, it is confirmed that the flexible Cs₃Bi₂I₉-PVDF composite has shown tremendous potential to be used as an optical signal-modulated piezo-responsive wearable sensor.

Defect-Induced Self-Poling in a W18O49/PVDF Piezoelectric Energy Harvester

W₁₈O₄₉ nanostructures, previously used for electrocatalysis, energy storage, electrochromic, and gas sensing applications, are incorporated in poly(vinylidene fluoride) (PVDF) in this work for mechanical energy-harvesting applications. X-ray diffraction spectroscopy (XRD), high-resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, differential scanning calorimetry (DSC), and the polarization-electric (P-E) field loop test prompts the addition of W₁₈O₄₉ nanorods in PVDF nucleates and stabilizes the piezoelectric polar γ-phase in the nanocomposite. Electrochemical experiments were employed for the first time to relate the event of the evolution of crystalline phases in PVDF to the transfer of electrons to the electrolyte from PVDF using the data from cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). High dielectric constant (ε') and low dielectric loss (ε″) values were obtained proportionately for different weight percentage additions of W₁₈O₄₉ nanorods in PVDF. DSC was employed to study the crystallization kinetics of γ-phase evolution. Piezoresponse force microscopy (PFM) was used to compare the piezoelectric responses from the PVDF nanocomposites. The W₁₈O₄₉/PVDF nanocomposite could generate a peak open circuit voltage of ∼6 V and a peak short circuit current of ∼700 nA. The W₁₈O₄₉/PVDF nanocomposite could light two commercial blue-light-emitting diodes (LEDs) with hand impulse imparting.

High-energy-density polymer dielectrics via compositional and structural tailoring for electrical energy storage

Dielectric capacitors with higher working voltage and power density are favorable candidates for renewable energy systems and pulsed power applications. A polymer with high breakdown strength, low dielectric loss, great scalability, and reliability is a preferred dielectric material for dielectric capacitors. However, their low dielectric constant limits the polymer to achieve satisfying energy density. Therefore, great efforts have been made to get high-energy-density polymer dielectrics. By compositional and structural tailoring, the synergic integrations of the multiple components and optimized structural design effectively improved the energy storage properties. This review presents an overview of recent advancements in the field of high-energy-density polymer dielectrics via compositional and structural tailoring. The surface/interfacial engineering conducted on both microscale and macroscale for polymer dielectrics is the focus of this review. Challenges and the promising opportunities for the development of polymer dielectrics for capacitive energy storage applications are presented at the end of this review.

•

A detailed summary of the state-of-the-art polymer dielectrics

•

The comparison of polymer nanocomposites with 0D, 1D, and 2D nanofillers

•

Analyzing high U_e polymer dielectrics via compositional and structural tailoring

•

Summary of micro- or macro-surface and interface engineering

Triboelectric Enhancement of Polyvinylidene Fluoride Membrane Using Magnetic Nanoparticle for Water-Based Energy Harvesting

Produced by magnetic material dispersed in a viscous environment for the purpose of collecting and converting energy, magnetic rheological compounds greatly strengthen the development of skin-attachable and wearable electrical equipment. Given that magnetic nanomaterial anisotropy has a substantial influence on the interface polarizing of polyvinylidene fluoride (PVDF), it is critical to explore the function of magnetic polymer compounds in the triboelectric layer of triboelectric nanogenerator (TENG) output power. In this study, ferromagnetic cobalt ferrite, CoFe₂O₄ (CFO), nanoparticles, and PVDF were employed to create a triboelectric composite membrane to improve TENG energy output. The content of β phase in PVDF increased significantly from 51.2% of pure PVDF membrane to 77.7% of 5 wt% CFO nanoparticles in the PVDF matrix, which further increase the dielectric constant and negative charge of the membrane. As a consequence, the energy output of CFO/PVDF-5 TENG increased significantly with a voltage of 17.2 V, a current of 2.27 μA, and a power density of 90.3 mW/m², which is 2.4 times the performance of pure PVDF TENG. Finally, the proposal for TENG hopes that its extraordinary stability and durability will provide additional views on hydrodynamic power generation in the future.

Polyvinylidene Fluoride Surface Polarization Enhancement for Liquid-Solid Triboelectric Nanogenerator and Its Application

Liquid-solid triboelectric nanogenerator (TENG) has been great attention as a promising electricity generation method for renewable energy sources and self-powered electronic devices. Thus, enhancing TENG performance is a critical issue to be concerned for both practical and industrial applications. Hence in this study, a high-output liquid-solid TENG is proposed using a polyvinylidene fluoride surface polarization enhancement (PSPE) for self-powered streamflow sensing, which shows many advantages, such as adapt to the sensor energy requirement, multiple parameters sensing at the same time, eliminate the influence of ion concentration. The TENG based on PSPE film has the maximum power density of 15.6 mW/m², which is increased by about 4.7 times compared to commercial PVDF-based TENG. This could be attributed to the increase of the dielectric constant and hydrophobic property of the PVDF film after the surface polarization enhancement process. Furthermore, the PSPE-TENG-driven sensor can simultaneously monitor both the physical and chemical parameters of the streamflow with high sensitivity and minimum error detection, which proves that the PSPE-TENG has enormous potential applications in self-powered streamflow sensing.

Obtaining Greatly Improved Dielectric Constant in BaTiO3-Epoxy Composites with Low Ceramic Volume Fraction by Enhancing the Connectivity of Ceramic Phase

Ceramic-polymer dielectric composites show promising potential as embedded capacitors, whereas it is a great challenge to obtain a high dielectric constant (ε_r) at a low ceramic volume fraction (V_c). This work demonstrates a strategy for overcoming this challange. By employing a high sintering temperature (T_s) and introducing porogen, BaTiO₃ ceramics with both great connectivity and high porosity are obtained, and the composites with improved ε_r at a low V_c are prepared after curing the epoxy monomer, which is infiltrated into the porous ceramic bodies. For the composite with a T_s of 1300 °C and a V_c of 38.1%, the ε_r is as high as 466.8 at 1 kHz, which is improved by about nine times compared to the 0-3 counterpart with a higher V_c of 60.8%. Furthermore, the composite exhibits low dielectric loss and good frequency and temperature stability of ε_r, indicating the great potential for practical applications. Finite element simulation shows that the enhanced connectivity of BaTiO₃ increases the electric field intensity in high-ε_r BaTiO₃ dramatically and therefore plays a key role in the dielectric response of the composite. This work not only sheds light on the high-ε_r ceramic-polymer composites but also deepens the understanding on the relationship between their properties and microstructures.

Quantification of pre and post air plasma defected graphene oxide dispersed polymer blends for high dielectric applications

Polymer nano blends were more in demand for various domestic and industrial applications. In the present investigation, we modified the Polyvinylidene fluoride (PVDF)/Polysulfone (PSF) polymer blends by dispersion of pre...

Preparation and Characterization of Intrinsic Low-κ Polyimide Films

Three fluorinated polyimide (PI-FP, PI-FO and PI-FH) films with low dielectric constants and excellent comprehensive properties were successfully prepared using a polycondensation reaction method by incorporating p-phenylenediamine (PDA), 4-4′-diaminodiphenyl ether (ODA) and 4,4′-(Hexafluoroisopropylidene) bis (p-phenyleneoxy) dianiline (HFPBDA) into 4,4′-(Hexafluoroisopropylidene) diphthalic anhydride (6FDA), respectively. The effects of the diamine monomer structure on optical, dielectric and mechanical properties were investigated. Compared with PDA and ODA, HFPBDA can effectively improve the optical and dielectric properties of PI due to due to its special chain structure. Among the three PI films, PI-FH film presents the best optic transmission (highest transmittance = 90.2%) and highest energy gap (2.69 eV). The dielectric properties of PI-FH film improve the most. The dielectric constant and loss at 10⁴ Hz are reduced to 2.05 and 0.0034 at 10⁴ Hz, respectively, and remain stable up to 250 °C. The mechanical properties decrease in turn for PI-FP, PI-FO and PI-FH films due to the increase in free volume fraction. Nevertheless, PI-FH film still exhibits good mechanical properties with a tensile strength of 88.4 Mpa, a tensile modulus of 2.11 GPa and an elongation at break of 4.1%. The correlation between the dielectric and mechanical properties of PI films and their free volume characteristics is well explained with the help of positron annihilation spectroscopy.

In Vitro Study on the Piezodynamic Therapy with a BaTiO3-Coating Titanium Scaffold under Low-Intensity Pulsed Ultrasound Stimulation

To solve the poor sustainability of electroactive stimulation in clinical therapy, a strategy of combining a piezoelectric BaTiO3-coated Ti6Al4V scaffold and low-intensity pulsed ultrasound (LIPUS) was unveiled and named here as piezodynamic therapy. Thus, cell behavior could be regulated phenomenally by force and electricity simultaneously. First, BaTiO3 was deposited uniformly on the surface of the three-dimensional (3D) printed porous Ti6Al4V scaffold, which endowed the scaffold with excellent force-electricity responsiveness under pulsed ultrasound exposure. The results of live/dead staining, cell scanning electron microscopy, and F-actin staining showed that cells had better viability, better pseudo-foot adhesion, and more muscular actin bundles when they underwent the piezodynamic effect of ultrasound and piezoelectric coating. This piezodynamic therapy activated more mitochondria at the initial stage that intervened in the cell cycle by promoting cells' proliferation and weakened the apoptotic damage. The quantitative real-time polymerase chain reaction data further confirmed that the costimulation of the ultrasound and the piezoelectric scaffolds could trigger adequate current to upregulated the expression of osteogenic-related genes. The continuous electric cues could be generated by the BaTiO3-coated scaffold and intermittent LIPUS stimulation; thereon, more efficient bone healing would be promoted by piezodynamic therapy in future treatment.

Prospects for the Development of High Energy Density Dielectric Capacitors

In this paper, the design of high energy density dielectric capacitors for energy storage in vehicle, industrial, and electric utility applications have been considered in detail. The performance of these devices depends primarily on the dielectric constant and breakdown strength characteristics of the dielectric material used. A review of the literature on composite polymer materials to assess their present dielectric constants and the various approaches being pursued to increase energy density found that there are many papers in which materials having dielectric constants of 20–50 were reported, but only a few showing materials with very high dielectric constants of 500 and greater. The very high dielectric constants were usually achieved with nanoscale metallic or carbon particles embedded in a host polymer and the maximum dielectric constant occurred near the percolation threshold particle loading. In this study, an analytical method to calculate the dielectric constant of composite dielectric polymers with various types of nanoparticles embedded is presented. The method was applied using an Excel spreadsheet to calculate the characteristics of spiral wound battery cells using various composite polymers with embedded particles. The calculated energy densities were strong functions of the size of the particles and thickness of the dielectric layer in the cell. For a 1000 V cell, an energy density of 100–200 Wh/kg was calculated for 3–5 nm particles and 3–5 µ thick dielectric layers. The results of this study indicate that dielectric materials with an effective dielectric constant of 500–1000 are needed to develop dielectric capacitor cells with battery-like energy density. The breakdown strength would be 300–400 V/µ in a reverse sandwich multilayer dielectric arrangement. The leakage current of the cell would be determined from appropriate DC testing. These high energy density dielectric capacitors are very different from electrochemical capacitors that utilize conducting polymers and liquid electrolytes and are constructed much like batteries. The dielectric capacitors have a very high cell voltage and are constructed like conventional ceramic capacitors.

Boosting Performance of Self-Polarized Fully Printed Piezoelectric Nanogenerators via Modulated Strength of Hydrogen Bonding Interactions

Self-polarized piezoelectric devices have attracted significant interest owing to their fabrication processes with low energy consumption. Herein, novel poling-free piezoelectric nanogenerators (PENGs) based on self-polarized polyvinylidene difluoride (PVDF) induced by the incorporation of different surface-modified barium titanate nanoparticles (BTO NPs) were prepared via a fully printing process. To reveal the effect of intermolecular interactions between PVDF and NP surface groups, BTO NPs were modified with hydrophilic polydopamine (PDA) and hydrophobic 1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES) to yield PDA-BTO and PFD-BTO, respectively. This study demonstrates that the stronger hydrogen bonding interactions existed in PFD-BTO/PVDF composite film comparative to the PDA-BTO/PVDF composite film induced the higher β-phase formation (90%), which was evidenced by the XRD, FTIR and DSC results, as well as led to a better dispersion of NPs and improved mechanical properties of composite films. Consequently, PFD-BTO/PVDF-based PENGs without electric poling exhibited a significantly improved output voltage of 5.9 V and power density of 102 μW cm-3, which was 1.8 and 2.9 times higher than that of PDA-BTO/PVDF-based PENGs, respectively. This study provides a promising approach for advancing the search for high-performance, self-polarized PENGs in next-generation electric and electronic industries.

Influence of Matrix and Surfactant on Piezoelectric and Dielectric Properties of Screen-Printed BaTiO3/PVDF Composites

The aim of this paper was to provide insight into the impact of matrix and surfactants on the rheology, morphology, and dielectric and piezoelectric properties of screen-printed BaTiO3/PVDF composites. Two matrices were compared (PVDF-HFP and PVDF-TrFE), and lead-free BaTiO3 microparticles were added in volume fractions of 30% and 60%. Here, we demonstrated that the presence of surfactants, helping to prevent phase separation, was crucial for achieving a decent screen-printing process. Fourier-transform infrared (FTIR) spectroscopy together with scanning electron microscopy (SEM) showed that the two "fluoro-benzoic acid" surfactants established stable bonds with BaTiO3 and improved the dispersion homogeneity, while the "fluoro-silane" proved to be ineffective due to it evaporating during the functionalization process. PVDF-TrFE composites featured a more homogeneous composite layer, with fewer flaws and lower roughness, as compared with PVDF-HFP composites, and their inks were characterized by a higher viscosity. The samples were polarized in either AC or DC mode, at two different temperatures (25 °C and 80 °C). The 30% BaTiO3 PVDF-TrFE composites with two fluorinated surfactants featured a higher value of permittivity. The choice of the surfactant did not affect the permittivity of the PVDF-HFP composites. Concerning the d33 piezoelectric coefficient, experimental results pointed out that PVDF-TrFE matrices made it possible to obtain higher values, and that the best results were achieved in the absence of surfactants (or by employing the fluoro-silane). For instance, in the composites with 60% BaTiO3 and polarized at 80 °C, a d33 of 7-8 pC/N was measured, which is higher than the values reported in the literature.

Recent developments in the synthesis of chemically modified nanomaterials for use in dielectric and electronics applications

Polymer nanocomposites (PNC) have attracted enormous scientific and technological interest due to their applications in energy storage, electronics, biosensing, drug delivery, cosmetics and packaging industry. Nanomaterials (platelet, fibers, spheroids, whiskers, rods) dispersed in different types of polymer matrices constitute such PNC. The degree of dispersion of the inorganic nanomaterials in the polymer matrix, as well as the structured arrangement of the nanomaterials, are some of the key factors influencing the overall performance of the nanocomposite. To this end, the surface functionalization of the nanomaterials determines its state of dispersion within the polymer matrix. For energy storage and electronics, these nanomaterials are usually chosen for their dielectric properties for enhancing the performance of device applications. Although several reviews on surface modification of nanomaterials have been reported, a review on the surface functionalization of nanomaterials as it pertains to polymer dielectrics is currently lacking. This review summarizes the recent developments in the surface modification of important metal oxide dielectric nanomaterials including Silicon dioxide (SiO₂), titanium dioxide (TiO₂), barium titanate (BaTiO₃), and aluminum oxide (Al₂O₃) by chemical agents such as silanes, phosphonic acids, and dopamine. We report the impact of chemical modification of the nanomaterial on the dielectric performance (dielectric constant, breakdown strength, and energy density) of the nanocomposite. Aside from bringing novice and experts up to speed in the area of polymer dielectric nanocomposites, this review will serve as an intellectual resource in the selection of appropriate chemical agents for functionalizing nanomaterials for use in specific polymer matrix so as to potentially tune the final performance of nanocomposite.

Nonthermal plasma catalysis for toluene decomposition over BaTiO3-based catalysts by Ce doping at A-sites: The role of surface-reactive oxygen species

The insights on the primary surface-reactive oxygen species and their relation with lattice defects is essential for designing catalysts for plasma-catalytic reactions. Herein, a series of Ba_1-xCe_xTiO₃ perovskite catalysts with high specific surface areas (68.6-85.6 m² g^-1) were prepared by a facile in-situ Ce-doping strategy and investigated to catalytically decompose toluene. Combining the catalysts with a nonthermal plasma produced a significant synergy effect. The highest decomposition efficiency (100%), CO_x selectivity (98.1%), CO₂ selectivity (63.9%), and the lowest O₃ production (0 ppm) were obtained when BC₄T (Ce/Ti molar ratio = 4:100) was packed in a coaxial dielectric barrier discharge reactor at a specific input energy of 508.8 J L^-1. The H₂-TPR, temperature-programmed Raman spectra, EPR and OSC results suggested that superoxides (^•O₂^-) were the primary reactive oxygen species and were reversibly generated on the perovskite surface. Molecular O₂ was adsorbed and activated at the active sites (Ti³⁺-V_O) via an electron transfer process to form ^•O₂^-. Surface-adsorbed ^•O₂^- had a greater effect on the heterogeneous surface plasma reactions than the dielectric constant, and enhanced the toluene decomposition and intermediate oxidation. A possible reaction path of toluene decomposition was also proposed.

Mortise-tenon joint structured hydrophobic surface-functionalized barium titanate/polyvinylidene fluoride nanocomposites for printed self-powered wearable sensors

Self-powered wearable sensors exhibiting high sensitivity and flexibility have attracted widespread interest in the field of wearable electronics. Herein, a 3D printing technique was employed to fabricate a fully printed, flexible self-powered sensor with high piezoelectric performance. This printing technique is based on the hydrophobic surface-functionalized barium titanate (FD-BTO)/polyvinylidene fluoride (PVDF) composite film. To strengthen the interface bond between BTO and PVDF, the BTO nanoparticles were surface functionalized using hydrophobic 1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES). As a result, there was an increase in the content of the β-phase in the PFDTES modified BTO (FD-BTO) nanoparticle composite film. The 3D-printed self-powered sensor based on the optimum FD-BTO/PVDF composite film exhibited excellent sensitivity (61.6 mV kPa-1) with a piezoelectric coefficient (d33) of 69.1 pC/N, which is two-fold higher than that of the unfunctionalized BTO/PVDF counterpart. Additionally, the power sensor displayed excellent mechanical durability in the 20 000 cyclic force tests. In practice, the printed devices were used as a sports wearable device to monitor and analyze athlete motion, and a self-powered printed sensor array (5 × 5), which could effectively detect the pattern image of the external pressure input. The 3D-printed self-powered sensor demonstrated herein can contribute significantly to the applications and the development of printed electronic wearable devices.

Significantly Improved Dielectric Performance of Poly(1-butene)-Based Composite Films via Filling Polydopamine Modified Ba(Zr0.2Ti0.8)O3-Coated Multiwalled Carbon Nanotubes Nanoparticles

The low dielectric constant of the nonpolar polymer poly(1-butene) (PB-1) limits its application as a diaphragm element in energy storage capacitors. In this work, Ba(Zr_0.2Ti_0.8)O₃-coated multiwalled carbon nanotubes (BZT@MWCNTs) were first prepared by using the sol-gel hydrothermal method and then modified with polydopamine (PDA) via noncovalent polymerization. Finally, PB-1 matrix composite films filled with PDA-modified BZT@MWCNTs nanoparticles were fabricated through a solution-casting method. Results indicated that the PDA-modified BZT@MWCNTs had good dispersion and binding force in the PB-1 matrix. These characteristics improved the dielectric and energy storage performances of the films. Specifically, the PDA-modified 10 vol% BZT@ 0.5 vol% MWCNTs/PB-1 composite film exhibited the best dielectric performance. At 1 kHz, the dielectric constant of this film was 25.43, which was 12.7 times that of pure PB-1 films. Moreover, its dielectric loss was 0.0077. Furthermore, under the weak electric field of 210 MV·m^-1, the highest energy density of the PDA-modified 10 vol% BZT@ 0.5 vol% MWCNTs/PB-1 composite film was 4.57 J·cm^-3, which was over 3.5 times that of PB-1 film (≈1.3 J·cm^-3 at 388 MV·m^-1).

Hydroxylated BiFeO3 as efficient fillers in poly(vinylidene fluoride) for flexible dielectric, ferroelectric, energy storage and mechanical energy harvesting application

Here we report the effect of surface hydroxylation of BiFeO3 fillers on the dielectric, ferroelectric, energy storage and mechanical energy harvesting performance of poly(vinylidene fluoride). Surface hydroxylation helped to improve the interfacial interaction between the filler and PVDF matrix by introducing a strong hydrogen bonding between the -OH group of the hydroxylated BiFeO3 filler surface and the -CF2 dipole of PVDF in place of electrostatic interfacial interaction between non-hydroxylated BiFeO3 and the -CH2 dipole of PVDF. The amount of polar phase increased to around 91% for a 7 wt% hydroxylated BiFeO3 loaded PVDF film (7BFOH) by this new type of interfacial interaction. The dielectric, ferroelectric, energy storage and mechanical energy harvesting performance of the PVDF based composite films also improved by the above said technique. Upon repeated human finger tapping, the 7BFOH film delivered ∼18 V output peak to peak open circuit ac voltage (VOC). After rectification, the VOC of the 7BFOH film was able to charge a 10 μF capacitor up to ∼3 V which was able to light up some LEDs (connected in parallel) together instantaneously, which proved the real life applicability of the composite films in low power consuming self-powered electronic devices.

Nano-ZnO decorated ZnSnO3 as efficient fillers in PVDF matrixes: toward simultaneous enhancement of energy storage density and efficiency and improved energy harvesting activity

Here, we report the effect of ZnO decoration on ZnSnO3 fillers on the dielectric property, energy storage behaviour and mechanical energy harvesting performance of PVDF matrixes. More enhanced dielectric constant and reduction in dielectric loss were achieved in PVDF-ZnO@ZnSnO3 (PVDF-ZNZS) films than in PVDF-ZnSnO3 (PVDF-ZS) films for the same concentration of filler loading. Similarly, PVDF-ZNZS films showed simultaneous enhancement in electrical energy storage density and storage efficiency compared to PVDF-ZS composites. As all the constituent materials (PVDF, ZnSnO3 and ZnO) were piezoelectric, the resulting composite film showed improved piezoelectric energy harvesting performance too. After rectification, the output ac voltage was used to charge a 10 μF capacitor up to ∼5 V dc which was further used to light up some LEDs. Furthermore, in order to exhibit improved sensitive output, a hybrid piezo-tribo nanogenerator was fabricated which was demonstrated as a motion sensor, a weight sensor and a human body movement sensor as part of a real life application.

Flexible piezoelectric energy harvester with an ultrahigh transduction coefficient by the interconnected skeleton design strategy

Based on the strong demand for self-powered wearable electronic devices, flexible piezoelectric energy harvesters (FPEHs) have recently attracted much attention. A polymer-based piezocomposite is the core of an FPEH and its transduction coefficient (d₃₃×g₃₃) is directly related to the material's power generation capacity. Unfortunately, the traditional 0-3 type design method generally causes a weak stress transfer and poor dispersion of the filler in the polymer matrix, making it difficult to obtain a high d₃₃×g₃₃. In this work, a unique interconnected skeleton design strategy has been proposed to overcome these shortcomings. By using the freeze-casting method, an ice-templated 2-2 type composite material has been constructed with the popular piezoelectric relaxor 0.2Pb(Zn_1/3Nb_2/3)O₃-0.8Pb(Zr_1/2Ti_1/2)O₃ (PZN-PZT) as the filler and PDMS as the polymer matrix. Both the theoretical simulation and the experimental results revealed a remarkable enhancement in the stress transfer ability and piezoelectric response. In particular, the 2-2 type piezocomposite has an ultrahigh transduction coefficient of 58 213 × 10^-15 m² N^-1, which is significantly better than those of previously reported composite materials, and even textured piezoceramics. This work provides a promising paradigm for the development of high-performance FPEH materials.

Flexible Piezoelectric Energy Harvester with Extremely High Power Generation Capability by Sandwich Structure Design Strategy

In order to achieve a high-performance flexible piezoelectric energy harvester (FPEH), a unique sandwich structure, that is, a PVDF film filled with FeTiNbO₆ (FTN) semiconductor particles as an intermediate layer and a pure PVDF film as an upper and lower barrier layer, has been designed, and the corresponding PVDF-FTN/PVDFx-PVDF (P-FTNx-P) compact composite has been prepared by hot-pressing technology. The special sandwich structure combined with the introduction of FTN particles is beneficial to enhance the interfacial polarization and the content of the electroactive phase in PVDF. Together with the maximum piezoelectric voltage coefficient and the moderate Young's modulus, the P-FTN15%-P FPEH exhibited the optimal energy-harvesting performance with a high power density of 110 μW/cm³ and a large charge density of 75 μC/m² in cantilever mode. The outstanding design in this work is expected to provide a new way for the development of high-performance FPEH materials.

Flexible and printable dielectric polymer composite with tunable permittivity and thermal stability

Lightweight and printable polymer dielectrics are ubiquitous in flexible hybrid electronics, exhibiting high breakdown strength and mechanical reliability. However, their advanced electronic applications are limited due to their relatively low permittivity, compared to their ceramic counterparts. Here, we report flexible all organic percolative nanocomposites that contain in situ grown conductive polymer networks and dielectric polymer matrix, in which their dielectric properties can be designed and guided from the percolation theory. High dielectric constant of all organic percolative nanocomposites is shown over a broad frequency range under intensive bending cycles, while their thermal stability is attributed to thermally conductive 2D montmorillonite nanosheets. The printable polymer composites with high dielectric performance and thermal stability will find broader interest in flexible hybrid electronics and radio frequency devices.

Sandwich-structured poly(vinylidene fluoride-hexafluoropropylene) composite film containing a boron nitride nanosheet interlayer

High performance dielectric polymer materials are a key point for energy storage capacitors, especially film capacitors. In this paper, a sandwich-structured polymer film is constructed to achieve high energy density and high efficiency. High dielectric materials of poly(vinylidene fluoride-hexafluoropropylene) (P(VDF-HFP)) doped with barium titanate (BaTiO₃) are used as the outer layer to achieve a high dielectric constant, and a boron nitride nanosheet (BNNS) layer is inserted between P(VDF-HFP)/BaTiO₃ to obtain a high breakdown field strength of composite films. The results indicate that when the doping amount of the BaTiO₃ nanoparticles reaches 10 wt% and the mass fraction of the BNNS layer is 0.75 wt%, a significant improvement of energy storage performance is obtained. The energy storage density of the P(VDF-HFP)/BaTiO₃/BNNSs composite film can reach 8.37 J cm⁻³, which is higher than 6.65 J cm⁻³ of the pure P(VDF-HFP) film. Compared with the P(VDF-HFP) film doped with BaTiO₃, significant improvement of the breakdown field strength (about 148.5%) is achieved and the energy storage density increases 235% accordingly, resulting from the inserted BNNSs layer blocking the growth of electrical branches and suppressing leakage current. This novel sandwich-structured film shows promising future applications for high performance dielectric capacitors.

A novel composite material formed by adding high dielectric inorganic ceramic particles and BNNSs interlayer into a sandwich-structured film.

High dielectric thin films based on barium titanate and cellulose nanofibrils

A series of composite films based on tetragonal barium titanate (BTO) and cellulose nanofibrils (CNF) with high dielectric constant are prepared using a casting method in aqueous solution. No organic solvent is involved during the preparation, which demonstrates the environmental friendliness of the novel material. With less than 30 wt% of filler loading, the excellent distribution of BTO nanoparticles within the CNF matrix is revealed by the FE-SEM images. The dielectric constant of the CNF/BTO (30 wt%) composite film reaches up to 188.03, which is about seven times higher than that of pure CNF (25.24), while the loss tangent only rises slightly from 0.70 to 1.21 (at 1 kHz). The thin films kept their dielectric properties on an acceptable level after repeatedly twisting or rolling 10 times. The improvement of thermal stability is observed with the presence of BTO. The outstanding dielectric properties of the CNF/BTO composite film indicates its great potential to be utilized in energy storage applications.

The high dielectric thin films based on cellulose fibrils and tetragonal barium titanate exhibit excellent dielectric properties, flexibility and durability.

Interface design for high energy density polymer nanocomposites

This review provides a detailed overview on the latest developments in the design and control of the interface in polymer based composite dielectrics for energy storage applications. The methods employed for interface design in composite systems are described for a variety of filler types and morphologies, along with novel approaches employed to build hierarchical interfaces for multi-scale control of properties. Efforts to achieve a close control of interfacial properties and geometry are then described, which includes the creation of either flexible or rigid polymer interfaces, the use of liquid crystals and developing ceramic and carbon-based interfaces with tailored electrical properties. The impact of the variety of interface structures on composite polarization and energy storage capability are described, along with an overview of existing models to understand the polarization mechanisms and quantitatively assess the potential benefits of different structures for energy storage. The applications and properties of such interface-controlled materials are then explored, along with an overview of existing challenges and practical limitations. Finally, a summary and future perspectives are provided to highlight future directions of research in this growing and important area.