Effect of preset torque setting on torque/force generation, shaping ability and surface changes of nickel titanium rotary instrument in different root canal curvature locations: An ex vivo study

The aim of this study was to evaluate how preset torque settings influence the torque, vertical force, and root canal-centering ability of ProGlider and ProTaper NEXT nickel-titanium rotary instruments in canals with different curvature locations. Based on micro-computed tomography, mesial roots of human mandibular molars (25°-40° curvature) were allocated to the apical curvature (apical 1-5 mm) or the middle curvature (apical 5-9 mm) groups, and mandibular incisors (curvature <5°) to the straight canal group. Each group was subjected to automated instrumentation and torque/force measurement with the preset torque of 1, 2.5, or 5 N•cm. Canal-centering ratios were determined with micro-computed tomography. Instrument fracture occurred only in the 2.5 and 5 N•cm groups in curved canals. The preset torque setting and curvature location did not influence canal shaping ability.

Phase transformation behavior and mechanical properties of HyFlex EDM nickel-titanium endodontic rotary instrument: Evaluation at body temperature

Background/purpose

Temperature-dependent phase compositional changes influence the mechanical properties of heat-treated nickel-titanium (NiTi) rotary instruments. This study evaluated the phase composition, bending properties, and cyclic fatigue resistance of HyFlex EDM NiTi rotary instruments against differently heat-treated and non-heat-treated NiTi instruments at body temperature (BT).

Materials and methods

HyFlex EDM OneFile (EDM) instruments, heat-treated HyFlex CM (CM) and Twisted File (TF) instruments, and non-heat-treated K3 instruments (size #25/.08) were subjected to differential scanning calorimetry, and the martensitic, R-phase, and reverse transformation starting and finishing temperatures were determined. A cantilever bending test and a cyclic fatigue test were conducted at BT (37 °C ± 1.0 °C), and the bending load and number of cycles to failure (NCF) were recorded. Statistical analysis was performed using Kruskal-Wallis and Mann-Whitney U tests (α = 0.05).

Results

TF and K3 had reverse transformation finishing temperatures lower than BT, while those for EDM and CM were higher than BT. The bending loads at a 0.5 mm deflection were in the order of EDM < TF < CM < K3 (P < 0.05), and those at a 2.0 mm deflection were EDM < CM and TF < K3 (P < 0.05). EDM had the highest NCF among the four instruments (P < 0.05).

Conclusion

The EDM instrument had a reverse transformation finishing temperature higher than BT indicating its martensite/R-phase composition at BT. The EDM instrument had superior flexibility and greater resistance to cyclic fatigue than the CM, TF, and K3 instruments at BT.

Phase transformation and mechanical properties of heat-treated nickel-titanium rotary endodontic instruments at room and body temperatures

BACKGROUND

The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated nickel-titanium (NiTi) rotary instruments with the same tip diameter and taper at room (RT; 25 ± 1 °C) and body (BT; 37 ± 1 °C) temperatures.

METHODS

Five heat-treated NiTi rotary instruments, HyFlex EDM (EDM), HyFlex CM (CM), Vortex Blue (VB), RE file CT (RE) and JIZAI, and a non-heat-treated NiTi rotary instrument (Mtwo) with a size 40, 0.04 taper were investigated. Temperature-dependent phase transformation was examined with differential scanning calorimetry (DSC). The bending loads of the instruments at RT and BT were evaluated using a cantilever-bending test. Cyclic fatigue resistance at RT and BT was measured using a dynamic test, during which the instruments were rotated in combination with a 2-mm back-and-forth motion in an artificial curved canal, and the number of cycles to failure (NCF) was determined. The results were analyzed using two-way repeated measures analysis of variance, a simple main effect test, and the Bonferroni test (α = 0.05).

RESULTS

DSC results indicated that EDM and Mtwo were primarily composed of martensite/R-phase and austenite, respectively, while the other heat-treated instruments were composed of a mix of martensite/R-phase and austenite at the tested temperatures. Regardless of the temperature setting, the bending loads of heat-treated instruments were significantly lower than those of Mtwo (p < 0.05). EDM showed the lowest bending loads and highest NCF at both temperatures (p < 0.05). CM, VB, and JIZAI showed significantly higher bending loads at BT than at RT (p < 0.05). The NCF of all the heat-treated instruments, except VB, was lower at BT than at RT (p < 0.05). At BT, the NCF of CM, VB, RE, and JIZAI were not significantly higher than that of Mtwo (p > 0.05).

CONCLUSIONS

Heat-treated NiTi instruments exhibited lower bending loads and higher NCF values than Mtwo. However, this tendency was less pronounced at BT than at RT, especially in the NCF values of instruments with a mixture of martensite/R-phase and austenite phases at the tested temperatures.

Dynamic torque and screw-in force of four different glide path instruments assessed in simulated single- and double-curved canals: An in vitro study

Background/purpose

The glide path instruments are the introductory instruments into the canals; thus, they should be durable enough to withstand torsional stress/screw-in force. This study aimed to investigate the torque and screw-in force of TruNatomy Glider (TN), ProGLIDER (PG), Hyflex EDM (EDM) and Dent Craft RE (RE) glide path instruments in single- and double-curved canals.

Materials and methods

Each instrument brand was divided into two groups (n = 7 each) according to the canal configuration. Torque and screw-in force were recorded during automated instrumentation of simulated resin canals with XSmart IQ cordless motor after the canal patency was checked with a #10 K-file. The values were statistically analyzed using the Kolmogorov-Smirnov test followed by the Kruskal Wallis test and the Mann-Whitney U test with Bonferroni correction (α = 0.05).

Results

TN produced significantly higher torque than RE in single-curved canals and PG in double-curved canals (P < 0.05). EDM yielded significantly higher screw-in force than TN and RE in single-curved canals (P < 0.05), but there was no significant difference in double-curved canals (P > 0.05). A significant effect of different canal configurations was only detected for screw-in force in EDM (P < 0.05).

Conclusion

TN in single-curved canals and RE in double-curved canals yielded higher torque values, while EDM exhibited greater screw-in force in both canal configurations. No effect of different canal configurations was detected for torque, but a significant impact was detected for screw-in force in EDM.

A case of breast milk-acquired cytomegalovirus infection in an extremely low birth weight infant

INTRODUCTION

Although breast milk is considered the optimal nutrition for infants, it is also the primary cause of postnatal cytomegalovirus (CMV) infection. Preterm infants with postnatal CMV infections are susceptible to a variety of life-threatening conditions.

CASE SUMMARY

Twin male infants were delivered via emergency caesarian section at 27 weeks' gestation secondary to maternal complete uterine rupture. The Apgar scores at 1 and 5 min were 1 and 1 for the older twin (Twin A) and 0 and 3 for the younger twin (Twin B). Their birth weights were 1203 g (+ 0.65SD) and 495 g (- 3.79SD) respectively. On day 41, laboratory blood test results for Twin B showed a moderate elevation in C-reactive protein (CRP), thrombocytopenia. CMV quantitative polymerase chain reaction (qPCR) tests in Twin B's urine and blood as well as in the mother's breast milk were positive, but stored, dried umbilical cord CMV qPCR tests were negative. Twin B was diagnosed with a postnatal CMV infection secondary to infected breast milk and ganciclovir was commenced on day 52. Treatment was switched to valganciclovir at 74 days of age, but a negative CMV-DNA level in the blood was not achieved. Postnatal CMV infection in this infant led to an exacerbation of pre-existing bronchopulmonary dysplasia (BPD) and he demised at 182 days of age.

CONCLUSION

Postnatal cytomegalovirus infections may lead to exacerbations of BPD. Early use of raw breast milk in preterm infants should be done with careful consideration of this potential complication.

Effect of different axial speed patterns on cyclic fatigue resistance of rotary nickel-titanium instruments

BACKGROUND

To evaluate the effect of pecking motions with faster upward speed on the dynamic cyclic fatigue resistance of nickel-titanium rotary instruments with different metallurgy.

METHODS

Forty each of ProTaper Universal F3 (PTU) and ProTaper Gold F3 (PTG) instruments (size #30/.09) were equally divided into four groups. The test was performed using an 18-mm-long stainless steel artificial canal with a 5-mm radius of curvature, a 45° canal curvature and a 2-mm canal diameter. A downward speed of 100 mm/min was employed, while the upward speed was set at 100, 150, 200 or 300 mm/min. Time to failure (Tf), number of cycles to failure (Nf) and number of pecking motions to failure (Np) were recorded. Statistical analysis was performed using Kruskal Wallis and Mann-Whitney U tests for Tf, Nf, and Np (α = 0.05).

RESULTS

The 100/300 mm/min group showed significantly higher Np values than the 100/100 mm/min group (p < 0.05), whereas there were no significant differences in Tf and Nf among the tested speed groups (p < 0.05) in either PTU or PTG. PTG exhibited significantly higher Tf, Nf, and Np than PTU (p < 0.05).

CONCLUSIONS

Under the tested conditions, the fastest upward speed group showed significantly higher cyclic fatigue resistance, as demonstrated by larger Np, than the same speed group. PTG had significantly higher cyclic fatigue resistance than PTU in all groups.

Mechanical Properties and Root Canal Shaping Ability of a Nickel-Titanium Rotary System for Minimally Invasive Endodontic Treatment: A Comparative In Vitro Study

Selection of an appropriate nickel−titanium (NiTi) rotary system is important for minimally invasive endodontic treatment, which aims to preserve as much root canal dentin as possible. This study aimed to evaluate selected mechanical properties and the root canal shaping ability of TruNatomy (TRN), a NiTi rotary system designed for minimally invasive endodontic shaping, in comparison with existing instruments: HyFlex EDM (HEDM), ProTaper Next (PTN), and WaveOne Gold (WOG). Load values measured with a cantilever bending test were ranked as TRN < HEDM < WOG < PTN (p < 0.05). A dynamic cyclic fatigue test revealed that the number of cycles to fracture was ranked as HEDM > WOG > TRN > PTN (p < 0.05). Torque and vertical force generated during instrumentation of J-shaped artificial resin canals were measured using an automated instrumentation device connected to a torque and vertical force measuring system; TRN exhibited smaller torque and vertical force values in most comparisons with the other instruments. The canal centering ratio for TRN was smaller than or comparable to that for the other instruments except for WOG at the apex level. Under the present experimental conditions, TRN showed higher flexibility and lower torque and vertical force values than the other instruments.

Effect of Rotational Modes on Torque/Force Generation and Canal Centering Ability during Rotary Root Canal Instrumentation with Differently Heat-Treated Nickel-Titanium Instruments

This study aimed to evaluate how various rotational modes influence the torque/force production and shaping ability of ProTaper Universal (PTU; non-heat-treated) and ProTaper Gold (PTG; heat-treated) nickel−titanium instruments. J-shaped resin canals were instrumented with PTU or PTG using an automated instrumentation device operated with reciprocating rotation [150° clockwise and 30° counterclockwise (R150/30) or 240° clockwise and 120° counterclockwise (R240/120)], optimum torque reverse motion (OTR), or continuous rotation (CR) (n = 10 each). Maximum force and torque were recorded, and canal centering ratios were calculated. Statistical analysis was performed with two-way ANOVA and a Bonferroni test (α = 0.05). The results were considered with reference to previous studies on the microstructure of the instruments. The upward force generated by R240/120 and OTR was smaller than that generated by R150/30 and CR in PTG (p < 0.05). The clockwise torque produced by OTR was lower than that produced by R150/30 in PTU and R240/120 and CR in PTG (p < 0.05). R240/120 and OTR induced less canal deviation compared to CR in PTU at 0 mm from the apex (p < 0.05). In conclusion, R240/120 and OTR reduced the screw-in force in PTG and improved the canal centering ability in PTU, which may be associated with the heat treatment-induced microstructural difference of the two instruments.

Effect of kinematics on the torque/force generation, surface characteristics, and shaping ability of a nickel titanium rotary glide path instrument: an ex-vivo study

AIM

To evaluate the effect of various rotational motions on the torque/force generation, surface wear, and shaping ability of the ProGlider glide path instrument (Dentsply Sirona).

METHODOLOGY

Mesiobuccal and mesiolingual canals of mandibular molars were selected based on the canal volume, length, angle of curvature (25°-40°), and radius of curvature (4-8 mm) after micro-computed tomographic scanning. The samples were randomly assigned to four groups (n = 13, each) according to movement kinematics [continuous rotation (CR; 300 rpm), optimum torque reverse motion (OTR; 180° forward and 90° reverse when torque > 0.4 N·cm), time-dependent reciprocal motion (TmR; 180° forward and 90° reverse), and optimum glide path motion (OGP; a combination of 90° forward, 90° reverse, 90° forward, and 120° reverse)]. Instrumentation was performed with an automated root canal instrument and torque/force analysing device. Maximum torque/force values, canal volume changes, and canal-centring ratios at 1, 3, 5, and 7 mm were evaluated. Surface defects (pits, grooves, microcracks, blunt cutting edges, and disruption of cutting edges) and spiral distortion on the ProGlider instrument were scored at the tip and 5 mm short of the tip before and after five consecutive uses with scanning electron microscopy. The Kruskal-Wallis test followed by Dunn's post-test with Bonferroni correction and Wilcoxon signed-rank test were used to analyse the data (α = 0.05).

RESULTS

OGP generated significantly less clockwise torque and greater upward force than other groups (P < 0.05). OGP resulted in significantly fewer surface defects than CR (P < 0.05). In OGP and CR, the tip exhibited more surface defects than 5 mm short of the tip (P < 0.05). CR resulted in greater volume changes than OGP and TmR (P < 0.05) and greater centring ratios (i.e., more deviation) than OGP at 1 mm and OTR at 3 mm (P < 0.05).

CONCLUSIONS

Under laboratory conditions using the ProGlider instrument, OGP generated significantly less clockwise torque and greater upward force than the other rotatory motions. OGP generated fewer superficial defects than CR, and the three modes of reciprocal rotation better maintained the apical curvature of root canals than CR with the ProGlider instrument.

Verification of the Usefulness of an Assessment and Risk Control Sheet that Promotes Management of Cancer Drug Therapy

Background: Proper management of adverse events is crucial for the safe and effective implementation of anticancer drug treatment. Showa University Hospital uses our interview sheet (assessment and risk control [ARC] sheet) for the accurate evaluation of adverse events. On the day of anticancer drug treatment, a nurse conducts a face-to-face interview. As a feature of the ARC sheet, by separately describing the symptoms the day before treatment and the day of treatment and sharing the information on the medical record, it is possible to clearly determine the status of adverse events. In this study, we hypothesized that the usefulness and points for improvement of the ARC sheet would be clarified by using and evaluating a patient questionnaire.

Methods: This study included 174 patients (144 at Showa University Hospital (Hatanodai Hospital) and 30 at Showa University Koto Toyosu Hospital (Toyosu Hospital) who underwent pre-examination interviews by nurses and received cancer chemotherapy at the outpatient center of Hatanodai and Toyosu Hospital. In the questionnaire survey, the ARC sheet’s content and quality, respondents’ satisfaction, structural strengths, and points for improvement were evaluated on a five-point scale.

Results: The patient questionnaire received responses from 160 participants, including the ARC sheet use group (132 people) and the non-use group (28 people). Unlike the ARC sheet non-use group, the ARC sheet use group recognized that the sheet was useful to understand the adverse events of aphthous ulcers (p = 0.017) and dysgeusia (p = 0.006). In the satisfaction survey questionnaire, there was a high sense of security in the pre-examination interviews by nurses using the ARC sheet.

Conclusions: The ARC sheet is considered an effective tool for comprehensively evaluating adverse events. Pre-examination interviews by nurses using ARC sheets accurately determined the adverse events experienced by patients with anxiety and tension due to confrontation with physicians.

Influence of rotational speed on torque/force generation and shaping ability during root canal instrumentation of extracted teeth with continuous rotation and optimum torque reverse motion

AIM

To evaluate how different rotational speeds affect the torque/force generation and shaping ability of rotary root canal instrumentation using JIZAI (MANI, Utsunomiya, Japan) nickel-titanium instruments in continuous rotation and optimum torque reverse (OTR) motion.

METHODOLOGY

Mesial root canals of extracted mandibular molars were instrumented up to size 25, 0.04 taper using JIZAI instruments, and anatomically matched canals were selected based on geometric features of the canal [canal volume (mm³ ), surface area (mm² ), length, 15°-20° curvature and radius of curvature (4-8 mm)] after micro-computed tomographic scanning. An automated root canal instrumentation and torque/force analysing device was programmed to permit a simulated pecking motion (2 s downward and 1 s upward at 50 mm min^-1 ). The selected canals were prepared with size 25, 0.06 taper JIZAI instruments using continuous rotation or OTR motion and further subdivided according to the rotational speed (300 or 500 rpm, n = 10 each). Real-time clockwise/counterclockwise torque and downward/upward force were recorded using a custom-made torque/force analysing device. Then, the registered pre- and post-operative micro-computed tomographic datasets were examined to evaluate the canal volume changes and centring ratios at 1, 3, 5 and 7 mm from the apical foramen. Data were analysed using two-way analysis of variance or the Kruskal-Wallis test and Mann-Whitney U test with Bonferroni correction (α = 5%).

RESULTS

Maximum upward force and clockwise torque were significantly smaller in 500 rpm groups than in 300 rpm groups (P < .05); however, no significant difference was found between continuous rotation and OTR motion (P > .05). OTR motion developed higher maximum counterclockwise torque than continuous rotation (P < .05). Maximum downward force, canal volume changes and centring ratios were not significantly different among all groups (P > .05). There was no file fracture in any of the groups.

CONCLUSIONS

Under laboratory conditions using JIZAI instruments, a rotational speed of 500 rpm generated significantly lower maximum screw-in forces and torque values than rotational speed of 300 rpm. Continuous rotation and OTR motion performed similarly in shaping the canals.

Comparative evaluation of mechanical properties and shaping performance of heat-treated nickel titanium rotary instruments used in the single-length technique

This study aimed to evaluate the mechanical properties of contemporary heat-treated nickel-titanium (NiTi) rotary instruments used in the single-length technique [ProTaper Next (PTN), HyFlex EDM (EDM), and JIZAI (JZ)]. Bending loads, cyclic fatigue resistance, torque/force values and canal-centering ratios were evaluated for the three instruments and a non-heat-treated experimental NiTi instrument with the same geometry as JZ (nJZ). EDM and JZ exhibited significantly lower bending load and more cycles to failure compared with nJZ and PTN (p<0.05). PTN and JZ exhibited significantly better centering ability than nJZ and EDM (p<0.05). JZ and nJZ generated significantly smaller upward force and maximum torque than PTN and EDM (p<0.05). Under the present experimental condition, JZ exhibited flexibility and cyclic fatigue resistance comparable to EDM, better maintained the canal curvature than the other instruments, and generated smaller torque and screw-in force than PTN and EDM.

Impact of the Coronavirus Disease 2019 Outbreak on Activity and Exercise Levels among Older Patients

OBJECTIVES

This study aimed to clarify the impact of the coronavirus disease 2019 outbreak on the levels of activity among older patients with frailty or underlying diseases. A total of 175 patients (79.0±7.0 years) undergoing outpatient or home-based rehabilitation, stratified into groups, based on frailty status. The percentage of patients who went out at least once a week decreased after the outbreak from 91% to 87%, from 65% to 46%, and from 47% to 36% in the non-frail, frail, and nursing care requirement groups, respectively. The proportion of older patients participating in exercise during the outbreak was 75%, 51%, and 41% in the non-frail, frail, and nursing care requirement groups, respectively. The proportion of older patients participating in voluntary exercise after instruction was lowest in the frail group (35%). Older patients with frailty are susceptible to the negative effects of refraining from physical activity and require careful management.

Comparison of Torque, Screw-in Force, and Shaping Ability of Glide Path Instruments in Continuous Rotation and Optimum Glide Path Motion

INTRODUCTION

This study aimed to analyze torque/force generation and transportation in double-curved canals instrumented with 3 types of glide path files using optimum glide path (OGP) motion in comparison with continuous rotation.

METHODS

Sixty simulated double-curved canals were prepared with #10/0.05 or #15/0.03 HyFlex EDM Glidepath files (Coltene/Whaledent, Altstätten, Switzerland) or a #13/0.04 prototype MANI Glidepath file (Tochigi, Japan) using OGP motion or continuous rotation (n = 10 each). Canals were sequentially prepared to 20 mm and 22 mm (full working length) using automated root canal instrumentation and a torque/force analyzing device. Transportation was calculated at 1-9 mm from the apex. Data were compared using 2-way analysis of variance followed by a post hoc simple main effect test with Bonferroni correction and a Kruskal-Wallis test (α = 5%).

RESULTS

All #10/0.05 instruments fractured. In the 22-mm preparation, the OGP motion resulted in lower clockwise torque and screw-in force than did continuous rotation (P < .05). In the 20-mm preparation, #15/0.03 instruments recorded a lower screw-in force for OGP motion than for continuous rotation (P < .05). Comparing the 2 preparation phases, OGP motion generated no significant differences; however, continuous rotation developed higher clockwise torque and screw-in force in the 22-mm preparation than in the 20-mm preparation (P < .05). There was no significant difference among the tested groups for transportation values.

CONCLUSIONS

Compared with continuous rotation, OGP motion generated less screw-in force, lower clockwise torque, and similar transportation. The #15/0.03 HyFlex EDM instrument and the #13/0.04 prototype MANI instrument performed similarly well.

Cyclic Fatigue Resistance of Rotary and Reciprocating Nickel-Titanium Instruments Subjected to Static and Dynamic Tests

INTRODUCTION

This study compared the static and dynamic cyclic fatigue resistance of contemporary nickel-titanium instruments with different kinematic, metallurgic, and design features to establish whether the fatigue-reducing effect of the pecking motion differs among different nickel-titanium instruments.

METHODS

ProTaper Gold (PTG), Hyflex EDM (EDM), Reciproc Blue (RPB), and WaveOne Gold (WOG) files were divided into 2 groups of 10 for the static and dynamic cyclic fatigue resistance tests. A stainless steel artificial canal with 1.5-mm inner diameter, 60° angulation, and 3-mm radius of curvature was used. In the dynamic cyclic fatigue resistance test, speeds were set at 100 and 200 mm/min for the descending and ascending motion, respectively. The number of cycles to fracture (NCF) was calculated, the fractured lengths were recorded, and fractographic analysis of the fractured surfaces was carried out by scanning electron microscopy. Data were analyzed statistically with the Kruskal-Wallis test with Bonferroni correction (alpha = 0.05).

RESULTS

The RPB and EDM showed significantly higher NCF in the static and dynamic cyclic fatigue resistance tests (P < .05). The dynamic cyclic fatigue resistance test showed significantly higher NCF than the static cyclic fatigue resistance test in the PTG and EDM (P < .05). There was no significant difference between the RPB and WOG (P > .05).

CONCLUSIONS

In the experimental condition where the ascending speed was higher than the descending speed, the dynamic cyclic fatigue resistance was significantly higher than the static cyclic fatigue resistance in continuous rotary instruments, but not in reciprocating instruments.

Functional Analysis of PTH1R Variants Found in Primary Failure of Eruption

Although many variants of the parathyroid hormone 1 receptor (PTH1R) gene are known to be associated with primary failure of eruption (PFE), the mechanisms underlying the link remains poorly understood. We here performed functional analyses of PTH1R variants reported in PFE patients-namely, 356C>T (P119L), 395C>T (P132L), 439C>T (R147C), and 1148G>A (R383Q)-using HeLa cells with a lentiviral vector-mediated genetic modification. Two particular variants, P119L and P132L, had severe reduction in a level of N-linked glycosylation when compared with wild-type PTH1R, whereas the other 2 showed modest alteration. PTH1R having P119L or P132L showed marked decrease in the affinity to PTH_1-34, which likely led to severely impaired cAMP accumulation upon stimulation in cells expressing these mutants, highlighting the importance of these 2 amino acid residues for ligand-mediated proper functioning of PTH1R. To further gain insights into PTH1R functions, we established the induced pluripotent stem cell (iPSC) lines from a patient with PFE and the heterozygous P132L mutation. When differentiated into osteoblastic-lineage cells, PFE-iPSCs showed no abnormality in mineralization. The mRNA expression of RUNX2, SP7, and BGLAP, the osteoblastic differentiation-related genes, and that of PTH1R were augmented in both PFE-iPSC-derived cells and control iPSC-derived cells in the presence of bone morphogenetic protein 2. Also, active vitamin D₃ induced the expression of RANKL, a major key factor for osteoclastogenesis, equally in osteoblastic cells derived from control and PFE-iPSCs. In sharp contrast, exposure to PTH_1-34 resulted in no induction of RANKL mRNA expression in the cells expressing P132L variant PTH1R, consistent with the idea that a type of heterozygous PTH1R gene mutation would spoil PTH-dependent response in osteoblasts. Collectively, this study demonstrates a link between PFE-associated genetic alteration and causative functional impairment of PTH1R, as well as a utility of iPSC-based disease modeling for future elucidation of pathogenesis in genetic disorders, including PFE.

Assessment of mechanical properties of WaveOne Gold Primary reciprocating instruments

This study aimed to evaluate cyclic fatigue resistance and bending properties and torque/force generation of WaveOne Gold (WOG) Primary in comparison with WaveOne (WO) Primary and Reciproc (RE) R25. A cyclic fatigue test revealed that the WOG Primary took significantly longer time to fracture compared with the WO Primary (p<0.05). The WOG Primary had the smallest load values at a deflection of 0.5 and 2 mm (p<0.05), as measured with a cantilever bending test. Torque/force measurement demonstrated that maximum upward force and maximum counterclockwise torque values in the WOG Primary were significantly lower than those in the RE R25 (p<0.05). Under the present experimental condition, the WOG Primary showed a higher cyclic fatigue resistance compared with the WO Primary, a higher flexibility compared with the WO Primary and RE R25, and generated a significantly lower maximum torque compared with the RE R25.

8-Nitro-cGMP is a promoter of osteoclast differentiation induced by RANKL

Osteoclasts are multinucleated giant cells differentiated from monocyte-macrophage-lineage cells under stimulation of receptor activator of nuclear factor κ-B (RANK) ligand (RANKL) produced by osteoblasts and osteocytes. Although it has been reported that nitric oxide (NO) and reactive oxygen species (ROS) are involved in this process, the mechanism by which these labile molecules promote osteoclast differentiation are not fully understood. In this study, we investigated the formation and function of 8-nitro-cGMP, a downstream molecule of NO and ROS, in the process of osteoclast differentiation in vitro. 8-Nitro-cGMP was detected in mouse bone marrow macrophages and osteoclasts differentiated from macrophages in the presence of RANKL. Inhibition of NO synthase suppressed the formation of 8-nitro-cGMP as well as RANKL-induced osteoclast differentiation from macrophages. On the other hand, RANKL-induced osteoclast differentiation was promoted by addition of 8-nitro-cGMP to the cultures. In addition, 8-nitro-cGMP enhanced the mRNA expression of RANK, the receptor for RANKL. However, 8-bromo-cGMP, a membrane-permeable derivative of cGMP, did not have an effect on either RANKL-induced osteoclast differentiation or expression of the RANK gene. These results suggest that 8-nitro-cGMP is a novel positive regulator of osteoclast differentiation, which might help to explain the roles of NO and ROS in osteoclast differentiation.

Gene Expression Profiling of Mouse Condylar Cartilage during Mastication by Means of Laser Microdissection and cDNA Array

Little is known about the mechanisms of mandibular condylar growth. In this study, gene expression in the mandibular condylar cartilage of young post-natal mice was monitored by means of a cDNA microarray, real-time PCR, and laser microdissection before and after the initiation of mastication (newborn, 7 days, 21 days, initiation of mastication, and 35 days). Insulin-like growth factor-1 (IGF-I), transforming-growth-factor-beta-2 (TGFbeta2), and aggrecan mRNAs were clearly expressed at 21 days, while the expression of osteopontin mRNAs was most clear at 35 days. Parathyroid-hormone-related protein (PTHrP), Indian-hedgehog (Ihh), and insulin-like growth factor-2 (IGF-2) mRNAs were clearly expressed during lactation (newborn and 7 days). Heat-shock-protein 84 (HSP-84) and heat-shock-protein 86 (HSP-86) were clearly expressed at 35 days. These results revealed that gene expression changed during mandibular condylar cartilage growth, and that, interestingly, these changes coincided with the initiation of mastication.

The skeletal maturation status estimated by statistical shape analysis: axial images of Japanese cervical vertebra

OBJECTIVES

To evaluate axial cervical vertebral (ACV) shape quantitatively and to build a prediction model for skeletal maturation level using statistical shape analysis for Japanese individuals.

METHODS

The sample included 24 female and 19 male patients with hand-wrist radiographs and CBCT images. Through generalized Procrustes analysis and principal components (PCs) analysis, the meaningful PCs were extracted from each ACV shape and analysed for the estimation regression model.

RESULTS

Each ACV shape had meaningful PCs, except for the second axial cervical vertebra. Based on these models, the smallest prediction intervals (PIs) were from the combination of the shape space PCs, age and gender. Overall, the PIs of the male group were smaller than those of the female group. There was no significant correlation between centroid size as a size factor and skeletal maturation level.

CONCLUSIONS

Our findings suggest that the ACV maturation method, which was applied by statistical shape analysis, could confirm information about skeletal maturation in Japanese individuals as an available quantifier of skeletal maturation and could be as useful a quantitative method as the skeletal maturation index.

Differences in the developmental origins of the periosteum may influence bone healing

BACKGROUND AND OBJECTIVE

The jaw bone, unlike most other bones, is derived from neural crest stem cells, so we hypothesized that it may have different characteristics to bones from other parts of the body, especially in the nature of its periosteum. The periosteum exhibits osteogenic potential and has received considerable attention as a grafting material for the repair of bone and joint defects.

MATERIAL AND METHODS

Gene expression profiles of jaw bone and periosteum were evaluated by DNA microarray and real-time polymerase chain reaction. Furthermore, we perforated an area 2 mm in diameter on mouse frontal and parietal bones. Bone regeneration of these calvarial defects was evaluated using microcomputed tomography and histological analysis.

RESULTS

The DNA microarray data revealed close homology between the gene expression profiles within the ilium and femur. The gene expression of Wnt-1, SOX10, nestin, and musashi-1 were significantly higher in the jaw bone than in other locations. Microcomputed tomography and histological analysis revealed that the jaw bone had superior bone regenerative abilities than other bones.

CONCLUSION

Jaw bone periosteum exhibits a unique gene expression profile that is associated with neural crest cells and has a positive influence on bone regeneration when used as a graft material to repair bone defects. A full investigation of the biological and mechanical properties of jaw bone as an alternative graft material for jaw reconstructive surgery is recommended.

Is the prognostic impact of tumor location in patients with surgically resected esophageal squamous cell carcinoma affected by surgical approach?

AIM

The aim of the present study was to clarify differences in node metastasis mode and clinical outcomes based on tumor location in patients with esophageal squamous cell carcinoma (ESCC).

PATIENTS AND METHODS

Participants comprised 228 patients with ESCC who underwent radical esophagectomy without preoperative supplement therapies. Lymph nodes were harvested from three fields: the neck, thorax, and abdomen. Patients were divided into three groups depending on tumor location [upper esophagus (UE), middle esophagus, or lower esophagus (LE)] and analyzed clinicopathologically.

RESULTS

The LE group showed significantly more progressive ESCC in terms of tumor invasion (p = 0.025), node metastasis (p = 0.0071), and TNM stage (p = 0.0043). The LE group revealed a tendency to metastasize to extrathoracic (especially abdominal) nodes (p = 0.0008). Recurrent laryngeal node metastasis was increased in the UE group (p = 0.016). However, no prognostic differences were detected between groups according to tumor location. Likewise, subgroup analyses by surgical approach (open thoracotomy vs. thoracoscopy) and cancer stage (stage I/II, III, and IV) did not reveal any significant prognostic impact of tumor location.

CONCLUSION

Lymphatic spread varied by tumor location, but no prognostic impact of tumor location could be detected in patients with ESCC in spite of surgical approach or cancer stage.

Three-dimensional evaluation of upper airway in patients with different anteroposterior skeletal patterns

OBJECTIVES

To investigate variability in the upper airway of subjects with different anteroposterior skeletal patterns by evaluating the volume and the most constricted cross-sectional area of the pharyngeal airway and defining correlations between the different variables.

MATERIAL AND METHODS

The study sample consisted of 60 patients (29 boys, 31 girls) divided into three groups: Class I (1 ≤ ANB ≤ 3), Class II (ANB>3), and Class III (ANB<1), to evaluate how the jaw relationship affects the airway volume and the most constricted cross-sectional area (Min-CSA). Differences between groups were determined using the Tukey-Kramer test. Correlations between variables were tested using Pearson's correlation coefficient.

RESULTS

The volume and the Min-CSA of the pharyngeal airway (PA) were significantly related to anteroposterior skeletal patterns (p < 0.05). The nasopharyngeal airway (NA) volume of Class I and Class III subjects was significantly larger than that of Class II subjects (p < 0.05). The Min-CSA and the length of PA were significantly related to the volume of PA (p < 0.05). The site and the size of the Min-CSA varied among the three groups.

CONCLUSIONS

The volume and the most constricted cross-sectional area of the airway varied with different anteroposterior skeletal patterns. The NA volume of Class I and Class III subjects was significantly larger than that of patients with a Class II skeletal pattern.

Switching to an L/N-type calcium channel blocker shows renoprotective effects in patients with chronic kidney disease: the Kyoto Cilnidipine Study

OBJECTIVE

This open-label, randomized controlled trial investigated the effects of cilnidipine, an L/N-type calcium channel blocker (CCB), in patients with chronic kidney disease (CKD).

METHODS

Sixty patients with CKD and well-controlled hypertension being treated with a renin- angiotensin system (RAS) inhibitor and an L-type CCB (L-CCB) were randomly assigned either to switch from the L-CCB to cilnidipine after a 4-week observation period or to continue with L-CCB treatment. Blood pressure, heart rate and renal function were monitored for 12 months. Data were available for analysis from 50 patients: 24 from the cilnidipine group and 26 from the L-CCB group.

RESULTS

Blood pressure was well controlled in both groups. After 12 months, proteinuria and heart rate were significantly decreased in the cilnidipine group, but proteinuria increased and heart rate remained unchanged in the L-CCB group. There was a significant positive correlation between the percentage changes in proteinuria and heart rate.

CONCLUSIONS

Cilnidipine has antihypertensive effects equivalent to those of L-CCBs. In patients with CKD, proteinuria can be decreased by switching from an L-CCB to cilnidipine, thereby improving renal function.

Medical emergency education using a robot patient in a dental setting

INTRODUCTION

In an ageing society, the frequency of medical emergencies in a dental setting appears to be increasing because of a growing number of medically compromised patients. However, we currently have no dental-specific simulation environment with advanced reproducibility for medical emergencies. Therefore, we used the robot patient in objective structured clinical examinations (OSCEs) for testing student competence in emergency management. This study aimed to evaluate student responses to medical emergencies in the dental setting.

MATERIAL AND METHODS

We used 98 fifth-grade dental students at Showa University as subjects and implemented the OSCE task entitled 'Management of medical emergency using a robot patient'. Candidates were asked to manage an emergency situation immediately after local anaesthesia, with one robot patient configured to develop vasovagal syncope and the other to experience adrenaline hypersensitivity. A questionnaire on the educational value of the robot patient was completed after the examination.

RESULTS

Thirty-two per cent of students could not accurately count her pulse because of an inappropriate method. Moreover, 78% could not correctly attach either the tonometer or pulse oximetry to the patient. Accurate diagnoses were given by only 22% of students, with vasovagal syncope diagnosed by 33% and adrenaline hypersensitivity by 8%. From a questionnaire, 78% of students recognised the usefulness of the robot patient in medical emergency training.

CONCLUSION

We found that student responses to the emergency situation were poor. The robot patient is useful in dental education for medical emergency training and assessment not only for situation management but also for differential diagnosis.

Serum leptin levels negatively correlate with trabecular bone mineral density in high-fat diet-induced obesity mice

OBJECTIVES

This study evaluated the influence of diet-induced obesity on bone tissue quantity and quality in the proximal tibiae of growing mice and also examined the relationships between the serum total cholesterol, leptin, and adiponectin levels and trabecular and cortical bone mineral parameters.

METHODS

Six-week-old male C57BL/6J mice were divided into two groups; one received a control diet, and the other received a high-fat-diet. After treatment for 4, 8, or 12 weeks, the bone quantity and quality were analyzed using peripheral quantitative computed tomography (pQCT), micro-computed tomography and histomorphometry.

RESULTS

In the early stages, trabecular bone density decreased with an increase in the number of adipocytes and the deterioration of trabeculae. In contrast, although cortical bone formation was slower in obese mice compared with control mice, bone formation on the periosteal surface increased with age. Serum leptin levels were correlated with trabecular, but not cortical bone density, whereas neither the adiponectin nor total cholesterol level was correlated with bone mass in mice with diet-induced obesity.

CONCLUSIONS

We conclude that bone loss at these two sites is differentially regulated in mice. Furthermore, we demonstrate that serum leptin may be a useful indicator of risk for osteoporosis associated with diet-induced obesity.

Introduction of a robot patient into dental education

In recent years, with the increasing social awareness of safety in medical practice, improving clinical skills has become very important, especially for recently graduated dentists. Traditionally, mannequins have been used for clinical skill training, but a mannequin is quite different from a real patient because they have no autonomous movement or conversational ability. This indicates that pre-clinical simulation education is inadequate. We have, therefore, developed a robot patient that can reproduce an authentic clinical situation for dental clinical training. The robot patient, designed as a full-body model with a height of 157 cm, has eight degrees of freedom in the head and the ability to perform various autonomous movements. Moreover, saliva secretion and conversation with the trainee can be reproduced. We have introduced the robot patient into an objective structured clinical examination targeted at fifth-grade students in our dental school to evaluate their skills in cavity preparation, whilst considering the safety of the treatment. As a result, many of the students were able to deal appropriately with a patient's unexpected movement. Moreover, results of a questionnaire survey showed that almost all the students recognised the educational value of the robot patient especially for 'risk management', and they preferred the robot patient to traditional mannequins. Practical application of the robot patient in dental clinical education was evaluated through the experiences of the fifth-grade students, which showed the effectiveness of the robot patient in the dental field.

Mineral trioxide aggregate inhibits osteoclastic bone resorption

Mineral trioxide aggregate (MTA), a commonly used endodontic repair material, is useful for both basic and clinical research, and the effect of MTA on osteoblast differentiation has been well-defined. However, the effects of MTA on osteoclastic bone resorption are not fully understood. Hence, the aim of this study is to examine the effect of MTA solution in the regulation of osteoclast bone-resorbing activity using osteoclasts formed in co-cultures of primary osteoblasts and bone marrow cells. MTA solution dose-dependently reduced the total area of pits formed by osteoclasts. The reduction of resorption induced by 20% MTA treatment was due to inhibition of osteoclastic bone-resorbing activity and had no effect on osteoclast number. A 20% MTA solution disrupted actin ring formation, a marker of osteoclastic bone resorption, by reducing phosphorylation and kinase activity of c-Src, and mRNA expressions of cathepsin K and mmp-9. A high concentration of MTA solution (50%) induced apoptosis of osteoclasts by increasing the expression of Bim, a member of the BH3-only (Bcl-2 homology) family of pro-apoptotic proteins. Taken together, our results suggest that MTA is a useful retrofilling material for several clinical situations because it both stimulates osteoblast differentiation and inhibits bone resorption.

Orthodontic treatment of a unilateral impacted mandibular canine and first premolar: a case report

BACKGROUND

Few dentists have seen an impacted mandibular canine and first premolar, and there is little information in the literature on the treatment of this rare condition.

CASE REPORT

A 13-year-old Japanese male with an impacted mandibular right canine and first premolar was treated orthodontically. We discuss both the surgical and orthodontic options and present the successful orthodontic correction of a unilaterally impacted mandibular canine and first premolar.

Practical human abdominal fat imaging utilizing electrical impedance tomography

The fundamental cause of metabolic syndrome is thought to be abdominal obesity. Accurate diagnosis of abdominal obesity can be done by an x-ray computed tomography (CT) scan. But CT is expensive, bulky and entails the risks involved with radiation. To overcome such disadvantages, we attempted to develop a measuring device that could apply electrical impedance tomography to abdominal fat imaging. The device has 32 electrodes that can be attached to a subject's abdomen by a pneumatic mechanism. That way, electrode position data can be acquired simultaneously. An applied alternating current of 1.0 mArms was used at a frequency of 500 kHz. Sensed voltage data were carefully filtered to remove noise and processed to satisfy the reciprocal theorem. The image reconstruction software was developed concurrently, applying standard finite element methods and the Marquardt method to solve the mathematical inverse problem. The results of preliminary experiments showed that abdominal subcutaneous fat and the muscle surrounding the viscera could be imaged in humans. While our imaging of visceral fat was not of sufficient quality, it was suggested that we will be able to develop a safe and practical abdominal fat scanner through future improvements.

Analysis of bone volume using computer simulation system for secondary bone graft in alveolar cleft

The purpose of this study was to measure the bone volume necessary for secondary bone grafting in the alveolar cleft using surgical simulation software based on three-dimensional computed tomography (CT) scan data, to compare this measurement with the actual volume of the bone graft, and to evaluate consistency. The subjects were 13 patients with cleft lip and palate who underwent CT using a cone-beam CT unit (CB-CT) 1 month before surgery, followed by bone grafting with particulate cancellous bone and marrow (PCBM) to close the cleft. The bone volume necessary for grafting was measured based on the CB-CT scan data. Correlation analysis, a test of the population mean between two samples, and Wilcoxon's signed rank test were conducted between these measurements and the actual bone volume (PCBM volume) used for grafting. SPSS was used for statistical analysis, and the level of significance was set below the 5% level. The results showed a significant correlation, with no significant differences between the two in all tests. These results suggest that measuring and preoperatively calculating the bone volume necessary for bone grafting with surgical simulation software using CB-CT scan data is beneficial.

Comparison of cone beam computed tomography imaging with physical measures

OBJECTIVES

The goal of this study was to determine the accuracy of measuring linear distances between landmarks commonly used in orthodontic analysis on a human skull using two cone beam CT (CBCT) systems.

METHODS

Measurements of length were taken using volumetric data from two CBCT systems and were compared with physical measures using a calliper applied to one human adult skull. Landmarks were identified with chromium steel balls embedded at 32 cranial and 33 mandibular landmarks and the linear measures were taken with a digital calliper. The skull was then scanned with two different CBCT systems: the NewTom QR DVT 9000 (Aperio Inc, Sarasota, FL) and the Hitachi MercuRay (Hitachi Medico Technology, Tokyo, Japan). CT data including the landmark point data were threshold segmented using CyberMed's CB Works software (CB Works 1.0, CyberMed Inc., Seoul, Korea). The resulting segmentations were exported from CB Works as VRML (WRL) files to Amira software (Amira 3.1, Mercury Computer Systems GmbH, Berlin, Germany).

RESULTS

The error was small compared with the gold standard of the physical calliper measures for both the NewTom (0.07+/-0.41 mm) and CB MercuRay (0.00+/-0.22 mm) generated data. Absolute error to the gold standard was slightly positive, indicating minor compression relative to the calliper measurement. The error was slightly smaller in the CB MercuRay than in the NewTom, probably related to a broader greyscale range for describing beam attenuation in 12-bit vs 8-bit data.

CONCLUSIONS

The volumetric data rendered with both CBCT systems provided highly accurate data compared with the gold standard of physical measures directly from the skulls, with less than 1% relative error.

Orthodontic treatment for an unerupted and severely rotated maxillary central incisor. A case report

BACKGROUND

Many reports have indicated the treatment for permanent teeth with disturbed eruption due to the presence of supernumerary teeth. However, successful treatment for an unerupted maxillary incisor with severe rotation and another maxillary incisor with disturbed eruption by a supernumerary tooth is quite rare.

CASE REPORT

We treated a 7-year-old Japanese male with an unerupted and severely rotated maxillary right incisor, along with a maxillary left incisor due to interference with eruption by an inverted supernumerary tooth. Orthodontic treatment using surgical exposure, traction and guidance of the rotated right incisor, and maxillary expansion following extraction of the supernumerary tooth were performed.

FOLLOW-UP

At 27 months following extraction of the supernumerary tooth, and comprehensive orthodontic treatment led the malposititioned central incisors to a functional position and stable occlusion.

Increased expression of aquaporin-3 in the epidermis of DHCR24 knockout mice

BACKGROUND

The DHCR24 (3beta-hydroxysterol-Delta24 reductase) gene encodes an enzyme catalysing conversion of desmosterol to cholesterol. Desmosterolosis is an autosomal recessive disease due to mutation in the DHCR24 gene, with low cholesterol and high desmosterol levels. To understand the pathophysiology of this disease, we utilized DHCR24 knockout mice and reported that DHCR24-/- mice die soon after birth. Their skin was less wrinkled, shiny, and revealed features of lethal restrictive dermopathy associated with severe defects in epidermal maturation and barrier function.

OBJECTIVES

Markedly increased transepidermal water loss in DHCR24-/- mice led us to examine the role of aquaporin-3 (AQP3), because this is the only water/glycerol transporting channel protein expressed in the epidermis.

METHODS

Expression of AQP3 was studied by Western blot analysis and immunohistochemistry in the epidermis of DHCR24-/- and wild-type newborn mice. Glycerol uptake was determined in the isolated keratinocytes and glycerol content in the epidermis was analysed by an enzymatic method.

RESULTS

In control mice, AQP3 was expressed only in cells of the stratum basale, indicating its expression in immature keratinocytes. In DHCR24-/- mice, AQP3 was expressed throughout the epidermis and colocalized with the immature keratinocytes (keratin 14-positive cells). The increased AQP3 expression in the epidermis of DHCR24-/- mice was mirrored by a significantly higher glycerol uptake and glycerol content. This was associated with an increase in epidermal water content of DHCR24-/- mice.

CONCLUSIONS

This is the first demonstration that elevated AQP3 results in the retention of epidermal water, causing the taut, wrinkle-free skin phenotype of the DHCR24-/- mice.

Study of salivary strontium and silver concentrations in primary school children related to dental caries

To investigate the relationship between the salivary Sr and Ag concentrations and tooth conditions, saliva was collected from 521 primary school children in Kitakyushu. The salivary Sr and Ag levels were determined using an atomic absorption spectrophotometry. The salivary Sr and Ag levels were 7.73 +/- 3.62 and 0.03 +/- 0.15 ng/ml, respectively, in the sound teeth group. No sex differences were noted in either element level, nor were there differences between the lower and upper grade groups. In the caries teeth group, the Sr and Ag levels were significantly higher than those in the sound teeth group. The Sr level was significantly increased by caries experience regardless caries being treated or untreated. In second to third grade children, in whom the fluoride experience rate was high, the Sr level tended to be lower than that in the other grades. The salivary Ag level increased as the number of teeth treated with silver alloy rose. These findings suggested that the salivary Sr level increases because of caries susceptibility, and F inhibits Sr dissolution from the teeth. The salivary Ag level varied depending on the type of dental filling and was dependent on the amount of silver alloy in children treated with low-fusing silver alloy.

Rapid detection of the cariogenic pathogens Streptococcus mutans and Streptococcus sobrinus using loop-mediated isothermal amplification

INTRODUCTION

Streptococcus mutans and Streptococcus sobrinus are associated with the development of dental caries in humans. In this study, we developed a rapid, sensitive method for detecting these major cariogenic pathogens using loop-mediated isothermal amplification (LAMP). The assay procedure is quite simple: the amplification is carried out in a single tube under isothermal conditions at 63 degrees C, and the result can be obtained in less than 1 h.

METHODS

Initially, a set of six primers was designed by targeting S. mutans-specific and S. sobrinus-specific regions, identified using the genomic subtractive hybridization technique. We evaluated the specificities and sensitivities of these assays. Furthermore, we detected and quantified these bacteria in saliva and carious dentin from eight children.

RESULTS

The sensitivities of the S. mutans-specific and S. sobrinus-specific LAMP methods, examined using agarose gel electrophoresis, were each one cell for a 30-min reaction. The detection limits using real-time turbidimetry analysis were 1 to 10(7) cells (3.28 x 10(1) to 3.28 x 10(8) fg S. mutans template DNA) per reaction tube and 1 to 10(5) cells (2.72 x 10(3) to 2.72 x 10(8) fg S. sobrinus template DNA) per reaction tube. Using these assays, we detected and quantified these cariogenic bacteria for evaluation of the LAMP assay for clinical diagnosis.

CONCLUSIONS

Our results suggest that the LAMP-based assay in combination with subtractive hybridization is valuable for preparing species-specific primers for closely related species. Furthermore, the LAMP-based assay will be a useful tool for the rapid and sensitive prediction of dental caries.

[Successful treatment for descending necrotizing mediastinitis; report of a case]

A case of a 55-year-old man with descending necrotizing mediastinitis (DNM) after a tooth removal was reported. Chest computed tomography (CT) showed a fluid collection in the right thorax, in the cervical region and in the mediastinum. The patient underwent cervical drainage and thoracoscopic pleural dissective drainage. The cervical and right anterior thoracic drain was removed on the 6th day and posterior drain was removed on the 8th day after the operation. The patient was discharged on the postoperative day 13, and showed no recurrence.