Hollow CoP/carbon as an efficient catalyst for the peroxymonosulfate activation derived from phytic acid assisted metal-organic framework

The catalyst's composition and rationally designed structure is significantly interlinked with its performance for wastewater remediation. Here, a novel hollow cobalt phosphides/carbon (HCoP/C) as an efficient catalyst for activating peroxymonosulfate (PMS) was prepared. The ZIF-67 was synthesized first, followed by phytic acid (PA) etching and then heat treatment was used to get HCoP/C. The PA was used as an etching agent and a source of phosphorus to prepare HCoP/C. To analyze catalytic performance, another solid cobalt phosphides/carbon (SCoP/C) catalyst was prepared for comparison. In contrast to SCoP/C, the HCoP/C exhibited higher catalytic efficiency when used to activate PMS to degrade Bisphenol A (BPA). The results showed that about 98 % of targeted pollutant BPA was removed from the system in 6 min with a rate constant of 0.78 min-1, which was 4 times higher than the solid structure catalyst. The higher catalytic performance of HCoP/C is attributed to its hollow structure. In the study, other parameters such as BPA concentration, temperature, pH, and different catalyst amount were also tested. Moreover, the electron paramagnetic resonance (EPR) and radical quenching analysis confirmed that sulfate radicals were dominant in the HCoP/C/PMS system.

Morphological and structural characteristics of the elytra reduce impact damage to ladybird beetles

Beetle elytra act as natural protective covers and effectively shield their flexible abdomens and fragile hindwings from damage. The existing studies have attributed this contribution of the elytra to its honeycomb structures. In this combined experimental and theoretical study, we used the seven-spotted ladybird beetle to demonstrate that both biological morphology and the hollow structure of the dome-like elytra combined to reduce damage during falling. The falling ladybird beetles had a high probability (59.52%) of hitting the ground with the costal edge of the elytra. This strategy could assist with converting the translational energy into rotational kinetic energy, resulting in the reduction of the impulse during falling. In addition, the hollow structures on the elytra could further absorb the residual impact energy. In the future, this biological paradigm could be used as a basis for the development of falling/landing techniques for advanced robots.

Photoelectron Migration Boosted by Hollow Double-Shell Dyads Based on Covalent Organic Frameworks for Highly Efficient Photocatalytic Hydrogen Generation

Photocatalytic hydrogen production based on noble metal-free systems is a promising technology for the conversion of solar energy into green hydrogen, it is pivotal and challenging to tailor-make photocatalysts for achieving high photocatalytic efficiency. Herein, we reported a hollow double-shell dyad through uniformly coating covalent organic frameworks (COFs) on the surface of hollow Co9S8. The double shell architecture enhances the scattering and refraction efficiency of incident light, shortens the transmission distance of the photogenerated charge carriers, and exposes more active sites for photocatalytic conversion. The hydrogen evolution rate is as high as 23.15 mmol g-1 h-1, which is significantly enhanced when compared with that of their physical mixture (0.30 mmol g-1 h-1) and Pt-based counterpart (11.84 mmol g-1 h-1). This work provides a rational approach to the construction of noble-metal-free photocatalytic systems based on COFs to enhance hydrogen evolution performance.

Hollow structured CdS@ZnIn2S4 Z-scheme heterojunction for bifunctional photocatalytic hydrogen evolution and selective benzylamine oxidation

Photocatalytic hydrogen evolution (PHE) is frequently constrained by inadequate light utilization and the rapid combination rate of the photogenerated electron-hole pairs. Additionally, conventional PHE processes are often facilitated by the addition of sacrificial reagents to consume photo-induced holes, which makes this approach economically unfavorable. Herein, we designed a spatially separated bifunctional cocatalyst decorated Z-scheme heterojunction of hollow structured CdS (HCdS) @ZnIn2S4 (ZIS), which was prepared by a sacrificial hard template method followed by photo-deposition. Consequently, PdOx@HCdS@ZIS@Pt exhibited efficient PHE (86.38 mmol·g-1·h-1) and benzylamine (BA) oxidation coupling (164.75 mmol·g-1·h-1) with high selectivity (97.34 %). The unique hollow core-shelled morphology and bifunctional cocatalyst loading in this work hold great potential for the design and synthesis of bifunctional Z-scheme photocatalysts.

Recyclable fabrication of hollow N-doped amorphous carbon nanospindles with abundant short-range curved carbon fragments as bifunctional anode for lithium/sodium ion storage

A recyclable hard-template method is proposed to exploit spindle-shaped hollow nitrogen-doped amorphous carbon (h-NAC) with a large number of short-range curved carbon fragments as anodes for lithium/sodium ion batteries (LIBs/SIBs). Besides providing adsorption sites due to the high existence of oxygen-containing functional groups (CO and COOH), the heavily exposed edge regions also provide a favorable storage environment with high adsorption energy for Li+/Na+ due to their short-range curved structure. Importantly, the etching solution of hard templates can be recycled to generate the FeOOH nanospindles as a precursor through a simple chemical titration, which supplies a new idea for the green preparation of hollow materials. The h-NAC electrode is proven to be bifunctional for storing lithium and sodium ions, displaying favorable rate capability (255 mAh g-1 and 106 mAh g-1 at 5 A g-1 for LIBs and SIBs, respectively). After 1000 cycles at 1 A g-1, the reproducible capacities of the LIBs and SIBs kept 496 mAh g-1 and 181 mAh g-1, respectively.

Development of lightweight and high-strength hollow titanium-plated denture material using three-dimensional printing

Owing to its desirable ability to fabricate complex shapes, three-dimensional printing is preferred over casting for manufacturing dentures. Furthermore, titanium is widely used in dental implants and dentures because of its high corrosion resistance, biocompatibility, strength, and low density. In this study, we aimed to develop a new metal denture material from three-dimensional-printed (3DP) to achieve lighter weight and greater strength than those of PMMA dentures. Hollow (3DP-H) structure and solid (3DP-S) structure titanium plate specimens of 0.5, 1.0, and 3.0 mm in thickness were used. Casted Ti, casted Co-Cr, and PMMA plates were fabricated for comparison. Elastic modulus, density, thermal conductivity, hardness, and proof stress of the specimens were measured and plotted on a radar chart to enable multifaceted evaluation. The results indicated that the density of the 3DP-H plates reduced by 28-36% compared with those of 3DP-S and cast Ti plates. The weight of the metal-denture-equivalent section of the 0.5-mm-thick 3DP-H titanium-plated denture reduced to two-thirds that of the 2.0-mm-thick PMMA denture. The proof stress of the 0.5-mm-thick 3DP-H plate increased to about 3 times that of the 2.0-mm-thick PMMA plate. The total value of the 0.5-mm-thick 3DP-H titanium plates was higher than it of the 1.0-mm-thick PMMA plates. This study suggests that it is possible to produce 3DP-H titanium plate dentures exhibiting not only extremely lightweight compared to conventional PMMA dentures but also sufficient strength.

K-N Bridge-Mediated charge separation in hollow g-C3N4 Frameworks: A bifunctional photocatalysts towards efficient H2 and H2O2 production

The development of bifunctional photocatalysts for enhancing hydrogen (H2) and hydrogen peroxide (H2O2) production from water is essential in addressing environmental and energy issues. However, the practical implementation of photocatalytic technology is still constrained by the inadequate separation of photo-generated charge carriers. Herein, potassium (K) atoms are introduced into the interlayers of graphitic carbon nitride (g-C3N4) with a hollow hexagonal structure (K-TCN) and are coordinated with N atoms in adjacent layers. The presence of K-N coordination serves as a layer bridge, facilitating the separation of charge carriers. The hollow hexagonal structure reduces the distance over which photogenerated electrons migrate to the surface, thereby enhancing the reaction kinetics. Consequently, the optimized K-TCN exhibits a dramatically improved photocatalytic H2 (941.6 μmol g-1h-1 with platinum (Pt) as the cocatalyst) and H2O2 (347.6 μmol g-1h-1) generation as compared to hollow g-C3N4 (TCN) and bulk g-C3N4 nanosheet (CN) without K-N bridge under visible light irradiation. The unique design holds promising potential for developing highly efficient bifunctional photocatalysts towards producing renewable fuels and value-added chemicals.

Immobilization enhancement of heavy metals in lightweight aggregate by component regulation of multi-source solid waste

Integrated recycling of solid waste containing heavy metals is a critical environmental challenge. In this study, a green solution to reduce heavy metal leaching from solid waste is demonstrated by combining contaminated soil, industrial sludge and lithium slag in pairs to produce lightweight aggregates (LWAs). The physical properties and heavy metal leaching behavior of LWA samples were systematically investigated and characterized. The results showed that industrial sludge reduced the density and water absorption of LWA, while the high content of lithium slag was detrimental to the physical properties. LWA containing 80% contaminated soil and 20% lithium slag had the lowest particle density of 1.47 g/cm3 due to the hollow structure caused by the low viscosity and violent generation of SO2. LWAs with lithium slag leached excessive Cu and Cr relatively, while heavy metals were immobilized well in LWAs with contaminated soil and industrial sludge as the main components. Because the flux components of industrial sludge could enhance the encapsulation of heavy metals by glass phase. In addition, the co-immobilization of multiple heavy metals was observed in the spinel phase. This study provides an efficient and safe method for the synergistic recycling of solid waste.

Rational design of hollow Ti2Nb10O29 nanospheres towards High-Performance pseudocapacitive Lithium-Ion storage

Ti2Nb10O29, as one of the most promising anode materials for lithium-ion batteries (LIBs), possesses excellent structural stability during lithiation/delithiation cycling and higher theoretical capacity. However, Ti2Nb10O29 faces some challenges, such as insufficient ion diffusion coefficient and poor electronic conductivity. To overcome these problems, this study investigates the effect of applying nanostructure engineering on Ti2Nb10O29 and the lithium storage behaviors. We successfully synthesized hollow Ti2Nb10O29 nanospheres (h-TNO NSs) via solvothermal method using phenolic resin nanospheres as the template. The effects of using a template or not and the annealing atmospheres on the microstructures of the as-prepared Ti2Nb10O29 are investigated. Different nanostructures (porous Ti2Nb10O29 nanoaggregates (p-TNO NAs) without a template and core-shelled Ti2Nb10O29@C nanospheres (cs-TNO@C NSs)) were formed through annealing in Ar. When examined as anodes for LIBs, the h-TNO NSs electrode with hollow spherical structure displayed a better lithium storage performance. Compared to its counterparts, p-TNO NAs and cs-TNO@C NSs, h-TNO NSs electrode exhibited a higher reversible capacity of 282.5 mAh g-1 at 1C, capacity retention of 79.5% (i.e., 224.6 mAh g-1) after 200 cycles, and a higher rate capacity of 173.1 mAh g-1 at 10C after 600 cycles. The excellent electrochemical performance of h-TNO NSs is attributed to the novel structure. The hollow nanospheres with cavities and thin shells not only exposed more active sites and improved ion diffusion, but also buffered the volume variation upon cycling and facilitated electrolyte penetration. This consequently enhanced the lithium storage performance of the electrode and its high pseudocapacitive contribution (90% at 1.0 mV s-1).

Mesalazine hollow suppositories based on 3D printing for treatment of ulcerative colitis

Mesalazine (MSZ) suppositories are a first-line medication for the localized treatment of ulcerative colitis (UC). However, the frequent defecation of patients with UC influences the retention of the suppository in the rectum and multiple doses have to be applied. Here, a mesalazine hollow suppository (MHS) is developed using three-dimensional (3D) printing. The MHS is composed of an inner supporting spring and an outer MSZ-loaded curved hollow shell. Springs were prepared using fused deposition modeling (FDM) 3D printing with thermoplastic urethane filaments, followed by splitting. The optimal parameters, including elasticity, filament diameter, spring inner diameter, and filament distance, were screened. The shell was prepared by FDM 3D printing utilizing MSZ, polyvinyl alcohol, and polyethylene glycol, which were assembled with springs to obtain FDM 3D-printed MHS (F-MHS); if 3D-printed metal molding was used in preparing shell, mold-formed MHS (M-MHS) was obtained. The F-MHS exhibited faster MSZ release than the M-MHS; therefore, the molding method is preferable. The inserted M-MHS was retained in the rat rectum for 5 h without affecting defecation. M-MHS alleviated tissue damage of UC rats and reduced inflammation with low levels of myeloperoxidase and proinflammatory cytokines. Personalized MHS is a promising medication for the localized treatment of UC.

Indium selenide/silver phosphate hollow microsphere S-scheme heterojunctions for photocatalytic hydrogen production with simultaneous degradation of tetracycline

Designing heterojunction photocatalysts with strong interfacial interactions is an effective way to reduce the recombination of photogenerated charge carriers. Here, silver phosphate (Ag₃PO₄) nanoparticles are coupled with hollow flower-like indium selenide (In₂Se₃) microspheres by a facile Ostwald ripening and in-situ growth method, resulting in the construction of In₂Se₃/Ag₃PO₄ hollow microsphere step-scheme (S-scheme) heterojunction with a large contact interface. The flower-like In₂Se₃ with hollow and porous structure provides a large specific surface area and numerous active sites for photocatalytic reactions to take place. The photocatalytic activity was tested by measuring the hydrogen evolution from antibiotic wastewater, and the H₂ evolution rate of In₂Se₃/Ag₃PO₄ reached 4206.4 µmol g^-1h^-1 under visible light, which is approximately 2.8 times greater than that of In₂Se₃. In addition, the amount of tetracycline (TC) degradation when it was used as a sacrificial agent is about 54.4% after 1 h. On the one hand, Se-P chemical bonds act as electron transfer channels in the S-scheme heterojunctions, which can facilitate the migration and separation of photogenerated charge carriers. On the other hand, the S-scheme heterojunctions can retain the useful holes and electrons with higher redox capacities, which is very favorable for the generation of more •OH radicals and the photocatalytic activity is greatly enhanced. This work provides an alternative design approach for photocatalysts toward hydrogen evolution in antibiotic wastewater.

Synthesis of hollow CuFe2O4 microspheres decorated nitrogen-doped graphene hybrid composites for broadband and efficient electromagnetic absorption

The development of graphene-based electromagnetic wave (EMW) absorbers with broad bandwidth, strong absorption and low filling ratio remains a big challenge. In this work, hollow copper ferrite microspheres decorated nitrogen-doped reduced graphene oxide (NRGO/hollow CuFe₂O₄) hybrid composites were prepared by a two-step route of solvothermal reaction and hydrothermal synthesis. Results of microscopic morphology analysis showed that the NRGO/hollow CuFe₂O₄ hybrid composites had a special entanglement structure between hollow CuFe₂O₄ microspheres and wrinkled NRGO. Moreover, the EMW absorption properties of as-prepared hybrid composites could be regulated by changing the additive amounts of hollow CuFe₂O₄. It was worth noting that when the additive amount of hollow CuFe₂O₄ was 15.0 mg, the attained hybrid composites showed the optimal EMW absorption performance. The minimum reflection loss reached up to -34.18 dB at a thin matching thickness of 1.98 mm and a low filling ratio of 20.0 wt%, and the corresponding effective absorption bandwidth was as large as 5.92 GHz, covering almost the whole Ku band. Furthermore, when the matching thickness was increased to 3.02 mm, the EMW absorption capacity was significantly enhanced, and the optimal reflection loss value of -58.45 dB was achieved. In addition, the possible EMW absorption mechanisms were proposed. Therefore, the structural design and composition regulation strategy presented in this work would provide a great reference value for the preparation of broadband and efficient graphene-based EMW absorbing materials.

Novel design constructed In2S3@SnO2 hollow heterojunctions by insufficiently etched MOFs as framework for photoelectrochemical bioanalysis

Compared to sufficiently etched MOFs materials, insufficiently etched MOFs materials tend to display unsatisfactory performance due to their immature structure and have been eliminated from scientific research. Herein, this work reported a novel In₂S₃@SnO₂ heterojunction (In₂S₃@SnO₂-HSHT) materials, which were stably synthesized in high temperature aqueous environment and equipped extraordinary photoelectrochemical (PEC) properties, fabricated by a succinct hydrothermal synthesis method using insufficiently etched MIL-68 as a self-sacrificing template. Compared with the control groups and In₂S₃@SnO₂ heterojunctions with collapse morphology synthesized by sufficiently etched MIL-68 in high temperature aqueous environment, In₂S₃@SnO₂-HSHT synthesized from insufficiently etched MIL-68 as a template had a massively enhanced light-harvesting capability and generated more photoinduced charge carriers due to its well-preserved hollow structure. Therefore, based on outstanding PEC performance of In₂S₃@SnO₂-HSHT, the established PEC label-free signal-off immunosensor to detect CYFRA 21-1, revealing vivid selectivity, stability, and reproducibility. This novel strategy adopted the insufficient chemical etching method neglected by the mainstream chemical etching approaches, which solved the challenge that the stability of the sufficient etched MOFs with hollow structure cannot be maintained under the subsequent high temperature aqueous reaction conditions, and was further applied to the design of hollow heterojunction materials for photoelectrochemical fields.

Boosted visible-light-driven degradation over stable ternary heterojunction as a plasmonic photocatalyst: Mechanism exploration, pathway and toxicity evaluation

The incorporation of plasmonic metals into semiconductors forming heterojunction photocatalysts is a promising route to enhance the photocatalytic performance in visible light. In this work, we reported the visible-light-driven one-dimensional (1D) nanostick silver/silver sulfide (Ag/Ag₂S) photocatalyst combining with two-dimensional (2D) nanosheet reduced graphene oxide intersected by hollow structure (h-RGO) was prepared via a feasible approach at room temperature. The density of Ag depositing on the surface of Ag₂S was easily tuned by the concentration of sodium borohydride and the silicon dioxide nanospheres were employed as templates in the preparation of h-RGO by the layer-by-layer (LBL) assembly. The ternary plasmonic Ag/Ag₂S/h-RGO photocatalysts exhibited better photocatalytic performance for degradation of naphthalene (95.95%) and 1-naphthol (98.65%) under visible light than the pure Ag₂S, composite Ag/Ag₂S and composite Ag/Ag₂S/RGO. Localized surface plasmon resonance of Ag, heterojunction formed between Ag/Ag₂S and RGO and the unique characteristics of h-RGO, which included higher specific surface areas, more efficient reflections of light and more active sites than RGO for boosting separation efficiency of charge carriers, were all responsible for such enhancement. By combining the characterization results with various computations, the mechanism, potential degradation pathways and the toxicity of the generated intermediates for photodegradation were examined. In addition to offering profound insight into the expansion of effective plasmonic photocatalysts with novel structures, the current study is beneficial to ease the environmental crisis to a certain extent.

Constructing hollow ZIF-8/CDs@MIPs fluorescent sensor from Osmanthus leaves to specifically recognize bovine hemoglobin

To develop non-toxic, highly efficient and selective fluorescence sensors was a significance research. In this work, a novel hollow fluorescence sensor was designed with biomass carbon dots (CDs), ZIF-8 and molecularly imprinted polymers (MIPs) via aqueous polymerization. The results demonstrated such unique structure fluorescence sensor exhibited fast response time, excellent stability and highly selectively towards bovine hemoglobin (BHb). Even in a complex environment, the hollow fluorescence sensor (H-ZIF-8/CDs@MIPs) still has a good recognition effect on BHb. Under an optimized condition, the hollow fluorescence sensor was quenched linearly with BHb concentration in the range of 0.058-4.5 μM with the detection limit of 15.6 nM. In addition, a possible quenching mechanism of hollow fluorescence towards BHb was confirmed resonance energy transfer (FRET). In the actual application process, the hollow fluorescence sensor showed a better detection performance towards BHb with the recoveries ranged of 98.6-101.1 %. This work provided a strategy to design green and unique hollow fluorescence sensor for practical application.

Hollow Ni/NiO/C composite derived from metal-organic frameworks as a high-efficiency electrocatalyst for the hydrogen evolution reaction

Metal-organic frameworks (MOFs) constitute a class of crystalline porous materials employed in storage and energy conversion applications. MOFs possess characteristics that render them ideal in the preparation of electrocatalysts, and exhibit excellent performance for the hydrogen evolution reaction (HER). Herein, H-Ni/NiO/C catalysts were synthesized from a Ni-based MOF hollow structure via a two-step process involving carbonization and oxidation. Interestingly, the performance of the H-Ni/NiO/C catalyst was superior to those of H-Ni/C, H-NiO/C, and NH-Ni/NiO/C catalysts for the HER. Notably, H-Ni/NiO/C exhibited the best electrocatalytic activity for the HER, with a low overpotential of 87 mV for 10 mA cm^-2 and a Tafel slope of 91.7 mV dec^-1. The high performance is ascribed to the synergistic effect of the metal/metal oxide and hollow architecture, which is favorable for breaking the H-OH bond, forming hydrogen atoms, and enabling charge transport. These results indicate that the employed approach is promising for fabricating cost-effective catalysts for hydrogen production in alkaline media.

Low quantity of Pt loaded onto CeCoOx nanoboxes: Surface-rich reactive oxygen species for catalytic oxidation of toluene

An optimized oxygen activity of catalysts can facilitate oxidation of volatile organic compounds. This work shows the first construction of Ce-Co oxide thin-walled nanoboxes. Bulk-phase lattice oxygen is activated by metal-metal interactions. The subsequent uniform dispersion of low loaded Pt nanoparticles further enhances the surface-adsorbed oxygen content, and creates an oxygen-rich reaction interface. Competitive adsorption of water vapor was also inhibited, and complete catalytic oxidation of toluene was achieved at low temperature (T₉₀ =140 °C). A diffuse reflectance infrared Fourier-transform spectroscopy probe was used to investigate the adsorption-catalytic process and the possible synergistic catalytic mechanism (Langmuir-Hinshelwood and Mars-van Krevelen). This work provides a strategy for improving the catalyt Crystal structure ic oxidation performance of nanocatalysts for volatile organic compounds by increasing the catalytic oxygen activity.

Core-shell structured hollow copper sulfide@metal-organic framework for magnetic resonance imaging guided photothermal therapy in second near-infrared biological window

Multifunctional core-shell hybrids formed by integration of metal-organic framework (MOF) and functional materials have attracted extensive attention as promising theranostic nanoplatforms due to their combined novel properties and enhanced therapeutic efficacy. Recently, the second near-infrared (NIR-II, 1000-1700 nm) laser-induced photothermal therapy (PTT) as compared to the NIR-I(700-950 nm) laser-induced PTT has displayed improved therapeutic effects owing to its merits that include deeper tissue penetration and increased maximum permissible exposure. Herein, a novel core-shell hollow copper sulfide@metal-organic framework (HCuS@MIL-100) has been successfully fabricated by a layer-by-layer technique for the first time and their collective theranostic effects are investigated in vitro and in vivo. In this platform, the inner HCuS was applied as the NIR-II photothermal agent with excellent NIR-II absorption feature, leading to impressive photothermal effects under irradiation by 1064 nm light. With MIL-100 as the shell, HCuS@MIL-100 not only displayed optimal biocompatibility but also presented superior T2 magnetic resonance imaging (MRI) ability. In the current study multifunctional hollow core-shell HCuS@MIL-100 are fabricated for the MRI-guided PTT. This study also offers a facile and effective strategy for the development of novel theranostic platforms with high efficiency through the integration of MOFs and functional materials.

Trimetallic sulfides derived from tri-metal-organic frameworks as anode materials for advanced sodium ion batteries

Highly conductive metal sulfides with high theoretical capacities and good conductivity have been considered as anode material alternatives for sodium-ion batteries (SIBs). Unfortunately, the unsatisfactory cycling stability and poor rate performance are usually resulted from the sluggish electrochemical kinetics and volumetric expansion in the charge/discharge process, which severely restricts their applications. Herein, trimetallic sulfides embedded into the carbon matrix with a microsphere shape (denoted as CoNiZnS/C) were successfully prepared by a facile solid sulfidation of tri-metal-organic frameworks. The nanorods-assembled microsphere structure with abundant phase boundaries of multiphase in the CoNiZnS/C would provide abundant active sites and defects for storing sodium ions and rich voids to alleviate the volumetric strains. As the anode material of SIBs, the optimum composite named as CoNiZnS/C-2 in this work demonstrated high initial Coulombic efficiency (96.52% at 0.1 A g^-1), good cycling stability (maintaining 410.7 mA h g^-1 at the 960th cycle at 2.0 A g^-1) and excellent rate performance (477.0 mA h g^-1 at 5.0 A g^-1). Thus, such a multi-metal sulfide composite with special physical-chemical properties may offer a new insight to promote the electrochemical performance of sulfide-based anode materials for the SIBs.

Mechanism of peroxymonosulfate activation and the utilization efficiency using hollow (Co, Mn)3O4 nanoreactor as an efficient catalyst for degradation of organic pollutants

Development of efficient catalysts for peroxymonosulfate (PMS) activation and further understanding its mechanism on organic pollutants degradation is of significant importance for advanced oxidation processes (AOPs). Herein, hollow (Co, Mn)₃O₄ catalysts were synthesized by calcination of Co, Mn containing metal-organic frameworks (MOFs) and further used to evaluate the effectiveness of organic pollutants (Bisphenol A (BPA), atrazine (ATZ), and diethyl phthalate (DEP)) degradation by PMS activation. The PMS utilization efficiency in (Co, Mn)₃O₄/PMS system (36.4%) was estimated to be 28.0% and 43.8% higher than that of Co₃O₄/PMS and Mn₅O₈/PMS system, respectively. Notably, the metal leaching in (Co, Mn)₃O₄/PMS system was significantly suppressed. The utilization efficiency also reveals an inverse proportionality relationship with BPA mineralization but decreases with increasing initial pH value. A synergy between oxides of Co and Mn was perceived to enhance PMS utilization efficiency and BPA degradation. The results indicate enhanced catalytic performance with (Co, Mn)₃O₄ compared to Co₃O₄ derived from Co-MOF and other reported catalysts, with 99% of BPA degradation within 4 min. The oxidation mechanism was then proposed based on the electron paramagnetic resonance (EPR) and XPS results. Our findings might have contributed to designing heterogeneous catalysts for efficient PMS utilization in AOPs.

Facile synthesis of hierarchical MoS2/ZnS @ porous hollow carbon nanofibers for a stable Li metal anode

Lithium metal is considered as an ideal anode candidate for next generation Li battery systems since its high capacity, low density, and low working potential. However, the uncontrollable growth of Li dendrites and infinite volume expansion impede the commercialized applications of Li-metal anodes. In this work, we rationally designed and constructed a hierarchical porous hollow carbon nanofiber decorated with diverse metal sulfides (MS-ZS@PHC). This composite scaffold has three advantages: First, the synergistic effect of multiple-size lithiophilic phases (nano ZnS and micro MoS₂) can regulate Li ions nuclei and grow up homogenously on the scaffold. Second, the enlarged interplanar spacing of MoS₂ microsphere on the fibers can provide abundant channels for Li ions transportation. Third, the porous scaffold can confine the volume expansion of Li metal anode during cycling. Therefore, in a symmetrical cell, the MS-ZS@PHC host presents a homogenous Li plating/stripping behavior and runs steadily for 1100 h at 5 mA cm^-2 with a capacity of 5 mAh cm^-2 and even for 700 h at 10 mA cm^-2 with a capacity of 1 mAh cm^-2. A full cell using MS-ZS@PHC /Li composite as anode and coupled with LiFePO₄ as cathode delivers an excellent cyclic and rate performances.

Catalytic polysulfides immobilization within a S/C-Co-N hollow cathode obtained by nonthermal imprison route

Lithium-sulfur (Li-S) batteries have hitherto attracted dramatic research interests as an optional high-energy output candidate to replace the traditional lithium-ion batteries on account of its high energy density and low cost. Nonetheless, their kinetics arrearage and detrimental "shuttling effect" caused by the migration of soluble lithium polysulfide (LiPS) intermediates severely limit its practical application. Here, by a nonthermal route sulfur is in-situ imprisoned into Co/N-codoped hollow carbon sphere (NC-Co) to construct an integrated S/C-Co-N hollow cathode (S@NC-Co) and directly applied in Li-S batteries, which effectively avoids complex template removal and sulfur infiltration process. The hollow NC-Co sphere not only restricts polysulfides migration via physical confinement but also enhances polysulfides conversion through redox-active electro-catalysis. Moreover, the hollow structure has large cavity offering sufficient space to accommodate volume expansion and excellent conductivity promising efficient electron/charge transfer. As a result, the batteries assembled by the S@NC-Co cathode achieve low polarization and high-rate capability (551 mAh g^-1 at 4C). Remarkably, the batteries also present an outstanding long-term durability over 800 cycles at 1C, in which the capacity attenuation is merely 0.06 % per cycle. This work demonstrates a novel strategy in designing hierarchical structures or nanoreactors for electrochemical reactions and energy storage systems.

Synthesis of MgNiCo LDH hollow structure derived from ZIF-67 as superb adsorbent for Congo red

Adsorption materials with large specific surface area and porous structures exert a beneficial impact on improving the adsorption performance. In this work, MgNiCo LDH hollow structure (MNC HS) is fabricated through a simple one-step solvothermal method using ZIF-67 as the sacrificial template. Electron microscopy shows that the MNC HS retains the dodecahedral shape of ZIF-67. The as-prepared sample exhibits efficient adsorption for Congo red (CR) in water, which is due to the hierarchical structure and large specific surface area that provides more adsorption sites and electrostatic interaction. The CR adsorption process fits the pseudo-second-order model better by kinetics simulation; while Langmuir model is more accurate than Freundlich model in describing the adsorption isotherms of CR. The maximum adsorption capacity calculated by the Langmuir model can reach 1194.7 mg g^-1, which is much higher than that of the sample MgNiCo LDH (MNC) synthesized by conventional methods. The cycle tests also show that the as-prepared adsorbent has good stability and recycling ability.

Hierarchical NiCo2S4/ZnIn2S4 heterostructured prisms: High-efficient photocatalysts for hydrogen production under visible-light

Exploring low-cost co-catalyst to ameliorate the photocatalytic activity of semiconductors sets a clear direction for solving energy crisis and achieving efficient solar-chemical energy conversion. In this work, a unique hierarchical hollow heterojunction was constructed by in-situ growing ZnIn₂S₄ nanosheets on the porous NiCo₂S₄ hollow prisms through a low temperature solvothermal method, in which NiCo₂S₄ with semi-metal property acted as non-noble metal co-catalyst. NiCo₂S₄ co-catalyst was innovatively encapsulated in ZnIn₂S₄, which not only relieved the light shielding effect caused by the large loading amount of co-catalyst, but also supplied abundant active sites for H₂ evolution. The hierarchical hollow heterostructure of NiCo₂S₄/ZnIn₂S₄ provided a highly efficient channel for charge transfer. Combining these advantages, NiCo₂S₄/ZnIn₂S₄ composite demonstrated excellent photocatalytic activity. In the absence of sacrificial agent, the NiCo₂S₄/ZnIn₂S₄ photocatalyst achieved a remarkable improved H₂ yield of 0.77 mmol g^-1h^-1 under visible light irradiation (λ > 400 nm), which is 6.6 times greater than that of ZnIn₂S₄. Besides, NiCo₂S₄ even exhibited better performance on the H₂ evolution improvement of ZnIn₂S₄ than precious metal Pt. This work will offer novel insights into the reasonable design of non-noble metal photocatalysts with respectable activity for water splitting.

High mass load of oxygen-enriched microporous hollow carbon spheres as electrode for supercapacitor with solar charging station application

Carbon materials modified with pores and heteroatoms have been pursued as promising electrode for supercapacitors due to the synergic storage of electric double-layer capacitance (EDLC) and pseudocapacitance. A vital problem that the actual effect of pores and heteroatoms on energy storage varies with the carbon matrix used presents in numerous carbon electrodes, but is ignored greatly, which limits their sufficient utilization. Moreover, most of modified carbon electrodes still suffer from severe capacitance degeneration under high mass load caused by the blocked surface and inaccessible bulk phase. Here, we shape an interconnected hollow carbon sphere (HCS) as the matrix by regulating and selectively-etching low molecular weight component in the inhomogeneous precursors, accompanied with the decoration of rich oxygen groups (15.9at%) and micropores (centering at 0.6-1.4 nm). Finite-element calculation and energy storage kinetics reveal the modified HCS electrode exposes accessible dual active surface with highly-matched electrons and ions for pores and oxygen groups to improve both EDLC and pseudocapacitance. Under a commercial-level load of 11.2 mg cm^-2, the HCS exhibits a high specific capacitance of 288.3 F g^-1 at 0.5 A g^-1, performing a retention of 91.8% relative to 314 F g^-1 under 2.8 mg cm^-2 load, applicable for solar charging station to efficiently drive portable electronics.

Implantation of Fe7S8 nanocrystals into hollow carbon nanospheres for efficient potassium storage

As a desirable candidate for lithium-ion batteries, potassium-ion batteries (PIBs) have aroused great interest because of their low cost and high power and energy densities. However, the insertion/extraction of K⁺ with a large radius (1.38 Å) usually bring about the destruction of the electrode materials. Here, ultrafine Fe₇S₈ nanocrystals are successfully implanted into hollow carbon nanospheres (Fe₇S₈@HCSs) via a facile solvothermal method and subsequent novel low-temperature sulfurization, which avoid the aggregation of Fe₇S₈ nanoparticles produced during high-temperature sulfidation. The ultrafine Fe₇S₈ nanoparticles and hollow carbon spheres can not only buffer the severe expansion/shrinkage of electrode materials caused by the repeated insertion/extraction of K⁺, but also provide additional accessible pathways for the high-rate K⁺ transmission. When tested as an anode material for PIBs, Fe₇S₈@HCSs achieve impressive K⁺ storage capacity of 523.2 mAh g^-1 at 0.1 A g^-1 after 100 cycles and remarkable rate capacity of 176.3 mAh g^-1 at 5 A g^-1. Further, assembling this anode with a K₂NiFe(CN)₆ cathode yields stable cycling performance, revealing its great potential for large-scale energy storage applications.

Hollow urchin-like Mn3O4 microspheres as an advanced sulfur host for enabling Li-S batteries with high gravimetric energy density

Lithium-sulfur (Li-S) batteries are considered to be promising candidates for next-generation storage systems. However, the practical applications are still hindered by the severe capacity decay, mainly caused by the large volume change, polysulfide shuttle and sluggish sulfur conversion kinetics. Herein, hollow urchin-like Mn₃O₄ (HU-Mn₃O₄) microspheres as sulfur hosts have been synthesized by the hydrothermal method and calcination treatment, aiming to prevent the polysulfide dissolution (benefiting from the strong polysulfide anchoring effect of Mn₃O₄) and alleviate the volume expansion of sulfur (benefiting from the special hollow structure). Meanwhile, the urchin-like thorny surface also facilitates the rapid ion/electron transfer and the abundant active sites for the fast sulfur redox kinetics. When used as the sulfur host in Li-S batteries, the S@HU-Mn₃O₄ cathode delivers a high initial capacity of 1137.4 mAh g^-1 with a slow capacity decay of 0.042% after 200 cycles at 0.2 C. Even under the conditions of lean electrolyte (E/S = 7 mL g^-1) and low N/P ratio (N/P = 2.1), the S@HU-Mn₃O₄ cathode still enables a stable cycling performance with a high gravimetric energy density (202 Wh kg cell^-1), demonstrating its great potential in the development of future practical Li-S battery materials.

Efficient removal of organic pollutants by a Co/N/S-doped yolk-shell carbon catalyst via peroxymonosulfate activation

Carbon-based catalysts with heteroatom doping and hollow structures are desired for advanced oxidation processes (AOPs). Herein, dual-shelled Co, N, and S codoped hollow carbon nanocages were developed by wrapping zeolitic imidazolate framework-67 (ZIF-67) with trithiocyanuric acid (TCA) and performing subsequent carbonization. The optimal composite catalyst (Co-NC-CoS) exhibited excellent catalytic performance toward different organic pollutants. Almost complete removal of 4-NP (60 mg/L^-1) was achieved within 20 min by 10 mg of catalyst and 0.2 g/L^-1 peroxymonosulfate (PMS). Moreover, the catalyst showed good stability and reusability. The effects of catalyst and PMS dose, pollutant concentration, pH and common anions were investigated, and reactive oxygen species (ROS) were studied by scavenger experiments and electron paramagnetic resonance (EPR) tests. The results show that multidoped atoms S, Co and N all contributed to the degradation system. Several lines of evidence suggested that S could change the catalytic process from Co³⁺/Co²⁺ to Co³⁺/Co²⁺/Co⁰ reduction due to its low redox potential. Degradation was achieved through both radical and nonradical pathways, where sulfate radicals (SO₄^·̶), hydroxyl radicals (^·OH) and singlet oxygen (¹O₂) were primary reactive species. Overall, this work may suggest that the novel multi heteroatom-doped catalysts with complex structures can be developed for environmental remediation.

Understanding rich oxygen vacant hollow CeO2@MoSe2 heterojunction for accelerating photocatalytic CO2 reduction

Solar-driven CO₂ reduction into gas fuels is desirable for a sustainable carbon cycle. To improve the photocatalytic activity of CO₂RR, the unique rich oxygen (Vo) vacant hollow CeO₂@MoSe₂ is designed. The introduction of Vo is conducive to the capture of electrons by CO₂ and promotes the process of photocatalytic CO₂RR. The heterojunction formed by introducing the narrow band gap semiconductor MoSe₂ increases the absorption range of visible light and improves the separation efficiency of photogenerated carriers. The hollow structure improves the CO₂ adsorption capacity and improves the use of light effect. Therefore, the prepared H-Vo-CeO₂@49.7 wt% MoSe₂ exhibits enhanced photocatalytic activity for CO₂RR. The yield of CH₄ and CO is 10.2 µmol and 33.2 µmol in 4 h. Moreover, the photocatalytic mechanism is discussed through DFT and in-situ DRIFTS. This work provides new insights to the role of Vo in active CO₂ photoconversion and exploits an important application of CO₂ reduction.

Facile transformation of carboxymethyl cellulose beads into hollow composites for dye adsorption

Novel millimeter hollow microspheres were fabricated from carboxymethyl cellulose microspheres and polyethyleneimine using glutaraldehyde as a crosslinking agent. The hollow microspheres prepared with different polyethyleneimine usages and different polyethyleneimine treatment time were investigated deeply and characterized via SEM-EDX, FT-IR, and BET surface area analysis. It was shown that polyethyleneimine could break the coordination bonds between the carboxyl and Al (III) in carboxymethyl cellulose microspheres, leading to the formation of hollow structures. Most importantly, the usage and treatment time of polyethyleneimine can distinctly tailor the structure of the carboxymethyl cellulose microspheres, resulting in the formation of different hollow microspheres with varied shell thickness and size. Most importantly, we found that the prepared hollow microspheres have excellent adsorption performance toward targeted methyl blue under testing conditions. By virtue of the large accessible amount of -NH₂ groups and its unique hollow structure, this type of millimeter hollow microspheres have broad application prospects in the treatment of emerging contaminants in wastewater.

Hollow Core-Shell potassium Phosphomolybdate@Cadmium Sulfide@Bismuth sulfide Z-Scheme tandem heterojunctions toward optimized Photothermal-Photocatalytic performance

A hollow core-shell potassium phosphomolybdate (KMoP)@cadmium sulfide (CdS)@bismuth sulfide (Bi₂S₃) Z-scheme tandem heterojunction is fabricated by a simple hydrothermal strategy and kept in a water bath to continue the reaction. At the same time, the ternary structure combined Keggin-type polyoxometalate with two photosensitive sulfide semiconductors to form a stable hollow core-shell heterojunction. KMoP@CdS@Bi₂S₃ with a narrow band gap of ∼ 1.2 eV also has excellent photothermal performance, which may further promote photocatalytic efficiency. The hollow core-shell KMoP@CdS@Bi₂S₃ tandem heterojunction shows excellent H₂ production performance, Cr^VI reduction ability and photocatalytic degradation performance of highly toxic tetracycline (TC). Under visible light irradiation, the photocatalytic H₂ generation rate of the KMoP@CdS@Bi₂S₃ tandem heterojunction reaches 831 μmol h^-1, which is 103 times higher than that of pristine KMoP. The photocatalytic reduction efficiency of Cr^VI and degradation efficiency of TC are as high as 95.5 and 97.51%, ∼4 times higher than that of KMoP. The boosted photocatalytic performance can be ascribed to the formation of core-shell Z-scheme tandem heterojunctions favoring spatial charge separation and the narrow band gap, which extends the photoresponse to visible light/NIR regions. When TC and Cr^VI exist at the same time, the reduction efficiency of Cr^VI can be as high as 99.64% because the intermediate of TC degradation can promote the reduction of Cr^VI. In addition, the photocatalytic performance of the KMoP@CdS@Bi₂S₃ heterojunction remains nearly constant after 4 recycles, which indicates high stability. The design strategy may provide new insights for preparing other high-performance core-shell tandem heterojunction photocatalysts for solar energy conversion.

Controlled preparation of hollow Zn0.3Cd0.7S nanospheres modified by NiS1.97 nanosheets for superior photocatalytic hydrogen production

Developing durable and efficient photocatalysts for H₂ evolution is highly desirable to expedite current research on solar-chemical energy conversion. In this work, a novel photocatalytic H₂ evolution system based on Zn_0.3Cd_0.7S/NiS_1.97 nanocomposite was rationally designed for the first time. In this advanced composite structure, NiS_1.97 nanosheets as a co-catalyst were intimately coupled to the inner surface of the hollow spherical Zn_0.3Cd_0.7S. The construction of the hollow spherical shell shortened the distance of charge migration to the surface site and increased the multiple absorption of incident light. The introduction of NiS_1.97 nanosheets increased the light absorption capacity of the composite system and also greatly improved the separation and migration behavior of photo-generated carriers due to its narrower band gap and relatively low conduction band position, which had been confirmed by DRS, EIS and PL. As a result, the hollow Zn_0.3Cd_0.7S/NiS_1.97 composite material exhibited excellent photocatalytic activity. At the loading amount of NiS_1.97 up to 15 at.%, the hollow Zn_0.3Cd_0.7S/NiS_1.97 composite exhibited the best photocatalytic activity with a corresponding H₂ production rate of 22.637 mmol g^-1h^-1, which was 1.42 times and 1.85 times that of hollow Zn_0.3Cd_0.7S and solid Zn_0.3Cd_0.7S, respectively. Moreover, this novel catalyst also displayed a long-term stability without apparent debasement in H₂ evolution activity. It is expected that this work could provide new inspiration to the design and development of other highly active photocatalytic systems for water splitting.

Gold nanodot assembly within a cobalt chalcogenide nanoshell: Promotion of electrocatalytic activity

The assembly of functional nanoparticles within materials with unique architectures can improve the interfacial surfaces, defects, and active sites, which are key factors for the designing novel nanocatalysts. Nano metal-organic framework (NMOF) can be employed to fabricate nanodots-confined nanohybrids for use in electrocatalytic processes. Herein, we report a controlled synthesis of gold nanodot assembly within cobalt chalcogenide nanoshell (dots-in-shell Au/Co_xS_y nanohybrids). A cobalt-based NMOF (the cobalt-based zeolite imidazole framework, ZIF-67) is used as a versatile sacrificial template to yield dots-in-shell Au/Co_xS_y nanohybrids. Due to the synergistic effect of the well-dispersed Au nanodots and the thin Co_xS_y nanoshell, the obtained dots-in-shell Au/Co_xS_y nanohybrids exhibit enhanced performance for the oxygen evolution reaction (OER) with low overpotential values at a current density of 10 mA cm^-2 and a small Tafel slope (343 mV and 62 mV dec^-1, respectively).

Line defects in plasmatic hollow copper ball boost excellent photocatalytic reaction with pure water under ultra-low CO2 concentration

By using a low CO₂ concentration as a C1 source, the design of a plasmonic catalyst that can effectively photocatalytic CO₂ reduction is of great significance for sustainable and ecological development. Herein, the space confinement effect and liquid environment of the molten salt result in uniform hollow structure, while the strong aggressive force furnished via using molten salt enhances the formation of line defects. This special structure can not only provide a large number of active sites but also greatly accelerate the transport of photoinduced charge carriers. The hollow copper ball with line defects (CCu) shows excellent photocatalytic activity with pure water (1028.57 μmol g^-1), and it also shows good catalytic activity even under ultra-low CO₂ content, which far exceeds the catalytic activity of most semiconductor-based catalysts. This work is designed to simultaneously construct line defect and hollow structure in plasmatic metal nanoparticles for efficient photocatalytic CO₂ reduction.

Nickel/Cobalt Molybdate Hollow Rods Induced by Structure and Defect Engineering as Exceptional Electrode Materials for Hybrid Supercapacitor

Oxygen defects and hollow structures positively impact pseudocapacitive properties of diffusion/surface-controlled processes, a component of critical importance when building high-performance supercapacitors. Hence, we fabricated hollow nickel/cobalt molybdate rods with O-defects (D-H-NiMoO₄ @CoMoO₄ ) through a soft-template and partial reduction method, enhancing D-H-NiMoO₄ @CoMoO₄ 's electrochemical performance, yielding a specific capacitance of 1329 F g^-1 , and demonstrating excellent durability with 95.8 % capacity retention after 3000 cycles. D-H-NiMoO₄ @CoMoO₄ was used as the positive electrode to construct an asymmetric supercapacitor, displaying an energy density of up to 34.13 Wh kg^-1 and demonstrating good predisposition towards practical applications. This work presents an effective approach to fabricate and use hollow nickel/cobalt molybdate rods with O-defects as pseudocapacitor material for high-performance capacitive energy storage devices.

Metal-organic framework derived hollow CoFe@C composites by the tunable chemical composition for efficient microwave absorption

Controlling the composition and microstructure of nanomaterials is still a significant challenge in developing high-performance microwave absorption (MA) materials. Herein, metal-organic framework (MOF)-derived hollow CoFe@C nanoboxes are designed and prepared through the facile regulating the mass ratios of ZIF-67/PFC and a thermal annealing treatment. The CoFe@C composite can achieve an excellent MA performance, which have two high reflection loss (RL) values at different thickness. A RL value of -31.0 dB is obtained at 11.84 GHz with a matching thickness of 2.4 mm, and a RL value can reach -44.1 dB (4.08 GHz) at a matching thickness of 5.8 mm, and a correspondingly wide absorbing bandwidth (5.20 GHz, from 9.7 to 14.9 GHz) is simultaneously obtained at a matching thickness of 2.3 mm. The magnetic loss, interfacial polarization and hollow structure are the main reasons for their excellent MA capability. This work provides a research idea for the development of the efficient MOF-based MA materials in practical application.

Design of ultrathin nanosheet subunits ZnIn2S4 hollow nanocages with enhanced photoelectric conversion for ultrasensitive photoelectrochemical sensing

Herein, a high-efficiency photoactive material, hollow ZnIn₂S₄ nanocages (ZIS-HNCs) composed of ultrathin nanosheets were creatively synthesized via a metal-organic framework (MOF) derived solvothermal method. It had been specified the underlying mechanism of the ZIS-HNCs evolution under the MOF templated surface. Subsequently, the obtained ZIS-HNCs combined with annealing TiO₂ modified electrode (ZIS-HNCs@TiO₂), and the ZIS-HNCs@TiO₂ exhibited intense transient photocurrent. The enhanced photocurrent signal benefited from the multiple light capture effect of ZIS-HNCs, ultrathin nanosheet subunits of ZIS-HNCs, and typical type Ⅱ heterojunction, which could effectively retard the photoexcited electron-hole pairs recombination, and accelerated charge separation and transfer. Taking antibiotic lincomycin (Lin) as a model, a signal-off photoelectrochemical (PEC) aptasensor based on the ZIS-HNCs@TiO₂ was established and manifested a high sensitive detection for Lin with a linear response range from 0.0001 to 0.1 nM as well as an ultralow detection limit of 0.084 pM. Additionally, the proposed PEC aptasensor showed acceptable stability and remarkable selectivity. Therefore, this study provides a promising strategy to design nanomaterials with superior photoelectric activity for PEC sensing applications.

Hollow molecularly imprinted fluorescent sensor using europium complex as functional monomer for the detection of trace 2,4,6-trichlorophenol in real water samples

As an important environmental indicator, 2,4,6-trichlorophenol (2,4,6-TCP) was proved extremely harmful to human body. In this article, hollow molecularly imprinted fluorescent polymers (@MIPs) for the selective detection of 2,4,6-TCP were devised and fabricated by sacrificial skeleton method based on SiO₂ nanoparticles. As the most innovation, highly luminescent europium complex Eu(MAA)₃phen played the role of both fluorophores and functional monomers of the MIPs. The obtained @MIPs showed monodispersity and the average particle size was around 130 nm. It had a linear fluorescent response within the concentration range 10-100 nmol L^-1 with the correlation coefficient calculated as 0.99625, and the limit of detection was identified as 2.41 nmol L^-1. The results show that Eu(MAA)₃phen as a fluorophore has high luminescent properties, and as a functional monomer, it can improve the selectivity and anti-interference performance of MIPs. Furthermore, the hollow structure made it possible that the imprinted specific recognition sites distributed on both inner and outer surfaces of @MIPs. The experimental results showed that these @MIPs could be employed to the selective detection of chlorophenols under low concentration. And this work will provide a reference for further optimization of fluorescent imprinted sensors.

Hollow MnFeO oxide derived from MOF@MOF with multiple enzyme-like activities for multifunction colorimetric assay of biomolecules and Hg2

In this work, a new type of hollow MnFeO oxide derived obtained from the metal-organic framework (MOF)@MOF was designed and proposed, which has intrinsic activity of mimicking enzymes of oxidase and peroxidase by adjustment pH values. Based on the colorimetric reaction and the hindrance of the oxidase-like activity in the presence of L-cysteine (Cys), as well as the recovery of oxidase-like activity due to the specific complexation of Cys and mercury (II) ions (Hg²⁺), a new type of colorimetric transmission platform for Cys and Hg²⁺ detection with wide linear ranges of 1-25 μM for Cys and 0.1-15 μM for Hg²⁺ has been developed. Besides, a better colorimetric sensing platform for detecting H₂O₂ was established with linear ranges of 1-60 μM and 60-300 μM based on generating hydroxyl radicals (·OH). Furthermore, the hollow MnFeO oxide has high stability, excellent selectivity with good activity over a long period of time. Surprisingly, the proposed method for Cys, Hg²⁺ and H₂O₂ estimation can also be used in actual samples. These characteristics lay a foundation for further investigation about the catalytic activity of the hollow MnFeO oxide nanomaterials and make it show broad prospects in the field of biosensing and catalysis.

Decomposition of highly persistent perfluorooctanoic acid by hollow Bi/BiOI1-xFx: Synergistic effects of surface plasmon resonance and modified band structures

Perfluorooctanoic acid (PFOA) is highly stable due to the strong CF bond and extremely difficult to be removed by conventional photocatalysts. In this study, Bi doped BiOI_1-xF_x solid solutions with hollow microsphere structure were prepared through a facile one-step hydrothermal method. Compared with pure BiOI and BiOF, the band gap of the Bi/BiOI_1-xF_x solid solutions was significantly reduced, thus promoting the visible light absorbance. The cavity structure of the BiOI_1-xF_x solid solutions enhanced the surface areas and active sites for reaction. The local electromagnetic field dominated by surface plasmon resonance (SPR) effect of Bi metal on the surface favored the separation of the photoinduced charge pairs. As a consequence, Bi/BiOI_0.8F_0.2 (x = 0.20, the doping amount of fluorine was 20 %) composite displayed the best photocatalytic performance for decomposing PFOA, and 40 mg/L PFOA could be removed within 2 h illumination. The degradation rate constant (k = 0.0375 min^-1) of PFOA by Bi/BiOI_0.8F_0.2 was about tenfold of that by pure BiOI and BiOF. Superoxide radical (·O₂-) predominated in the degradation of PFOA by Bi/BiOI_0.8F_0.2, and the possible degradation pathway of PFOA by Bi/BiOI_0.8F_0.2 was proposed. This work provides a highly efficient catalyst for the practical application in removal of highly persistent PFOA.

Prepared PANI@nano hollow carbon sphere adsorbents with lappaceum shell like structure for high efficiency removal of hexavalent chromium

Herein, the novel polyaniline@nano hollow carbon sphere (PANI@NHCS) adsorbents with different mass of NHCS were prepared by in-situ polymerization method. The microstructure of obtained PANI@NHCS-10, PANI@NHCS-20, PANI@NHCS-30 and PANI@NHCS-40 samples were observed through both scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which showed that the PANI@NHCS-30 possessed hollow structure like lappaceum shell. Then, the performance of obtained PANI@NHCS-30 was studied for removing hexavalent chromium (Cr(VI)) from waste water. With the help of unique hollow structure and reduction ability of PANI@NHCS-30, the Cr(VI) was fleetly adsorbed and then reduced to less toxic Cr(III). The maximum adsorption capacity was 250.0 mg/g for PANI@NHCS-30 under the optimal condition. Moreover, the effects of initial Cr(VI) concentration, solution pH and different ions on the adsorption performance were investigated in detail. Importantly, the PANI@NHCS-30 still shows superb adsorption ability after five cycles, which suggests its satisfactory reusability ability. The accumulated data revealed the crucial role of PANI and hollow structure co-promoting effect on Cr(VI) reduction reactions over PANI@NHCS-30, which could be applied to the practical use.

Controllable synthesis of a hollow core-shell Co-Fe layered double hydroxide derived from Co-MOF and its application in capacitive deionization

Capacitive deionization (CDI) is considered one of the most promising desalination technologies for obtaining fresh water from saline water. In this work, we synthesized a hollow core-shell Co-MOF@Fe/Co-LDH (Co-Fe-LDH) material by developing a strategy to simultaneously grow Co/Fe-LDH on the surface of a Co-MOF precursor in situ. Owing to the increase in the specific surface area of the hollow structure and the Faradaic process of a layered double hydroxide (LDH), the Co-Fe-LDH material exhibits high electrical double layer (EDL) capacitance and pseudocapacitance, which significantly improves the salt adsorption of the material during CDI (34.2 mg/g in a 600 mg/L NaCl solution at 1.2 V). The adsorption for NaCl in this work is approximately 2.5 times the maximum salt adsorption capacity (SAC) of LDH materials applied in nonmembrane CDI (NMCDI). This work may provide a promising model for the application of hollow LDH materials that exhibit pseudocapacitance in CDI.

Controlled morphology and dimensionality evolution of NiPd bimetallic nanostructures

Controlling the morphology of noble metal-based nanostructures is a powerful strategy for optimizing their catalytic performance. Here, we report a one-pot aqueous synthesis of versatile NiPd nanostructures at room temperature without employing organic solvents or surfactants. The synthesis can be tuned to form zero-dimensional (0D) architectures, such as core-shell and hollow nanoparticles (NPs), as well as nanostructures with higher dimensionality, such as extended nanowire networks and three-dimensional (3D) nanodendrites. The diverse morphologies were successfully obtained through modification of the HCl concentration in the Pd precursor solution, and the reaction aging time. An in-depth understanding of the formation mechanism and morphology evolution are described in detail. A key factor in the structural evolution of the nanostructures was the ability to tune the reduction rate and to protonate the citrate stabiliser by adding HCl. Spherical core-shell NPs were formed by the galvanic replacement-free deposition of Pd on Ni NPs which can be transformed to hollow NPs via a corrosion process. High concentrations of HCl led to the transition of isotropic spherical NPs into anisotropic wormlike nanowire networks, created through an oriented attachment process. Aging of these nanowire networks resulted in the formation of 3D porous nanodendrites via a corrosion process. The diverse structures of NiPd NPs were anchored onto acid treated-activated carbon (AC) and exhibited improved catalytic efficiency towards the hydrogenation of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP).

Resveratrol-loaded hollow kafirin nanoparticles via gallic acid crosslinking: An evaluation compared with their solid and non-crosslinked counterparts

The possibility of combining the health benefits of kafirin and polyphenols and improving the bioavailability of resveratrol using hollow kafirin nanoparticles via gallic acid crosslinking was investigated. The size, morphology, charge state, loading efficiency, physicochemical stability, and redispersity after lyophilization of hollow resveratrol-loaded kafirin nanoparticles formed via gallic acid crosslinking were characterized and compared with their solid counterparts and those without crosslinking. The nanoparticles formed were anionic spheres with an average diameter of <100 nm when loading amounts of resveratrol were less than 20%. The hollow nanoparticles were homogenous and still achieved stable colloidal dispersion after lyophilization. The hollow nanoparticles crosslinked with gallic acid displayed stability against pancreatin and delayed release in stimulated digestion. The results suggested that hollow kafirin nanoparticles could be a favorable colloidal delivery system for incorporating resveratrol.

Facile synthesis of copper doping hierarchical hollow porous hydroxyapatite beads by rapid gelling strategy

Calcium phosphate based ceramic materials are widely used in bone tissue engineering. Till now, it remains an unmet challenge to construct monodispersed hollow porous calcium phosphate beads through facile and scalable-production strategy. Herein, a rapid gelling strategy is used to combine the guar gum and metal hydroxide, which helps to prepare hollow hierarchical porous hydroxyapatite beads. Results show that the concentration of copper ions and calcination temperature greatly affect the microstructure transformation of the product. Higher concentrations of copper ions lead to the growth of hollow structures, and these ceramic beads exhibit excellent biocompatibility and antibacterial properties. The structure evolution of the products is systematically investigated, and a formation mechanism has been proposed.

A metal-free and preconcentration-free method for non-enzymatic amperometric determination of pentachlorophenol using a ZIF-derived hollow carbon material

An enzyme-free, metal-free, and preconcentration-free electrochemical sensor for pentachlorophenol assay has been fabricated. The interface of the sensor is based on a hollow zeolitic imidazolate framework-derived mesoporous carbon material (denoted as HZC/SPCE). The sensor exhibits linear amperometric response upon pentachlorophenol at 0.82 V (vs. Ag/AgCl) in the concentration range 0.001 to 26.8 mg L^-1 (3.75 × 10^-8~1.006 × 10^-4 M) (R² = 0.997). The sensitivity of HZC/SPCE is 3.53 × 10² μA mM^-1 cm^-2 with a detection limit of 2.05 × 10^-9 M (S/N = 3) for pentachlorophenol. The method has been applied to the determination of pentachlorophenol in spiked food packaging samples with recoveries in the range 92.0 to 107.0%. Graphical abstract Schematic representation of the synthesis of hollow ZIFs-derived hollow carbon material. Free protons derived from tannic acid penetrated into ZIF-8 to destroy its solid framework and the outer parts covered by tannic acid were protected from further etching. After pyrolysis, the morphology of HZC remained similar to that of HZIF-8. Abbreviation: CTAB: hexadecyl trimethyl ammonium bromide; Melm: 2-methylimidazole; ZIF-8: zeolitic imidazolate framework-8; TA: tannic acid; HZIF-8: hollow zeolitic imidazolate framework-8; HZC: hollow zeolitic imidazolate frameworks (ZIFs)-derived mesoporous carbon material.

Fabrication of porous Na3V2(PO4)3/reduced graphene oxide hollow spheres with enhanced sodium storage performance

Sodium-ion batteries (SIBs) have long been recognized as a potential substitute for lithium-ion batteries, while their practical application is greatly hindered owing to the absence of suitable cathode materials with improved rate capability and prolonged cycling life. Na₃V₂(PO₄)₃ (NVP) has drawn extensive attention among the cathode materials for SIBs because of its fast Na⁺-transportable framework which enables high-speed charge transfer, but the poor electric conductivity of NVP significantly restricts the Na⁺ diffusion. To tackle this issue, in this work, porous NVP/reduced graphene oxide hollow spheres (NVP/rGO HSs) are constructed via a spray drying strategy. Due to the unique porous hollow architecture, the synthesized compound manifests a high reversible capacity of 116 mAh g^-1 at 1 C (1 C = 118 mA g^-1), an outstanding high-rate capability of 107.5 mAh g^-1 at 10 C and 98.5 mAh g^-1 at 20 C, as well as a stable cycling performance of 109 mAh g^-1 after 400 cycles at 1 C and 73.1 mAh g^-1 after 1000 cycles at 10 C. Moreover, galvanostatic intermittent titration technique demonstrates that the Na⁺ diffusion coefficient of NVP/rGO HSs is an order of magnitude larger than the pristine NVP. The remarkable electrochemical properties of NVP/rGO HSs in full cells further enable it a potential cathode for SIBs.

Rational Design of Ni(OH)2 Hollow Porous Architecture for High-Sensitivity Enzyme-Free Glucose Sensor

Ni(OH)₂ electrocatalysts have acquired lots of research attentions as ideal substitutes for noble metals. However, their electrocatalytic performance still cannot meet the demands for applications due to the difficulties in electron transfer and mass transport. According to kinetics principle, the construction of hollow structure is regarded as an effective method to achieve outstanding electrocatalytic performance. In this work, Ni(OH)₂ hollow porous architecture (Ni(OH)₂ HPA) was simply synthesized through a coordinating etching and precipitating (CEP) method for the building of enzymatic-free glucose sensors. Ni(OH)₂ HPA presents large specific surface area (SSA), ordered diffusion channels, and structure stability. As a detection electrode for glucose, Ni(OH)₂ HPA exhibits eminent electroactivity in terms of high sensitivity (1843 μA mM^-1 cm^-2), lower detection limit (0.23 μM), and short response time (1.4 s). The results demonstrate that Ni(OH)₂ HPA has practical applications for construction of enzymatic-free electrochemical sensors. The design of hollow structure also provides an effective engineering method for high-performance sensors.

Synthesis of hollow lantern-like Eu(III)-doped g-C3N4 with enhanced visible light photocatalytic perfomance for organic degradation

A series of hollow structure lantern-like Eu(III)-doped g-C₃N₄ (xEu-CN, x = 1, 2, 3) was firstly synthesized by heating a mixture of melamine, HNO₃ and Eu₂O₃ at 500 °C for 2 h. The phase, morphology and optical properties of the serial xEu-CN samples were characterized by different techniques, including TEM, XRD, FT-IR, SEM, XPS, BET, UV-vis, PL, photocurrent, and EIS. The results indicated that Eu doping extraordinarily enhanced the photocatalytic activity of pure g-C₃N₄, and the 2Eu-CN exhibited the highest photocatalytic performance with a 98% (82%) degradation rate for RhB (TC), 6.03 (1.71)-fold of pure g-C₃N₄(CN). The higher photocatalytic efficiency is ascribed to the synergy effect of Eu(III) and the hollow structures, which led to a larger surface specific area, bandgap narrowing, enhanced light harvesting ability and efficient charge separation.

Ag-HPBs by a coating-etching strategy and their derived injectable implants for enhanced tumor photothermal treatment

Herein, we demonstrate a coating-etching strategy to directly synthesize hollow Prussian blue (PB) nanocubes with well-dispersed Ag nanoparticles (denoted as Ag-HPB). The method is accomplished by introduction of PB precursors, K₃Fe(CN)₆ and Fe³⁺ into a reaction system containing AgNO₃ and ascorbic acid, in which a series reactions contain formation of Ag nanoparticles, coating of PB on the nanoparticles, and diffusion of Ag into the PB frameworks occur. The strategy for preparation of the hollow structured Ag-HPB is intrinsically simple and does not require pre-preparation of any sacrificial templates or toxic etching agents. The obtained Ag-HPB nanocubes possess uniform size (69 nm), well-defined hollow structure, strong near-infrared photothermal conversion capacity, and excellent photoacoustic and magnetic resonance imaging abilities. Furthermore, an injectable photothermal implants are prepared for the first time by mixing the Ag-HPB nanocubes with clinically used biological glue, which significantly enhance photothermal anti-tumor efficacy, showing great potential for clinical tumor treatment.