A Tissue-Like Soft All-Hydrogel Battery

Edible batteries for biomedical innovation: advances, challenges, and future perspectives

In biomedical applications, the demand for advanced electronic devices that enable precise monitoring, targeted therapies, and non-invasive diagnostic tools is steadily increasing to enhance patient outcomes. Edible batteries seamlessly combine biocompatibility, energy efficiency, and safe ingestion, offering a reliable power source for in vivo devices and opening up new possibilities for innovative healthcare solutions. Beyond supporting precise monitoring and advanced therapeutic interventions, edible batteries overcome the inherent limitations of traditional batteries, such as rigidity, toxicity, and environmental concerns. Their unique properties make them essential for advancing precision medicine and promoting sustainable biomedical technologies. This transformative approach marks a significant leap in the evolution of battery technology for biomedical engineering applications. This review systematically categorizes edible batteries into various types, including lithium-based, sodium-based, magnesium-based, zinc-based, and other emerging systems. It further highlights key distinctions in material selection, structural design, and fabrication techniques, examining their influence on electrochemical performance and suitability for biomedical applications. Additionally, the review identifies existing challenges and outlines prospective research directions, paving the way for further advancements in this innovative field.

Silk fibroin-based hydrogels with low hysteresis, self-adhesion, and tunable ionic conductivity for wearable devices

Silk Fibroin (SF) hydrogels are easy to functionalize and possess biocompatibility, making them highly promising for the development of flexible electronic devices and wearable equipment. However, fabricating SF-based hydrogels with multiple functions such as low hysteresis, self-adhesion, and high elasticity, while constructing flexible wearable electronic devices with high sensitivity and fidelity, remains a challenge to date. To address these issues, this work reports a one-step preparation of a fully polymer-based triple-network hydrogel through precursor solution pH pre-regulation, with polyacrylamide (PAM) as a brittle network, methyl cellulose (MC) as a tough network, and SF as a zwitterionic macromolecule. The introduction of MC effectively regulate the network aperture of the hydrogel, so as to improve the ion transport capacity and realize the high conductivity of the hydrogel. Through the regulation of the precursor solution pH, the cross-linking degree of the PAM network, the hydrogen bonding interactions between the triple networks, and the interfacial properties were simultaneously modulated, resulting in a reduction in hysteresis of the hydrogel from 21.4 % to 7.2 %, an increase in conductivity from 0.34 S·m-1 to 0.57 S·m-1, an increase in elastic modulus from 18.6 kPa to 58.9 kPa, and an improvement in interfacial adhesion from 4.5 kPa to 15.48 kPa. The prepared SF-based hydrogel was assembled into flexible electronic patches and adhered to different parts of the human body, enabling self-adhesive, multi-channel, wireless detection of human multi-scale movements. The hydrogel prepared in this work also demonstrates exceptional potential in fields such as electrocardiogram monitoring, electromyogram detection, information encryption, and self-powered devices. The method reported in this paper provides new insights for the synergistic enhancement of mechanics, electricity, and adhesion in natural polymer-based hydrogels.

Heparin Doped Polyaniline for Anticoagulation Supercapacitors

With the rapid development of implantable electronic medical devices, supercapacitors have gained significant attention as implantable energy storage devices due to their inherent advantages. However, these devices inevitably direct contact with blood and trigger coagulation or thrombus formation when implanted in the body. In severe cases, these negative effects compromise the functionality of the implantable energy storage system and even jeopardize human health. Herein, a biocompatible electrode material with high anticoagulant activity is designed by doping polyaniline with anticoagulant macromolecule heparin under neutral conditions, which macromolecules as dopants under neutral conditions not only avoids the toxicity of acids to biological tissues and de-doping caused by small molecules, but also imparts high anticoagulant properties to the material. Based on the electrode material and in situ polymerization approach, an all-in-one anticoagulation supercapacitor is employed to manufacture and exhibits good electrochemical performance (energy density of 18.89 µWh cm-2 and a power density of 197.8 µW cm-2), cycling stability (capacitance retention of 70.23% after 2, 000 cycles), anticoagulant performance (APTT is 15.47 s, PT is 16.57 s, TT is 49.47 s, and FIB is 1.12 g L-1), and tissue compatibility. The doping strategy provides a valuable reference for energy supply in implantable bioelectronics.

High-voltage water-scarce hydrogel electrolytes enable mechanically safe stretchable Li-ion batteries

Soft Li-ion batteries, based on conventional organic electrolytes, face performance degradation challenges due to moisture penetration and safety concerns due to possible leakage of toxic fluorine compounds and flammable solvents under mechanical damage. We design a water-scarce hydrogel electrolyte with fluorine-free lithium salt to achieve wide electrochemical stability window (up to 3.11 volts) in ambient air without hermetic packaging while balancing high stretchability (1348%), ion conductivity (41 millisiemens per centimeter), and self-healing capabilities for mechanically and chemically safe stretchable Li-ion batteries. Molecular synergy between hydrophilicity and lithiophilicity of zwitterionic polymer backbone is revealed by molecular dynamics simulations. The battery exhibits capacity retention under harsh mechanical stresses-enduring stretching, twisting, folding, and multiple through-punctures by a needle-while self-healing from repeated through cuts by a razor blade. Stable ambient operation for 1 month over 500 charge-discharge cycles (average coulomb efficiency, 95%) is achieved. A prototype self-healing electronic system with embedded soft batteries demonstrates practical application as a durable embodied energy source.

Make it flow from solid to liquid: Redox-active electrofluids for intrinsically stretchable batteries

High-capacity stretchable batteries are crucial for next-generation wearables to enable long-term operation and mechanical conformability with the human user. In existing stretchable battery designs, increasing the active material to yield higher capacity often leads to thicker and stiffer solid electrodes with poor mechanical properties. Here, we present a concept that transfers the physical property of a battery electrode from a conventional solid into a fluid state. The mechanical and electrochemical properties of the electrode rely on the viscosity of fluids rather than Young's modulus of solids. Fluids conform easily into any shape with minimal force, making them intrinsically deformable. This decouples the electrochemical and mechanical property of the redox-active electrofluid, leading to higher capacities with more active material loading without stiffening the cell. The cell showed excellent capacity retention over 500 charge-discharge cycles and mechanical robustness up to 100% strain. Our work provides a technological solution for stretchable batteries that balances capacity and mechanical performance.

Photopatternable PEDOT:PSS Hydrogels for High-Resolution Photolithography

Conducting polymer hydrogels have been extensively explored toward diverse applications like bioelectronics and soft robotics. However, the fabrication resolution of conducting polymer hydrogels by typical techniques, including ink-jet printing, 3D-printing, etc., has been generally limited to >10 µm, significantly restricting rapid innovations and broad applications of conducting polymer hydrogels. To address this issue, a photosensitive biphasic conducting polymer hydrogel (PB-CH) is rationally designed and synthesized, comprising poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as the conductive phase and a light-sensitive matrix as the mechanical phase. The formation of phase-separated structures within PB-CH preserves the integrity of the conductive channels during the photoinitiated cross-linking. This minimizes the conductivity loss, a common limitation in similar materials. Remarkably, the resultant PB-CH exhibits a combination of excellent electrical conductivity (≈30 S cm-1), robust mechanical performance (tensile strain up to 50%), and high photopatternability. A detailed investigation of the photolithography process identifies key technological parameters that enable high-resolution patterning of 5 µm. By simultaneously maintaining processability, conductivity, and mechanical flexibility, this PB-CH represents an ideal candidate for advanced flexible electronic applications, offering a new technique to fabricating high-performance conducting polymer hydrogels.

Self-Healing and Antifreezing/Antidrying Conductive Eutectohydrogel-Based Biosignal Monitoring Multisensors with Integrated Supercapacitor

A novel self-healing and antifreezing/antidrying conductive eutectohydrogel, ideal for wearable multifunctional sensors and supercapacitors, is reported. Conductive eutectohydrogel with self-healing and facilely tunable mechanical performance is obtained by incorporation of trehalose and phytic acid as reversible cross-linkers into a polyacrylamide network, forming the dynamic hydrogen bonding and electrostatic interactions. Furthermore, combined use of deep eutectic solvent with water ensures the air stability as well as the antifreezing/antidrying characteristics. The synthesized eutectohydrogel exhibits a self-healing efficiency of 90.7% after 24 h at room temperature, Young's modulus of 140.9 kPa, and strain at break of 352.8%. With the eutectohydrogel as a versatile platform, self-healing strain and temperature sensors, electrocardiogram electrodes, and supercapacitor are fabricated, recovering the device performance after self-healing from complete bisection and exhibiting stable performance over a wide temperature range from -20 to 50 °C. With a vertically integrated patch device of supercapacitor and strain sensor attached onto skin, various body movements are successfully detected using the energy stored in the supercapacitor, without performance degradation even after self-healing from complete bisection of the full patch device. This work demonstrates high potential application of the synthesized eutectohydrogel to flexible wearable devices featuring durability and longevity.

Energetic and durable all-polymer aqueous battery for sustainable, flexible power

All-polymer aqueous batteries, featuring electrodes and electrolytes made entirely from polymers, advance wearable electronics through their processing ease, inherent safety, and sustainability. Challenges persist with the instability of polymer electrode redox products in aqueous environments, which fail to achieve high performance in all-polymer aqueous batteries. Here, we report a polymer-aqueous electrolyte designed to stabilize polymer electrode redox products by modulating the solvation layers and forming a solid-electrolyte interphase. Polyaniline is selected as an example for its dual functionality as a cathode or anode working by p/n doping mechanisms. This approach pioneers the application of polyaniline as an anode and enhances the high-voltage stability of polyaniline cathode in an aqueous electrolyte. The resulting all-polymer aqueous sodium-ion battery with polyaniline as symmetric electrodes exhibits a high capacity of 139 mAh/g, energy density of 153 Wh/kg, and a retention of over 92% after 4800 cycles. Spectroscopic characterizations have elucidated the hydration structure, solid-electrolyte interphase, and dual-ion doping mechanism. Large-scale all-polymer flexible batteries are fabricated with excellent flexibility and recyclability, heralding a paradigmatic approach to sustainable, wearable energy storage.

A Bio-Inspired Multifunctional Hydrogel Network with Toughly Interfacial Chemistry for Dendrite-Free Flexible Zinc Ion Battery

Flexible and high-performance aqueous zinc-ion batteries (ZIBs), coupled with low cost and safe, are considered as one of the most promising energy storage candidates for wearable electronics. Hydrogel electrolytes present a compelling alternative to liquid electrolytes due to their remarkable flexibility and clear advantages in mitigating parasitic side reactions. However, hydrogel electrolytes suffer from poor mechanical properties and interfacial chemistry, which limits them to suppressed performance levels in flexible ZIBs, especially under harsh mechanical strains. Herein, a bio-inspired multifunctional hydrogel electrolyte network (polyacrylamide (PAM)/trehalose) with improved mechanical and adhesive properties was developed via a simple trehalose network-repairing strategy to stabilize the interfacial chemistry for dendrite-free and long-life flexible ZIBs. As a result, the trehalose-modified PAM hydrogel exhibits a superior strength and stretchability up to 100 kPa and 5338 %, respectively, as well as strong adhesive properties to various substrates. Also, the PAM/trehalose hydrogel electrolyte provides superior anti-corrosion capability for Zn anode and regulates Zn nucleation/growth, resulting in achieving a high Coulombic efficiency of 98.8 %, and long-term stability over 2400 h. Importantly, the flexible Zn//MnO2 pouch cell exhibits excellent cycling performance under different bending conditions, which offers a great potential in flexible energy-related applications and beyond.

One-Dimensional Implantable Sensors for Accurately Monitoring Physiological and Biochemical Signals

In recent years, one-dimensional (1D) implantable sensors have received considerable attention and rapid development in the biomedical field due to their unique structural characteristics and high integration capability. These sensors can be implanted into the human body with minimal invasiveness, facilitating real-time and accurate monitoring of various physiological and pathological parameters. This review examines the latest advancements in 1D implantable sensors, focusing on the material design of sensors, device integration, implantation methods, and the construction of the stable sensor-tissue interface. Furthermore, a comprehensive overview is provided regarding the applications and future research directions for 1D implantable sensors with an ultimate aim to promote their utilization in personalized healthcare and precision medicine.

Advanced Energy Harvesters and Energy Storage for Powering Wearable and Implantable Medical Devices

Wearable and implantable active medical devices (WIMDs) are transformative solutions for improving healthcare, offering continuous health monitoring, early disease detection, targeted treatments, personalized medicine, and connected health capabilities. Commercialized WIMDs use primary or rechargeable batteries to power their sensing, actuation, stimulation, and communication functions, and periodic battery replacements of implanted active medical devices pose major risks of surgical infections or inconvenience to users. Addressing the energy source challenge is critical for meeting the growing demand of the WIMD market that is reaching valuations in the tens of billions of dollars. This review critically assesses the recent advances in energy harvesting and storage technologies that can potentially eliminate the need for battery replacements. With a key focus on advanced materials that can enable energy harvesters to meet the energy needs of WIMDs, this review examines the crucial roles of advanced materials in improving the efficiencies of energy harvesters, wireless charging, and energy storage devices. This review concludes by highlighting the key challenges and opportunities in advanced materials necessary to achieve the vision of self-powered wearable and implantable active medical devices, eliminating the risks associated with surgical battery replacement and the inconvenience of frequent manual recharging.

Stretchable and biodegradable plant-based redox-diffusion batteries

The redox-diffusion (RD) battery concept introduces an environmentally friendly solution for stretchable batteries in autonomous wearable electronics. By utilising plant-based redox-active biomolecules and cellulose fibers for the electrode scaffold, separator membrane, and current collector, along with a biodegradable elastomer encapsulation, the battery design overcomes the reliance on unsustainable transition metal-based active materials and non-biodegradable elastomers used in existing stretchable batteries. Importantly, it addresses the drawback of limited attainable battery capacity, where increasing the active material loading often leads to thicker and stiffer electrodes with poor mechanical properties. The concept decouples the active material loading from the mechanical structure of the electrode, enabling high mass loadings, while retaining a skin-like young's modulus and stretchability. A stretchable ion-selective membrane facilitates the RD process, allowing two separate redox couples, while preventing crossovers. This results in a high-capacity battery cell that is both electrochemically and mechanically stable, engineered from sustainable plant-based materials. Notably, the battery components are biodegradable at the end of their life, addressing concerns of e-waste and resource depletion.

Exploring role of microbatteries in enhancing sustainability and functionality of implantable biosensors and bioelectronics

Microbatteries are emerging as a sustainable, miniaturized power source, crucial for implantable biomedical devices. Their significance lies in offering high energy density, longevity, and rechargeability, facilitating uninterrupted health monitoring and treatment within the body. The review delves into the development of microbatteries, emphasizing their miniaturization and biocompatibility, crucial for long-term, safe in-vivo use. It examines cutting-edge manufacturing techniques like physical and chemical vapor deposition, and atomic layer deposition, essential for the precision manufacture of the microbatteries. The paper contrasts primary and secondary batteries, highlighting the advantages of zinc-ion and magnesium-ion batteries for enhanced stability and reduced reactivity. It also explores biodegradable batteries, potentially obviating the need for surgical extraction post-use. The integration of microbatteries into diagnostic and therapeutic devices is also discussed, illustrating how they enhance the efficacy and sustainability of implantable biosensors and bioelectronics.

Multifunctional Conductive Hydrogel Interface for Bioelectronic Recording and Stimulation

The past few decades have witnessed the rapid advancement and broad applications of flexible bioelectronics, in wearable and implantable electronics, brain-computer interfaces, neural science and technology, clinical diagnosis, treatment, etc. It is noteworthy that soft and elastic conductive hydrogels, owing to their multiple similarities with biological tissues in terms of mechanics, electronics, water-rich, and biological functions, have successfully bridged the gap between rigid electronics and soft biology. Multifunctional hydrogel bioelectronics, emerging as a new generation of promising material candidates, have authentically established highly compatible and reliable, high-quality bioelectronic interfaces, particularly in bioelectronic recording and stimulation. This review summarizes the material basis and design principles involved in constructing hydrogel bioelectronic interfaces, and systematically discusses the fundamental mechanism and unique advantages in bioelectrical interfacing with the biological surface. Furthermore, an overview of the state-of-the-art manufacturing strategies for hydrogel bioelectronic interfaces with enhanced biocompatibility and integration with the biological system is presented. This review finally exemplifies the unprecedented advancement and impetus toward bioelectronic recording and stimulation, especially in implantable and integrated hydrogel bioelectronic systems, and concludes with a perspective expectation for hydrogel bioelectronics in clinical and biomedical applications.

Fibres-threads of intelligence-enable a new generation of wearable systems

Fabrics represent a unique platform for seamlessly integrating electronics into everyday experiences. The advancements in functionalizing fabrics at both the single fibre level and within constructed fabrics have fundamentally altered their utility. The revolution in materials, structures, and functionality at the fibre level enables intimate and imperceptible integration, rapidly transforming fibres and fabrics into next-generation wearable devices and systems. In this review, we explore recent scientific and technological breakthroughs in smart fibre-enabled fabrics. We examine common challenges and bottlenecks in fibre materials, physics, chemistry, fabrication strategies, and applications that shape the future of wearable electronics. We propose a closed-loop smart fibre-enabled fabric ecosystem encompassing proactive sensing, interactive communication, data storage and processing, real-time feedback, and energy storage and harvesting, intended to tackle significant challenges in wearable technology. Finally, we envision computing fabrics as sophisticated wearable platforms with system-level attributes for data management, machine learning, artificial intelligence, and closed-loop intelligent networks.

Recent Advances of Stretchable Nanomaterial-Based Hydrogels for Wearable Sensors and Electrophysiological Signals Monitoring

Electrophysiological monitoring is a commonly used medical procedure designed to capture the electrical signals generated by the body and promptly identify any abnormal health conditions. Wearable sensors are of great significance in signal acquisition for electrophysiological monitoring. Traditional electrophysiological monitoring devices are often bulky and have many complex accessories and thus, are only suitable for limited application scenarios. Hydrogels optimized based on nanomaterials are lightweight with excellent stretchable and electrical properties, solving the problem of high-quality signal acquisition for wearable sensors. Therefore, the development of hydrogels based on nanomaterials brings tremendous potential for wearable physiological signal monitoring sensors. This review first introduces the latest advancement of hydrogels made from different nanomaterials, such as nanocarbon materials, nanometal materials, and two-dimensional transition metal compounds, in physiological signal monitoring sensors. Second, the versatile properties of these stretchable composite hydrogel sensors are reviewed. Then, their applications in various electrophysiological signal monitoring, such as electrocardiogram monitoring, electromyographic signal analysis, and electroencephalogram monitoring, are discussed. Finally, the current application status and future development prospects of nanomaterial-optimized hydrogels in wearable physiological signal monitoring sensors are summarized. We hope this review will inspire future development of wearable electrophysiological signal monitoring sensors using nanomaterial-based hydrogels.

Gels/Hydrogels in Different Devices/Instruments-A Review

Owing to their physical and chemical properties and stimuli-responsive nature, gels and hydrogels play vital roles in diverse application fields. The three-dimensional polymeric network structure of hydrogels is considered an alternative to many materials, such as conductors, ordinary films, constituent components of machines and robots, etc. The most recent applications of gels are in different devices like sensors, actuators, flexible screens, touch panels, flexible storage, solar cells, batteries, and electronic skin. This review article addresses the devices where gels are used, the progress of research, the working mechanisms of hydrogels in those devices, and future prospects. Preparation methods are also important for obtaining a suitable hydrogel. This review discusses different methods of hydrogel preparation from the respective raw materials. Moreover, the mechanism by which gels act as a part of electronic devices is described.

Improvements and Challenges of Hydrogel Polymer Electrolytes for Advanced Zinc Anodes in Aqueous Zinc-Ion Batteries

Aqueous zinc-ion batteries (AZIBs) are widely regarded as desirable energy storage devices due to their inherent safety and low cost. Hydrogel polymer electrolytes (HPEs) are cross-linked polymers filled with water and zinc salts. They are not only widely used in flexible batteries but also represent an ideal electrolyte candidate for addressing the issues associated with the Zn anode, including dendrite formation and side reactions. In HPEs, an abundance of hydrophilic groups can form strong hydrogen bonds with water molecules, reducing water activity and inhibiting water decomposition. At the same time, special Zn2+ transport channels can be constructed in HPEs to homogenize the Zn2+ flux and promote uniform Zn deposition. However, HPEs still face issues in practical applications, including poor ionic conductivity, low mechanical strength, poor interface stability, and narrow electrochemical stability windows. This Review discusses the issues associated with HPEs for advanced AZIBs, and the recent progresses are summarized. Finally, the Review outlines the opportunities and challenges for achieving high performance HPEs, facilitating the utilization of HPEs in AZIBs.

Asymmetric Hydrogel Electrolyte Featuring a Customized Anode and Cathode Interfacial Chemistry for Advanced Zn-I2 Batteries

An integrated asymmetric hydrogel electrolyte with a tailored composition and chemical structure on the cathode/anode-electrolyte interface is designed to boost the cost-effective, high-energy Zn-I2 battery. Such a configuration concurrently addresses the parasitic reactions on the Zn anode side and the polyiodide shuttle issue afflicting the cathode. Specifically, the Zn2+-cross-linked sodium alginate and carrageenan dual network (Carra-Zn-Alg) is adopted to guide the Zn2+ transport, achieving a dendrite-free morphology on the Zn surface and ensuring long-term stability. For the cathode side, the poly(vinyl alcohol)-strengthened poly(3,4-ethylenedioxythiophene)polystyrenesulfonate hydrogel (PVA-PEDOT) with high conductivity is employed to trap polyiodide and accelerate electron transfer for mitigating the shuttle effect and facilitating I2/I- redox kinetics. Attributing to the asymmetrical architecture with a customized interfacial chemistry, the optimized Zn-I2 cell exhibits a superior Coulombic efficiency of 99.84% with a negligible capacity degradation at 0.1 A g-1 and an enhanced stability of 10 000 cycles at 5 A g-1. The proposed asymmetric hydrogel provides a promising route to simultaneously resolve the distinct challenges encountered by the cathode and anode interfaces in rechargeable batteries.

Elastic Polyurethane as Stress-Redistribution-Adhesive-Layer (SRAL) for Directly Integrated High-Energy-Density Flexible Batteries

The low mechanical reliability and integration failure are key challenges hindering the commercialization of geometrically flexible batteries. This work proposes that the failure of directly integrating flexible batteries using traditional rigid adhesives is primarily due to the mismatch between the generated stress at the adhesive/substrate interface, and the maximum allowable stress. Accordingly, a stress redistribution adhesive layer (SRAL) strategy is conceived by using elastic adhesive to redistribute the generated stress. The function mechanism of the SRAL strategy is confirmed by theoretical finite element analysis. Experimentally, a polyurethane (PU) type elastic adhesive (with maximum strain of 1425%) is synthesized and used as the SRAL to integrate rigid cells on different flexible substrates to fabricate directly integrated flexible battery with robust output under various harsh environments, such as stretching, twisting, and even bending in water. The SRAL strategy is expected to be generally applicable in various flexible devices that involve the integration of rigid components onto flexible substrates.

Tackling the Challenges of Aqueous Zn-Ion Batteries via Polymer-Derived Strategies

Zn-ion batteries (ZIBs) have gathered unprecedented interest recently benefiting from their intrinsic safety, affordability, and environmental benignity. Nevertheless, their practical implementation is hampered by low rate performance, inferior Zn2+ diffusion kinetics, and undesired parasitic reactions. Innovative solutions are put forth to address these issues by optimizing the electrodes, separators, electrolytes, and interfaces. Remarkably, polymers with inherent properties of low-density, high processability, structural flexibility, and superior stability show great promising in tackling the challenges. Herein, the recent progress in the synthesis and customization of functional polymers in aqueous ZIBs is outlined. The recent implementations of polymers into each component are summarized, with a focus on the inherent mechanisms underlying their unique functions. The challenges of incorporating polymers into practical ZIBs are also discussed and possible solutions to circumvent them are proposed. It is hoped that such a deep analysis could accelerate the design of polymer-derived approaches to boost the performance of ZIBs and other aqueous battery systems as they share similarities in many aspects.

A lava-inspired proteolytic enzyme therapy on cancer with a PEG-based hydrogel enhances tumor distribution and penetration of liposomes

The enhanced permeability and retention (EPR) effect has become the guiding principle for nanomedicine against cancer for a long time. However, several biological barriers severely resist therapeutic agents' penetration and retention into the deep tumor tissues, resulting in poor EPR effect and high tumor mortality. Inspired by lava, we proposed a proteolytic enzyme therapy to improve the tumor distribution and penetration of nanomedicine. A trypsin-crosslinked hydrogel (Trypsin@PSA Gel) was developed to maintain trypsin's activity. The hydrogel postponed trypsin's self-degradation and sustained the release. Trypsin promoted the cellular uptake of nanoformulations in breast cancer cells, enhanced the penetration through endothelial cells, and degraded total and membrane proteins. Proteomic analysis reveals that trypsin affected ECM components and down-regulated multiple pathways associated with cancer progression. Intratumoral injection of Trypsin@PSA Gel significantly increased the distribution of liposomes in tumors and reduced tumor vasculature. Combination treatment with intravenous injection of gambogic acid-loaded liposomes and intratumoral injection of Trypsin@PSA Gel inhibited tumor growth. The current study provides one of the first investigations into the enhanced tumor distribution of liposomes induced by a novel proteolytic enzyme therapy.

Tough Hydro-Aerogels with Cation Specificity Enabled Ultra-High Stability for Multifunctional Sensing and Quasi-Solid-State Electrolyte Applications

The anion-specific effects of the salting-in and salting-out phenomena are extensively observed in hydrogels, whereas the cation specificity of hydrogels is rarely reported. Herein, a multi-step strategy including borax pre-gelation, saline soaking, freeze-drying, and rehydrating is developed to fabricate polyvinyl alcohol gels with cation specificity, exhibiting the specific ordering of effects on the mechanical properties of gels as Ca2+ > Li+ > Mg2+ >> Fe3+ > Cu2+ >> Co2+ ≈ Ni2+ ≈ Zn2+. The multiple effects of the fabrication strategy, including the electrostatic repulsion among cations, skeleton support function of graphene oxide nanosheets, and water absorption and retention of ions, endow the gels with the dual characteristics of hydrogels and aerogels (i.e., hydro-aerogels). The hydro-aerogels prepared with the cationic salting-out effect display attractive pressure sensing performance with excellent stability over 90 days and enable continuous monitoring of ambient humidity in real-time and effective work in seawater to detect various parameters (e.g., depth, salinity, and temperature). The hydro-aerogels prepared without borax pretreatment or using the cationic salting-in effect can serve as quasi-solid-state electrolytes in supercapacitors, with 99.59% capacitance retention after 10 000 cycles. This study realizes cation specificity in hydrogels and designs multifunctional hydro-aerogels for promising applications in various fields.

In Situ Polymerization of Hydrogel Electrolyte on Electrodes Enabling the Flexible All-Hydrogel Supercapacitors with Low-Temperature Adaptability

All-hydrogel supercapacitors are emerging as promising power sources for next-generation wearable electronics due to their intrinsic mechanical flexibility, eco-friendliness, and enhanced safety. However, the insufficient interfacial adhesion between the electrode and electrolyte and the frozen hydrogel matrices at subzero temperatures largely limit the practical applications of all-hydrogel supercapacitors. Here, an all-hydrogel supercapacitor is reported with robust interfacial contact and anti-freezing property, fabricated by in situ polymerizing hydrogel electrolyte onto hydrogel electrodes. The robust interfacial adhesion is developed by the synergistic effect of a tough hydrogel matrix and topological entanglements. Meanwhile, the incorporation of zinc chloride (ZnCl2) in the hydrogel electrolyte prevents the freezing of water solvents and endows the all-hydrogel supercapacitor with mechanical flexibility and fatigue resistance across a wide temperature range of 20 °C to -60 °C. Such all-hydrogel supercapacitor demonstrates satisfactory low-temperature electrochemical performance, delivering a high energy density of 11 mWh cm-2 and excellent cycling stability with a capacitance retention of 90% over 10000 cycles at -40 °C. Notably, the fabricated all-hydrogel supercapacitor can endure dynamic deformations and operate well under 2000 tension cycles even at -40 °C, without experiencing delamination and electrochemical failure. This work offers a promising strategy for flexible energy storage devices with low-temperature adaptability.

Validating Operating Stability and Biocompatibility Toward Safer Zinc-Based Batteries

Wearable and implantable electronics are standing at the frontiers of science and technology, driven by the increasing demands from modernized lifestyles. Zinc-based batteries (ZBs) are regarded as ideal energy suppliers for these biocompatible electronics, but the corresponding biocompatibility validation is still in the initial stage. Meanwhile, complicated working conditions and some extreme electrolyte environments raise strict challenges, leaving less choices for safe ZBs. Toward higher operating stability and biocompatibility, this work proposes a hydrogel electrolyte featuring the moisture maintaining ability and a robust interface, which could further provide a milder environment for Zn-MnO2 batteries and Zn-air batteries. The cytotoxicity and tissue injury of batteries are evaluated with human cell lines and battery implantations on the animal models, which demonstrate the high biocompatibility of ZBs, while preliminary wearable devices implementation further verifies their operating stability. This work may provide a pathway for developing and validating biocompatible ZBs, contributing to their future practical employment in relevant fields.

Digital Light Processing 4D Printing of Poloxamer Micelles for Facile Fabrication of Multifunctional Biocompatible Hydrogels as Tailored Wearable Sensors

The lack of both digital light processing (DLP) compatible and biocompatible photopolymers, along with inappropriate material properties required for wearable sensor applications, substantially hinders the employment of DLP 3D printing in the fabrication of multifunctional hydrogels. Herein, we discovered and implemented a photoreactive poloxamer derivative, Pluronic F-127 diacrylate, which overcomes these limitations and is optimized to achieve DLP 3D printed micelle-based hydrogels with high structural complexity, resolution, and precision. In addition, the dehydrated hydrogels exhibit a shape-memory effect and are conformally attached to the geometry of the detection point after rehydration, which implies the 4D printing characteristic of the fabrication process and is beneficial for the storage and application of the device. The excellent cytocompatibility and in vivo biocompatibility further strengthen the potential application of the poloxamer micelle-based hydrogels as a platform for multifunctional wearable systems. After processing them with a lithium chloride (LiCl) solution, multifunctional conductive ionic hydrogels with antifreezing and antiswelling properties along with good transparency and water retention are easily prepared. As capacitive flexible sensors, the DLP 3D printed micelle-based hydrogel devices exhibit excellent sensitivity, cycling stability, and durability in detecting multimodal deformations. Moreover, the DLP 3D printed conductive hydrogels are successfully applied as real-time human motion and tactile sensors with satisfactory sensing performances even in a -20 °C low-temperature environment.

Minimally invasive power sources for implantable electronics

As implantable medical electronics (IMEs) developed for healthcare monitoring and biomedical therapy are extensively explored and deployed clinically, the demand for non-invasive implantable biomedical electronics is rapidly surging. Current rigid and bulky implantable microelectronic power sources are prone to immune rejection and incision, or cannot provide enough energy for long-term use, which greatly limits the development of miniaturized implantable medical devices. Herein, a comprehensive review of the historical development of IMEs and the applicable miniaturized power sources along with their advantages and limitations is given. Despite recent advances in microfabrication techniques, biocompatible materials have facilitated the development of IMEs system toward non-invasive, ultra-flexible, bioresorbable, wireless and multifunctional, progress in the development of minimally invasive power sources in implantable systems has remained limited. Here three promising minimally invasive power sources summarized, including energy storage devices (biodegradable primary batteries, rechargeable batteries and supercapacitors), human body energy harvesters (nanogenerators and biofuel cells) and wireless power transfer (far-field radiofrequency radiation, near-field wireless power transfer, ultrasonic and photovoltaic power transfer). The energy storage and energy harvesting mechanism, configurational design, material selection, output power and in vivo applications are also discussed. It is expected to give a comprehensive understanding of the minimally invasive power sources driven IMEs system for painless health monitoring and biomedical therapy with long-term stable functions.

A soft implantable energy supply system that integrates wireless charging and biodegradable Zn-ion hybrid supercapacitors

The advent of implantable bioelectronic devices offers prospective solutions toward health monitoring and disease diagnosis and treatments. However, advances in power modules have lagged far behind the tissue-integrated sensor nodes and circuit units. Here, we report a soft implantable power system that monolithically integrates wireless energy transmission and storage modules. The energy storage unit comprises biodegradable Zn-ion hybrid supercapacitors that use molybdenum sulfide (MoS2) nanosheets as cathode, ion-crosslinked alginate gel as electrolyte, and zinc foil as anode, achieving high capacitance (93.5 mF cm-2) and output voltage (1.3 V). Systematic investigations have been conducted to elucidate the charge storage mechanism of the supercapacitor and to assess the biodegradability and biocompatibility of the materials. Furthermore, the wirelessly transmitted energy can not only supply power directly to applications but also charge supercapacitors to ensure a constant, reliable power output. Its power supply capabilities have also been successfully demonstrated for controlled drug delivery.

A Mitochondrion-Inspired Magnesium-Oxygen Biobattery with High Energy Density In Vivo

Implantable batteries are urgently needed as a power source to meet the demands of the next generation of biomedical electronic devices. However, existing implantable batteries suffer from unsatisfactory energy density, hindering the miniaturization of these devices. Here, a mitochondrion-inspired magnesium-oxygen biobattery that achieves both high energy density and biocompatibility in vivo is reported. The resulting biobattery exhibits a recorded energy density of 2517 Wh L-1 /1491 Wh kg-1 based on the total volume/mass of the device in vivo, which is ≈2.5 times higher than the current state-of-the-art, and can adapt to different environments for stable discharges. The volume of the magnesium-oxygen biobattery can be as thin as 0.015 mm3 and can be scaled up to 400 times larger without reducing the energy density. Additionally, it shows a stable biobattery/tissue interface, significantly reducing foreign body reactions. This work presents an effective strategy for the development of high-performance implantable batteries.

Hetero Nucleus Growth Stabilizing Zinc Anode for High-Biosecurity Zinc-Ion Batteries

Biocompatible devices are widely employed in modernized lives and medical fields in the forms of wearable and implantable devices, raising higher requirements on the battery biocompatibility, high safety, low cost, and excellent electrochemical performance, which become the evaluation criteria toward developing feasible biocompatible batteries. Herein, through conducting the battery implantation tests and leakage scene simulations on New Zealand rabbits, zinc sulfate electrolyte is proved to exhibit higher biosecurity and turns out to be one of the ideal zinc salts for biocompatible zinc-ion batteries (ZIBs). Furthermore, in order to mitigate the notorious dendrite growth and hydrogen evolution in mildly acidic electrolyte as well as improve their operating stability, Sn hetero nucleus is introduced to stabilize the zinc anode, which not only facilitates the planar zinc deposition, but also contributes to higher hydrogen evolution overpotential. Finally, a long lifetime of 1500 h for the symmetrical cell, the specific capacity of 150 mAh g-1 under 0.5 A g-1 for the Zn-MnO2 battery and 212 mAh g-1 under 5 A g-1 for the Zn-NH4V4O10 battery are obtained. This work may provide unique perspectives on biocompatible ZIBs toward the biosecurity of their cell components.

A biocompatible electrolyte enables highly reversible Zn anode for zinc ion battery

Progress towards the integration of technology into living organisms requires power devices that are biocompatible and mechanically flexible. Aqueous zinc ion batteries that use hydrogel biomaterials as electrolytes have emerged as a potential solution that operates within biological constraints; however, most of these batteries feature inferior electrochemical properties. Here, we propose a biocompatible hydrogel electrolyte by utilising hyaluronic acid, which contains ample hydrophilic functional groups. The gel-based electrolyte offers excellent anti-corrosion ability for zinc anodes and regulates zinc nucleation/growth. Also, the gel electrolyte provides high battery performance, including a 99.71% Coulombic efficiency, over 5500 hours of long-term stability, improved cycle life of 250 hours under a high zinc utilization rate of 80%, and high biocompatibility. Importantly, the Zn//LiMn2O4 pouch cell exhibits 82% capacity retention after 1000 cycles at 3 C. This work presents a promising gel chemistry that controls zinc behaviour, offering great potential in biocompatible energy-related applications and beyond.

Tissue-Matchable and Implantable Batteries Toward Biomedical Applications

Implantable electronic devices can realize real-time and reliable health monitoring, diagnosis, and treatment of human body, which are expected to overcome important bottlenecks in the biomedical field. However, the commonly used energy supply devices for them are implantable batteries based on conventional rigid device design with toxic components, which both mechanically and biologically mismatch soft biological tissues. Therefore, the development of highly soft, safe, and implantable tissue-matchable flexible batteries is of great significance and urgency for implantable bioelectronics. In this work, the recent advances of tissue-matchable and implantable flexible batteries are overviewed, focusing on the design strategies of electrodes/batteries and their biomedical applications. The mechanical flexibility, biocompatibility, and electrochemical performance in vitro and in vivo of these flexible electrodes/batteries are then discussed. Finally, perspectives are provided on the current challenges and possible directions of this field in the future.

Single-Ion-Conducting Hydrogel Electrolytes Based on Slide-Ring Pseudo-Polyrotaxane for Ultralong-Cycling Flexible Zinc-Ion Batteries

Flexible zinc-ion batteries (ZIBs) with high capacity and long cycle stability are essential for wearable electronic devices. Hydrogel electrolytes have been developed to provide ion-transfer channels while maintaining the integrity of ZIBs under mechanical strain. However, hydrogel matrices are typically swollen with aqueous salt solutions to increase ionic conductivity, which can hinder intimate contact with electrodes and reduce mechanical properties. To address this, a single-Zn-ion-conducting hydrogel electrolyte (SIHE) is developed by integrating polyacrylamide network and pseudo-polyrotaxane structure. The SIHE exhibits a high Zn2+ transference number of 0.923 and a high ionic conductivity of 22.4 mS cm-1 at room temperature. Symmetric batteries with SIHE demonstrate stable Zn plating/stripping performance for over 160 h, with a homogenous and smooth Zn deposition layer. Full cells with La-V2 O5 cathodes exhibit a high capacity of 439 mA h g-1 at 0.1 A g-1 and excellent capacity retention of 90.2% after 3500 cycles at 5 A g-1 . Moreover, the flexible ZIBs display stable electrochemical performance under harsh conditions, such as bending, cutting, puncturing, and soaking. This work provides a simple design strategy for single-ion-conducting hydrogel electrolytes, which could pave the way for long-life aqueous batteries.

Granular Ionogel Particle Inks for 3D Printed Tough and Stretchable Ionotronics

Ionogels have garnered great attention as promising soft conducting materials for the fabrication of flexible energy storage devices, soft actuators, and ionotronics. However, the leakage of the ionic liquids, weak mechanical strength, and poor manufacturability have greatly limited their reliability and applications. Here, we propose a new ionogel synthesis strategy by utilizing granular zwitterionic microparticles to stabilize ionic liquids. The ionic liquids swell the microparticles and physically crosslink microparticles via either electronic interaction or hydrogen bonding. Further introducing a photocurable acrylic monomer enables the fabrication of double-network (DN) ionogels with high stretchability (>600%) and ultrahigh toughness (fracture energy > 10 kJ/m2). The synthesized ionogels exhibit a wide working temperature of -60 to 90 °C. By tuning the crosslinking density of microparticles and physical crosslinking strength of ionogels, we synthesize DN ionogel inks and print them into three-dimensional (3D) motifs. Several ionogel-based ionotronics are 3D printed as demonstrations, including strain gauges, humidity sensors, and ionic skins made of capacitive touch sensor arrays. Via covalently linking ionogels with silicone elastomers, we integrate the ionogel sensors onto pneumatic soft actuators and demonstrate their capacities in sensing large deformation. As our last demonstration, multimaterial direct ink writing is harnessed to fabricate highly stretchable and durable alternating-current electroluminescent devices with arbitrary structures. Our printable granular ionogel ink represents a versatile platform for the future manufacturing of ionotronics.

Scalable-produced 3D elastic thermoelectric network for body heat harvesting

Flexible thermoelectric generators can power wearable electronics by harvesting body heat. However, existing thermoelectric materials rarely realize high flexibility and output properties simultaneously. Here we present a facile, cost-effective, and scalable two-step impregnation method for fabricating a three-dimensional thermoelectric network with excellent elasticity and superior thermoelectric performance. The reticular construction endows this material with ultra-light weight (0.28 g cm^-3), ultra-low thermal conductivity (0.04 W m^-1 K^-1), moderate softness (0.03 MPa), and high elongation (>100%). The obtained network-based flexible thermoelectric generator achieves a pretty high output power of 4 μW cm^-2, even comparable to state-of-the-art bulk-based flexible thermoelectric generators.

Hydrogel-Based Flexible Electronics

Flexible electronics is an emerging field of research involving multiple disciplines, which include but not limited to physics, chemistry, materials science, electronic engineering, and biology. However, the broad applications of flexible electronics are still restricted due to several limitations, including high Young's modulus, poor biocompatibility, and poor responsiveness. Innovative materials aiming for overcoming these drawbacks and boost its practical application is highly desirable. Hydrogel is a class of 3D crosslinked hydrated polymer networks, and its exceptional material properties render it as a promising candidate for the next generation of flexible electronics. Here, the latest methods of synthesizing advanced functional hydrogels and the state-of-art applications of hydrogel-based flexible electronics in various fields are reviewed. More importantly, the correlation between properties of the hydrogel and device performance is discussed here, to have better understanding of the development of flexible electronics by using environmentally responsive hydrogels. Last, perspectives on the current challenges and future directions in the development of hydrogel-based multifunctional flexible electronics are provided.

Technology Roadmap for Flexible Sensors

Humans rely increasingly on sensors to address grand challenges and to improve quality of life in the era of digitalization and big data. For ubiquitous sensing, flexible sensors are developed to overcome the limitations of conventional rigid counterparts. Despite rapid advancement in bench-side research over the last decade, the market adoption of flexible sensors remains limited. To ease and to expedite their deployment, here, we identify bottlenecks hindering the maturation of flexible sensors and propose promising solutions. We first analyze challenges in achieving satisfactory sensing performance for real-world applications and then summarize issues in compatible sensor-biology interfaces, followed by brief discussions on powering and connecting sensor networks. Issues en route to commercialization and for sustainable growth of the sector are also analyzed, highlighting environmental concerns and emphasizing nontechnical issues such as business, regulatory, and ethical considerations. Additionally, we look at future intelligent flexible sensors. In proposing a comprehensive roadmap, we hope to steer research efforts towards common goals and to guide coordinated development strategies from disparate communities. Through such collaborative efforts, scientific breakthroughs can be made sooner and capitalized for the betterment of humanity.

A Full-Device Autonomous Self-Healing Stretchable Soft Battery from Self-Bonded Eutectogels

Next-generation energy storage devices should be soft, stretchable, and self-healable. Previously reported self-healable batteries mostly possess limited stretchability and rely on healable electrodes or electrolytes rather than achieving full-device self-healability. Herein, an all-component self-bonding strategy is reported to obtain an all-eutectogel soft battery (AESB) that simultaneously achieves full-cell autonomous self-healability and omnidirectional intrinsic stretchability (>1000% areal strain) over a broad temperature range (-20~60 °C). Without requiring any external stimulus, the five-layered soft battery can efficiently recover both its mechanical and electrochemical performance at full-cell level. The developed AESB can be easily configured into various 3D architectures with highly interfacial compatible eutectogel electrodes, electrolyte, and substrate, presenting an excellent opportunity for the development of embodied energy technologies. The present work provides a general and user-friendly soft electronic material platform for fabricating a variety of intrinsic self-healing stretchable multi-layered electronics, which are promising beyond the field of energy storage, such as displays, sensors, circuits, and soft robots.

Tissue-like Conductive Ti3C2/Sodium Alginate Hybrid Hydrogel for Electrochemical Sensing

Endowed with a soft and conductive feature, hydrogels have been widely used as interface materials in bioelectronics to fulfill mechanical matching and bidirectional exchange between electronic platforms and living samples. Despite their ionic conductivity, the lack of electron mobility has limited their further applications in biosensing, especially in the field of electrochemical sensing. Here, we propose a Ti₃C₂/sodium alginate (SA) hybrid hydrogel with not only a tissue-like mechanical strength (down to 80 kPa) but also a combined exchange interface for ions and electrons, realizing both mechanical and electrical coupling toward biological tissues. Due to the shared gelation tendency with cations, the Ti₃C₂ sheets and SA chains can be easily in situ coassembled through a one-step electrogelation method, making the hybrid hydrogel a well-suited interface layer for device functionalization. In addition, the typical two-dimensional (2D) structure and the abundant active terminals of Ti₃C₂ have endowed the Ti₃C₂/SA with a massive loading capacity toward catalytic nanoparticles. For example, the Prussian Blue (PB)-loaded Ti₃C₂/SA hybrid hydrogel exhibited an excellent electrochemical performance (sensitivity: 600 nA μM^-1 cm^-2; LOD: 12 nM) toward hydrogen peroxide sensing in tissue fluids, illustrating a promising application potentiality of the hybrid hydrogel in biochemical detection at tissue interfaces.

A pH-Sensitive, Stretchable, Antibacterial Artificial Tongue Based on MXene Cross-Linked Ionogel

Dehydration has always been a confusing problem for a hydrogel exposed to air, which restricts its application in practical detection. While an ionogel with unique properties can lock water molecules efficiently due to its low vapor pressure, the design and development of an ionogel with excellent water-locking properties and stability to achieve satisfactory detection are thus highly desirable. In this work, a pH-sensitive, stretchable, antibacterial, and stable ionogel artificial tongue was fabricated through dual cross-linking. The artificial tongue consisted of MXene as a cross-linking agent, phenol red as an indicator, gelatin, N-(2-hydroxyethyl) acrylamide, and 1-butyl-3-methylimidazolium chloride as the three-dimensional polymer network. A small quantity of MXene was used as a cross-linker the first time to promote the initiator in the system to generate free radicals, accelerating the reaction process and the multilevel linkage among the polymers. Meanwhile, the indicator phenol red was introduced into the ionogel successfully for the first time, showing great stability in 5 weeks. After evaluation by the Brand-Altman analysis, it was found that the method of pH measurement using ionogels had good consistency with the pH meter measurement method. Additionally, the prepared ionogel presented excellent water retention, mechanical stretchability, antibacterial property, and stability, as well as good test results in the test of artificial simulated saliva, demonstrating great potential in clinical applications.

Hydrogels Enable Future Smart Batteries

The growing trend of intelligent devices ranging from wearables and soft robots to artificial intelligence has set a high demand for smart batteries. Hydrogels provide opportunities for smart batteries to self-adjust their functions according to the operation conditions. Despite the progress in hydrogel-based smart batteries, a gap remains between the designable functions of diverse hydrogels and the expected performance of batteries. In this Perspective, we first briefly introduce the fundamentals of hydrogels, including formation, structure, and characteristics of the internal water and ions. Batteries that operate under unusual mechanical and temperature conditions enabled by hydrogels are highlighted. Challenges and opportunities for further development of hydrogels are outlined to propose future research in smart batteries toward all-climate power sources and intelligent wearables.

Polymerization-Driven Self-Wrinkling on a Frozen Hydrogel Surface toward Ultra-Stretchable Polypyrrole-Based Supercapacitors

The construction of ultra-stretchable and smart supercapacitors with a large deformation-tolerance range and highly efficient self-healability is fully desired for next-generation wearable electronics. Herein, a sandwich-structured self-wrinkling hydrogel film (SSHF) is fabricated by freezing-constrained polymerization-driven self-wrinkling. Polypyrrole layers are first polymerized on a frozen pre-stretching hydrogel surface and subsequently self-wrinkled upon releasing the pre-strain. The SSHF with two polypyrrole electrode layers sandwiched with a hydrogel electrolytic layer is finally achieved by cutting four edges, and the all-in-one integrated structure creatively avoids the delamination between the electrodes and the electrolyte. The as-obtained SSHF can be directly used as an integrated all-in-one supercapacitor demonstrating high specific capacitance (79.5 F g^-1 at 0.5 A g^-1), large stretchability (>500%), and reliable room temperature self-healability. The freezing-constrained polymerization-driven self-wrinkling strategy might provide a unique self-wrinkling procedure to fabricate self-healable conducting polymer-based hydrogels for ultra-stretchable smart supercapacitors.

Highly Resilient Dual-Crosslinked Hydrogel Adhesives Based on a Dopamine-Modified Crosslinker

Hydrogels are promising material for wound dressing and tissue engineering. However, owing to their low tissue adhesion in a moist environment and lack of flexibility, hydrogels are still not widely applied in movable parts, such as joints. Herein, we report a dual-crosslinked hydrogel adhesive using a dopamine-modified and acrylate-terminated crosslinker, tri(ethylene glycol) diacrylate-dopamine crosslinker (TDC). The covalent crosslinking was formed by photopolymerization between acrylic acid (AA) and TDC, and the noncovalent crosslinking was formed by intermolecular dopamine-dopamine and dopamine-AA interactions. Our resultant hydrogel demonstrated strong tissue adhesion in a moist environment (approximately 71 kPa) and high mechanical resilience (approximately 94%) with immediate recovery at a 200% strain rate. Moreover, it accelerated wound healing upon dressing the wound site properly. Our study provides the potential for advanced polymer synthesis by introducing a functional crosslinking agent.

Biocompatible Conductive Hydrogels: Applications in the Field of Biomedicine

The impact of COVID-19 has rendered medical technology an important factor to maintain social stability and economic increase, where biomedicine has experienced rapid development and played a crucial part in fighting off the pandemic. Conductive hydrogels (CHs) are three-dimensional (3D) structured gels with excellent electrical conductivity and biocompatibility, which are very suitable for biomedical applications. CHs can mimic innate tissue's physical, chemical, and biological properties, which allows them to provide environmental conditions and structural stability for cell growth and serve as efficient delivery substrates for bioactive molecules. The customizability of CHs also allows additional functionality to be designed for different requirements in biomedical applications. This review introduces the basic functional characteristics and materials for preparing CHs and elaborates on their synthetic techniques. The development and applications of CHs in the field of biomedicine are highlighted, including regenerative medicine, artificial organs, biosensors, drug delivery systems, and some other application scenarios. Finally, this review discusses the future applications of CHs in the field of biomedicine. In summary, the current design and development of CHs extend their prospects for functioning as an intelligent and complex system in diverse biomedical applications.