Silicon nanograss based impedance biosensor for label free detection of rare metastatic cells among primary cancerous colon cells, suitable for more accurate cancer staging

The Impact of Microelectrode Pattern on the Sensitivity of Tracing Environmental CO2 Deficiency in Cellular Metabolism by a New Design of Electrochemical Biosensor

Here, two different electrode patterns are described as cyclic voltammetry (CV) biosensors to detect the effect of a hypo CO2 condition (for 6 h) in ambient on cellular secretion. The cells were selected from breast cancer and endothelial standard lines. Changes in CV peaks of the secretions were recorded by the modified pattern whereby increasing the interactive surface with homogenous electric paths was considered by simulation before fabrication. The results of the simulation and experimental procedures showed a meaningful correlation between hypo CO2 samples and the occurrence of CV oxidative peaks at about 0.07 V and reductive peaks at approximately -0.22 V in the modified biosensor in all cell lines, while no apoptosis was found in any of the control and hypo CO2 samples. This observation could not be related to the lack of H+ (alkaline pH induction) in the media solution as such peaks were not observed in the pure cell culture medium but had been maintained in the hypo CO2 ambient. This approach could be used as a cell-free sensor to monitor ambient shocks. This may not induce apoptosis but may be vital in the proliferation and protein expression of the cells, such as the hypo CO2 ambient. The sensor is not disposable in use and showed repeatable responses after rinsing.

Predictive Cell Culture Time Evolution Based on Electric Models

Obtaining cell concentration measurements from a culture assay by using bioimpedance is a very useful method that can be used to translate impedances to cell concentration values. The purpose of this study was to find a method to obtain the cell concentration values of a given cell culture assay in real time by using an oscillator as the measurement circuit. From a basic cell-electrode model, enhanced models of a cell culture immersed in a saline solution (culture medium) were derived. These models were used as part of a fitting routine to estimate the cell concentration in a cell culture in real time by using the oscillation frequency and amplitude delivered by the measurement circuits proposed by previous authors. Using real experimental data (the frequency and amplitude of oscillations) that were obtained by connecting the cell culture to an oscillator as the load, the fitting routine was simulated, and real-time data of the cell concentration were obtained. These results were compared to concentration data that were obtained by using traditional optical methods for counting. In addition, the error that we obtained was divided and analyzed in two parts: the first part of the experiment (when the few cells were adapting to the culture medium) and the second part of the experiment (when the cells exponentially grew until they completely covered the well). Low error values were obtained during the growth phase of the cell culture (the relevant phase); therefore, the results obtained were considered promising and show that the fitting routine is valid and that the cell concentration can be measured in real time by using an oscillator.

High-Frequency (30 MHz-6 GHz) Breast Tissue Characterization Stabilized by Suction Force for Intraoperative Tumor Margin Assessment

A gigahertz (GHz) range antenna formed by a coaxial probe has been applied for sensing cancerous breast lesions in the scanning platform with the assistance of a suction tube. The sensor structure was a planar central layer and a metallic sheath of size of 3 cm² connected to a network analyzer (keySight FieldFox N9918A) with operational bandwidth up to 26.5 GHz. Cancer tumor cells have significantly higher water content (as a dipolar molecule) than normal breast cells, changing their polarization responses and dielectric losses to incoming GHz-based stimulation. Principal component analysis named S₁₁, related to the dispersion ratio of the input signal, is used as a parameter to identify malignant tumor cells in a mouse model (in vivo) and tumor specimens of breast cancer patients (in vitro) (both central and marginal parts). The results showed that S₁₁ values in the frequency range from 5 to 6 GHz were significantly higher in cancer-involved breast lesions. Histopathological analysis was the gold standard for achieving the S₁₁ calibration to distinguish normal from cancerous lesions. Our calibration on tumor specimens presented 82% positive predictive value (PPV), 100% negative predictive value (NPV), and 86% accuracy. Our goal is to apply this system as an in vivo non-invasive tumor margin scanner after further investigations in the future.

3D-Printed Sensors and Actuators in Cell Culture and Tissue Engineering: Framework and Research Challenges

Three-dimensional printing technologies have been recently proposed to monitor cell cultures and implement cell bioreactors for different biological applications. In tissue engineering, the control of tissue formation is crucial to form tissue constructs of clinical relevance, and 3D printing technologies can also play an important role for this purpose. In this work, we study 3D-printed sensors that have been recently used in cell culture and tissue engineering applications in biological laboratories, with a special focus on the technique of electrical impedance spectroscopy. Furthermore, we study new 3D-printed actuators used for the stimulation of stem cells cultures, which is of high importance in the process of tissue formation and regenerative medicine. Key challenges and open issues, such as the use of 3D printing techniques in implantable devices for regenerative medicine, are also discussed.

Development of peptide biosensor for the detection of dengue fever biomarker, nonstructural 1

Dengue virus (DENV) nonstructural 1 (NS1) protein is a specific and sensitive biomarker for the diagnosis of dengue. In this study, an efficient electrochemical biosensor that uses chemically modified affinity peptides was developed for the detection of dengue virus NS1. A series of amino acid-substituted synthetic peptides was rationally designed, chemically synthesized and covalently immobilized to a gold sensor surface. The sensor performance was monitored via square wave voltammetry (SWV) and electrochemical impedance spectroscopy (EIS). Potential affinity peptides specific for NS1 were chosen according to the dynamic current decrease in SWV experiments. Using circular dichroism, the molar ellipticity of peptides (DGV BP1–BP5) was determined, indicating that they had a mostly similar in random coil structure, not totally identical. Using SWV, DGV BP1 was selected as a promising recognition peptide and limit of detection for NS1 was found to be 1.49 μg/mL by the 3-sigma rule. DGV BP1 showed good specificity and stability for NS1, with low signal interference. The validation of the sensor to detect NS1 proteins was confirmed with four dengue virus culture broth (from serotype 1 to 4) as proof-of-concept. The detection performance of our sensor incorporating DGV BP1 peptides showed a statistically significant difference. These results indicate that this strategy can potentially be used to detect the dengue virus antigen, NS1, and to diagnosis dengue fever within a miniaturized portable device in point-of-care testing.

Bioelectronics of The Cellular Cytoskeleton: Monitoring Cytoskeletal Conductance Variation for Sensing Drug Resistance

Actin and microtubules form cellular cytoskeletal network, which mediates cell shape, motility and proliferation and are key targets for cancer therapy. Changes in cytoskeletal organization dramatically affect mechanical properties of the cells and correlate with proliferative capacity and invasiveness of cancer cells. Changes in the cytoskeletal network expectedly lead to altered nonmechanical material properties including electrical conductivity as well. Here we applied, for the first time, microtubule and actin based electrical measurement to monitor changes in the electrical properties of breast cancer cells upon administration of anti-tubulin and anti-actin drugs, respectively. Semiconductive behavior of microtubules and conductive behavior of actins presented different bioelectrical responses (in similar frequencies) of the cells treated by anti-tubulin with respect to anti-actin drugs. Doped silicon nanowires were applied as the electrodes due to their enhanced interactive surface and compatibility with electronic fabrication process. We found that treatment with Mebendazole (MBZ), a microtubule destabilizing agent, decreases electrical resistance while treatment with Paclitaxel (PTX), a microtubule stabilizing agent, leads to an increase in electrical resistance. In contrast, actin destabilizing agents, Cytochalasin D (CytD), and actin stabilizing agent, Phalloidin, lead to an increased and decreased electrical resistance, respectively. Our study thus provides proof-of-principle of the usage of determining the electrical function of cytoskeletal compartments in grading of cancer as well as drug resistance assays.

An Empirical-Mathematical Approach for Calibration and Fitting Cell-Electrode Electrical Models in Bioimpedance Tests

This paper proposes a new yet efficient method allowing a significant improvement in the on-line analysis of biological cell growing and evolution. The procedure is based on an empirical-mathematical approach for calibration and fitting of any cell-electrode electrical model. It is valid and can be extrapolated for any type of cellular line used in electrical cell-substrate impedance spectroscopy (ECIS) tests. Parameters of the bioimpedance model, acquired from ECIS experiments, vary for each cell line, which makes obtaining results difficult and—to some extent-renders them inaccurate. We propose a fitting method based on the cell line initial characterization, and carry out subsequent experiments with the same line to approach the percentage of well filling and the cell density (or cell number in the well). To perform our calibration technique, the so-called oscillation-based test (OBT) approach is employed for each cell density. Calibration results are validated by performing other experiments with different concentrations on the same cell line with the same measurement technique. Accordingly, a bioimpedance electrical model of each cell line is determined, which is valid for any further experiment and leading to a more precise electrical model of the electrode-cell system. Furthermore, the model parameters calculated can be also used by any other measurement techniques. Promising experimental outcomes for three different cell-lines have been achieved, supporting the usefulness of this technique.

Tracing the pH dependent activation of autophagy in cancer cells by silicon nanowire-based impedance biosensor

Monitoring the pH dependent behavior of normal and cancer cells by impedimetric biosensor based on Silicon Nanowires (SiNWs) was introduced to diagnose the invasive cancer cells. Autophagy as a biologically activated process in invasive cancer cells during acidosis, protect them from apoptosis in lower pH which presented in our work. As the autophagy is the only activated pathways which can maintain cellular proliferation in acidic media, responses of SiNW-ECIS in acidified cells could be correlated to the probability of autophagy activation in normal or cancer cells. In contrast, cell survival pathway wasn't activated in low-grade cancer cells which resulted in their acidosis. The measured electrical resistance of MCF10, MCF7, and MDA-MB468 cell lines, by SiNW sensor, in normal and acidic media were matched by the biological analyses of their vital functions. Invasive cancer cells exhibited increased electrical resistance in pH 6.5 meanwhile the two other types of the breast cells exhibited sharp (MCF10) and moderate (MCF7) decrease in their resistance. This procedure would be a new trend in microenvironment based cancer investigation.

Monitoring the effect of sonoporation on the cells using electrochemical approach

Sonoporation is applied to enhance the permeability of the cell to bioactive materials by employing the acoustic cavitation of microbubbles. This phenomena would be helpful in molecular biology, delivery of large molecules into the cells and gene therapy. Many methods have been applied to monitor the biological effects and trace of sonoporation on the cells such as scanning/transmission electron microscopy, confocal imaging and flow cytometry. Here, we monitored the effect of sonoporation on the cells using electrochemical method with an integrated three electrode system. Electrochemical responses of stimulated cells, compared to flow cytometry and electron microscopy results, presented different patterns of sonoporation in the cells detectable by cyclic voltammetry. In addition, confocal microscopy from actin stress fibers and young's modulus measured by AFM revealed the correlation of cell mechanics and amount of induced sonopores in the cells. This method could be applied as a new trend in cellular mechanochemical studies.

Bioelectrical impedimetric sensor for single cell analysis based on nanoroughened quartz substrate; suitable for cancer therapeutic purposes

Single cells analysis has been interested in recent decade. Apart from scientific benefits to achieve new biological phenomena in cell study, many diagnostic and therapeutic protocols in non-communicable diseases were introduced by single cell analysis. Moreover, non-invasive methods to maintain the investigated cell for time dependent monitoring has been widely studied because of its importance in some crucial cases such as drug resistance in cancer. Bioelectrical monitoring is one of such methods Although the procedures reported based on electrical probing might not induce cell disruption, indirect connection between recording electrodes and cell membrane (mostly in microfluidic approaches) reduced the quality of response and limited the precision of the results. Here, a bioelectronic sensor for monitoring the effect of anticancer drugs on single breast cancer cells was fabricated based on nano-roughened gold electrodes on a quartz substrate applied direct contacts to cell membrane. Whole of the surface except a microcircle surrounded the sensing region was passivated by overbaked photoresist layer. Cells were dropped on the sensor without the assistance of any micropipette or microfluidic systems and just individual regions for attachment of one cell has been opened on the sensing region arrays. MCF-7 cancer cells were time tracked under the effect of Paclitaxel and Mebendazole anti-tubulin drugs in low and high doses. Inducing non regulated depolymerization and polymerization in tubulin structures of the single cancer cells were monitored by the electrical signals recorded before and after drug treatment. Electrical responses of single cells to their incubation with drugs completely reflected their vitality and biological states which were confirmed by confocal imaging. This is one of the first investigation on bioelectrical monitoring of single cell's resistance to anticancer drugs.

Effects of Hylomecon vernalis ethanol extracts on cell cycle and apoptosis of colon cancer cells

Hylomecon vernalis Maxim. has traditionally been used to promote blood circulation, alleviate pain, dissipate stasis, and reduce swelling. The aim of the present study was to investigate the effect and potential mechanism of H. vernalis Maxim. ethanol extracts (HVMEE) on the growth and apoptosis of human colon cancer HT-29 and SW620 cells. H. vernalis samples were extracted three times with ethanol, dried, and concentrated into powder. The components of HVMEE were investigated using high performance liquid chromatography in tandem with mass spectrometry analysis. MTT assay was used to investigate the effect of HVMEE on viability of human colon cancer HT-29 and SW620 cells. Apoptosis of HT-29 and SW620 cells was evaluated using flow cytometric analysis. Expression levels of apoptosis and cell cycle-related proteins were assessed by western blot. The findings demonstrated that the alkaloid content of HVMEE was as high as 89.67%, and it effectively inhibited viability in HT-29 and SW620 cells, with IC₅₀ values of 0.105±0.022 mg/ml and 0.146±0.013 mg/ml, respectively. In addition, HVMEE induced apoptosis in HT-29 and SW620 cells, by increasing caspase-3, caspase-9 and BCL2 associated X expression, and reducing Bcl-2 expression. The present study suggests that HVMEE has a potential role in the treatment of colorectal cancer.

Microfluidic device for label-free quantitation and distinction of bladder cancer cells from the blood cells using micro machined silicon based electrical approach; suitable in urinalysis assays

This paper introduces an integrated microfluidic chip as a promising tool to measure the concentration of bladder cancer cells (BCC) in urine samples. Silicon microchannels were used as trapping gates for both floated BCC and leukocytes which are found in the urine of patients. By the assistance of the gold electrodes patterned at the bottom of the micro gates, the capacitance of captured cancerous and blood cells were measured. Different membrane capacitance between BCC and leukocyte was the indicative signal for diagnosing the nature of captured cells in a urine like solution. The concentration range of the target that could be detected was about 10 BCCs per one chip. Such response has been achieved without applying any biochemical or florescent markers. Thus, it could be a simple and cheap approach to support cytological and immune-fluorescent assays. The limit of detection was approximately 1 cancerous cell/11 leukocytes in 1ml of the urine like solution. The entire measurement time was less than an hour. Consequently, this electrical microfluidic device promises significant potential in urinalysis.

Rapid biosensing tools for cancer biomarkers

The present review critically discusses the latest developments in the field of smart diagnostic systems for cancer biomarkers. A wide coverage of recent biosensing approaches involving aptamers, enzymes, DNA probes, fluorescent probes, interacting proteins and antibodies in vicinity to transducers such as electrochemical, optical and piezoelectric is presented. Recent advanced developments in biosensing approaches for cancer biomarker owes much credit to functionalized nanomaterials due to their unique opto-electronic properties and enhanced surface to volume ratio. Biosensing methods for a plenty of cancer biomarkers has been summarized emphasizing the key principles involved.

Electrochemical approach for monitoring the effect of anti tubulin drugs on breast cancer cells based on silicon nanograss electrodes

One of the most interested molecular research in the field of cancer detection is the mechanism of drug effect on cancer cells. Translating molecular evidence into electrochemical profiles would open new opportunities in cancer research. In this manner, applying nanostructures with anomalous physical and chemical properties as well as biocompatibility would be a suitable choice for the cell based electrochemical sensing. Silicon based nanostructure are the most interested nanomaterials used in electrochemical biosensors because of their compatibility with electronic fabrication process and well engineering in size and electrical properties. Here we apply silicon nanograss (SiNG) probing electrodes produced by reactive ion etching (RIE) on silicon wafer to electrochemically diagnose the effect of anticancer drugs on breast tumor cells. Paclitaxel (PTX) and mebendazole (MBZ) drugs have been used as polymerizing and depolymerizing agents of microtubules. PTX would perturb the anodic/cathodic responses of the cell-covered biosensor by binding phosphate groups to deformed proteins due to extracellular signal-regulated kinase (ERK(1/2)) pathway. MBZ induces accumulation of Cytochrome C in cytoplasm. Reduction of the mentioned agents in cytosol would change the ionic state of the cells monitored by silicon nanograss working electrodes (SiNGWEs). By extending the contacts with cancer cells, SiNGWEs can detect minor signal transduction and bio recognition events, resulting in precise biosensing. Effects of MBZ and PTX drugs, (with the concentrations of 2 nM and 0.1 nM, respectively) on electrochemical activity of MCF-7 cells are successfully recorded which are corroborated by confocal and flow cytometry assays.

Silicon nanowire based biosensing platform for electrochemical sensing of Mebendazole drug activity on breast cancer cells

Electrochemical approaches have played crucial roles in bio sensing because of their Potential in achieving sensitive, specific and low-cost detection of biomolecules and other bio evidences. Engineering the electrochemical sensing interface with nanomaterials tends to new generations of label-free biosensors with improved performances in terms of sensitive area and response signals. Here we applied Silicon Nanowire (SiNW) array electrodes (in an integrated architecture of working, counter and reference electrodes) grown by low pressure chemical vapor deposition (LPCVD) system with VLS procedure to electrochemically diagnose the presence of breast cancer cells as well as their response to anticancer drugs. Mebendazole (MBZ), has been used as antitubulin drug. It perturbs the anodic/cathodic response of the cell covered biosensor by releasing Cytochrome C in cytoplasm. Reduction of cytochrome C would change the ionic state of the cells monitored by SiNW biosensor. By applying well direct bioelectrical contacts with cancer cells, SiNWs can detect minor signal transduction and bio recognition events, resulting in precise biosensing. Our device detected the trace of MBZ drugs (with the concentration of 2nM) on electrochemical activity MCF-7 cells. Also, experimented biological analysis such as confocal and Flowcytometry assays confirmed the electrochemical results.

Organic Photovoltaics and Bioelectrodes Providing Electrical Stimulation for PC12 Cell Differentiation and Neurite Outgrowth

Current bioelectronic medicines for neurological therapies generally involve treatment with a bioelectronic system comprising a power supply unit and a bioelectrode device. Further integration of wireless and self-powered units is of practical importance for implantable bioelectronics. In this study, we developed biocompatible organic photovoltaics (OPVs) for serving as wireless electrical power supply units that can be operated under illumination with near-infrared (NIR) light, and organic bioelectronic interface (OBEI) electrode devices as neural stimulation electrodes. The OPV/OBEI integrated system is capable to provide electrical stimulation (ES) as a means of enhancing neuron-like PC12 cell differentiation and neurite outgrowth. For the OPV design, we prepared devices incorporating two photoactive material systems--β-carotene/N,N'-dioctyl-3,4,9,10-perylenedicarboximide (β-carotene/PTCDI-C8) and poly(3-hexylthiophene)/phenyl-C61-butyric acid methyl ester (P3HT/PCBM)--that exhibited open circuit voltages of 0.11 and 0.49 V, respectively, under NIR light LED (NLED) illumination. Then, we connected OBEI devices with different electrode gaps, incorporating biocompatible poly(hydroxymethylated-3,4-ethylenedioxythiophene), to OPVs to precisely tailor the direct current electric field conditions during the culturing of PC12 cells. This NIR light-driven OPV/OBEI system could be engineered to provide tunable control over the electric field (from 220 to 980 mV mm(-1)) to promote 64% enhancement in the neurite length, direct the neurite orientation on chips, or both. The OPV/OBEI integrated systems under NIR illumination appear to function as effective power delivery platforms that should meet the requirements for wirelessly offering medical ES to a portion of the nervous system; they might also be a key technology for the development of next-generation implantable bioelectronics.

Nanoelectromechanical Chip (NELMEC) Combination of Nanoelectronics and Microfluidics to Diagnose Epithelial and Mesenchymal Circulating Tumor Cells from Leukocytes

An integrated nano-electromechanical chip (NELMEC) has been developed for the label-free distinguishing of both epithelial and mesenchymal circulating tumor cells (ECTCs and MCTCs, respectively) from white blood cells (WBCs). This nanoelectronic microfluidic chip fabricated by silicon micromachining can trap large single cells (>12 µm) at the opening of the analysis microchannel arrays. The nature of the captured cells is detected using silicon nanograss (SiNG) electrodes patterned at the entrance of the channels. There is an observable difference between the membrane capacitance of the ECTCs and MCTCs and that of WBCs (measured using SiNG electrodes), which is the key indication for our diagnosis. The NELMEC chip not only solves the problem of the size overlap between CTCs and WBCs but also detects MCTCs without the need for any markers or tagging processes, which has been an important problem in previously reported CTC detection systems. The great conductivity of the gold-coated SiNG nanocontacts as well as their safe penetration into the membrane of captured cells, facilitate a precise and direct signal extraction to distinguish the type of captured cell. The results achieved from epithelial (MCF-7) and mesenchymal (MDA-MB231) breast cancer cells circulated in unprocessed blood suggest the significant applications for these diagnostic abilities of NELMEC.

Enhancement of Efficiency of a Solar Cell Fabricated on Black Si Made by Inductively Coupled Plasma-Reactive Ion Etching Process: A Case Study of a n-CdS/p-Si Heterojunction Cell

We show that a significant enhancement of solar cell efficiency can be achieved in cells fabricated on black Si made using inductively coupled plasma-reactive ion etching (ICP-RIE). The ICP-RIE-fabricated black Si results in an array of vertically oriented defect-free Si nanocones (average height ∼150 nm; apex diameter ∼25 nm) exhibiting an average reflectance ≤2% over most of the relevant solar spectral range. The enabling role of the ultralow reflectance of the nanostructured black Si has been demonstrated using a heterojunction solar cell fabricated by depositing a n-type CdS film on p-Si nanocones followed by a transparent conducting coating of Al-doped ZnO (AZO). The fabricated n-CdS/p-Si heterojunction exhibits promising power conversion efficiency close to 3%, up from a mere efficient 0.15% for a similar cell fabricated on a planar Si. The effect of the fabrication process for the black Si on solar cell performance has been investigated through the measurements of carrier lifetime and surface recombination velocity. The accompanying model and simulation analysis shows that the conical structure leads to the effective dielectric constant varying smoothly from the value of the air at the top to the value of Si at the base over the length of the nanocone, leading to a substantial reduction of its reflectance.

Integrated 3D conducting polymer-based bioelectronics for capture and release of circulating tumor cells

Here we develop a novel fabrication approach for producing three-dimensional (3D) conducting polymer-based bioelectronic interfaces (BEIs) that can be integrated on electronic devices for rare circulating tumor cell (CTC) isolation, detection, and collection via an electrically triggered cell released from chips. Based on the chemical oxidative polymerization of carboxylic acid-modified 3,4-ethylenedioxythiophene and modified poly(dimethylsiloxane) (PDMS) transfer printing technology, the high-aspect-ratio structures of poly(3,4-ethylenedioxythiophene) (PEDOT)-based "nanorod" arrays can be fabricated on indium tin oxide (ITO) electrodes when using the Si "microrod" arrays as masters. Furthermore, we integrated the biotinylated poly-(l)-lysine-graft-poly-ethylene-glycol (PLL-g-PEG-biotin) coating with 3D PEDOT-based BEIs for dynamic control of the capture/release performance of CTCs on chips; this combination exhibited an optimal cell-capture yield cells of ∼45 000 cells cm^-2 from EpCAM-positive MCF7 while maintaining resistance from the adhesion of EpCAM-negative HeLa cells at a density of ∼4000 cells cm^-2. By taking advantage of the electrochemical doping/dedoping properties of PEDOT materials, the captured CTCs can be triggered to be electrically released through the desorption phenomena of the PLL-g-PEG-biotin. More than 90% of the captured cells can be released while maintaining very high cell viability. Therefore, it is conceivable that the use of a 3D PEDOT-based BEI platform will meet the requirements for the development of downstream characterization of CTCs, as well as the next generation of bioelectronics for biomedical applications.

A single-cell correlative nanoelectromechanosensing approach to detect cancerous transformation: monitoring the function of F-actin microfilaments in the modulation of the ion channel activity

Cancerous transformation may be dependent on correlation between electrical disruptions in the cell membrane and mechanical disruptions of cytoskeleton structures. Silicon nanotube (SiNT)-based electrical probes, as ultra-accurate signal recorders with subcellular resolution, may create many opportunities for fundamental biological research and biomedical applications. Here, we used this technology to electrically monitor cellular mechanosensing. The SiNT probe was combined with an electrically activated glass micropipette aspiration system to achieve a new cancer diagnostic technique that is based on real-time correlation between mechanical and electrical behaviour of single cells. Our studies demonstrated marked changes in the electrical response following increases in the mechanical aspiration force in healthy cells. In contrast, such responses were extremely weak for malignant cells. Confocal microscopy results showed the impact of actin microfilament remodelling on the reduction of the electrical response for aspirated cancer cells due to the significant role of actin in modulating the ion channel activity in the cell membrane.

Monitoring the spreading stage of lung cells by silicon nanowire electrical cell impedance sensor for cancer detection purposes

We developed a silicon nanowire based electrical cell impedance sensor (SiNW-ECIS) as an instrument that detects cancerous cultured living lung cells by monitoring their spreading state at which the cells stretched and become extended on nanowires. Further current penetration into the extended membrane of malignant cells in respect to normal ones (In the first 6h after cells interaction with surface) are the key mechanism in our diagnosis procedure. The developed device applied to monitor the spreading-induced electrical differences between cancerous and normal lung cells in an integral fashion. Detection was performed so faster than the time required to complete cells mitosis. Morphology and architecture of doped Si nanowires covered microelectrodes observably enhance the contact area between cells and electrodes which support accurate signal recording from stretched cells as indicated by SEM and florescent images.