Highly sensitive fluorescence sensing of zearalenone using a novel aptasensor based on upconverting nanoparticles

Selective extraction of zearalenone from corn steep liquor for raw material of standard substance using polyamide membrane

Zearalenone (ZEN) is one of the most prevalent mycotoxins in corn and its products, which can accumulate in corn steep liquor (CSL) with much higher concentration after deep processing. For ensuring the precision of ZEN analysis in food safety, ZEN standard substance is critical. However, the preparation of standard substance usually needs complex chemical synthesis steps and large amounts of organic solvents consumption. Herein, a facile approach to extract ZEN from CSL for raw material of standard substance using polyamide 66 (PA) membrane as an adsorbent was proposed. Considering the coexistence of aflatoxin B1 (AFB1) and ZEN in CSL, the influence of solvent polarity, membrane pore size, and pH on the selective adsorption of ZEN and AFB1 have been investigated. Under the optimal conditions, the highest adsorption efficiencies of ZEN and AFB1 were 96.5 % and 15.9 %, respectively. A good regeneration and reusability of ZEN from PA membrane could be realized by a desorption process using acetonitrile as eluent. Through various characterizations and density functional theory calculations, it can be concluded that the selective adsorption of ZEN on the PA membrane was dominated by special hydrogen bond and hydrophobic interaction, while the adsorption of AFB1 on the PA membrane was only hydrophobic interaction. Furthermore, PA membrane was used in the extraction of ZEN from contaminated CSL, and the extract rate reached 95.6 %. The present work not only provided a reliable way to high-quality utilization of ZEN contaminated CSL, but also casted new insights into the adsorption mechanism of ZEN.

Ultrasound-Based Micro-/Nanosystems for Biomedical Applications

Due to the intrinsic non-invasive nature, cost-effectiveness, high safety, and real-time capabilities, besides diagnostic imaging, ultrasound as a typical mechanical wave has been extensively developed as a physical tool for versatile biomedical applications. Especially, the prosperity of nanotechnology and nanomedicine invigorates the landscape of ultrasound-based medicine. The unprecedented surge in research enthusiasm and dedicated efforts have led to a mass of multifunctional micro-/nanosystems being applied in ultrasound biomedicine, facilitating precise diagnosis, effective treatment, and personalized theranostics. The effective deployment of versatile ultrasound-based micro-/nanosystems in biomedical applications is rooted in a profound understanding of the relationship among composition, structure, property, bioactivity, application, and performance. In this comprehensive review, we elaborate on the general principles regarding the design, synthesis, functionalization, and optimization of ultrasound-based micro-/nanosystems for abundant biomedical applications. In particular, recent advancements in ultrasound-based micro-/nanosystems for diagnostic imaging are meticulously summarized. Furthermore, we systematically elucidate state-of-the-art studies concerning recent progress in ultrasound-based micro-/nanosystems for therapeutic applications targeting various pathological abnormalities including cancer, bacterial infection, brain diseases, cardiovascular diseases, and metabolic diseases. Finally, we conclude and provide an outlook on this research field with an in-depth discussion of the challenges faced and future developments for further extensive clinical translation and application.

Solvent Regulation Induced Cathode Aggregation-Induced Electrochemiluminescence of Tetraphenylethylene Nanoaggregates for Ultrasensitive Zearalenone Analysis

Zearalenone (ZEN) is an extremely hazardous chemical widely existing in cereals, and its high-sensitivity detection possesses significant significance to human health. Here, the cathodic aggregation-induced electrochemiluminescence (AIECL) performance of tetraphenylethylene nanoaggregates (TPE NAs) was modulated by solvent regulation, based on which an electrochemiluminescence (ECL) aptasensor was constructed for sensitive detection of ZEN. The aggregation state and AIECL of TPE NAs were directly and simply controlled by adjusting the type of organic solvent and the fraction of water, which solved the current shortcomings of low strength and weak stability of the cathode ECL signal for TPE. Impressively, in a tetrahydrofuran-water mixed solution (volume ratio, 6:4), the relative ECL efficiency of TPE NAs reached 16.03%, which was 9.2 times that in pure water conditions, and the maximum ECL spectral wavelength was obviously red-shifted to 617 nm. In addition, "H"-shape DNA structure-mediated dual-catalyzed hairpin self-assembly (H-D-CHA) with higher efficiency by the synergistic effect between the two CHA reactions was utilized to construct a sensitive ECL aptasensor for ZEN analysis with a low detection limit of 0.362 fg/mL. In conclusion, solvent regulation was a simple and efficient method for improving the performance of AIECL materials, and the proposed ECL aptasensor had great potential for ZEN monitoring in food safety.

Fusarium mycotoxins: The major food contaminants

Mycotoxins, which are secondary metabolites produced by toxicogenic fungi, are natural food toxins that cause acute and chronic adverse reactions in humans and animals. The genus Fusarium is one of three major genera of mycotoxin-producing fungi. Trichothecenes, fumonisins, and zearalenone are the major Fusarium mycotoxins that occur worldwide. Fusarium mycotoxins have the potential to infiltrate the human food chain via contamination during crop production and food processing, eventually threatening human health. The occurrence and development of Fusarium mycotoxin contamination will change with climate change, especially with variations in temperature, precipitation, and carbon dioxide concentration. To address these challenges, researchers have built a series of effective models to forecast the occurrence of Fusarium mycotoxins and provide guidance for crop production. Fusarium mycotoxins frequently exist in food products at extremely low levels, thus necessitating the development of highly sensitive and reliable detection techniques. Numerous successful detection methods have been developed to meet the requirements of various situations, and an increasing number of methods are moving toward high-throughput features. Although Fusarium mycotoxins cannot be completely eliminated, numerous agronomic, chemical, physical, and biological methods can lower Fusarium mycotoxin contamination to safe levels during the preharvest and postharvest stages. These theoretical innovations and technological advances have the potential to facilitate the development of comprehensive strategies for effectively managing Fusarium mycotoxin contamination in the future.

Upconversion nanoparticles-modified aptasensors for highly sensitive mycotoxin detection for food quality and safety

Mycotoxins, highly toxic and carcinogenic secondary metabolites produced by certain fungi, pose significant health risks as they contaminate food and feed products globally. Current mycotoxin detection methods have limitations in real-time detection capabilities. Aptasensors, incorporating aptamers as specific recognition elements, are crucial for mycotoxin detection due to their remarkable sensitivity and selectivity in identifying target mycotoxins. The sensitivity of aptasensors can be improved by using upconversion nanoparticles (UCNPs). UCNPs consist of lanthanide ions in ceramic host, and their ladder-like energy levels at f-orbitals have unique photophysical properties, including converting low-energy photons to high-energy emissions by a series of complex processes and offering sharp, low-noise, and sensitive near-infrared to visible detection strategy to enhance the efficacy of aptasensors for novel mycotoxin detection. This article aims to review recent reports on the scope of the potential of UCNPs in mycotoxin detection, focusing on their integration with aptasensors to give readers clear insight. We briefly describe the upconversion photoluminescence (UCPL) mechanism and relevant energy transfer processes influencing UCNP design and optimization. Furthermore, recent studies and advancements in UCNP-based aptasensors will be reviewed. We then discuss the potential impact of UCNP-modified aptasensors on food safety and present an outlook on future directions and challenges in this field. This review article comprehensively explains the current state-of-the-art UCNP-based aptasensors for mycotoxin detection. It provides insights into potential applications by addressing technical and practical challenges for practical implementation.

Electrochemiluminescence immunosensor based on tin dioxide quantum dots and palladium-modified graphene oxide for the detection of zearalenone

Developing low-cost and efficient methods to enhance the electrochemiluminescence (ECL) intensity of luminophores is highly desirable and challenging. Herein, we developed an efficient ECL system based on palladium-modified graphene oxide as a substrate and tin dioxide quantum dot-modified spike-like gold-silver alloy as an immunoprobe. Specifically, palladium-modified graphene oxide was rationally selected as the sensor substrate for the attachment of zearalenone antigens while facilitating the amplification of the ECL signal through enhanced electron transfer efficiency. A spike-like gold-silver alloy modified with tin dioxide quantum dots was attached to the zearalenone antibody as an immunoprobe, and the sensor exhibited remarkable sensitivity due to the exceptional ECL performance of the quantum dots. To demonstrate the practical feasibility of the principle, zearalenone levels were detected in actual samples of maize and pig urine, and the sensor showed a broad linear range (0.0005-500 ng mL-1) and low detection limit (0.16 pg mL-1) in the high-sensitivity detection of Zearalenone. Overall, this work first reports the construction of a highly sensitive ECL immunosensor for the detection of zearalenone using a protruding gold-silver alloy modified with tin dioxide as an immunoprobe and a palladium modified graphene oxide as a substrate. It provides a novel approach for the detection of small molecule toxin-like substances.

Recent advances in nucleic acid signal amplification-based aptasensors for sensing mycotoxins

Mycotoxin contamination in food products may cause serious health hazards and economic losses. The effective control and accurate detection of mycotoxins have become a global concern. Even though a variety of methods have been developed for mycotoxin detection, most conventional methods suffer from complicated operation procedures, low sensitivity, high cost, and long assay time. Therefore, the development of simple and sensitive methods for mycotoxin assay is highly needed. The introduction of nucleic acid signal amplification technology (NASAT) into aptasensors significantly improves the sensitivity and facilitates the detection of mycotoxins. Herein, we give a comprehensive review of the recent advances in NASAT-based aptasensors for assaying mycotoxins and summarize the principles, features, and applications of NASAT-based aptasensors. Moreover, we highlight the challenges and prospects in the field, including the simultaneous detection of multiple mycotoxins and the development of portable devices for field detection.

Ultrasensitive detection of zearalenone based on electrochemiluminescent immunoassay with Zr-MOF nanoplates and Au@MoS2 nanoflowers

In this work, an effective competitive-type electrochemiluminescence (ECL) immunosensor was constructed for zearalenone determination by using Zr-MOF nanoplates as the ECL luminophore and Au@MoS2 nanoflowers as the substrate material. Zr-MOF have an ultra-thin sheet-like structure that accelerates the transfer of electrons, ions and co-reactant intermediates, which exhibited strong and stable anodic luminescence. The three-dimensional Au@MoS2 nanoflowers would form a thin film modification layer on the glassy carbon electrode (GCE). And its good electrical conductivity and higher specific surface area utilization further improving the sensitivity of the ECL immunosensor. Under the optimized conditions, the proposed immunosensor exhibited satisfactory stability, sensitivity and accuracy, and its ECL signal was proportional to the logarithm of ZEN concentration (0.0001-100 ng/mL) and the limit of detection (LOD) was 0.034 pg/mL. In addition, the results of recovery experiment acquired for wheat flour and pig urine samples further proved the feasibility of the immunosensor for the detection of real samples, indicating its potential for ultrasensitive detection of ZEN.

Programmable DNA tweezers-SDA for ultra-sensitive signal amplification fluorescence sensing strategy

BACKGROUND

DNA tweezers, classified as DNA nanomachines, have gained prominence as multifunctional biosensors due to their advantages, including a straightforward structure, response mechanism, and high programmability. While the DNA tweezers demonstrate simultaneous, rapid, and stable responses to different targets, their detection sensitivity requires enhancement. Some small molecules, such as mycotoxins, often require more sensitive detection due to their extremely high toxicity. Therefore, more effective signal amplification strategies are needed to further enhance the sensitivity of DNA tweezers in biosensing.

RESULTS

We designed programmable DNA tweezers that detect small-molecule mycotoxins and miRNAs through simple sequence substitution. While the DNA tweezers demonstrate simultaneous, rapid, and stable responses to different targets, their detection sensitivity requires enhancement. We introduced the Strand Displacement Amplification (SDA) technique to address this limitation, proposing a strategy of novel programmable DNA tweezers-SDA ultrasensitive signal amplification fluorescence sensing. We specifically investigate the effectiveness of this approach concerning signal amplification for two critical mycotoxins: aflatoxin B1 (AFB1) and zearalenone (ZEN). Results indicate that the detection ranges of AFB1 and ZEN via this strategy were 1-10,000 pg mL -1 and 10-100,000 pg mL -1, respectively, with corresponding detection limits of 0.933 pg mL -1 and 1.07 pg mL -1. Compared with the DNA tweezers direct detection method for mycotoxins, the newly constructed programmable DNA tweezers-SDA fluorescence sensing strategy achieved a remarkable 104-fold increase in the detection sensitivity for AFB1 and ZEN.

SIGNIFICANCE

The constructed programmable DNA tweezers-SDA ultrasensitive signal-amplified fluorescence sensing strategy exhibits excellent detection performance for mycotoxins. The superb versatility of this strategy allows the developed method to be easily used for detecting other analytes by simply replacing the aptamer and cDNA, which has incredible potential in various fields such as food safety screening, clinical diagnostics, and environmental analysis.

A bimetallic organic framework based fluorescent aptamer probe for the detection of zearalenone in cereals

In this work, a bimetallic organic framework (Cu/UiO-66) based "turn on" fluorescent aptamer probe was designed for the high-efficiency detection of zearalenone (ZEN). In the probe, the 6-carboxyfluorescein-labeled aptamer (FAM-Apt) was used as the recognition element, and the electrostatic interaction, coordination effect, and photoinduced electron transfer effect between FAM-Apt and Cu/UiO-66 caused fluorescence quenching. When ZEN existed, FAM-Apt recognized ZEN specifically, causing FAM-Apt to separate from the surface of Cu/UiO-66 and recovery of fluorescence. Under the optimal conditions, the probe had a linear detection range of 0.5 ng/mL-60 ng/mL, and the detection limit was 0.048 ng/mL. The application potential of the probe was verified by real detection of various cereals and their products, with a standard recovery from 83.67 %-106.8 %. The development of this efficient, rapid, and sensitive ZEN detection method provides a new platform for the quality control of cereals and their products.

Cellular temperature probing using optically trapped single upconversion luminescence

BACKGROUND

The thermally coupled energy states that contribute to the upconversion luminescence of rare earth element-doped nanoparticles have been the subject of intense research due to their potential nanoscale temperature probing. However, the inherent low quantum efficiency of these particles often limits their practical applications, and currently, surface passivation and incorporation of plasmonic particles are being explored to improve the inherent quantum efficiency of the particle. However, the role of these surface passivating layers and the attached plasmonic particles in the temperature sensitivity of upconverting nanoparticles while probing the intercellular temperature has not been investigated thus far, particularly at the single nanoparticle level.

RESULTS

The analysis of the study on the thermal sensitivity of oleate-free UCNP, UCNP@SiO₂, and UCNP@SiO₂@Au particles is carried out at a single particle level in a physiologically relevant temperature range (299 K-319 K) by optically trapping the particle. The thermal relative sensitivity of the as-prepared upconversion nanoparticle (UCNP) is found to be greater than that of UCNP@SiO₂ and UCNP@SiO₂@Au particles in an aqueous medium. An optically trapped single luminescence particle inside the cell is used to monitor the temperature inside the cell by measuring the luminescence from the thermally coupled states. The absolute sensitivity of optically trapped particles inside the biological cell increases with temperature, with a greater impact on the bare UCNP, which exhibits higher values for thermal sensitivity than UCNP@SiO₂ and UCNP@SiO₂@Au. The thermal sensitivity of the trapped particle inside the biological cell at 317 K indicates the thermal sensitivity of UCNP > UCNP@SiO₂@Au > UCNP@SiO₂ particles.

SIGNIFICANCE AND NOVELTY

Compared to bulk sample-based temperature probing, the present study demonstrates temperature measurement at the single particle level by optically trapping the particle and further explores the role of the passivating silica shell and the incorporation of plasmonic particles on thermal sensitivity. Furthermore, thermal sensitivity measurements inside a biological cell at the single particle level are investigated and illustrated that thermal sensitivity at a single particle is sensitive to the measuring environment.

3D flower-like ceria silver co-doped zinc oxide catalyst assembled by nanorod for electrochemical sensing of zearalenone in food samples

To ensure food safety and quality, the development of rapid detection of mycotoxins using sensitive and accurate methods is essential. Zearalenone is one of the mycotoxins found in cereals, and its toxicity poses a serious risk to humans. For this concern, a simple ceria silver co doped zinc oxide (Ce-Ag/ZnO) catalyst was prepared by coprecipitation approach. The physical properties of the catalyst were characterized by XRD, FTIR, XPS, FESEM, and TEM. The Ce-Ag/ZnO catalyst was used as an electrode material for the detection of ZEN in food samples due to its synergistic effect and high catalytic activity. The sensor exhibits good catalytic performance with a detection limit of 0.26 µg/mL. Moreover, the efficiency of the prepared sensor was confirmed by selectivity in interference studies and real-time analysis in food samples. Our research is an essential technique for using trimetallic heterostructures to study the construction of sensors.

Novel insights into versatile nanomaterials integrated bioreceptors toward zearalenone ultrasensitive discrimination

Detrimental contamination of zearalenone (ZEN) in crops and foodstuffs has drawn intensive public attention since it poses an ongoing threat to global food security and human health. Highly sensitive and rapid response ZEN trace analysis suitable for complex matrices at different processing stages is an indispensable part of food production. Conventional detection methods for ZEN encounter many deficiencies and demerits such as sophisticated equipment and heavy labor intensity. Alternatively, the nanomaterial-based biosensors featured with high sensitivity, portability, and miniaturization are springing up and emerging as superb substitutes to monitor ZEN in recent years. Herein, we predominantly devoted to overview the progress in the fabrication strategies and applications of various nanomaterial-based biosensors, highlighting rationales on sensing mechanisms, response types, and practical analytical performance. Synchronously, the versatile nanomaterials integrating with diverse recognition elements for augmenting sensing capabilities are emphasized. Finally, critical challenges and perspectives to expedite ZEN detection are outlooked.

MnO2 nanosheets-triggered oxVB1 fluorescence immunoassay for detection zearalenone

In this study, an alkaline phosphatase (ALP)-mediated fluorescence immunoassay for detecting zearalenone (ZEN) was established based on the oxVB₁ fluorescence signal modulated by MnO₂ nanosheets (MnO₂ NS). As the ALP-antibody content increased, more 2-phosphoascorbic acid (AAP) was hydrolyzed to ascorbic acid (AA) which destroyed the MnO₂ NS rapidly. In the lack of MnO₂ NS, VB₁ cannot be oxidized to oxVB₁ for emitting fluorescence. On the contrary, the fluorescence of oxVB₁ recovered slowly with the decrease of the ALP-antibody concentration. In the optimization condition, the detection limit of this method was 15.5 pg mL^-1. Moreover, the recovery of ZEN in real samples ranged from 94.24 % to 108.26 %, which indicated the remarkable accuracy and reliability of this approach. Meanwhile, the proposal of this fluorescence immunoassay provided a new possibility for detecting other targets by replacing antibodies and antigens.

A Novel and Label-Free Chemiluminescence Detection of Zearalenone Based on a Truncated Aptamer Conjugated with a G-Quadruplex DNAzyme

Zearalenone (ZEN), one of the most frequently occurring mycotoxin contaminants in foods and feeds, poses considerable threat to human and animal health, owing to its acute and chronic toxicities. Thus, rapid and accurate detection of ZEN has attracted broad research interest. In this work, a novel and label-free chemiluminescence aptasensor based on a ZEN aptamer and a G-quadruplex DNAzyme was constructed. It was established on a competitive assay between ZEN and an auxiliary DNA for the aptamer, leading to activation of the G-quadruplex/hemin DNAzyme and subsequent signal amplification by chemiluminescence generation after substrate addition. To maximize the detection sensitivity, numerous key parameters including truncated aptamers were optimized with molecular docking analysis. Upon optimization, our aptasensor exhibited a perfect linear relationship (R² = 0.9996) for ZEN detection in a concentration range of 1-100 ng/mL (3.14-314.10 nM) within 40 min, achieving a detection limit of 2.85 ng/mL (8.95 nM), which was a 6.7-fold improvement over that before optimization. Most importantly, the aptasensor obtained a satisfactory recovery rate of 92.84-137.27% and 84.90-124.24% for ZEN-spiked wheat and maize samples, respectively. Overall, our label-free chemiluminescence aptasensor displayed simplicity, sensitivity, specificity and practicality in real samples, indicating high application prospects in the food supply chain for rapid detection of ZEN.

ssDNA-C3N4 conjugates-based nanozyme sensor array for discriminating mycotoxins

A nanozyme sensor array based on the ssDNA-distensible C3N4 nanosheet sensor elements for discriminating multiple mycotoxins commonly existing in contaminated cereals has been explored. The sensor array exploited (a) three DNA nonspecific sequences (A40, T40, C40) absorbed on the C3N4 nanosheets as sensor elements catalyzing the oxidation of TMB; (b) the presence of five mycotoxins affected the catalytic activity of three nanozymes with various degrees. The parameter (A₀-A) was employed as the signal output to obtain the response patterns for different mycotoxins with the same concentration where A₀ and A were the absorption peak values at 650 nm of oxTMB in the absence and presence of target mycotoxins, respectively. After the raw data was subjected to principal component analysis, 3D canonical score plots were obtained. The sensor array was capable of separating five mycotoxins from each other with 100% accuracy even if the concentration of the mycotoxins was as low as 1 nM. Moreover, the array performed well in discriminating the mycotoxin mixtures with different ratios. Importantly, the practicality of this sensor array was demonstrated by discriminating the five mycotoxins spiking in corn-free samples in 3D canonical score plots, validating that the sensor array can act as a flexible detection tool for food safety. A nanozyme sensor array was developed based on the ssDNA-distensible C3N4 NSs sensor elements for discriminating muitiple mycotoxins.

Recent advances in simultaneous detection strategies for multi-mycotoxins in foods

Mycotoxin contamination has become a challenge in the field of food safety testing, given the increasing emphasis on food safety in recent years. Mycotoxins are widely distributed, in heavily polluted areas. Food contamination with these toxins is difficult to prevent and control. Mycotoxins, as are small-molecule toxic metabolites produced by several species belonging to the genera Aspergillus, Fusarium, and Penicillium growing in food. They are considered teratogenic, carcinogenic, and mutagenic to humans and animals. Food systems are often simultaneously contaminated with multiple mycotoxins. Due to the additive or synergistic toxicological effects caused by the co-existence of multiple mycotoxins, their individual detection requires reliable, accurate, and high-throughput techniques. Currently available, methods for the detection of multiple mycotoxins are mainly based on chromatography, spectroscopy (colorimetry, fluorescence, and surface-enhanced Raman scattering), and electrochemistry. This review provides a comprehensive overview of advances in the multiple detection methods of mycotoxins during the recent 5 years. The principles and features of these techniques are described. The practical applications and challenges associated with assays for multiple detection methods of mycotoxins are summarized. The potential for future development and application is discussed in an effort, to provide standards of references for further research.

Electrochemical aptasensing strategy based on a multivariate polymertitanium-metal-organic framework for zearalenone analysis

An electrochemical aptasensing strategy was developed with a novel bioplatform based on a multivariate titanium metal-organic framework, i.e. MTV polyMOF(Ti), to detect zearalenone (ZEN). MTV polyMOF(Ti) was prepared by using mixed linkers of polyether polymer (pbdc-xa or L₈, pbdc = poly(1,4-benzenedicarboxylate) and 1,4-benzenedicarboxylic acid (H₂bdc or L₀) as well as tetrabutyl titanate as nodes (MTV polyMOF(Ti)-L_8,0). Compared with Ti-MOFs synthesized by using the single ligand of L₈ or L₀, MTV polyMOF(Ti)-L_8,0 shows more porous structure assembled with multilayered nanosheets. In light of the improved electrochemical activity and strong bioaffinity to the aptamer, the aptasensor based on MTV polyMOF(Ti)-L_8,0 shows excellent performance for detecting ZEN with the ultralow detection limit at fg mL^-1 level in the linear range of 10 fg mL^-1 to 10 ng mL^-1, along with good selectivity, reproducibility, stability, regenerability, and applicability.

Evanescent Wave Optical-Fiber Aptasensor for Rapid Detection of Zearalenone in Corn with Unprecedented Sensitivity

Zearalenone (ZEN) is a common mycotoxin pollutant found in agricultural products. Aptamers are attractive recognition biomolecules for the development of mycotoxin biosensors. Even though numerous aptasensors have been reported for the detection of ZEN in recent years, many of them suffer from problems including low sensitivity, low specificity, tedious experimental steps, high-cost, and difficulty of automation. We report here the first evanescent wave optical-fiber aptasensor for the detection of ZEN with unprecedented sensitivity, high specificity, low cost, and easy of automation. In our aptasensor, a 40-nt ZEN-specific aptamer (8Z₃₁) is covalently immobilized on the fiber. The 17-nt fluorophore Cy5.5-labeled complementary DNA strand and ZEN competitively bind with the aptamer immobilized on the fiber, enabling the signal-off fluorescent detection of ZEN. The coating of Tween 80 enhanced both the sensitivity and the reproducibility of the aptasensor. The sensor was able to detect ZEN spiked-in the corn flour extract with a semilog linear detection range of 10 pM-10 nM and a limit of detection (LOD, S/N = 3) of 18.4 ± 4.0 pM (equivalent to 29.3 ± 6.4 ng/kg). The LOD is more than 1000-fold lower than the maximum ZEN residue limits set by China (60 μg/kg) and EU (20 μg/kg). The sensor also has extremely high specificity and showed negligible cross-reactivity to other common mycotoxins. In addition, the sensor was able to be regenerated for 28 times, further decreasing its cost. Our sensor holds great potential for practical applications according to its multiple compelling features.

Highly sensitive and convenient aptasensor based on Au NPs@Ce-TpBpy COF for quantitative determination of zearalenone

In this work, an aptasensor based on a portable U-disk electrochemical workstation in combination with a screen-printed electrode (SPE) is demonstrated for the quantitative determination of zearalenone (ZEN). The aptamer is immobilized on Au NPs@Ce-TpBpy COF (Covalent organic frameworks), which is modified on the surface of glassy carbon electrode. ZEN specifically binds to ZEN aptamer, which hinders the electron transfer and decreases the catalytic current of Au NPs@Ce-TpBpy COF for the reduction of hydrogen peroxide, measured by chronoamperometry (i-t). The quantitative detection of ZEN toxin is realized by a decrease of the catalytic current (ΔI). Under the optimal experimental conditions, the aptamer sensor exhibited excellent sensitivity, selectivity, reproducibility. A wide linear range of 1 pg mL-1-10.0 ng mL-1 with a detection limit of 0.389 pg mL-1 (at 3σ) was obtained. The linear equation is ΔI = 0.401 lg c + 1.948 with a correlation coefficient of 0.9906. The recovery is in the range of 93.0-104.7% for the cornflour samples. The proposed method offers a new strategy for the rapid, inexpensive, and real-time detection of ZEN.

Stability of a calibrant as certified reference material for determination of trans-zearalenone by high performance liquid chromatography-diode array detection-triple quadrupole tandem mass spectrometry

In this study, a trans-zearalenone (trans-ZEN) calibrant in acetonitrile as certified reference material (CRM) was prepared and intensively investigated the stability by high performance liquid chromatography coupled diode array detection and triple quadrupole tandem mass spectrometry (HPLC-DAD-MS/MS). The photoisomerization and degradation of main component and related impurities in trans-ZEN calibrant CRM was studied in detail under different light conditions such as UV light (254 nm), sunlight, and visible light. Trans-ZEN in acetonitrile was confirmed a significant shift toward cis-ZEN up to a 52% cis-isomerization rate after exposing to UV light (254 nm) in transparent ampule for 1 day. The unsaturated double bond photosensitive groups of trans-ZEN and cis-ZEN will further undergo photoreaction to generate more isomers and related products with the increase of UV irradiation time. The calibrant in amber ampules was relatively stable after exposing to sunlight for 28 days, with only 0.35% cis-isomer observed. The results indicated that trans-ZEN solution calibrant should be packed in amber ampules to avoid UV rays. Thermal stability test exhibited this calibrant was stable over 6 weeks even at 60 °C. Trans-ZEN was found to be more stable in acetonitrile than in methanol since an unknown impurity was observed in methanol after 6 weeks placed at 25 °C. The stability study of trans-ZEN calibrant provided a basis for the usage, storage, and transportation of the CRM. A concentration and expanded uncertainty of the trans-ZEN calibrant CRM of 11.01 ± 0.18 µg/mL was developed.

Development of isotope dilution-liquid chromatography/tandem mass spectrometry for the accurate determination of zearalenone and its metabolites in corn

A method using isotope dilution-liquid chromatography-tandem mass spectrometry (ID-LC/MS/MS) was developed for the accurate determination of zearalenone (ZEN) and its five major metabolites in corn. ¹³C- or ²H-labeled analogues of the target mycotoxins were used as internal standards. As the immunoaffinity columns used demonstrated selectivity to a specific chiral isomer of a racemic mixture of zearalanone-d₆, a clean-up cartridge without stereoselectivity (Mycosep 226 column) was selected for the same recovery of the analyte and its internal standard with adequate elimination of matrix interferences. The method demonstrated sufficient selectivity, sensitivity, accuracy and precision over a concentration range of 20-400 µg/kg. The limit of detections and limit of quantifications were 0.14-0.33 µg/kg and 0.45-1.11 µg/kg, respectively. The accuracy values were 96.7%-103.6%, with intra and inter-day precisions of less than 3% and 4%, respectively. The expanded measurement uncertainty was less than 7% (with a 95% confidence level).

A label-free electrochemical immunosensing platform based on PEI-rGO/Pt@Au NRs for rapid and sensitive detection of zearalenone

In this work, we design an immunosensor for zearalenone (ZEN) detection with PEI-rGO/Pt@Au NRs nanocomposite as the modification material. PEI-rGO/Pt@Au NRs nanocomposite have good stability, conductivity and a large specific surface area, so they are chosen as the substrate material for the modified electrode, which is beneficial in improving the detection performance of the sensor. When antibody binds to ZEN, the current signal decreases, and the response signal changes after ZEN incubation, recorded by differential pulse voltammetry (DPV) methods. Under the optimised conditions, the electrochemical response of the constructed immunosensor shows a linear relation to a wide concentration range from 1 pg/mL to 1 × 106 pg/mL with a detection limit of 0.02 pg/mL. Additionally, the proposed electrochemical immunosensor has high selectivity, good stability and great potential for the trace detection of ZEN in real samples.

Quantum dot microsphere-based immunochromatography test strip enabled sensitive and quantitative on-site detections for multiple mycotoxins in grains

In this work, we design a sensitive and quantitative on-site detecting solution for Aflatoxin B1 (AFB1), Ochratoxin A (OTA) and Zearalenone (ZEN) as often found in moldy grains and harmful to human health. Using quantum dot microsphere-based immunochromatography test strip, the proposed method can sensitively detect AFB1, OTA and ZEN in low detection limits of 0.01 ng/mL, 0.2 ng/mL and 0.032 ng/mL, and quantitatively measure their concentrations from 0.01 ng/mL to 1 ng/mL, from 0.2 ng/mL to 200 ng/mL and from 0.032 ng/mL to 32 ng/mL in high accuracy and good selectivity. More importantly, these multiple mycotoxin detections only relying on simple manual operations and portable handheld test strip reader can be finished on site within 45 min. Therefore, the proposed method is a promising solution supporting sensitive and quantitative on-site detections for multiple mycotoxins.

A novel approach to design electrochemical aptamer-based biosensor for ultrasensitive detecting of zearalenone as a prevalent estrogenic mycotoxin

BACKGROUND

Zearalenone is a well-known estrogenic mycotoxin produced by Fusarium species, a serious threat to the agricultural and food industries worldwide. Zearalenone, with its known metabolites, are biomarkers of exposure to certain fungi, primarily through food. It has considerable toxic effects on biological systems due to its carcinogenicity, mutagenicity, renal toxicity, teratogenicity, and immunotoxicity.

INTRODUCTION

This study aims to design a simple, quick, precise, and cost-effective method on a biosensor platform to evaluate the low levels of this toxin in foodstuffs and agricultural products.

METHODS

An aptamer-based electrochemical biosensor was introduced that utilizes screen-printed gold electrodes instead of conventional electrodes. The electrode position process was employed to develop a gold nanoparticle-modified surface to enhance the electroactive surface area. Thiolated aptamers were immobilized on the surface of gold nanoparticles, and subsequently, the blocker and analyte were added to the modified surface. In the presence of a redox probe, electrochemical characterization of differential pulse voltammetry, cyclic voltammetry, and electrochemical impedance spectroscopy were used to investigate the various stages of aptasensor fabrication.

RESULTS

The proposed aptasensor for zearalenone concentration had a wide linear dynamic range covering the 0.5 pg/mL to 100 ng/mL with a 0.14 pg/mL detection limit. Moreover, this aptasensor had high specificity so that a non-specific analyte cannot negatively affect the selectivity of the aptasensor.

CONCLUSION

Overall, due to its simple design, high sensitivity, and fast performance, this aptasensor showed a high potential for assessing zearalenone in real samples, providing a clear perspective for designing a portable and cost-effective device.

Aptasensors for mycotoxins in foods: Recent advances and future trends

Mycotoxin contamination in foods has posed serious threat to public health and raised worldwide concern. The development of simple, rapid, facile, and cost-effective methods for mycotoxin detection is of urgent need. Aptamer-based sensors, abbreviated as aptasensors, with excellent recognition capacity to a wide variety of mycotoxins have attracted ever-increasing interest of researchers because of their simple fabrication, rapid response, high sensitivity, low cost, and easy adaptability for in situ measurement. The past few decades have witnessed the rapid advances of aptasensors for mycotoxin detection in foods. Therefore, this review first summarizes the reported aptamer sequences specific for mycotoxins. Then, the recent 5-year advancements in various newly developed aptasensors, which, according to the signal output mode, are divided into electrochemical, optical and photoelectrochemical categories, for mycotoxin detection are comprehensively discussed. A special attention is taken on their strengths and limitations in real-world application. Finally, the current challenges and future perspectives for developing novel highly reliable aptasensors for mycotoxin detection are highlighted, which is expected to provide powerful references for their thorough research and extended applications. Owing to their unique advantages, aptasensors display a fascinating prospect in food field for safety inspection and risk assessment.

Exploring the use of upconversion nanoparticles in chemical and biological sensors: from surface modifications to point-of-care devices

Upconversion nanoparticles (UCNPs) have emerged as promising luminescent nanomaterials due to their unique features that allow the overcoming of several problems associated with conventional fluorescent probes. Although UCNPs have been used in a broad range of applications, it is probably in the field of sensing where they best evidence their potential. UCNP-based sensors have been designed with high sensitivity and selectivity, for detection and quantification of multiple analytes ranging from metal ions to biomolecules. In this review, we deeply explore the use of UCNPs in sensing systems emphasizing the most relevant and recent studies on the topic and explaining how these platforms are constructed. Before diving into UCNP-based sensing platforms it is important to understand the unique characteristics of these nanoparticles, why they are attracting so much attention, and the most significant interactions occurring between UCNPs and additional probes. These points are covered over the first two sections of the article and then we explore the types of fluorescent responses, the possible analytes, and the UCNPs' integration with various material types such as gold nanostructures, quantum dots and dyes. All the topics are supported by analysis of recently reported sensors, focusing on how they are built, the materials' interactions, the involved synthesis and functionalization mechanisms, and the conjugation strategies. Finally, we explore the use of UCNPs in paper-based sensors and how these platforms are paving the way for the development of new point-of-care devices.

Biosensors for Deoxynivalenol and Zearalenone Determination in Feed Quality Control

Mycotoxin contamination of cereals used for feed can cause intoxication, especially in farm animals; therefore, efficient analytical tools for the qualitative and quantitative analysis of toxic fungal metabolites in feed are required. Current trends in food/feed analysis are focusing on the application of biosensor technologies that offer fast and highly selective and sensitive detection with minimal sample treatment and reagents required. The article presents an overview of the recent progress of the development of biosensors for deoxynivalenol and zearalenone determination in cereals and feed. Novel biosensitive materials and highly sensitive detection methods applied for the sensors and the application of these sensors to food/feed products, the limit, and the time of detection are discussed.

Multiple fluorescence immunoassay for the simultaneous detection of Zearalenone and Ochratoxin A

A sensitive and accurate multiple fluorescence immunoassay for the simultaneous quantitative detection of Zearalenone (ZEN) and Ochratoxin A (OTA) in single spot based on multicolor quantum dots (QDs) labeling was developed for the first time. Two kinds of ZnCdSe/ZnS (core/shell) QDs with maximum emission wavelengths at 520 nm (green) and 610 nm (orange-red) were selected as marking materials, respectively. The anti-ZEN-mAb-QDs and anti-OTA-mAb-QDs were designed as the immune fluorescent probes. Fluorescence was measured at the same excitation wavelength and two different emission wavelengths to determine each target. The procedure for QDs-based multiple fluorescence labeled immunosorbent assay (M-FLISA) was developed. The 50% inhibition concentrations (IC₅₀) of ZEN and OTA were 0.034 and 1.175 ng/mL. Moreover, the limits of detection (LOD) for the simultaneous determination were 0.0239 and 2.339 ng/g for ZEN and OTA in maize, respectively. In addition, the recoveries ranged from 93.15 to 101.90% for ZEN and from 95.29 to 102.43% for OTA, with the coefficient variation (CV) of 2.70-8.86% and 3.51-6.22% respectively. There was good consistency between the M-FLISA and high performance liquid chromatography (HPLC) results, which confirmed that the M-FLISA was suitable for the simultaneous quantitative detection of various mycotoxins.

Lanthanide ion (Ln3+ )-based upconversion sensor for quantification of food contaminants: A review

The food safety issue has gradually become the focus of attention in modern society. The presence of food contaminants poses a threat to human health and there are a number of interesting researches on the detection of food contaminants. Upconversion nanoparticles (UCNPs) are superior to other fluorescence materials, considering the benefits of large anti-Stokes shifts, high chemical stability, non-autofluorescence, good light penetration ability, and low toxicity. These properties render UCNPs promising candidates as luminescent labels in biodetection, which provides opportunities as a sensitive, accurate, and rapid detection method. This paper intended to review the research progress of food contaminants detection by UCNPs-based sensors. We have proposed the key criteria for UCNPs in the detection of food contaminants. Additionally, it highlighted the construction process of the UCNPs-based sensors, which includes the synthesis and modification of UCNPs, selection of the recognition elements, and consideration of the detection principle. Moreover, six kinds of food contaminants detected by UCNPs technology in the past 5 years have been summarized and discussed fairly. Last but not least, it is outlined that UCNPs have great potential to be applied in food safety detection and threw new insight into the challenges ahead.

Biosensing based on upconversion nanoparticles for food quality and safety applications

Food safety and quality regulations inevitably call for sensitive and accurate analytical methods to detect harmful contaminants in food and to ensure safe food for the consumer. Both novel and well-established biorecognition elements, together with different transduction schemes, enable the simple and rapid analysis of various food contaminants. Upconversion nanoparticles (UCNPs) are inorganic nanocrystals that convert near-infrared light into shorter wavelength emission. This unique photophysical feature, along with narrow emission bandwidths and large anti-Stokes shift, render UCNPs excellent optical labels for biosensing because they can be detected without optical background interferences from the sample matrix. In this review, we show how this exciting technique has evolved into biosensing platforms for food quality and safety monitoring and highlight recent applications in the field.

A highly sensitive immunofluorescence sensor based on bicolor upconversion and magnetic separation for simultaneous detection of fumonisin B1 and zearalenone

Mycotoxins cause significant harm to human health, so it is imperative to develop a highly sensitive and easy-to-operate method for the detection of mycotoxins. Herein, a fluorescence-based magnetic separation immunoassay for simultaneous detection of mycotoxins fumonisin B1 and zearalenone is established. The method employed high fluorescent upconversion-nanoparticles(UCNPs) conjugated with biotinylated antigens as upconversion fluoroscent probes. Magnetic nanoparticles(MNPs) immobilized with monoclonal antibodies are used as immune-capture probes. Highly sensitive detection of FB1 and ZEN was achieved based on the luminescence properties of UCNPs and the separation effects of MNPs. The results showed a robust linear correlation between the enhanced fluorescence emission intensity and the logarithmic concentrations of FB1 and ZEN under the optimal conditions (R²(FB1) = 0.9965, R²(ZEN) = 0.9976), and the linear ranges were 0.05-5 ng mL^-1. Furthermore, the limits of detection (LOD) were 0.016 ng mL^-1 for FB1 and 0.012 ng mL^-1 for ZEN. The standard addition method was used to determine the content of FB1 and ZEN in the samples to evaluate the accuracy of the process. The average recoveries were 89.48% to 113.69% and 85.97% to 113.82%, respectively. Compared with the other five mycotoxins, this method had high selectivity. It is expected that the multi-component simultaneous detection can be further realized by using the multicolor labeling characteristics of UCNPs.

Novel Nondestructive Biosensors for the Food Industry

An increasing number of foodborne outbreaks, growing consumer desire for healthier products, and surging numbers of food allergy cases necessitate strict handling and screening of foods at every step of the food supply chain. Current standard procedures for detecting food toxins, contaminants, allergens, and pathogens require costly analytical devices, skilled technicians, and long sample preparation times. These challenges can be overcome with the use of biosensors because they provide accurate, rapid, selective, qualitative, and quantitative detection of analytes. Their ease of use, low-cost production, portability, and nondestructive measurement techniques also enable on-site detection of analytes. For this reason, biosensors find many applications in food safety and quality assessments. The detection mechanisms of biosensors can be varied with the use of different transducers, such as optical, electrochemical, or mechanical. These options provide a more appropriate selection of the biosensors for the intended use. In this review, recent studies focusing on the fabrication of biosensors for food safety or food quality purposes are summarized. To differentiate the detection mechanisms, the review is divided into sections based on the transducer type used.

Advances in gold nanoparticles for mycotoxin analysis

Mycotoxins are toxic secondary metabolites naturally produced by fungi. They can cause various kinds of acute and chronic diseases in both humans and animals since food usually contains trace amounts of mycotoxins. Thus, it is important to develop a rapid and sensitive technique for mycotoxin detection. Except for the original and classical enzyme-linked immunosorbent assays (ELISA), a series of biosensors has been developed to analyze mycotoxins in food in the last decade with the advantages of rapid analysis, simplicity, portability, reproducibility, stability, accuracy, and low cost. Nanomaterials have been incorporated into biosensors for the purpose of achieving better analytical performance in terms of limit of detection, linear range, analytical stability, low production cost, etc. Gold nanoparticles (AuNPs) are one of the most extensively studied and commonly used nanomaterials, which can be employed as an immobilization carrier, signal amplifier, mediator and mimic enzyme label. This paper aims to present an extensive overview of the recent progress in AuNPs in mycotoxin detection through ELISA and biosensors. The details of the detection methods and their application principles are described, and current challenges and future prospects are discussed as well.

Inner filter effect-modulated ratiometric fluorescence aptasensor based on competition strategy for zearalenone detection in cereal crops: Using mitoxantrone as quencher of CdTe QDs@SiO2

Herein, an innovative ratiometric fluorescence (FL) aptasensor was successfully fabricated for the accurate analysis of zearalenone (ZEN) in corn and barley flour. The ZEN aptamer-modified nitrogen doped graphene quantum dots (NGQDs-apt) and silica sphere-encapsulated cadmium telluride quantum dots (CdTe QDs@SiO₂) were directly mixed and applied as ratiometric probes. In the absence of ZEN, mitoxantrone (MTX), which was innovatively introduced as quencher, was captured by NGQDs-apt and its inner filter effect (IFE) on CdTe QDs@SiO₂ was inhibited. When ZEN existed, MTX separated from NGQDs-apt and re-dispersed around CdTe QDs@SiO₂ owing to the competitive binding of ZEN with its aptamer. As the IFE of free MTX on CdTe QDs@SiO₂ recovering, the FL intensity of CdTe QDs@SiO₂ was quenched, while the FL intensity of NGQDs-apt was nearly invariant. On this basis, a ratiometric FL aptasensor for ZEN was fabricated, which exhibited outstanding detection performances with a desirable detection limit of 0.32 pg mL^-1.

FEAST of biosensors: Food, environmental and agricultural sensing technologies (FEAST) in North America

We review the challenges and opportunities for biosensor research in North America aimed to accelerate translational research. We call for platform approaches based on: i) tools that can support interoperability between food, environment and agriculture, ii) open-source tools for analytics, iii) algorithms used for data and information arbitrage, and iv) use-inspired sensor design. We summarize select mobile devices and phone-based biosensors that couple analytical systems with biosensors for improving decision support. Over 100 biosensors developed by labs in North America were analyzed, including lab-based and portable devices. The results of this literature review show that nearly one quarter of the manuscripts focused on fundamental platform development or material characterization. Among the biosensors analyzed for food (post-harvest) or environmental applications, most devices were based on optical transduction (whether a lab assay or portable device). Most biosensors for agricultural applications were based on electrochemical transduction and few utilized a mobile platform. Presently, the FEAST of biosensors has produced a wealth of opportunity but faces a famine of actionable information without a platform for analytics.

Ultra-sensitive detection of malathion residues using FRET-based upconversion fluorescence sensor in food

Malathion is an organophosphorus pesticide which could remain in agricultural products and exert irreversible harmful effects on human health. Hence, strict monitoring of malathion contents is very significant. Here, a highly sensitive fluorescent aptasensor was developed for the determination of malathion, the system was based on a cationic polymer-mediated fluorescence 'turn-off'. In this system, malathion-specific aptamers were bound to cationic polymer through electrostatic interactions. To produce fluorescence resonance energy transfer (FRET), negatively charged upconversion fluorescent nanoparticles (UCNPs) and cationic-polymer encapsulated gold nanoparticles (GNPs) were combined. This combination resulted in fluorescence quenching, and the degree of quenching was correlated with the concentration of malathion. Under optimum conditions, the fluorescence intensities were observed to decrease linearly with the rising concentration of the malathion from 0.01 to 1 μM with a detection limit of 1.42 nM. Furthermore, the developed sensor possessed good selective recognition ability for malathion and was successfully used to detect malathion in adulterated tap water and matcha samples with high accuracy.

Detection Strategies of Zearalenone for Food Safety: A Review

Zearalenone (ZEN) is a toxic compound produced by the metabolism of fungi (genus Fusarium) that threaten the food and agricultural industry belonging to the in foods and feeds. ZEN has toxic effects on human and animal health due to its mutagenicity, teratogenicity, carcinogenicity, nephrotoxicity, immunotoxicity, and genotoxicity. To ensure food safety, rapid, precise, and reliable analytical methods can be developed for the detection of toxins such as ZEN. Different selective molecular diagnostic elements are used in conjunction with different detection strategies to achieve this goal. In this review, the use of electrochemical, colorimetric, fluorometric, refractometric as well as other strategies were discussed for ZEN detection. The success of the sensors in analytical performance depends on the development of receptors with increased affinity to the target. This requirement has been met with different immunoassays, aptamer-assays, and molecular imprinting techniques. The immobilization techniques and analysis strategies developed with the combination of nanomaterials provided high precision, reliability, and convenience in ZEN detection, in which electrochemical strategies perform the best.

Simultaneous Detection of Multiple β-Adrenergic Agonists with 2-Directional Lateral Flow Strip Platform

Clenbuterol (CL), salbutamol (SAL) and ractopamine (RAC) are the three common β-adrenergic agonists, which are the main hazards in food safety and affect human health through the food chain. A convenient and efficient method is urgently required to perform on-site detection of multiple β-adrenergic agonists to avoid frequent poisoning incidents. In this paper, a 2-directional lateral flow strip technique (2-directional LFS) is developed for rapid and simultaneous detection of CL, SAL and RAC with single sampling. Compared to the conventional lateral flow strip, this 2-directional LFS technique can realize simultaneous detection of three or more target analytes without any change of intrinsic simplicity of LFS. Furthermore, this 2-directional LFS can effectively avoid the potential intrinsic cross-reactivity among the reagents to analogues. Under the optimized conditions, CL, SAL and RAC were all successfully determined with satisfactory results in both buffer and urine samples with the detection limit as low as 0.5 ng/mL. This 2-directional LFS technique can revolutionize the commercial single-analyte LFS products and can effectively widen the applications of the classic LFS in various fields.

Aptamer-Based Biosensor for Detection of Mycotoxins

Mycotoxins are a large type of secondary metabolites produced by fungi that pose a great hazard to and cause toxic reactions in humans and animals. A majority of countries and regulators, such as the European Union, have established a series of requirements for their use, and they have also set maximum tolerance levels. The development of high sensitivity and a specific analytical platform for mycotoxins is much in demand to address new challenges for food safety worldwide. Due to the superiority of simple, rapid, and low-cost characteristics, aptamer-based biosensors have successfully been developed for the detection of various mycotoxins with high sensitivity and selectivity compared with traditional instrumental methods and immunological approaches. In this article, we discuss and analyze the development of aptasensors for mycotoxins determination in food and agricultural products over the last 11 years and cover the literatures from the first report in 2008 until the present time. In addition, challenges and future trends for the selection of aptamers toward various mycotoxins and aptasensors for multi-mycotoxins analyses are summarized. Given the promising development and potential application of aptasensors, future research studies made will witness the great practicality of using aptamer-based biosensors within the field of food safety.

Ionic liquid assisted molecular self-assemble and molecular imprinting on gold nanoparticles decorated boron-doped ordered mesoporous carbon for the detection of zearalenone

Accurate and early diagnosis of zearalenone (ZEN) is particularly significant to the food safety. Herein, we propose an ionic liquid assisted self-assembly molecular imprinting strategy for ZEN based on ionic liquid functionalized boron-doped ordered mesoporous carbon -gold nanoparticles composite (BOMC-IL-Au NPs). During the composite synthesis, increased well-dispersed and uniform Au NPs are deposited on the surface of IL modified BOMC, due to the strong electrostatic interaction between AuCl₄^- and positively charged IL. For molecular imprinting, the BOMC-IL-Au NPs/GCE is immersed into p-aminothiophenol (p-ATP) solution and template solution in turn. Thus, the mercapto group contained p-ATP self-assembles on the Au NPs. Subsequently, the template molecules self-assemble onto the composite to form dense template layer, because of the hydrophobic interaction, π-π and hydrogen bond between template and IL/or p-ATP. After electropolymerization, the template layer is embedded into the p-ATP polymer membrane and produces lots of imprinting sites. Hence, the obtained sensor exhibits high sensitivity and selectivity. Under the optimal conditions, zearalenone can be quantified from 5 × 10^-4 to 1 ng mL^-1 with the low detection limit of 1 × 10^-4 ng mL^-1, by using [Fe(CN)₆]^3-/4- probe and square wave voltammetry. This strategy can also be employed to construct sensors for the detection of other substances.