Quantification of zearalenone in mildewing cereal crops using an innovative photoelectrochemical aptamer sensing strategy based on ZnO-NGQDs composites

Amplified electrochemiluminescence of Ru(dcbpy)32+ via coreactant active sites on nitrogen-doped graphene quantum dots

Searching for new alternative to tripropylamine (TPrA) with low toxicity and high chemical stability for the tris(4,4'-dicarboxylic acid-2,2'-bipyridyl)ruthenium (II) (Ru(dcbpy)32+) based coreactant electrochemiluminescence (ECL) system is essential for widespread analytical applications. Here, nitrogen-doped graphene quantum dots (NGQDs) have been discovered to significantly amplify the ECL emission and increase the ECL efficiency of Ru(dcbpy)32+ for the first time. However, the mechanism by which NGQDs act as coreactants is not well comprehended. Therefore, various optical and electrochemical technologies were employed to investigate the ECL mechanism. It is proposed that the amino and carboxyl groups on the surface of NGQDs play crucial roles as the coreactant active sites, catalyzing the oxidation of Ru(dcbpy)32+. Based on this foundation, an "on-off-on" ECL aptasensor for the quantification of acetamiprid was developed, exhibiting a broad linear range and a detection limit of 0.056 pM. Satisfactory recoveries, ranging from 98.0 % to 101.6 %, were achieved in pakchoi samples. Consequently, NGQDs could serve as coreactants for Ru(dcbpy)32+, offering new opportunities for constructing a variety of sensors with extensive analytical applications in the ECL field.

Sensing technology empowering food safety: research progress of SERS-assisted multimodal biosensing toward food hazard factors

Food is the main source of human energy and nutrition, but once it is contaminated with hazardous factors, such as biotoxins, pesticide residues, etc., it will seriously damage health. This paper reviews the research progress of biosensors based on surface-enhanced Raman scattering (SERS) in the detection of food hazard factors. First, the basic principle, substrate and assay mode of SERS technology, as well as related design and sensing strategy mechanisms, are introduced. Then, the design idea of multimodal biosensors combining SERS with microfluidic, fluorescence, colorimetric, electrochemical (EC), molecular imprinting and other technologies is expounded to improve the analysis accuracy and specificity. Then the application results of multimodal biosensors based on SERS sensing toward food hazard factors are discussed, and the necessity of its development is illustrated. Finally, the future development direction of this field is prospected, which provides a reference for promoting the research and application of multimodal biosensors based on SERS.

Research Progress on the Application of Metal Porphyrin Electrochemical Sensors in the Detection of Phenolic Antioxidants in Food

This paper reviews the application of metal porphyrin electrochemical sensors in the detection of phenolic antioxidants in food, focusing on the latest progress and innovative applications in this field. Phenolic antioxidants are widely used in food and can effectively prolong the shelf life of food, but their excessive use may cause potential harm to human health, so the detection of their content is very important. In recent years, electrochemical analysis technology has gradually become an emerging method for quantitative detection of phenolic antioxidants due to its advantages of sensitivity, simplicity and high selectivity. As a new type of sensor, metal porphyrin electrochemical sensors have been widely used in the detection of phenolic antioxidants in food due to their excellent electrochemical performance and high selectivity. By modifying metal nanomaterials, the detection performance of these sensors has been significantly improved. This paper first introduces the basic concepts and physicochemical properties of phenolic antioxidants, analyzes their potential hazards and discusses relevant regulations and limit requirements. Then, the existing analysis methods of phenolic antioxidants are compared, and the development trend of traditional detection methods and new detection technologies is reviewed. Subsequently, the application progress of electrochemical sensors in the detection of phenolic antioxidants is discussed in depth, its working principle is expounded and the research results are summarized. Finally, the innovative applications of metalloporphyrins and their nanocomposites in electrochemical sensors are introduced in detail. The unique advantages of metalloporphyrins in the detection of phenolic antioxidants in food are highlighted, and the future development direction is laid out.

Generalized Synthetic Strategies toward Oxygen Vacancy-Enriched ZnO-ZnS Hollow Porous Spheres with Enhanced Photocatalytic Hydrogen Evolution

Constructing a hollow porous ZnO-ZnS sphere is still a big challenge due to the difficulty in controlling the morphology and distribution of ZnO shell originating from the fact that ZnO prefers to grow along particular crystal planes. Here, we demonstrate a novel synthetic strategy for the preparation of oxygen-vacancy-enriched ZnO-ZnS hollow porous (Ov-ZOS (HP)) spheres by combining the concepts of adopting a template-directed method, selecting the sulfidation precursor, and tuning the calcination process of the template. Structural characterization and density functional theory (DFT) calculations reveal that hollow porous nanostructures and oxygen vacancies in the ZnO-ZnS heterojunction are beneficial in promoting efficient charge transfer and separation. The optimized Ov-ZOS (HP) exhibits enhanced rates of hydrogen evolution reaction (71.86 mmol h-1 g-1), which is 1.48, 2.08, and 3.0 times higher than those of ZnO-ZnS hollow porous spheres, oxygen vacancy-enriched ZnO-ZnS nanosheets, ZnO-ZnS nanosheets, respectively. Moreover, the Ov-ZOS (HP) presents excellent cyclability for photocatalytic hydrogen evolution. Therefore, this study provides physical insights into controlling the hollow porous nanostructures of various semiconductor heterojunctions that are hard to form through other existing strategies for solar energy utilization.

Self-designed portable dual-mode fluorescence device with custom python-based analysis software for rapid detection via dual-color FRET aptasensor with IoT capabilities

An innovative aptasensor incorporating MoS2-modified bicolor quantum dots and a portable spectrometer, designed for the simultaneous detection of ochratoxin A (OTA) and aflatoxin B1 (AFB1) in corn was developed. Carbon dots and CdZnTe quantum dots were as nano-donors to label OTA and AFB1 aptamers, respectively. These labeled aptamers were subsequently attached to MoS2 receptors, enabling fluorescence resonance energy transfer (FRET). With targets, the labeled aptamers detached from the nano-donors, thereby disrupting the FRET process and resulting in fluorescence recovery. Furthermore, a portable dual-mode fluorescence detection system, complemented with customized python-based analysis software, was developed to facilitate rapid and convenient detection using this dual-color FRET aptasensor. The developed host program is connected to the spectrometer and transmits data to the cloud, enabling the device to have Internet of Things (IoT) characteristics. Connected to the cloud, this IoT-enabled device offers convenient and reliable fungal toxin detection for food safety.

Ultrasensitive monitoring of PCB77 in environmental samples using a visible-driven photoelectrochemical sensing platform coupling with exonuclease I assisted in target recycling

Due to the urgent need for detecting trace amounts of 3,3',4,4'-tetrachlorobiphenyl (PCB77) in the environment, we have developed an efficient and visible-driven photoelectrochemical (PEC) sensing platform based on carbon quantum dots (CQDs) modified titanium dioxide nanorods (TiO2 NRs), coupling with exonuclease I (Exo I) assisted in target recycling for significant signal amplification. CQDs/TiO2 NRs with high visible-light absorption ability and electron-hole separation efficiency is used as photoactive substrate for anchoring anti-PCB77 aptamer and its complementary DNA (cDNA). With the addition of PCB77, the specific interaction between PCB77 and its aptamer forces aptamer to separate from the electrode surface, resulting in an increase in photocurrent density. Adding Exo I in the test system, a self-catalytic target cycle was motivated, which significantly increased the PEC signal by more than twice, achieving signal amplification. The relationship between the photocurrent density changes and the concentrations of PCB77 are utilized to achieve quantitative detection of PCB77. The designed PEC sensing platform has good analytical performance with a detection limit as low as 0.33 pg L-1, high selectivity and stability. Moreover, the PEC sensor is successfully used to evaluate the content of PBC77 in the environment samples. The established sensing platform provides a simple and efficient method for detecting trace amounts of PCB77 in the environment.

A potential-controlled electrochromic visual biosensor based on distance readout for zearalenone detection

In this work, a potential-controlled electrochromic visual biosensor was developed for detecting zearalenone (ZEN) using a distance readout strategy. The sensor chip includes a square detection area and a folded signal output area created with laser etching technology. The detection area is modified with graphene oxide and ZEN aptamer, while Prussian blue (PB) is electrodeposited onto the signal output channel. When an appropriate voltage is applied, PB in the signal output area is reduced to colorless Prussian white (PW). The target ZEN molecules have the capability to release aptamers from graphene oxide (GO) surface in the detection area, resulting in a subsequent change in the potential of the visual signal output channel. This change determines the length of the channel that changes from blue to colorless, with the color change distance being proportional to the ZEN concentration. Using this distance readout strategy, ZEN detection within the range of 1 ng/mL to 300 ng/mL was achieved, with a detection limit of 0.29 ng/mL.

Integrating CdIn2S4 semiconductors with S-vacancy MoS2 nanosheets to fabricate a multi-channel aptasensing chip for photoelectrochemical detection of multiple mycotoxins

BACKGROUND

The importance of multi-target simultaneous detection lies in its ability to significantly boost detection efficiency, making it invaluable for rapid and cost-effective testing. Photoelectrochemical (PEC) sensors have emerged as promising candidates for detecting harmful substances and biomarkers, attributable to their unparalleled sensitivity, minimal background signal, cost-effectiveness, equipment simplicity, and outstanding repeatability. However, designing an effective multi-target detection strategy remains a challenging task in the PEC sensing field. Consequently, there is a pressing need to address the development of PEC sensors capable of simultaneously detecting multiple targets.

RESULTS

CdIn2S4/V-MoS2 heterojunctions were successfully prepared via a hydrothermal method. These heterojunctions exhibited a high photocurrent intensity, representing a 1.53-fold enhancement compared to CdIn2S4 alone. Next, we designed a multi-channel aptasensing chip using ITO as the substrate. Three working electrodes were created via laser etching and subsequently modified with CdIn2S4/V-MoS2 heterojunctions. Thiolated aptamers were then self-assembled onto the CdIn2S4/V-MoS2 heterojunctions via covalent bonds, serving as recognition tool. By empolying the CdIn2S4/V-MoS2 heterojunctions as the sensing platform and aptamers as recognition tool, we successfully developed a disposable aptasensing chip for the simultaneous PEC detection of three typical mycotoxins (aflatoxin B1 (AFB1), ochratoxin A (OTA), and zearalenone (ZEN)). This aptasensing chip exhibited wide detection range for AFB1 (0.05-50 ng/mL), OTA (0.05-500 ng/mL), and ZEN (0.1-250 ng/mL). Furthermore, it demonstrated ultra-low detection limits of 0.017 ng/mL for AFB1, 0.016 ng/mL for OTA, and 0.033 ng/mL for ZEN.

SIGNIFICANCE AND NOVELTY

The aptasensing chip stands out for its cost-effectiveness, simplicity of fabrication, and multi-channel capabilities. The versatility and practicality enable it to serve as a powerful platform for designing multi-channel PEC aptasensors. With its ability to detect multiple targets with high sensitivity and specificity, the aptasensing chip holds immense potential for applications across diverse fields, such as environmental monitoring, clinical diagnostics, and food safety monitoring, where multi-target detection is crucial.

Carbon-based photoelectrochemical sensors: recent developments and future prospects

Owing to the considerable potential of photoelectrochemical (PEC) sensors, they have gained significant attention in the analysis of biological, environmental, and food markers. However, the limited charge mass transfer efficiency and rapid recombination of electron hole pairs have become obstacles in the development of PEC sensors. In this case, considering the unique advantages of carbon-based materials, they can be used as photosensitizers, supporting materials and conductive substrates and coupled with semiconductors to prepare composite materials, solving the above problems. In addition, there are many types of carbon materials, which can have semiconductor properties and form heterojunctions after coupling with semiconductors, effectively promoting the separation of electron hole pairs. Herein, we aimed to provide a comprehensive analysis of reports on carbon-based PEC sensors by introducing their research and application status and discussing future development trends in this field. In particular, the types and performance improvement strategies of carbon-based electrodes and the working principles of carbon-based PEC sensors are explained. Furthermore, the applications of carbon-based photoelectric sensors in environmental monitoring, biomedicine, and food detection are highlighted. Finally, the current limitations in the research on carbon-based PEC sensors are emphasized and the need to enhance the sensitivity and selectivity through material modification, structural design, improved device performance, and other strategies are emphasized.

Polycarboxyl ionic liquid functionalized Yb-MOFs nanoballs based dual-wavelength responsive photoelectrochemical aptasensor for the simultaneous determination of AFB1 and OTA

Developing an accurate and precise approach for the simultaneous detection of ochratoxin A (OTA) and aflatoxin B1 (AFB1) is significant for food safety surveillance. Herein, a photoelectrochemical sensing platform was constructed based on polycarboxylic ionic liquid functionalized metal-organic framework integrated with gold nanoparticles (Yb-MOFs@AuNPs). Sulfhydryl functionalized hairpin DNA (hDNA) was immobilized on a Yb-MOFs@AuNPs modified glassy carbon electrode (GCE) surface through Au-S bond. After blocking residual active binding sites with BSA, gold nanoparticles-labeled AFB1 aptamer (AuNPs-Apt 1) and gold nanorods-labeled OTA aptamer (AuNRs-Apt 2) were introduced to construct a photoelectrochemical aptasensor for the simultaneous determination of AFB1 and OTA. Due to the surface plasmon resonance effect and the nanometer size effect of gold nanomaterials, the photoelectrochemical aptasensor can output photocurrent responses as being excited with different wavelengths at 520 nm and 808 nm, respectively. When the AFB1 and OTA concentration in the range of 0.001-50.0 ng mL-1, a good linear relationship between the photocurrent difference (ΔI) before and after recognizing targets and the logarithm of AFB1 or OTA concentration was obtained. The detection limits for AFB1 and OTA were 0.40 pg mL-1 and 0.19 pg mL-1, respectively. AFB1 and OTA in corn samples were detected simultaneously by the photoelectrochemical aptasensor.

Photoelectrochemical aptasensing with methylene blue filled Ni-MOFs nanocomposite by spatial confinement for microcystin-LR detection

Microcystin LR (MC-LR) is a hazardous cyanotoxin produced by cyanobacteria during freshwater eutrophication, which can cause liver cancer. Here, a photoelectrochemical (PEC) aptasensor based on methylene blue (MB)-loaded Ni-MOF composite (Ni-MOF/MB) with spatial confinement was constructed for the sensitive detection of MC-LR. Ni-MOF with two-dimensional sheet structure was prepared via a liquid-liquid interface synthesis method with environmental-friendly solvent and milder reaction conditions. Benefiting from the uniform pore size, Ni-MOF acted as reaction platform to anchor the photosensitive molecule MB. The electron donor, ascorbic acid (AA), was produced by alkaline phosphatase (ALP) loaded on DNA strand catalyzing ascorbic acid phosphate. The generated AA was absorbed by Ni-MOF/MB, thereby effectively improving the utilization of AA and avoiding the external environment interferences to enlarge the photocurrent of MB. For analysis, ALP-labeled aptamer can specifically recognize MC-LR by forming a complex to strip from aptasensor, thus leading to a  decreased photocurrent. The developed PEC aptasensor offered a linear range of 10 fM-100 pM with a detection limit of 6 fM. It was successfully employed for detecting MC-LR in farm water and fish meat, and the results were validated by ultrahigh-performance liquid chromatography-mass spectrometry. This method presents a new idea of MOF-limited domain for PEC aptasensing.

Portable Visual Photoelectrochemical Biosensor Based on a MgTi2O5/CdSe Heterojunction and Reversible Electrochromic Supercapacitor for Dual-Modal Cry1Ab Protein Detection

Reversible electrochromic supercapacitors (ESCs) have attracted considerable interest as visual display screens. The use of ESCs in combination with a photoelectrochemical (PEC) biosensor promises to improve the detection efficiency. Herein, a visual PEC biosensor is developed by introducing a circuit module between a PEC-sensing platform (PSP) and a reversible ESC for Cry1Ab protein detection. In PSP, a type II MgTi2O5/CdSe heterojunction effectively drives charge separation by their cross-matched band gap structures, generating an amplified photocurrent. Next, the circuit module is designed to connect the PSP and ESC, realizing the signal conversion from photocurrent to voltage. ESC, as a visual display screen, produces reversible color changes with different voltages. As the concentration of Cry1Ab increases, the photocurrent decreases due to the specific binding between the aptamer and Cry1Ab in PSP, while the color of the reversible ESC changes from green to blue. To improve the integrity of the device, a portable PEC biosensor is further constructed via three-dimensional printing for dual-modal Cry1Ab protein detection, thus collecting both PEC and visual signals. The linear ranges are 0.3-3000 ng mL-1 for PEC mode and 1-1000 ng mL-1 for visual mode. This work presents a portable, efficient, sensitive, and visualized detection system, providing an important reference for practical visualization applications.

Strategies to control mycotoxins and toxigenic fungi contamination by nano-semiconductor in food and agro-food: a review

Mycotoxins are toxic secondary metabolites generated from toxigenic fungi in the contaminated food and agro-food, which have been regarded as a serious threat to the food safety and human health. Therefore, the control of mycotoxins and toxigenic fungi contamination is of great significance and has attracted the increasing attention of researchers. As we know, nano-semiconductors have many unique properties such as large surface area, structural stability, good biocompatibility, excellent photoelectrical properties, and low cost, which have been developed and applied in many research fields. Recently, nano-semiconductors have also been promisingly applied in mitigating or controlling mycotoxins and toxigenic fungi contaminations in food and agro-food. In this review, the type, occurrence, and toxicity of main mycotoxins in food and agro-food were introduced. Then, a variety of strategies to mitigate the mycotoxin contamination based on nano-semiconductors involving mycotoxins detection, inhibition of toxigenic fungi, and mycotoxins degradation were summarized. Finally, the outlook, opportunities, and challenges have prospected in the future for the mitigation of mycotoxins and toxigenic fungi based on nano-semiconductors.

Recent progress in optical and electrochemical aptasensor technologies for detection of aflatoxin B1

AFB1 (Aflatoxin B1) contamination is becoming a global concern issue due to its extraordinary occurrence, severe toxicity, as well as the great influence on the economic losses, food safety and environment. Therefore, it is desirable to develop novel analytical techniques for simple, rapid, accurate, and even point-of-care testing of AFB1. Fortunately, aptamer, considered as a new generation bioreceptor and even superior to classic antibody and enzyme, has been emerged remarkable application in food hazards detection. Correspondingly, aptasensors have been well-established toward AFB1 determination with outstanding performance. In this article, we first discuss and summarize the recent progress in optical and electrochemical aptasensors to monitor AFB1 over the past three years. In particular, the embedding of advanced nanomaterials for their improved analytical performance is highlighted. Furthermore, the critical analysis on various signal transduction strategies for aptasensors construction is discussed. Finally, we reveal the challenges and provide our opinion in future opportunities for aptasensor development.

Electrochemical Determination of Hazardous Herbicide Diuron Using MWCNTs-CS@NGQDs Composite-Modified Glassy Carbon Electrodes

Diuron (DU) abuse in weed removal and shipping pollution prevention always leads to pesticide residues and poses a risk to human health. In the current research, an innovative electrochemical sensor for DU detection was created using a glassy carbon electrode (GCE) that had been modified with chitosan-encapsulated multi-walled carbon nanotubes (MWCNTs-CS) combined with nitrogen-doped graphene quantum dots (NGQDs). The NGQDs were prepared by high-temperature pyrolysis, and the MWCNTs-CS@NGQDs composite was further prepared by ultrasonic assembly. TEM, UV-Vis, and zeta potential tests were performed to investigate the morphology and properties of MWCNTs-CS@NGQDs. CV and EIS measurements revealed that the assembly of MWCNTs and CS improved the electron transfer ability and effective active area of MWCNTs. Moreover, the introduction of NGQDs further enhanced the detection sensitivity of the designed sensor. The MWCNTs-CS@NGQDs/GCE electrochemical sensor exhibited a wide linear range (0.08~12 μg mL-1), a low limit of detection (0.04 μg mL-1), and high sensitivity (31.62 μA (μg mL-1)-1 cm-2) for DU detection. Furthermore, the sensor demonstrated good anti-interference performance, reproducibility, and stability. This approach has been effectively employed to determine DU in actual samples, with recovery ranges of 99.4~104% in river water and 90.0~94.6% in soil. The developed electrochemical sensor is a useful tool to detect DU, which is expected to provide a convenient and easy analytical technique for the determination of various bioactive species.

Advances in aptamers, and application of mycotoxins detection: A review

Mycotoxin contamination in food products can easily cause serious health hazards and economic losses to human beings. How to accurately detect and effectively control mycotoxin contamination has become a global concern. Mycotoxins conventional detection techniques e.g; ELISA, HPLC, have limitations like, low sensitivity, high cost and time-consuming. Aptamer-based biosensing technology has the advantages of high sensitivity, high specificity, wide linear range, high feasibility, and non-destructiveness, which overcomes the shortcomings of conventional analysis techniques. This review summarizes the sequences of mycotoxin aptamers that have been reported so far. Based on the application of four classic POST-SELEX strategies, it also discusses the bioinformatics-assisted POST-SELEX technology in obtaining optimal aptamers. Furthermore, trends in the study of aptamer sequences and their binding mechanisms to targets is also discussed. The latest examples of aptasensor detection of mycotoxins are classified and summarized in detail. Newly developed dual-signal detection, dual-channel detection, multi-target detection and some types of single-signal detection combined with unique strategies or novel materials in recent years are focused. Finally, the challenges and prospects of aptamer sensors in the detection of mycotoxins are discussed. The development of aptamer biosensing technology provides a new approach with multiple advantages for on-site detection of mycotoxins. Although aptamer biosensing shows great development potential, still some challenges and difficulties are there in practical applications. Future research need high focus on the practical applications of aptasensors and the development of convenient and highly automated aptamers. This may lead to the transition of aptamer biosensing technology from laboratory to commercialization.

Synergistic Signal Amplification-Initiated Innovative Self-Powered Photoelectrochemical Aptasensing: An Ingenious Photocathode Activated by the High-Light-Harvesting Photoanode

Exploiting ingenious photoelectrodes and innovative signal amplification strategies has the potential to achieve high sensitivity in self-powered cathodic photoelectrochemical (PEC) analysis. In this work, a novel self-powered PEC sensing platform was constructed by integrating a synergistic signal amplification of an ingenious photocathode with a high light-harvesting photoanode. In the dual photoelectrode-based PEC system, the amplified photocurrent signals were induced by a synergistic enhancement: (1) the photocurrent of the BiOBr photocathode was improved by the incorporation of nitrogen-doped graphene; (2) the photocurrent of the self-powered sensor was activated by the high-light-harvesting Bi₂S₃-C₃N₄ photoanode. Subsequently, the rational mechanism for synergistic signal amplification was investigated. For the construction of the sensing interface, an aptamer was introduced as the recognition element to specifically capture the streptomycin (STR) target. Under optimal conditions, the constructed self-powered aptasensor has the merits of good linear range (1 × 10^-11 to 5 × 10^-7 M), acceptable limit of detection (1.18 × 10^-12 M), and excellent stability and selectivity for STR detection. Additionally, the proposed self-powered aptasensor showed acceptable accuracy for the detection of STR in water. Hopefully, this might stimulate more interest in designing and constructing novel platforms for exquisite photocathodic monitoring of various contaminants in the environment.

Dual-quenching effects of methylene blue on the luminophore and co-reactant: Application for electrochemiluminescent-electrochemical ratiometric zearalenone detection

Methylene blue (MB) is a common multifunctional indicator, which can be applied as a quencher for electrochemiluminescence (ECL) analysis as well as a classical redox probe. Although it is relatively prevalent for MB to study the mechanism with Ru-based luminophores in ECL systems, there are few studies on the effects between MB and co-reactants. In this work, we proposed the first investigation of MB on the luminophore and co-reactant of the self-enhanced ECL composites (nitrogen-doped graphene quantum dots on Ru(bpy)₃²⁺-doped silica nanoparticles, NGQDs-Ru@SiO₂), respectively. The relatively narrow ECL spectrum of luminophore (Ru@SiO₂) and the suitable ultraviolet-visible absorption spectrum of MB led to the ECL resonance energy transfer between them, meanwhile the appropriate energy levels among them facilitated the electron transfer, resulting in a decreased ECL signal (quench mode I). Additionally, the co-reactant (NGQDs) was prone to π-π conjugation with MB due to its abundant π-electrons, which reduced the concentration of NGQDs' intermediates and triggered a weakened ECL signal (quench mode II). Therefore, the dual-quenching effects are ingeniously integrated and designed in one ECL-electrochemical (ECL-EC) ratiometric aptasensor for zearalenone detection, for demonstrating its efficacy in enhancing the sensitivity, which is 4.8-fold higher than Ru@SiO₂ alone. This innovative ratiometric aptasensor achieved a relatively wide linear range from 1.0 × 10^-15 to 5.0 × 10^-8 g mL^-1, and obtained a low detection limit of 8.5 × 10^-16 g mL^-1. Our proposed dual-quenching interactions between MB and NGQDs-Ru@SiO₂ will open a new prospective for ECL-EC ratiometric aptasensor, which further broaden the application in sensitive and precise analysis of mycotoxins.

Engineering the Signal Transduction between CdTe and CdSe Quantum Dots for in Situ Ratiometric Photoelectrochemical Immunoassay of Cry1Ab Protein

Controllable modulation of a response mode is extremely attracting to fabricate biosensor with programmable analytical performances. Here, we reported a proof-of-concept ratiometric photoelectrochemical (PEC) immunoassay of Cry1Ab protein based on the signal transduction regulation at the sensing interface. A sandwich-type PEC structure was designed so that gold nanorods sensitized quantum dots to fix primary antibody (Au NRs/QDs-Ab₁) and methylene blue sensitized QDs to combine a second antibody (MB/QDs-Ab₂), which served as photoelectric substrate and signal amplifier, respectively. Unlike common recognition element, such a sandwich-type PEC structure allowed for the in situ generation of two specific response signals. For analysis, Cry1Ab captured by Au NRs/QDs-Ab₁ led to a decreased photocurrent (I_Cry1Ab), while the subsequently anchored MB/QDs-Ab₂ produced another photocurrent (I_MB). Noteworthy, by taking advantage of the different energy band gaps of QDs, varying locations of CdTe and CdSe QDs could realize different signal transduction strategies (i.e., Mode 1 and Mode 2). Investigations on data analysis of I_Cry1Ab and I_MB via different routes demonstrated the superior analytical performances of ratiometry (Mode 1). Consequently, the ratiometric PEC immunosensor offered a linear range of 0.01-100 ng mL^-1 with a detection limit of 1.4 pg mL^-1. This work provides an efficient strategy for in situ collection of multiple photocurrents to design ratiometric PEC sensors.

A reusable and sensitive electrochemical sensor for determination of idarubicin in environmental and biological samples based on NiFe2O4 nanospheres anchored N-doped graphene quantum dots composite; an electrochemical and molecular docking investigation

An ultrasensitive and selective voltammetric sensor with ultra-trace level detection limit is introduced for idarubicin (IDA) determination in real samples. The as-synthesized nanocomposite was characterized by several techniques, including Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), Raman spectroscopy, Energy-dispersive X-ray spectroscopy (EDX), and Field emission scanning electron microscopy (FE-SEM). The electrocatalytic performance of the developed electrode was observed by cyclic voltammetry (CV), differential pulse voltammetry (DPV), electrochemical impedance spectroscopy (EIS), and chronoamperometry. The limit of detection (LOD) of the developed sensor for idarubicin is 1.0 nM, and the response is found to be in the dynamic concentration range of 0.01-1.9 μmol/L in a Britton-Robinson buffer (B-R, pH = 6.0). Moreover, the fabricated electrode illustrated high selectivity with good repeatability and reproducibility for diagnosing idarubicin as an anthracycline antileukemic drug. Furthermore, to evaluate the validity of the recommended method, three real samples, including human plasma, urine, and water samples, were analyzed with satisfactory recovery and compared with high-performance liquid chromatography (HPLC). The minor groove-binding mode of interaction was also supported by docking simulation studies, emphasizing that IDA can bind to ds-DNA preferably and confirmed experimental results. The reduced assay time and the possibility of measuring a single sample with another anticancer drug without any interference are significant advantages compared to the HPLC. The developed and validated sensor could be a valuable point-of-care diagnostic tool for IDA quantification in patients.

Evanescent Wave Optical-Fiber Aptasensor for Rapid Detection of Zearalenone in Corn with Unprecedented Sensitivity

Zearalenone (ZEN) is a common mycotoxin pollutant found in agricultural products. Aptamers are attractive recognition biomolecules for the development of mycotoxin biosensors. Even though numerous aptasensors have been reported for the detection of ZEN in recent years, many of them suffer from problems including low sensitivity, low specificity, tedious experimental steps, high-cost, and difficulty of automation. We report here the first evanescent wave optical-fiber aptasensor for the detection of ZEN with unprecedented sensitivity, high specificity, low cost, and easy of automation. In our aptasensor, a 40-nt ZEN-specific aptamer (8Z₃₁) is covalently immobilized on the fiber. The 17-nt fluorophore Cy5.5-labeled complementary DNA strand and ZEN competitively bind with the aptamer immobilized on the fiber, enabling the signal-off fluorescent detection of ZEN. The coating of Tween 80 enhanced both the sensitivity and the reproducibility of the aptasensor. The sensor was able to detect ZEN spiked-in the corn flour extract with a semilog linear detection range of 10 pM-10 nM and a limit of detection (LOD, S/N = 3) of 18.4 ± 4.0 pM (equivalent to 29.3 ± 6.4 ng/kg). The LOD is more than 1000-fold lower than the maximum ZEN residue limits set by China (60 μg/kg) and EU (20 μg/kg). The sensor also has extremely high specificity and showed negligible cross-reactivity to other common mycotoxins. In addition, the sensor was able to be regenerated for 28 times, further decreasing its cost. Our sensor holds great potential for practical applications according to its multiple compelling features.

Application of Nanomaterials for Coping with Mycotoxin Contamination in Food Safety: From Detection to Control

Mycotoxins, which are toxic secondary metabolites produced by fungi, are harmful to humans. Mycotoxin-induced contamination has drawn attention worldwide. Consequently, the development of reliable and sensitive detection methods and high-efficiency control strategies for mycotoxins is important to safeguard food industry safety and public health. With the rapid development of nanotechnology, many novel nanomaterials that provide tremendous opportunities for greatly improving the detection and control performance of mycotoxins because of their unique properties have emerged. This review comprehensively summarizes recent trends in the application of nanomaterials for detecting mycotoxins (fluorescence, colorimetric, surface-enhanced Raman scattering, electrochemical, and point-of-care testing) and controlling mycotoxins (inhibition of fungal growth, mycotoxin absorption, and degradation). These detection methods possess the advantages of high sensitivity and selectivity, operational simplicity, and rapidity. With research attention on the control of mycotoxins and the gradual excavation of the properties of nanomaterials, nanomaterials are also employed for the inhibition of fungal growth, mycotoxin absorption, and mycotoxin degradation, and impressive controlling effects are obtained. This review is expected to provide the readers insight into this state-of-the-art area and a reference to design nanomaterials-based schemes for the detection and control of mycotoxins.

Label-free ratiometric homogeneous electrochemical aptasensor based on hybridization chain reaction for facile and rapid detection of aflatoxin B1 in cereal crops

Aflatoxin B1 (AFB1) contamination has raised global concerns in agricultural and food industry; thus, sensitive, accurate and rapid AFB1 sensors are essential in many circumstances. Herein, we developed a label-free and immobilization-free ratiometric homogeneous electrochemical aptasensor based on hybridization chain reaction (HCR) for facile and rapid determination of AFB1. Methylene blue (MB) and ferrocene (Fc) were used as label-free probes to produce a response signal (I_MB) and a reference signal (I_Fc) in solution phase, respectively. The ratio of I_MB/I_Fc was used as a yardstick to quantify AFB1. HCR was exploited to enlarge the intensity of I_MB as well as ratiometric signal. By combining label-free homogeneous assay and ratiometric strategy, the resulting aptasensor offered sensitive, rapid, and reliable determinations of AFB1 with a detection limit of 38.8 pg mL^-1. The aptasensor was then used to determine AFB1 in cereal samples with comparable reliability as HPLC-MS.

Recent advances in the highly sensitive determination of zearalenone residues in water and environmental resources with electrochemical biosensors

Zearalenone (ZEN), a significant class of mycotoxin which is considered as a xenoestrogen, permits, similar to natural estrogens, it's binding to the receptors of estrogen resulting in various reproductive diseases especially, hormonal misbalance. ZEN has toxic effects on human and animal health as a result of its teratogenicity, carcinogenicity, mutagenicity, nephrotoxicity, genotoxicity, and immunotoxicity. To ensure water and environmental resources safety, precise, rapid, sensitive, and reliable analytical and conventional methods can be progressed for the determination of toxins such as ZEN. Different selective nanomaterial-based compounds are used in conjunction with different analytical detection approaches to achieve this goal. The current review demonstrates the state-of-the-art advances of nanomaterial-based electrochemical sensing assays including various sensing, apta-sensing and, immunosensing studies to the highly sensitive determination of various ZEN families. At first, a concise study of the occurrence, structure, toxicity, legislations, and distribution of ZEN in monitoring has been performed. Then, different conventional and clinical techniques and procedures to sensitive and selective sensing techniques have been reviewed and the efficient comparison of them has been thoroughly discussed. This study has also summarized the salient features and the requirements for applying various sensing and biosensing platforms and diverse immobilization techniques in ZEN detection. Finally, we have defined the performance of several electrochemical sensors applying diverse recognition elements couples with nanomaterials fabricated using various recognition elements coupled with nanomaterials (metal NPs, metal oxide nanoparticles (NPs), graphene, and CNT) the issues limiting development, and the forthcoming tasks in successful construction with the applied nanomaterials.

Dual-Enzyme-Based Signal-Amplified Aptasensor for Zearalenone Detection by Using CRISPR-Cas12a and Nt.AlwI

Zearalenone (ZEN) is harmful to animals and human beings, so it is very important to develop a rapid and sensitive method for the detection of ZEN. In this paper, we proposed a novel ZEN-monitoring method using two aptamers as recognition elements and EnGen LbaCas12a and Nt.AlwI nicking endonuclease as signal amplifiers. When ZEN was present, it bound to the aptamer Z0 and, Z1 was released into solution. The solution was then separated and the Nt.AlwI enzyme was added in order to form a nicking-enzyme cycle, thereby producing large amounts of the ssDNA Z3 for 30 min. The Z3 formed a CRISPR-Cas12a-Z3 complex with CRISPR-Cas12a, activated the trans-cleavage ability of Cas12a, cleaved the Quenched Reporter for 20 min, and underwent fluorescence recovery. The aptasensor was able to sensitively detect ZEN in the linear range of 1–1000 pg/mL, with a detection limit as low as 0.213 pg/mL. The detection time lasted for 2 h. Additionally, this detection technology can also be used to monitor other hazards.

Dual-ratiometric electrochemical aptasensor enabled by programmable dynamic range: Application for threshold-based detection of aflatoxin B1

Aptamer-based sensor with high-specificity typically has a fixed linear range due to the host-guest binding. To expand the dynamic range for multiple scenarios, we report here a dual-ratiometric electrochemical aptasensor that integrates two aptamer profiles with varied affinity into a single sensing interface for aflatoxin B1 (AFB1) detection. Using functional aptamer as recognition element and generator of signals, we fabricate the dual-ratiometric aptasensor with anthraquinone loaded reduced graphene oxide (AQ-rGO), methylene blue labeled hairpin DNA (MB-DNA), and ferrocene labeled linear aptamer (Fc-apt), using MB and Fc probes to work in tandem while AQ as reference. The current of Fc (I_Fc) is used to detect the low-concentration analyte, and that of MB (I_MB) varies when the concentration of AFB1 reaches a threshold. The threshold switch for I_MB could be tuned by engineering the quantity ratio of Fc-apt and MB-DNA (a ratio of 1:1 is used here). The aptasensor can rapidly achieve the positive (+)/negative (-) detection of AFB1 with a threshold concentration of 10 pg mL^-1, while the quantitative detection employs the ratio of current of AQ, MB, and Fc (i.e., I_AQ/I_MB and I_AQ/I_Fc) as yardsticks, offering two linear ranges of 10-10⁶ and 10^-2-5 × 10⁴ pg mL^-1, respectively. The aptasensor is successfully used to monitor the amount of AFB1 in a 7-days mildew process of peanut. Such a protocol opens a new way for the design of sensors with the programmable linear range in the advanced biological and chemical sensing.

Aptasensors for mycotoxins in foods: Recent advances and future trends

Mycotoxin contamination in foods has posed serious threat to public health and raised worldwide concern. The development of simple, rapid, facile, and cost-effective methods for mycotoxin detection is of urgent need. Aptamer-based sensors, abbreviated as aptasensors, with excellent recognition capacity to a wide variety of mycotoxins have attracted ever-increasing interest of researchers because of their simple fabrication, rapid response, high sensitivity, low cost, and easy adaptability for in situ measurement. The past few decades have witnessed the rapid advances of aptasensors for mycotoxin detection in foods. Therefore, this review first summarizes the reported aptamer sequences specific for mycotoxins. Then, the recent 5-year advancements in various newly developed aptasensors, which, according to the signal output mode, are divided into electrochemical, optical and photoelectrochemical categories, for mycotoxin detection are comprehensively discussed. A special attention is taken on their strengths and limitations in real-world application. Finally, the current challenges and future perspectives for developing novel highly reliable aptasensors for mycotoxin detection are highlighted, which is expected to provide powerful references for their thorough research and extended applications. Owing to their unique advantages, aptasensors display a fascinating prospect in food field for safety inspection and risk assessment.

Carbon-Based Nanocomposite Smart Sensors for the Rapid Detection of Mycotoxins

Carbon-based nanomaterials have become the subject of intensive interest because their intriguing physical and chemical properties are different from those of their bulk counterparts, leading to novel applications in smart sensors. Mycotoxins are secondary metabolites with different structures and toxic effects produced by fungi. Mycotoxins have low molecular weights and highly diverse molecular structures, which can induce a spectrum of biological effects in humans and animals even at low concentrations. A tremendous amount of biosensor platforms based on various carbon nanocomposites have been developed for the determination of mycotoxins. Therefore, the contents of this review are based on a balanced combination of our own studies and selected research studies performed by academic groups worldwide. We first address the vital preparation methods of biorecognition unit (antibodies, aptamers, molecularly imprinted polymers)-functionalized carbon-based nanomaterials for sensing mycotoxins. Then, we summarize various types of smart sensors for the detection of mycotoxins. We expect future research on smart sensors to show a significant impact on the detection of mycotoxins in food products.

Photoelectrochemical detection for 3,3',4,4'-tetrachlorobiphenyl in fish based on synergistic effects by Schottky junction and sensitization

In this study, a novel signal amplification strategy on photoelectrochemical (PEC) aptasensor was designed for high-sensitivity and -selectivity detection of 3,3',4,4'-tetrachlorobiphenyl (PCB77) on the basis of Schottky junction and sensitization. First, the Schottky barrier not only provided an electron-transfer irreversible passage from CuO to Au Nanoparticles (NPs) but also generated excellent local surface plasmon resonance between CuO and Au NPs, thus improving the efficiency of charge separation and light absorption. Second, to further improve the response of the PEC aptasensor under the action of the sensitization, the complementary-DNA-functionalized CdS quantum dots were introduced onto the surface of CuO/Au NPs via hybridization of the target aptamer. The PEC aptasensor exhibited a low detection limit of 17.3 pg L^-1, and a wide linear response was shown at a range of 0.2-220 ng L^-1 depending on the variation of photocurrent before and after incubation.

Multiple fluorescence immunoassay for the simultaneous detection of Zearalenone and Ochratoxin A

A sensitive and accurate multiple fluorescence immunoassay for the simultaneous quantitative detection of Zearalenone (ZEN) and Ochratoxin A (OTA) in single spot based on multicolor quantum dots (QDs) labeling was developed for the first time. Two kinds of ZnCdSe/ZnS (core/shell) QDs with maximum emission wavelengths at 520 nm (green) and 610 nm (orange-red) were selected as marking materials, respectively. The anti-ZEN-mAb-QDs and anti-OTA-mAb-QDs were designed as the immune fluorescent probes. Fluorescence was measured at the same excitation wavelength and two different emission wavelengths to determine each target. The procedure for QDs-based multiple fluorescence labeled immunosorbent assay (M-FLISA) was developed. The 50% inhibition concentrations (IC₅₀) of ZEN and OTA were 0.034 and 1.175 ng/mL. Moreover, the limits of detection (LOD) for the simultaneous determination were 0.0239 and 2.339 ng/g for ZEN and OTA in maize, respectively. In addition, the recoveries ranged from 93.15 to 101.90% for ZEN and from 95.29 to 102.43% for OTA, with the coefficient variation (CV) of 2.70-8.86% and 3.51-6.22% respectively. There was good consistency between the M-FLISA and high performance liquid chromatography (HPLC) results, which confirmed that the M-FLISA was suitable for the simultaneous quantitative detection of various mycotoxins.

g-C3N4/Fe3O4 Nanocomposites as Adsorbents Analyzed by UPLC-MS/MS for Highly Sensitive Simultaneous Determination of 27 Mycotoxins in Maize: Aiming at Increasing Purification Efficiency and Reducing Time

According to known studies, numerous mycotoxins have been found simultaneously in foods and have a certain expansion toxicity, so the simultaneous detection of multiple mycotoxins is absolutely critical. In this article, multifunctional magnetic g-C₃N₄/Fe₃O₄ nanocomposites have been fabricated to employ as modified QuEChERS adsorbents. In addition, they were also used in conjunction with ultrahigh-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS), an accurate quantitative approach, to analyze 27 mycotoxins in maize. The improved method not only has a powerful adsorption effect on the complex matrix by g-C₃N₄/Fe₃O₄ but also enables magnetic separation from the sample solution. Experiments proved that this method can exhibit good linearity under the appropriate and optimal external environment (r² ≥ 0.9954), high sensitivity (the threshold of detection limit is 0.0004-0.6226 μg kg^-1, and the threshold of quantification limit is 0.0014-2.0753 μg kg^-1), adequate recoveries (77.81-115.21%), and excellent repeatability (with a threshold of intraday precision of 1.5-10.8% and interday precision in the range of 2.9-12.5%). In practice this method has been used to evaluate a variety of mycotoxins in maize specimens, and certain actual outcomes have been achieved.

A FRET aptasensor for sensitive detection of aflatoxin B1 based on a novel donor-acceptor pair between ZnS quantum dots and Ag nanocubes

Aflatoxin B1 (AFB1) is one of the most carcinogenic chemicals. A novel fluorescence resonance energy transfer (FRET) sensor based on aptamer recognition technology is proposed for the sensitive detection of AFB1 in moldy peanuts using Ag nanocubes as energy acceptors and ZnS quantum dots (QDs) as energy donors. Compared to the traditional FRET system based on an Au quencher, Ag nanocubes can not only quench the fluorescence of aptamer modified ZnS QDs, but are also inexpensive. In addition, compared with heavy metal QDs, ZnS QDs are environmentally friendly, have excellent photochemical properties, and are ideal energy donors. Without Ag nanocubes, the aptamer modified ZnS QDs emits blue fluorescence under an ultraviolet lamp. Because the emission spectrum of ZnS and the absorption spectrum of Ag nanocubes meet the requirements of FRET, the fluorescence quenching of ZnS QDs is realized. Nevertheless, with AFB1, the specific binding of aptamer and complementary chain makes the ZnS QDs break away from the Ag nanocubes, which leads to the fluorescence recovery of the ZnS QDs. Under the optimized detection conditions, the linear range of AFB1 was 5 pg mL^-1 to 300 ng mL^-1, and there was no obvious reaction with other similar mycotoxins. According to S/N = 3, the detection limit of AFB1 was 2.67 pg mL^-1. The detection of AFB1 in peanut samples shows that the new FRET system can successfully be applied in the future to agricultural products.

Direct and Competitive Optical Grating Immunosensors for Determination of Fusarium Mycotoxin Zearalenone

Novel optical waveguide lightmode spectroscopy (OWLS)-based immunosensor formats were developed for label-free detection of Fusarium mycotoxin zearalenone (ZON). To achieve low limits of detection (LODs), both immobilised antibody-based (direct) and immobilised antigen-based (competitive) assay setups were applied. Immunoreagents were immobilised on epoxy-, amino-, and carboxyl-functionalised sensor surfaces, and by optimising the immobilisation methods, standard sigmoid curves were obtained in both sensor formats. An outstanding LOD of 0.002 pg/mL was obtained for ZON in the competitive immunosensor setup with a dynamic detection range between 0.01 and 1 pg/mL ZON concentrations, depending on the covalent immobilisation method applied. This corresponds to a five orders of magnitude improvement in detectability of ZON relative to the previously developed enzyme-linked immonosorbent assay (ELISA) method. The selectivity of the immunosensor for ZON was demonstrated with structural analogues (α-zearalenol, α-zearalanol, and β-zearalanol) and structurally unrelated mycotoxins. The method was found to be applicable in maize extract using acetonitrile as the organic solvent, upon a dilution rate of 1:10,000 in buffer. Thus, the OWLS immunosensor method developed appears to be suitable for the quantitative determination of ZON in aqueous medium. The new technique can widen the range of sensoric detection methods of ZON for surveys in food and environmental safety assessment.

An overview and future prospects on aptamers for food safety

Introduction

Many bacteria are responsible for infections in humans and plants, being found in vegetables, water, and medical devices. Most bacterial detection methods are time-consuming and take days to give the result. Aptamers are a promising alternative for a quick and reliable measurement technique to detect bacteria present in food products. Selected aptamers are DNA or RNA oligonucleotides that can bind with bacteria or other molecules with affinity and specificity for the target cells by the SELEX or cell-SELEX technique. This method is based on some rounds to remove the non-ligand oligonucleotides, leaving the aptamers specific to bind to the selected bacteria. Compared with conventional methodologies, the detection approach using aptamers is a rapid, low-cost form of analysis.

Objective

This review summarizes obtention methods and applications of aptamers in the food industry and biotechnology. Besides, different techniques with aptamers are presented, which enable more effective target detection.

Conclusion

Applications of aptamers as biosensors, or the association of aptamers with nanomaterials, may be employed in analyses by colorimetric, fluorescence, or electrical devices. Additionally, more efficient ways of sample preparation are presented, which can support food safety to provide human health, with a low-cost method for contaminant detection.

Key points • Aptamers are promising for detecting contaminants outbreaks. • Studies are needed to identify aptamers for different targets.