Piperidinium functionalized aryl ether-free polyaromatics as anion exchange membrane for water electrolysers: Performance and durability

Promoting in-situ stability of hydroxide exchange membranes by thermally conductive network for durable water electrolysis

Hydroxide exchange membrane (HEM) water electrolysis is promising for green hydrogen production due to its low cost and excellent performance. However, HEM often has insufficient stability in strong alkaline solutions, particularly under in-situ electrolysis operation conditions, hindering its commercialization. In this study, we discover that the in-situ stability of HEM is primarily impaired by the locally accumulated heat in HEM due to its low thermal conductivity. Accordingly, we propose highly thermally conductive HEMs with an efficient three-dimensional (3D) thermal diffusion network to promote the in-situ stability of HEM for water electrolysis. Based on the 3D heat conductive network, the thermal conductivity of polymeric HEM is boosted by 32 times and thereby reduce the HEM temperature by up to 4.9 °C in a water electrolyzer at the current density of 1 A cm-2. Thus, the thermally conductive HEM exhibits negligible degradation after 20,000 start/stop cycles and reduces the degradation rate by 6 times compared to the pure polymeric HEM in a water electrolyzer. This study manifests the significance of thermal conductivity of HEM on the durability of water electrolysis, which provides guidelines on the rational design of highly durable HEMs in practical operation conditions for water electrolysis, fuel cells, and beyond.

Engineering Robust Triazine Crosslinked and Pyridine Capped Anion Exchange Membrane for Advanced Water Electrolysis

Exploring high-performance anion exchange membranes (AEM) for water electrolyzers (AEMWEs) is significant for green hydrogen production. However, the current AEMWEs are restricted by the poor mechanical strength and low OH- conductivity of AEMs, leading to the low working stability and low current density. Here, we develop a robust AEM with polybiphenylpiperidium network by combining the crosslinking with triazine and the capping with pyridine for advanced AEMWEs. The AEM exhibits an excellent mechanical strength (79.4 MPa), low swelling ratio (19.2 %), persistent alkali stability (≈5,000 hours) and high OH- conductivity (247.2 mS cm-1) which achieves the state-of-the-art AEMs. Importantly, when applied in AEMWEs, the corresponding electrolyzer equipped with commercial nickel iron and nickel molybdenum catalysts obtained a current density of up to 3.0 A cm-2 at 2 V and could be stably operated ~430 h at a high current density of 1.6 A cm-2, which exceeds the most of AEMWEs. Our results suggest that triazine crosslinking and pyridine capping can effectively improve the overall performance of the AEMWEs.

High-Performance Anion Exchange Membrane Water Electrolyzers Enabled by Highly Gas Permeable and Dimensionally Stable Anion Exchange Ionomers

Designing suitable anion exchange ionomers is critical to improving the performance and in situ durability of anion exchange membrane water electrolyzers (AEMWEs) as one of the promising devices for producing green hydrogen. Herein, highly gas-permeable and dimensionally stable anion exchange ionomers (QC6xBA and QC6xPA) are developed, in which bulky cyclohexyl (C6) groups are introduced into the polymer backbones. QC650BA-2.1 containing 50 mol% C6 composition shows 16.6 times higher H2 permeability and 22.3 times higher O2 permeability than that of QC60BA-2.1 without C6 groups. Through-plane swelling of QC650BA-2.1 decreases to 12.5% from 31.1% (QC60BA-2.1) while OH- conductivity slightly decreases (64.9 and 56.2 mS cm-1 for QC60BA-2.1 and QC650BA-2.1, respectively, at 30 °C). The water electrolysis cell using the highly gas permeable QC650BA-2.1 ionomer and Ni0.8Co0.2O in the anode catalyst layer achieves two times higher performance (2.0 A cm-2 at 1.69 V, IR-included) than those of the previous cell using in-house ionomer (QPAF-4-2.0) (1.0 A cm-2 at 1.69 V, IR-included). During 1000 h operation at 1.0 A cm-2, the QC650BA-2.1 cell exhibits nearly constant cell voltage with a decay rate of 1.1 µV h-1 after the initial increase of the cell voltage, proving the effectiveness of the highly gas permeable and dimensionally stable ionomer in AEMWEs.

Separators and Membranes for Advanced Alkaline Water Electrolysis

Traditionally, alkaline water electrolysis (AWE) uses diaphragms to separate anode and cathode and is operated with 5-7 M KOH feed solutions. The ban of asbestos diaphragms led to the development of polymeric diaphragms, which are now the state of the art material. A promising alternative is the ion solvating membrane. Recent developments show that high conductivities can also be obtained in 1 M KOH. A third technology is based on anion exchange membranes (AEM); because these systems use 0-1 M KOH feed solutions to balance the trade-off between conductivity and the AEM's lifetime in alkaline environment, it makes sense to treat them separately as AEM WE. However, the lifetime of AEM increased strongly over the last 10 years, and some electrode-related issues like oxidation of the ionomer binder at the anode can be mitigated by using KOH feed solutions. Therefore, AWE and AEM WE may get more similar in the future, and this review focuses on the developments in polymeric diaphragms, ion solvating membranes, and AEM.

High Free Volume Polyelectrolytes for Anion Exchange Membrane Water Electrolyzers with a Current Density of 13.39 A cm-2 and a Durability of 1000 h

The rational design of the current anion exchange polyelectrolytes (AEPs) is challenging to meet the requirements of both high performance and durability in anion exchange membrane water electrolyzers (AEMWEs). Herein, highly-rigid-twisted spirobisindane monomer is incorporated in poly(aryl-co-aryl piperidinium) backbone to construct continuous ionic channels and to maintain dimensional stability as promising materials for AEPs. The morphologies, physical, and electrochemical properties of the AEPs are investigated based on experimental data and molecular dynamics simulations. The present AEPs possess high free volumes, excellent dimensional stability, hydroxide conductivity (208.1 mS cm-1 at 80 °C), and mechanical properties. The AEMWE of the present AEPs achieves a new current density record of 13.39 and 10.7 A cm-2 at 80 °C by applying IrO2 and nonprecious anode catalyst, respectively, along with outstanding in situ durability under 1 A cm-2 for 1000 h with a low voltage decay rate of 53 µV h-1 . Moreover, the AEPs can be applied in fuel cells and reach a power density of 2.02 W cm-2 at 80 °C under fully humidified conditions, and 1.65 W cm-2 at 100 °C, 30% relative humidity. This study provides insights into the design of high-performance AEPs for energy conversion devices.

Triptycene Branched Poly(aryl-co-aryl piperidinium) Electrolytes for Alkaline Anion Exchange Membrane Fuel Cells and Water Electrolyzers

Alkaline polymer electrolytes (APEs) are essential materials for alkaline energy conversion devices such as anion exchange membrane fuel cells (AEMFCs) and water electrolyzers (AEMWEs). Here, we report a series of branched poly(aryl-co-aryl piperidinium) with different branching agents (triptycene: highly-rigid, three-dimensional structure; triphenylbenzene: planar, two-dimensional structure) for high-performance APEs. Among them, triptycene branched APEs showed excellent hydroxide conductivity (193.5 mS cm-1 @80 °C), alkaline stability, mechanical properties, and dimensional stability due to the formation of branched network structures, and increased free volume. AEMFCs based on triptycene-branched APEs reached promising peak power densities of 2.503 and 1.705 W cm-2 at 75/100 % and 30/30 % (anode/cathode) relative humidity, respectively. In addition, the fuel cells can run stably at a current density of 0.6 A cm-2 for 500 h with a low voltage decay rate of 46 μV h-1 . Importantly, the related AEMWE achieved unprecedented current densities of 16 A cm-2 and 14.17 A cm-2 (@2 V, 80 °C, 1 M NaOH) using precious and non-precious metal catalysts, respectively. Moreover, the AEMWE can be stably operated under 1.5 A cm-2 at 60 °C for 2000 h. The excellent results suggest that the triptycene-branched APEs are promising candidates for future AEMFC and AEMWE applications.

Cycloaliphatic Quaternary Ammonium Functionalized Poly(oxindole biphenyl) Based Anion-Exchange Membranes for Water Electrolysis: Stability and Performance

Mechanically robust anion-exchange membranes (AEMs) with high conductivity and long-term alkali resistance are needed for water electrolysis application. In this work, aryl-ether free polyaromatics containing isatin moieties were prepared via super acid-catalyzed copolymerization, followed by functionalization with alkaline stable cyclic quaternary ammonium (QA) cationic groups, to afford high performance AEMs for application in water electrolysis. The incorporation of side functional cationic groups (pyrrolidinium and piperidinium) onto a polymer backbone via a flexible alkyl spacer aimed at conductivity and alkaline stability improvement. The effect of cation structure on the properties of prepared AEMs was thoroughly studied. Pyrrolidinium- and piperidinium-based AEMs showed similar electrolyte uptakes and no obvious phase separation, as revealed by SAXS and further supported by AFM and TEM data. In addition, these AEMs displayed high conductivity values (81. 5 and 120 mS cm-1 for pyrrolidinium- and piperidinium-based AEM, respectively, at 80 °C) and excellent alkaline stability after 1 month aging in 2M KOH at 80 °C. Especially, a pyrrolidinium-based AEM membrane preserved 87% of its initial conductivity value, while at the same time retaining its flexibility and mechanical robustness after storage in alkaline media (2M KOH) for 1 month at 80 °C. Based on 1H NMR data, the conductivity loss observed after the aging test is mainly related to the piperidinium degradation that took place, probably via ring-opening Hofmann elimination, alkyl spacer scission and nucleophilic substitution reactions as well. The synthesized AEMs were also tested in an alkaline water electrolysis cell. Piperidinium-based AEM showed superior performance compared to its pyrrolidinium analogue, owing to its higher conductivity as revealed by EIS data, further confirming the ex situ conductivity measurements.

Hydrocarbon Ionomeric Binders for Fuel Cells and Electrolyzers

Ionomeric binders in catalyst layers, abbreviated as ionomers, play an essential role in the performance of polymer-electrolyte membrane fuel cells and electrolyzers. Due to environmental issues associated with perfluoroalkyl substances, alternative hydrocarbon ionomers have drawn substantial attention over the past few years. This review surveys literature to discuss ionomer requirements for the electrodes of fuel cells and electrolyzers, highlighting design principles of hydrocarbon ionomers to guide the development of advanced hydrocarbon ionomers.

Recent Advancements of Polymeric Membranes in Anion Exchange Membrane Water Electrolyzer (AEMWE): A Critical Review

Water electrolysis coupled with renewable energy is one of the principal methods for producing green hydrogen (or renewable hydrogen). Among the different electrolysis technologies, the evolving anion exchange membrane water electrolysis (AEMWE) shows the utmost promise for the manufacture of green hydrogen in an inexpensive way. In the present review, we highlight the most current and noteworthy achievements of AEMWE, which include the advancements in increasing the polymer anionic conductivity, understanding the mechanism of degradation of AEM, and the design of the electrocatalyst. The important issues affecting the AEMWE behaviour are highlighted, and future constraints and openings are also discussed. Furthermore, this review provides strategies for producing dynamic and robust AEMWE electrocatalysts.

Understanding the Effect of Triazole on Crosslinked PPO–SEBS-Based Anion Exchange Membranes for Water Electrolysis

For anion exchange membrane water electrolysis (AEMWE), two types of anion exchange membranes (AEMs) containing crosslinked poly(phenylene oxide) (PPO) and poly(styrene ethylene butylene styrene) (SEBS) were prepared with and without triazole. The impact of triazole was carefully examined. In this work, the PPO was crosslinked with the non-aryl ether-type SEBS to take advantage of its enhanced chemical stability and phase separation under alkaline conditions. Compared to their triazole-free counterpart, the crosslinked membranes made with triazole had better hydroxide-ion conductivity because of the increased phase separation, which was confirmed by X-ray diffraction (XRD) and atomic force microscopy (AFM). Moreover, they displayed improved mechanical and alkaline stability. Under water electrolysis (WE) conditions, a triazole-containing crosslinked PPO–SEBS membrane electrode assembly (MEA) was created using IrO2 as the anode and a Pt/C catalyst as the cathode. This MEA displayed a current density of 0.7 A/cm2 at 1.8 V, which was higher than that of the MEA created with the triazole-free counterpart. Our study indicated that the crosslinked PPO–SEBS membrane containing triazoles had improved chemo-physical and electrical capabilities for WE because of the strong hydrogen bonding between triazole and water/OH−.

Highly Efficient and para-Selective C-H Functionalization of Polystyrene Providing a Versatile Platform for Diverse Applications

Postpolymerization modification of polystyrene (PS) can afford numerous value-added materials with different functions and applications, but it has been hampered by the lack of efficient methods. We report herein a highly efficient and para-selective conversion of the C-H bonds of the aromatic ring of PS into diverse functional groups using a combination of thianthrenation and thio-Suzuki-Miyaura coupling reaction. Notably, the thianthrenation efficiency of PS is as high as 99% and the degree of thianthrenation can be conveniently controlled using stoichiometric tuning of the amount of thianthrene-S-oxide added, resulting in 24-99 mol % thianthrenation. In the subsequent thio-Suzuki-Miyaura coupling reaction, 18 functionalized PS containing various functional groups (-CH₂OH, -OMe, -SMe, -OTBS, -CH₃, -NHBoc, -OCOMe, -CHO, -COMe, -Si(Me)₃, etc.) were successfully prepared with a high degree of functionalization (64-99 mol %). The obtained functionalized PS can be readily converted into diverse functional materials, including solid-phase synthesis resins, aggregation-induced emission fluorophores, as well as ionomer binders and ion-exchange membranes for energy conversion devices. This method imparts diverse functionality onto PS with extremely high efficiency and selectivity, providing a versatile platform to transform existing commodity PS plastics into high-performance materials.

Anion-exchange membrane water electrolyzers and fuel cells

The key components, working management, and operating techniques of anion-exchange membrane water electrolyzers and fuel cells are reviewed for the first time.

Clustered piperidinium-functionalized poly(terphenylene) anion exchange membranes with well-developed conductive nanochannels

Anion exchange membrane fuel cells (AEMFCs) attract considerable attention owing to their high-power density and potential utilization of cheap non-noble metal catalysts. However, anion exchange membranes (AEMs) still face the problems of low conductivity, poor dimensional and chemical stability. To address these issues, AEMs with clustered piperidinium groups and ether-bond-free poly(terphenylene) backbone (3QPAP-x, x = 0.3, 0.4, and 0.5) were designed. Transmission electron microscope results show that the clustered ionic groups are responsible for fabricating well-developed conductive nanochannels and restraining the swelling behavior of the membranes. 3QPAP-0.4 and 3QPAP-0.5 AEMs exhibit higher conductivity (117.5 mS cm^-1, 80 °C) and lower swelling ratio than that of commercial FAA-3-50 (80.4 mS cm^-1, 80 °C). The conductivity of 3QPAP-0.5 only decreased by 10.4% after treating with 1 M NaOH at 80 °C for 720 h. The Hofmann elimination degradation of the cationic groups is restrained by the long flexible alkyl chain between cations. Based on the high performance of 3QPAP-0.5, an H₂-O₂-type AEMFC reaches 291.2 mW cm^-2 (60 °C), which demonstrates that the as-prepared AEMs are promising for application in fuel cells.

Aldol Condensation Versus Superbase-Catalyzed Addition of Ketones to Acetylenes: A Quantum-Chemical and Experimental Study

The mechanism of aldol condensation of ketones in KOH/DMSO superbasic media has been investigated using the B2PLYP(D2)/6-311+G**//B3LYP/6-31+G* quantum-chemical approach. It is found that the interaction of three ketone molecules resulting in the formation of the cyclohex-2-enone structure [isophorone or 3,5-dicyclohexyl-5-methylspiro(5.5)undec-2-en-1-one] is thermodynamically more favorable than the interaction of two, three, or four molecules of ketone, resulting in the formation of linear products of the condensation. The formation of the condensation products with the isophorone skeleton can significantly hinder the cascade reactions of ketones with acetylenes [to afford 6,8-dioxabicyclo(3.2.1)octanes or acylcyclopentenols] promoted by superbases. In particular, the kinetically more preferable reactions of autovinylation of 2-methyl-3-butyn-2-ol and autocondensation of acetone are the reasons why interaction of acetone with acetylene does not lead to the products of the cascade assemblies. The predominant formation of the products of these side reactions is confirmed experimentally.