Removal of chelated heavy metals from aqueous solution: A review of current methods and mechanisms

In-situ groundwater remediation of contaminant mixture of As(III), Cr(VI), and sulfanilamide via electrochemical degradation/transformation using pyrite

Electrochemical advanced oxidation processes (EAOPs) are effective in removing persistent contaminants from groundwater. However, their practical applicability depends significantly on various site-specific characteristics. Therefore, the primary objective of this investigation was to study the feasibility of EAOPs and pyrite, which is a sulfide mineral, to effectively remove the mixture of arsenic (As (III)), chromium (Cr (VI)), and sulfanilamide in groundwater. We conducted a comparison of three systems: (1) EAOP alone, (2) pyrite alone, and (3) a combined EAOP and pyrite system. In EAOP alone, sulfanilamide was effectively oxidized (80%), while the electrochemical transformation of As(III)/Cr(VI) into As(V)/Cr(III) was limited. In just the pyrite system, As(III), Cr(VI), and sulfanilamide were adsorbed onto the surface of pyrite (60%, 20%, and 18%). Neither the EAOP nor the pyrite system alone could effectively treat the contaminants mixture. Nonetheless, the combined system completely removed As(III), Cr(VI), and sulfanilamide by the synergistic reaction. This could be attributed to the formation of green rust, a natural adsorbent mineral produced as a reaction of dissolved iron, generated via electrochemical pyrite oxidation, with the groundwater electrolyte (e.g., CO3 or SO4). This system harmonized the combined approach of EAOP and pyrite to effectively eliminate both organic and inorganic contaminants. ENVIRONMENTAL IMPLICATION: A paper proposed electrochemical oxidation (EO) with pyrite to remove both organic and inorganic contaminants from groundwater. The removal performance of the combined system was evaluated, and the synergistic mechanism was revealed. The combination of EO and pyrite with synergistic removal effectively removed the mixture of both contaminants. This could be attributed by the formation of green-rust by electrochemical activation for pyrite. Compared to the single system of EO and pyrite alone, the combined system with EO and pyrite improved removal performance. Results suggested that the combined system could be used for green groundwater remediation.

Recent advances in alginate-based composite gel spheres for removal of heavy metals

The discharge of heavy metal ions from industrial wastewater into natural water bodies is a consequence of global industrialisation. Due to their high toxicity and resistance to degradation, these heavy metal ions pose a substantial threat to human health as they accumulate and amplify. Alginate-based composite gels exhibit good adsorption and mechanical properties, excellent biodegradability, and non-toxicity, making them environmentally friendly heavy metal ion adsorbents for water with promising development prospects. This paper introduces the basic properties, cross-linking methods, synthetic approaches, modification methods, and manufacturing techniques of alginate-based composite gels. The adsorption properties and mechanical strength of these gels can be enhanced through surface modification, multi-component mixing, and embedding. The main production processes involved are sol-gel and cross-linking methods. Additionally, this paper reviews various applications of alginate composite gels for common heavy metals, rare earth elements, and radionuclides and elucidates the adsorption mechanism of alginate composite gels. This study aimed to provide a reference for synthesising new, efficient, and environmentally friendly alginate-based adsorbents and to contribute new ideas and directions for addressing the issue of heavy metal pollution.

Removal of cadmium and cobalt from water by Slovak bentonites: efficiency, isotherms, and kinetic study

Slovak bentonite was used as an effective natural adsorbent for the removal of Cd(II) and Co(II). Characterization of the samples was conducted using X-ray diffraction (XRD), high-resolution scanning electron microscopy with an X-ray energy dispersion spectrometer (SEM-EDS), and infrared spectroscopy (FT-IR). Adsorption experiments were carried out for pure water and artificial seawater, each containing cobalt and cadmium cations within the concentration range of 5-60 mg/L. The highest bentonite adsorption capacities of the tested bentonites were 23.5 (Cd) and 32.2 (Co) mg g-1. The kinetics data revealed that, in addition to chemisorption, intraparticle diffusion contributes to metal removal. The physical and structural properties of bentonites play an important role in adsorption. Bentonite P 135 from the Lieskovec deposit showed the highest efficiency for removing both ions, with removal percentages exceeding 90% and 77.5% for pure water and artificial seawater, respectively. The results indicate the suitability of using Slovak bentonites as an alternative sorbent for both metal extractions. The mechanism of metal ion adsorption on bentonite clay can be understood through surface complexation and ion exchange. The examined bentonite deposits show potential as promising natural sorbents for the removal of cobalt and cadmium cations from polluted waters.

Intramolecular generation of endogenous Cu(III) for selectively self-catalytic degradation of Cu(II)-EDTA from wastewater by UV/peroxymonosulfate

HO•/SO4•--based advanced oxidation processes for the decomplexation of heavy metal-organic complexes usually encounter poor efficiency in real scenarios. Herein, we reported an interesting self-catalyzed degradation of Cu(II)-EDTA with high selectivity in UV/peroxymonosulfate (PMS). Chemical probing experiments and competitive kinetic analysis quantitatively revealed the crucial role of in situ formed Cu(III). The Cu(III) species not only oxidized Cu(II)-EDTA rapidly at ∼3 × 107 M-1 s-1, but also exhibited 2-3 orders of magnitude higher steady-state concentration than HO•/SO4•-, leading to highly efficient and selective degradation of Cu(II)-EDTA even in complex matrices. The ternary Cu(II)-OOSO3- complexes derived from Cu(II)-EDTA decomposition could generate Cu(III) in situ via the Cu(II)-Cu(I)-Cu(III)-Cu(II) cycle involving intramolecular electron transfer. This method was also applicable to various Cu(II) complexes in real electroplating wastewater, demonstrating higher energy efficiency than commonly studied UV-based AOPs. This study provids a proof of concept for efficient decomplexation through activating complexed heavy metals into endogenous reactive species.

Polycarboxylate functionalized magnetic nanoparticles Fe3O4@SiO2@CS-COOH: Preparation, characterization, and immobilization of bovine serum albumin

Magnetic nanoparticles with increasing superparamagnetism and magnetic targeting have found widespread application in fields such as food and medicine. In this study, polycarboxylated magnetic nanoparticles (Fe3O4@SiO2@CS-COOH) were prepared by surface functionalizing iron tetraoxide (Fe3O4) nanoparticles with ethylenediaminetetraacetic acid (EDTA) as a modifier. The appropriate degree of functionalization modification was obtained by adjusting the EDTA concentration and the ratio of cross-linking agents. The prepared magnetic nanoparticles were analyzed with structural and property characterization. The results showed that the Fe3O4@SiO2@CS-COOH magnetic nanoparticles prepared with 4 % EDTA and cross-linking agents at a molar ratio of 3:4 were uniform in particle size, with an average size of roughly 7 nm, and possessed an abundant carboxylate content (310.8064 μmol/g) and a high magnetization intensity (35.05 emu/g). As a model protein, bovine serum albumin (BSA) was immobilized on the surface of magnetic particles. The largest amount of immobilized protein was 500.4376 mg BSA/g at pH 4.0 and no extra salt ions. According to molecular docking simulations, its immobilization was due to the interaction of amino and carboxyl groups at the Fe3O4@SiO2@CS-COOH/BSA interface. Fe3O4@SiO2@CS-COOH possesses a large number of carboxyl groups, strong protein immobilization, and magnetic responsiveness, which may have potential applications in biomedical and food fields.

Decomposition of metal-organic complexes and metal recovery in wastewater: A systematic review and meta-synthesis

Metals are rarely found as free ions in natural and anthropogenic environments, but they are often associated with organic matter and minerals. Under the context of circular economy, metals should be recycled, yet they are difficult to extract for their complex forms in real situations. Based on the protocols of review methodology and the analysis of VOS viewer, there are few reviews on the properties of metal-organic complexes, decomplexation methods, the effect of coexisting ions, the pH influence, and metal recovery methods for the increasingly complicated metal-organic complexes wastewater. Conventional treatment methods such as flocculation, adsorption, biological degradation, and ion exchange fail to decompose metal-organic complexes completely without causing secondary pollution in wastewater. To enhance comprehension of the behavior and morphology exhibited by metal-organic complexes within aqueous solutions, we presented the molecular structure and properties of metal-organic complexes, the decomplexation mechanisms that encompassed both radical and non-radical oxidizing species, including hydroxyl radical (OH), sulfate radical (SO˙4-), superoxide radical (O˙2-), hydrogen peroxide (H2O2), ozone (O3), and singlet oxygen (1O2). More importantly, we reviewed novel aspects that have not been covered by previous reviews considering the impact of operational parameters and coexisting ions. Finally, the potential avenues and challenges were proposed for future research.

A review of chloride ions removal from high chloride industrial wastewater: Sources, hazards, and mechanisms

To reduce metal pipe corrosion, improve product quality, and meet zero liquid discharge (ZLD) criteria, managing chloride ion concentrations in industrial wastewaters from metallurgical and chemical sectors has become increasingly important. This review provides detailed information on the sources, concentration levels, and deleterious effects of chloride ions in representative industrial wastewaters, and also summarizes and discusses various chloride ion removal techniques, including precipitation, ion exchange, physical separation, and advanced oxidation (AOPs). Among these, AOPs are particularly promising due to their ability to couple with other technologies and the diversity of their auxiliary technologies. The development of dechlorination electrode materials by electro-adsorption (CDI) can be inspired by the electrode materials used in chloride ion battery (CIB). This review also provides insights into exploring the effective combination of multiple chloride removal mechanisms, as well as the development of environmentally friendly composite materials. This review provides a theoretical basis and development direction for the effective treatment and secondary utilization of chlorine-containing industrial wastewater in the future.

Tuning active sites on biochars for remediation of mercury-contaminated soil: A comprehensive review

Mercury (Hg) contamination is acknowledged as a global issue and has generated concerns globally due to its toxicity and persistence. Tunable surface-active sites (SASs) are one of the key features of efficient BCs for Hg remediation, and detailed documentation of their interactions with metal ions in soil medium is essential to support the applications of functionalized BC for Hg remediation. Although a specific active site exhibits identical behavior during the adsorption process, a systematic documentation of their syntheses and interactions with various metal ions in soil medium is crucial to promote the applications of functionalized biochars in Hg remediation. Hence, we summarized the BC's impact on Hg mobility in soils and discussed the potential mechanisms and role of various SASs of BC for Hg remediation, including oxygen-, nitrogen-, sulfur-, and X (chlorine, bromine, iodine)- functional groups (FGs), surface area, pores and pH. The review also categorized synthesis routes to introduce oxygen, nitrogen, and sulfur to BC surfaces to enhance their Hg adsorptive properties. Last but not the least, the direct mechanisms (e.g., Hg- BC binding) and indirect mechanisms (i.e., BC has a significant impact on the cycling of sulfur and thus the Hg-soil binding) that can be used to explain the adverse effects of BC on plants and microorganisms, as well as other related consequences and risk reduction strategies were highlighted. The future perspective will focus on functional BC for multiple heavy metal remediation and other potential applications; hence, future work should focus on designing intelligent/artificial BC for multiple purposes.

Current technologies for heavy metal removal from food and environmental resources

Exposure to heavy metals in water and food poses a significant threat to human well-being, necessitating the efficient removal of these contaminants. The process of urban development exacerbates heavy metal pollution, thereby increasing risks to both human health and ecosystems. Heavy metals have the capacity to enter the food chain, undergo bioaccumulation and magnify, ultimately resulting in adverse effects on human health. Therefore, implementing effective pollution control measures and adopting sustainable practices are crucial for mitigating exposure and associated health risks. Various innovative approaches, including adsorption, ion exchange, and electrochemical technology, are currently being actively investigated to cope with the issue of heavy metal contamination. These innovative methods offer benefits such as efficient recycling, cost-effectiveness and environmental friendliness. In this review, we summarize recent advances for removing heavy metals from water, soil and food, providing valuable guidance for environmental engineers and researchers seeking to address contamination challenges.

A novel magnetic Fe3O4/cellulose nanofiber/polyethyleneimine/thiol-modified montmorillonite aerogel for efficient removal of heavy metal ions: Adsorption behavior and mechanism study

To efficiently remove heavy metals from wastewater, designing an adsorbent with high adsorption capacity and ease of recovery is necessary. This paper presents a novel magnetic hybridized aerogel, Fe3O4/cellulose nanofiber/polyethyleneimine/thiol-modified montmorillonite (Fe3O4/CNF/PEI/SHMMT), and explores its adsorption performance and mechanism for Pb2+, Cu2+, and Cd2+ in aqueous solutions. The hybrid aerogel has a slit-like porous structure and numerous exposed active sites, which facilitates the uptake of metal ions by adsorption. Pb2+, Cu2+, and Cd2+ adsorption by the hybridized aerogel followed the second-order kinetics and the Langmuir isotherm model, the maximum adsorption of Pb2+, Cu2+, and Cd2+ at 25 °C, pH = 6, 800 mg/L was 429.18, 381.68 and 299.40 mg/g, respectively. The adsorption process was primarily attributed to monolayer chemical adsorption, a spontaneous heat-absorption reaction. FTIR, XPS and DFT studies confirmed that the adsorption mechanisms of Fe3O4/CNF/PEI/SHMMT on Pb2+, Cu2+, and Cd2+ were mainly chelation, coordination, and ion exchange. The lowest adsorption energy of Pb2+ on the hybrid aerogel was calculated to be -2.37 Ha by DFT, which indicates that the sample has higher adsorption affinity and preferential selectivity for Pb2+. After 5 cycles, the adsorption efficiency of the aerogel was still >85 %. The incorporation of Fe3O4 improved the mechanical properties of the aerogel. The Fe3O4/CNF/PEI/SHMMT has fast magnetic responsiveness, and it is easy to be separated and recovered after adsorption, which is a promising potential for the treatment of heavy metal ions.

Heap leaching of ion adsorption rare earth ores and REEs recovery from leachate with lixiviant regeneration

In this work, semi-industrial scale heap leaching of 200 t ion adsorption rare earth ores (IRE-ore) and rare earth elements (REEs) recovery from lixivium was first conducted. Biosynthetic citrate/(Na)3Cit, a typical microbial metabolite, was chosen as the lixiviant to conduct heap leaching. Subsequently, an organic precipitation method was proposed, which used oxalic acid to effectively recover REEs and reduce the production cost by lixiviant regeneration. The results showed that the heap leaching efficiency of REEs reached 98 % with a lixiviant concentration of 50 mmol/L and a solid-liquid ratio of 1:2. The lixiviant can be regenerated during the precipitation process, with REE yields and impurity aluminum yields of 94.5 % and 7.4 %, respectively. The residual solution can then be cyclically used as a new lixiviant after simple adjustment. High-quality rare earth concentrates with a rare earth oxide (REO) content of 96 % can be finally obtained after roasting. This work provides an eco-friendly alternative for IRE-ore extraction to solve the environmental issues caused by traditional technology. The results proved feasibility and provided a foundation for in situ (bio)leaching processes in further industrial tests and production.

Anthropogenic influences on the sources and distribution of organic carbon, black carbon, and heavy metals in Daya Bay's surface sediments

The total organic carbon (TOC), total nitrogen (TN), black carbon (BC), δ13CTOC, δ15N, δ13CBC, grain size, and heavy metals of surface sediments collected from Daya Bay were determined to investigate the spatial distributions of these parameters and to evaluate the influences of human activities. Marine organic matter was found to constitute approximately 84.41 ± 7.70 % of these sediments on average. The western and northern regions of Daya Bay exhibited relatively fine grain sizes, weak hydrodynamic conditions, and high sedimentation rates, which favored the burial and preservation of organic matter. The high concentration of organic matter could be attributed to the influence of petroleum and aquaculture industries. Fossil fuels were the main source of BC. The enrichment factor (EF) and geo-accumulation index (Igeo) were used to evaluate the sources and pollution levels of heavy metals. The results revealed that the source and distribution of heavy metals were strongly influenced by human activities, resulting in moderate pollution levels across most regions of Daya Bay. A strong correlation was observed between the Igeo values of heavy metals and BC, TOC, TN, and mean particle grain size (Mz). This suggests that the ability of sediments in Daya Bay to enrich and adsorb heavy metals depends on the sediment grain size, the content and type of organic matter. Importantly, sediments in the inner bay of Daya Bay exhibited a greater capacity to impede the migration of heavy metals compared to those in the outer bay.

Antibacterial Effect of Melanoidins Derived From Xylose and Phenylalanine Against Bacillus cereus and Clostridium perfringens

Melanoidins produced from the combination of D-xylose and L-phenylalanine have been reported to exhibit strong antibacterial effects. This study investigated the influence of environmental factors, such as temperatures (10, 15, 20, 25, 30, 35, 40, and 45°C), pH (5.5, 6.0, 6.5, 7.0, 7.5, and 8.0), and water activity (aw: 0.99, 0.96, and 0.93), on the antibacterial effect of the melanoidins produced from the combination of D-xylose with L-phenylalanine against Bacillus cereus and Clostridium perfringens in culture media. Furthermore, freeze-dried powdered melanoidin was used to determine the minimum concentration for growth inhibition, to compare the antibacterial effect of the melanoidin with conventional food preservatives. The liquid melanoidins significantly inhibited the growth of B. cereus (up to 4 log CFU/mL at the maximum) and C. perfringens (up to 6.5 log CFU/mL at the maximum) regardless of the incubation temperatures. However, the remarkable difference between the presence and absence of the melanoidins was demonstrated in the range of 20-35°C as 4 log-cycle lower in B. cereus and 2 log-cycle lower in C. perfringens than those without the melanoidins. The antibacterial effect of the melanoidin on B. cereus was not influenced by pH from 5.5 to 7.0, which exhibited 2-3 log-cycle lower viable counts than those without the melanoidin. Only one log-cycle difference between with and without the melanoidin was shown in C. perfringens growth under the pH range of 5.5-7.0. Although there was no significant difference in the growth of B. cereus between three aw conditions, the melanoidin exhibited a significant antibacterial effect at aw 0.99 demonstrating 4 log-cycle lower viable numbers than those without the melanoidin. Minimum inhibitory concentration of the melanoidin powder for B. cereus and C. perfringens was 7 mg/mL and 15 mg/mL, respectively, regardless of the kind of foods. Furthermore, the melanoidin exhibited comparable antibacterial effect on B. cereus and C. perfringens to potassium sorbate and sodium benzoate under the same concentration as the minimum inhibitory concentration of the melanoidin, demonstrating 2 log-cycle reduction during 3 days of incubation period at 25°C. The results presented here suggest that the xylose- and phenylalanine-based melanoidin demonstrates the possibility to be an alternative food preservative.

Heavy Metals in Foods and Beverages: Global Situation, Health Risks and Reduction Methods

Heavy metals are chemical elements with a toxic effect on the human body. The expansion of industries has led to significant increasing levels of these constituents in the environment. Intensive agriculture can also lead to an increased concentration of heavy metals as a result of using different fertilizers and pesticides. Heavy metal accumulation in soil and plants represents a serious issue because of the potential risks to consumers. There are several methods available for the removal of these toxic components from different substrates (chemical precipitation, electrodialysis, coagulation and flocculation, photocatalytic removal, and adsorption-based processes), but most procedures are expensive and difficult to perform. Thus, more research is needed on the development of low-cost methods in foods. This work represents a review on the heavy metal presence in different food substrates (such as fruits and vegetables, milk and dairy products, meat and meat derivatives, oils, and alcoholic beverages) and provides an overview of the current situation worldwide, taking into account the fact that risks for human health are induced by the intensification of industry and the high degree of pollution. Considering that the toxicological quality of food affects its acceptability, this work provides valuable data regarding the actual situation on the proposed topic.

Highly Selective Electrocatalytic CuEDTA Reduction by MoS2 Nanosheets for Efficient Pollutant Removal and Simultaneous Electric Power Output

Electrocatalytic reduction of ethylenediamine tetraacetic acid copper (CuEDTA), a typical refractory heavy metal complexation pollutant, is an environmental benign method that operates at mild condition. Unfortunately, the selective reduction of CuEDTA is still a big challenge in cathodic process. In this work, we report a MoS2 nanosheet/graphite felt (GF) cathode, which achieves an average Faraday efficiency of 29.6% and specific removal rate (SRR) of 0.042 mol/cm2/h for CuEDTA at - 0.65 V vs SCE (saturated calomel electrode), both of which are much higher than those of the commonly reported electrooxidation technology-based removal systems. Moreover, a proof-of-concept CuEDTA/Zn battery with Zn anode and MoS2/GF cathode is demonstrated, which has bifunctions of simultaneous CuEDTA removal and energy output. This is one of the pioneer studies on the electrocatalytic reduction of heavy metal complex and CuEDTA/Zn battery, which brings new insights in developing efficient electrocatalytic reduction system for pollution control and energy output.

Heavy metal pollution in the aquatic environment: efficient and low-cost removal approaches to eliminate their toxicity: a review

Heavy metal contamination of water sources has emerged as a major global environmental concern, threatening both aquatic ecosystems and human health. Heavy metal pollution in the aquatic environment is on the rise due to industrialization, climate change, and urbanization. Sources of pollution include mining waste, landfill leachates, municipal and industrial wastewater, urban runoff, and natural phenomena such as volcanic eruptions, weathering, and rock abrasion. Heavy metal ions are toxic, potentially carcinogenic, and can bioaccumulate in biological systems. Heavy metals can cause harm to various organs, including the neurological system, liver, lungs, kidneys, stomach, skin, and reproductive systems, even at low exposure levels. Efforts to find efficient methods to remove heavy metals from wastewater have increased in recent years. Although some approaches can effectively remove heavy metal contaminants, their high preparation and usage costs may limit their practical applications. Many review articles have been published on the toxicity and treatment methods for removing heavy metals from wastewater. This review focuses on the main sources of heavy metal pollution, their biological and chemical transformation, toxicological impacts on the environment, and harmful effects on the ecosystem. It also examines recent advances in cost-effective and efficient techniques for removing heavy metals from wastewater, such as physicochemical adsorption using biochar and natural zeolite ion exchangers, as well as decomposition of heavy metal complexes through advanced oxidation processes (AOPs). Finally, the advantages, practical applications, and future potential of these techniques are discussed, along with any challenges and limitations that must be considered.

Synergistic removal of Cd(II)-organic complexes by combined permanent magnetic resins

Due to the enormous threat of pollution by heavy metal ions and organics, the effective removal of HMIs-organic complexes from various wastewater is of vital importance. In this study, synergistic removal of Cd(II) and para-aminobenzoic acid (PABA) by combined permanent magnetic anion-/cation-exchange resin (MAER/MCER) was examined in batch adsorption experiments. The Cd(II) adsorption isotherms fitted the Langmuir model at all tested conditions, suggesting a monolayer adsorption nature in both the sole and binary systems. Moreover, the Elovich kinetic model fitting demonstrated a heterogeneous diffusion of Cd(II) by the combined resins. At the organic acids (OAs) concentration of 10 mmol/L (molar ratio of OAs: Cd = 20:1), the adsorption capacities of Cd(II) by MCER decreased by 26.0, 25.2, 44.6, and 28.6%, respectively, under the coexistence of tannic acid, gallic acid, citric acid and tartaric acid, indicating the high affinity of MCER towards Cd(II). The MCER displayed high selectivity towards Cd(II) in the presence of 100 mmol/L of NaCl, with the adsorption capacity of Cd(II) decreasing by 21.4%. The "salting out" effect also promoted the uptake of PABA. Decomplexing-adsorption of Cd(II) by MCER and selective adsorption of PABA by MAER were proposed as the predominant mechanism for the synergistic removal of Cd(II) and PABA from the mixed Cd/PABA solution. The PABA bridging on MAER surface could promote the uptake of Cd(II). The combined MAER/MCER showed excellent reusability during five reuse cycles, indicative of the great potential in the removal of HMIs-organics from various wastewater.

Multivariate modeling and process optimization of Hg(II) remediation using solvothermal synthesized 2D MX/Fe3O4 by response surface methodology: characteristics and mechanism study

Two-dimensional MXene with layered structure has recently emerged as a nanomaterial with fascinating characteristics and applicability. Herein, we prepared the newly modified magnetic MXene (MX/Fe₃O₄) nanocomposite using solvothermal approach and investigated its adsorption behavior to study the removal efficiency of Hg(II) ions from aqueous solution. The effect of adsorption parameters such as adsorbent dose, time, concentration, and pH were optimized using response surface methodology (RSM). The experimental data fitted well with quadratic model to predict the optimum conditions for maximum Hg(II) ion removal efficiency which were found to be at adsorbent dose 0.871 g/L, time 103.6 min, concentration 40.17 mg/L, and 6.5 pH respectively. To determine the adequacy of the developed model, a statistical analysis of variance (ANOVA) was used, which demonstrated high agreement between the experimental data and the suggested model. According to isotherm result, the experimental data were following the best agreement with the Redlich-Peterson isotherm model. The results of the experiments revealed that the maximum Langmuir adsorption capacity of 699.3 mg/g was obtained at optimum conditions, which was closed to the experimental adsorption capacity of 703.57 mg/g. The adsorption phenomena was well represented by the pseudo-second-order model (R² = 0.9983). On the whole, it was clear that MX/Fe₃O₄ has lot of potential as a Hg(II) ion impurity removal agent in aqueous solutions.

Valorization of Fibrous Plant-Based Food Waste as Biosorbents for Remediation of Heavy Metals from Wastewater-A Review

Mobilization of heavy metals in the environment has been a matter of concern for several decades due to their toxicity for humans, environments, and other living organisms. In recent years, use of inexpensive and abundantly available biosorbents generated from fibrous plant-based food-waste materials to remove heavy metals has garnered considerable research attention. The aim of this review is to investigate the applicability of using fibrous plant-based food waste, which comprises different components such as pectin, hemicellulose, cellulose, and lignin, to remove heavy metals from wastewater. This contribution confirms that plant-fiber-based food waste has the potential to bind heavy metals from wastewater and aqueous solutions. The binding capacities of these biosorbents vary depending on the source, chemical structure, type of metal, modification technology applied, and process conditions used to improve functionalities. This review concludes with a discussion of arguments and prospects, as well as future research directions, to support valorization of fibrous plant-based food waste as an efficient and promising strategy for water purification.

Effective recovery of rare earth from (bio)leaching solution through precipitation of rare earth-citrate complex

Bioleaching is considered an alternative to traditional rare earth extraction technology. However, since rare earth elements exist as complexes in bioleaching lixivium, they cannot be directly precipitated by normal precipitants, which restricts their further development. This structurally stable complex is also a common challenge in various types of industrial wastewater treatment. In this work, a new method called a three-step precipitation process is first proposed to efficiently recover rare earth-citrate (RE-Cit) complexes from (bio)leaching lixivium. It consists of coordinate bond activation (carboxylation by pH adjustment), structure transformation (Ca²⁺ addition) and carbonate precipitation (soluble CO₃^2- addition). The optimization conditions are determined to adjust the lixivium pH to around 2.0, then add calcium carbonate until the n(Ca²⁺): n(Cit^3-) is more than 1.4:1 and lastly add sodium carbonate until n(CO₃^2-): n(RE³⁺) is more than 4:1. The results of precipitation experiments using imitated lixivium show that the rare earth yield is more than 96% and the impurity aluminum yield is less than 20%. Subsequently, pilot tests (1000 L) using real lixivium were successfully conducted. The precipitation mechanism is briefly discussed and proposed by thermogravimetric analysis, Fourier infrared spectroscopy, Raman spectroscopy and UV spectroscopy. This technology is promising in the industrial application of rare earth (bio)hydrometallurgy and wastewater treatment due to its advantages of high efficiency, low cost, environmental friendliness and simple operation.

Cu(II) removal from water by trimercapto-s-triazine trisodium salt modified alkaline lignin

To overcome the poor removal ability of alkaline lignin (AL) toward heavy metals, trimercapto-s-triazine trisodium salt (TMT) was selected as the modifying agent to introduce reaction groups. The Fourier transform infrared (FT-IR) spectra and the scanning electron microscopy (SEM) suggested that -SNa, C-N, and C = N groups were successfully introduced. Copper (II) was applied to evaluate the uptake performance of the adsorbent (AL-TMT). Adsorbent dosage and solution pH were taken into account to study their effects in the batch experiments. The pseudo-second-order dynamics and Langmuir models better described the experimental data. Nitrogen (N) and carbon (C) functional groups in thiotriazinone carried by AL-TMT were determined to be the primary uptake sites through X-ray photoelectron spectroscopy (XPS), FT-IR, and electrostatic potential (ESP). The selective experiments of AL-TMT toward Cd(II), Cu(II), Pb(II), Zn(II), Co(II), and Mg(II) were performed. It showed that AL-TMT possessed better adsorption selectivity toward Cu(II) than others. Furthermore, the density functional theory (DFT) calculations of thiotriazinone in AL-TMT also exhibited the lowest binding energy toward Cu than toward others. This work may provide a theoretical basis to facilitate the extraction of specific heavy metals from water or wastewater by using such modified alkaline lignin.

Promoted elimination of metronidazole in ferrous ions activated peroxydisulfate process by gallic acid complexation

We applied gallic acid (GA) as the complexing agent to stabilizing the regeneration of Fe²⁺ during the Fe²⁺/peroxydisulfate (PDS) Fenton-like reaction for promoting the removal of metronidazole (MTZ). This research evaluated the elimination of MTZ by optimizing the dose of GA and Fe²⁺ and pH condition. MTZ removal reached 83% at the GA: Fe²⁺ molar ratio of 1:1 (30 μM) and initial pH 5 and 6.2 after 120 min, and the kinetics showed two degradation phases (k_obs1 = 0.09636 for the rapid stage and k_obs2 = 0.01056 for the slow stage). The Fe²⁺ and GA complexes could expand the range of pH applicability and effectively stabilize the regeneration of Fe²⁺, which ultimately promoted the decontamination of MTZ. Sulfate radical (SO₄^.-), hydroxyl radicals, and singlet oxygen were proved to exist in this ternary system and contribute to MTZ removal, and SO₄^.- played the dominant role. Furthermore, the possible pathways and mechanisms for MTZ degradation were proposed, and the simulation result indicated that the toxicity of degradation intermediates of MTZ were declined. The GA assisted Fe²⁺/PDS system provided an improved promising advanced oxidation process for organic wastewater disposal.

Algae extract delamination of molybdenum disulfide and surface modification with glycidyl methacrylate and polyaniline for the elimination of metal ions from wastewater

A special type of two-dimensional (2D) material based conducting polymer was constructed by green synthesis and in-situ polymerization techniques. The 2D Molybdenum Disulfide (MoS₂) were first synthesized with the combination of, ammonium tetrathiomolybdate dissolved in 20 mL algae extract under stirring. After stirring for about 2 h, and then finally sulfurization was initiated using sulfur powder in 20 mL of sulfuric solution and stirred for 8 h. The resulting black precipitates of MoS₂ were collected by centrifugation at 5000 rpm. Moreover, the prepared MoS₂ was functionalized with glycidyl methacrylate (GMA) and form the MoS₂@PGMA. Further, the MoS₂@PGMA is combined with polyaniline (PANI) to form conducting polymer grafted thin film nanosheets named MoS₂@PGMA/PANI with a thickness in micrometer size through grafting method. The prepared materials were characterized by SEM, FTIR, XRD, XPS and EDX techniques. To check the performance of materials the adsorption study was performed. Moreover, the adsorption study toward Cu²⁺ and Cd²⁺ showed a tremendous results and the maximum adsorption was 307.7 mg/g and 214.7 mg/g respectively. In addition, the pseudo-first and second order models as well as the adsorption isotherm were investigated using the Langmuir and Freundlich model. The results were best fitted with the pseudo-second order and Langmuir models. The regeneration study was also conducted and MoS₂@PGMA/PANI nanosheets can be easily recycled and restored after five successful recycling. The established methodology for preparing the 2D materials and conducting polymer based MoS₂@PGMA/PANI nanosheets is expected to be applicable for other multiple applications.

Sustainable and reagent-free cathodic precipitation for high-efficiency removal of heavy metals from soil leachate

Heavy metal pollution of soils has become a serious environmental problem. Soil washing with degradable reagents is an effective remediation technique of heavy metal pollution, and the generated leachate must be appropriately treated before discharge. However, the existing methods usually have the problems of large consumption of regents, high cost, and secondary pollution. This study proposed a reagent-free electrochemical precipitation method to remove mixed heavy metal ions extracted from soils by citrate using inert electrodes (IrO₂-Ta₂O₅/Ti anode and graphite cathode). The results showed that the low potential of cathode led to the electrodeposition of Cd; the local alkaline environment provided by electro-mediated water reduction caused the hydrolytic precipitation of Zn and Pb; and the precipitation of Fe washed out from Fe-rich soil resulted in the coprecipitation of As on cathode surface. These combined cathodic precipitation processes decreased the concentrations of toxic heavy metals by over 99.4% after 12 h of electrolysis at 26 mA cm^-2. The electrodes exhibited high stability after multiple successive cycles of reuse. The concentrations of As, Zn, Pb and Cd in the leachate decreased to below the limits of industrial wastewater discharge in each cycle, and those in soils could be reduced by 53.8%, 58.8%, 25.5%, and 70.2% at the initial concentrations of 1549, 1016, 310 and 50 mg kg^-1, respectively. The heavy metal removal rate increased with increasing current density in the range of 0-52 mA cm^-2. This work provides an efficient and sustainable method for the remediation of site soils polluted by mixed heavy metals.

Electrocoagulation coupled with electrooxidation for the simultaneous treatment of multiple pollutants in contaminated sediments

In situ and simultaneous remediation of a variety of pollutants in sediments remains a challenge. In this study, we report that the combination of electrocoagulation (EC) and electrooxidation (EO) is efficient in the immobilization of phosphorus and heavy metals and in the oxidation of ammonium and toxic organic matter. The integrated mixed metal oxide (MMO)/Fe anode system allowed the facile removal of ammonium and phosphorus in the overlying water (99% of 10 mg/L NH₄⁺-N and 95% of 10 mg/L P disappeared in 15 and 30 min, respectively). Compared with the controls of the single Fe anode and single MMO anode systems, the dual MMO/Fe anode system significantly improved the removal of phenanthrene and promoted the transition of Pb and Cu from the mobile species to the immobile species. The concentrations of Pb and Cu in the toxicity characteristic leaching procedure extracts were reduced by 99% and 97% after an 8 hr operation. Further tests with four real polluted samples indicated that substantial proportions of acid-soluble fraction Pb and Cu were reduced (30%-31% for Pb and 16%-23% for Cu), and the amounts of total organic carbon and NH₄⁺-N decreased by 56%-71% and 32%-63%, respectively. It was proposed that the in situ electrogenerated Fe(II) at the Fe anode and the active oxygen/chlorine species at the MMO anode are conducive to outstanding performance in the co-treatment of multiple pollutants. The results suggest that the EC/EO method is a powerful technology for the in situ remediation of sediments contaminated with different pollutants.

Fenton Reaction–Unique but Still Mysterious

This study is devoted to the Fenton reaction, which, despite hundreds of reports in a number of scientific journals, provides opportunities for further investigation of its use as a method of advanced oxidation of organic macro- and micropollutants in its diverse variations and hybrid systems. It transpires that, for example, the choice of the concentrations and ratios of basic chemical substances, i.e., hydrogen peroxide and catalysts based on the Fe2+ ion or other transition metals in homogeneous and heterogeneous arrangements for reactions with various pollutants, is for now the result of the experimental determination of rather randomly selected quantities, requiring further optimizations. The research to date also shows the indispensability of the Fenton reaction related to environmental issues, as it represents the pillar of all advanced oxidation processes, regarding the idea of oxidative hydroxide radicals. This study tries to summarize not only the current knowledge of the Fenton process and identify its advantages, but also the problems that need to be solved. Based on these findings, we identified the necessary steps affecting its further development that need to be resolved and should be the focus of further research related to the Fenton process.

Anoxic iron electrocoagulation automatically modulates dissolved oxygen and pH for fast reductive decomplexation and precipitation of Cu(II)-EDTA: The critical role of dissolved Fe(II)

Fe-based replacement and precipitation are promising methods for removal of copper ethylenediaminetetraacetic acid (Cu(II)-EDTA) but are limited by the necessity of controlling pH and dissolved oxygen. The details of the decomplexation mechanism also remain unclear. The present work investigated an anoxic iron electrocoagulation process capable of automatically modulating anoxic conditions and solution pH during exposure to air and thus promoting the rapid and thorough decomplexation of Cu(II)-EDTA. Dissolved Fe (II), rather than Fe(II)-bearing minerals, was found to be primarily responsible for the reduction of Cu(II)-EDTA to Cu(I)-EDTA and for the subsequent replacement reaction to generate free Cu(I) ions within the initial pH range of 2-7. The Cu(I) was primarily precipitated as Cu₂O on the surface of green rust and magnetite as the pH was increased. The aeration of these Fe-containing precipitates released free Cu(I) ions instead of chelated Cu into solution, allowing for recycling of the Cu. This release of Cu(I) was likely induced by the pH decrease during aeration. This study provides important insights regarding the reductive decomplexation of chelated Cu(II) and the recovery of Cu via anoxic iron electrocoagulation, which is a promising green approach to recycling Cu from wastewater.

Recent progress on electrospun nanofibrous polymer membranes for water and air purification: A review

Developing new polymer membranes with excellent thermal, mechanical, and chemical stability has shown great potential for various environmental remediation applications such as wastewater treatment and air filtration. Polymer membranes have been widely investigated over the past years and utilized to overcome severe ecological issues. Membrane-based technologies play a critical role in water purification and air filtration with the ability to act efficiently and sustainably. Electrospun nanofiber membranes have displayed excellent performance in removing various contaminants from water, such as bacteria, dyes, heavy metals, and oil. These nanofibrous membranes have shown good potential to filter the air from tiny particles, volatile organic compounds, and toxic gases. The performance of polymer membranes can be enhanced by fine-tuning polymer structure, varying surface properties, and strengthening overall membrane porosity. In this review, we discuss the involvement of electrospun nanofibrous membranes in different environmental remediation applications. It further reviews the recent progress of polymer membrane development by utilizing nanoparticles and naturally occurring polymers.

Bioelectrochemical systems-based metal removal and recovery from wastewater and polluted soil: Key factors, development, and perspective

Bioelectrochemical systems (BES) are considered efficient and sustainable technologies for bioenergy generation and simultaneously removal/recovery metal (loid)s from soil and wastewater. However, several current challenges of BES-based metal removal and recovery, especially concentrating target metals from complex contaminated wastewater or soil and their economic feasibility of engineering applications. This review summarized the applications of BES-based metal removal and recovery systems from wastewater and contaminated soil and evaluated their performances on electricity generation and metal removal/recovery efficiency. In addition, an in depth review of several key parameters (BES configurations, electrodes, catalysts, metal concentration, pH value, substrate categories, etc.) of BES-based metal removal and recovery was carried out to facilitate a deep understanding of their development and to suggest strategies for scaling up their specific application fields. Finally, the future intervention on multifunctional BES to improve their performances of mental removal and recovery were revealed.

A critical and recent developments on adsorption technique for removal of heavy metals from wastewater-A review

This review provides a quantitative description of the nano-adsorbent processing and its viability against wastewater detoxification by extracting heavy metal ions. The impact of nano-adsorbent functionalities on specific essential attributes such as the surface area, segregation, and adsorption capacity were comprehensively evaluated. A detailed analysis has been presented on the characteristics of nanomaterials through their limited resistance to adsorb some heavy metal ions. Experimental variables such as the adsorbent dosage, pH, substrate concentration, response duration, temperature, and electrostatic force that influence the uptake of metal ions have been studied. Besides, separate models for the adsorption kinetics and isothermal adsorption have been investigated to understand the mechanism behind adsorption. Here, we reviewed the different adsorbent materials with nano-based techniques for the removal of heavy metals from wastewater and especially highlighted the nano adsorption technique. The influencing factors such as pH, temperature, dosage time, sorbent dosage, adsorption capacities, ion concentration, and mechanisms related to the removal of heavy metals by nano composites are highlighted. Lastly, the application potentials and challenges of nano adsorption for environmental remediation are discussed. This critical review would benefit engineers, chemists, and environmental scientists involved in the utilization of nanomaterials for wastewater treatment.

Efficient removal of mercury and chromium from wastewater via biochar fabricated with steel slag: Performance and mechanisms

Biochar derived from biomass is regarded as a promising adsorbent for wastewater treatment, but the high cost of modification is still a challenge for its large-scale practical applications. In this study, we employed steel slag as a low-cost fabricant and synthesized hydrothermally carbonized steel slag (HCSS), as a stable environmentally functional material for heavy metal removal. Typically, positively and negatively charged heavy metal contaminants of Hg²⁺ and Cr₂O₇²⁻ were employed to testify the performance of HCSS as an adsorbent, and good capacities [(283.24 mg/g for Hg (II) and 323.16 mg/g for Cr (VI)] were found. The feasibility of HCSS on real wastewater purification was also evaluated, as the removal efficiency was 94.11% and 88.65% for Hg (II) and Cr (VI), respectively. Mechanism studies revealed that the modification of steel slag on bio-adsorbents offered copious active sites for pollutants. As expected, oxygen-containing functional groups in HCSS acted as the main contributor to adsorption capacity. Moreover, some reactive iron species (i.e., Fe²⁺) played an essential role in chemical reduction of Cr (VI). The adsorptive reactions were pH-dependent, owing to other more mechanisms, such as coprecipitation, ion-exchange, and electrostatic attraction. This promising recycling approach of biomass waste and the design of agro-industrial byproducts can be highly suggestive of the issues of resource recovery in the application of solid waste-derived environmentally functional materials for heavy metal remediation.

Humic acid-coated hydrated ferric oxides-polymer nanocomposites for heavy metal removal in water

Water pollution by toxic heavy metals poses a threat to the environment and human bodies. Herein, a novel hydrated ferric oxide nanoparticle (HFO) based hybrid adsorbent was fabricated for the removal of toxic Cu(II), Cd(II) and Pb(II) from water. HFOs were immobilized into a porous resin D-201, and then this nanocomposite HFO-D201 was coated with humic acid (HA) to enhance the binding sites of target metals. Both HFOs and HA contribute to the sequestration of heavy metals. The as-synthesized hybrid adsorbent HA-HFO-D201 exhibited excellent performance on the removal of Cu(II), Cd(II), and Pb(II) in a pH range of 3-9, while no Fe leaching was observed. The presence of natural organic matter (20 mg C/L) has limited influences on the adsorption, and more than 85% of the target metals can be removed after treatment. HA-HFO-D201 showed preferable adsorption toward Cu(II) and Pb(II) (1 mg/L) from the background Ca²⁺ solution at much higher concentrations (100 mg/L), while the retention of Cd(II) (1 mg/L) decreased to some extent. Fixed-bed column experiments exhibited that the treatment capacities of HA-HFO-D201 are 90 bed volumes (BV) for Cd(II), 410 BV for Pb(II) and > 800 BV for Cu(II) of simulated contaminated water to meet the WHO drinking water standard. Meanwhile, depleted HA-HFO-D201 can be readily regenerated by a chelating agent Na₂EDTA for repeated use. The hybrid adsorbent HA-HFO-D201 has excellent potential to remove heavy metals in water treatment systems.

An Electrochemical Strategy for Simultaneous Heavy Metal Complexes Wastewater Treatment and Resource Recovery

Heavy metals chelated with coexisting organic ligands in wastewater impose severe risks to public health and the ambient ecosystem but are also valuable metal resources. For sustainable development goals, the treatment of heavy metal complexes wastewater requires simultaneous metal-organic bond destruction and metal resource recovery. In this study, we demonstrated that a neutral pH electro-Fenton (EF) system, which was composed of an iron anode, carbon cloth cathode, and sodium tetrapolyphosphate electrolyte (Na₆TPP), could induce a successive single-electron activation pathway of molecular oxygen due to the formation of Fe(II)-TPP complexes. The boosted •OH generation in the Na₆TPP-EF process could decomplex 99.9% of copper ethylene diamine tetraacetate within 8 h; meanwhile, the released Cu ions were in situ deposited on the carbon cloth cathode in the form of Cu nanoparticles with a high energy efficiency of 2.45 g kWh^-1. Impressively, the recovered Cu nanoparticles were of purity over 95.0%. More importantly, this neutral EF strategy could realize the simultaneous removal of Cu, Ni, and Cr complexes from real electroplating effluents. This study provides a promising neutral EF system for simultaneous heavy metal complexes wastewater treatment and resource recovery and sheds light on the importance of molecular oxygen activation in the field of pollutant control.

Magnetic sporopollenin supported polyaniline developed for removal of lead ions from wastewater: Kinetic, isotherm and thermodynamic studies

This study evaluated the synthesis of novel binary functionaladsorbent based on sporopollenin, magnetic nanoparticles, and polyaniline to produce MSP-PANI. The MSP-PANI was applied to enhance uptake of lead ions (Pb²⁺) from wastewater samples. The functionalities, surface morphology, magnetic properties, and elemental composition of the newly synthesized nanocomposite were investigated using Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), vibration sample magnetometer (VSM), and energy-dispersive X-ray spectroscopy (EDX), respectively. The experimental condition for the adsorption process was MSP/PANI ratio 1:1, pH ∼6, adsorbent dosage 40 mg, and contact time 90 min at room temperature. Under the proposed condition, lead ions removal were obtained as 83%, 88% and 95% for MSPE, PANI, and MSP/PANI, respectively. Based on the experimental and predicted data, the adsorption was corresponded to the psudo-second-order (R² = 0.999) kinetics model, and the adsorption equilibrium corresponded to the Langmuir model (R² = 0.996). Langmuir isotherm showed the maximum adsorption capacity of MSP-PANI for lead ions was 163 mg/g and followed the monolayer pattern. Hence, thermodynamic model under Van't Hoff equation suggested that the adsorption mechanism was physio-sorption with endothermic nature. Therefore, this research can help the researchers to use magnetic nanoparticles for lead removal in highly polluted areas.

Integrated approaches to mitigate threats from emerging potentially toxic elements: A way forward for sustainable environmental management

Potentially toxic elements (PTEs) such as toxic metal (loid)s and other emerging hazardous contaminants, exist in the environment and poses a serious threat. A large amount of wastewater containing PTEs such as cadmium, chromium, copper, nickel, arsenic, lead, zinc, etc. Release from industries during production process. Besides these, chemical-based fertilizers used in soils during crop production have become one of the crucial sources of PTEs. Various techniques are being employed for the mitigation of PTEs like chemical precipitation, ion exchange, coagulation, activated carbon, adsorption, membrane filtration, and bioremediation. Among these mitigation strategies, biological processes such as bioremediation, phytoremediation etc. Are extensively used, as they are economic have high-efficiency rate and are eco-friendly. This review intends to provide information on PTEs contamination through various sources; along with the toxicity of metal (loid)s with respect to their patterns of transmission and risks in the changing environment. Various remediation methods for the management of these pollutants along with their techno-economic perspective are also summarized in this review.

Amorphous iron oxides anchored on BiOCl nanoplates as robust catalysts for high-performance photo-Fenton oxidation

Semiconductor supported iron oxides are highly promising catalysts to remove organic pollutants in photo-Fenton. Development of robust composite catalysts with both high activity and stability is essential. In this work, amorphous iron oxide layers are uniformly and tightly anchored on two-dimensional (2D) BiOCl nanoplates through post precipitation-deposition and subsequent low-temperature thermal treatment at 150-350 °C. A low iron loading amount (1-2 wt.%) is sufficient to make the resulted composite (BiOCl-Fe) catalysts superior in photo-Fenton oxidation of phenol (10 mg/L) with high mineralization efficiency (up to about 80% in 60 min). The low-temperature thermal treatment can significantly enhance the stability of catalysts with much less iron leached and high photo-Fenton performance maintained. The intimate contact between the amorphous iron oxide layers and the 2D BiOCl nanoplates could guarantee the fluent electron transfer and efficient activation of H₂O₂ at interfaces. Compared with the pristine BiOCl, the BiOCl-Fe catalysts possess faster separation of the charge carriers. The predominant active species turns from O₂^•- in photocatalysis to HO^• in the photo-Fenton catalysis. This research could provide enhanced understanding on the synthesis of robust catalysts and the structure optimization of BiOCl supported iron oxides for photo-Fenton.

Decomplexation of Cu(II)-EDTA by synergistic activation of persulfate with alkali and CuO: Kinetics and activation mechanism

Heavy metals usually coexist with a variety of chelating agents to form heavy metal complexes in industrial wastewater. The decomplexation of heavy metal complexes is the crucial step before the removal of heavy metals via alkaline precipitation process. An efficient synergistic activation of persulfate (PS) with alkali and CuO was used for the simultaneous decomplexation of Cu-ethylenediamine tetraacetic acid (Cu(II)-EDTA) (3.14 mM) and the Cu(II) precipitation. The experimental results demonstrated that nearly complete removal of Cu(II) could be achieved by synergistic activation of PS with alkali and CuO at pH 11 after 2 h of decomplexation reaction. However, sole PS could not effectively decomplex Cu(II)-EDTA (13.5%), while the alkaline activation of PS could accomplish 57.0% removal of Cu(II). Radical scavenger tests indicated that reactive oxygen species (ROS) including SO₄^•-, •OH and O₂^•- were responsible for the decomplexation of Cu(II)-EDTA in the synergistic activation of PS with alkali and CuO. As a heterogeneous activator, CuO possessed excellent reusability and long-lasting catalytic activity and the rate constant value (k) of Cu(II) removal showed an increase (from 0.0326 min^-1 in the first cycle to 0.0491 min^-1 in the 24^th cycle) with 24 cycles experiments. Furthermore, the biotoxicity evaluation of treated solution revealed that the biotoxicity of Cu(II)-EDTA contaminated wastewater could be effectively mitigated by the synergistic activation of PS with alkali and CuO because of the efficient precipitation of Cu(II) and oxidative degradation of EDTA organic ligands, which was favorable for the subsequent biochemical treatment.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.