Microbiology, chemistry and biofilm development in a pilot drinking water distribution system with copper and plastic pipes

Study on adsorption and desorption characteristics of lead pollution by biofilm in drinking water pipeline from multi-factor perspective

This study investigates lead adsorption and desorption behaviors in biofilms on drinking water pipeline materials (PVC, 304 stainless steel, copper) under varying flow rate, pH, and residual chlorine. Biofilms on stainless steel exhibited the highest adsorption capacity (450.81 μmol/m2), whereas PVC biofilms had the greatest desorption potential (25.30 μmol/m2). Optimal lead adsorption occurred at neutral pH (7.5), low flow velocity (0.10 m/s), and moderate chlorine concentration (0.3 mg/L). Optimal lead adsorption occurred at neutral pH (7.5), low flow velocity (0.10 m/s), and moderate chlorine concentration (0.3 mg/L). In contrast, higher flow velocities, acidic conditions, and elevated chlorine levels promoted desorption or inhibited interactions. PVC biofilms exhibited the highest biomass (1.58 × 106 CFU/cm2) and extracellular polymeric substances (EPS) (348 mg/m2), correlating with increased lead adsorption. Functional analysis revealed a higher abundance of ion-transport-related (functions associated with the movement of ions such as heavy metals across microbial cell membranes) functions in PVC biofilms, contributing to enhanced stability. The study offers valuable insights for optimizing pipe material selection and operational strategies to reduce lead contamination in water systems.

Chlorination enhances the phthalates release and increases the cytotoxicity and bacterial functions related to human disease of drinking water in plastic pipes

The interaction between water and pipe surfaces can deteriorate drinking water quality, thus threatening public health. However, uncertainties remain in the release mechanism of phthalates acid esters (PAEs) from plastic pipes and their effects on drinking water quality. Our study indicated that PAEs released from polyvinyl chloride (PVC) pipes was higher than polyethylene (PE) pipes. Chlorine disinfection increased the released PAEs concentration in effluents of PE-Cl2 and PVCCl2 pipes to 6.60∼7.87 μg/L and 7.45∼8.88 μg/L, respectively. PAEs release varied the CHO and tannins numbers in dissolved organic matter (DOM), increasing the cytotoxicity of water. Although chorine disinfection reduced the abundance of pathogenic bacteria, it upregulated the relative abundance of bacterial metabolic pathways related to human disease, such as drug resistance: antimicrobial and cancer: overview. In addition, various biofilm bacterial community compositions affected the interactions between bacteria and pipe surfaces, and the roughness of pipe surfaces increased after biofilm formation. The hydrophilicity of pipe surfaces also increased due to biofilm formation and chlorine disinfection. After five months of running, higher hydrophilicity of PVC pipe surface was observed than that of PE pipes, especially after chlorine disinfection, consequently enhancing PAEs release. In conclusion, chlorine disinfection accelerated PAEs release from plastic pipes by increasing the hydrophilicity of pipe surfaces, resulting in higher cytotoxicity and microbial risk of drinking water, especially in PVCCl2 pipes. This study revealed the influence of chlorine disinfection on PAEs release and its potential risk to public health, which provided insightful visions for the future drinking water security monitoring.

What happens in your water system? Impact of materials, temperature, stagnation and chlorination on water quality and biofilm formation

Building water distribution system materials are diverse and their impact on water quality depends on nutrients, stagnation, and temperature. The main objective was to investigate the interplay between material type, temperature and stagnation on water quality and biofilm formation potential. CDC biofilm reactors were used to compare concentrations of metals, total (DOC) and biodegradable (BDOC) dissolved organic carbon, and total and viable cells densities in water and biofilms in contact with coupons of 6 materials: polypropylene (PP), polyvinyl chloride (PVC), ethylene propylene diene monomer (EPDM), cross-linked polyethylene (PEX), stainless steel (SS) and copper (Cu). All materials were colonized by bacteria, with denser biofilm observed on EPDM > PP > PVC > PEX > Cu - SS. Copper and EPDM reactors showed different dynamics of accumulation and release of Cu and Pb, with bulk Pb concentrations exceeding 5 μg/L. Increasing temperatures from 25 °C to 40, 55 and 60 °C resulted in an increase by at least a factor 2 of DOC and BDOC, a temporary decrease in cell viability (%) and contrasting trends for suspended total bacteria (up to 1.4-log). Biofilm densities remained lower for all reactors after two months of constant heating at 40 °C, even further for copper reactors heated to 55 °C (2.5-log) and 60 °C (2.7-log). A 4-week stagnation at room temperature promoted total bacteria recovery in water and biofilm for all materials except copper. Extending stagnation to 6 months (COVID-19 shutdown) further increased total bacteria and the viable fraction in water, except in copper reactors.

Impact of stormwater on biofilm density and microbial community composition in water distribution networks

Harvesting of stormwater and injecting it into aquifers for storage and recovery during high water demand periods is a promising technology for augmenting conventional water reserves. However, little has been known on how stormwater impacts the biofouling of water distribution infrastructure. This study evaluated the effect on harvested and limestone aquifer treated stormwater on biofilm formation in a pilot distribution pipe network compared to an identical drinking water pipe rig. Coupons made of cement, copper and polyvinyl chloride (PVC) pipe materials were installed to each pipe rig and exposed to stormwater or drinking water. The total cell counts determined by flow cytometry on the pilot rig coupons were in the order of 105 to 107 cells/cm2 for both source waters and showed some variation over the duration of the study. The culturable cell counts were somewhat higher for stormwater exposed coupons than for coupons in mains water rig. The total number of thermotolerant coliforms was notably higher on coupons exposed to stormwater than on those exposed to mains water. Considerable differences were observed in the bacterial and eukaryotic communities on coupons made of various materials and exposed to mains water and stormwater using pyrosequencing. Moreover, seasonal variations were observed in community composition and diversity. A number of bacterial and eukaryotic families and genera harbouring potential human pathogens were detected in both mains water and stormwater systems, with larger numbers of genera observed in the latter indicating a potentially increased risk of exposure to pathogens with stormwater. The stormwater system also harboured sulfur reducers, and a greater diversity of iron oxidisers. A number of bacterial genera that contribute to nitrogen cycling were observed in both mains water and stormwater systems. A number of bacteria grazing eukaryotes were detected, indicating that the biofilm communities are quite dynamic and the abundance of bacteria is able to support higher level eukaryotes.

Influence of biofilm and calcium carbonate scaling on lead transport in plastic potable water pipes: A laboratory and molecular dynamics study

This study investigated lead (Pb) transport through new, biofilm-laden, and calcium carbonate-scaled crosslinked polyethylene (PEX-A) and high-density polyethylene (HDPE) potable water pipes. The research focused on Pb accumulation through short-term exposure incidents (6 h) and Pb release for a longer duration (5 d). A mechanistic investigation of the surface morphology variations of plastic pipes following biofilm and scale formation has been conducted. The nanoscale surface asperities in new PEX-A pipes and microscale roughness features in new HDPE pipes supported the differences in biofilm abundance, scale formation, and metal uptake results between these two pipes. Biomass analysis and dissolved organic matter (DOM) quantification using three-dimensional excitation emission spectroscopy revealed a greater release of biofilm biomass during the Pb accumulation and release experiments from biofilm-laden HDPE pipes. Both biofilm-laden plastic pipes accumulated a significantly greater level of Pb compared to the new and scaled pipes. However, scaled pipes showed the highest Pb release, while biofilm-laden pipes released the least. Additionally, investigation of Pb2+ exchange from the pipe surface in the presence of Ca2+ in the solution indicated that divalent cations in water can trigger further Pb release from the pipe surface. Furthermore, the molecular dynamics simulation provided valuable insights into the interaction between different pipe surfaces with Pb with respect to affinity and binding energy.

Biofilm formation dynamics in long-distance water conveyance pipelines: Impacts of nutrient levels and metal stress

Biofilm formation in long-distance water conveyance pipelines poses significant risks to water quality, particularly under varying nutrient levels and heavy metal stress. However, the impacts of pipeline material on biofilm formation dynamics under different raw water conditions remain elusive. This study investigated the effects of nutrient availability and Fe-Mn stress on biofilm development, structural stability, bacterial community composition, and the occurrence of viable but non-culturable (VBNC) bacteria. Using reactors with different nutrient conditions, we observed that increased nutrient levels promote biofilm growth but lead to greater instability, heightening the risk of secondary contamination. Notably, nutrient escalation beyond a critical threshold had a diminishing impact on biofilm community composition. Additionally, Fe-Mn stress, while initially enhancing microbial adhesion and metabolic activity, ultimately inhibited biofilm formation over time and increases the prevalence of VBNC bacteria, particularly on stainless steel (SS) surfaces. Our findings also highlighted the importance of material selection for pipelines, with polyvinyl chloride (PVC) showing reduced biofilm formation compared to SS, making it a more suitable option for transporting raw water in environments with high metal content. Dispersal limitation determined the bacterial community assembly during the biofilm formation, accounting for 64.53-90.67 % of the variability in different scenarios. These insights offer valuable guidance for managing biofilm-related issues in water distribution systems, emphasizing the need for careful control of nutrient levels and material choice to ensure water safety over long distances.

Unveiling the microbial diversity of biofilms on titanium surfaces in full-scale water-cooling plants using metagenomics approach

Microbial colonization on the titanium condenser material (TCM) used in the cooling system leads to biofouling and corrosion and influences the water supply. The primary investigation of the titanium condenser was infrequently studied on characterizing biofilm-forming bacterial communities. Different treatment methods like electropotential charge, ultrasonication, and copper coating of titanium condenser material may influence the microbial population over the surface of the titanium condensers. The present study aimed to catalog the primary colonizers and the effect of different treatment methods on the microbial community. CFU (1.7 × 109 CFU/mL) and ATP count (< 5000 × 10-7 relative luminescence units) showed a minimal microbial population in copper-coated surface biofilm as compared with the other treatments. Live and dead cell result also showed consistency with colony count. The biofilm sample on the copper-coated surface showed an increased dead cell count and decreased live cells. In the metagenomic approach, the microbiome coverage was 10.06 Mb in samples derived from copper-coated TCM than in other treated samples (electropotential charge-17.94 Mb; ultrasonication-20.01 Mb), including control (10.18 Mb). Firmicutes preponderate the communities in the biofilm samples, and Proteobacteria stand next in the population in all the treated condenser materials. At the genus level, Lactobacillaceae and Azospirillaceae dominated the biofilm community. The metagenome data suggested that the attached community is different from those biofilm samples based on the environment that influences the bacterial community. The outcome of the present study depicts that copper coating was effective against biofouling and corrosion resistance of titanium condenser material for designing long-term durability.

Unexpected weakened formation of disinfection byproducts and enhanced production of halates by cupric oxide during chlorination of peptide-bound aspartic acid

Under the condition that the residual chlorine is guaranteed, the biofilm still thrives in drinking water distribution systems through secreting a large number of extracellular polymeric substances (EPS), in which protein components are the primary precursor of disinfection byproducts (DBPs), mostly in the form of combined amino acids. The aim of this study is to investigate the action of CuO on the formation of halates (XO3-, ClO3- and BrO3-) and DBPs (trihalomethanes, THMs; haloacetonitriles, HANs) with aspartic acid tetrapeptide (TAsp) as protein surrogate. The presence of CuO promoted the self-decay rather than TAsp-induced decay of oxidants, resulting in an increase in XO3- yield and a decrease in DBPs yield. It was CuO-induced weaker production of cyanoacetic acid and 3-oxopropanoic acid that induced the decreased yields of HANs and THMs, respectively. The FTIR and Raman spectra indicate a weak complexation between CuO and TAsp. Given this, the CuO-HOX/OX- complexes were inferred to be reactive to HOX/OX- but less reactive to TAsp. The study helps to better understand the formation of XO3- and DBPs during the chlorination of EPS, and propose precise control strategies when biofilm boosts in water pipes.

Effect of household pipe materials on formation and chlorine resistance of the early-stage biofilm: various interspecific interactions exhibited by the same microbial biofilm in different pipe materials

Microbial community biofilm exists in the household drinking water system and would pose threat to water quality. This paper explored biofilm formation and chlorination resistance of ten dual-species biofilms in three typical household pipes (stainless steel (SS), polypropylene random (PPR), and copper), and investigated the role of interspecific interaction. Biofilm biomass was lowest in copper pipes and highest in PPR pipes. A synergistic or neutralistic relationship between bacteria was evident in most biofilms formed in SS pipes, whereas four groups displayed a competitive relationship in biofilms formed in copper pipe. Chlorine resistance of biofilms was better in SS pipes and worse in copper pipes. It may be helped by interspecific relationships, but was more dependent on bacteria and resistance mechanisms such as more stable extracellular polymeric substance. The corrosion sites may also protect bacteria from chlorination. The findings provide useful insights for microbial control strategies in household drinking water systems.

Occurrence of coliforms and biofilm-forming bacteria in raw, treated, and distributed water from two waterwork systems in Osun State, Southwestern Nigeria

This study assessed the bacteriological quality of raw, treated, and distributed water from Ede-Erinle and Opa reservoirs in Osun State, Nigeria. This was to determine the potability of water from these waterwork stations. Eighteen sampling points were established across the two reservoir networks for this study. Samples were collected bi-monthly for two annual cycles. Serial dilution and pour plate methods were employed for the enumeration of bacterial load. Total heterotrophic bacteria count (THBC) and total coliform bacteria count (TCBC) were enumerated on nutrient and MacConkey agar at 37 °C, respectively. Bacterial isolates were characterized using biochemical identification methods with reference to Bergey's Manual of Determinative Bacteriology. Bacterial isolates and biofilm formation were further identified molecularly through the PCR method using specific universal primers. Mean values of THBC and TCBC in distributed water from Ede-Erinle (9.61 × 104 ± 1.50 × 104 CFU/mL; 69.56 ± 26.81 CFU/mL) and Opa waterworks (9.58 × 104 ± 2.55 × 104 CFU/mL; 142.94 ± 44.41 CFU/mL) exceeded permissible limits for drinking water. Paenibacillus lautus, Bacillus pseudomycoides, Pseudomonas aeruginosa, and Pseudomonas stutzeri showed biofilm-forming capacity. The study concluded that the presence of coliforms and biofilm-forming bacteria in distributed water implies that the water is unfit for consumption without further treatment.

Growth dynamic of biofilm-associated Naegleria fowleri in freshwater on various materials

In industrial water systems, the occurrence of biofilm-associated pathogenic free-living amoebae (FLA) such as Naegleria fowleri is a potential hygienic problem, and factors associated with its occurrence remain poorly understood. This study aimed to evaluate the impact of four cooling circuit materials on the growth of N. fowleri in a freshwater biofilm formed at 42°C and under a hydrodynamic shear rate of 17 s-1 (laminar flow): polyvinyl chloride, stainless steel, brass, and titanium. Colonization of the freshwater biofilms by N. fowleri was found to be effective on polyvinyl chloride, stainless steel, and titanium. For these three materials, the ratio of (bacterial prey)/(amoeba) was found to control the growth of N. fowleri. All materials taken together, a maximum specific growth rate of 0.18 ± 0.07 h-1 was associated with a generation time of ~4 h. In contrast, no significant colonization of N. fowleri was found on brass. Therefore, the contribution of copper is strongly suspected.

Characterizing the development of biofilm in polyethylene pipes in the non-chlorinated Danish drinking-water distribution system

In newly commissioned drinking-water polyethylene (PE) pipes, biofilm develops on the inner pipe surface. The microbial community composition from colonization to the establishment of mature biofilms is less known, including the effect on the distributed water quality. Biofilm development was followed through 1.5 years in PE-pipe side streams at two locations of a full-scale, non-chlorinated drinking-water distribution system (leaving a waterworks versus 5-6 km from a waterworks) along with inlet and outlet water quality. Mature biofilms were established after ∼8-9 months, dominated by Proteobacteria, Actinobacteria and Saccharibacteria (61-93% relative abundance), with a higher diversity (OTUs/Shannon Index/16S rRNA gene amplicon sequencing) in pipes in the far end of the distribution system. Comamonadaceae, and specifically Aquabacterium (>30% of reads), dominated young (∼1.5-month-old) biofilms. Young biofilms were linked to increased microbiological counts in drinking water (HPC/ATP/qPCR), while the establishment of mature biofilms led to a drop in HPC and benefited the water quality, highlighting the importance of optimizing commissioning procedures for rapidly achieving mature and stable biofilms.

Copper ion affects oxidant decay and combined aspartic acid transformation during chlorination in water pipes: Differentiated action on the yield of trihalomethanes and haloacetonitriles

The chlorination of extracellular polymeric substances (EPS) secreted by biofilm often induces the formation of high-toxic disinfection byproducts (DBPs) in drinking water distribution systems. The protein components in EPS are the main precursors of DBPs, which mostly exist in the form of combined amino acids. The paper aimed to study the action of a pipe corrosion product (Cu2+) on the formation of DBPs (trihalomethanes, THMs; haloacetonitriles, HANs) with aspartic acid tetrapeptide (TAsp) as a precursor. Cu2+ mainly promoted the reaction of oxidants with TAsp (i.e., TAsp-induced decay) to produce DBPs, rather than self-decay of oxidants to generate BrO3‒ and ClO3‒. Cu2+ increased THMs yield, but decreased HANs yield due to the catalytic hydrolysis. Cu2+ was more prone to promote the reaction of TAsp with HOCl than with HOBr, leading to a DBPs shift from brominated to chlorinated species. The chemical characterizations of Cu2+-TAsp complexations demonstrate that Cu2+ combined with TAsp at the N and O sites in both amine and amide groups, and the intermediate identification suggests that Cu2+ enhanced the stepwise chlorination process by promoting the substitution of chlorine and the breakage of CC bonds. The effect of Cu2+ on THMs yield changed from promoting to inhibiting with the increase of pH, while that on HANs yield was inhibiting regardless of pH variation. Additionally, the impact of Cu2+ on the formation of DBPs was also affected by Cu2+ dose, Cl2/C ratio and Br- concentration. This study helps to understand the formation of EPS-derived DBPs in water pipes, and provides reference for formulating control strategies during biofilm outbreaks.

Bacterial communities of planktonic bacteria and mature biofilm in service lines and premise plumbing of a Megacity: Composition, Diversity, and influencing factors

Although simulated studies have provided valuable knowledge regarding the communities of planktonic bacteria and biofilms, the lack of systematic field studies have hampered the understanding of microbiology in real-world service lines and premise plumbing. In this study, the bacterial communities of water and biofilm were explored, with a special focus on the lifetime development of biofilm communities and their key influencing factors. The 16S rRNA gene sequencing results showed that both the planktonic bacteria and biofilm were dominated by Proteobacteria. Among the 15,084 observed amplicon sequence variants (ASVs), the 33 core ASVs covered 72.8 %, while the 12 shared core ASVs accounted for 62.2 % of the total sequences. Remarkably, it was found that the species richness and diversity of biofilm communities correlated with pipe age. The relative abundance of ASV2 (f_Sphingomonadaceae) was lower for pipe ages 40-50 years (7.9 %) than for pipe ages 10-20 years (59.3 %), while the relative abundance of ASV10 (f_Hyphomonadaceae) was higher for pipe ages 40-50 years (19.5 %) than its presence at pipe ages 20-30 years (1.9 %). The community of the premise plumbing biofilm had significantly higher species richness and diversity than that of the service line, while the steel-plastics composite pipe interior lined with polyethylene (S-PE) harbored significantly more diverse biofilm than the galvanized steel pipes (S-Zn). Interestingly, S-PE was enriched with ASV27 (g_Mycobacterium), while S-Zn pipes were enriched with ASV13 (g_Pseudomonas). Moreover, the network analysis showed that five rare ASVs, not core ASVs, were keystone members in biofilm communities, indicating the importance of rare members in the function and stability of biofilm communities. This manuscript provides novel insights into real-world service lines and premise plumbing microbiology, regarding lifetime dynamics (pipe age 10-50 years), and the influences of pipe types (premise plumbing vs. service line) and pipe materials (S-Zn vs. S-PE).

Occurrences and implications of pathogenic and antibiotic-resistant bacteria in different stages of drinking water treatment plants and distribution systems

Different stages of drinking water treatment plants (DWTPs) play specific roles in diverse contaminants' removal present in natural water sources. Although the stages are recorded to promote adequate treatment of water, the occurrence of pathogenic bacteria (PB) and antibiotic-resistant bacteria (ARB) in the treated water and the changes in their diversity and abundance as it passed down to the end users through the drinking water distribution systems (DWDSs), is a great concern, especially to human health. This could imply that the different stages and the distribution system provide a good microenvironment for their growth. Hence, it becomes pertinent to constantly monitor and document the diversity of PB and ARB present at each stage of the treatment and distribution system. This review aimed at documenting the occurrence of PB and ARB at different stages of treatment and distribution systems as well as the implication of their occurrence globally. An exhaustive literature search from Web of Science, Science-Direct database, Google Scholar, Academic Research Databases like the National Center for Biotechnology Information, Scopus, and SpringerLink was done. The obtained information showed that the different treatment stages and distribution systems influence the PB and ARB that proliferate. To minimize the human health risks associated with the occurrence of these PB, the present review, suggests the development of advanced technologies that can promote quick monitoring of PB/ARB at each treatment stage and distribution system as well as reduction of the cost of environomics analysis to promote better microbial analysis.

Microbial ecology of drinking water from source to tap

As drinking water travels from its source, through various treatment processes, hundreds to thousands of kilometres of distribution network pipes, to the taps in private homes and public buildings, it is exposed to numerous environmental changes, as well as other microbes living in both water and on surfaces. This review aims to identify the key locations and factors that are associated with changes in the drinking water microbiome throughout conventional urban drinking water systems from the source to the tap water. Over the past 15 years, improvements in cultivation-independent methods have enabled studies that allow us to answer such questions. As a result, we are beginning to move towards predicting the impacts of disturbances and interventions resulting ultimately in management of drinking water systems and microbial communities rather than mere observation. Many challenges still exist to achieve effective management, particularly within the premise plumbing environment, which exhibits diverse and inconsistent conditions that may lead to alterations in the microbiota, potentially presenting public health risks. Finally, we recommend the establishment of global collaborative projects on the drinking water microbiome that will enhance our current knowledge and lead to tools for operators and researchers alike to improve global access to high-quality drinking water.

Effects of water chemistry and flow on lead release from plastic pipes versus copper pipes, implications for plumbing decontamination

Despite being corrosion-resistant, plastic potable water pipes might accumulate heavy metals on their surface if they convey metal-contaminated tap water. This study examined the influence of water pH and flow conditions on lead (Pb) release from new and biofilm-laden potable water pipes to provide insights regarding decontamination. For this purpose, biofilms were grown onto new crosslinked polyethylene (PEX-A), high-density polyethylene (HDPE), and copper pipes for three months. Lead was then deposited onto the new and biofilm-laden pipes through 5 d exposure experiments under flow conditions. After that, lead release experiments were conducted by exposing the lead-accumulated pipes to lead-free synthetic tap water for 5 d, under both stagnant and water flow conditions. The metal accumulation study showed no significant difference in lead uptake by new pipes and their biofilm-laden counterparts under flow conditions. This could be attributed to the detachment of biofilms that have accumulated lead as water flows through the pipes. Water flow conditions significantly influenced the lead release from new and biofilm-laden water pipes. A lower water pH of 5.0 increased the release of lead from plastic pipes into the contact water, compared to pH 6.0 and 7.8. The greatest percentage of lead was released from biofilm-laden HDPE pipes (5.3%, 120 h) compared to biofilm-laden copper pipes (3.9%, 6 h) and PEX-A (3.7%, 120 h) and after exposure to lead-free synthetic tap water at pH 5.0, under stagnant conditions. On the other hand, under water flow conditions, the greatest lead release was found for new PEX-A pipes (4.4%, 120 h), new HDPE pipes (2.7%, 120 h), and biofilm-laden copper pipes (3.7%, 2 h).

Biofilm on the pipeline wall is an important transmission route of resistome in drinking water distribution system

Due to the intensive use of antibiotics, the drinking water distribution system (DWDS) has become one of the hotspots of antibiotic resistance. However, little is known about the role of biofilm in the aspect of spreading resistance in DWDS. In present study, four lab-scale biological annular reactors (BAR) were constructed to investigate the transmission of ARGs exposed to a certain amount of antibiotic (sulfamethoxazole) synergistic disinfectants. It was emphasized that pipe wall biofilm was an important way for ARGs to propagate in the pipeline, and the results were quantified by constructing an operational taxonomic unit (OTU) network map. The network analysis results showed the biofilm contribution to waterborne bacteria was finally estimated to be 51.45% and 34.27% in polyethylen (PE) pipe and ductile iron (DI) pipe, respectively. The proportion of vertical gene transfer (VGT) in biofilm was higher than that in water, and the occurrence of this situation had little relationship with the selection of pipe type. Overall, this study revealed how biofilm promoted the transmission of resistome in bulk water, which can provide insights into assessing biofilm-associated risks and optimizing pipe material selection for biofilm control in DWDS.

Culturing the Plastisphere: comparing methods to isolate culturable bacteria colonising microplastics

Microplastics quickly become colonised by diverse microbial communities, known as the Plastisphere. There is growing concern that microplastics may support the enrichment and spread of pathogenic or antimicrobial resistant microorganisms, although research to support the unique role of microplastics in comparison to control particles remains inconclusive. Limitations to this research include the microbiological methods available for isolating adhered microbes. Culture-based methods provide some of the most established, accessible and cost-effective microbiological protocols, which could be extremely useful in helping to address some of the remaining key questions in Plastisphere research. Previous works have successfully cultured bacteria from plastics, but these have not yet been reviewed, nor compared in efficiency. In this study, we compared four common biofilm extraction methods (swabbing, sonication, vortexing, sonication followed by vortexing) to extract and culture a mixed community of bacteria from both microplastic (polyethylene, polypropylene and polystyrene) and control (wood and glass) particles. Biofilm extraction efficiency and viability of bacterial suspension was determined by comparing CFU/mL of four different groups of bacteria. This was verified against optical density and 16S rRNA qPCR. Overall, we found that all tested methods were able to remove biofilms, but to varying efficiencies. Sonicating particles with glass beads for 15 min, followed by vortexing for a further minute, generated the highest yield and therefore greatest removal efficiency of culturable, biofilm-forming bacteria.

Zerovalent Iron/Cu Combined Degradation of Halogenated Disinfection Byproducts and Quantitative Structure-Activity Relationship Modeling

Previous studies have reported that zerovalent iron (ZVI) can reduce several aliphatic groups of disinfection byproducts (DBPs) (e.g., haloacetic acids and haloacetamides) effectively, and the removal efficiency can be significantly improved by metallic copper. Information regarding ZVI/Cu combined degradation of different types of halogenated DBPs can help understand the fate of overall DBPs in drinking water distribution and storage systems consisting of unlined cast iron/copper pipes and related potential control strategies. In this study, we found that, besides aliphatic DBPs, many groups of new emerging aromatic DBPs formed in chlorinated and chloraminated drinking water can be effectively degraded by ZVI/Cu; meanwhile, total organic halogen and total ion intensity were reduced significantly after treatment. Moreover, a robust quantitative structure-activity relationship model was developed and validated based on the ZVI/Cu combined degradation rate constants of 14 typical aromatic DBPs; it can predict the degradation rate constants of other aromatic DBPs for screening and comparative purposes, and the optimized descriptors indicate that DBPs possessing a lower value of the lowest unoccupied molecular orbital energy and a higher value of dipole moment tend to present higher degradation rate constants. In addition, toxicity data of 47 DBPs (belonging to 18 groups) were predicted by two previously established toxicity models, demonstrating that, although most DBPs exhibit higher toxicity than their dehalogenated products, some DBPs show lower toxicity than their lowly halogenated analogs.

A Critical Review on the Factors that Influence Opportunistic Premise Plumbing Pathogens: From Building Entry to Fixtures in Residences

Residential buildings provide unique conditions for opportunistic premise plumbing pathogen (OPPP) exposure via aerosolized water droplets produced by showerheads, faucets, and tubs. The objective of this review was to critically evaluate the existing literature that assessed the impact of potentially enhancing conditions to OPPP occurrence associated with residential plumbing and to point out knowledge gaps. Comprehensive studies on the topic were found to be lacking. Major knowledge gaps identified include the assessment of OPPP growth in the residential plumbing, from building entry to fixtures, and evaluation of the extent of the impact of typical residential plumbing design (e.g., trunk and branch and manifold), components (e.g., valves and fixtures), water heater types and temperature setting of operation, and common pipe materials (copper, PEX, and PVC/CPVC). In addition, impacts of the current plumbing code requirements on OPPP responses have not been assessed by any study and a lack of guidelines for OPPP risk management in residences was identified. Finally, the research required to expand knowledge on OPPP amplification in residences was discussed.

Phosphorus-rich biochar modified with Alcaligenes faecalis to promote U(VI) removal from wastewater: Interfacial adsorption behavior and mechanism

Phosphorus-rich biochar (PBC) has been extensively studied due to its significant adsorption effect on U(VI). However, the release of phosphorus from PBC into solution decreases its adsorption performance and reusability and causes phosphorus pollution of water. In this study, Alcaligenes faecalis (A. faecalis) was loaded on PBC to produce a novel biocomposite (A/PBC). After adsorption equilibrium, phosphorus released into solution from PBC was 2.32 mg/L, while it decreased to 0.34 mg/L from A/PBC (p < 0.05). The U(VI) removal ratio of A/PBC reached nearly 100%, which is 13.08% higher than that of PBC (p < 0.05), and it decreased only by 1.98% after 5 cycles. When preparing A/PBC, A. faecalis converted soluble phosphate into insoluble metaphosphate minerals and extracellular polymeric substances (EPS). And A. faecalis cells accumulated through these metabolites and formed biofilm attached to the PBC surface. The adsorption of metal cations on phosphate further contributed to phosphorus fixation in the biofilm. During U(VI) adsorption by A/PBC, A. faecalis synthesize EPS and metaphosphate minerals by using the internal components of PBC, thus increasing the abundance of acidic functional groups and promoting U(VI) adsorption. Hence, A/PBC can be a green and sustainable material for U(VI) removal from wastewater.

Electric-Inducive Microbial Interactions in a Thermophilic Anaerobic Digester Revealed by High-Throughput Sequencing of Micron-Scale Single Flocs

Although conductive materials have been shown to improve efficiency in anaerobic digestion (AD) by modifying microbial interactions, the interacting network under thermophilic conditions has not been examined. To identify the true taxon-taxon associations within thermophilic anaerobic digestion (TAD) microbiome and reveal the influence of carbon cloth (CC) addition, we sampled micron-scale single flocs (40-70 μm) randomly isolated from lab-scale thermophilic digesters. Results revealed that CC addition not only significantly boosted methane yield by 25.3% but also increased the spatial heterogeneity of the community in the sludge medium. After CC addition, an evident translocation of Pseudomonas from the medium to the biofilm was observed, showing their remarkable capacity for biofilm formation. Additionally, Clostridium and Thermotogaceae tightly aggregated and steadily co-occurred in the medium and biofilm of the TAD microbiome, which might be associated with their unique extracellular sugar metabolizing style. Finally, CC induced syntrophic interaction between Syntrophomonas and denitrifiers of Rhodocyclaceae. The upregulated respiration-associated electron transferring genes (Cyst-c, complex III) on the cellular membranes of these collaborating partners indicated a potential coupling of the denitrification pathway with syntrophic acetate oxidation via direct interspecies electron transfer (DIET). These findings provide an insight into how conductive materials promote thermophilic digestion performance and open the path for improved community monitoring of biotreatment systems.

Impact of Pipe Material and Temperature on Drinking Water Microbiome and Prevalence of Legionella, Mycobacterium, and Pseudomonas Species

In drinking water distribution systems (DWDSs), pipe material and water temperature are some of the critical factors affecting the microbial flora of water. Six model DWDSs consisting of three pipe materials (galvanized steel, copper, and PEX) were constructed. The temperature in three systems was maintained at 22 °C and the other 3 at 32 °C to study microbial and elemental contaminants in a 6-week survey using 16S rRNA next-generation sequencing (NGS) and inductively coupled plasma-optical emission spectrometry (ICP-OES). Pipe material and temperature were preferentially linked with the composition of trace elements and the microbiome of the DWDSs, respectively. Proteobacteria was the most dominant phylum across all water samples ranging from 60.9% to 91.1%. Species richness (alpha diversity) ranking was PEX < steel ≤ copper system and elevated temperature resulted in decreased alpha diversity. Legionellaceae were omni-prevalent, while Mycobacteriaceae were more prevalent at 32 °C (100% vs. 58.6%) and Pseudomonadaceae at 22 °C (53.3% vs. 62.9%). Heterogeneity between communities was disproportionately driven by the pipe material and water temperature. The elevated temperature resulted in well-defined microbial clusters (high pseudo-F index) in all systems, with the highest impact in PEX (10.928) followed by copper (9.696) and steel (5.448). Legionellaceae and Mycobacteriaceae are preferentially prevalent in warmer waters. The results suggest that the water temperature has a higher magnitude of impact on the microbiome than the pipe material.

Co-occurrence of phthalate esters and perfluoroalkyl substances affected bacterial community and pathogenic bacteria growth in rural drinking water distribution systems

The adverse health effects of phthalate esters (PAEs) and perfluoroalkyl substances (PFAS) in drinking water have attracted considerable attention. Our study investigated the effects of PAEs and PFAS on the bacterial community and the growth of potential human pathogenic bacteria in rural drinking water distribution systems. Our results showed that the total concentration of PAEs and PFAS ranged from 1.02 × 10² to 1.65 × 10⁴ ng/L, from 4.40 to 1.84 × 10² ng/L in rural drinking water of China, respectively. PAEs concentration gradually increased and PFAS slowly decreased along the pipeline distribution, compared to concentrations in the effluents of rural drinking water treatment plants. The co-occurrence of higher concentrations of PAEs and PFAS changed the structure and function of the bacterial communities found within these environments. The bacterial community enhanced their ability to respond to fluctuating environmental conditions through up-regulation of functional genes related to extracellular signaling and interaction, as well as genes related to replication and repair. Under these conditions, co-occurrence of PAEs and PFAS promoted the growth of potential human pathogenic bacteria (HPB), therefore increasing the risk of the development of associated diseases among exposed persons. The main HPB observed in this study included Burkholderia mallei, Mycobacterium tuberculosis, Klebsiella pneumoniae, Acinetobacter calcoaceticus, Escherichia coli, and Pseudomonas aeruginosa. Contaminants including particles, microorganisms, PAEs and PFAS were found to be released from corrosion scales and deposits of pipes and taps, resulting in the increase of the cytotoxicity and microbial risk of rural tap water. These results are important to efforts to improve the safety of rural drinking water.

Bacterial diversity across four drinking water distribution systems in Croatia: impacts of water management practices and disinfection by-products

Several factors may impact bacterial diversity in drinking water distribution systems (DWDSs) including the origin of the raw water, the water treatment technologies, and the disinfection practices applied. 16S rRNA metabarcoding was used for the in-depth characterization of bacterial communities in the four studied Croatian DWDSs (A, B, C, D) two of which had residual disinfectant (A, B) and two were without (C, D), while only B utilized the conventional water treatment technology. Significantly higher diversity and species richness were evidenced in non-disinfected DWDSs (p<0.05) compared to disinfected DWDSs. The phylum Proteobacteria was the most abundant in all the DWDSs, being proportionately higher in non-disinfected systems (p<0.05). The most abundant genera in DWDS-A Mycobacterium and Sphingomonas both positively correlated, whereas Lactobacillus negatively correlated with the concentration of disinfection by-products (DBPs) as a sum of haloacetic acids (HAAs). Conversely, the genus Ralstonia positively correlated with the individual DBP dichloroacetic acid. These results indicate that genera Sphingomonas, Mycobacterium, Lactobacillus and Ralstonia could have an effect on promoting the formation of DBPs, in a similar manner to how negatively correlated taxa may influence their degradation.

Emissions of Fungal Volatile Organic Compounds in Residential Environments and Temporal Emission Patterns: Implications for Sampling Methods

Currently, little is known about the occurrences of fungi-derived microbial volatile organic compounds (mVOCs) in various indoor materials and their detection in residential environments, despite mVOCs being linked to several acute health effects. We identified various mVOCs emitted from fungi grown on PVC wallpaper, silicone rubber, and malt extract agar. We also investigated mVOCs temporal emission and whether fungi-derived VOCs concentration can be used to estimate fungal concentration in the air using active and passive air sampling methods. Among the three fungal growth media included in this study, silicone rubber produced the most variety of mVOCs: 106 compounds (from Aspergillus niger), 35 compounds (from Alternaria alternata), and 85 compounds (from Penicillium chrysogenum). We also found the emission patterns of eight chemical classes (i.e., aromatics, ethers, aliphatics, alcohols, ketones, aldehydes, chlorides, and nitrides) from the three different fungi. From the results of our field experiments in 11 residential environments, passive air samplers led to higher correlations coefficients (0.08 to 0.86) between mVOCs' air concentrations and airborne fungal concentrations, compared with active air samplers, which showed negative correlation coefficients (-0.99 to -0.02) for most compounds. This study elucidated the occurrence and temporal emission patterns of fungal VOCs in residential environments.

Distribution, biological effects and biofilms of microplastics in freshwater systems - A review

The rapidly rising output and mass use of plastics have made plastics pollution a major environmental problem. Since plastics are persistent in the environment, understanding the migration transformation characteristics of plastics is critical. Given the ever-increasing concern about the environmental risks posed by microplastics, their prevalence, fate, abundance and impact have been intensively studied. Most of these investigations focused on the marine environment, but research on freshwater microplastics is less extensive. This article aims to briefly summarize the research progress of freshwater microplastics, identify existing gaps and draw novel conclusions, so as to provide useful information for the research of freshwater microplastics. Using the statistics and analysis of freshwater microplastics studies in 2016-2021, this review systematically discusses microplastics in globally freshwater systems. The biological effects of microplastics on freshwater organisms were discussed as well. Some potential ecological effects of microplastic biofilms were shown, such as climate change and material circulation. More importantly, we present some unique conclusions. For example, the detection of freshwater microplastics is mainly concentrated in natural freshwater systems, while few are concentrated in artificial freshwater systems. In addition, polystyrene is the main mode for testing the biological effects of freshwater microplastics, and polyethene and polypropylene which are the most common in freshwater environments, have not been taken seriously. We also pointed out that studies on advanced freshwater plants in the topic of biological effects of microplastics still need strengthen.

In situ analysis of copper speciation during in vitro digestion: Differences between copper in drinking water and food

In recent years, the safety of copper in drinking water has increasingly been questioned. Copper speciation is an important factor that affects its bioavailability and toxicity; thus, it is critical to investigate the speciation of copper that is ingested from food and drinking water during in vitro digestion. After digestion, water- and food-derived copper formed 60 ± 4% 0.1-1 kDa and 49 ± 6% 10-1,000 kDa copper complexes, respectively. Under simulated fasting drinking water conditions, up to 90 ± 2% 0.1-1 kDa copper complexes formed. In addition, using ion selective electrode analysis, water-derived copper was detected that contained higher Cu²⁺ concentrations after digestion than those of food-derived copper. These results indicate that water-derived copper forms smaller-sized species and exhibits higher Cu²⁺ concentrations during digestion than those of food-derived copper, thereby highlighting the importance of reassessing the safety limit for copper in drinking water.

Biofilm on microplastics in aqueous environment: Physicochemical properties and environmental implications

The excellent properties of plastics make them widely used all over the world. However, when plastics enter the environmental medium, microplastics will inevitably be produced due to physical, chemical and biological factors. Studies have shown that microplastics have been detected in terrestrial, aquatic and atmospheric environments. In addition, the presence of microplastics will provide a new artificial adhesion substrate for biofilms. It has been proved that the formation of biofilms could significantly change some properties of microplastics. Some studies have found that microplastics attached with biofilms have higher environmental risks and eco-toxicity. Therefore, considering the widespread existence of microplastics and the ecological risks of microplastic biofilms, the physical and chemical properties of biofilms on microplastics and their impact on microplastics in aqueous environment are worth reviewing. In this paper, we comprehensively reviewed representative studies in this area. Firstly, this study reviews that the existence of biofilms could change the transport and deposition of microplastics. Subsequently, the presence of biofilms would enhance the ability of microplastics to accumulate pollutant, such as persistent organic pollutants, heavy metals and antibiotics. Moreover, the effect of biofilms on microplastics enrichment of harmful microorganisms is summarized. Finally, some future research needs and strategies are proposed to better understand the problem of biofilms on microplastics.

Effects of pipe materials on the characteristic recognition, disinfection byproduct formation, and toxicity risk of pipe wall biofilms during chlorination in water supply pipelines

There are growing concerns over the contributions of biofilms to disinfection byproduct (DBP) formation in engineered water systems (EWSs). Three kinds of water supply pipes, ductile iron (DI), cement-lined stainless steel (SS) and polyethylene (PE) pipes, were selected for the experiment conducted in this study. Based on test results, the three pipe biofilms showed relatively obvious differences in growth, morphological characteristics, organic components and bacterial diversity. Secreted extracellular polymeric substance (EPS) accounted for more than 90% of the biofilm and had greater disinfection byproduct formation potential (DBPFP) than the cell phases. DI pipe wall biofilms had the highest DBPFP, which to a certain extent means that denser and richer organic matter can be produced as the precursor of different types of DBPs. UHPLC-Q Exactive was used to identify the types of DBPs generated from the chlorination of histidine (His), alanine (Ala) and tryptophan (Trp) shared by the three pipe materials and their formation pathways. Compared to carbonaceous disinfection by-products (C-DBPs), nitrogenous disinfection by-products (N-DBPs) had a significant advantage in toxicity generation potentials in the biofilms, especially dichloroacetonitrile (DCAN) and trichloronitromethane (TCNM). DCAN and haloacetic acids (HAAs) were the key to cytotoxicity in biofilms, while TCNM was dominant in biofilm genotoxicity.

Microplastics as a vehicle of heavy metals in aquatic environments: A review of adsorption factors, mechanisms, and biological effects

Microplastics (MPs) have recently attracted much attention due to their widespread distribution in the aquatic environment. Microplastics can act as a vector of heavy metals in the aquatic environment, causing a potential threat to aquatic organisms and human health. This review mainly summarized the occurrence of microplastics in the aquatic environment and their interaction with heavy metals. Then, we considered the adsorption mechanisms of MPs and heavy metals, and further critically discussed the effects of microplastics properties and environmental factors (e.g., pH, DOM, and salinity) on the adsorption of heavy metals. Finally, the potential risks of combined exposure of MPs and heavy metals to aquatic biota were briefly evaluated. This work aims to provide a theoretical summary of the interaction between MPs and heavy metals, and is expected to serve as a reference for the accurate assessment of their potential risks in future studies.

Structure and Functional Attributes of Bacterial Communities in Premise Plumbing Across the United States

Microbes that thrive in premise plumbing can have potentially important effects on human health. Yet, how and why plumbing-associated microbial communities vary across broad spatial scales remain undetermined. We characterized the bacterial communities in 496 showerheads collected from across the continental United States. The overall community structure, determined by 16S rRNA gene amplicon sequencing, revealed high levels of bacterial diversity. Although a large fraction of the observed variation in community composition could not be explained, differences in bacterial community composition were associated with water supply (private well water vs public municipal water), water source (groundwater vs surface water), and associated differences in water chemistry (pH and chlorine). Most notably, showerheads in homes supplied with public water had higher abundances of Blastomonas, Mycobacterium, and Porphyrobacter, while Pseudorhodoplanes, Novosphingobium, and Nitrospira were more abundant in those receiving private well water. We conducted shotgun metagenomic analyses on 92 of these samples to assess differences in genomic attributes. Public water-sourced showerheads had communities enriched in genes related to lipid and xenobiotic metabolisms, virulence factors, and antibiotic resistance. In contrast, genes associated with oxidative stress and membrane transporters were over-represented in communities from private well water-sourced showerheads compared to those supplied by public water systems. These results highlight the broad diversity of bacteria found in premise plumbing across the United States and the role of the water source and treatment in shaping the microbial community structure and functional potential.

The influence of gastrointestinal pH on speciation of copper in simulated digestive juice

Speciation can provide knowledge about absorption, reactivity to binding sites, bioavailability, toxicity, and excretion of elements. In this study, the speciation of copper in different model solutions under the influence of gastrointestinal (GI) pH was studied by ion selective electrode (ISE) and inductively coupled plasma optical emission spectrometry (ICP OES). It was found that the electrode response (mV) against Cu2+ decreased with the increase in pH and dropped to the lowest point at pH 7.5 in all model solutions. When amino acids and organic acids were present, the ratio of filtered copper (0.45 μm, pH 7.5) was more than 90%. When casein was present, whey protein, pancreatin, and starch were added, and the ratio of filtered copper was 85.6 ± 0.3, 56.7 ± 8.8, 38.5 ± 5.1, and 1.0 ± 0.3%, respectively. When there is not enough organic ligand, excessive copper will form copper hydroxide precipitation with the increase in pH, but it got the highest electrode response (mV) against Cu2+. From this study, it can be concluded that the speciation of copper in GI tract is strongly influenced by the pH and the composition of food. When there are few ligands coexisting in the GI tract, the concentration of copper ion may be relatively high.

Unified Metallic Catalyst Aging Strategy and Implications for Water Treatment

Heterogeneous catalysis holds great promise for oxidizing or reducing a range of pollutants in water. A well-recognized, but understudied, barrier to implement catalytic treatment centers around fouling or aging over time of the catalyst surfaces. To better understand how to study catalyst fouling or aging, we selected a representative bimetallic catalyst (Pd-In supported on Al2O3), which holds promise to reduce nitrate to innocuous nitrogen gas byproducts upon hydrogen addition, and six model solutions (deionized water, sodium hypochlorite, sodium borohydride, acetic acid, sodium sulfide, and tap water). Our novel aging experimental apparatus permitted single passage of each model solution, separately, through a small packed-bed reactor containing replicate bimetallic catalyst "beds" that could be sacrificed weekly for off-line characterization to quantify impacts of fouling or aging. The composition of the model solutions led to the following gradual changes in surface composition, morphology, or catalytic reactivity: (i) formation of passivating species, (ii) decreased catalytic sites due to metal leaching under acid conditions or sulfide poisoning, (iii) dissolution and/or transformation of indium, (iv) formation of new catalytic sites by the introduction of an additional metallic element, and (v) oxidative etching. The model solution water chemistry captured a wide range of conditions likely to be encountered in potable or industrial water treatment. Aging-induced changes altered catalytic activity and provided insights into potential strategies to improve long-term catalyst operations for water treatment.

Microbial community and antibiotic resistance genes of biofilm on pipes and their interactions in domestic hot water system

This study aimed to explore the dynamics of microbial communities and antibiotic resistance genes (ARGs) during biofilm formation on polypropylene random (PPR), polyvinyl chloride and stainless steel pipes in domestic hot water system (DHWS), as well as their interactions. Full-scale classification was used to divide abundant and rare genera with 0.1% and 1% as the thresholds. The biofilm community structure presented a temporal pattern, which was mainly determined by conditionally rare or abundant taxa (CRAT) and conditionally rare taxa (CRT). The dynamics of microbial community during biofilm formation were observed, and the effect of pipe material on conditionally abundant taxa (CAT) and CRAT was greater than CRT and rare taxa (RT). CRAT showed the most complex internal associations and were identified as the core taxa. Notably, CRT and RT with low relative abundance, also played an important role in the network. For potential pathogens, 17 genera were identified in this study, and their total relative abundance was the highest (3.6-28.9%) in PPR samples. Enterococcus of CRAT was the dominant potential pathogen in young biofilms. There were 36 more co-exclusion patterns (140) observed between potential pathogens and nonpathogenic bacteria than co-occurrence (104). A total of 38 ARGs were predicted, and 109 negative and 165 positive correlations were detected between them. Some potential pathogens (Escherichia/Shigella and Burkholderia) and nonpathogenic bacteria (Meiothermus and Sphingopyxis) were identified as the possible hosts of ARGs. This study is helpful for a comprehensive understanding of the biofilm microbial community and ARGs, and provides a reference for the management and biosafety guarantee of newly-built DHWS.

Microscopic techniques to evaluate the biofilm formation ability of a marine bacterium Pseudomonas aeruginosa PFL-P1 on different substrata

Biofilm formation in bacteria is strongly affected by the nature of substrata. Different substrata such as glass, polystyrene, steel, ceramic, and rubber were used to assess the biofilm forming ability of a marine bacterium Pseudomonas aeruginosa PFL-P1 using a scanning electron microscope (SEM), atomic force microscope (AFM), and confocal laser scanning microscope (CLSM). The bacterium formed dense biofilms with varied aggregation on different substrata. SEM study revealed small rod-shaped cells with diverse arrangements within the biofilms on all the substrata under study. The AFM study revealed the highest roughness of 545 nm on the ceramic substratum. The biofilms formed on ceramic substratum were characterized with maximum roughness (742 nm), maximum peak height (1,480 nm), and maximum arithmetic mean height (611 nm), significantly higher than all the other substrata (p < .05). AFM studies confirmed that P. aeruginosa PFL-P1 exhibited biofilm heterogeneity on all the substrata. The CLSM study indicated a higher fraction of nucleic acids to α-polysaccharides ratio in the biofilms. COMSTAT analysis revealed the highest biofilm biomass of ~18 μm³ /μm² on the ceramic substratum. The maximum biofilm thickness of ~50 μm in the native state on the ceramic substratum was significantly higher than glass (p = .0015), polystyrene (p = .0001), steel (p = .0035), and rubber substrata (p = .0001). The higher surface roughness of ceramic substratum is accountable for more area for colonization, as evident from higher biomass and thickness of the biofilm. This study provides insight into the substratum properties, which modulate the biofilm forming ability in bacteria.

Initial adhesion suppression of biofilm-forming and copper-tolerant bacterium Variovorax sp. on laser microtextured copper surfaces

The growth of detrimental biofilms on metal surfaces affects their structural performance and lifespan. Microtopographic texturization has emerged as an approach to suppress biofilm growth by preventing the initial stages of bacterial adhesion. This work studies the effects of linear pattern copper texturization on the initial adhesion steps of the biofilm-forming and copper-resistant bacterium Variovorax sp. Linear patterns with 4.7, 6.8, 14, and 18 μm periodicity were produced by direct laser interference patterning (DLIP) on copper coupons. Surface features were characterized by microscopic and spectroscopic techniques, and bacterial adhesion behavior was characterized by epifluorescence microscopy and functionalization of atomic force microscopy tips. We found a periodicity of 4.7 μm as the most efficient pattern to suppress Variovorax sp. initial adhesion by 31.1 % with respect to the nontextured surface. Preferential settlement in hummocks over hollows was observed for patterns with 14 and 18 μm periodicity, with adhesion events showing higher frequency in these topographies than patterns with periodicities of 4.7 and 6.8 μm. Our results highlight an understanding of the initial bacteria-copper adhesion and settlement behavior, thus contributing to the potential development of innocuous strategies for controlling biofilm growth on copper-based materials.

Copper Surfaces in Biofilm Control

Biofilms are structures comprising microorganisms associated to surfaces and enclosed by an extracellular polymeric matrix produced by the colonizer cells. These structures protect microorganisms from adverse environmental conditions. Biofilms are typically associated with several negative impacts for health and industries and no effective strategy for their complete control/eradication has been identified so far. The antimicrobial properties of copper are well recognized among the scientific community, which increased their interest for the use of these materials in different applications. In this review the use of different copper materials (copper, copper alloys, nanoparticles and copper-based coatings) in medical settings, industrial equipment and plumbing systems will be discussed considering their potential to prevent and control biofilm formation. Particular attention is given to the mode of action of copper materials. The putative impact of copper materials in the health and/or products quality is reviewed taking into account their main use and the possible effects on the spread of antimicrobial resistance.

Investigate the role of biofilm and water chemistry on lead deposition onto and release from polyethylene: An implication for potable water pipes

In this study, the influence of biofilm presence and water chemistry conditions on lead (Pb) deposition onto low density polyethylene (LDPE) surface was examined. The results demonstrated that biofilm presence on LDPE surfaces strongly and significantly enhanced Pb uptake, with the 13-fold greater equilibrium Pb surface loading when biofilm was present (1602 μg/m²) compared to the condition when it was absent (124 μg/m²). The kinetics of Pb adsorption onto LDPE surface when biofilm was present is best described by Pseudo 2nd order kinetic model. Pb adsorption onto new LDPE surfaces was significantly reduced from 1101 μg/m² to 134 μg/m² with increased aqueous solution's ionic strength from 3 × 10^-6 M to 0.0072 M. The presence of chlorine residual (2 mg/L) significantly reduced Pb adsorption onto LDPE surfaces by possible oxidation of Pb²⁺ to Pb⁴⁺ species. The kinetics of Pb release from LDPE surfaces was investigated under static and dynamic conditions through immediate exposure of Pb accumulated LDPE pellets to the synthetic water at pH 5.0 and 7.8. The results demonstrated a greater Pb release (86 %) at pH 5.0 compared to the pH 7.8 (58 %). An enhanced Pb release into the contact water was found under dynamic conditions compared to static conditions.

Inactivation of RNA and DNA viruses in water by copper and silver ions and their synergistic effect

Cu and Ag have been used as bactericidal agents since ancient times, yet their antiviral capacity in water remains poorly understood. This study tested the effect of copper (Cu) and silver (Ag) on model RNA and DNA viruses MS2 and PhiX 174 in solution at pH 6-8. Cu caused MS2 inactivation with similar rates at pH 6 and 7 but was inert towards PhiX 174 regardless of pH. Ag inactivated both viruses, causing denaturation of MS2 and loss of capsid spikes in PhiX 174. Ag inactivation rates were pH dependent and increased with increasing pH. At pH 8, 6.5 logs of PhiX were inactivated after 3 h and 3 logs of MS2 after only 10 min. The combined use of Cu and Ag revealed synergy in disinfecting MS2 at pH ≥ 7. Although metal concentrations used were higher than the desired values for drinking water treatment, the results prove a promising potential of Cu and Ag combinations as efficient viricidal agents.

Physics Comes to the Aid of Medicine-Clinically-Relevant Microorganisms through the Eyes of Atomic Force Microscope

Despite the hope that was raised with the implementation of antibiotics to the treatment of infections in medical practice, the initial enthusiasm has substantially faded due to increasing drug resistance in pathogenic microorganisms. Therefore, there is a need for novel analytical and diagnostic methods in order to extend our knowledge regarding the mode of action of the conventional and novel antimicrobial agents from a perspective of single microbial cells as well as their communities growing in infected sites, i.e., biofilms. In recent years, atomic force microscopy (AFM) has been mostly used to study different aspects of the pathophysiology of noninfectious conditions with attempts to characterize morphological and rheological properties of tissues, individual mammalian cells as well as their organelles and extracellular matrix, and cells’ mechanical changes upon exposure to different stimuli. At the same time, an ever-growing number of studies have demonstrated AFM as a valuable approach in studying microorganisms in regard to changes in their morphology and nanomechanical properties, e.g., stiffness in response to antimicrobial treatment or interaction with a substrate as well as the mechanisms behind their virulence. This review summarizes recent developments and the authors’ point of view on AFM-based evaluation of microorganisms’ response to applied antimicrobial treatment within a group of selected bacteria, fungi, and viruses. The AFM potential in development of modern diagnostic and therapeutic methods for combating of infections caused by drug-resistant bacterial strains is also discussed.

Critical Review: Propensity of Premise Plumbing Pipe Materials to Enhance or Diminish Growth of Legionella and Other Opportunistic Pathogens

Growth of Legionella pneumophila and other opportunistic pathogens (OPs) in drinking water premise plumbing poses an increasing public health concern. Premise plumbing is constructed of a variety of materials, creating complex environments that vary chemically, microbiologically, spatially, and temporally in a manner likely to influence survival and growth of OPs. Here we systematically review the literature to critically examine the varied effects of common metallic (copper, iron) and plastic (PVC, cross-linked polyethylene (PEX)) pipe materials on factors influencing OP growth in drinking water, including nutrient availability, disinfectant levels, and the composition of the broader microbiome. Plastic pipes can leach organic carbon, but demonstrate a lower disinfectant demand and fewer water chemistry interactions. Iron pipes may provide OPs with nutrients directly or indirectly, exhibiting a high disinfectant demand and potential to form scales with high surface areas suitable for biofilm colonization. While copper pipes are known for their antimicrobial properties, evidence of their efficacy for OP control is inconsistent. Under some circumstances, copper's interactions with premise plumbing water chemistry and resident microbes can encourage growth of OPs. Plumbing design, configuration, and operation can be manipulated to control such interactions and health outcomes. Influences of pipe materials on OP physiology should also be considered, including the possibility of influencing virulence and antibiotic resistance. In conclusion, all known pipe materials have a potential to either stimulate or inhibit OP growth, depending on the circumstances. This review delineates some of these circumstances and informs future research and guidance towards effective deployment of pipe materials for control of OPs.

Use of Newly Designed Primers for Quantification of Complete Ammonia-Oxidizing (Comammox) Bacterial Clades and Strict Nitrite Oxidizers in the Genus Nitrospira

Complete ammonia-oxidizing (comammox) bacteria play key roles in environmental nitrogen cycling and all belong to the genus Nitrospira, which was originally believed to include only strict nitrite-oxidizing bacteria (sNOB). Thus, differential estimation of sNOB abundance from that of comammox Nitrospira has become problematic, since both contain nitrite oxidoreductase genes that serve as common targets for sNOB detection. Herein, we developed novel comammox Nitrospira clade A- and B-specific primer sets targeting the α-subunit of the ammonia monooxygenase gene (amoA) and a sNOB-specific primer set targeting the cyanase gene (cynS) for quantitative PCR (qPCR). The high coverage and specificity of these primers were checked by use of metagenome and metatranscriptome data sets. Efficient and specific amplification with these primers was demonstrated using various environmental samples. Using the newly designed primers, we successfully estimated the abundances of comammox Nitrospira and sNOB in samples from two chloramination-treated drinking water systems and found that, in most samples, comammox Nitrospira clade A was the dominant type of Nitrospira and also served as the primary ammonia oxidizer. Compared with other ammonia oxidizers, comammox Nitrospira had a higher abundance in process water samples in these two drinking water systems. We also demonstrated that sNOB can be readily misrepresented by an earlier method, calculated by subtracting the comammox Nitrospira abundance from the total Nitrospira abundance, especially when the comammox Nitrospira proportion is relatively high. The new primer sets were successfully applied to comammox Nitrospira and sNOB quantification, which may prove useful in understanding the roles of Nitrospira in nitrification in various ecosystems.IMPORTANCENitrospira is a dominant nitrite-oxidizing bacterium in many artificial and natural environments. The discovery of complete ammonia oxidizers in the genus Nitrospira prevents the use of previously identified primers targeting the Nitrospira 16S rRNA gene or nitrite oxidoreductase (nxr) gene for differential determination of strict nitrite-oxidizing bacteria (sNOB) in the genus Nitrospira and among comammox bacteria in this genus. We designed three novel primer sets that enabled quantification of comammox Nitrospira clades A and B and sNOB with high coverage, specificity, and accuracy in various environments. With the designed primer sets, sNOB and comammox Nitrospira were differentially estimated in drinking water systems, and we found that comammox clade A predominated over sNOB and other ammonia oxidizers in process water samples. Accurate quantification of comammox Nitrospira and sNOB by use of the newly designed primers will provide essential information for evaluating the contribution of Nitrospira to nitrification in various ecosystems.

A copper-specific microbial fuel cell biosensor based on riboflavin biosynthesis of engineered Escherichia coli

Copper pollution poses a serious threat to the aquatic environment; however, in situ analytical methods for copper monitoring are still scarce. In the current study, Escherichia coli Rosetta was genetically modified to express OprF and ribB with promoter P_t7 and P_cusC , respectively, which could synthesize porin and senses Cu²⁺ to produce riboflavin. The cell membrane permeability of this engineered strain was increased and its riboflavin production (1.45-3.56 μM) was positively correlated to Cu²⁺ (0-0.5 mM). The biosynthetic strain was then employed in microbial fuel cell (MFC) based biosensor. Under optimal operating parameters of pH 7.1 and 37°C, the maximum voltage (248, 295, 333, 352, and 407 mV) of the constructed MFC biosensor showed a linear correlation with Cu²⁺ concentration (0.1, 0.2, 0.3, 0.4, 0.5 mM, respectively; R²  = 0.977). The continuous mode testing demonstrated that the MFC biosensor specifically senses Cu²⁺ with calculated detection limit of 28 μM, which conforms to the common Cu²⁺ safety standard (32 μM). The results obtained with the developed biosensor system were consistent with the existing analytical methods such as colorimetry, flame atomic absorption spectrometry, and inductively coupled plasma optical emission spectrometry. In conclusion, this MFC-based biosensor overcomes the signal conversion and transmission problems of conventional approaches, providing a fast and economic analytical alternative for in situ monitoring of Cu²⁺ in water.

Chlorine Disinfection of Legionella spp., L. pneumophila, and Acanthamoeba under Warm Water Premise Plumbing Conditions

Premise plumbing conditions can contribute to low chlorine or chloramine disinfectant residuals and reactions that encourage opportunistic pathogen growth and create risk of Legionnaires' Disease outbreaks. This bench-scale study investigated the growth of Legionella spp. and Acanthamoeba in direct contact with premise plumbing materials-glass-only control, cross-linked polyethylene (PEX) pipe, magnesium anode rods, iron pipe, iron oxide, pH 10, or a combination of factors. Simulated glass water heaters (SGWHs) were colonized by Legionella pneumophila and exposed to a sequence of 0, 0.1, 0.25, and 0.5 mg/L chlorine or chloramine, at two levels of total organic carbon (TOC), over 8 weeks. Legionella pneumophila thrived in the presence of the magnesium anode by itself and or combination with other factors. In most cases, 0.5 mg/L Cl2 caused a significant rapid reduction of L. pneumophila, Legionella spp., or total bacteria (16S rRNA) gene copy numbers, but at higher TOC (>1.0 mg C/L), a chlorine residual of 0.5 mg/L Cl2 was not effective. Notably, Acanthamoeba was not significantly reduced by the 0.5 mg/L chlorine dose.

Replicable simulation of distal hot water premise plumbing using convectively-mixed pipe reactors

A lack of replicable test systems that realistically simulate hot water premise plumbing conditions at the laboratory-scale is an obstacle to identifying key factors that support growth of opportunistic pathogens (OPs) and opportunities to stem disease transmission. Here we developed the convectively-mixed pipe reactor (CMPR) as a simple reproducible system, consisting of off-the-shelf plumbing materials, that self-mixes through natural convective currents and enables testing of multiple, replicated, and realistic premise plumbing conditions in parallel. A 10-week validation study was conducted, comparing three pipe materials (PVC, PVC-copper, and PVC-iron; n = 18 each) to stagnant control pipes without convective mixing (n = 3 each). Replicate CMPRs were found to yield consistent water chemistry as a function of pipe material, with differences becoming less discernable by week 9. Temperature, an overarching factor known to control OP growth, was consistently maintained across all 54 CMPRs, with a coefficient of variation <2%. Dissolved oxygen (DO) remained lower in PVC-iron (1.96 ± 0.29 mg/L) than in PVC (5.71 ± 0.22 mg/L) or PVC-copper (5.90 ± 0.38 mg/L) CMPRs as expected due to corrosion. Further, DO in PVC-iron CMPRs was 33% of that observed in corresponding stagnant pipes (6.03 ± 0.33 mg/L), demonstrating the important role of internal convective mixing in stimulating corrosion and microbiological respiration. 16S rRNA gene amplicon sequencing indicated that both bulk water (P_adonis = 0.001, R² = 0.222, P_betadis = 0.785) and biofilm (P_adonis = 0.001, R² = 0.119, P_betadis = 0.827) microbial communities differed between CMPR versus stagnant pipes, consistent with creation of a distinct ecological niche. Overall, CMPRs can provide a more realistic simulation of certain aspects of premise plumbing than reactors commonly applied in prior research, at a fraction of the cost, space, and water demand of large pilot-scale rigs.

Corroding copper and steel exposed to intermittently flowing tap water promote biofilm formation and growth of Legionella pneumophila

The information about the impact of copper pipes on the growth of Legionella pneumophila in premise plumbing is controversial. For this reason, pipe segments of copper, stainless steel (SS), mild steel (MS), polyethylene, chlorinated polyvinylchloride (CPVC) and glass (controls) were exposed to intermittently flowing (20 min stagnation time) nonchlorinated tap water of 37 °C or 16 °C (ambient temperature) during six months to study the impact of metals on biofilm formation and growth of L. pneumophila. Biofilm concentrations (BfC, measured as ATP) on copper were 3 (at 37 °C) to 6 (at 16 °C) times higher than on SS. The maximum colony counts of L. pneumophila on the materials tested at 37 °C showed a quadratic relationship with the associated BfCs, with highest values on copper and MS. The average Cu concentration on the glass control of copper (glass-copper) was more than two log units lower than the Fe concentration on glass-MS, suggesting that copper released less corrosion by-products than MS. The release of corrosion by-products with attached biomass from MS most likely enhanced biofilm formation on glass-MS. Cloning and 16S RNA gene sequence analysis of the predominating biofilm bacteria revealed that an uncultured Xanthobacteraceae bacterium and Reyranella accounted for 75% of the bacterial community on copper at 37 °C. The nitrite-oxidizing Nitrospira moscoviensis, which can also utilize hydrogen (H₂) and formate, accounted for >50% of the bacterial abundance in the biofilms on MS and glass-MS at 37 °C. The predominating presence of the strictly anaerobic non-fermentative Fe(III)-reducing Geobacter and the Fe(II)-oxidizing Gallionella on MS exposed to tap water of 16 °C indicated anoxic niches and the availability of H₂, low molecular weight carboxylic acids (LMWCAs) and Fe(II) at the MS surface. LMWCAs likely also promoted bacterial growth on copper, but the release mechanisms from natural organic matter at the surface of corroding metals are unclear. The effects of water stagnation time and flow dynamics on biofilm formation on copper requires further investigation.

Investigation of nitrogen pollutants transformation and its pathways along the long-distance prechlorinated raw water distribution system

Understanding the transformation pattern of nitrogen (N) pollutants and its pathways in the prechlorinated raw water distribution system (PRWDS) is vital for controlling the stablitiy and safety of raw water qulity. This study investigated the N transformation, N functional genes and their correlations to find the N transformation pathways along the PRWDS. Results suggested that simultaneous nitrification, anaerobic ammonium oxidation and denitrification (SNAD) contribute to the N transformationin the PRWDS. Along the pipeline, anammox 16S rRNA (9.18 × 10⁷-8.41 × 10⁸ copies/g), limited by prechlorination, was the most abundant N functional genes and anammox process was the main pathway of ammonia nitrogen (NH₄⁺-N). The decreasing NH₄⁺-N was connected with Planctomycetes, Nitrospira and abundance of nxrA attributing to the joint effort of anammox and declined nitrification. The concentration of nitrate (NO₃^--N) increasing at first and then decreasing, was correlated positively with Sphingomonas. because of the declined nitritication and increased denitrification. Besides, the NO₃^--N→NO₂^--N process was considered to be primary NO₃^--N transformation pathways. Increases in the concentration of dissolved organic nitrogen (DON) and nitrite (NO₂^--N) observed in the PRWDS had positive correlation with relative abundance of Pseudomonas. We believe that prechlorination shaped the particular bacterialcharacteristics in biofilms and influenced the N transformation pathways indirectly, resulting in the varying N transformation rules in PRWDSs. Moreover, systematic and extended research is particularly vital for determining the effects of changes in source water quality and environmental conditions on bacterial community structure and N conversion along PRWDSs.