Novel approaches for studying pulmonary toxicity in vitro

The Actual Toxicity of Engine Exhaust Gases Emitted from Vehicles: The Development and Perspectives of Biological and Chemical Measurement Methods

Most of the current studies on vehicle engine exhaust emissions are focused on qualitative and quantitative measurements. Approval tests for admitting vehicles to traffic and tests performed at vehicle inspection stations are limited to measuring the concentrations of individual compounds or selected groups of compounds. For vehicles with compression-ignition engines, the annual emission control comprises only an exhaust gas opacity test, performed with an opacimeter. This approach does not consider very harmful groups of compounds that determine the toxicity of exhaust gases but are not directly covered by the emission standards, such as polycyclic aromatic hydrocarbons and volatile organic compounds. Also, it does not provide a clear answer to the question of the actual toxicity of exhaust gases, understood as the harmful effect that a given substance causes on living organisms or biological processes. Studies on the actual toxicity of engine exhaust gases present a new area of interest, increasingly more discussed but still not approached in a comprehensive way. The studies include experiments using in vitro biological methods and chemical analyses of gas mixtures. In this Review, I present an overview of current research and a critical comparison of commonly used methods of testing engine exhaust emissions and methods that might supplement them in a significant manner. The development of in vitro biological methods, including methods of microscopic analysis of cells in the assessment of exhaust gas toxicity, provides an innovative approach to the problem of air pollution. This type of research presents the opportunity to indisputably answer the question of the actual toxicity of a given gas mixture and to make a new contribution to science in the field of molecular biology. Current data show that the survival of cells exposed to engine exhaust emissions from older generation vehicles is higher compared to that of newer generation vehicles.

Diesel exhaust particles exposure induces liver dysfunction: Exploring predictive potential of human circulating microRNAs signature relevant to liver injury risk

Diesel exhaust particles (DEP) pollution should be taken seriously because it is an extensive environmental and occupational health concern. Exploring early effect biomarkers is crucial for monitoring and managing DEP-associated health risk assessment. Here, we found that serum levels of 67 miRNAs were dysregulated in DEP exposure group. Notably, 20 miRNAs were identified as each having a significant dose-response relationship with the internal exposure level of DEP. Further, we revealed that the DEP exposure could affect the liver function of subjects and that 7 miRNAs (including the well-known liver injury indicator, miR-122-5p) could serve as the novel epigenetic-biomarkers (epi-biomarkers) to reflect the liver-specific response to the DEP exposure. Importantly, an unprecedented prediction model using these 7 miRNAs was established for the assessment of DEP-induced liver injury risk. Finally, bioinformatic analysis indicated that the unique set of miRNA panel in serum might also contribute to the molecular mechanism of DEP exposure-induced liver damage. These results broaden our understanding of the adverse health outcomes of DEP exposure. Noteworthy, we believe this study could shed light on roles and functions of epigenetic biomarkers from environmental exposure to health outcomes by revealing the full chain of exposure-miRNAs-molecular pathways-disease evidence.

Assessment of the Actual Toxicity of Engine Exhaust Gas Emissions from Euro 3 and Euro 6 Compliant Vehicles with the BAT-CELL Method Using In Vitro Tests

Legal restrictions on vehicle engine exhaust gas emission control do not always go hand in hand with an actual reduction in the emissions of toxins into the atmosphere. Moreover, the methods currently used to measure exhaust gas emissions do not give unambiguous results on the impact of the tested gases on living organisms. The method used to assess the actual toxicity of gases, BAT-CELL Bio-Ambient-Tests using in vitro tests, takes into account synergistic interactions of individual components of a mixture of gases without the need to know its qualitative and quantitative composition and allows for determination of the actual toxicity of the gas composition. Using the BAT-CELL method, exhaust gases from passenger vehicles equipped with spark-ignition engines complying with the Euro 3 and Euro 6 emission standards were tested. The results of toxicological tests were correlated with the results of chromatographic analysis. It was shown that diverse qualitative composition of the mixture of hydrocarbons determining the exhaust gases toxicity may decrease the percentage value of cell survival. Additionally, it was proven that the average survival of cells after exposure to exhaust gases from tested vehicles meeting the more restrictive Euro 6 standard was lower than for vehicles meeting the Euro 3 standard thus indicating the higher toxicity of exhaust gases from newer vehicles.

Development, qualification, validation and application of the Ames test using a VITROCELL® VC10® smoke exposure system

•

Smoke-induced mutagenicity at air agar interface was developed and validated.

•

The VITROCELL^® VC10^® system was validated by equipment qualification protocols.

•

Differentiation of mutagenicity by 3R4F and Eclipse cigarettes was demonstrated.

The Ames test has established use in the assessment of potential mutagenicity of tobacco products but has generally been performed using partitioned exposures (e.g. total particulate matter [TPM], gas vapor phase [GVP]) rather than whole smoke (WS). The VITROCELL^®VC10^® smoke exposure system offers multiple platforms for air liquid interface (ALI), or air agar interface (AAI) in the case of the Ames test exposure to mimic in vivo-like conditions for assessing the toxicological impact of fresh WS in in vitro assays.

The goals of this study were to 1) qualify the VITROCELL^®VC10^® to demonstrate functionality of the system, 2) develop and validate the Ames test following WS exposure with the VITROCELL^®VC10^® and 3) assess the ability of the Ames test to differentiate between a reference combustible product (3R4F Kentucky reference cigarette) and a primarily tobacco heating product (Eclipse). Based on critical function assessments, the VITROCELL^®VC10^® was demonstrated to be fit for the purpose of consistent generation of WS. Assay validation was conducted for 5 bacterial strains (TA97, TA98, TA100, TA1535 and TA102) and reproducible exposure–related changes in revertants were observed for TA98 and TA100 in the presence of rat liver S-9 following exposure to 3R4F WS. In the comparative studies, exposure-related changes in in vitro mutagenicity following exposure of TA98 and TA100 in the presence of S9 to both 3R4F and Eclipse WS were observed, with the response for Eclipse being significantly less than that for 3R4F (p < 0.001) which is consistent with the fewer chemical constituents liberated by primarily-heating the product.

In vitro exposure of nasal epithelial cells to atmospheric dust

Dust storms are common phenomena in many parts of the world, and significantly increase the level of atmospheric particulate matter (PM). The soil-derived dust is a mixture of organic and inorganic particles and even remnants of pesticides from agricultural areas nearby. The risk of human exposure to atmospheric dust is well documented, but very little is known on the impact of inhaled PM on the biological lining of the nasal cavity, which is the natural filter between the external environment and the respiratory tract. We developed a new system and methodology for in vitro exposure of cultured nasal epithelial cells (NEC) to atmospheric soil-dust pollutants under realistic and controlled laboratory simulations that mimic nasal breathing. We exposed cultured NEC to clean and dust-polluted airflows that mimic physiological conditions. The results revealed that the secretion of mucin and IL-8 from the NEC exposed to clean and dust-polluted airflows was less than the secretion at static conditions under clean air. The secretion of IL-8 from NEC exposed to dust-polluted air was larger than that of clean air, but not larger than in the static case. The experiments with dust air pollution that also contained agricultural pesticides did not reveal differences in the secretion of mucin and IL-8 as compared to the same pollution without pesticides.

A simple cell transport device keeps culture alive and functional during shipping

Transporting living complex cellular constructs through the mail while retaining their full viability and functionality is challenging. During this process, cells often suffer from exposure to suboptimal life-sustaining conditions (e.g. temperature, pH), as well as damage due to shear stress. We have developed a transport device for shipping intact cell/tissue constructs from one facility to another that overcomes these obstacles. Our transport device maintained three different cell lines (Caco2, A549, and HepG2 C3A) individually on transwell membranes with high viability (above 97%) for 48 h under simulated shipping conditions without an incubator. The device was also tested by actual overnight shipping of blood brain barrier constructs consisting of human induced pluripotent brain microvascular endothelial cells and rat astrocytes on transwell membranes to a remote facility (approximately 1200 miles away). The blood brain barrier constructs arrived with high cell viability and were able to regain full barrier integrity after equilibrating in the incubator for 24 h; this was assessed by the presence of continuous tight junction networks and in vivo-like values for trans-endothelial electrical resistance (TEER). These results demonstrated that our cell transport device could be a useful tool for long-distance transport of membrane-bound cell cultures and functional tissue constructs. Studies that involve various cell and tissue constructs, such as the "Multi-Organ-on-Chip" devices (where multiple microscale tissue constructs are integrated on a single microfluidic device) and studies that involve microenvironments where multiple tissue interactions are of interest, would benefit from the ability to transport or receive these constructs. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1257-1266, 2017.

Development, qualification, validation and application of the neutral red uptake assay in Chinese Hamster Ovary (CHO) cells using a VITROCELL® VC10® smoke exposure system

Cytotoxicity assessment of combustible tobacco products by neutral red uptake (NRU) has historically used total particulate matter (TPM) or solvent captured gas vapor phase (GVP), rather than fresh whole smoke. Here, the development, validation and application of the NRU assay in Chinese Hamster Ovary (CHO) cells, following exposure to fresh whole smoke generated with the VITROCELL® VC10® system is described. Whole smoke exposure is particularly important as both particulate and vapor phases of tobacco smoke show cytotoxicity in vitro. The VITROCELL® VC10® system provides exposure at the air liquid interface (ALI) to mimic in vivo conditions for assessing the toxicological impact of smoke in vitro. Instrument and assay validations are crucial for comparative analyses.

GOALS OF THIS STUDY

1) demonstrate functionality of the VITROCELL® VC10® system by installation, operational and performance qualification, 2) develop and validate a cellular system for assessing cytotoxicity following whole smoke exposure and 3) assess the whole smoke NRU assay sensitivity for statistical differentiation between a reference combustible cigarette (3R4F) and a primarily "heat-not-burn" cigarette (Eclipse).

RESULTS

The VITROCELL® VC10® provided consistent generation and delivery of whole smoke; exposure-related changes in in vitro cytotoxicity were observed with reproducible IC50 values; comparative analysis showed that the heat-not-burn cigarette was significantly (P<0.001) less cytotoxic than the 3R4F combustible cigarette, consistent with the lower levels of chemical constituents liberated by primarily-heating the cigarette versus burning.

Cell and tissue-based in vitro models for improving the development of oral inhalation drug products

The interplay of costs and ethics has increased the need for adequate models mimicking the human in vivo situation drastically. An adequate model has the ability to generate data which are predictive for a certain aspect of the human response, for example for the bioavailability. This review highlights how in vitro models can enrich pulmonary drug delivery research with more detailed insights in cellular and non-cellular barriers, allowing for faster improvements and significant innovations of inhalation drug products. Risk assessment in inhalation toxicology and aerosol medicines and related important guidelines (e.g. OECD, EMA) are mentioned as a fundament for the described methods. Principle decisions to find a suitable in vitro tool for the question being asked are discussed to support the individual selection. Depending on the cellular and non-cellular barrier, exemplary in vitro tools are described with their ability to reflect a certain part of the in vivo lung situation. The review closes with a short summary of more complex systems as well as their advantages and limitations.

Evaluation of an in vitro screening model to assess phosgene inhalation injury

Therapeutic development against exposure to toxic gases is hindered by the lack of appropriate models to evaluate candidate compounds prior to animal efficacy studies. In this study, an in vitro, air-liquid interface exposure model has been tested to examine its potential application for screening treatments for phosgene (carbonyl chloride)-induced pulmonary injury. Epithelial cultures on Transwell^® inserts, combined with a Vitrocell^® exposure apparatus, provided a physiologically relevant exposure environment. Differentiated human bronchial epithelial (16HBE) cultures were exposed for 8 min to phosgene ranging from 0 to 64 ppm and assessed for changes in transepithelial electrical resistance (TEER, epithelial barrier integrity), cellular viability (XTT) and post-exposure (PE) cellular metabolic energy status. Exposure to phosgene concentrations ≥8 ppm caused dose-dependent and significant decreases in TEER and XTT which did not recover within 24-h PE. In addition, at 64 ppm the rate of oxidative glutamine metabolism was significantly inhibited at 6 and 24 h after exposure. Glycolytic activities (glucose utilization and lactate production) were also inhibited, but to a lesser extent. Decreased glycolytic function can translate to insufficient energy sources to counteract barrier function failure. Consistent and sensitive markers of phosgene exposure were TEER, cell viability and decreased metabolism. As such, we have assessed an appropriate in vitro model of phosgene inhalation that produced quantifiable alterations in markers of lung cell metabolism and injury in human airway epithelial cells. Data indicate the suitability of this model for testing classes of anti-edemagenic compounds such as corticosteroids or phosphodiesterase inhibitors for evaluating phosgene therapeutics.

Diesel exhaust: current knowledge of adverse effects and underlying cellular mechanisms

Diesel engine emissions are among the most prevalent anthropogenic pollutants worldwide, and with the growing popularity of diesel-fueled engines in the private transportation sector, they are becoming increasingly widespread in densely populated urban regions. However, a large number of toxicological studies clearly show that diesel engine emissions profoundly affect human health. Thus the interest in the molecular and cellular mechanisms underlying these effects is large, especially concerning the nature of the components of diesel exhaust responsible for the effects and how they could be eliminated from the exhaust. This review describes the fundamental properties of diesel exhaust as well as the human respiratory tract and concludes that adverse health effects of diesel exhaust not only emerge from its chemical composition, but also from the interplay between its physical properties, the physiological and cellular properties, and function of the human respiratory tract. Furthermore, the primary molecular and cellular mechanisms triggered by diesel exhaust exposure, as well as the fundamentals of the methods for toxicological testing of diesel exhaust toxicity, are described. The key aspects of adverse effects induced by diesel exhaust exposure described herein will be important for regulators to support or ban certain technologies or to legitimate incentives for the development of promising new technologies such as catalytic diesel particle filters.

In vitro cytotoxicity testing of airborne formaldehyde collected in serum-free culture media

The purpose of this study was to identify a suitable sampling model for on-site toxicity assessment of soluble air contaminants such as formaldehyde, a well known industrial and indoor air contaminant. The in vitro cytotoxicity of formaldehyde, the selected model for soluble air contaminants, was studied using the MTS (tetrazolium salt) assay in two carcinoma cell lines, A549 epithelial lung and HepG2 hepatocarcinoma, and in skin fibroblasts. The cytotoxic effects of airborne formaldehyde were evaluated using test atmospheres in concentrations below 10 ppm (12.3 mg/m3), generated by a dynamic diffusion method and bubbled (0.3 L/min) through serum-free culture media for one or four hours. Human cells were treated with formaldehyde air samples, and cell viability was determined after four hours incubation. In parallel, the concentration of airborne formaldehyde was monitored, using the 3500 NIOSH method. Cell viability of the HepG2 cells exposed to formaldehyde air samples (8.75 ppm-4 h) was reduced to less than 50% (31.69/1.24%). The HepG2 cell lines were found to be more sensitive (IC50=103.799/23.55 mg/L) to formaldehyde than both A549 cell lines (IC50=198.369/9.54 mg/L) and skin fibroblasts (IC50=196.689/36.73 mg/L) (PB/0.01). An average of 96.8% was determined for collection efficiency of formaldehyde in serum-free culture media. The results of this study suggest that absorption of soluble air contaminants, such as formaldehyde, in serum-free culture media can be used as a suitable sampling model for on-site toxicity assessments.

A model of human nasal epithelial cells adapted for direct and repeated exposure to airborne pollutants

Airway epithelium lining the nasal cavity plays a pivotal role in respiratory tract defense and protection mechanisms. Air pollution induces alterations linked to airway diseases such as asthma. Only very few in vitro studies to date have succeeded in reproducing physiological conditions relevant to cellular type and chronic atmospheric pollution exposure. We therefore, set up an in vitro model of human Airway Epithelial Cells of Nasal origin (hAECN) close to real human cell functionality, specifically adapted to study the biological effects of exposure to indoor gaseous pollution at the environmental level. hAECN were exposed under air-liquid interface, one, two, or three-times at 24 h intervals for 1 h, to air or formaldehyde (200 μg/m(3)), an indoor air gaseous pollutant. All experiments were ended at day 4, when both cellular viability and cytokine production were assessed. Optimal adherence and confluence of cells were obtained 96 h after cell seeding onto collagen IV-precoated insert. Direct and repeated exposure to formaldehyde did not produce any cellular damage or IL-6 production change, although weak lower IL-8 production was observed only after the third exposure. Our model is significantly better than previous ones due to cell type and the repeated exposure protocol.

Toxicological perspectives of inhaled therapeutics and nanoparticles

INTRODUCTION

The human respiratory system is an important route for the entry of inhaled therapeutics into the body to treat diseases. Inhaled materials may consist of gases, vapours, aerosols and particulates. In all cases, assessing the toxicological effect of inhaled therapeutics has many challenges.

AREAS COVERED

This article provides an overview of in vivo and in vitro models for testing the toxicity of inhaled therapeutics and nanoparticles implemented in drug delivery. Traditionally, inhalation toxicity has been performed on test animals to identify the median lethal concentration of airborne materials. Later maximum tolerable concentration denoted by LC0 has been introduced as a more ethically acceptable end point. More recently, in vitro methods have been developed, allowing the direct exposure of airborne material to cultured human target cells on permeable porous membranes at the air-liquid interface.

EXPERT OPINION

Modifications of current inhalation therapies, new pulmonary medications for respiratory diseases and implementation of the respiratory tract for systemic drug delivery are providing new challenges when conducting well-designed inhalation toxicology studies. In particular, the area of nanoparticles and nanocarriers is of critical toxicological concern. There is a need to develop toxicological test models, which characterise the toxic response and cellular interaction between inhaled particles and the respiratory system.

Urban particulate matter induces pro-remodeling factors by airway epithelial cells from healthy and asthmatic children

CONTEXT

Chronic exposure to ambient particulate matter pollution during childhood is associated with decreased lung function growth and increased prevalence of reported respiratory symptoms. The role of airway epithelium-derived factors has not been well determined.

OBJECTIVE

To determine if urban particulate matter (UPM) stimulates production of vascular endothelial growth factor (VEGF) and transforming growth factor-β2 (TGF-β2), and gene expression of mucin 5AC (MUC5AC) and interleukin-(IL)-8 by primary airway epithelial cells (AECs) obtained from carefully phenotyped healthy and atopic asthmatic school-aged children.

METHODS

Primary AECs from 9 healthy and 14 asthmatic children were differentiated in air--liquid interface (ALI) culture. The apical surface was exposed to UPM suspension or phosphate buffered saline (PBS) vehicle control for 96 h. VEGF and TGF-β2 concentrations in cell media at baseline, 48 and 96 h were measured via ELISA. MUC5AC and IL-8 expression by AECs at 96 h was measured via quantitative polymerase chain reaction.

RESULTS

Baseline concentrations of VEGF, but not TGF-β2, were significantly higher in asthmatic versus healthy cultures. UPM stimulated production of VEGF, but not TGF-β2, at 48 and 96 h; the magnitude of change was comparable across groups. At 96 h there was greater MUC5AC and IL-8 expression by UPM exposed compared to PBS exposed AECs.

CONCLUSIONS

Induction of the pro-remodeling cytokine VEGF may be a potential mechanism by which UPM influences lung function growth in children irrespective of asthma status. Respiratory morbidity associated with UPM exposure in children may be related to increased expression of MUC5AC and IL-8.

Airborne acrolein induces keratin-8 (Ser-73) hyperphosphorylation and intermediate filament ubiquitination in bronchiolar lung cell monolayers

The combustion product acrolein is a key mediator of pulmonary edema in victims of smoke inhalation injury. Since studying acrolein toxicity in conventional in vitro systems is complicated by reactivity with nucleophilic culture media constituents, we explored an exposure system which delivers airborne acrolein directly to lung cell monolayers at the air-liquid interface. Calu-3 lung adenocarcinoma cells were maintained on membrane inserts such that the basal surface was bathed in nucleophile-free media while the upper surface remained in contact with acrolein-containing air. Cells were exposed to airborne acrolein for 30 min before they were allowed to recover in fresh media, with cell sampling at defined time points to allow evaluation of toxicity and protein damage. After prior exposure to acrolein, cell ATP levels remained close to controls for 4h but decreased in an exposure-dependent manner by 24h. A loss of transepithelial electrical resistance and increased permeability to fluorescein isothiocyanate-labeled dextran preceded ATP loss. Use of antibody arrays to monitor protein expression in exposed monolayers identified strong upregulation of phospho-keratin-8 (Ser(73)) as an early consequence of acrolein exposure. These changes were accompanied by chemical damage to keratin-8 and other intermediate filament family members, while acrolein exposure also resulted in controlled ubiquitination of high mass proteins within the intermediate filament extracts. These findings confirm the usefulness of systems allowing delivery of airborne smoke constituents to lung cell monolayers during studies of the molecular basis for acute smoke intoxication injury.

Validation of the dynamic direct exposure method for toxicity testing of diesel exhaust in vitro

Diesel exhaust emission is a major health concern because of the complex nature of its gaseous content (e.g., NO₂, NO, CO, and CO₂) and high concentration of particulate matter (PM) less than 2.5 μm which allows for deeper penetration into the human pulmonary system upon inhalation. The aim of this research was to elucidate the potential toxic effects of diesel exhaust on a human pulmonary-based cellular system. Validation of a dynamic direct exposure method for both laboratory (230 hp Volvo truck engine) and field (Volkswagen Passat passenger car) diesel engines, at idle mode, was implemented. Human pulmonary type II epithelial cells (A549) grown on porous membranes were exposed to unmodified diesel exhaust at a low flow rate (37.5 mL/min). In parallel, diesel emission sampling was also conducted using real-time air monitoring techniques. Induced cellular effects were assessed using a range of in vitro cytotoxicity assays (MTS, ATP, and NRU). Reduction of cell viability was observed in a time-dependent manner following 30–60 mins of exposure with NRU as the most sensitive assay. The results suggest that the dynamic direct exposure method has the potential to be implemented for both laboratory- and field-based in vitro toxicity studies of diesel exhaust emissions.

An improved 3D tetraculture system mimicking the cellular organisation at the alveolar barrier to study the potential toxic effects of particles on the lung

Background

Exposure to fine and ultra-fine ambient particles is still a problem of concern in many industrialised parts of the world and the intensified use of nanotechnology may further increase exposure to small particles. Complex in vitro coculture systems may be valuable tools to study particle-induced processes and to extrapolate effects of particles on the lung. A system consisting of four different human cell lines which mimics the cell response of the alveolar surface in vitro was developed to study native aerosol exposure (Vitrocell™ chamber). The system is composed of an alveolar type-II cell line (A549), differentiated macrophage-like cells (THP-1), mast cells (HMC-1) and endothelial cells (EA.hy 926), seeded in a 3D-orientation on a microporous membrane.

Results

The spatial distribution of the cells in the tetraculture was analysed by confocal laser scanning microscopy (CLSM), showing a confluent layer of endothelial and epithelial cells on both sides of the transwell. Macrophage-like cells and mast cells can be found on top of the epithelial cells. The cells formed colonies under submerged conditions, which disappeared at the ALI. To evaluate the response to oxidative stress, the dichlorodihydrofluorescein diacetate (DCFH-DA) assay was used together with 2,2’-azobis-2-methyl-propanimidamide-dihydrochloride (AAPH) as inducer of oxidative stress. The tetraculture showed less induction of reactive oxygen species (ROS) production after being treated with a positive control compared to the monocultures of EA.hy 926, THP-1 and HMC-1. Submerged cultures showed elevated ROS and IL-8 levels compared to ALI cultures. The Vitrocell™ aerosol exposure system was not significantly influencing the viability. Using this system, cells were exposed to an aerosol of 50 nm SiO₂-Rhodamine NPs in PBS. The distribution of the NPs in the tetraculture after exposure was evaluated by CLSM. Fluorescence from internalized particles was detected in CD11b-positive THP-1 cells only.

Conclusion

The system can be used in conjunction with a native aerosol exposure system and may finally lead to a more realistic judgement regarding the hazard of new compounds and/or new nano-scaled materials in the future. The results for the ROS production and IL-8 secretion suggest that submerged exposure may lead to an overestimation of observed effects.

Morphological and functional differentiation in BE(2)-M17 human neuroblastoma cells by treatment with Trans-retinoic acid

Background

Immortalized neuronal cell lines can be induced to differentiate into more mature neurons by adding specific compounds or growth factors to the culture medium. This property makes neuronal cell lines attractive as in vitro cell models to study neuronal functions and neurotoxicity. The clonal human neuroblastoma BE(2)-M17 cell line is known to differentiate into a more prominent neuronal cell type by treatment with trans-retinoic acid. However, there is a lack of information on the morphological and functional aspects of these differentiated cells.

Results

We studied the effects of trans-retinoic acid treatment on (a) some differentiation marker proteins, (b) types of voltage-gated calcium (Ca²⁺) channels and (c) Ca²⁺-dependent neurotransmitter ([³H] glycine) release in cultured BE(2)-M17 cells. Cells treated with 10 μM trans-retinoic acid (RA) for 72 hrs exhibited marked changes in morphology to include neurite extensions; presence of P/Q, N and T-type voltage-gated Ca²⁺ channels; and expression of neuron specific enolase (NSE), synaptosomal-associated protein 25 (SNAP-25), nicotinic acetylcholine receptor α7 (nAChR-α7) and other neuronal markers. Moreover, retinoic acid treated cells had a significant increase in evoked Ca²⁺-dependent neurotransmitter release capacity. In toxicity studies of the toxic gas, phosgene (CG), that differentiation of M17 cells with RA was required to see the changes in intracellular free Ca²⁺ concentrations following exposure to CG.

Conclusion

Taken together, retinoic acid treated cells had improved morphological features as well as neuronal characteristics and functions; thus, these retinoic acid differentiated BE(2)-M17 cells may serve as a better neuronal model to study neurobiology and/or neurotoxicity.

Assessment of cigarette smoke particle deposition within the Vitrocell® exposure module using quartz crystal microbalances

BACKGROUND

Cigarette smoking is a cause of a variety of serious diseases, and to understand the toxicological impact of tobacco smoke in vitro, whole smoke exposure systems can be used. One of the main challenges of the different whole smoke exposure systems that are commercially available is that they dilute and deliver smoke in different ways, limiting/restricting the cross-comparison of biological responses. This is where dosimetry - dose quantification - can play a key role in data comparison. Quartz crystal microbalance (QCM) technology has been put forward as one such tool to quantify smoke particle deposition in vitro, in real-time.

RESULTS

Using four identical QCMs, installed into the Vitrocell® mammalian 6/4 CF Stainless exposure module, we were able to quantify deposited smoke particle deposition, generated and diluted by a Vitrocell® VC 10 Smoking Robot. At diluting airflows 0.5-4.0 L/min and vacuum flow rate 5 ml/min/well through the exposure module, mean particle deposition was in the range 8.65 ± 1.51 μg/cm(2)-0.72 ± 0.13 μg/cm(2). Additionally, the effect of varying vacuum flow rate on particle deposition was assessed from 5 ml/min/well - 100 ml/min/well. Mean deposited mass for all four airflows tested per vacuum decreased as vacuum rate was increased: mean deposition was 3.79, 2.75, 1.56 and 1.09 μg/cm(2) at vacuum rates of 5, 10, 50 and 100 ml/min/well respectively.

CONCLUSIONS

QCMs within the Vitrocell® exposure module have demonstrated applicability at defining particle dose ranges at various experimental conditions. This tool will prove useful for users of the Vitrocell® system for dose-response determination and QC purposes.

Detection of the cytotoxicity of water-insoluble fraction of cigarette smoke by direct exposure to cultured cells at an air-liquid interface

For the biological evaluation of cigarette smoke in vitro, the particulate phase (PP) and the gas vapor phase (GVP) of mainstream smoke have usually been collected individually and exposed to biological material such as cultured cells. Using this traditional method, the GVP is collected by bubbling in an aqueous solution such as phosphate-buffered saline (PBS). In such a way the water-insoluble GVP fraction is excluded from the GVP, meaning that the toxic potential of the water-insoluble GVP fraction has hardly been investigated so far. In our experiments we used a direct exposure method to expose cells at the air-liquid interface (ALI) to the water-insoluble GVP fraction for demonstrating its toxicological/biological activity. In order to isolate the water-insoluble GVP fraction from mainstream smoke, the GVP was passed through 6 impingers connected in series with PBS. After direct exposure of Chinese hamster ovary cells (CHO-K1) with the water-insoluble GVP fraction in the CULTEX(®) system its cytotoxicity was assayed by using the neutral red uptake assay. The water-insoluble GVP fraction was proven to be less cytotoxic than the water-soluble GVP fraction, but showed a significant effect in a dose-dependent manner. The results of this study showed that the direct exposure of cultivated cells at the air-liquid interface offers the possibility to analyze the biological and toxicological activities of all fractions of cigarette smoke including the water-insoluble GVP fraction.

An alternative gas-phase in vitro exposure system for toxicity testing: the interaction between nitrous oxide and A549 cells

An original in vitro approach was adopted to expose cells to volatile agents. The anaesthetic nitrous oxide (N(2)O) was chosen as the model agent, and type II pneumocyte-like cells (A549 cells) were used as the target to represent the lungs. A time-lapse microscopy station was equipped with a manual gas mixer that allowed the generation of a mixture of N(2)O/air/CO(2) in the gas phase, to provide a uniform distribution of the volatile agent. The dissolution of N(2)O in the culture medium was monitored by gas chromatography-electron capture detection. Biochemical alterations, in terms of homocysteine accumulation, demonstrated that intracellular methionine synthase had been inactivated by N(2)O absorbed by the cells, a process that also occurs in vivo. Toll-like receptors, which are key molecules in inflammatory lung diseases, were also investigated at the molecular level. Our experiments indicated that biochemical and molecular alterations occurred in the cells, even under conditions where neither morphologic changes nor consistent alterations in cell proliferation were evident. This in vitro exposure system can be efficiently adopted for looking at the repeat-dose effects of volatile agents on respiratory tissues. Moreover, it could be of further benefit for identifying the wide range of specific cell targets, and for monitoring relevant endpoints in the cellular and molecular processes that occur during exposure to volatile compounds.

Potential of coculture in vitro models to study inflammatory and sensitizing effects of particles on the lung

Exposure to particulate matter (PM) like nanoparticles (NPs) has increased in the last century due to increased combustion processes, road traffic, etc. In addition, the progress in chemical and cosmetic industry led to many new compounds, e.g. fragrances, which humans are exposed to every day. Many chemicals are known to act as contact and some as respiratory sensitizers, causing allergic reactions. Exposure to small particles of less than 100 nm in diameter is linked with an increased risk of respiratory diseases, such as asthma or rhinitis. To date already more than 1000 customer products contain eNPs without knowing much about the health effects. In comparison to chemicals, the mechanisms by which PM and eNPs can cause sensitization are still not fully understood. Validated and regulatory accepted in vitro models to assess this hazard in its full range are still missing. While a huge number of animal studies contributed to our knowledge about sensitization processes, knowledge on involved cellular mechanisms is still limited. In this review relevant in vitro models to study and elucidate these mechanisms in more detail are presented and their potential to serve as part of a tiered testing strategy is discussed.

Cellular response to the deposition of diesel exhaust particle aerosols onto human lung cells grown at the air-liquid interface by inertial impaction

The pathogenesis of disease resulting from exposure to diesel exhaust particles (DEP) is often studied using cultured lung cells. Frequently, researchers expose cells to DEP by spiking a suspension of particles in liquid onto the apical surface. This is not representative of in vivo exposure, where aerosols are deposited onto cell surfaces at the air-liquid interface (ALI). Inertial impaction provides an opportunity to deliver high doses of particles with aerodynamic diameters>∼1 μm to the surface of cells in seconds in a reproducible and predictable manner. A custom device was constructed to deposit DEP aerosols onto the surface of Calu-3 and A549 cells grown at the ALI. The pro-inflammatory and toxic cellular response to exposure to the deposited DEP aerosols was measured and compared to the response of cells exposed to DEP as suspensions. Calu-3 cells showed evidence of an oxidative stress response for both exposure types, while there was strong evidence to suggest that the method of aerosol delivery was harmful to the A549 cells.

Development of an in vitro exposure model for investigating the biological effects of therapeutic aerosols on human cells from the respiratory tract

Respiratory diseases like asthma or COPD are gaining more and more importance worldwide due to an increased exposure of humans to inhalable compounds such as cigarette smoke, diesel exhaust or other forms of environmental pollution. Therefore, a high impact on national health systems is expected, meaning long-term treatment, with periodic examinations accompanied by high costs. Although a number of efficient drugs for these disease patterns, like Tiotropium (antimuscarinic), Salmetron (β-antagonist) or corticosteroids, are already available, a great deal of effort has to be put into the development of new drugs and therapy concepts. In this context, in vitro methods may be useful to establish more efficient prescreening procedures to analyze, for example, the toxicity of new compounds during the research and development process. These studies should aim to achieve a better selection of substances relevant for further development and a final reduction in the number of animal experiments. Therefore, we established an in vitro exposure device that allows the analysis of inhalable compounds for their pharmacological and toxicological effects. This CULTEX(®) device is composed of an exposure entity representing the in vivo respiratory air compartment and a basal feeding compartment representing the subepithelium. Both compartments are connected by porous transwells on which cells form an epithelium-like cell layer. We have used this system for exposing human lung cells directly to liquid aerosols and present the first data with regard to aerosolized model substances.

Role of MAP kinases in regulating expression of antioxidants and inflammatory mediators in mouse keratinocytes following exposure to the half mustard, 2-chloroethyl ethyl sulfide

Dermal exposure to sulfur mustard causes inflammation and tissue injury. This is associated with changes in expression of antioxidants and eicosanoids which contribute to oxidative stress and toxicity. In the present studies we analyzed mechanisms regulating expression of these mediators using an in vitro skin construct model in which mouse keratinocytes were grown at an air-liquid interface and exposed directly to 2-chloroethyl ethyl sulfide (CEES), a model sulfur mustard vesicant. CEES (100-1000 microM) was found to cause marked increases in keratinocyte protein carbonyls, a marker of oxidative stress. This was correlated with increases in expression of Cu,Zn superoxide dismutase, catalase, thioredoxin reductase and the glutathione S-transferases, GSTA1-2, GSTP1 and mGST2. CEES also upregulated several enzymes important in the synthesis of prostaglandins and leukotrienes including cyclooxygenase-2 (COX-2), microsomal prostaglandin E synthase-2 (mPGES-2), prostaglandin D synthase (PGDS), 5-lipoxygenase (5-LOX), leukotriene A(4) (LTA(4)) hydrolase and leukotriene C(4) (LTC(4)) synthase. CEES readily activated keratinocyte JNK and p38 MAP kinases, signaling pathways which are known to regulate expression of antioxidants, as well as prostaglandin and leukotriene synthases. Inhibition of p38 MAP kinase suppressed CEES-induced expression of GSTA1-2, COX-2, mPGES-2, PGDS, 5-LOX, LTA(4) hydrolase and LTC(4) synthase, while JNK inhibition blocked PGDS and GSTP1. These data indicate that CEES modulates expression of antioxidants and enzymes producing inflammatory mediators by distinct mechanisms. Increases in antioxidants may be an adaptive process to limit tissue damage. Inhibiting the capacity of keratinocytes to generate eicosanoids may be important in limiting inflammation and protecting the skin from vesicant-induced oxidative stress and injury.

An effort to test the embryotoxicity of benzene, toluene, xylene, and formaldehyde to murine embryonic stem cells using airborne exposure technique

Benzene, toluene, xylene, and formaldehyde are well-known indoor air pollutants, especially after house decoration. They are also common pollutants in the working places of the plastic industry, chemical industry, and leather industry. It has been reported that these pollutants cause people to be irritated, sick, experience a headache, and be dizzy. They also have the potential to induce asthma, aplastic anemia, and leukemia, even cause abortion or fetus malformation in humans. In this study, the airborne toxicity of benzene, toluene, xylene, and formaldehyde to murine embryonic stem cells (mES cells) were tested using airborne exposure technique to evaluate the mES cell airborne exposure model on embryotoxicity prediction. Briefly, mES cells were cultured on Transwell inserts and were exposed to an airborne surrounding of test chemicals in a chamber for 1 h at 37 degrees C. Cytotoxicity was determined using the MTT assay after further culture for 18 h at 37 degrees C in normal medium. The airborne IC(50) (50% inhibition concentration) of benzene, toluene, xylene, and formaldehyde derived from the fitted dose-response curves were 17,400 +/- 1290, 16,000 +/- 250, 4680 +/- 500, and 620 +/- 310 ppm, respectively. Formaldehyde was found to be the compound most toxic to mES cells compared to benzene homologues. The toxicity data had good correlation with the in vivo data. The results showed that the mES airborne exposure model may be used to predict embryotoxicity of volatile organic compounds.

Characterization of a whole smoke in vitro exposure system (Burghart Mimic Smoker-01)

In vitro systems are frequently used to study mechanisms of mainstream cigarette smoke (MS)-induced lung injury. Traditional methods of exposure involve the capture of MS particulate phase with filter pads or bubbling MS through phosphate buffered saline (PBS) or cell culture medium. Although useful for in vitro experiments, these exposure methods may fail to capture potential interactions between the gas and particulate phases. To better understand the effect of MS on the human airway, in vitro whole smoke exposure systems that utilize freshly generated whole smoke are needed. Here we report the characterization of a new in vitro whole smoke exposure system (Burghart Mimic Smoker-01 (MSB-01)). This system uses a smoke distribution manifold to simultaneously deliver MS to each well of a 96-well plate. Intraday and interday variations for particulate matter deposition were less than 5% and 13% respectively. Cytotoxicity measurements using lung epithelial BEAS-2B cells indicate variations in calculated EC(50) (half maximal effective concentration) values of 13% intraday and 20% interday. Smoke particulate losses and changes in particle size distribution were also analyzed. The data indicate that 45-50% of the MS generated at the smoking ports is lost within the system prior to delivery into the exposure chamber; however, no changes in particle size distribution were detected throughout the system. Overall, the MSB-01 reproducibly delivered mainstream cigarette smoke in a dose dependent manner across the multiwell plate. The MSB-01 is a high throughput system capable of exposing cells to both the MS particulate and gas/vapor phases simultaneously.

Inhalation toxicity studies: OECD guidelines in relation to REACH and scientific developments

The OECD Health Effects Test Guidelines (TGs) provide guidance concerning the use of methods for the identification and characterization of hazards from chemical substances. These TGs are largely based on tests in routine use for many years and are known to yield information relevant to various types of toxicity. They have proven their value in practice and will remain of paramount importance for decades to come. However, the TGs describe mostly animal assays, and there is an increasingly strong urge to reduce animal testing on ethical grounds. In addition, assessment procedures are generally considered too slow and too rigid, which has resulted in elaborate testing of a relatively small number of chemicals, while virtually nothing is known about the vast majority of compounds. The major objectives of Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) are to improve the knowledge about the properties and use of chemicals and to speed up the procedure of risk assessment. The REACH text contains information requirements that can be met by OECD TGs but REACH also provides rules for adaptation of the standard testing regime. Also, various components of "Intelligent Testing Strategies" are described in order to limit animal testing. This paper briefly describes the OECD TGs for inhalation toxicity studies, including those in preparation, and their role in future hazard identification. This will be discussed in relation to the evaluation of the safety of thousands of chemicals in a relatively short period of time and scientific developments, including the use of alternatives to animal testing.

The generation of diesel exhaust particle aerosols from a bulk source in an aerodynamic size range similar to atmospheric particles

The influence of diesel exhaust particles (DEP) on the lungs and heart is currently a topic of great interest in inhalation toxicology. Epidemiological data and animal studies have implicated airborne particulate matter and DEP in increased morbidity and mortality due to a number of cardiopulmonary diseases including asthma, chronic obstructive pulmonary disorder, and lung cancer. The pathogeneses of these diseases are being studied using animal models and cell culture techniques. Real-time exposures to freshly combusted diesel fuel are complex and require significant infrastructure including engine operations, dilution air, and monitoring and control of gases. A method of generating DEP aerosols from a bulk source in an aerodynamic size range similar to atmospheric DEP would be a desirable and useful alternative. Metered dose inhaler technology was adopted to generate aerosols from suspensions of DEP in the propellant hydrofluoroalkane 134a. Inertial impaction data indicated that the particle size distributions of the generated aerosols were trimodal, with count median aerodynamic diameters less than 100 nm. Scanning electron microscopy of deposited particles showed tightly aggregated particles, as would be expected from an evaporative process. Chemical analysis indicated that there were no major changes in the mass proportion of 2 specific aromatic hydrocarbons (benzo[a]pyrene and benzo[k]fluoranthene) in the particles resulting from the aerosolization process.

Comparative in vitro cytotoxicity assessment of selected gaseous compounds in human alveolar epithelial cells

Exposure to airborne contaminants is significantly associated with human health risks, ranging from bronchial reactivity to morbidity and mortality due to acute intense or long term low level repeated exposures. However, the precise mechanisms that derive such effects are not always understood. Although inhalation studies are technologically complicated, correct hazard characterisation is essential for comparable risk assessment of inhaled materials. The aim of this study was to investigate the comparative in vitro cytotoxicity of selected gaseous contaminants in human lung cells. The cytotoxicity of nitrogen dioxide (NO(2)), sulphur dioxide (SO(2)) and ammonia (NH(3)) was investigated in A549- human pulmonary type II-like epithelial cell lines cultured on porous membranes in Snapwell inserts. A dynamic direct exposure method was established by utilizing the horizontal diffusion chamber system (Harvard Apparatus Inc, USA) for delivery of test atmospheres. Test atmospheres were generated using a dynamic direct dilution method and the concentration monitored by appropriate analytical methods. A diversified battery of in vitro assays including the MTS (tetrazolium salt; Promega), NRU (neutral red uptake; Sigma) and ATP (adenosine triphosphate; Promega) assays was implemented. Airborne IC(50) (50% inhibitory concentration) values were calculated based on the most sensitive assay for each test gas including NO(2) (IC(50)=11+/-3.54 ppm; NRU)>SO(2) (IC(50)=48+/-2.83 ppm; ATP)> and NH(3) (IC(50)=199+/-1.41 ppm; MTS). However, all in vitro assays revealed similar toxicity ranking for selected gaseous contaminants. Identical toxicity ranking was achieved using both in vitro and published in vivo data. This comparison suggests that results of in vitro methods are comparable to in vivo data and may provide greater sensitivity for respiratory toxicity studies of gaseous contaminants.

An experimental in vitro model for dynamic direct exposure of human cells to airborne contaminants

The aim of this study was to establish a dynamic in vitro model for direct exposure of human cells to gaseous contaminants to investigate the cellular responses to airborne chemical exposures. Nitrogen dioxide (NO2) was selected as a model gas compound. Standard test atmospheres were generated (2.5-10 ppm), using a dynamic direct dilution method. Human cells including: A549 pulmonary type II-like epithelial cell lines and skin fibroblasts were grown on porous membranes. Human cells on snapwell inserts were placed in horizontal diffusion chambers and exposed to various airborne concentrations of NO2 directly at the air/liquid interface for 1 h at 37 degrees C. Cytotoxicity of the test gas was investigated using the MTS (3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium), NRU (neutral red uptake) and ATP (Adenosine triphosphate) assays. Dose-dependent effects of NO2 were observed in human cells tested which resulted in a significant reduction of cell viability at concentrations normally encountered in workplace environments (p<0.05). Our findings suggest that the dynamic direct exposure method can be used for in vitro inhalational and dermal toxicity studies and potentially as an advanced technology for biomonitoring of airborne contaminants in future occupational and environmental toxicity assessments.

Comparative assessment of three in vitro exposure methods for combustion toxicity

A comparative assessment of three approaches for the use of human cells in vitro to investigate combustion toxicity was conducted. These included one indirect and two direct (passive and dynamic) exposure methods. The indirect method used an impinger system in which culture medium was used to trap the toxicants, whilst the direct exposure involved the use of a Horizontal Harvard Navicyte Chamber at the air/liquid interface. The cytotoxic effects of thermal decomposition products were assessed using the MTS (3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium) assay (Promega) on a selection of human cells including: HepG2, A549 and skin fibroblasts. A small scale laboratory fire test using a vertical tube furnace was designed for the generation of combustion products. Polymethyl methacrylate (PMMA) was selected as a model polymer to study the cytotoxic effects of combustion products. NOAEC (no observable adverse effect concentration), IC10 (10% inhibitory concentration), IC50 (50% inhibitory concentration) and TLC (total lethal concentration) values were determined from dose response curves. Assessment using the NRU (neutral red uptake) and ATP (adenosine triphosphate) assays on human lung derived cells (A549) was also undertaken. Comparison between in vitro cytotoxicity results against published toxicity data for PMMA combustion and predicted LC50 (50% lethal concentration) values calculated from identified compounds using GCMS (gas chromatography mass spectrometry) was determined. The results suggested that the indirect exposure method did not appear to simulate closely exposure via inhalation, whilst exposure at the air/liquid interface by using the dynamic method proved to be a more representative method of human inhalation. This exposure method may be a potential system for in vitro cytotoxicity testing in combustion toxicity.

A novel in vitro exposure technique for toxicity testing of selected volatile organic compounds

Exposure to vapours of volatile chemicals is a major occupational and environmental health concern. Toxicity testing of volatile organic compounds (VOCs) has always faced significant technological problems due to their high volatility and/or low solubility. The aim of this study was to develop a practical and reproducible in vitro exposure technique for toxicity testing of VOCs. Standard test atmospheres of xylene and toluene were generated in glass chambers using a static method. Human cells including: A549-lung derived cell lines, HepG2-liver derived cell lines and skin fibroblasts, were grown in porous membranes and exposed to various airborne concentrations of selected VOCs directly at the air/liquid interface for 1 h at 37 degrees C. Cytotoxicity of test chemicals was investigated using the MTS (3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium) and NRU (neutral red uptake) assays following 24 h incubation. Airborne IC(50) (50% inhibitory concentration) values were determined using dose response curves for xylene (IC(50)=5350+/- 328 ppm, NRU; IC(50)=5750+/- 433 ppm, MTS in skin fibroblast) and toluene (IC(50)=0 500+/- 527 ppm, NRU; IC(50)=11,200 +/- 1,044 ppm, MTS in skin fibroblast). Our findings suggest that static direct exposure at the air/liquid interface is a practical and reproducible technique for toxicity testing of VOCs. Further, this technique can be used for inhalational and dermal toxicity studies of volatile chemicals in vitro as the exposure pattern in vivo is closely simulated by this method.

Oxidative stress induction by short time exposure to ozone on THP-1 cells

Ozone is a major component of air pollution mainly formed by photochemical reactions of nitrogen oxides with volatile organic compounds and/or carbon monoxide. Numerous studies have shown the association between ozone exposure with pulmonary injuries. This pollutant is a strong oxidant exerting its biological action either by direct reaction with target molecules or by generating reactive oxygen species which result in its biological effects and its toxicity. In order to study the effects of an induced oxidative stress by ozone on THP-1 cell, a human macrophage-like cell line, we used an in vitro system which has been previously used to study the rapid responses to ozone exposure. Using this system, THP-1 cells were subjected to short time exposure (30 min) followed by different incubation times ranging from 4 to 24 h. Our results show that ozone exposure provokes an alteration of the cell membrane translating an induction of lipid peroxidation resulting in a 3.2-fold increase of thiobarbituric reactive substances (TBARS), an increase by 35% of heme oxygenase-1 (HO-1) expression, and significant modifications of the redox status evaluated by glutathione measurement and of antioxidant enzyme activities in THP-1 cells. Our in vitro model constitutes a very interesting tool for the measurement of ozone effect on rapid modifications induced by this pollutant as well as intracellular modifications due to an oxidative stress.

Direct exposure methods for testing native atmospheres

In vitro studies of adverse cellular effects induced by inhalable substances face a number of problems due to the difficulties in exposing cultured cells of the respiratory tract directly to test atmospheres composed of complex gases and particulate compounds. This paper discusses the characteristics of in vitro work and summarizes the use of different in vitro technologies to determine the adverse effects of inhaled pollutants. The exposure of cells to test atmospheres requires accurate control of the pollutant levels, as well as the close contact of cells and gas without interfering with the medium. Systems which rely on the solution of the gas in the medium overlay do not resemble the exposure conditions in vivo, and may not be suitable for studying, for example, the effects of poorly soluble gases. Exposure to gases or complex mixtures can be performed with roller bottles or flasks on rotating and rocking platforms and, using these techniques, the cells are periodically exposed to the test atmosphere. However, the most promising approach is based on a biphasic cell culture technique, where cells are grown on microporous membranes at an air-liquid interface. Here the cells are nutrified from the basal side of the membrane whilst the apical part with the cultivated cells is in direct contact with the test atmosphere. Based on this culture technique, different exposure systems have been developed and these are described and discussed. Exposure of cells from the respiratory tract to gases or particles is responsible for cell injury or cell activation associated with an overexpression of mRNA and the release of bioactive mediators. Therefore, in vitro studies using such a strategy, in combination with relevant and efficient exposure devices, open up new ways to test native complex gases and aerosols. Furthermore, such an experimental approach is not only suitable for cultivated cells, but it can also be used for exposing bacteria to inhalable test compounds. It is possible to analyze the mutagenic potency of in- and outdoor pollutants and several attempts have been made to determine the induction of revertants in a modified Ames assay after exposure to single gases or complex mixtures.

A modified CULTEX system for the direct exposure of bacteria to inhalable substances

Increasing attention is being paid to the impact on human health of inhaled gaseous compounds and complex mixtures such as cigarette smoke. The evaluation of the genotoxicity of such materials is mostly based on experiments with model substances or mixtures and condensates in the standard Ames assay. Due to the methodological difficulties of testing air contaminants in their natural gaseous or aerosolised state, there are no generally accepted concepts and techniques for effective exposure of bacteria under such conditions. Therefore, we established a novel experimental approach using an exposure device based on the cell exposure system CULTEX. This allows us to investigate chemically and physically unchanged atmospheres like mainstream cigarette smoke by exposing bacteria of Salmonella typhimurium strains directly on the surface of culture media. The CULTEX exposure device can be connected to gas or aerosol generating systems. The introduction of this exposure device in the field of inhalation genotoxicology offers new test strategies for the in vitro evaluation of a wide range of inhalable substances in both laboratory and ambient situations. A patent was applied for this technical solution.

Comparative assessment of toxicities of mainstream smoke from commercial cigarettes

Three cigarette types were compared using an experimental approach for quantifying selected toxicological effects of diluted fresh whole cigarette mainstream smoke in vitro. The test procedure involved automatic smoking of cigarettes according to the FTC/ISO standard, online monitoring of generated smoke aerosols with respect to particulate and gas-phase components, and direct exposure of a human type II-like lung cell line (A549) using exposure conditions relevant to human smoking. Test specimens were the K1R4F standard research cigarettes (9.2 mg tar/cigarette) and two commercial European light filter cigarettes (brand 1, brand 2) having the same tar content (7.0 mg/cigarette). As a representative of the toxicological effect of smoke, intracellular reduced glutathione was analyzed directly after exposure of cells. Results revealed statistically significant different quantitative effects with regard to glutathione depletion when comparing whole smoke and filtered smoke from all three cigarettes. ED50 values revealed a depletion of reduced glutathione by brand 1 cigarettes that was more than twice the depletion caused by brand 2 cigarettes on a per cigarette basis. Also, quantitatively different effects were found on a per particle and on a per CO concentration basis using whole or filtered smoke from the cigarettes. We conclude that the methods we employed provide sensitive and reproducible ways of detecting differences in the toxicological action of smoke from various types of cigarettes.