Gentamicin coating of metallic implants reduces implant-related osteomyelitis in rats

Preparation of a novel antibacterial magnesium carbonate coating on a titanium surface and its in vitro biocompatibility

Magnesium-based coatings have attracted great attention in surface modification of titanium implants due to their superior angiogenic and osteogenic properties. However, their biological effects as a carbonate-based constituent remain unrevealed. In this study, magnesium carbonate coatings were prepared on titanium surfaces under hydrothermal conditions and subsequently treated with hydrogen peroxide. Also, their antibacterial activity and in vitro cell biocompatibility were evaluated. The obtained coatings consisted of nanoparticles without cracks and exhibited excellent adhesion to the substrate. X-ray diffraction (XRD) results indicated pure magnesium carbonate coatings formed on the Ti surface after hydrothermal treatment. After hydrogen peroxide treatment, the phase composition of the coatings had no obvious change. Compared to the untreated coatings, the hydrogen peroxide-treated coatings showed increased surface roughness and hydrophilicity. Co-culture with Staphylococcus aureus (S. aureus) demonstrated that the obtained coatings had good antibacterial activity. In vitro cell culture results showed that the hydrogen peroxide-treated coatings enhanced the viability, proliferation, and osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs). These findings suggest that this MgCO3-based coating exhibits excellent antibacterial performance and osteogenic potential. Based on the above, this study provides a simple method for preparing titanium implants with dual antibacterial and osteogenic capabilities, holding great promise in clinical applications.

Fracture-Related Infection-Epidemiology, Etiology, Diagnosis, Prevention, and Treatment

BACKGROUND

Fracture-related infection (FRI) is a challenge to physicians and other workers in health care. In 2018, there were 7253 listed cases of FRI in Germany, corresponding to an incidence of 10.7 cases per 100 000 persons per year.

METHODS

This review is based on pertinent publications retrieved from a search in PubMed with the search terms "fracture," "infection," "guideline," and "consensus." Aside from the primary literature, international guidelines and consensus recommendations were evaluated as well.

RESULTS

FRI arise mainly from bacterial contamination of the fracture site. Staphylococcus aureus is the most commonly detected pathogen. The treatment is based on surgery and antibiotics and should be agreed upon by an interdisciplinary team; it is often difficult because of biofilm formation. Treatment options include implant-preserving procedures and single-stage, two-stage, or multi-stage implant replacement. Treatment failure occurs in 10.3% to 21.4% of cases. The available evidence on the efficacy of various treatment approaches is derived mainly from retrospective cohort studies (level III evidence). Therefore, periprosthetic joint infections and FRI are often discussed together.

CONCLUSION

FRI presents an increasing challenge. Preventive measures should be optimized, and the treatment should always be decided upon by an interdisciplinary team. Only low-level evidence is available to date to guide diagnostic and treatment decisions. High-quality studies are therefore needed to help us meet this challenge more effectively.

Anti-Staphylococcal Activity of Ligilactobacillus animalis SWLA-1 and Its Supernatant against Multidrug-Resistant Staphylococcus pseudintermedius in Novel Rat Model of Acute Osteomyelitis

Osteomyelitis caused by staphylococcal infection is a serious complication of orthopedic surgery. Staphylococcus pseudintermedius is the main causative agent of osteomyelitis in veterinary medicine. Methicillin-resistant S. pseudintermedius (MRSP) has been reported in companion animals, especially dogs. Multidrug-resistant S. pseudintermedius is an emerging pathogen and has acquired antibiotic resistance against various commercial antimicrobial agents. New antimicrobial compounds are urgently needed to address antibiotic resistance, and the development of novel agents has become an international research hotspot in recent decades. Antimicrobial compounds derived from probiotics, such as bacteriocins, are promising alternatives to classical antibiotics. In this study, the antibacterial activities of Ligilactobacillus animalis SWLA-1 and its concentrated cell-free supernatant (CCFS) were evaluated in vitro and in vivo. The CCFS of this bacterium showed no toxicity against osteoblast and myoblast cells in vitro, while significantly inhibiting the multidrug-resistant S. pseudintermedius KUVM1701GC strain in a newly established rat model. The CCFS significantly inhibited multidrug-resistant staphylococci both in vitro and in vivo. This suggests that CCFS derived from L. animalis SWLA-1 has potential as an alternative to classic antibiotics for staphylococcal infections in dogs.

Highly Adhesive Antimicrobial Coatings for External Fixation Devices

Pin site infections arise from the use of percutaneous pinning techniques (as seen in skeletal traction, percutaneous fracture pinning, and external fixation for fracture stabilization or complex deformity reconstruction). These sites are niduses for infection because the skin barrier is disrupted, allowing for bacteria to enter a previously privileged area. After external fixation, the rate of pin site infections can reach up to 100%. Following pin site infection, the pin may loosen, causing increased pain (increasing narcotic usage) and decreasing the fixation of the fracture or deformity correction construct. More serious complications include osteomyelitis and deep tissue infections. Due to the morbidity and costs associated with its sequelae, strategies to reduce pin site infections are vital. Current strategies for preventing implant-associated infections include coatings with antibiotics, antimicrobial polymers and peptides, silver, and other antiseptics like chlorhexidine and silver-sulfadiazine. Problems facing the development of antimicrobial coatings on orthopedic implants and, specifically, on pins known as Kirschner wires (or K-wires) include poor adhesion of the drug-eluting layer, which is easily removed by shear forces during the implantation. Development of highly adhesive drug-eluting coatings could therefore lead to improved antimicrobial efficacy of these devices and ultimately reduce the burden of pin site infections. In response to this need, we developed two types of gel coatings: synthetic poly-glycidyl methacrylate-based and natural-chitosan-based. Upon drying, these gel coatings showed strong adhesion to pins and remained undamaged after the application of strong shear forces. We also demonstrated that antibiotics can be incorporated into these gels, and a K-wire with such a coating retained antimicrobial efficacy after drilling into and removal from a bone. Such a coating could be invaluable for K-wires and other orthopedic implants that experience strong shear forces during their implantation.

Zinc (Zn) Doping by Hydrothermal and Alkaline Heat-Treatment Methods on Titania Nanotube Arrays for Enhanced Antibacterial Activity

Titanium (Ti) is a popular biomaterial for orthopedic implant applications due to its superior mechanical properties such as corrosion resistance and low modulus of elasticity. However, around 10% of these implants fail annually due to bacterial infection and poor osseointegration, resulting in severe pain and suffering for the patients. To improve their performance, nanoscale surface modification approaches and doping of trace elements on the surfaces can be utilized which may help in improving cell adhesion for better osseointegration while reducing bacterial infection. In this work, at first, titania (TiO₂) nanotube arrays (NT) were fabricated on commercially available pure Ti surfaces via anodization. Then zinc (Zn) doping was conducted following two distinct methods: hydrothermal and alkaline heat treatment. Scanning electron microscopic (SEM) images of the prepared surfaces revealed unique surface morphologies, while energy dispersive X-ray spectroscopy (EDS) revealed Zn distribution on the surfaces. Contact angle measurements indicated that NT surfaces were superhydrophilic. X-ray photoelectron spectroscopy (XPS) provided the relative amount of Zn on the surfaces and indicated that hydrothermally treated surfaces had more Zn compared to the alkaline heat-treated surfaces. X-ray crystallography (XRD) and nanoindentation techniques provided the crystal structure and mechanical properties of the surfaces. While testing with adipose-derived stem cells (ADSC), the surfaces showed no apparent cytotoxicity to the cells. Finally, bacteria adhesion and morphology were evaluated on the surfaces after 6 h and 24 h of incubation. From the results, it was confirmed that NT surfaces doped with Zn drastically reduced bacteria adhesion compared to the Ti control. Zn-doped NT surfaces thus offer a potential platform for orthopedic implant application.

Recent Advancements in Metallic Drug-Eluting Implants

Over the past decade, metallic drug-eluting implants have gained significance in orthopedic and dental applications for controlled drug release, specifically for preventing infection associated with implants. Recent studies showed that metallic implants loaded with drugs were substituted for conventional bare metal implants to achieve sustained and controlled drug release, resulting in a desired local therapeutic concentration. A number of secondary features can be provided by the incorporated active molecules, including the promotion of osteoconduction and angiogenesis, the inhibition of bacterial invasion, and the modulation of host body reaction. This paper reviews recent trends in the development of the metallic drug-eluting implants with various drug delivery systems in the past three years. There are various types of drug-eluting implants that have been developed to meet this purpose, depending on the drug or agents that have been loaded on them. These include anti-inflammatory drugs, antibiotics agents, growth factors, and anti-resorptive drugs.

Meropenem-loaded Cement Is Effective in Preventing Gram-negative Osteomyelitis in an Animal Model

BACKGROUND

Low-dose antibiotic-loaded acrylic cement is routinely used for preventing skeletal infection or reimplantation in patients with periprosthetic joint infections. However, few reports about the selection of antibiotics in acrylic cement for antigram-negative bacteria have been proposed.

QUESTIONS/PURPOSES

(1) Does the addition of antibiotics (tobramycin, meropenem, piperacillin, ceftazidime, ciprofloxacin, and aztreonam) to acrylic cement adversely affect compressive strength before and after elution? (2) Which antibiotics have the highest cumulative release within 28 days? (3) Which antibiotics showed antimicrobial activity within 28 days? (4) Does meropenem-loaded cement improve body weight, temperature, and other inflammatory markers compared with control unloaded cement?

METHODS

This is an in vitro study that assessed the mechanical strength, antibiotic elution, and antibacterial properties of antibiotic-loaded cement, combined with an animal study in a rat model that evaluated key endpoints from the animal study. In the in vitro study, we added 2 g of tobramycin (TOB), meropenem (MEM), piperacillin (PIP), ceftazidime (CAZ), ciprofloxacin (CIP), and aztreonam (ATM) to 40 g of acrylic cement. The compressive strength, elution, and in vitro antibacterial properties of the antibiotic-loaded cement were detected. Thirty male rats were randomly divided into two groups: CON (antibiotic-unloaded cement) and MEM (meropenem-loaded cement, which had the most stable antibacterial properties of the six tested antibiotic-loaded cements in vitro within 28 days). The right tibia of all rats underwent arthroplasty and was implanted with the cement, followed by inoculation with Pseudomonas aeruginosa in the knee. General status, serum biomarkers, radiology, microbiological assay, and histopathological tests were assessed over 14 days postoperatively.

RESULTS

The compressive strength of all tested antibiotic cement combinations exceeded the 70 MPa threshold (the requirement established in ISO 5833). The cumulative release proportions of the raw antibiotic in cement were 1182.8 ± 37.9 µg (TOB), 355.6 ± 16.2 µg (MEM), 721.2 ± 40.3 µg (PIP), 477.4 ± 37.1 µg (CAZ), 146.5 ± 11.3 µg (CIP), and 372.1 ± 14.5 µg (ATM) within 28 days. Over a 28-day period, meropenem cement demonstrated antimicrobial activities against the four tested gram-negative bacteria ( Escherichia coli , P. aeruginosa , Klebsiella pneumoniae , and Proteus vulgaris ). Ciprofloxacin cement inhibited E. coli growth, ceftazidime and aztreonam cement inhibited K. pneumonia growth, and tobramycin cement inhibited P. aeruginosa . Only meropenem demonstrated antimicrobial activity against all gram-negative bacteria on agar diffusion bioassay. Rats treated with meropenem cement showed improved body weight (control: 280.1 ± 4.2 g, MEM: 288.5 ± 6.6 g, mean difference 8.4 [95% CI 4.3 to 12.6]; p < 0.001), improved knee width (control: 13.5 ± 0.3 mm, MEM: 11.8± 0.4 mm, mean difference 1.7 [95% CI 1.4 to 2.0]; p < 0.001), decreased inflammatory marker (control: 316.7 ± 45.0 mm, MEM: 116.5 ± 21.8 mm, mean difference 200.2 [95% CI 162.3 to 238.2]; p < 0.001), decreased radiographic scores (control: 17.7 ± 2.0 mm, MEM: 10.7± 1.3 mm, mean difference 7.0 [95% CI 5.4 to 8.6]; p < 0.001), improved bone volume/total volume (control: 8.7 ± 3.0 mm, MEM: 28.5 ± 5 .5 mm, mean difference 19.8 [95% CI 13.3 to 26.2]; p < 0.001), decreased Rissing scale scores of the knee gross pathology (control: 3.3 ± 0.5, MEM: 1.1 ± 0.7, mean difference 2.2 [95% CI 1.7 to 2.7]; p < 0.001), decreased Petty scale scores of knee synovium (control: 2.9 ± 0.4 mm, MEM: 0.7 ± 0.7 mm, mean difference 2.1 [95% CI 1.7 to 2.5]; p < 0.001), and decreased bacterial counts of the bone and soft tissues and negative bacterial cultures of cement (p < 0.001, p < 0.001, p < 0.001, p < 0.001, respectively).

CONCLUSION

In this current study, MEM cement had the most stable in vitro antimicrobial activities, effective in vivo activity while having acceptable mechanical and elution characteristics, and it may be an effective prophylaxis against skeletal infection caused by gram-negative bacteria.

CLINICAL RELEVANCE

Meropenem-loaded acrylic cement is a potentially effective prevention measure for skeletal infection caused by gram-negative bacteria; however, more related clinical research is needed to further evaluate the safety and efficacy.

Strategies to Mitigate and Treat Orthopaedic Device-Associated Infections

Orthopaedic device implants play a crucial role in restoring functionality to patients suffering from debilitating musculoskeletal diseases or to those who have experienced traumatic injury. However, the surgical implantation of these devices carries a risk of infection, which represents a significant burden for patients and healthcare providers. This review delineates the pathogenesis of orthopaedic implant infections and the challenges that arise due to biofilm formation and the implications for treatment. It focuses on research advancements in the development of next-generation orthopaedic medical devices to mitigate against implant-related infections. Key considerations impacting the development of devices, which must often perform multiple biological and mechanical roles, are delineated. We review technologies designed to exert spatial and temporal control over antimicrobial presentation and the use of antimicrobial surfaces with intrinsic antibacterial activity. A range of measures to control bio-interfacial interactions including approaches that modify implant surface chemistry or topography to reduce the capacity of bacteria to colonise the surface, form biofilms and cause infections at the device interface and surrounding tissues are also reviewed.

In vitro testing and efficacy of poly-lactic acid coating incorporating antibiotic loaded coralline bioceramic on Ti6Al4V implant against Staphylococcus aureus

Biofilm formation on an implant surface is most commonly caused by the human pathogenic bacteria Staphylococcus aureus, which can lead to implant related infections and failure. It is a major problem for both implantable orthopedic and maxillofacial devices. The current antibiotic treatments are typically delivered orally or in an injectable form. They are not highly effective in preventing or removing biofilms, and they increase the risk of antibiotic resistance of bacteria and have a dose-dependent negative biological effect on human cells. Our aim was to improve current treatments via a localized and controlled antibiotic delivery-based implant coating system to deliver the antibiotic, gentamicin (Gm). The coating contains coral skeleton derived hydroxyapatite powders (HAp) that act as antibiotic carrier particles and have a biodegradable poly-lactic acid (PLA) thin film matrix. The system is designed to prevent implant related infections while avoiding the deleterious effects of high concentration antibiotics in implants on local cells including primary human adipose derived stem cells (ADSCs). Testing undertaken in this study measured the rate of S. aureus biofilm formation and determined the growth rate and proliferation of ADSCs. After 24 h, S. aureus biofilm formation and the percentage of live cells found on the surfaces of all 5%-30% (w/w) PLA-Gm-(HAp-Gm) coated Ti6Al4V implants was lower than the control samples. Furthermore, Ti6Al4V implants coated with up to 10% (w/w) PLA-Gm-(HAp-Gm) did not have noticeable Gm related adverse effect on ADSCs, as assessed by morphological and surface attachment analyses. These results support the use and application of the antibacterial PLA-Gm-(HAp-Gm) thin film coating design for implants, as an antibiotic release control mechanism to prevent implant-related infections.

Why Is Tantalum Less Susceptible to Bacterial Infection?

Periprosthetic infection is one of the trickiest clinical problems, which often leads to disastrous consequences. The emergence of tantalum and its derivatives provides novel ideas and effective methods to solve this problem and has attracted great attention. However, tantalum was reported to have different anti-infective effects in vivo and in vitro, and the inherent antibacterial capability of tantalum is still controversial, which may restrict its development as an antibacterial material to some extent. In this study, the polished tantalum was selected as the experimental object, the implant-related tibia osteomyelitis model was first established to observe whether it has an anti-infective effect in vivo compared to titanium, and the early studies found that the tantalum had a lower infectious state in the implant-related tibia osteomyelitis model in vivo than titanium. However, further in vitro studies found that the polished tantalum was not superior to the titanium against bacterial adhesion and antibacterial efficacy. In addition, we focus on the state of interaction between cells, bacteria and materials to restore the internal environment as realistically as possible. We found that the adhesion of fibroblasts to tantalum was faster and better than that of titanium. Moreover, what is more, interesting is that, in the early period, bacteria were more likely to adhere to cells that had already attached to the surface of tantalum than to the bare surface of it, and over time, the cells eventually fell off the biomaterials and took away more bacteria in tantalum, making it possible for tantalum to reduce the probability of infection in the body through this mechanism. Moreover, these results also explained the phenomenon of the "race for the surface" from a completely different perspective. This study provides a new idea for further exploring the relationship between bacteria and host tissue cells on the implant surface and a meaningful clue for optimizing the preparation of antibacterial implants in the future.

Functional and radiological outcomes of primary ring fixator versus antibiotic nail in open tibial diaphyseal fractures: A prospective study

BACKGROUND

Management of open fractures of tibia is still a matter of debate due to high incidence of infections. Traditionally external fixators have been advocated in managing open tibial fractures. Due to limited efficacy of systemic antibiotics, recently antibiotic coated intramedullary interlocking nails have been developed for the management of open tibia fractures. Therefore, we conducted this prospective randomized study to compare the functional and radiological outcomes of primary ring fixator versus antibiotic coated nail in open diaphyseal tibial fractures.

METHODS

The study included 32 patients with Gustilo-Anderson type II and type IIIA fractures of tibial diaphysis. Out of them 16 patients were managed with Ring External Fixator (Group I) and 16 were managed with Ossipro^Ò gentamicin intramedullary interlocking tibial nail (Group II). The radiological and functional outcomes were assessed at final follow-up according to and SMFA criteria. Statistical analysis of the data was performed using IBM SPSS statistics 2.0 software. Chi square test and independent student t-test were used and a P value <0.05 was considered statistically significant RESULTS: Union was achieved in 15 patients (93.8%) in group I and 13 patients (81.2%) in group II. Pin tract infection was seen in 6 patients (37.5%) in group I, whereas infection was present in 2 patients (12.5%) in group II. Bone results were excellent in 13 patients (81.3%), good in 2 patients (12.5%), poor in one patient (6.3%). In group II, bone results were excellent in 12 patients (75%), good in one patient (6.2%), poor in 3 patients (18.8%). At 1 year of final follow up, mean SMFA score was 24.41±5.87 in group I, whereas mean SMFA score was 23.703±8.02 in group II.

CONCLUSION

Ring fixator as well as antibiotic coated tibial interlocking nail achieved comparable rates of union in the present study. Complication rates were similar in both the groups and the functional and radiological outcomes were comparable in both groups. Results of this study indicate that although ring fixation is an established option for management of open tibial fractures, antibiotic-coated intramedullary nail is also a reliable option in open Grade II and grade IIIA injuries.

LEVEL OF EVIDENCE

Level II.

Polymer–Metal Composite Healthcare Materials: From Nano to Device Scale

Metals have been investigated as biomaterials for a wide range of medical applications. At nanoscale, some metals, such as gold nanoparticles, exhibit plasmonics, which have motivated researchers’ focus on biosensor development. At the device level, some metals, such as titanium, exhibit good physical properties, which could allow them to act as biomedical implants for physical support. Despite these attractive features, the non-specific delivery of metallic nanoparticles and poor tissue–device compatibility have greatly limited their performance. This review aims to illustrate the interplay between polymers and metals, and to highlight the pivotal role of polymer–metal composite/nanocomposite healthcare materials in different biomedical applications. Here, we revisit the recent plasmonic engineered platforms for biomolecules detection in cell-free samples and highlight updated nanocomposite design for (1) intracellular RNA detection, (2) photothermal therapy, and (3) nanomedicine for neurodegenerative diseases, as selected significant live cell–interactive biomedical applications. At the device scale, the rational design of polymer–metallic medical devices is of importance for dental and cardiovascular implantation to overcome the poor physical load transfer between tissues and devices, as well as implant compatibility under a dynamic fluidic environment, respectively. Finally, we conclude the treatment of these innovative polymer–metal biomedical composite designs and provide a future perspective on the aforementioned research areas.

The Influence of Copper Content on the Elastic Modulus and Antibacterial Properties of Ti-13Nb-13Zr-xCu Alloy

Device-related infection or inflammatory and stress shield are still the main problems faced by titanium alloy implants for long-term implantation application; therefore, it is of great significance to design an alloy with low elastic modulus and good antibacterial properties as well as good biocompatibility. In this paper, Ti-13Nb-13Zr-xCu(x = 3, 7 wt.%) alloys were designed and prepared to reveal the influence of Cu content on the elastic modulus and antibacterial property. X-ray diffractometer, metallographic microscope, scanning electron microscope, and transmission electron microscope were used to study the phase transformation, microstructure, mechanical properties, antibacterial properties, and cytotoxicity of the alloys. The experimental results have demonstrated that the antibacterial performance and the elastic modulus were significantly improved but the corrosion resistance deteriorated with the increase of the copper content. Ti-13Nb-13Zr-3Cu with a low modulus of 73 GPa and an antibacterial rate of over 90% against Staphylococcus aureus (S. aureus) exhibited great potential as a candidate for implant titanium in the future.

3D-Printed Gentamicin-Releasing Poly-ε-Caprolactone Composite Prevents Fracture-Related Staphylococcus aureus Infection in Mice

Bacterial infections are a serious healthcare complication in orthopedic and trauma surgery worldwide. Compared to systemic, local antibiotic prophylaxis has been shown to provide a higher antibiotic dose and bioavailability at the bone site with minimum toxic effects. However, there are still not enough biomaterial and antibiotic combinations available for personalized implant sizes for patients. The aim of this study was to develop a bone fixation plate coating made of a composite of poly-ε-caprolactone, hydroxyapatite and halloysite nanotubes loaded with gentamicin sulphate and fabricated via fused filament fabrication 3D printing technology. The mechanical and thermal properties of the biomaterial were analyzed. The in vitro release kinetics of gentamicin sulphate were evaluated for 14 days showing a burst release during the first two days that was followed by a sustained release of bactericidal concentrations. The composite loaded with 2 and 5% gentamicin sulphate exhibited complete antimicrobial killing of Staphylococcus aureus in an ex vivo mouse femur fixation plate infection model. Moreover, a fixation plate of the composite loaded with 5% of gentamicin sulphate was able to prevent S. aureus infection in the bone and surrounding tissue in an in vivo mouse bone fixation plate infection model 3 days post-surgery. In conclusion, the newly developed composite material successfully prevented infection in vivo. Additionally, the ability to use fused filament fabrication 3D printing to produce patient-specific implants may provide a wider range of personalized solutions for patients.

A Journey into Animal Models of Human Osteomyelitis: A Review

Osteomyelitis is an infection of the bone characterized by progressive inflammatory destruction and apposition of new bone that can spread via the hematogenous route (hematogenous osteomyelitis (HO)), contiguous spread (contiguous osteomyelitis (CO)), and direct inoculation (osteomyelitis associated with peripheral vascular insufficiency (PVI)). Given the significant financial burden posed by osteomyelitis patient management, the development of new preventive and treatment methods is warranted. To achieve this objective, implementing animal models (AMs) of infection such as rats, mice, rabbits, avians, dogs, sheep, goats, and pigs might be of the essence. This review provides a literature analysis of the AMs developed and used to study osteomyelitis. Historical relevance and clinical applicability were taken into account to choose the best AMs, and some study methods are briefly described. Furthermore, the most significant strengths and limitations of each species as AM are discussed, as no single model incorporates all features of osteomyelitis. HO’s clinical manifestation results in extreme variability between patients due to multiple variables (e.g., age, sex, route of infection, anatomical location, and concomitant diseases) that could alter clinical studies. However, these variables can be controlled and tested through different animal models.

Animal Models for Postoperative Implant‐Related Spinal Infection

Postoperative infections following implant‐related spinal surgery are severe and disastrous complications for both orthopaedic surgeons and patients worldwide. They can cause neurological damage, disability, and death. To better understand the mechanism of these destructive complications and intervene in the process, further research is needed. Therefore, there is an urgent need for efficient, accurate, and easily available animal models to study the pathogenesis of spinal infections and develop new and effective anti‐bacterial methods. In this paper, we provide a general review of the commonly used animal models of postoperative implant‐related spinal infections, describe their advantages and disadvantages, and highlight the significance of correctly choosing the model according to the infection aspect under investigation. These models are valuable tools contributing to the better understanding of postoperative spinal infections and will continue to facilitate the invention of novel preventative and treatment strategies for patients with postoperative spinal infections. However, although they are valid and reproducible in some respects, the current animal models present certain limitations. Future ideal spinal infection animal models may assess the bacterial load of the same animal in real‐time in vivo, and better mimic the human anatomy as well as surgical techniques. Strains other than Staphylococcus aureus account for a large proportion of postoperative spinal infections, and thus, the establishment of models to evaluate other types of microbial infections is expected in the future. Furthermore, novel transgenic models established on advancements in genome editing are also likely to be developed in the future.

Establishment of a reliable in-vivo model of implant-associated infection to investigate innovative treatment options

The increasing number of implant-associated infections and of multiresistant pathogens is a major problem in the daily routine. In the field of osteomyelitis, it is difficult to manage a valid clinical study because of multiple influencing factors. Therefore, models of osteomyelitis with a simulation of the pathophysiology to evaluate treatment options for implant-associated infections are necessary. The aim of this study is to develop a standardized and reproducible osteomyelitis model in-vivo to improve treatment options. This study analyses the influence of a post-infectious implant exchange one week after infection and the infection progress afterward in combination with a systemic versus a local antibiotic treatment in-vivo. Therefore, the implant exchange, the exchange to a local drug-delivery system with gentamicin, and the implant removal are examined. Furthermore, the influence of an additional systemic antibiotic therapy is evaluated. An in-vivo model concerning the implant exchange is established that analyzes clinic, radiologic, microbiologic, histologic, and immunohistochemical diagnostics to obtain detailed evaluation and clinical reproducibility. Our study shows a clear advantage of the combined local and systemic antibiotic treatment in contrast to the implant removal and to a non-combined antibiotic therapy. Group genta/syst. showed the lowest infection rate with a percentage of 62.5% concerning microbiologic analysis, which is in accordance with the immunohistochemical, cytochemical, histologic, and radiologic analysis. Our in-vivo rat model has shown valid and reproducible results, which will lead to further investigations regarding treatment options and influencing factors concerning the therapy of osteomyelitis and implant-associated infections.

Latest Trends in Surface Modification for Dental Implantology: Innovative Developments and Analytical Applications

An increase in the world population and its life expectancy, as well as the ongoing concern about our physical appearance, have elevated the relevance of dental implantology in recent decades. Engineering strategies to improve the survival rate of dental implants have been widely investigated, focusing on implant material composition, geometry (usually guided to reduce stiffness), and interface surrounding tissues. Although efforts to develop different implant surface modifications are being applied in commercial dental prostheses today, the inclusion of surface coatings has gained special interest, as they can be tailored to efficiently enhance osseointegration, as well as to reduce bacterial-related infection, minimizing peri-implantitis appearance and its associated risks. The use of biomaterials to replace teeth has highlighted the need for the development of reliable analytical methods to assess the therapeutic benefits of implants. This literature review considers the state-of-the-art strategies for surface modification or coating and analytical methodologies for increasing the survival rate for teeth restoration.

Perspectives in Prevention of Biofilm for Medical Applications

The opportunity of decreasing the development of biofilm on the implant surface is one of the biggest research problems. It is connected with the existing prevention of microorganism hyperplasia. The application of numerous modifications is concerned with surface treatments leading to minimizing bacterial colonization. In the case of non-use antibacterial therapy, this leads to tissue infection. It can lead to a decreased opportunity to fight infection using antibiotherapy. One way is to decrease the increasing biofilm application which requires a method of modification. These techniques ensure properties like homogeneity or repeatability. The structure and chemical composition are changed with methods like CVD (Chemical Vapor Deposition), PVD (Physical Vapor Deposition), sol–gel, or ALD (Atomic Layer Deposition). Antibacterial properties of metals are connected with their impact on proteins and the nuclear proliferation of fibroblasts, causing improvement in biocompatibility and also growth corrosion resistance, and the decline of biofilm adhesion. The prevention of biofilm with medicines and antibiotics is a crowded-out treatment. Traditional methods of preventing biofilm are based on compounds that kill or inhibit the growth of the microbes but at the same time lead to frequent development of resistance to antibiotics. This review summarizes the current knowledge of reducing and preventing the creation of biofilm.

Recent Advances in the Evaluation of Antimicrobial Materials for Resolution of Orthopedic Implant-Associated Infections In Vivo

While orthopedic implant-associated infections are rare, revision surgeries resulting from infections incur considerable healthcare costs and represent a substantial research area clinically, in academia, and in industry. In recent years, there have been numerous advances in the development of antimicrobial strategies for the prevention and treatment of orthopedic implant-associated infections which offer promise to improve the limitations of existing delivery systems through local and controlled release of antimicrobial agents. Prior to translation to in vivo orthopedic implant-associated infection models, the properties (e.g., degradation, antimicrobial activity, biocompatibility) of the antimicrobial materials can be evaluated in subcutaneous implant in vivo models. The antimicrobial materials are then incorporated into in vivo implant models to evaluate the efficacy of using the material to prevent or treat implant-associated infections. Recent technological advances such as 3D-printing, bacterial genomic sequencing, and real-time in vivo imaging of infection and inflammation have contributed to the development of preclinical implant-associated infection models that more effectively recapitulate the clinical presentation of infections and improve the evaluation of antimicrobial materials. This Review highlights the advantages and limitations of antimicrobial materials used in conjunction with orthopedic implants for the prevention and treatment of orthopedic implant-associated infections and discusses how these materials are evaluated in preclinical in vivo models. This analysis serves as a resource for biomaterial researchers in the selection of an appropriate orthopedic implant-associated infection preclinical model to evaluate novel antimicrobial materials.

Review on Surface Treatment for Implant Infection via Gentamicin and Antibiotic Releasing Coatings

Surface treatment of metallic implants plays a crucial role in orthopedics and orthodontics. Metallic implants produce side-effects such as physical, chemical/electro-chemical irritations, oligodynamic/catalytic and carcinogenic effects. These effects cause bacterial infections and account for huge medical expenses. Treatment for these infections comprises repeated radical debridement, replacement of the implant device and intravenous or oral injection antibiotics. Infection is due to the presence of bacteria in the patient or the surrounding environment. The antibiotic-based medication prevents prophylaxis against bacterial colonization, which is an emphatic method that may otherwise be catastrophic to a patient. Therefore, preventive measures are essential. A coating process was developed with its drug infusion and effect opposing biofilms. Modification in the medical implant surface reduces the adhesion of bacterial and biofilms, the reason behind bacterial attachment. Other polymer-based and nanoparticle-based carriers are used to resolve implant infections. Therefore, using an implant coating is a better approach to prevent infection due to biofilm.

Development of an anti-infective coating on the surface of intraosseous implants responsive to enzymes and bacteria

Background

Bacterial proliferation on the endosseous implants surface presents a new threat to the using of the bone implants. Unfortunately, there is no effective constructed antibacterial coating which is bacterial anti-adhesion substrate-independent or have long-term biofilm inhibition functions.

Methods

Drug release effect was tested in Chymotrypsin (CMS) solution and S. aureus. We used bacterial inhibition rate assays and protein leakage experiment to analyze the in vitro antibacterial effect of (Montmorillonite/Poly-l-lysine-Chlorhexidine)₁₀ [(MMT/PLL-CHX)₁₀] multilayer film. We used the CCK-8 assay to analyze the effect of (MMT/PLL-CHX)₁₀ multilayer films on the growth and proliferation of rat osteoblasts. Rat orthopaedic implant-related infections model was constructed to test the antimicrobial activity effect of (MMT/PLL-CHX)₁₀ multilayer films in vivo.

Results

In this study, the (MMT/PLL-CHX)₁₀ multilayer films structure were progressively degraded and showed well concentration-dependent degradation characteristics following incubation with Staphylococcus aureus and CMS solution. Bacterial inhibition rate assays and protein leakage experiment showed high levels of bactericidal activity. While the CCK-8 analysis proved that the (MMT/PLL-CHX)₁₀ multilayer films possess perfect biocompatibility. It is somewhat encouraging that in the in vivo antibacterial tests, the K-wires coated with (MMT/PLL-CHX)₁₀ multilayer films showed lower infections incidence and inflammation than the unmodified group, and all parameters are close to SHAM group.

Conclusion

(MMT/PLL-CHX)₁₀ multilayer films provides a potential therapeutic method for orthopaedic implant-related infections.

Mimicking biofilm formation and development: Recent progress in in vitro and in vivo biofilm models

Biofilm formation in living organisms is associated to tissue and implant infections, and it has also been linked to the contribution of antibiotic resistance. Thus, understanding biofilm development and being able to mimic such processes is vital for the successful development of antibiofilm treatments and therapies. Several decades of research have contributed to building the foundation for developing in vitro and in vivo biofilm models. However, no such thing as an "all fit" in vitro or in vivo biofilm models is currently available. In this review, in addition to presenting an updated overview of biofilm formation, we critically revise recent approaches for the improvement of in vitro and in vivo biofilm models.

Antimicrobial and enzyme-responsive multi-peptide surfaces for bone-anchored devices

Functionalization of dental and orthopedic implants with multiple bioactivities is desirable to obtain surfaces with improved biological performance and reduced infection rates. While many approaches have been explored to date, nearly all functionalized surfaces are static, i.e., non-responsive to biological cues. However, tissue remodeling necessary for implant integration features an ever-changing milieu of cells that demands a responsive biomaterial surface for temporal synchronization of interactions between biomaterial and tissue. Here, we successfully synthesized a multi-functional, dynamic coating on titanium by co-immobilizing GL13K antimicrobial peptide and an MMP-9 - a matrix metalloproteinase secreted by bone-remodeling osteoclasts - responsive peptide. Our co-immobilized peptide surface showed potent anti-biofilm activity, enabled effective osteoblast and fibroblast proliferation, and demonstrated stability against a mechanical challenge. Finally, we showed peptide release was triggered for up to seven days when the multi-peptide coatings were cultured with MMP-9-secreting osteoclasts. Our MMP-9 cleavable peptide can be conjugated with osteogenic or immunomodulatory motifs for enhanced bone formation in future work. Overall, we envisage our multifunctional, dynamic surface to reduce infection rates of percutaneous bone-anchored devices via strong anti-microbial activity and enhanced tissue regeneration via temporal synchronization between biomaterial cues and tissue responses.

Tailoring the immobilization and release of chlorhexidine using dopamine chemistry to fight infections associated to orthopedic devices

A crucial factor in the pathogenesis of orthopedics associated infections is that bacteria do not only colonize the implant surface but also the surrounding tissues. This study aimed to engineer an antimicrobial release coating for stainless steel (SS) surfaces, to impart them with the ability to prevent Staphylococci colonization. Chlorhexidine (CHX) was immobilized using two polydopamine (pDA)-based approaches: a one-pot synthesis, where CHX is dissolved together with dopamine before its polymerization; and a two-step methodology, comprising the deposition of a pDA layer to which CHX is immobilized. To modulate CHX release, an additional layer of pDA was also added for both strategies. Immobilization of CHX using a one-step approach yielded surfaces with a more homogenous coating and less roughness than the other strategies. The amount of released CHX was lower for the one-step approach, as opposed to the two-step approach yielding the higher release, which could be decreased by applying an outward layer of pDA. Both one and two-step approaches provided the surfaces with the ability to prevent bacterial colonization of the surface itself and kill most of bacteria in the bulk phase up to 10 days. This long-term antimicrobial performance alluded a stable and enduring immobilization of CHX. In terms of biocompatibility, the amount of CHX released from the one-step approach did not compromise the growth of mammalian cells, contrary to the two-step strategy. Additionally, the few bacteria that managed to adhere to surfaces modified with one-step approach did not show evidence of resistance towards CHX. Overall data underline that one-step immobilization of CHX holds great potential to be further applied in the fight against orthopedic devices associated infections.

Targeting implant-associated infections: titanium surface loaded with antimicrobial

Implant devices have = proven a successful treatment modality in reconstructive surgeries. However, increasing rates of peri-implant diseases demand further examination of their pathogenesis. Polymicrobial biofilm formation on titanium surfaces has been considered the main risk factor for inflammatory processes on tissues surrounding implant devices, which often lead to implant failure. To overcome microbial accumulation on titanium surfaces biofilm targeting strategies have been developed to modify the surface and incorporate antimicrobial coatings. Because antibiotics are widely used to treat polymicrobial infections, these agents have recently started to be incorporated on titanium surface. This review discusses the biofilm formation on titanium dental implants and key factors to be considered in therapeutic and preventative strategies. Moreover, a systematic review was conducted on coatings developed for titanium surfaces using different antibiotics. This review will also shed light on potential alternative strategies aiming to reduce microbial loads and control polymicrobial infection on implanted devices.

New developments in anti-biofilm intervention towards effective management of orthopedic device related infections (ODRI's)

Orthopedic device related infections (ODRI's) represent a difficult to treat situation owing to their biofilm based nature. Biofilm infections once established are difficult to eradicate even with an aggressive treatment regimen due to their recalcitrance towards antibiotics and immune attack. The involvement of antibiotic resistant pathogens as the etiological agent further worsens the overall clinical picture, pressing on the need to look into alternative treatment strategies. The present review highlightes the microbiological challenges associated with treatment of ODRI's due to biofilm formation on the implant surface. Further, it details the newer anti-infective modalities that work either by preventing biofilm formation and/or through effective disruption of the mature biofilms formed on the medical implant. The study, therefore aims to provide a comprehensive insight into the newer anti-biofilm interventions (non-antibiotic approaches) and a better understanding of their mechanism of action essential for improved management of orthopedic implant infections.

Bioinspired antibacterial surface for orthopedic and dental implants

Bacterial infections still present a significant concern in orthopedic and dental implant failure. Previous investigations have focused on modifying the surface texture, roughness, or coating implants with antibiotics to provide enhanced anti-bacterial properties. However, they have demonstrated limited success. In this study, we attempted to engineer the titanium (Ti) alloy surface biomimetically at the nano level using alkaline hydrothermal treatment (AHT) inspired by cicada's wing structure. Two modified surfaces of Ti plates were developed using 4 and 8-hr AHT at 230°C. We found that the control plates showed a relatively smooth surface, with little artifacts on the surface. In contrast, 4-hr AHT and 8-hr AHT plates showed nano-spikes of heights around 250-350 and 100-1,250 nm, respectively, that were distributed randomly all over the surface. We found a statistically significant (p < 0.05) number of non-viable cells for both S. aureus and P. aeruginosa bacterial strains when incubated for 1 hr in a dynamic environment when compared with the control group. The 8-hr AHT groups killed 38.97% more S. aureus in static culture and 11.27% in a dynamic environment than the 4-hr AHT. Overall, the findings indicate that the nanostructures generated on titanium by the AHT showed significant bactericidal properties. We, therefore, recommend conducting alkaline hydrothermal treatment on the surfaces for future orthopedic and dental metallic implants.

Disinfection of contaminated metal implants with an Er:YAG laser

Infections related to orthopedic procedures are considered particularly severe when implantation materials are used, because effective treatments for biofilm removal are lacking. In this study, the relatively new approach for infection control by using an erbium:yttrium-aluminum-garnet (Er:YAG) laser was tested. This laser vaporizes all water containing cells in a very effective, precise, and predictable manner and results in only minimal thermal damage. For preliminary testing, 42 steel plates and 42 pins were seeded with mixed cultures. First, the minimally necessary laser energy for biofilm removal was determined. Subsequently, the effectiveness of biofilm removal with the Er:YAG laser and the cleansing of the metal implants with octenidine-soaked gauze was compared. Then, we compared the effectiveness of biofilm removal on 207 steel pins from 41 patients directly after explantation. Sonication and scanning electron microscopy were used for analysis. Laser fluences exceeding 2.8  J/cm² caused a complete extinction of all living cells by a single-laser impulse. Cleansing with octenidine-soaked gauze and irradiation with the Er:YAG laser are both thoroughly effective when applied to seeded pins. In contrast, when explanted pins with fully developed biofilms were analyzed, we found a significant advantage of the laser procedure. The Er:YAG laser offers a secure, complete, and nontoxic eradication of all kinds of pathogens from metal implants without damaging the implant and without the possible development of resistance. The precise noncontact removal of adjacent tissue is a decisive advantage over conventional disinfectants. Therefore, laser irradiation could become a valuable method in every debridement, antibiotics, and implant retention procedure.

An intravenous application of magnetic nanoparticles for osteomyelitis treatment: An efficient alternative

The infection of bone and bone marrow is called osteomyelitis. Treatment is difficult since antibiotics can not reach with enough concentration to the infected area. For the first time in this study, we have developed gentamicin-loaded magnetic gelatin nanoparticles (GMGNPs) for nanocarrier-mediated and magnetically targeted osteomyelitis therapy. Gelatin, genipin, and magnetite were used for preparation of that novel carrier system due to their biodegradable and biocompatible properties. Cross-linking degree of gelatin nanoparticles, concentration of magnetite nanoparticles, and adsorbed drug amount were optimized. Furthermore, nanoparticles were characterized and the drug release profile was determined. The osteomyelitis model was constituted in the proximal tibia of rats. The therapeutic potential of GMGNPs on rats was monitored via X-Ray radiography and hematological and histopathological analyses were performed. According to the results, 110.3 ± 8.2 µg gentamicin/mg GMGNPs were used, hydrodynamic size was measured as 253.7 ± 11.8 nm, and GMGNPs have controlled drug release profile. Based on in vivo and ex vivo studies, after six doses of GMGNPs treatment, abscess began to heal and the integrity of periost and bone began to reconstruct. In conclusion, it can be suggested that GMGNPs could provide efficient therapy for osteomyelitis.

Therapeutics and delivery vehicles for local treatment of osteomyelitis

Osteomyelitis, or the infection of the bone, presents a major complication in orthopedics and may lead to prolonged hospital visits, implant failure, and in more extreme cases, amputation of affected limbs. Typical treatment for this disease involves surgical debridement followed by long-term, systemic antibiotic administration, which contributes to the development of antibiotic-resistant bacteria and has limited ability to eradicate challenging biofilm-forming pathogens including Staphylococcus aureus-the most common cause of osteomyelitis. Local delivery of high doses of antibiotics via traditional bone cement can reduce systemic side effects of an antibiotic. Nonetheless, growing concerns over burst release (then subtherapeutic dose) of antibiotics, along with microbial colonization of the nondegradable cement biomaterial, further exacerbate antibiotic resistance and highlight the need to engineer alternative antimicrobial therapeutics and local delivery vehicles with increased efficacy against, in particular, biofilm-forming, antibiotic-resistant bacteria. Furthermore, limited guidance exists regarding both standardized formulation protocols and validated assays to predict efficacy of a therapeutic against multiple strains of bacteria. Ideally, antimicrobial strategies would be highly specific while exhibiting a broad spectrum of bactericidal activity. With a focus on S. aureus infection, this review addresses the efficacy of novel therapeutics and local delivery vehicles, as alternatives to the traditional antibiotic regimens. The aim of this review is to discuss these components with regards to long bone osteomyelitis and to encourage positive directions for future research efforts.

A tailored positively-charged hydrophobic surface reduces the risk of implant associated infections

Implant-associated infections is one of the most challenging post-operative complications in bone-related implantations. To tackle this clinical issue, we developed a low-cost and durable surface coating for medical grade titanium implants that uses positively charged silane molecules. The in vitro antimicrobial tests revealed that the titanium surface coated with (3-aminopropyl) triethoxysilane, which has the appropriate length of hydrophobic alkyl chain and positive charged amino group, suppressed more than 90% of the initial bacterial adhesion of S. aureus, P. aeruginosa, and E. coli after 30 min of incubation. In terms of growth inhibitory rate, the treated surface was able to reduce 75.7% ± 11.9% of bacterial growth after a 24-hour culturing, thereby exhibiting superior anti-biofilm formation in the late stage. When implanted into the rat model infected by S. aureus, the treated surface eliminated the implant-associated infection through the mechanism of inhibition of bacterial adhesion on the implant surface. Additionally, the treated surface was highly compatible with mammalian cells. In general, our design demonstrated its potential for human clinical trials as a low-cost and effective antibacterial strategy to minimize post-operative implant-related bacterial infection.

Nanostructured Biomaterials for Bone Regeneration

This review article addresses the various aspects of nano-biomaterials used in or being pursued for the purpose of promoting bone regeneration. In the last decade, significant growth in the fields of polymer sciences, nanotechnology, and biotechnology has resulted in the development of new nano-biomaterials. These are extensively explored as drug delivery carriers and as implantable devices. At the interface of nanomaterials and biological systems, the organic and synthetic worlds have merged over the past two decades, forming a new scientific field incorporating nano-material design for biological applications. For this field to evolve, there is a need to understand the dynamic forces and molecular components that shape these interactions and influence function, while also considering safety. While there is still much to learn about the bio-physicochemical interactions at the interface, we are at a point where pockets of accumulated knowledge can provide a conceptual framework to guide further exploration and inform future product development. This review is intended as a resource for academics, scientists, and physicians working in the field of orthopedics and bone repair.

Evaluation of Antibacterial and Cytotoxic Properties of a Fluorinated Diamond-Like Carbon Coating for the Development of Antibacterial Medical Implants

Peri-implant infection is a serious complication in surgical procedures involving implants. We conducted an in vitro study to determine whether the use of a fluorinated diamond-like carbon (F-DLC) coating on a titanium alloy surface can prevent peri-implant infection. After applying the F-DLC, we evaluated its antibacterial and cytotoxic properties. The coating groups, containing controlled fluorine concentrations of 5.44%, 17.43%, 24.09%, and 30%, were examined for the presence of Staphylococcus aureus and Escherichia coli according to ISO 22196 for the measurement of antibacterial activity on plastics and other nonporous surfaces. Biological toxicity was evaluated using Chinese hamster V79 cells according to ISO 10993-5 for the biological evaluation of medical devices. In the control group, populations of S. aureus and E. coli substantially increased from 2.4 × 10⁴ to (1.45 ± 1.11) × 10⁶ colony-forming units (CFUs) and from 2.54 × 10⁴ to (4.04 ± 0.44) × 10⁶ CFUs, respectively. However, no bacteria colonies were detected in any F-DLC group with a fluorine concentration of ≥ 17.43%. In the biological toxicity study, an F-DLC coating with a fluorine concentration of 30% showed a colony formation rate of 105.8 ± 24.1%, which did not differ significantly from the colony formation rate of 107.5 ± 31.1% in the nontoxic control group. An F-DLC coating on titanium alloy discs showed excellent in vitro antibacterial activity with no biological toxicity.

Is coating of titanium implants effective at preventing Staphylococcus aureus infections? A meta-analysis of animal model studies

AIM OF THE STUDY

To assess the effects of the available coating methods against methicillin-resistant Staphylococcus aureus (MRSA) and methicillin-susceptible S. aureus (MSSA) biofilm development on titanium implants.

METHODS

We searched the MEDLINE, Embase, and CENTRAL databases until May 18, 2019, for studies that used animal models of infections to evaluate various titanium implant coating methods to prevent S. aureus infection. Twenty-seven studies were eligible for inclusion in qualitative synthesis. Of those, twenty-three were considered in pair-wise meta-analysis. In addition, subgroup analysis of implant protection strategies relative to uncoated controls was performed, and any adverse events stemming from the coating applications were reported. Quality assessment was performed using SYRCLE's risk of bias tool for animal studies.

RESULTS

Meta-analysis showed that active coating with antibiotics was favoured over uncoated controls (standardised mean differences [SMD] for MRSA and MSSA were - 2.71 [95% CI, - 4.24 to - 1.18], p = 0.0005, and - 2.5 [- 3.79 to - 1.22], p = 0.0001, respectively). Likewise, large effect sizes were demonstrated when a combination of active and conventional non-degradable passive coatings was compared with controls (SMDs for MRSA and MSSA were - 0.62 [95% CI, - 1.15 to - 0.08], p = 0.02, and - 1.93 [95% CI, - 2.87 to - 0.98], p < 0.001, respectively).

DISCUSSION/CONCLUSION

As a standalone prevention method, active titanium coating with antibiotics yielded promising results against both MSSA and MRSA. Combinations between active and non-degradable passive coatings, potentially allowing for sustained antimicrobial substance release, provided consistent hardware infection protection. Thus, we recommend that future research efforts focus on combined coating modalities against S. aureus biofilm infections in the presence of titanium implants.

SYSTEMATIC REVIEW REGISTRATION

CRD42019123462.

Customized Therapeutic Surface Coatings for Dental Implants

Dental implants are frequently used to support fixed or removable dental prostheses to replace missing teeth. The clinical success of titanium dental implants is owed to the exceptional biocompatibility and osseointegration with the bone. Therefore, the enhanced therapeutic effectiveness of dental implants had always been preferred. Several concepts for implant coating and local drug delivery had been developed during the last decades. A drug is generally released by diffusion-controlled, solvent-controlled, and chemical controlled methods. Although a range of surface modifications and coatings (antimicrobial, bioactive, therapeutic drugs) have been explored for dental implants, it is still a long way from designing sophisticated therapeutic implant surfaces to achieve the specific needs of dental patients. The present article reviews various interdisciplinary aspects of surface coatings on dental implants from the perspectives of biomaterials, coatings, drug release, and related therapeutic effects. Additionally, the various types of implant coatings, localized drug release from coatings, and how released agents influence the bone–implant surface interface characteristics are discussed. This paper also highlights several strategies for local drug delivery and their limitations in dental implant coatings as some of these concepts are yet to be applied in clinical settings due to the specific requirements of individual patients.

Antimicrobial Silver Multilayer Coating for Prevention of Bacterial Colonization of Orthopedic Implants

Due to increasing rates of periprosthetic joint infections (PJI), new approaches are needed to minimize the infection risk. The first goal of this study was to modify a well-established infection model to test surface-active antimicrobial systems. The second goal was to evaluate the antimicrobial activity of a silver multilayer (SML) coating. In vitro tests with SML items showed a >4 Log reduction in a proliferation assay and a 2.2 Log reduction in an agar immersion test (7 d). In the in vivo model blank and SML coated K-wires were seeded with ~2 × 104 CFU of a methicillin-sensitive Staphylococcus epidermidis (MSSE) and inserted into the intramedullary tibial canal of rabbits. After 7 days, the animals were sacrificed and a clinical, microbiological and histological analysis was performed. Microbiology showed a 1.6 Log pathogen reduction on the surface of SML items (p = 0.022) and in loosely attached tissue (p = 0.012). In the SML group 7 of 12 SML items were completely free of pathogens (cure rate = 58%, p = 0.002), while only 1 of 12 blank items were free of pathogens (cure rate = 8%, p = 0.110). No silver was detected in the blood or urine of the SML treated animals and only scarcely in the liver or adjacent lymph nodes. In summary, an in vivo infection model to test implants with bacterial pre-incubation was established and the antimicrobial activity of the SML coating was successfully proven.

Initiated Chemical Vapor Deposition of Crosslinked Organic Coatings for Controlling Gentamicin Delivery

A coating consisting of a copolymer of methacrylic acid and ethylene glycol dimethacrylate was deposited over a gentamicin film by initiated chemical vapor deposition with the aim of controlling the drug release. Gentamicin release in water was monitored by means of conductance measurements and of UV-vis Fluorescence Spectroscopy. The influence of the polymer chemical composition, specifically of its crosslinking density, has been investigated as a tool to control the swelling behavior of the initiated chemical vapor deposition (iCVD) coating in water, and therefore its ability to release the drug. Agar diffusion test and microbroth dilution assays against Staphylococcus aureus and Pseudomonas aeruginosa on cellulose coated substrates confirmed that the antibacterial activity of the drug released by the coating was retained, though the release of gentamicin was not complete.

The state of the art of osseointegration for limb prosthesis

Osseointegration (OI) is the direct attachment of bone onto a titanium implant. Recently, the term is used to describe "transdermal" implants that allow an external prosthesis to be connected directly to the skeleton. This technology eliminates the challenges of conventional socket-based prostheses, such as skin breakdown and poor fit, which are common in patients with major extremity amputations. Osseointegration patients demonstrate encouraging improvements in quality of life and function. Patients report improvement in prosthetic use, prosthetic mobility, global health, and pain reduction on a variety of clinical assessment tools. Various implants have been developed for osseointegration for amputees. These implants use a variety of fixation strategies and surface augments to allow for successful integration into the host bone. Regardless of design, all OI implants face similar challenges, particularly infections. Other challenges include the inability to determine when integration has occurred and the inability to detect loss of integration. These challenges may be met by incorporating sensing systems into the implants. The percutaneous nature of the metal devices can be leveraged so that internal sensors need not be wireless, and can be interrogated by external monitoring systems, thus providing crucial, real-time information about the state of the implant. The purpose of this review is to (1) review the basic science behind osseointegration, (2) provide an overview of current implants, practice patterns, and clinical outcomes, and (3) preview sensor technologies which may prove useful in future generations of transdermal orthopaedic implants.

Establishment of an in vivo rat model for chronic musculoskeletal implant infection

Background

The aim of the study was to establish an experimental chronic musculoskeletal infection model in vivo characterized by (a) a small bacterial inoculum, (b) no general or local signs of infection, (c) several parallels (implants) in each animal and finally (d) a model that is technically easy to perform.

Methods

Bone xenografts with steel plates were implanted intramuscularly in rats. To the xenografts, different inocula of Staphylococcus aureus and two strains of Staphylococcus epidermidis were added. The animals were observed for different time periods before the removal of the xenografts. The xenografts and steel plates were subjected to quantitative bacterial culture after sonication. Additional steel plates were subjected to scanning electron microscopy (SEM) for visualization of biofilm formation.

Results

Inoculation of bone grafts with S. aureus did produce a pyogenic infection in all animals. A chronic infection was established in rats where the bone grafts were inoculated with S. epidermidis. A bacterial inoculum of 100 colony-forming units (CFU) of S. epidermidis was adequate as a minimum infective dose. During a period of up until 42 days, the animals infected with S. epidermidis had no general or local signs of infection. According to the results of the quantitative bacterial culture of sonicate fluid and SEM, a biofilm was developed on all implants.

Conclusion

In the present in vivo model, a very small bacterial inoculum succeeded in establishing a chronic musculoskeletal implant infection where a biofilm was formed on the implants. The experimental model is easy to perform and allows several implants in each animal. The model could be useful for the study of biofilm formation in vivo on different implants and different surfaces.

Temperature-responsive PNDJ hydrogels provide high and sustained antimicrobial concentrations in surgical sites

Local antimicrobial delivery is a promising strategy for improving treatment of deep surgical site infections (SSIs) by eradicating bacteria that remain in the wound or around its margins after surgical debridement. Eradication of biofilm bacteria can require sustained exposure to high antimicrobial concentrations (we estimate 100-1000 μg/mL sustained for 24 h) which are far in excess of what can be provided by systemic administration. We have previously reported the development of temperature-responsive hydrogels based on poly(N-isopropylacrylamide-co-dimethylbutyrolactone acrylate-co-Jeffamine M-1000 acrylamide) (PNDJ) that provide sustained antimicrobial release in vitro and are effective in treating a rabbit model of osteomyelitis when instilled after surgical debridement. In this work, we sought to measure in vivo antimicrobial release from PNDJ hydrogels and the antimicrobial concentrations provided in adjacent tissues. PNDJ hydrogels containing tobramycin and vancomycin were administered in four dosing sites in rabbits (intramedullary in the femoral canal, soft tissue defect in the quadriceps, intramuscular injection in the hamstrings, and intra-articular injection in the knee). Gel and tissue were collected up to 72 h after dosing and drug levels were analyzed. In vivo antimicrobial release (43-95% after 72 h) was markedly faster than in vitro release. Drug levels varied significantly depending on the dosing site but not between polymer formulations tested. Notably, total antimicrobial concentrations in adjacent tissue in all dosing sites were sustained at estimated biofilm-eradicating levels for at least 24 h (461-3161 μg/mL at 24 h). These results suggest that antimicrobial-loaded PNDJ hydrogels are promising for improving the treatment of biofilm-based SSIs.

Evidence for inoculum size and gas interfaces as critical factors in bacterial biofilm formation on magnesium implants in an animal model

Infections of medical implants caused by bacterial biofilms are a major clinical problem. Bacterial colonization is predicted to be prevented by alkaline magnesium surfaces. However, in experimental animal studies, magnesium implants prolonged infections. The reason for this peculiarity likely lies within the ‒still largely hypothetical‒ mechanism by which infection arises. Investigating subcutaneous magnesium implants infected with bioluminescent Pseudomonas aeruginosa via in vivo imaging, we found that the rate of implant infections was critically dependent on a surprisingly high quantity of injected bacteria. At high inocula, bacteria were antibiotic-refractory immediately after infection. High cell densities are known to limit nutrient availability, restricting proliferation and trigger quorum sensing which could both contribute to the rapid initial resistance. We propose that gas bubbles such as those formed during magnesium corrosion, can then act as interfaces that support biofilm formation and permit long-term survival. This model could provide an explanation for the apparent ineffectiveness of innovative contact-dependent bactericidal implant surfaces in patients. In addition, the model points toward air bubbles in tissue, either by inclusion during surgery or by spontaneous gas bubble formation later on, could constitute a key risk factor for clinical implant infections.

Biomimetic multilayer coatings deliver gentamicin and reduce implant-related osteomyelitis in rats

Implant-related infections like periprosthetic joint infections (PJI) are still a challenging issue in orthopedic surgery. In this study, we present a prophylactic anti-infective approach based on a local delivery of the antibiotic gentamicin. The local delivery is achieved via a nanoscale polyelectrolyte multilayer (PEM) coating that leaves the bulk material properties of the implant unaffected while tuning the surface properties. The main components of the coating, i.e. polypeptides and sulfated glycosaminoglycans (sGAG) render this coating both biomimetic (matrix mimetic) and biodegradable. We show how adaptions in the conditions of the multilayer assembly process and the antibiotic loading process affect the amount of delivered gentamicin. The highest concentration of gentamicin could be loaded into films composed of polypeptide poly-glutamic acid when the pH of the loading solution was acidic. The concentration of gentamicin on the surface could be tailored with the number of deposited PEM layers. The resulting coatings reveal a bacteriotoxic effect on Staphylococcus cells but show no signs of cytotoxic effects on MC3T3-E1 osteoblasts. Moreover, when multilayer-coated titanium rods were implanted into contaminated medullae of rat tibiae, a reduction in the development of implant-related osteomyelitis was observed. This reduction was more pronounced for the multifunctional, matrix-mimetic heparin-based coatings that only deliver lower amounts of gentamicin.

Comparative study of the efficacy of gentamicin-coated intramedullary interlocking nail versus regular intramedullary interlocking nail in Gustilo type I and II open tibia fractures

PURPOSE

Open tibia fracture is prone to infection, consequently causing significant morbidity and increasing the hospital stay, occupational loss and onset of chronic osteomyelitis. Intramedullary nailing is one choice for treating tibia shaft fractures. To improve the delivery of antibiotics at the tissue-implant interface, many methods have been proposed as a part of prophylaxis against infection. This study was conducted to study the role of gentamicin-impregnated intramedullary interlocking (IMIL) nail in the prevention of infection in Gustilo type I and II open tibia fractures and to compare the results with regular intramedullary nail.

METHODS

The study included 28 patients with open tibia fractures (Gustilo type 1 or type 2); of them 14 underwent regular IMIL nailing and the other 14 were treated with gentamicin-coated nailing. Randomization was done by alternate allocation of the patients. Follow-up was done postoperatively (day 1), 1 week, 6 weeks, and 6 months for bone union, erythrocyte sedimentation rate (ESR), hemoglobin and C-reactive protein (CRP). Statistical significance was tested using unpaired t-test. A p value less than 0.05 was considered significant.

RESULTS

There were 4 cases of infection in controls (regular IMIL nail) and no infection among patients treated with gentamicin-coated nail during the follow up (X² = 4.66, p = 0.031). At 6 months postoperatively, CRP (p = 0.031), ESR (p = 0.046) and hemoglobin level (p = 0.016) showed significant difference between two groups. The bone healing rate was better with gentamicin-coated nail in comparison to regular IMIL nail at 6 months follow-up (p = 0.016).

CONCLUSION

Gentamicin-coated IMIL nail has a positive role in preventing infection in Gustilo type I and II open tibia fractures.

Treatment of implant-related methicillin-resistant Staphylococcus aureus osteomyelitis with vancomycin-loaded VK100 silicone cement: An experimental study in rats

INTRODUCTION

The purpose of this present study is to investigate the efficacy of vancomycin-loaded VK100 silicone cement drug delivery system in the treatment of implant-related methicillin-resistant Staphylococcus aureus (MRSA) osteomyelitis in rats.

MATERIALS AND METHODS

Thirty-six adult (18-20 weeks old) female Sprague-Dawley rats were included in the study. All rats underwent experimental osteomyelitis surgery via injecting 100 µL bacterial suspension of MRSA into the medullary canal. After a 2-week duration for the formation of osteomyelitis model, rats were assigned randomly into four groups: control (C), systemic vancomycin (V), local vancomycin-loaded VK100 silicone cement (vVK100), and systemic vancomycin and local vancomycin-loaded VK100 silicone cement (V+vVK100). The following treatment protocols were administered to each group for 4 weeks. For group C, 0.9% saline solution equivalent to the volume of vancomycin dose (approximately 1 ml/kg) was administered intraperitoneally twice daily (12-h intervals). For group V, 15 mg/kg of vancomycin was administered intraperitoneally twice daily (12-h intervals). For group vVK100, vVK100 polymer was included so that the intramedullary canal of the rats are affected. For group V+vVK100, vVK100 polymer was included so that the intramedullary canal of the rats are affected and 15 mg/kg of vancomycin was administered intraperitoneally twice daily (12-h intervals). After 4 weeks of treatment, clinical, radiologic, microbiologic, and histopathologic evaluations were performed for all groups.

RESULTS

Results of this study revealed that all scores of the evaluation criteria for the treatment groups (groups V, vVK100, and V+vVK100) decreased due to the treatment protocols when compared to group C. These results show the effectiveness of all treatment protocols for the implant-related chronic MRSA osteomyelitis. However, there were no statistical difference between these three protocols.

CONCLUSIONS

vVK100 polymer, as a local antibiotic delivery system, seems to be an effective method for the treatment of implant-related chronic MRSA osteomyelitis.