Electrochemical oxidation of histamine and serotonin at highly boron-doped diamond electrodes

Simultaneous detection of norepinephrine and 5-hydroxytryptophan using poly-alizarin/multi-walled carbon nanotubes-graphene modified carbon fiber microelectrode array sensor

Multi-walled carbon nanotubes, graphene and alizarin polymer composites coated carbon fiber microelectrode array sensor (p-AZ/MWCNT-GR/CFMEA) was constructed and used for the simultaneous detection of norepinephrine (NE) and 5-hydroxytryptophan (5-HT). The morphology and structural characteristics of sensor are characterized using scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Its electrochemical behavior has been studied with cyclic voltammetry and electrochemical impedance spectroscopy. The sensor exhibits excellent electrochemical activity for the oxidation of NE and 5-HT, two well separated oxidation peaks with the peak potential difference of 220 mV are observed on the cyclic voltammogram. NE and 5-HT both show two electrons and two protons electrochemical reaction on the p-AZ/MWCNT-GR/CFMEA. Under the optimized experiment conditions, the linear ranges of the sensor for NE and 5-HT are 0. 08- 8 μM and 0. 1-20 μM with detection limits of 4. 22 nM and 14. 2 nM (S/N = 3), respectively. In addition, the microsensor array show good reproducibility, stability and selectivity for the determination of NE and 5-HT. Finally, the p-AZ/MWCNT-GR/CFMEA is applied to the simultaneous detection of NE and 5-HT in human serum samples and macrophages.

Carbon nanospikes have improved sensitivity and antifouling properties for adenosine, hydrogen peroxide, and histamine

Carbon nanospikes (CNSs) are a new nanomaterial that has enhanced surface roughness and surface oxide concentration, increasing the sensitivity for dopamine detection. However, CNS-modified electrodes (CNSMEs) have not been characterized for other neurochemicals, particularly those with higher oxidation potentials. The purpose of this study was to evaluate CNSMEs for the detection of adenosine, hydrogen peroxide (H2O2), and histamine. The sensitivity increased with CNSs, and signals at CNSMEs were about 3.3 times higher than CFMEs. Normalizing for surface area differences using background currents, CNSMEs show an increased signal of 4.8 times for adenosine, 1.5 times for H2O2, and 2 times for histamine. CNSMEs promoted the formation of secondary products for adenosine and histamine, which enables differentiation from other analytes with similar oxidation potentials. CNSs also selectively enhance the sensitivity for adenosine and histamine compared to H2O2. A scan rate test reveals that adenosine is more adsorption-controlled at CNS electrodes than CFMEs. CNSMEs are antifouling for histamine, with less fouling because the polymers formed after histamine electrooxidation do not adsorb due to an elevated number of edge planes. CNSMEs were useful for detecting each analyte applied in brain slices. Because of the hydrophilic surface compared to CFMEs, CNSMEs also have reduced biofouling when used in tissue. Therefore, CNSMEs are useful for tissue measurements of adenosine, hydrogen peroxide, and histamine with high selectivity and low fouling.

Galvanic Redox Potentiometry for Fouling-Free and Stable Serotonin Sensing in a Living Animal Brain

Serotonin (5-HT) is a major neurotransmitter broadly involved in many aspects of feeling and behavior. Although its electro-activity makes it a promising candidate for electrochemical sensing, the persistent generation of fouling layers on the electrode by its oxidation products presents a hurdle for reliable sensing. Here, we present a fouling-free 5-HT sensor based on galvanic redox potentiometry. The sensor efficiently minimizes electrode fouling as revealed by in situ Raman spectroscopy, ensuring a less than 3 % signal change in a 2 hour continuous experiment, whereas amperometric sensors losing 90 % within 30 min. Most importantly, the sensor is highly amenable for in vivo studies, permitting real-time 5-HT monitoring, and supporting the mechanism associated with serotonin release in brain. Our system offers an effective way for sensing different neurochemicals having significant fouling issues, thus facilitating the molecular-level understanding of brain function.

Adsorption Kinetic Model Predicts and Improves Reliability of Electrochemical Serotonin Detection

Serotonin (5-HT) is a neurotransmitter involved in many biophysiological processes in the brain and in the gastrointestinal tract. Electrochemical methods are commonly used to quantify 5-HT, but their reliability may suffer due to the time-dependent nature of adsorption-limited 5-HT detection, as well as electrode fouling over repeated measurements. Mathematical characterization and modeling of adsorption-based electrochemical signal generation would improve reliability of 5-HT measurement. Here, a model was developed to track 5-HT electrode adsorption and resulting current output by combining Langmuir adsorption kinetic equations and adsorption-limited electrochemical equations. 5-HT adsorption binding parameters were experimentally determined at a carbon-nanotube coated Au electrode: K_D = 7 × 10^-7 M, k_on = 130 M^-1 s^-1, k_off = 9.1 × 10^-5 s^-1. A computational model of 5-HT adsorption was then constructed, which could effectively predict 5-HT fouling over 50 measurements (R² = 0.9947), as well as predict electrode responses over varying concentrations and measurement times. The model aided in optimizing the measurement of 5-HT secreted from a model enterochromaffin cell line-RIN14B-minimizing measurement time. The presented model simplified and improved the characterization of 5-HT detection at the selected electrode. This could be applied to many other adsorption-limited electrochemical analytes and electrode types, contributing to the improvement of application-specific modeling and optimization processes.

A Review on Bio- and Chemosensors for the Detection of Biogenic Amines in Food Safety Applications: The Status in 2022

This article provides an overview on the broad topic of biogenic amines (BAs) that are a persistent concern in the context of food quality and safety. They emerge mainly from the decomposition of amino acids in protein-rich food due to enzymes excreted by pathogenic bacteria that infect food under inappropriate storage conditions. While there are food authority regulations on the maximum allowed amounts of, e.g., histamine in fish, sensitive individuals can still suffer from medical conditions triggered by biogenic amines, and mass outbreaks of scombroid poisoning are reported regularly. We review first the classical techniques used for selective BA detection and quantification in analytical laboratories and focus then on sensor-based solutions aiming at on-site BA detection throughout the food chain. There are receptor-free chemosensors for BA detection and a vastly growing range of bio- and biomimetic sensors that employ receptors to enable selective molecular recognition. Regarding the receptors, we address enzymes, antibodies, molecularly imprinted polymers (MIPs), and aptamers as the most recent class of BA receptors. Furthermore, we address the underlying transducer technologies, including optical, electrochemical, mass-sensitive, and thermal-based sensing principles. The review concludes with an assessment on the persistent limitations of BA sensors, a technological forecast, and thoughts on short-term solutions.

Advances on Hormones and Steroids Determination: A Review of Voltammetric Methods since 2000

This article presents advances in the electrochemical determination of hormones and steroids since 2000. A wide spectrum of techniques and working electrodes have been involved in the reported measurements in order to obtain the lowest possible limits of detection. The voltammetric and polarographic techniques, due to their sensitivity and easiness, could be used as alternatives to other, more complicated, analytical assays. Still, growing interest in designing a new construction of the working electrodes enables us to prepare new measurement procedures and obtain lower limits of detection. A brief description of the measured compounds has been presented, along with a comparison of the obtained results.

Studies of Monoamine Neurotransmitters at Nanomolar Levels Using Carbon Material Electrodes: A Review

Neurotransmitters (NTs) with hydroxyl groups can now be identified electrochemically, utilizing a variety of electrodes and voltammetric techniques. In particular, in monoamine, the position of the hydroxyl groups might alter the sensing properties of a certain neurotransmitter. Numerous research studies using electrodes modified on their surfaces to better detect specific neurotransmitters when other interfering factors are present are reviewed to improve the precision of these measures. An investigation of the monoamine neurotransmitters at nanoscale using electrochemical methods is the primary goal of this review article. It will be used to determine which sort of electrode is ideal for this purpose. The use of carbon materials, such as graphite carbon fiber, carbon fiber micro-electrodes, glassy carbon, and 3D printed electrodes are only some of the electrodes with surface modifications that can be utilized for this purpose. Electrochemical methods for real-time detection and quantification of monoamine neurotransmitters in real samples at the nanomolar level are summarized in this paper.

Diamonds for Life: Developments in Sensors for Biomolecules

Diamond-based electrodes and biosensors are interesting in analytics because of their particular set of properties, namely: large potential window, chemical inertness, low baseline current, stability, and transparency. Diamond-based electrodes and biosensors were shown to detect biological molecules such as neurotransmitters and proteins, respectively. In this review, we summarise the different types of diamond electrodes and biosensors based on their type of detection (electrochemical or optical), functionalisation, and target analyte. The last section presents a discussion on the different analytical responses obtained with electrodes or biosensors, according to the type of analyte. Electrodes work quite well for detecting small molecules with redox properties, whereas biosensors are more suited for detecting molecules with a high molecular weight, such as DNA and proteins.

Hospitals and Laboratories on Paper-Based Sensors: A Mini Review

With characters of low cost, portability, easy disposal, and high accuracy, as well as bulky reduced laboratory equipment, paper-based sensors are getting increasing attention for reliable indoor/outdoor onsite detection with nonexpert operation. They have become powerful analysis tools in trace detection with ultra-low detection limits and extremely high accuracy, resulting in their great popularity in medical detection, environmental inspection, and other applications. Herein, we summarize and generalize the recently reported paper-based sensors based on their application for mechanics, biomolecules, food safety, and environmental inspection. Based on the biological, physical, and chemical analytes-sensitive electrical or optical signals, extensive detections of a large number of factors such as humidity, pressure, nucleic acid, protein, sugar, biomarkers, metal ions, and organic/inorganic chemical substances have been reported via paper-based sensors. Challenges faced by the current paper-based sensors from the fundamental problems and practical applications are subsequently analyzed; thus, the future directions of paper-based sensors are specified for their rapid handheld testing.

Carbon-based neural electrodes: promises and challenges

Neural electrodes are primary functional elements of neuroelectronic devices designed to record neural activity based on electrochemical signals. These electrodes may also be utilized for electrically stimulating the neural cells, such that their response can be simultaneously recorded. In addition to being medically safe, the electrode material should be electrically conductive and electrochemically stable under harsh biological environments. Mechanical flexibility and conformability, resistance to crack formation and compatibility with common microfabrication techniques are equally desirable properties. Traditionally, (noble) metals have been the preferred for neural electrode applications due to their proven biosafety and a relatively high electrical conductivity. Carbon is a recent addition to this list, which is far superior in terms of its electrochemical stability and corrosion resistance. Carbon has also enabled 3D electrode fabrication as opposed to the thin-film based 2D structures. One of carbon's peculiar aspects is its availability in a wide range of allotropes with specialized properties that render it highly versatile. These variations, however, also make it difficult to understand carbon itself as a unique material, and thus, each allotrope is often regarded independently. Some carbon types have already shown promising results in bioelectronic medicine, while many others remain potential candidates. In this topical review, we first provide a broad overview of the neuroelectronic devices and the basic requirements of an electrode material. We subsequently discuss the carbon family of materials and their properties that are useful in neural applications. Examples of devices fabricated using bulk and nano carbon materials are reviewed and critically compared. We then summarize the challenges, future prospects and next-generation carbon technology that can be helpful in the field of neural sciences. The article aims at providing a common platform to neuroscientists, electrochemists, biologists, microsystems engineers and carbon scientists to enable active and comprehensive efforts directed towards carbon-based neuroelectronic device fabrication.

Efficient Sub-1 Minute Analysis of Selected Biomarker Catecholamines by Core-Shell Hydrophilic Interaction Liquid Chromatography (HILIC) with Nanomolar Detection at a Boron-Doped Diamond (BDD) Electrode

A rapid, sensitive method for the separation of catecholamine biomarkers (CAs), of importance in traumatic brain injury (TBI) and in Parkinson’s disease (PD), has been successfully developed using hydrophilic interaction liquid chromatography (HILIC). Dopamine (DA), epinephrine (EPI), and norepinephrine (NE) are known to be three to fivefold elevated above normal in traumatic brain injury (TBI) patients. HILIC facilitates the rapid and efficient separation of these polar biomarkers, which can be poorly retained by reversed-phase liquid chromatography (RPLC), while electrochemical detection (ECD) at the boron-doped diamond (BDD) electrode provides enhanced nanomolar detection. Three HILIC columns were compared, namely the superficially porous (core-shell) Z-HILIC column and the Z-cHILIC and Z-HILIC fully porous columns. The core-shell Z-HILIC showed the highest efficiency with a rapid separation within 60 s. The HILIC method utilizing the core-shell Z-HILIC column was initially optimized for the simultaneous analysis of DA, EPI, and NE using UV detection. The advantages of using the BDD electrode over UV detection were explored, and the improved limits of detection (LODs, S/N = 3) measured were 40, 50, and 50 nM for DA, EPI, and NE, respectively. Method validation is reported in terms of the linearity, repeatability, reproducibility, and LODs. Furthermore, the proposed method was successfully applied to the real sample analysis of urinary CAs following phenylboronic acid (PBA) solid phase extraction (SPE) pretreatment.

Rice-Spikelet-like Copper Oxide Decorated with Platinum Stranded in the CNT Network for Electrochemical In Vitro Detection of Serotonin

The specific monitoring of serotonin (ST) has provoked massive interest in therapeutic and biological science since it has been recognized as the third most significant endogenous gastrointestinal neurotransmitter. Hence, there is a great need to develop a sensitive and low-cost sensing platform for the detection of a clinically relevant ST level in biological matrices. Herein, we develop a simple two-step approach for an ultrasensitive electrochemical (EC) sensor with the Cu₂O metal oxide (MO)-incorporated CNT core that has been further deposited with a transitional amount of platinum nanoparticles (Pt NPs). We presented, for the first time, the deposition of Pt NPs on the (CNTs-Cu₂O-CuO) nanopetal composite via the galvanic replacement method, where copper not only acts as a reductant but a sacrificial template as well. The electrocatalytic aptitude of the fabricated EC sensing platform has been assessed for the sensitive detection of ST as a proficient biomarker in early disease diagnostics. The synergy of improved active surface area, remarkable conductivity, polarization effect induced by Pt NPs on CNTs-Cu₂O-CuO nanopetals, fast electron transfer, and mixed-valence states of copper boost up the redox processes at the electrode-analyte junction. The CNTs-Cu₂O-CuO@Pt-modified electrode has unveiled outstanding electrocatalytic capabilities toward ST oxidation in terms of a low detection limit of 3 nM (S/N = 3), wide linear concentration range, reproducibility, and incredible durability. Owing to the amazing proficiency, the proposed EC sensor based on the CNTs-Cu₂O-CuO@Pt heterostructure has been applied for ST detection in biotic fluids and real-time tracking of ST efflux released from various cell lines as early disease diagnostic approaches.

Next-Generation Diamond Electrodes for Neurochemical Sensing: Challenges and Opportunities

Carbon-based electrodes combined with fast-scan cyclic voltammetry (FSCV) enable neurochemical sensing with high spatiotemporal resolution and sensitivity. While their attractive electrochemical and conductive properties have established a long history of use in the detection of neurotransmitters both in vitro and in vivo, carbon fiber microelectrodes (CFMEs) also have limitations in their fabrication, flexibility, and chronic stability. Diamond is a form of carbon with a more rigid bonding structure (sp3-hybridized) which can become conductive when boron-doped. Boron-doped diamond (BDD) is characterized by an extremely wide potential window, low background current, and good biocompatibility. Additionally, methods for processing and patterning diamond allow for high-throughput batch fabrication and customization of electrode arrays with unique architectures. While tradeoffs in sensitivity can undermine the advantages of BDD as a neurochemical sensor, there are numerous untapped opportunities to further improve performance, including anodic pretreatment, or optimization of the FSCV waveform, instrumentation, sp2/sp3 character, doping, surface characteristics, and signal processing. Here, we review the state-of-the-art in diamond electrodes for neurochemical sensing and discuss potential opportunities for future advancements of the technology. We highlight our team's progress with the development of an all-diamond fiber ultramicroelectrode as a novel approach to advance the performance and applications of diamond-based neurochemical sensors.

Nanomaterials Based Electrochemical Sensors for Serotonin Detection: A Review

The present review deals with the recent progress made in the field of the electrochemical detection of serotonin by means of electrochemical sensors based on various nanomaterials incorporated in the sensitive element. Due to the unique chemical and physical properties of these nanomaterials, it was possible to develop sensitive electrochemical sensors with excellent analytical performances, useful in the practice. The main electrochemical sensors used in serotonin detection are based on carbon electrodes modified with carbon nanotubes and various materials, such as benzofuran, polyalizarin red-S, poly(L-arginine), Nafion/Ni(OH)2, or graphene oxide, incorporating silver-silver selenite nanoparticles, as well as screen-printed electrodes modified with zinc oxide or aluminium oxide. Also, the review describes the nanocomposite sensors based on conductive polymers, tin oxide-tin sulphide, silver/polypyrole/copper oxide or a hybrid structure of cerium oxide-gold oxide nanofibers together with ruthenium oxide nanowires. The presentation focused on describing the sensitive materials, characterizing the sensors, the detection techniques, electroanalytical properties, validation and use of sensors in lab practice.

"Nano": An Emerging Avenue in Electrochemical Detection of Neurotransmitters

The growing importance of nanomaterials toward the detection of neurotransmitter molecules has been chronicled in this review. Neurotransmitters (NTs) are chemicals that serve as messengers in synaptic transmission and are key players in brain functions. Abnormal levels of NTs are associated with numerous psychotic and neurodegenerative diseases. Therefore, their sensitive and robust detection is of great significance in clinical diagnostics. For more than three decades, electrochemical sensors have made a mark toward clinical detection of NTs. The superiority of these electrochemical sensors lies in their ability to enable sensitive, simple, rapid, and selective determination of analyte molecules while remaining relatively inexpensive. Additionally, these sensors are capable of being integrated in robust, portable, and miniaturized devices to establish point-of-care diagnostic platforms. Nanomaterials have emerged as promising materials with significant implications for electrochemical sensing due to their inherent capability to achieve high surface coverage, superior sensitivity, and rapid response in addition to simple device architecture and miniaturization. Considering the enormous significance of the levels of NTs in biological systems and the advances in sensing ushered in with the integration of nanotechnology in electrochemistry, the analysis of NTs by employing nanomaterials as interface materials in various matrices has emerged as an active area of research. This review explores the advancements made in the field of electrochemical sensors for the sensitive and selective determination of NTs which have been described in the past two decades with a distinctive focus on extremely innovative attributes introduced by nanotechnology.

Development of an unmodified screen-printed graphene electrode for nonenzymatic histamine detection

The high requirement for food quality control has inspired the creation of high-performance sensing, cost-effectiveness, and ease to use. Therefore, the aim of this work is to develop nonenzymatic electrochemical platforms for direct detection of histamine using unmodified screen-printed graphene electrodes (SPGEs) for their applications such as evaluation of fish freshness. In alkaline media (0.2 M NaOH), unmodified SPGEs showed a very low oxidation potential of histamine at +0.58 V (vs. Ag/AgCl) avoiding perturbations from other biogenic amines. The developed method offers an excellent selectivity, sensitivity (a limit of detection (at 3SD/slope) of 0.62 mg L^-1) and wide working linear range (5-100 mg L^-1) for histamine detection. In addition, the proposed method was successfully applied to detect histamine in canned fish samples with recovery values ranging from 90.72% to 101.21%. Therefore, this newly proposed method is promising as an alternative choice for the determination of histamine in fish samples and related food products.

Electrochemical measurement of serotonin by Au-CNT electrodes fabricated on microporous cell culture membranes

Gut-brain axis (GBA) communication relies on serotonin (5-HT) signaling between the gut epithelium and the peripheral nervous system, where 5-HT release patterns from the basolateral (i.e., bottom) side of the epithelium activate nerve afferents. There have been few quantitative studies of this gut-neuron signaling due to a lack of real-time measurement tools that can access the basolateral gut epithelium. In vitro platforms allow quantitative studies of cultured gut tissue, but they mainly employ offline and endpoint assays that cannot resolve dynamic molecular-release patterns. Here, we present the modification of a microporous cell culture membrane with carbon nanotube-coated gold (Au-CNT) electrodes capable of continuous, label-free, and direct detection of 5-HT at physiological concentrations. Electrochemical characterization of single-walled carbon nanotube (SWCNT)-coated Au electrodes shows increased electroactive surface area, 5-HT specificity, sensitivity, and saturation time, which are correlated with the CNT film drop-cast volume. Two microliters of CNT films, with a 10-min saturation time, 0.6 μA/μM 5-HT sensitivity, and reliable detection within a linear range of 500 nM-10 μM 5-HT, can be targeted for high-concentration, high-time-resolution 5-HT monitoring. CNT films (12.5 μL) with a 2-h saturation time, 4.5 μA/μM 5-HT sensitivity, and quantitative detection in the linear range of 100 nM-1 μM can target low concentrations with low time resolution. These electrodes achieved continuous detection of dynamic diffusion across the porous membrane, mimicking basolateral 5-HT release from cells, and detection of cell-released 5-HT from separately cultured RIN14B cell supernatant. Electrode-integrated cell culture systems such as this can improve in vitro molecular detection mechanisms and aid in quantitative GBA signaling studies.

Comparison of electrochemical performance of various boron-doped diamond electrodes: Dopamine sensing in biomimicking media used for cell cultivation

Chemically inert and biocompatible boron-doped diamond (BDD) has been successfully used in neuroscience for sensitive neurochemicals sensing and/or as a growth substrate for neurons. In this study, several types of BDD differing in (i) fabrication route, i.e. conventional microwave plasma enhanced chemical vapour deposition (MW-PECVD) reactor vs. MW-PECVD with linear antenna delivery system, (ii) morphology, i.e. planar vs. porous BDD, and (iii) surface treatment, i.e. H-terminated (H-BDDs) vs. O-terminated (O-BDDs), were characterized from a morphological, structural, and electrochemical point of view. Further, planar and porous BDD-based electrodes were tested for sensing of dopamine in common biomimicking environments of pH 7.4, namely phosphate buffer (PB) and HEPES buffered saline (HBS). In HBS, potential windows are narrowed due to electrooxidation of its buffering component (i.e. HEPES), however, dopamine sensing in HBS is possible. H-BDDs (both planar and porous) outperformed O-BDDs as they provided clearer dopamine signals with higher peak currents. As expected, due to its enlarged surface area and increased sp² content, the highest sensitivity and lowest detection limits of 8 × 10^-8 mol L^-1 and 6 × 10^-8 mol L^-1 in PB and HBS media, respectively, were achieved by square-wave voltammetry on porous H-BDD.

Dual-recognition molecularly imprinted aptasensor based on gold nanoparticles decorated carboxylated carbon nanotubes for highly selective and sensitive determination of histamine in different matrices

In this study, an electrochemical aptamer based sensor (aptasensor) was proposed for specific recognition of histamine (HIS). The electrochemical aptasensor based on fabrication of glassy carbon electrode (GCE) with molecular imprinted polymer (MIP) and DNA aptamers on gold nanoparticles (AuNPs) and carboxylated carbon nanotubes (cCNTs) (MIP-apta/AuNPs/cCNTs/GCE). The aptasensor exhibits high selectivity towards HIS detection as it has two recognition elements which are MIP cavities and aptamer interaction. Upon exposure of MIP-apt/AuNPs/cCNTs/GCE to HIS, the current of redox probe was decreased that depends on the template (HIS) concentration. The effects of aptamer concentration, incubation time, pH and AuNPs electro-deposition time were optimized. Differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) techniques were used to analyze HIS in complicated matrices. Favorable performance of MIP-apt/AuNPs/cCNTs/GCE was achieved with linearity ranges of 0.46-35 nmol L^-1 and 0.35-35 nmol L^-1 with limits of detection (LODs, S/N = 3) of 0.15 nmol L^-1 and 0.11 nmol L^-1 using DPV and EIS, respectively. The fabricated aptasensor displayed high selectivity, desirable reproducibility and stability. The MIP-apt/AuNPs/cCNTs/GCE was used to detect HIS in human plasma and canned tuna samples with good recoveries % and RSDs %.

Synthesis of MOF-derived Ni@C materials for the electrochemical detection of histamine

Histamine (HA) plays an important role in food safety supervision and is also involved in various physiological functions. Accurate and rapid detection of HA in real sample is count for much as this is the significant prerequisite for its effective monitoring. In this study, we fabricated an electrochemical sensor to detect HA via the pyrolysis of the hydrothermal Ni-MOF (metal-organic frameworks), in which the obtained Ni@C material was deployed as the sensing agent. Ni@C was comprehensively characterized in terms of its morphology, constitution, as well as its electrochemical behavior. The as-prepared sensor (Ni@C/GCE) features excellent electrocatalytic activities. It was also observed that the electrochemical property of the sensor was substantially improved because Ni@C afforded an enlarged active surface and accelerated electron transport. This sensor affords amperometric analysis in the linear range of 10^-3-100 μM HA with a 3.2 × 10^-4 μM low detection limit (S/N = 3). Many important features, including decent anti-interference, reproducibility, stability, and reliability, were also observed. Importantly, the sensor enabled the measurement of HA in real samples obtained from fish, thus demonstrating its practical potential as a HA analytical detector.

Electrochemical detection of exogenously administered melatonin in the brain

Melatonin (MT) is an important electroactive hormone that regulates different physiological actions in the brain, ranging from circadian clock to neurodegeneration. An impressive number of publications have highlighted the effectiveness of MT treatments in different types of sleep and neurological disorders, including Alzheimer's and Parkinson's disease. The ability to detect MT in different regions of the brain would provide further insights into the physiological roles and therapeutic effects of MT. While multiple electrochemical methods have been used to detect MT in biological samples, monitoring MT in the brain of live animals has not been demonstrated. Here, we optimized a square wave voltammetry (SWV) electroanalytical method to evaluate the MT detection performance at CFEs in vitro and in vivo. SWV was able to sensitively detect the MT oxidation peak at 0.7 V, and discriminate MT from most common interferents in vitro. More importantly, using the optimized SWV, CFEs successfully detected and reliably quantified MT concentrations in the visual cortex of anesthetized mice after intraperitoneal injections of different MT doses, offering stable MT signals for up to 40 minutes. To the best of our knowledge, this is the first electrochemical measurement of exogenously administered MT in vivo. This electrochemical MT sensing technique will provide a powerful tool for further understanding MT's action in the brain.

Fabrication of Fe3O4/Au@ATP@Ag Nanorod sandwich structure for sensitive SERS quantitative detection of histamine

We have successfully prepared a highly sensitive sandwich nanosensor combined Fe₃O₄ and Au@ATP@Ag nanorods for histamine detection based on surface-enhanced Raman spectroscopy (SERS). The Fe₃O₄ beads with -COOH served as a capture part to enrich histamine. The Au@ATP@Ag core-shell nanorods functionalized with Nalpha,Nalpha-Bis(carboxymethyl)-l-lysine (AB-NTA) were then used to connect with the imidazolyl group of histamine, simultaneously the internal standard 4-aminothiophenol (4-ATP) in the core-shell structure was used as the SERS signal. PLS regression model based on concentration range 10^-3-10^-8mol/L showed a linear trend with R² = 0.9907. Our new approach can quickly and reliably determine histamine in fish sample and RAW264.7 cell lysates. This protocol for histamine extraction and SERS analysis enables the development of ultra-sensitive method for histamine detection.

Electrochemical detection of serotonin: A new approach

Serotonin (5-hydroxytryptamine, 5-HT) is an important neurotransmitter which plays a significant role in various functions in the body, such as appetite, emotions, and autonomic functions. It is well known that biomarker 5-HT levels can be correlated to several diseases and disorders such as depression, anxiety, irritable bowel, and sleep trouble. Among various methods for detecting the 5-HT biomarker, electrochemical techniques have attracted great interest due to their low cost and ease of operation. However, sensitive and precise electrochemical detection of 5-HT levels is not possible using bare electrodes, thus requiring electrode modification. The present review aims to describe the different electroanalytical methods for 5-HT detection using various surface-modified electrodes such as glassy carbon, carbon fiber, diamond, graphite, and metal electrodes modified with conductive polymers. Perspectives and the modification of electrode surface using applied polymers for 5-HT detection have also been presented.

Nanodiamond Coating Improves the Sensitivity and Antifouling Properties of Carbon Fiber Microelectrodes

Nanodiamonds (NDs) are carbon nanomaterials with a core diamond crystalline structure and crystal defects, such as graphitic carbon and heteroatoms, on their surface. For electrochemistry, NDs are promising to increase active sites and decrease fouling, but NDs have not been studied for neurotransmitter electrochemistry. Here, we optimized ND coatings on microelectrodes and found that ND increases the sensitivity for neurotransmitters with fast-scan cyclic voltammetry detection and decreases electrochemical and biofouling. Different sizes and functionalizations of NDs were tested, and ND suspensions were drop-casted onto carbon-fiber microelectrodes (CFMEs). The 5 nm ND-H and 5 nm ND-COOH formed thick coatings, while the 15 and 60 nm ND-COOH formed more sparse coatings. With electrochemical impedance spectroscopy, 5 nm ND-H and 5 nm ND-COOH had high charge-transfer resistance, while 15 and 60 nm ND-COOH had low charge-transfer resistance. ND-COOH (15 nm) was optimal, with the best electrocatalytic properties and current for dopamine. Sensitivity was enhanced 2.1 ± 0.2 times and the limit of detection for dopamine improved to 3 ± 1 nM. ND coating increased current for other cations such as serotonin, norepinephrine, and epinephrine, but not for the anion ascorbic acid. Moreover, NDs decreased electrochemical fouling from serotonin and 5-hydroxyindoleacetic acid, and they also decreased biofouling in brain slice tissue by 50%. The current at biofouled ND-coated electrodes is similar to the signal of pristine, unfouled CFMEs. The carboxylated ND-modified CFMEs are beneficial for neurotransmitter detection because of easy fabrication, improved limit of detection, and antifouling properties.

Electrochemical Detection of Dopamine and Serotonin in the Presence of Interferences in a Rotating Droplet System

In this Article, a rotating droplet system is used for simultaneous detection of dopamine and serotonin. Carbon nanoparticles functionalized with sulfonic groups on the electrode surface enables potential discrimination between the neurotransmitters and the most common interferences, whereas the efficient and low-volume hydrodynamic system helps to lower the detection limit toward physiologically relevant concentrations. Here, we present results with a 10 nM limit of detection for serotonin and a 100 nM to 2 μM linear response range from the system in a sample containing an equimolar concentrations of dopamine and serotonin and 0.5 mM concentration of both uric and ascorbic acids. Demonstrating the practical applicability of this method, we measure the concentration of serotonin in 70 μL of mice blood serum samples without additional pretreatment.

Mechanism of Histamine Oxidation and Electropolymerization at Carbon Electrodes

Histamine plays an important role in neuromodulation and the biological immune response. Although many electrochemical methods have been developed for histamine detection, the mechanism of its redox reaction has not been directly investigated. Here, we studied the mechanism of histamine oxidation at carbon electrodes and used that mechanistic information to design better fast-scan cyclic voltammetry (FSCV) methods for histamine. Using amperometry, cyclic voltammetry (CV), and X-ray photoelectron spectroscopy (XPS), we demonstrate that histamine oxidation requires a potential of at least +1.1 V vs Ag/AgCl. We propose that histamine undergoes one-electron oxidation on an imidazole nitrogen that produces a radical. The radical species dimerize and continue to undergo oxidation, leading to electropolymerization, which fouls the electrode. CV shows a peak at 1.3 V that is pH dependent, consistent with a one-proton, one-electron oxidation reaction. This mechanism is confirmed using 1- and 3-methylhistamine, which do not electropolymerize, compared to N^α-methylhistamine, which does. XPS also revealed a nitrogen-containing product adsorbed on the electrode surface after histamine oxidation. For FSCV detection of histamine at carbon-fiber microelectrodes, histamine oxidation was adsorption-controlled, and the anodic peak was observed at +1.2 V on the backward scan because of the rapid scan rate. However, the oxidation fouled the electrode and convoluted the FSCV temporal response; therefore, we implemented Nafion coating to alleviate the electrode fouling and preserve the time response of FSCV. Knowing the mechanism of histamine oxidation will facilitate design of better electrochemical methods for real-time monitoring of histamine.

Boron Doped Diamond Electrodes in Flow-Based Systems

Boron-doped diamond (BDD) electrodes present several notable properties, such as the largest potential window of all electrode materials (especially in anodic potentials), low background and capacitive currents, reduced fouling compared to other electrodes, mechanical robustness, and good stability over time. On the other hand, flow-based systems are known as well-established approaches to minimize reagent consumption and waste generation and with good compromise between sample throughput and analytical performance (mechanization of chemical assays). This review focuses on the use of BDD electrodes for electrochemical detection in flow systems, such as flow injection analysis (FIA), batch injection analysis (BIA), high performance liquid chromatography (HPLC), and capillary electrophoresis (CE). The discussion deals with the historical evolution of BDD, types of electrochemical pre-treatments (cathodically/H-terminated or anodically/O-terminated), cell configurations, and analytical performance. Articles are discussed in chronological order and subdivided according to the type of flow system: FIA, BIA, HPLC, and CE.

An electrooxidative technique to fast fabricate copper phosphate electrodes capable of integrating high performance liquid chromatography for the label-free detection of fish freshness

A simple and fast one-step electrooxidative method has been developed to monolithically produce a copper phosphate (Cu₃(PO₄)₂) compound on a disposable copper tape, which can be integrated with high performance liquid chromatography (HPLC) for the estimation of fish freshness. The Cu₃(PO₄)₂ compound of flake-like nanostructures was formed by applying a first anodic peak potential at the copper tape for 10 min in a 1 M sodium dihydrogen phosphate (NaH₂PO₄) (pH 5.0) solution. The Cu₃(PO₄)₂ electrodes can detect the oxidative reaction of histidine and histamine in 20 mM NaH₂PO₄ solutions with pH 5.0-8.5. When integrating the electrodes with a flow injection system, the linear range and the calculated detection limit of histamine were respectively 2.5-250 ppm and 0.15 ppm. The electrodes integrated to HPLC can specifically detect the histamine concentrations in fish samples in the pH 7.5 NaH₂PO₄ solution, achieving an accuracy rate of 95.3% and a recovery rate of 101.1%.

Roles of distal aspartate and arginine of B-class dye-decolorizing peroxidase in heterolytic hydrogen peroxide cleavage

Dye-decolorizing peroxidases (DyPs) represent the most recently classified hydrogen peroxide-dependent heme peroxidase family. Although widely distributed with more than 5000 annotated genes and hailed for their biotechnological potential, detailed biochemical characterization of their reaction mechanism remains limited. Here, we present the high-resolution crystal structures of WT B-class DyP from the pathogenic bacterium Klebsiella pneumoniae (KpDyP) (1.6 Å) and the variants D143A (1.3 Å), R232A (1.9 Å), and D143A/R232A (1.1 Å). We demonstrate the impact of elimination of the DyP-typical, distal residues Asp-143 and Arg-232 on (i) the spectral and redox properties, (ii) the kinetics of heterolytic cleavage of hydrogen peroxide, (iii) the formation of the low-spin cyanide complex, and (iv) the stability and reactivity of an oxoiron(IV)porphyrin π-cation radical (Compound I). Structural and functional studies reveal that the distal aspartate is responsible for deprotonation of H₂O₂ and for the poor oxidation capacity of Compound I. Elimination of the distal arginine promotes a collapse of the distal heme cavity, including blocking of one access channel and a conformational change of the catalytic aspartate. We also provide evidence of formation of an oxoiron(IV)-type Compound II in KpDyP with absorbance maxima at 418, 527, and 553 nm. In summary, a reaction mechanism of the peroxidase cycle of B-class DyPs is proposed. Our observations challenge the idea that peroxidase activity toward conventional aromatic substrates is related to the physiological roles of B-class DyPs.

Real-Time Detection of Melatonin Using Fast-Scan Cyclic Voltammetry

Melatonin is an important hormone whose functions span from regulating circadian rhythm in the brain to providing anti-inflammatory properties in the immune system. Melatonin secretion from the pineal gland is known; however, the mechanism of melatonin signaling in the immune system is not well understood. The lymph node is the hub of the immune system, and melatonin secretion from lymphocytes was proposed to be an important source specifically for regulating cytokine secretion. Methods exist to quantify the concentration of melatonin within biological samples; however, they often suffer from either a lack of selectivity for melatonin over common biological interferences or temporal resolution, which is not amenable to measuring real-time signaling dynamics. Here, we have characterized an electrochemical method for optimal melatonin detection with subsecond resolution using fast-scan cyclic voltammetry at carbon-fiber microelectrodes. The oxidation peaks detected for melatonin were at 1.0, 1.1, and 0.6 V. Evidence for electrode fouling of the tertiary peak was present; therefore, an optimized waveform was developed scanning from 0.2 to 1.3 V at 600 V/s. The optimized waveform eliminated the detection of fouling products on the electrode with a 24 ± 10 nM limit of detection. Melatonin was distinguished between biological interferences, and codetection with the major synthetic precursor, serotonin, was possible. This method was used to detect melatonin in live lymph node slices and provides the first real-time measurements within the lymph node using FSCV. Real-time detection of melatonin dynamics could provide useful information on the mechanism of immunomodulation during inflammatory disease.

A Materials Roadmap to Functional Neural Interface Design

Advancement in neurotechnologies for electrophysiology, neurochemical sensing, neuromodulation, and optogenetics are revolutionizing scientific understanding of the brain while enabling treatments, cures, and preventative measures for a variety of neurological disorders. The grand challenge in neural interface engineering is to seamlessly integrate the interface between neurobiology and engineered technology, to record from and modulate neurons over chronic timescales. However, the biological inflammatory response to implants, neural degeneration, and long-term material stability diminish the quality of interface overtime. Recent advances in functional materials have been aimed at engineering solutions for chronic neural interfaces. Yet, the development and deployment of neural interfaces designed from novel materials have introduced new challenges that have largely avoided being addressed. Many engineering efforts that solely focus on optimizing individual probe design parameters, such as softness or flexibility, downplay critical multi-dimensional interactions between different physical properties of the device that contribute to overall performance and biocompatibility. Moreover, the use of these new materials present substantial new difficulties that must be addressed before regulatory approval for use in human patients will be achievable. In this review, the interdependence of different electrode components are highlighted to demonstrate the current materials-based challenges facing the field of neural interface engineering.