Degradation of the Common Aqueous Antibiotic Tetracycline using a Carbon Nanotube Electrochemical Filter

Electric field-confined synthesis of single atomic TiOxCy electrocatalytic membranes

Electrocatalysis exhibits certain benefits for water purification, but the low performance of electrodes severely hampers its utility. Here, we report a general strategy for fabricating high-performance three-dimensional (3D) porous electrodes with ultrahigh electrochemical active surface area and single-atom catalysts from earth-abundant elements. We demonstrate a binder-free dual electrospinning-electrospraying (DESP) strategy to densely distribute single atomic Ti and titanium oxycarbide (TiOxCy) sub-3-nm clusters throughout interconnected carbon nanofibers (CNs). The composite offers ultrahigh conductivity and mechanical robustness (ultrasonication resistant). The resulting TiOxCy filtration membrane exhibits record-high water purification capability with excellent permeability (~8370 liter m-2 hour-1 bar-1), energy efficiency (e.g., >99% removal of toxins within 1.25 s at 0.022 kWh·m-3 per order), and erosion resistance. The hierarchical design of the TiOxCy membrane facilitates rapid and energy-efficient electrocatalysis through both direct electron transfer and indirect reactive oxygen species (1O2, ·OH, and O2·-, etc.) oxidations. The electric field-confined DESP strategy provides a general platform for making high-performance 3D electrodes.

MnOOH/carbon-based reactive electrochemical membrane for aqueous organic pollutants decontamination

The electrochemical filtration process (ECFP), which integrates the benefits of membrane separation with electrochemical advanced oxidation, exhibits significant potential for water decontamination. A key aspect in realizing practical applications of ECFP lies in the development of cost-effective, high-performance reactive electrochemical membranes (REM). In this work, a novel carbon-based REM (MCM-30) was prepared by coating the low-cost coal-based carbon membrane (CM) with MnOOH nano-catalyst through a simple and environmentally friendly electrochemical deposition method. Results indicated that the nano-MnOOH catalyst significantly improved the hydrophilicity and electrochemical properties of the CM, thereby enhancing its permeability and removal efficiency towards bisphenol A (BPA). The effects of deposition time, applied voltages, flow rates, electrolyte concentrations, and water matrixes on BPA removal efficiency were systematically investigated. Under optimal conditions, 30 min deposition, 2.0 V applied voltage, 2 mL min-1 flow rate, 0.1 mol L-1 Na2SO4 electrolyte concentration, the BPA removal efficiency of the MCM-30 reached to over 95%, which is much higher than that of the CM. The improved water treatment performance of MCM-30 during the electrochemical filtration could be attributed to the enhancement in both direct and indirect oxidation owing to the nano MnOOH deposition. Furthermore, the MCM-30 is recyclable and can be applied across various water backgrounds and pollutant types.

Veterinary tetracycline residues: Environmental occurrence, ecotoxicity, and degradation mechanism

Tetracycline has been widely used in the intensive livestock and poultry breeding industry to prevent and treat infectious diseases or promote animal growth. Usually, about 40.0-90.0% of tetracycline is excreted in the form of original drugs or metabolites and finally enters the surrounding water and soil, causing a series of eco-toxic effects. In this review, the toxic effects on plants, soil animals, and microorganisms are systematically reviewed. The migration and degradation mechanisms of tetracycline are emphasized, which are closely related to the physical and chemical properties of soil. In addition, the residual tetracycline in soil and water can be efficiently degraded by "plant-microorganism". Based on summarizing the current research progress, this review puts forward some important problems to be solved in the study of tetracycline residue and looks forward to the future research direction.

A Nanoconfined FeCo2O4-Embedded Ceramic Membrane Regulates Electron Transfer in Peroxymonosulfate Activation to Selectively Generate Singlet Oxygen for Water Decontamination

Peroxymonosulfate (PMS)-based advanced oxidation processes (AOPs), as a promising technology for water decontamination, are constrained by low reaction kinetics due to limited reaction selectivity and mass transfer. Herein, we designed a nanoconfined FeCo2O4-embedded ceramic membrane (FeCo2O4-CM) under flow-through pattern for PMS activation. Confining PMS and FeCo2O4 within nanochannels (3.0-4.7 nm) enhanced adsorption interactions (-7.84 eV vs -2.20 eV), thus boosting mass transfer. Nanoconfinement effect regulated electron transfer pathways from PMS to FeCo2O4-CM by modulating the active site transformation to ≡Co(III) in nanoconfined FeCo2O4-CM, enabling selectively generating 1O2. The primary role of 1O2 in the nanoconfined system was confirmed by kinetic solvent isotope experiments and indicative anthracene endoperoxide (DPAO2). The system enabled 100% removal of atrazine (ATZ) within a hydraulic retention time of 2.124 ms, demonstrating a rate constant over 5 orders of magnitude higher than the nonconfined system (3.50 × 103 s-1 vs 0.42 min-1). It also exhibited strong resilience to pH variations (3.3-9.0) and coexisting substances, demonstrating excellent stability indicated by consistent 100% ATZ removal for 14 days. This study sheds light on regulating electron transfer pathways to selectively generate 1O2 through the nanoconfinement effect, boosting the practical application of PMS-based AOPs in environmental remediation and potentially applying them to various other AOPs.

A sustainable carbon aerogel from waste paper with exceptional performance for antibiotics removal from water

In this work, a sustainable 3D carbon aerogel (AO-WPC) is prepared from waste paper (WP), and used for efficient antibiotics removal from water. The AO-WPC aerogel shows good mechanical property and can recover after 100th of 30 % compression strain. The specific surface area of AO-WPC aerogel is up to 654.58 m2/g. More importantly, this aerogel reveals proper pore size distribution, including micro sized macropores between carbon fibers and intrinsic nano scale mesopores (11.86 nm), which is conducive to remove antibiotics from water. Taking tetracycline (Tc) as an example, the maximum adsorption capacity and adsorption rate of AO-WPC for Tc are as high as 384.6 mg/g and 0.510 g/(mg‧min), respectively, which exhibits significant advantages over most of the recent absorbents, and the adsorption toward Tc reveals good resistance to various environmental factors, including pH, various ions, and dissolved organic matter (DOM). Moreover, good thermal stability enables the AO-WPC aerogel to be regenerated through simple burning, and the adsorption capacity of Tc only decreases by 10.4 % after 10 cycles. Mechanism research shows that hydrogen bonding and π-π electron-donor-acceptor (EDA) interaction play the important role in the adsorption. The excellent mechanical property and adsorption performance imply good practical prospect of the AO-WPC aerogel.

Removal of 6-methylquinoline from shale gas wastewater using electrochemical carbon nanotubes filter

6-Methylquinoline (6-MQ) is identified as a high-concentration organic compound pervasive in shale gas wastewater (SGW) and poses a significant risk of environmental pollution. In response, this study aimed to address these challenges by introducing an innovative electrochemical membrane constructed with multi-walled carbon nanotubes (CNTs) for the removal of 6-MQ. The investigation systematically explored the impact of voltage, initial pollutant concentration, and salinity on the performance of the electrochemical CNTs filter. It was found a positive correlation between removal efficiency and increasing voltage and salinity levels. Conversely, as the initial concentration of pollutants increased, the efficiency showed a diminishing trend. The electrochemical CNTs filter exhibited remarkable efficacy in both adsorption removal and electrochemical oxidation of 6-MQ. Notably, the CNTs membrane exhibited robust adsorption capabilities, evidenced by the sustained adsorption of 6-MQ for over 33 h. Furthermore, applying an electrochemical oxidation voltage of 3 V consistently maintained a removal rate exceeding 34.0% due to both direct and indirect oxidation, underscoring the sustained efficacy of the electrochemical membranes. Besides, real wastewater experiments, while displaying a reduction in removal efficiency compared to synthetic wastewater experiments, emphasized the substantial potential of the electrochemical CNTs filter for practical applications. This study underscores the significant promise of electrochemical membranes in addressing low molecular weight contaminants in SGW, contributing valuable insights for advancing SGW treatment strategies.

Electrochemical filtration for drinking water purification: A review on membrane materials, mechanisms and roles

Electrochemical filtration can not only enrich low concentrations of pollutants but also produce reactive oxygen species to interact with toxic pollutants with the assistance of a power supply, making it an effective strategy for drinking water purification. In addition, the application of electrochemical filtration facilitates the reduction of pretreatment procedures and the use of chemicals, which has outstanding potential for maximizing process simplicity and reducing operating costs, enabling the production of safe drinking water in smaller installations. In recent years, the research on electrochemical filtration has gradually increased, but there has been a lack of attention on its application in the removal of low concentrations of pollutants from low conductivity water. In this review, membrane substrates and electrocatalysts used to improve the performance of electrochemical membranes are briefly summarized. Meanwhile, the application prospects of emerging single-atom catalysts in electrochemical filtration are also presented. Thereafter, several electrochemical advanced oxidation processes coupled with membrane filtration are described, and the related working mechanisms and their advantages and shortcomings used in drinking water purification are illustrated. Finally, the roles of electrochemical filtration in drinking water purification are presented, and the main problems and future perspectives of electrochemical filtration in the removal of low concentration pollutants are discussed.

Sustainable production of Fe-doped MnO2 nanoparticles for accelerated tetracycline antibiotic detoxification

Manganese dioxide (MnO2) has been recognized as one of the natural systems' most active mineral oxidants. However, when it comes to catalytic oxidation of antibiotic applications, pure MnO2 falls short in delivering satisfactory performance. Hence, a set of Fe3+-doped porous MnO2 (0.02Fe-MnO2, 0.1Fe-MnO2, and 0.14Fe-MnO2) nanoparticles were synthesized here via a convenient and energy-efficient one-step reaction method. A series of experiments revealed that Fe-doping strategy enhances the properties of MnO2 host by suppressing the crystalline structure, increasing the amount of surface oxygen defects, and modifying the Mn3+/Mn4+ ratio. Specifically, the tetracycline (TC) removal efficiency of 0.14Fe-MnO2 reaches 92% without the need for any additional co-oxidant, representing a 20% improvement over pristine MnO2 nanoparticles. Moreover, this process shows a fast dynamic (achieving 70% of TC removal in just 5 min) and demonstrates pH-resistance, maintaining high TC removal efficiency (≥90%) over a wide pH range of 3.0-9.0. Mechanical studies reveal that the degradation of TC can be attributed to the oxidation by reactive oxygen radicals and Mn3+, with 1O2 being the primary radical involved in the reaction, accounting for 55% of TC removal. Importantly, cytotoxicity testing indicates that the biotoxicity of TC toward organisms can be effectively mitigated using 0.14Fe-MnO2 nanomaterial. This study presents a readily applicable candidate for economically and conveniently eliminating of environmental TC pollution, thereby reducing the threat posed by TC pollution to the ecosystem.

Impact of Polythiophene ((C4H4S)n; n = 3, 5, 7, 9) Units on the Adsorption, Reactivity, and Photodegradation Mechanism of Tetracycline by Ti-Doped Graphene/Boron Nitride (Ti@GP_BN) Nanocomposite Materials: Insights from Computational Study

This study addresses the formidable persistence of tetracycline (TC) in the environment and its adverse impact on soil, water, and microbial ecosystems. To combat this issue, an innovative approach by varying polythiophene ((C4H4S)n; n = 3, 5, 7, 9) units and the subsequent interaction with Ti-doped graphene/boron nitride (Ti@GP_BN) nanocomposites was applied as catalysts for investigating the molecular structure, adsorption, excitation analysis, and photodegradation mechanism of tetracycline within the framework of density functional theory (DFT) at the B3LYP-gd3bj/def2svp method. This study reveals a compelling correlation between the adsorption potential of the nanocomposites and their corresponding excitation behaviors, particularly notable in the fifth and seventh units of the polythiophene configuration. These units exhibit distinct excitation patterns, characterized by energy levels of 1.3406 and 924.81 nm wavelengths for the fifth unit and 1.3391 and 925.88 nm wavelengths for the seventh unit. Through exploring deeper, the examination of the exciton binding energy emerges as a pivotal factor, bolstering the outcomes derived from both UV-vis transition analysis and adsorption exploration. Notably, the calculated exciton binding energies of 0.120 and 0.103 eV for polythiophene units containing 5 and 7 segments, respectively, provide compelling confirmation of our findings. This convergence of data reinforces the integrity of our earlier analyses, enhancing our understanding of the intricate electronic and energetic interplay within these intricate systems. This study sheds light on the promising potential of the polythiophene/Ti-doped graphene/boron nitride nanocomposite as an efficient candidate for TC photodegradation, contributing to the advancement of sustainable environmental remediation strategies. This study was conducted theoretically; hence, experimental studies are needed to authenticate the use of the studied nanocomposites for degrading TC.

Packed OV-SnO2-Sb bead-electrodes for enhanced electrocatalytic oxidation of micropollutants in water

Electrocatalytic oxidation is an appealing treatment option for emerging micropollutants in wastewater, however, the limited reactive surface area and short service lifetime of planar electrodes hinder their industrial applications. This study introduces an innovative electrochemical wastewater treatment technology that employs packed bead-electrodes (PBE) as a dynamic electrocatalytic filter on a dimensionally stable anode (DSA) acting as a current collector. By using PBE, the electroactive volume is expanded beyond the vicinity of the common planar anode to the thick porous media of PBE with a vast electrocatalytic surface area. This greatly enhances the efficiency of electrochemical degradation of micropollutants. The OV-SnO2-Sb PBE filter achieved a nearly 100 % degradation of moxifloxacin (MOX) in under 2 min of single-pass filtration, with a degradation rate over an order of magnitude higher than the conventional electrochemical oxidation processes. The generation of abundant radical species (•OH) and non-radical species (1O2 and O3), along with the enhanced direct oxidation, led to the outstanding performance of the charged PBE system in MOX degradation. The OV-SnO2-Sb PBE was remarkably stable, and the separation between the electroactive PBE layer and the base Ti anode allows for easy renewal of the bead-electrode materials and scaling up of the system for practical applications. Overall, our study presents a dynamic electroactive PBE that advances the electrocatalytic oxidation technology for effective control of emerging pollutants in the water environment. This technology has the potential to revolutionize electrochemical wastewater treatment and contribute to a more sustainable future environment.

Electrochemical reduction of wastewater by non-noble metal cathodes: From terminal purification to upcycling recovery

A shift beyond conventional environmental remediation to a sustainable pollutant upgrading conversion is extremely desirable due to the rising demand for resources and widespread chemical contamination. Electrochemical reduction processes (ERPs) have drawn considerable attention in recent years in the fields of oxyanion reduction, metal recovery, detoxification and high-value conversion of halogenated organics and benzenes. ERPs also have the potential to address the inherent limitations of conventional chemical reduction technologies in terms of hydrogen and noble metal requirements. Fundamentally, mechanisms of ERPs can be categorized into three main pathways: direct electron transfer, atomic hydrogen mediation, and electrode redox pairs. Furthermore, this review consolidates state-of-the-art non-noble metal cathodes and their performance comparable to noble metals (e.g., Pd, Pt) in electrochemical reduction of inorganic/organic pollutants. To overview the research trends of ERPs, we innovatively sort out the relationship between the electrochemical reduction rate, the charge of the pollutant, and the number of electron transfers based on the statistical analysis. And we propose potential countermeasures of pulsed electrocatalysis and flow mode enhancement for the bottlenecks in electron injection and mass transfer for electronegative pollutant reduction. We conclude by discussing the gaps in the scientific and engineering level of ERPs, and envisage that ERPs can be a low-carbon pathway for industrial wastewater detoxification and valorization.

Degradation of tetracycline by peroxymonosulfate activated with Mn0.85Fe2.15O4-CNTs: Key role of singlet oxygen

Tetracycline (TC) is a kind of electron-rich organic, and singlet oxygen (¹O₂) oxidative pathway-based advanced oxidation processes (AOPs) have represented outstanding selective degradation to such pollutants. In this paper, an excellent prepared strategy for ¹O₂ dominated catalyst was adopted. A catalyst composed of non-stoichiometric doping Mn-Fe bimetallic oxide supported on CNTs (0.3-Mn_0.85Fe_2.15O₄-CNTs) was synthesized and optimized by regulating the non-stoichiometric doping ratio of Mn & Fe and the loading amount of CNTs. Through optimization and control experiments, the optimized catalyst represented 94.9% of TC removal efficiency within 60 min in neutral condition under relatively low concentrations of Mn_0.85Fe_2.15O₄-CNTs (0.4 g/L) and PMS (0.8 mM). Through SEM and XRD characterization, Mn_0.85Fe_2.15O₄-CNTs was a hybrid of cubic Mn_0.85Fe_2.15O₄ uniformly dispersing on CNTs. By the characterization of XPS and FT-IR, more CO bonds and low-valent Mn (II) & Fe (II) appeared in Mn_0.85Fe_2.15O₄-CNTs. Reactive oxygen species (ROS) was determined by radical quenching experiments and electron spin resonance (EPR) spectroscopy, and ¹O₂ was verified to be the dominated ROS. The mechanism for PMS' activation was speculated, and more low-valent Mn (II) and Fe (II) contributed to the production of free-radical (•OH & SO₄^•-), while the reaction between PMS and the enhanced CO bond on Mn_0.85Fe_2.15O₄-CNTs played a crucial part in the generation of ¹O₂. In addition, through the comparative degradation of four different organics with distinct charge densities, the excellent selectivity of ¹O₂-based oxidative pathway to electron-rich pollutants was found. This paper supplied a good strategy to prepare catalyst for PMS activation to form a ¹O₂-dominated oxidative pathway.

The enhance mechanism of DOM on tetracyclines degradation by electrochemical technology: A improvement of treatment processes

Tetracyclines (TC) is a typical broad-spectrum antimicrobial agent, and excessive use of TC can lead to a large accumulation of residual tetracycline in water. DOM is organic substances that can pass through the 0.45 μm filter. While dissolved organic matter (DOM) is one of the most significant substances in water, which has an important effect on water treatment. In this study, ultraviolet and visible spectrophotometry (UV-Vis) is applied to explore DOM to the effect of the electrochemical degradation. Three-dimension excitation emission matrix fluorescence spectroscopy (3D-EEM) is used to identify the component variation of DOM after the electrochemical oxidation (EO). Liquid chromatograph mass spectrometer (LC-MS) is used to confirm the degradation pathway of TC whether spontaneous or electrochemical oxidation. High performance liquid chromatography (HPLC) suggests the ROS production by DOM in the electrochemical oxidation under different conditions. Results show that DOM can promote the degradation of TC in the electrochemical oxidation. Tailwater DOM containssubstances can produce persistent free radicals, which can promote the degradation under light and dark conditions, natural source DOM can produce more free radicals under light. Therefore, TC wastewater should be added tailwater to promote the degradation of TC before the further water treatment. Otherwise, TC can be degraded to differentpathways (light, electricity, and degrade spontaneously). This study provides a significant idea for practical water treatment of tetracyclines, and promotes the practical application of electrochemical technology.

Electroactive membrane with the electroactive layer beneath the separation layer to eliminate the interference of humic acid in the oxidation of antibiotics

Removing harmful antibiotics is essential to reclaiming water from municipal secondary effluent. Electroactive membranes are effective in the removal of antibiotics but challenged by the abundant coexisting macromolecular organic pollutants in municipal secondary effluent. To eliminate the interference of macromolecular organic pollutants in the removal of antibiotics, we propose a novel electroactive membrane with a top polyacrylonitrile (PAN) ultrafiltration layer and a bottom electroactive layer composed of carbon nanotubes (CNTs) and polyaniline (PANi). When filtering the mixture of tetracycline (TC, a typical antibiotic) and humic acid (HA, a typical macromolecular organic pollutant), the PAN-CNT/PANi membrane performed sequential removal. It retained HA at the PAN layer (by ∼96%) and allowed TC to reach the electroactive layer where it was electrochemically oxidized (e.g., by ∼92% at 1.5 V). The TC removal of the PAN-CNT/PANi membrane was marginally affected by HA, unlike that of the control membrane with the electroactive layer on the top that showed decreased TC removal after the addition of HA (e.g., decreased by 13.2% at 1 V). The decreased TC removal of the control membrane was attributed to the attachment (but not competitive oxidation) of HA on the electroactive layer that impaired the electrochemical reactivity. The HA removal prior to TC degradation realized by the PAN-CNT/PANi membrane avoided the attachment of HA and guaranteed TC removal on the electroactive layer. Long-term filtration for 9 h revealed the stability of the PAN-CNT/PANi membrane, and its advantageous structural design was conformed in the context of real secondary effluents.

Coupling anodic and cathodic reactions using an electrocatalytic dual-membrane system actuates ultra-efficient degradation with regulable mechanisms

The versatile reaction possibilities arising from the interaction between the anodic and cathodic reactions naturally contained in electrocatalytic membrane filtration (EMF) systems are of great valuable in meeting the current complex water treatment requirements. But currently, most studies only focus on half-cell reactions with a single electrocatalytic membrane, which limits the research progress of the EMF technology. Here we report a coupling strategy that utilizes the interaction between the anodic and cathodic reactions to actuate ultra-efficient degradation performance with regulable reaction mechanisms. An electrocatalytic dual-membrane filtration (EDMF) system was established. Six typical configurations of the EDMF system were set up and systematically investigated by adjusting the electrode distance and filtration sequence. Based on the obtained results of degradation performance and mechanisms, a regulation strategy which enabled flexible tuning of direct nonradical oxidation (e.g., h⁺) and indirect oxidation (e.g., ¹O₂, ·OH, HO₂·, O₂·^-, etc.) was proposed. In particular, cathodic reactions were found to adversely affect the anodic reactions at the relatively short electrode distance of 0.9 mm. Anodic reactions could inhibit the generation of ¹O₂ at short distance of 0.9 mm but promote its generation at long distances of 9 and 17 mm. The A-C_0.9 configuration achieved the highest degradation performance, while the C-A_9 configuration was revealed to be much more conducive to ¹O₂ production. Overall, our findings demonstrate the versatility and tunability of the reaction mechanism and performance of the EDMF system due to the flexible coupling of the anodic and cathodic reactions, which potentially lays a foundation for future development of ultra-efficient mechanism-adjustable electrocatalysis technologies.

Subtle tuning of nanodefects actuates highly efficient electrocatalytic oxidation

Achieving controllable fine-tuning of defects in catalysts at the atomic level has become a zealous pursuit in catalysis-related fields. However, the generation of defects is quite random, and their flexible manipulation lacks theoretical basis. Herein, we present a facile and highly controllable thermal tuning strategy that enables fine control of nanodefects via subtle manipulation of atomic/lattice arrangements in electrocatalysts. Such thermal tuning endows common carbon materials with record high efficiency in electrocatalytic degradation of pollutants. Systematic characterization and calculations demonstrate that an optimal thermal tuning can bring about enhanced electrocatalytic efficiency by manipulating the N-centered annulation-volatilization reactions and C-based sp³/sp² configuration alteration. Benefiting from this tuning strategy, the optimized electrocatalytic anodic membrane successfully achieves >99% pollutant (propranolol) degradation during a flow-through (~2.5 s for contact time), high-flux (424.5 L m^-2 h^-1), and long-term (>720 min) electrocatalytic filtration test at a very low energy consumption (0.029 ± 0.010 kWh m^-3 order^-1). Our findings highlight a controllable preparation approach of catalysts while also elucidating the molecular level mechanisms involved.

Environment-friendly and efficient electrochemical degradation of sulfamethoxazole using reduced TiO2 nanotube arrays-based Ti membrane coated with Sb-SnO2

This study focused on the preparation, characterization, and sulfamethoxazole (SMX) removal performance of the SnO₂-coated reactive electrochemical membrane (REM). This REM was fabricated by loading SnO₂ on the reduced TiO₂ nanotube arrays (RTNA)-based Ti membrane (TM). Regarding the dopant for SnO₂, Sb was more effective in boosting the electrocatalytic activity than Bi, and the energy consumption for Sb-SnO₂-coated REM (TM/RTNA/ATO) was lower than Bi-SnO₂-coated REM (TM/RTNA/BTO). As for the internal layer, RTNA provided TM/RTNA/ATO with more electroactive surface areas and prolonged the service lifetime. Compared with batch mode, the SMX removal efficiency in flow-through mode was increased up to 8.4-fold. The SMX degradation performances were also affected by fluid velocity, current density, initial SMX concentration, and electrolyte concentration. The synergistic effects of ^•OH oxidation and direct electron transfer were responsible for the effective removal of SMX. TM/RTNA/ATO was proved to be stable and durable by multi-cycle and accelerated lifetime tests. Its extensive applicability was verified with high removal efficiencies of SMX in the surface water and wastewater effluent. These results demonstrate the promise of TM/RTNA/ATO for water treatment applications.

Carbon electrochemical membrane functionalized with flower cluster-like FeOOH catalyst for organic pollutants decontamination

Decorating active catalysts on the reactive electrochemical membrane (REM) is an effective way to further improve its decontamination performance. In this work, a novel carbon electrochemical membrane (FCM-30) was prepared through coating FeOOH nano catalyst on a low-cost coal-based carbon membrane (CM) through facile and green electrochemical deposition. Structural characterizations demonstrated that the FeOOH catalyst was successfully coated on CM, and it grew into a flower cluster-like morphology with abundant active sites when the deposition time was 30 min. The nano FeOOH flower clusters can obviously boost the hydrophilicity and electrochemical performance of FCM-30, which enhance its permeability and bisphenol A (BPA) removal efficiency during the electrochemical treatment. Effects of applied voltages, flow rates, electrolyte concentrations and water matrixes on BPA removal efficiency were investigated systematically. Under the operation condition of 2.0 V applied voltage and 2.0 mL·min^-1 flow rate, FCM-30 can achieve the high removal efficiency of 93.24% and 82.71% for BPA and chemical oxygen demand (COD) (71.01% and 54.89% for CM), respectively, with only a low energy consumption (EC) of 0.41 kWh·kgCOD^-1, which can be ascribed to the enhancement on OH yield and direct oxidation ability by the FeOOH catalyst. Moreover, this treatment system also exhibits good reusability and can be adopted on different water background as well as different pollutants.

Lightning-Rod Effect on Nanowire Tips Reinforces Electroporation and Electrochemical Oxidation: An Efficient Strategy for Eliminating Intracellular Antibiotic Resistance Genes

Conventional oxidative disinfection methods are usually inefficient to eliminate intracellular antibiotic resistance genes (i-ARGs) due to competitive oxidation of cellular components of antibiotic-resistant bacteria (ARB), resulting in the ubiquitous occurrence of ARGs in drinking water systems. Herein, we developed the strategy of coupling electroporation and electrochemical oxidation on a Co₃O₄-nanowires-modified electrode to destroy the multiresistant Escherichia coli cells and promote subsequent i-ARG (bla_TEM-1 and aac(3)-II) degradation. The lightning-rod effect over nanowire tips can form finite regions with a locally enhanced electric field and highly concentrated charge density, in turn facilitating the electroporation for ARB cell damage and electrochemical reactivity for reactive chlorine/oxygen species generation. Characterization of the ARB membrane integrity and morphology revealed that electroporation-induced cell pores were further enlarged by the oxidation of reactive species, resulting in i-ARG removal at lower applied voltages and with 6-9 times lower energy consumption than the conventional electrochemical oxidation approach with a Co₃O₄-film-modified electrode. The satisfactory application and effective inhibition of horizontal gene transfer in tap water further demonstrated the great potential of our strategy in the control of the ARG dissemination risk in drinking water systems.

Step scheme nickel-aluminium layered double hydroxides/biochar heterostructure photocatalyst for synergistic adsorption and photodegradation of tetracycline

Improving the adsorption ability of layered double hydroxide (LDH) has been considered as a promising strategy to promote its photodegradation of aqueous pollutants. In this work, nickel-aluminium layered double hydroxides (NiAl-LDH)/biochar nanocomposites were prepared using a simple coprecipitation method, and then applied in synergistic adsorption-photodegradation of tetracycline (TC) in aqueous solutions. In addition, the governing TC removal mechanisms by the nanocomposites were revealed. All NiAl-LDH/BC samples showed strong adsorption and photodegradation of TC. The Langmuir maximum TC adsorption capacity of optimized NiAl-LDH/BC-0.5 reached 124.2 mg/g, which was much better than that of NiAl-LDH (56.1 mg/g) and biochar (11.1 mg/g). Besides, TC photodegradation rate constant of NiAl/BC-0.5 was 3.6 and 4.4 times of that of NiAl-LDH and BC, respectively. The NiAl/BC-0.5 exhibited the maximum TC adsorption-photodegradation efficiency 94.4% in 90 min compared to NiAl-LDH (73.7%) and BC (48.2%). The rate constant of modified Elovich kinetic model for synergistic adsorption and photodegradation on NiAl/BC-0.5 (9.477 min^-1) was the highest among the composites. The NiAl-LDH/BC had significantly larger BET surface areas than NiAl-LDH and BC. The step scheme (S-scheme) heterostructures were constructed on the interface of BC and NiAl-LDH in nanocomposites, which facilitated the transfer of photo-induced charges. This work demonstrates that combination of NiAl-LDH and biochar can create synergy for TC adsorption-photodegradation, which is a promising and green strategy.

Self-Assembly 2D Ti3C2/g-C3N4 MXene Heterojunction for Highly Efficient Photocatalytic Degradation of Tetracycline in Visible Wavelength Range

An ultrathin 2D Ti₃C₂/g-C₃N₄ MXene (2D-TC/CN) heterojunction was synthesized, using a facile self-assembly method; the perfect microscopic-morphology and the lattice structure presented in the sample with a 2 wt% content of Ti₃C₂ were observed by the field-emission scanning electron microscopy (SEM) and transmission electron microscope (TEM). The optimized sample (2-TC/CN) exhibited excellent performance in degrading the tetracycline (TC), and the degradation rate reached 93.93% in the conditions of 20 mg/L, 50 mL of tetracycline within 60 min. Except for the increased specific-surface area, investigated by UV-vis diffuse reflectance spectra (UV-vis DRS) and X-ray photoelectron microscopy (XPS) valence spectra, the significantly enhanced photocatalytic activity of the 2-TC/CN could also be ascribed to the formation of Ti-N bonds between Ti₃C₂ and g-C₃N₄ nanosheets, which reduced the width of the band gap through adjusting the position of the valence band, thus resulting in the broadened light-absorption. Furthermore, the facilitated electron transmission was also proved by time-resolved photoluminescence (TRPL) and electrochemical impedance spectroscopy (EIS), which is effective in improving the quantum efficiency of photo-generated electrons. In addition, the resulting radical-capture experiment suggested that superoxide radicals have the greatest influence on photodegradation performance, with the photodegradation rate of TC reducing from 93.16% to 32.08% after the capture of superoxide radicals, which can be attributed to the production of superoxide radicals only, by the 2-TC/CN composites with a high conduction-band value (-0.62 eV). These facilely designed 2D Ti₃C₂/g-C₃N₄ composites possess great application potential for the photodegradation of tetracycline and other antibiotics.

Bio-electrocatalytic degradation of tetracycline by stainless-steel mesh based molybdenum carbide electrode

In order to treat antibiotic wastewater with high efficiency and low energy consumption, this study proposed the coupling of electrocatalytic degradation and biodegradation, and explored a new modified electrocatalytic material in the coupling system. The stainless-steel mesh based molybdenum carbide (SS-Mo₂C) was prepared by a low-cost impregnation method and showed superior electrocatalytic degradation ability for tetracycline (TC) when used as the anode in the electrocatalytic system. The degradation rate of TC with SS-Mo₂C anode was 17 times higher than that of stainless-steel (SS) anode, and TC removal efficiency was 77% higher than that of SS anode. The electrocatalytic system prior to the biological reactor was proven to be the optimal coupling method. The external coupling system achieved a significantly higher TC removal (87.0%) than that of the internal coupling system (65.3%) and SS-Mo₂C showed an excellent repeatable and stable performance. The fewer and smaller molecular weight intermediates products were observed in bio-electrocatalytic system, especially in the external coupling system. Alpha diversity analysis further confirmed that bio-electrocatalytic system increased the diversity of the microbial community. The stainless-steel mesh based molybdenum carbide (SS-Mo₂C), which was prepared by a simple and low-cost impregnation method, significantly improved the electrocatalytic activity of anode, thus contributing to tetracycline removal in the bio-electrocatalytic system, especially in the external coupling system.

Electroactive Ultrafiltration Membrane for Simultaneous Removal of Antibiotic, Antibiotic Resistant Bacteria, and Antibiotic Resistance Genes from Wastewater Effluent

To combat the spread of antibiotic resistance into the environment, we should adequately manage wastewater effluent treatment to achieve simultaneous removal of antibiotics, antibiotic resistant bacteria (ARB), and antibiotic resistance genes (ARGs). Herein, we fabricate a multifunctional electroactive poly(vinylidene fluoride) ultrafiltration membrane (C/PVDF) by phase inversion on conductive carbon cloth. The membrane possesses not only excellent retention toward ARB and ARGs but also exhibits high oxidation capacity as an electrode. Notably, sulfamethoxazole degradation involving hydroxylation and hydrolysis by the anode membrane is predominant, and the degradation efficiency is up to 81.5% at +4 V. Both electro-filtration processes exhibit significant ARB inactivation, anode filtration is superior to cathode filtration. Moreover, the degradation of intracellular ARGs (iARGs) located in the genome is more efficient than those located in the plasmid, and these degradation efficiencies at -2 V are higher than +2 V. The degradation efficiencies of extracellular ARGs (eARGs) are opposite and are lower than iARGs. Compared with regular filtration, the normalized flux of electroactive ultrafiltration membrane is improved by 18.0% at -2 V, 15.9% at +2 V, and 30.4% at +4 V during treating wastewater effluent, confirming its antifouling properties and feasibility for practical application.

Ganzoury M, Zhang N, de Lannoy CF. Nanocomposite Polymeric Membranes for Organic Micropollutant Removal: A Critical Review

The prevalence of organic micropollutants (OMPs) and their persistence in water supplies have raised serious concerns for drinking water safety and public health. Conventional water treatment technologies, including adsorption and biological treatment, are known to be insufficient in treating OMPs and have demonstrated poor selectivity toward a wide range of OMPs. Pressure-driven membrane filtration has the potential to remove many OMPs detected in water with high selectivity as a membrane's molecular weight cutoff (MWCO), surface charge, and hydrophilicity can be easily tailored to a targeted OMP's size, charge and octanol-water partition coefficient (Kow). Over the past 10 years, polymeric (nano)composite microfiltration (MF), ultrafiltration (UF), and nanofiltration (NF) membranes have been extensively synthesized and studied for their ability to remove OMPs. This review discusses the fate and transport of emerging OMPs in water, an assessment of conventional membrane-based technologies (NF, reverse osmosis (RO), forward osmosis (FO), membrane distillation (MD) and UF membrane-based hybrid processes) for their removal, and a comparison to the state-of-the-art nanoenabled membranes with enhanced selectivity toward specific OMPs in water. Nanoenabled membranes for OMP treatment are further discussed with respect to their permeabilities, enhanced properties, limitations, and future improvements.

Oxygen-vacancy-enriched substrate-less SnOx/La-Sb anode for high-performance electrocatalytic oxidation of antibiotics in wastewater

Electrocatalytic oxidation is a promising technology for treating toxic organic pollutants in water and wastewater, but conventional Ti-based anodes often exhibit a short service life and low efficiency in application. Oxygen vacancy (O_V)-based defect engineering is an effective activation method for enhancing the electrocatalytic activity of electrodes. Herein, the controllable formation of O_V on the surface of a freestanding SnO₂-Sb anode was achieved by the quantitative doping of La³⁺ into the SnO₂ crystal structure of the anode for high-performance electrochemical wastewater treatment. The resultant SnO_x/La-Sb anode degraded nearly 100% moxifloxacin (MOX, 10 mg L^-1) in 30 min, with a low energy consumption of 0.09 kWh m^-3. The SnO_x/La-Sb anode with an O_V density of 1.09% had the highest degradation rate constant (0.226 min^-1), 8 times higher than that of the SnO₂-Sb anode and 16 times higher than that of the state-of-the-art boron-doped diamond anode. La³⁺ doping-induced O_V activated the anode surface for electrochemical reactions by boosting the interfacial electron transfer and •OH generation (103% increase). The novel 3D permeable SnO_x/La-Sb anode also exhibited remarkable stability (predicted service life of 59 years) and high-rate performance (>98%) in a continuous flow-through treatment system (<1 min through the anode).

Biofouling suppresses effluent toxicity in an electrochemical filtration system for remediation of sulfanilic acid-contaminated water

Electrochemical filtration system (EFS) has received broad interest due to its high efficiency for organic contaminants removal. However, the porous nature of electrodes and flow-through operation mode make it susceptible to potential fouling. In this work, we systematically investigated the impacts of biofouling on sulfanilic acid (SA) removal and effluent toxicity in an EFS. Results showed that the degradation efficiency of SA slightly deteriorated from 92.3% to 81.1% at 4.0 V due to the electrode fouling. Surprisingly, after the occurrence of fouling, the toxicity (in terms of luminescent bacteria inhibition) of the EFS effluent decreased from 72.3% to 40.2%, and cytotoxicity assay exhibited similar tendency. Scanning electron microscopy and confocal laser scanning microscopy analyses revealed that biofouling occurred on the porous cathode, and live microorganisms were the dominant contributors, which are expected to play an important role in toxicity suppression. The relative abundance of Flavobacterium genus, related to the degradation of p-nitrophenol (an aromatic intermediate product of SA), increased on the membrane cathode after fouling. The analysis of degradation pathway confirmed the synergetic effects of electrochemical oxidation and biodegradation in removal of SA and its intermediate products in a bio-fouled EFS, accounting for the decrease of the effluent toxicity. Results of our study, for the first time, highlight the critical role of biofouling in detoxication using EFS for the treatment of contaminated water.

Electrochemical degradation of antibiotics using flow-through graphene sponge electrodes

Graphene sponge electrodes doped with atomic boron and nitrogen were employed for electrochemical degradation of antibiotics sulfamethoxazole, trimethoprim, ofloxacin, and erythromycin. The removal of antibiotics that displayed strong π-π interactions (i.e., ofloxacin) with reduced graphene oxide (RGO) coating was less limited by the mass transfer and removal efficiencies > 80% were observed for the investigated range of electrolyte flowrates. At the highest applied flowrate (700 LMH), increase in the anodic current significantly worsened the removal of trimethoprim and erythromycin due to the detrimental impact of the evolving gas bubbles. Increase in current at 700 LMH led to a stepwise increase in the removal efficiency of sulfamethoxazole due to its enhanced electrosorption. Electrochemical degradation was achieved via ozone, hydrogen peroxide and hydroxyl radical (^•OH). Extraction of the employed graphene sponges confirmed the degradation of the strongly adsorbing antibiotics. Identified electrochemical transformation products of erythromycin confirmed the participation of ^•OH, through N-demethylation of the dimethylamine group. In real tap water, removal efficiencies were lower for all target antibiotics. Lower electric conductivity of tap water and thus increased thickness of the electric double layer likely limited their interaction with the graphene sponge surface, in addition to the presence of low amounts of organic matter.

Recent advances in electrocatalytic membrane for the removal of micropollutants from water and wastewater

The increasing occurrence of micropollutants in water and wastewater threatens human health and ecological security. Electrocatalytic membrane (EM), a new hybrid water treatment platform that integrates membrane separation with electrochemical technologies, has attracted extensive attention in the removal of micropollutants from water and wastewater in the past decade. Here, we systematically review the recent advances of EM for micropollutant removal from water and wastewater. The mechanisms of the EM for micropollutant removal are first introduced. Afterwards, the related membrane materials and operating conditions of the EM are summarized and analyzed. Lastly, the challenges and future prospects of the EM in research and applications are also discussed, aiming at a more efficient removal of micropollutants from water and wastewater.

Promotion of Phenol Electro-oxidation by Oxygen Evolution Reaction on an Active Electrode for Efficient Pollution Control and Hydrogen Evolution

We report an electrolysis system using NiFe layered double hydroxide/CoMoO₄/nickel foam (NFLDH/CMO/NF) as the anode and CMO/NF as the cathode for simultaneous phenol electro-oxidation and water electrolysis. This system shows high performance for both phenol degradation and hydrogen evolution. We demonstrate that the degradation rate of phenol on the active anode is governed by the mass transfer rate at a low phenol concentration (0.5-2 mM) and by the electro-oxidation rate at a high phenol concentration (5 mM). The anodic oxygen evolution reaction (OER) can promote the phenol degradation through enhanced mass transfer efficiency. More importantly, the common deactivation issue of phenol electro-oxidation on the inert anode can be eliminated by the high OER activity of the active anode. The constructed full electrolytic cell only needs a low potential of 1.498 V to achieve 10 mA/cm² for water electrolysis. The reported promotion effect of phenol degradation by OER as well as the improved anode resistance to deactivation offer new insights into efficient and robust waste-to-resource electrolysis system for water treatment.

A High Flux Electrochemical Filtration System Based on Electrospun Carbon Nanofiber Membrane for Efficient Tetracycline Degradation

In this work, an electrochemical filter using an electrospun carbon nanofiber membrane (ECNFM) anode fabricated by electrospinning, stabilization and carbonization was developed for the removal of antibiotic tetracycline (TC). ECNFM with 2.5 wt% terephthalic acid (PTA) carbonized at 1000 °C (ECNFM-2.5%-1000) exhibited higher tensile stress (0.75 MPa) and porosity (92.8%), more graphitic structures and lower electron transfer resistance (23.52 Ω). Under the optimal condition of applied voltage 2.0 V, pH 6.1, 0.1 mol L−1 Na2SO4, initial TC concentration 10 ppm and membrane flux 425 LMH, the TC removal efficiency of the electrochemical filter of ECNFM-2.5%-1000 reached 99.8%, and no obvious performance loss was observed after 8 h of continuous operation. The pseudo-first-order reaction rate constant in flow-through mode was 2.28 min−1, which was 10.53 times higher than that in batch mode. Meanwhile, the energy demand for 90% TC removal was only 0.017 kWh m−3. TC could be converted to intermediates with lower developmental toxicity and mutagenicity via the loss of functional groups (-CONH2, -CH3, -OH, -N(CH3)2) and ring opening reaction, which was mainly achieved by direct anodic oxidation. This study highlights the potential of ECNFM-based electrochemical filtration for efficient and economical drinking water purification.

Carbon nanotube filter functionalized with MIL-101(Fe) for enhanced flow-through electro-Fenton

Herein, an electrochemical carbon nanotubes (CNT) filter modified with MIL-101(Fe) has been designed for the electro-Fenton applications by serving as a functional flow-through electrode. Under an electric field, the hybrid filter enabled the in situ generation of H₂O₂via the two-electron oxygen reduction reaction, which promoted the production of HO by the accelerated Fe²⁺/Fe³⁺ cycling of MIL-101(Fe). It was observed that 93.2 ± 1.2% tetracycline and 69.0 ± 0.8% total organic carbon (TOC) were removed in 2 h under the optimized conditions. The electron paramagnetic resonance (EPR) analysis and radical scavenging experiments revealed that HO predominated the tetracycline degradation. As compared to the batch reactor, the performance of the proposed system was improved by 5.6 times owing to the convection-enhanced mass transport. The plausible working mechanism and degradation pathway were also subsequently proposed. The findings reported in this study provide a promising insight for the environmental remediation by integrating nanotechnology and Fenton chemistry.

Peroxymonosulfate activation by Fe3O4-MnO2/CNT nanohybrid electroactive filter towards ultrafast micropollutants decontamination: Performance and mechanism

Electrocatalytic peroxymonosulfate (PMS) activation is a promising advanced oxidation process for the degradation of micropollutants. Herein, we developed an electroactive carbon nanotube (CNT) filter functionalized with Fe₃O₄-MnO₂ hybrid (Fe₃O₄-MnO₂/CNT) to activate PMS towards ultrafast degradation of sulfamethoxazole (SMX). SMX was completely degraded via a single-pass through the nanohybrid filter (τ < 2 s). The ultrafast degradation kinetics were maintained across a wide pH range (from 3.0 to 8.0), in complicated matrices (e.g., tap water, lake water, WWTP effluent and pharmaceutical wastewater), and for the degradation of various persistent micropollutants. Compared with a conventional batch reactor, the flow-through operation provides an 9.2-fold higher SMX degradation kinetics by virtue of the convection-enhanced mass transport (1.47 vs. 0.16 min^-1). The efficient redox cycle of Fe²⁺/Fe³⁺ and Mn²⁺/Mn⁴⁺ facilitate the PMS activation to generate SO₄^•- under electric field. Meanwhile, the ketonic groups on the CNT provide active sites for the generation of ¹O₂. Both experimental and theoretical results revealed the superior activity of nanohybrid filter associated with the synergistic effects among Fe, Mn, CNT and electric field. Therefore, the electrocatalytic filter based PMS activation system provides a green strategy for the remediation of micropollutants in a sustainable manner.

Insight into the rapid elimination of low-concentration antibiotics from natural waters using tandem multilevel reactive electrochemical membranes: Role of direct electron transfer and hydroxyl radical oxidation

Herein, we reported a tandem multilevel reactive electrochemical membrane (REM) system was promising for the rapid and complete removal of trace antibiotics from natural waters. Results indicate that a four-stage REM module-in-series system achieved steady over 98% removal of model antibiotic norfloxacin (NOR, 100 μg·L^-1) from wastewater treatment plant final effluent and surface water with a residence time of 5.4 s, and the electric energy consumption was only around 0.007-0.011 kWh·m^-3. As for the oxidation mechanism, direct electron transfer (DET) oxidation process played an important role in NOR rapid oxidation, enabling the REM system to tolerate various ^•OH scavenges in natural waters, including natural organic matters, Cl^- and HCO₃^-, even at very high concentration levels. Meanwhile, ^•OH-mediated indirect oxidation process promotes the oxidation and mineralization of NOR. Although the DET-dominated oxidation mechanism makes the REM system cannot achieve the complete mineralization of NOR with residence times of few seconds, the antibacterial activity from NOR was completely eliminated. This REM system featured effective removal performance of trace contaminants with low energy cost and was tolerant to complex waster matrix, suggesting that it could be a powerful supplementary step for wastewater/water treatment.

Fabrication of a permeable SnO2-Sb reactive anodic filter for high-efficiency electrochemical oxidation of antibiotics in wastewater

Electrochemical oxidation (ECO) is an appealing technology for treating emerging organic pollutants in wastewater. However, the conventional flow-by ECO process is expensive with a low energy efficiency owing to the limitations of mass transport of contaminants to the limited surface area of the anode. In this study, a novel freestanding porous and permeable SnO₂-Sb anode was fabricated by one-step sintering using micrometer-sized (NH₄)₂CO₃ grains as the pore-forming agents. This permeable SnO₂-Sb anode without Ti substrate functioned as a reactive anodic filter (RAF) in an ECO cell to treat wastewater containing ciprofloxacin (CIP). Forcing the wastewater through the porous RAF depth-wise improved the mass transport and vastly enlarged the electroactive surface area. Compared with the conventional flow-by configuration, the flow-through RAF exhibited a 12-fold increase in the mass transfer rate constant (60.7 × 10^-6 m s^-1) and a 5-fold increase in the CIP degradation rate constant (0.077 min^-1). At a cell potential of 4.0 V, more than 92% of the CIP was degraded in a single-pass operation at a filtration flux of 54 L m^-2 h^-1 and a short retention time of 1.7 min through the RAF. The robustness and stability of the RAF were demonstrated by its remarkable CIP degradation efficacy of 99% during 200 h of operation. The mechanism of CIP degradation was examined using probe molecules and density functional theory calculations and found to be a combined effect of direct electron transfer and oxidation by generated radicals (OH and SO₄^-). The great potential of RAF in flow-through ECO was further validated by its effective removal (>92%) of various organic pollutants in actual municipal wastewater at a low energy consumption of 0.33 kWh m^-3. The RAF-based ECO process thus provides an advanced environmental technology for the oxidation of toxic and recalcitrant organic pollutants in wastewater treatment.

Electrochemical removal of tetrabromobisphenol A by fluorine-doped titanium suboxide electrochemically reactive membrane

This study reports fluorine-doped titanium suboxide anode for electrochemical mineralization of hydrophobic micro-contaminant, tetrabromobisphenol A. Fluorinated TiSO anode promoted electro-generated hydroxyl radicals (•OH) with higher selectivity and activity, due to increased O₂ evolution potential and more loosely interaction with hydrophobic electrode surface. For electro-oxidation process, fluorine doping had an insignificant impact on outer-sphere reaction and exerted inhibition on inner-sphere reaction, as indicated by cyclic voltammogram performed on Ru(NH₃)₆^3+/2+, Fe(CN)₆^3-/4- and Fe^3+/2+ redox couple. This facilitated electrochemical conversion of TBBPA and intermediates via more efficient outer-sphere reaction and hydroxylation route. Additionally, generated O₂ micro-bubbles could be stabilized on hydrophobic F-doped TiSO anode, which extended the three-phase boundary available for interfacial enrichment of TBBPA and subsequent mineralization. Under action of these comprehensive factors, 0.5% F-doped TiSO electrochemically reactive membrane could achieve 99.7% mineralization of TBBPA upon energy consumption of 0.52 kWh m^-3 at current density of 7.8 ± 0.24 mA cm^-2 (3.75 V vs SHE) and flow rate of 1628 LHM based on flow-through electrolysis. The modified anode exhibited superior performances compared with un-modified one with more efficient TBBPA removal, less toxic intermediate accumulation and lower energy consumption. The results may have important implications for electrochemical removal and detoxification of hydrophobic micro-pollutants.

Graphene-based sponges for electrochemical degradation of persistent organic contaminants

Graphene-based sponges doped with atomic nitrogen and boron were applied for the electrochemical degradation of persistent organic contaminants in one-pass, flow-through mode, and in a low-conductivity supporting electrolyte. The B-doped anode and N-doped cathode was capable of >90% contaminant removal at the geometric anodic current density of 173 A m^-2. The electrochemical degradation of contaminants was achieved via the direct electron transfer, the anodically formed O₃, and by the OH^• radicals formed by the decomposition of H₂O₂ produced at the cathode. The identified transformation products of iopromide show that the anodic cleavage of all three C-I bonds at the aromatic ring was preferential over scissions at the alkyl side chains, suggesting a determining role of the π- π interactions with the graphene surface. In the presence of 20 mM sodium chloride (NaCl), the current efficiency for chlorine production was <0.04%, and there was no chlorate and perchlorate formation, demonstrating a very low electrocatalytic activity of the graphene-based sponge anode towards chloride. Graphene-based sponges were produced using a low-cost, bottom-up method that allows easy introduction of dopants and functionalization of the reduced graphene oxide coating, and thus tailoring of the material for the removal of specific contaminants.

Electrochemical advanced oxidation processes coupled with membrane filtration for degrading antibiotic residues: A review on its potential applications, advances, and challenges

Antibiotic pollution is mainly caused by aquaculture wastewater and pharmaceuticals, which are frequently used by humans. Due to limited treatment efficiency or improper selection of treatment methods, these antibiotic residues may be very harmful in human drinking water and aquatic environments. The EAOPs coupling membrane technology (EAOPs-membrane) can play their own advantages, which can significantly improve the degradation efficiency and alleviate membrane pollution (electrochemical manners). In this context, this review mainly collecting researches and information on EAOPs-membrane treatment of antibiotic pollution published between 2012 and 2020. Discussed the different combinations of these two technologies, the mechanism of them in the system to improve the processing efficiency, prolong the working time, and stabilize the system structure. Mainly due to the synergistic effect of electrochemical behavior such as electric repulsion and in-situ oxidation, the membrane fouling in the system is alleviated. In this review it was summarized that the selection of different membrane electrode materials and their modifications. The paper also elaborates the existing challenges facing the EAOPs-membrane methods for antibiotic pollution treatment, and their prospects.

Flow anodic oxidation: Towards high-efficiency removal of aqueous contaminants by adsorbed hydroxyl radicals at 1.5 V vs SHE

Electrochemical advanced oxidation processes (EAOPs) have emerged as a promising water treatment alternative but major breakthroughs are still needed in order for EAOPs to be competitive with traditional treatment technologies in terms of energy cost. Most existing studies have been conducted at high potentials to generate the powerful hydroxyl radical oxidant (aqueous •OH). While adsorbed hydroxyl radicals (OH*) may form at a much lower energy cost, their possible utilization is limited due to the poor mass transfer of this highly reactive species on solid electrodes. In this report, we describe a novel flow anode system using 4-16 μm Magnéli phase titanium suboxide particles as the anode material which enables the generation of a high steady state •OH concentration (5.4 × 10^-12 mol m^-2) at only 1.5 V (vs SHE) in a dilute electrolyte (5 mM KH₂PO₄). The energy cost of removal per order of selected water contaminants (tetracycline and orange II in this study) using the flow anode is 1.5--6.7 Wh m^-3, which is 1 - 4 orders of magnitude lower than that of existing techniques. The anode material used demonstrates great stability with the configuration readily scaled up. The results of this study provide new insight into a high efficiency, low cost water treatment technology for organic contaminant degradation.

Fabrication of one dimensional hierarchical WO3/BiOI heterojunctions with enhanced visible light activity for degradation of pollutants

One-dimensional (1D) hierarchical WO₃/BiOI p–n (WB) heterojunctions with different mass percentages of WO₃ were fabricated through a precipitation process. Various analytical techniques were employed to characterize the resulting WB composites, and their photocatalytic properties were measured by the degradation of rhodamine B (RhB) and methylene blue (MB) under irradiation of visible light. The WB heterojunctions showed largely enhanced photocatalytic performance as compared to the pure photocatalysts. Notably, the degradation rate constant of RhB by WB-10 was 3.3 and 33.6 times higher than those of pure BiOI and WO₃, respectively. The enhanced activity could be attributed to the hierarchical p–n heterostructures, which can supply more reaction sites and effectively promote the separation of photogenerated charge carriers, as confirmed by PL and photocurrent. Trapping experiments implied that holes (h⁺) and superoxide anion radicals (˙O₂⁻) were the dominant active species for organic pollutants decomposition on the WB composites. This work may benefit the construction of hierarchical heterostructures with high photocatalytic efficiency.

One-dimensional (1D) hierarchical WO₃/BiOI p–n (WB) heterojunctions with different mass percentages of WO₃ were fabricated through a precipitation process.