Bioinspired Interface Engineering for Moisture Resistance in Nacre-Mimetic Cellulose Nanofibrils/Clay Nanocomposites

Polydopamine-coated montmorillonite micro/nanoparticles enhanced pectin-based sprayable multifunctional liquid mulching films: Wind erosion resistance, water retention, and temperature increase/heat preservation properties

Natural biopolymer-based liquid mulching films (LMF) have received widespread attention, whereas the fragile structure and limited functionality have severely restricted their application. Herein, polydopamine-coated montmorillonite micro/nanoparticles enhanced pectin-based sprayable multifunctional liquid mulching films (P-MMT@PDA LMF) were prepared. Dopamine has abundant active sites, and its self-polymerization onto the surface of MMT improves the compatibility of MMT with pectin chains, facilitates the homogeneous dispersion of MMT@PDA in pectin polymers, and makes them more tightly entangled through hydrogen bonding. Therefore, P-MMT@PDA LMF exhibits better mechanical properties (improved by 64.94 N) and wind erosion resistance (wind speed 30 m/s, >60 min). Moreover, MMT@PDA micro/nanoparticles can fill the voids of pectin chains, thus increasing the densification and complexity of the network structure in LMF, enabling better water retention (improved by 14.67 %) and heat preservation (increased by 3.14 °C). Meanwhile, the photothermal effect of PDA endows P-MMT@PDA LMF with a warming effect (increased by 2.84 °C). Hence, this LMF promote wheat growth and demonstrate good biodegradability. These results suggest that the application of P-MMT@PDA LMF is an effective strategy in the environments of drought and cold, which is expected to provide a green solution for sustainable agricultural development and environmental protection in the future.

Innovative applications of bio-inspired technology in bio-based food packaging

Traditionally, food packaging was used to extend the shelf life of food or to monitor its condition. Inspired by many biological structures found in nature, bio-inspired functional materials for bio-based food packaging have been shown to have significantly improved capabilities over traditional bio-based food packaging materials in various aspects and to attract consumers through novel freshness preservation features. This review synthesizes recent advances in bio-inspired bio-based food packaging materials that mimic the structure of natural organisms with specific functionalities, with examples of specific biomimetics in different enhancement areas. In general, bio-based materials have certain disadvantages compared to polymer materials, so there is an urgent need for improvement and enhancement in many areas. Biomimicry further inspires the realization of enhancing some basic functions of bio-based materials for packaging (hydrophobicity, mechanical strength, antimicrobial properties, optical properties) and endowing bio-based materials with more new responsiveness and other functions. What is more interesting is that the inspiration of bionics is taken from nature, and such a perspective can also promote further progress and innovation of bio-based food packaging materials.

Hybrid chiral nanocellulose-cyanidin composite with pH and humidity response for visual inspection and real-time tracking of shrimp quality and freshness

Biobased multi-stimulation materials have received considerable attention for intelligent packaging and anti-counterfeiting applications. Cellulose nanocrystals (CNCs) and cyanidins are good material candidates for monitoring food freshness as they are eco-friendly natural substances. This work incorporated cyanidin with a CNC-hosting substrate to develop a simple, environment-friendly colorimetric device to visualize food freshness. Across the pH range of 2-13, the indicator exhibited noticeable color changes ranging from red to gray and eventually to orange. The CNC-cyanidin (CC) film exhibited a dramatic color change from blue to dark red and high sensitivity at a relative humidity of 30 %-100 %. In corresponding to the total volatile elemental nitrogen (TVB-N) level of shrimp, the indicator showed distinguishable colors at different stages of shrimp. The findings imply that the samples have substantial potential for use as an intelligent indicator for tracking shrimp freshness.

Application progress of nanocellulose in food packaging: A review

With the increasing environmental and ecological problems caused by petroleum-based packaging materials, the focus has gradually shifted to natural resources for the preparation of functional food packaging materials. In addition to biodegradable properties, nanocellulose (NC) mechanical properties, and rich surface chemistry are also fascinating and desired to be one of the most probable green packaging materials. In this review, we firstly introduce the recent progress of novel applications of NC in food packaging, including intelligent packaging, nano(bio)sensors, and nano-paper; secondly, we focus on the modification techniques of NC to summarize the properties (antimicrobial, mechanical, hydrophobic, antioxidant, and so on) that are required for food packaging, to expand the new synthetic methods and application areas. After presenting all the latest advances related to material design and sustainable applications, an overview summarizing the safety of NC is presented to promote a continuous and healthy movement of NC toward the field of truly sustainable packaging.

A review of cellulose-based catechol-containing functional materials for advanced applications

With the increment in global energy consumption and severe environmental pollution, it is urgently needed to explore green and sustainable materials. Inspired by nature, catechol groups in mussel adhesion proteins have been successively understood and utilized as novel biomimetic materials. In parallel, cellulose presents a wide class of functional materials rating from macro-scale to nano-scale components. The cross-over among both research fields alters the introduction of impressive materials with potential engineering properties, where catechol-containing materials supply a general stage for the functionalization of cellulose or cellulose derivatives. In this review, the role of catechol groups in the modification of cellulose and cellulose derivatives is discussed. A broad variety of advanced applications of cellulose-based catechol-containing materials, including adhesives, hydrogels, aerogels, membranes, textiles, pulp and papermaking, composites, are presented. Furthermore, some critical remaining challenges and opportunities are studied to mount the way toward the rational purpose and applications of cellulose-based catechol-containing materials.

Removal of Nanoplastics from Copollutant Systems Using Seaweed Cellulose Nanofibers

Nanoplastic pollution poses a significant global concern for public health due to the potential toxicity it induces in the human body through food and water intake. Consequently, the urgent task of removing nanoplastics, especially from water resources, is paramount for enhancing food safety, and developing eco-friendly materials capable of efficiently removing nanoplastics is crucial. In this context, we propose the use of biodegradable anionic seaweed cellulose nanofibers (TEMPO-mediated seaweed cellulose nanofibers, TCNFs) and cationic seaweed cellulose nanofibers (quaternized seaweed cellulose nanofibers, QCNFs) for nanoplastic removal in both single- and copollutant systems. In our experiments under simulated practical conditions, we revealed that TCNFs and QCNFs achieved an average removal efficiency of 98.71% against nanoplastic particles. Moreover, TCNFs and QCNFs exhibited higher adsorption capacities compared to those of existing materials, potentially offering a cost-effective advantage. Toxicity assessments conducted with mammalian cells further confirmed the biosafety of TCNFs and QCNFs. This study contributes to the scientific and theoretical understanding of using edible seaweed as well as offers promising solutions for food safety control in an efficient, cost-effective, and eco-friendly manner.

Robust, biodegradable and flame-retardant nanocomposite films based on TEMPO-oxidized cellulose nanofibers and hydroxyapatite nanowires

Flammability is a fatal drawback for sustainable packaging materials made from cellulose and its derivatives. Incorporating inorganic nanomaterials is a viable approach to improve the fire-resistant property. However, due to the aggregation of inorganic fillers and weak interactions between components, incorporating inorganic nanomaterials always had an adverse impact on the mechanical properties and optical transparency of cellulose-based nanocomposites. Herein, we presented a robust, biodegradable, and flame-retardant nanocomposite film composed of TEMPO-oxidized cellulose nanofibers (TOCNFs) and inorganic hydroxyapatite nanowires (HNWs). Both TOCNFs and HNWs possessed one-dimensional microstructure and could form unique organic-inorganic networks microstructure. The organic-inorganic networks interact through physical intertwinement and multiple chemical bonds, endowing nanocomposite film with outstanding mechanical properties. This nanocomposite film showed a tensile strength of 223.68 MPa and Young's modulus of 9.18 GPa, which were superior to most reported cellulose-based nanocomposite. Furthermore, this nanocomposite film demonstrated exceptional thermal stability and flame-retardant feature attributed to the inorganic framework formed by HNWs. This nanocomposite film also possessed a high optical transmittance even when HNWs content reached 30 % and could be decomposed quickly in soil. By employing organic-inorganic interpenetrating network structure design and multiple bonding interaction, cellulose-based nanocomposites can overcome inherent limitations and attain desirable comprehensive properties.

A Review on Barrier Properties of Cellulose/Clay Nanocomposite Polymers for Packaging Applications

Packaging materials are used to protect consumer goods, such as food, drinks, cosmetics, healthcare items, and more, from harmful gases and physical and chemical damage during storage, distribution, and handling. Synthetic plastics are commonly used because they exhibit sufficient characteristics for packaging requirements, but their end lives result in environmental pollution, the depletion of landfill space, rising sea pollution, and more. These exist because of their poor biodegradability, limited recyclability, etc. There has been an increasing demand for replacing these polymers with bio-based biodegradable materials for a sustainable environment. Cellulosic nanomaterials have been proposed as a potential substitute in the preparation of packaging films. Nevertheless, their application is limited due to their poor properties, such as their barrier, thermal, and mechanical properties, to name a few. The barrier properties of materials play a pivotal role in extending and determining the shelf lives of packaged foods. Nanofillers have been used to enhance the barrier properties. This article reviews the literature on the barrier properties of cellulose/clay nanocomposite polymers. Cellulose extraction stages such as pretreatment, bleaching, and nanoparticle isolation are outlined, followed by cellulose modification methods. Finally, a brief discussion on nanofillers is provided, followed by an extensive literature review on the barrier properties of cellulose/clay nanocomposite polymers. Although similar reviews have been presented, the use of modification processes applied to cellulose, clay, and final nanocomposites to enhance the barrier properties has not been reviewed. Therefore, this article focuses on this scope.

Affine Deformation and Self-Assembly Alignment in Hydrogel Nanocomposites

Tailoring the order in hierarchical structures is a key goal of bioinspired nanocomposite design. Recently, nacre-like materials have been developed by solvent evaporation methods that are scalable and attain advanced functionalities. However, understanding the alignment mechanisms of 2D fillers, nanosheets, or platelets remains challenging. This work explores possible pathways for nanocomposite ordering via orientation distribution functions. We demonstrate how the immobilization of 2D materials via (pseudo)network formation is crucial to alignment based on evaporation. We show a modified affine deformation model that describes such evaporative methods. In this, a gel network develops enough yield stress and uniformly deforms as drying proceeds, along with the immobilized particles, causing an in-plane orientation. Herein, we tested the dominance of this approach by using a thermo-reversible gel for rapid montmorillonite (MMT) particle fixation. We researched gelatin/MMT as a model system to investigate the effects of high loadings, orientational order, and aspect ratio. The nacre-like nanocomposites showed a semiconstant order parameter (⟨P2⟩ ∼ 0.7) over increasing nanofiller content up to 64 vol % filler. This remarkable alignment resulted in continuously improved mechanical and water vapor barrier properties over unusually large filler fractions. Some variations in stiffness and diffusion properties were observed, possibly correlated to the applied drying conditions of the hybrid hydrogels. The affine deformation strategy holds promise for developing next-generation advanced materials with tailored properties even at (very) high filler loadings. Furthermore, a gelling approach offers the advantages of simplicity and versatility in the formulation of the components, which is useful for large-scale fabrication methods.

A superstable, flexible, and scalable nanofluidic ion regulation composite membrane

Two-dimensional layered membranes with high and stable ion transport properties have various applications in nanofluidic devices; however, their construction remains a considerable challenge. Herein, we develop a superstable aramid nanofiber/graphite composite membrane with numerous one-dimensional and two-dimensional nano-confined interspaces for ultrafast ion transport. The fabricated flexible and scalable membrane exhibits high tensile strength (∼115.3 MPa) even after immersion in water for 90 days. Further, the aramid nanofiber/graphite conductor features the surface-charge-governed ion transport behavior. The ionic conductivity of the membrane at a low potassium chloride concentration of 10-4 mol/L can be enhanced by 16 times that of the bulk counterpart. More importantly, its structure and ionic conductivity remain unchanged even after immersion in different harsh solutions (e.g., acid, base, and ethanol) for over 30 days. Molecular dynamics simulations reveal that the superstability of the membrane is attributable to the robust interchain interactions within the aramid nanofibers and the strong interfacial interactions between the aramid nanofibers and graphite nanosheets. This study highlights the superior structural stability of the proposed flexible and scalable aramid nanofiber/graphite composite membrane, which could be employed in advanced nanofluidic devices for application under extreme working environments.

The Colloidal Properties of Nanocellulose

Nanocelluloses are anisotropic nanoparticles of semicrystalline assemblies of glucan polymers. They have great potential as renewable building blocks in the materials platform of a more sustainable society. As a result, the research on nanocellulose has grown exponentially over the last decades. To fully utilize the properties of nanocelluloses, a fundamental understanding of their colloidal behavior is necessary. As elongated particles with dimensions in a critical nanosize range, their colloidal properties are complex, with several behaviors not covered by classical theories. In this comprehensive Review, we describe the most prominent colloidal behaviors of nanocellulose by combining experimental data and theoretical descriptions. We discuss the preparation and characterization of nanocellulose dispersions, how they form networks at low concentrations, how classical theories cannot describe their behavior, and how they interact with other colloids. We then show examples of how scientists can use this fundamental knowledge to control the assembly of nanocellulose into new materials with exceptional properties. We hope aspiring and established researchers will use this Review as a guide.

Cellulose: A Review of Water Interactions, Applications in Composites, and Water Treatment

Cellulose is known to interact well with water, but is insoluble in it. Many polysaccharides such as cellulose are known to have significant hydrogen bond networks joining the molecular chains, and yet they are recalcitrant to aqueous solvents. This review charts the interaction of cellulose with water but with emphasis on the formation of both natural and synthetic fiber composites. Covering studies concerning the interaction of water with wood, the biosynthesis of cellulose in the cell wall, to its dispersion in aqueous suspensions and ultimately in water filtration and fiber-based composite materials this review explores water-cellulose interactions and how they can be exploited for synthetic and natural composites. The suggestion that cellulose is amphiphilic is critically reviewed, with relevance to its processing. Building on this, progress made in using various charged and modified forms of nanocellulose to stabilize oil-water emulsions is addressed. The role of water in the aqueous formation of chiral nematic liquid crystals, and subsequently when dried into composite films is covered. The review will also address the use of cellulose as an aid to water filtration as one area where interactions can be used effectively to prosper human life.

Nacre-inspired biodegradable nanocellulose/MXene/AgNPs films with high strength and superior gas barrier properties

Super strength and high barrier properties are the bottleneck of the application of cellulose film materials. Herein, it is reported a flexible gas barrier film with nacre-like layered structure, in which 1D TEMPO-oxidized nanocellulose (TNF) and 2D MXene self-assembled to form an interwoven stack structure with 0D AgNPs filling the void space. The strong interaction and dense structure endowed TNF/MX/AgNPs film with mechanical properties far superior to PE films and acid-base stability. Importantly, the film presented ultra-low oxygen permeability confirmed by molecular dynamics simulations and better barrier properties to volatile organic gases than PE films. It is here considered the tortuous path diffusion mechanism of the composite film responsible for the enhanced gas barrier performance. The TNF/MX/AgNPs film also possessed antibacterial properties, biocompatibility and degradability (completely degraded after 150 days in soil). Collectively, the TNF/MX/AgNPs film brings innovative insights into the design and fabrication of high-performance materials.

Methylene Blue Removed from Aqueous Solution by Encapsulation of Bentonite Aerogel Beads with Cobalt Alginate

It can be difficult to remove dark methylene blue (MB) from water effectively. The use of sodium alginate and bentonite (Ben) as the matrix produced a displacement reaction that occurred in cobalt chloride, which allowed Ben to be successfully encapsulated in cobalt alginate (CA). Finally, a vacuum freeze-drying method was used to prepare a low-cost composite of CA/Ben aerogel for adsorbing MB in aqueous solutions. In addition to scanning electron microscopy, thermogravimetric analysis, and Fourier transform infrared spectroscopy, the composites were also characterized and analyzed. Different adsorption experiments were conducted in order to determine the effects of dosage, pH, adsorption time, and temperature on the adsorption performance of the adsorbent. According to the results of the experiment, the adsorption capacity of CA/Ben aerogel was 258.92 mg·g^-1, and the pseudo-first-order kinetic model and Freundlich isotherm model can fully explain the adsorption process of MB on this aerogel. The composite material reported in this paper is easily recycled, and the removal rate reaches 65% after four times of recycling. Moreover, compared with other adsorbents, the composite material of the invention is highly environmentally friendly and has a simple preparation process. A large-scale application of this technology is the removal of dyes from water on a large scale.

Tolerant chitosan/carboxymethyl cellulose@calcium composite films on nylon fabric for high-flux water/oil separation

Nacre as a natural organic-inorganic composite has outstanding mechanical toughness and oil repellency. Enlightened by nacre, we present here a novel strategy to fabricate superhydrophilic/underwater superoleophobic hybrid films on nylon fabric (NF). The hybrid films were constructed via facile and green layer-by-layer (LbL) assembly of calcium ion (Ca²⁺), chitosan (CS), and carboxymethyl cellulose (CMC) combined with biomimetic mineralization in CO₂ atmosphere. The resulting NF exhibits excellent superoleophobicity underwater, anti-oil-fouling ability, and stability. Under the drive of gravity, the deposited fabric can selectively remove pure and corrosive water from various oil-containing water with preferable separation efficiencies, great water flux (>6903 L·m^-2·h^-1), favorable oil penetration pressure (1.47 kPa), and outstanding recyclability. Especially, the NF can still sustain high underwater oleophobicity after repeatedly separating oil/corrosive water for 80 times. The green preparation process, eco-friendly and durable coating, and good separation performance allow the as-fabricated NF to be applied in oily wastewater treatment.

Interfacial Mechanical Behavior in Nacre of Red Abalone and Other Shells: A Review

Interfaces between nacreous tablets are crucial to the outstanding mechanical properties of nacre in natural shells. Excellent research has been conducted to probe the effect of interfaces on strength and toughness of nacre, providing critical guidelines for the design of human-made laminated composites. This article reviews recent studies on interfacial mechanical behavior of nacre in red abalone and other shells, including experimental methods, analytical and numerical modeling. The discussions focus on the mechanical properties of dry and hydrated nacreous microstructures. The review concludes with discussions on representative studies of nacre-like composites with interfaces tuned using multiple approaches, and provides an outlook on improving the performance of composites with better interfacial controls.

Adhesion advances: from nanomaterials to biomimetic adhesion and applications

The field of adhesion has revealed a significant impact on numerous applications such as wound healing, drug delivery, electrically conductive adhesive, dental adhesive, and wood industry. Nanotechnology has continued to be the primary means to achieve adhesion. Among them, biological systems based on the unique structure of the nano-levels have developed excellent adhesion capabilities after billions of years of evolution and natural selection. Therefore, the research on bionic adhesion inspired by biological systems has gradually emerged. This review firstly focuses on the mechanism of adhesion, and secondly reports the effects of different nanomaterials on adhesion properties. Then based on the structure of mussels, geckos, tree frogs, octopuses, and other organisms, the research progress of biomimetic nanotechnology to achieve adhesion is summarized. Finally, the applications, challenges, and future directions of nanotechnology in new adhesive materials are provided.

Recyclable nanocomposites of well-dispersed 2D layered silicates in cellulose nanofibril (CNF) matrix

Nanocomposites based on components from nature, which can be recycled are of great interest in new materials for sustainable development. The range of properties of nacre-inspired hybrids of 1D cellulose and 2D clay platelets are investigated in nanocomposites with improved nanoparticle dispersion in the starting hydrocolloid mixture. Films with a wide range of compositions are prepared by capillary force assisted physical assembly (vacuum-assisted filtration) of TEMPO-oxidized cellulose nanofibers (TOCN) reinforced by exfoliated nanoclays of three different aspect ratios: saponite, montmorillonite and mica. X-ray diffraction and transmission electron micrographs show almost monolayer dispersion of saponite and montmorillonite and high orientation parallel to the film surface. Films exhibit ultimate strength up to 573 MPa. Young's modulus exceeds 38 GPa even at high MTM contents (40-80 vol%). Optical transmittance, UV-shielding, thermal shielding and fire-retardant properties are measured, found to be very good and are sensitive to the 2D nanoplatelet dispersion.

Barium alginate as a skeleton coating graphene oxide and bentonite-derived composites: Excellent adsorbent based on predictive design for the enhanced adsorption of methylene blue

The phenomenon that calcium alginate does not exhibit high adsorption capacity as a carrier material has not been reasonably explained or solved. In this paper, a new viewpoint that the orbital energy level of metal ions and the binding degree of the α-l-guluronate and β-d-mannuronate units affect the adsorption performance of the composite was innovatively proposed. Taking barium alginate (BA) as an example, the possibility of replacing calcium alginate is discussed. Barium alginate/graphene oxide (BA/GO) membranes and three-dimensional (3D) barium alginate-bentonite-graphene oxide derived (3D-BA) hydrogels were prepared by vacuum freeze-drying to remove methylene blue. The structure and morphology of the prepared adsorbents were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, thermogravimetry and Fourier transform infrared spectroscopy. The effects of adsorbent dosage, doping ratio, temperature, contact time, pH value and initial dye concentration on the adsorption performance of BA composites were investigated. The adsorption capacities of the BA/GO and 3D-BA materials were 1011.3 and 710.3 mg/g, respectively. The BA/GO membrane exhibited stable filtration performance against high concentrations of dyes. Benefiting from the strong interaction between bentonite, sodium alginate and Ba²⁺, the 3D-BA hydrogel showed higher thermal stability and better adsorption efficiency than other materials. The Elovich kinetic model and Sips equation can appropriately describe the adsorption process. The results show that barium alginate is a better carrier material than calcium alginate.

Advanced nanocellulose-based gas barrier materials: Present status and prospects

Nanocellulose based gas barrier materials have become an increasingly important subject, since it is a widespread environmentally friendly natural polymer. Previous studies have shown that super-high gas barrier can be achieved with pure and hierarchical nanocellulose films fabricated through simple suspension or layer-by-layer technique either by itself or incorporating with other polymers or nanoparticles. Improved gas barrier properties were observed for nanocellulose-reinforced composites, where nanocellulose partially impermeable nanoparticles decreased gas permeability effectively. However, for nanocellulose-based materials, the higher gas barrier performance is jeopardized by water absorption and shape deformation under high humidity conditions which is a challenge for maintaining properties in material applications. Thus, numerous investigations have been done to solve the problem of water absorption in nanocellulose-based materials. In this literature review, gas barrier properties of pure, layer-by-layer and composite nanocellulose films are investigated. The possible theoretical gas barrier mechanisms are described, and the prospects for nanocellulose-based materials are discussed.

Mechanical properties of cellulose nanofibril papers and their bionanocomposites: A review

Cellulose nanofibril (CNF) paper has various applications due to its unique advantages. Herein, we present the intrinsic mechanical properties of CNF papers, along with the preparation and properties of nanoparticle-reinforced CNF composite papers. The literature on CNF papers reveals a strong correlation between the intrafibrillar network structure and the resulting mechanical properties. This correlation is found to hold for all primary factors affecting mechanical properties, indicating that the performance of CNF materials depends directly on and can be tailored by controlling the intrafibrillar network of the system. The parameters that influence the mechanical properties of CNF papers were critically reviewed. Moreover, the effect on the mechanical properties by adding nanofillers to CNF papers to produce multifunctional composite products was discussed. We concluded this article with future perspectives and possible developments in CNFs and their bionanocomposite papers.

A High-Wet-Strength Biofilm for Readable and Highly Sensitive Humidity Sensors

Low-cost and flexible biofilm humidity sensors with good wet strength are crucial for humidity detection. However, it remains a great challenge to integrate good reversibility, rapid humidity response, and robust humid mechanical strength in one sensor. In this respect, we report a facile method to prepare a sustainable biofilm (named MC film) from sisal cellulose microcrystals (MSF-g-COOH) and citric acid (CA). After cross-linking with CA, the MC film exhibits excellent wet strength and rapid humidity response. More importantly, MC film can be used over a wide temperature range with excellent durability and reversibility for humidity detection. A highly sensitive humidity sensor fabricated from the MC film exhibits high reversibility and excellent water resistance and can be applied in humidity and personalized breath health monitoring. Our work fills the gap between biomaterial design and high-performance sensing devices.

Force-Induced Self-Assembly of Supramolecular Modified Mica Nanosheets for Ductile and Heat-Resistant Mica Papers

Mica is a naturally abundant layered silicate mineral that has higher strength than other layered silicate minerals, but its inherent brittleness limits its application in some fields. In this work, mica was ultrasonically exfoliated into a single-layered nanomaterial after thermal activation, acidification, sodium replacement, and cetyltrimethylammonium bromide (CTAB) intercalation and then modified with ureido-pyrimidinone (UPy)-based PEG chains. Vacuum-assisted self-assembly was used to construct supramolecularly modified single-layered mica into bulk materials, in which the mica nanosheets were stacked into mica paper. The reversible quadruple hydrogen-bonded UPy moieties provided a high binding constant and significantly improved the strength and toughness of the obtained mica paper. These force-induced assembled mica papers showed significantly improved tensile strength and toughness compared with pure mica paper and simultaneously maintained the heat resistance of the mica materials, which may be good candidates for the substrates of flexible sensors working at higher temperatures.

Customized Cellulose Fiber Paper Enabled by an In Situ Growth of Ultralong Hydroxyapatite Nanowires

Cellulose fiber (CF) paper is a low-cost, sustainable, and flexible substrate, which has gained increasing interest recently. Before practical usage, the functionalization of the pristine CF paper is indispensable to meet requirements of specific applications. Different from conventional surface modification or physical mixing methods, we report in situ growth of ultralong hydroxyapatite nanowires (HAPNWs) with lengths larger than 10 μm on the CF paper. HAPNWs are radially aligned on the surface of CFs, creating a micro/nanoscale hierarchical structure. By means of the excellent ion exchange ability of HAP and the hierarchical structure, the functions of the CF paper can be easily customized. As a proof-of-concept, we demonstrate two kinds of functional CF paper: (1) the photoluminescent CF paper by doping Eu³⁺ and Tb³⁺ ions into the crystal lattice of HAPNWs and (2) the superhydrophobic CF paper by coating poly(dimethylsiloxane) on the HAPNW hierarchical structure, which can be applied for self-cleaning and oil/water separation. It is expected that an in situ growth of ultralong HAPNWs will provide an instructive guideline for designing a CF paper with specific functions.

Surface Charges Control the Structure and Properties of Layered Nanocomposite of Cellulose Nanofibrils and Clay Platelets

The interfacial bonding and structure at the nanoscale in the polymer-clay nanocomposites are essential for obtaining desirable material and structure properties. Layered nanocomposite films of cellulose nanofibrils (CNFs)/montmorillonite (MTM) were prepared from the water suspensions of either CNFs bearing quaternary ammonium cations (Q-CNF) or CNFs bearing carboxylate groups (TO-CNF) with MTM nanoplatelets carrying net surface negative charges by using vacuum filtration followed by compressive drying. The effect of the ionic interaction between cationic or anionic charged CNFs and MTM nanoplatelets on the structure, mechanical properties, and flame retardant performance of the TO-CNF/MTM and Q-CNF/MTM nanocomposite films were studied and compared. The MTM nanoplatelets were well dispersed in the network of TO-CNFs in the form of nanoscale tactoids with the MTM content in the range of 5-70 wt %, while an intercalated structure was observed in the Q-CNF/MTM nanocomposites. The resulting TO-CNF/MTM nanocomposite films had a better flame retardant performance as compared to the Q-CNF/MTM films with the same MTM content. In addition, the effective modulus of MTM for the TO-CNF/MTM nanocomposites was as high as 129.9 GPa, 3.5 times higher than that for Q-CNF/MTM (37.1 GPa). On the other hand, the Q-CNF/MTM nanocomposites showed a synergistic enhancement in the modulus and tensile strength together with strain-to-failure and demonstrated a much better toughness as compared to the TO-CNF/MTM nanocomposites.

Plant celluloses, hemicelluloses, lignins, and volatile oils for the synthesis of nanoparticles and nanostructured materials

A huge variety of plants are harvested worldwide and their different constituents can be converted into a broad range of bionanomaterials. In parallel, much research effort in materials science and engineering is focused on the formation of nanoparticles and nanostructured materials originating from agricultural residues. Cellulose (40-50%), hemicellulose (20-40%), and lignin (20-30%) represent major plant ingredients and many techniques have been described that separate the main plant components for the synthesis of nanocelluloses, nano-hemicelluloses, and nanolignins with divergent and controllable properties. The minor components, such as essential oils, could also be used to produce non-toxic metal and metal oxide nanoparticles with high bioavailability, biocompatibility, and/or bioactivity. This review describes the chemical structure, the physical and chemical properties of plant cell constituents, different techniques for the synthesis of nanocelluloses, nanohemicelluloses, and nanolignins from various lignocellulose sources and agricultural residues, and the extraction of volatile oils from plants as well as their use in metal and metal oxide nanoparticle production and emulsion preparation. Furthermore, details about the formation of activated carbon nanomaterials by thermal treatment of lignocellulose materials, a few examples of mineral extraction from agriculture waste for nanoparticle fabrication, and the emerging applications of plant-based nanomaterials in different fields, such as biotechnology and medicine, environment protection, environmental remediation, or energy production and storage, are also included. This review also briefly discusses the recent developments and challenges of obtaining nanomaterials from plant residues, and the issues surrounding toxicity and regulation.

Mild and Versatile Functionalization of Nacre-Mimetic Cellulose Nanofibrils/Clay Nanocomposites by Organocatalytic Surface Engineering

Development of surface-engineering strategies, which are facile, versatile, and mild, are highly desirable in tailor-made functionalization of high-performance bioinspired nanocomposites. We herein disclose for the first time a general organocatalytic strategy for the functionalization and hydrophobization of nacre-mimetic nanocomposites, which includes vide supra key aspects of surface engineering. The merging of metal-free catalysis and the design of nacre-mimetic nanocomposite materials were demonstrated by the organocatalytic surface engineering of cellulose nanofibrils/clay nanocomposites providing the corresponding bioinspired nanocomposites with good mechanical properties, hydrophobicity, and useful thia-, amino, and olefinic functionalities.

Functional biohybrid materials based on halloysite, sepiolite and cellulose nanofibers for health applications

Biohybrid materials were prepared by co-assembling the three following components: nanotubular halloysite, microfibrous sepiolite, and cellulose nanofibers dispersed in water, in order to exploit the most salient features of each individual component and to render homogeneous, flexible, yet strong films. Indeed, the incorporation of halloysite improves the mechanical performance of the resulting hybrid nanopapers and the assembly of the three components modifies the surface features concerning wetting properties compared to pristine materials, so that the main characteristics of the resulting materials become tunable with regard to certain properties. Owing to their hierarchical porosity together with their diverse surface characteristics, these hybrids can be used in diverse biomedical/pharmaceutical applications. Herein, for instance, loading with two model drugs, salicylic acid and ibuprofen, allows controlled and sustained release as deduced from antimicrobial assays, opening a versatile path for developing other related organic-inorganic materials of potential interest in diverse application fields.

Cellulose-based biomaterials integrated with copper-cystine hybrid structures as catalysts for nitric oxide generation

Bionanocomposite materials were developed from the assembly of polymer-coated copper-cystine high-aspect ratio structures (CuHARS) and cellulose fibers. The coating of the metal-organic materials with polyallylamine hydrochloride (PAH) allows their covalent linkage to TEMPO-oxidized cellulose by means of EDC/NHS. The resulting materials can be processed as films or macroporous foams by solvent casting and lyophilization, respectively. The films show good mechanical behavior with Young's moduli around 1.5 GPa as well as resistance in water, while the obtained foams show an open network of interconnected macropores with average diameters around 130 μm, depending on the concentration of the initial suspension, and compression modulus values around 450 kPa, similar to other reported freeze-dried nanocellulose-based aerogels. Based on these characteristics, the cellulose/PAH-CuHARS composites are promising for potential biomedical applications as implants or wound dressing materials. They have proved to be effective in the decomposition of low molecular weight S-nitrosothiols (RSNOs), similar to those existing in blood, releasing nitric oxide (NO). This effect is attributed to the presence of copper in the crystalline structure of the CuHARS building unit, which can be gradually released in the presence of redox species like ascorbic acid, typically found in blood. The resulting biomaterials can offer the interesting properties associated with NO, like antimicrobial activity as preliminary tests showed here with Escherichia coli and Staphylococcus epidermidis. In the presence of physiological concentration of RSNOs the amount of generated NO (around 360 nM) is not enough to show bactericidal effect on the studied bacteria, but it could provide other properties inherent to NO even at low concentration in the nM range like anti-inflammatory and anti-thrombotic effects. The cytotoxic effect recorded of the films on rat brain endothelial cells (BMVECs) is least significant and proves them to be friendly enough for further biological studies.

Composites of nanofibrillated cellulose with clay minerals: A review

Biopolymers-based composites are, in general, environmentally friendly materials, which can be obtained from renewable sources. Some of them can also present promising properties to be used in food packaging and electronic devices, being thus logical substitutes to petroleum-based polymers, specifically plastics. Cellulose nanofibrils (CNF) obtained by chemical/enzymatic pre-treatments followed by a mechanical treatment appear as a new suitable biomaterial. However, CNF are still quite expensive materials, due to the required chemicals/equipment/energy involved, and additionally, they present some limitations such as high hydrophilicity/high water vapour permeability. The combination of CNF with clay minerals, such as montmorillonite or kaolinite, as widely available geo-resources, represents an excellent way to reduce the amount of CNF used, enabling the production of valuable materials and reducing costs; and, at the same time it is possible to improve the characteristics of the formed materials, such as mechanical, gas barrier and fire retardancy properties, if appropriate conditions of preparation are used. Nevertheless, to obtain hybrid CNF/clay composites with superior properties it is necessary to ensure a good dispersion of the inorganic material in the CNF suspension and a good compatibility among the inorganic and organic components. To fulfil this goal, several strategies can be considered, including physical treatments of the suspensions, CNF and clay surface chemical modifications, and the use of a coupling agent. In this review article, the state-of-the-art on a new emerging generation of composites (films, foams or coatings) based on nanofibrillated cellulose and nanoclay, with focus on strategies for their preparation and most relevant achievements is critically reviewed, bearing in mind their potential application as substitutes for common plastics. A third component has been eventually added to these organic-inorganic hybrids, e.g., chitosan, carboxymethylcellulose, borate or epoxy resin, to enhance specific characteristics of the material. Some general background on the production of different types of CNF and their main properties is previously provided.

Macroporous bacterial cellulose grafted by oligopeptides induces biomimetic mineralization via interfacial wettability

Bacterial cellulose (BC) has a role in tissue repair and regenerative medicine, which has already attracted tremendous interest from researchers, especially those working in the field of hybrid materials. Herein, we designed BC-based macroporous functional materials by dialdehyde bacterial cellulose (DBC) cross-linking with oligopeptides under mild reactive conditions. The interfacial properties of the surface modified BC were examined by biomimetic mineralization. The results showed that a macroporous structure was achieved by using oligopeptides as chemical cross-linking agents with an interconnected macroporosity ranging from 20 μm to 80 μm. Their mechanical properties were barely altered compared to the pristine BC. Their enhanced surface charges stemmed from the carboxyl groups of the oligopeptides engaging in reactions with amine and aldehyde groups. The oligopeptides cross-linked DBC showed a faster initial induction towards minerals via interfacial wettability resulting in promotion of mineralization, the hybrid materials had excellent biocompatibility relative to the pristine BC. These findings are vital to the development of other biopolymers with essential macroporous structures as well as improved interfacial wettability, which enables their possible uses in tissue repair and regenerative medicine.

Bioinspired approach to enhance mechanical properties of starch based nacre-mimetic nanocomposite

In this work, a facile biomimetic method was proposed to enhance the interfacial adhesion between layered clay and polymer matrix inspired by strong adhesion of mussel adhesive proteins. Montmorillonite (MMT) was coated with a thin layer of polydopamine (PDA) through self-polymerization of dopamine (DA) and subsequently assembled with corn starch (CS) to generate CS/MMT-DA nanocomposite. FTIR, XPS, SEM and XRD results demonstrated that PDA coating benefited not only the intercalation and dispersion of the modified MMT (MMT-DA) in the polymer matrix but also the strong interfacial adhesion between filler and matrix. The tensile strength of CS/MMT-DA nanocomposites was largely enhanced by increasing the amount of DA or polymerization time. This work can largely expand the application of MMT and provide a new idea for preparing high performance starch nanocomposites.

Nacre-Mimetic Graphene Oxide/Cross-Linking Agent Composite Films with Superior Mechanical Properties

We report a graphene oxide/cross-linking agent (GO/CA) composite inspired by the nacre structure. Based on the "brick-and-mortar" concept of nacre, graphene oxide and a cross-linking agent are covalently conjugated in the form of nacre. The mechanical characteristics of the nacre-mimetic GO/CA composite film can be controlled by adjusting the preparation method, degree of cross-linking, and cross-linking times. As a result, the cross-linking strategy can drastically enhance the tensile strength [142.9 ± 6.4 MPa (∼2.3-fold)], modulus [4.7 ± 0.36 GPa (∼15.7-fold)], and hardness [917.4 ± 85.7 MPa (∼9.0-fold)], which are superior to those of pristine materials. The cross-linking agent-based chemical bonding method for mechanically improved integration is mainly attributed to the formation of strong cross-linked networks between the GO-based 2D interfaces and CA. The facile fabrication process provides many opportunities to design advanced, robust, and integrated nacre-like GO/CA composites, which can be applied to future aerospace utilizations, electronic protectors, robotic elements, and permeable membranes.

Highly Transparent, Strong, and Flexible Films with Modified Cellulose Nanofiber Bearing UV Shielding Property

This work investigates multifunctional composite films synthesized with cellulose nanofibers (CNFs) and poly(vinyl alcohol) (PVA). First, TEMPO-oxidized CNFs were modified in the heterogeneous phase with benzophenone, diisocyanate, and epoxidized soybean oil via esterification reactions. A thorough characterization was carried out via elemental analysis as well as FT-IR and X-ray photoelectron spectroscopies and solid-state NMR. Following, the surface-modified CNFs were combined with PVA to endow composite films with UV-absorbing capabilities while increasing their thermomechanical strength and maintaining a high light transmittance. Compared to neat PVF films, the tensile strength, Young modulus, and elongation of the films underwent dramatic increases upon addition of the reinforcing phase (maximum values of ∼96 MPa, ∼ 714 MPa, and ∼350%, respectively). A high UV blocking performance, especially in the UVB region, was observed for the introduced multifunctional PVA films at CNF loadings below 5 wt %. The trade-off between modified nanofibril function as interfacial reinforcement and aggregation leads to an optimum loading. The results indicate promising applications, for example, in active packaging.

Nanocellulose, a Versatile Green Platform: From Biosources to Materials and Their Applications

With increasing environmental and ecological concerns due to the use of petroleum-based chemicals and products, the synthesis of fine chemicals and functional materials from natural resources is of great public value. Nanocellulose may prove to be one of the most promising green materials of modern times due to its intrinsic properties, renewability, and abundance. In this review, we present nanocellulose-based materials from sourcing, synthesis, and surface modification of nanocellulose, to materials formation and applications. Nanocellulose can be sourced from biomass, plants, or bacteria, relying on fairly simple, scalable, and efficient isolation techniques. Mechanical, chemical, and enzymatic treatments, or a combination of these, can be used to extract nanocellulose from natural sources. The properties of nanocellulose are dependent on the source, the isolation technique, and potential subsequent surface transformations. Nanocellulose surface modification techniques are typically used to introduce either charged or hydrophobic moieties, and include amidation, esterification, etherification, silylation, polymerization, urethanization, sulfonation, and phosphorylation. Nanocellulose has excellent strength, high Young's modulus, biocompatibility, and tunable self-assembly, thixotropic, and photonic properties, which are essential for the applications of this material. Nanocellulose participates in the fabrication of a large range of nanomaterials and nanocomposites, including those based on polymers, metals, metal oxides, and carbon. In particular, nanocellulose complements organic-based materials, where it imparts its mechanical properties to the composite. Nanocellulose is a promising material whenever material strength, flexibility, and/or specific nanostructuration are required. Applications include functional paper, optoelectronics, and antibacterial coatings, packaging, mechanically reinforced polymer composites, tissue scaffolds, drug delivery, biosensors, energy storage, catalysis, environmental remediation, and electrochemically controlled separation. Phosphorylated nanocellulose is a particularly interesting material, spanning a surprising set of applications in various dimensions including bone scaffolds, adsorbents, and flame retardants and as a support for the heterogenization of homogeneous catalysts.