Selective separation of similarly sized proteins with tunable nanoporous block copolymer membranes

Metal-Organic Framework-Based Surface-Enhanced Raman Scattering Sensing Platform for Trace Malondialdehyde Detection in Tears

Disease biomarkers in tears are crucial for clinical diagnosis and health monitoring. However, the limited volume of tear samples, low concentration of tear biomarkers, and complex tear composition present challenges for precise testing. We introduce a spot-on testing platform of metal-organic framework (MOF)-based surface-enhanced Raman scattering (SERS) capillary column, which is capable of target molecules selective separation and enrichment for tear biomarkers in situ detection. It consists of Au nanostars for effective SERS signal and a porous MOF shell for separating impurities through molecular sieving effect. This platform allows for simultaneous collection and detection of tear, capturing the disease biomarker malondialdehyde in tears with a 9.38 × 10-9 mol/L limit of detection. Moreover, we designed a hand-held device based on this tubular SERS sensor, successfully diagnosing patients with dry eye disease. This functional capillary column enables noninvasive and rapid diagnosis of biomarkers in biofluids, providing potential for disease diagnosis and healthcare monitoring.

High-efficient depletion and separation of histidine-rich proteins via Cu2+-chelated porous polymer microspheres

Depletion and separation of histidine-rich proteins from complicated biosamples are crucial for various downstream applications in proteome research and clinical diagnosis. Herein, porous polymer microspheres coated with polyacrylic acid (SPSDVB-PAA) were fabricated through double emulsion interfacial polymerization technique and followed by immobilization of Cu2+ ions on the surface of SPSDVB-PAA. The as-prepared SPSDVB-PAA-Cu with uniform size and nanoscale pore structure enabled coordination interaction of Cu2+ with histidine residues in his-rich proteins, resulting in high-performance adsorption. As metal affinity adsorbent, the SPSDVB-PAA-Cu exhibited favorable selectivity for adsorbing hemoglobin (Hb) and human serum albumin (HSA) with the maximum adsorption capacities of 152.2 and 100.7 mg g-1. Furthermore, the polymer microspheres were used to isolate histidine-rich proteins from human whole blood and plasma, underscoring their effectiveness. The liquid chromatography tandem mass spectrometry (LC-MS/MS) results indicated that the content of 14 most abundant proteins in human plasma was depleted from 81.6 % to 30.7 % and low-abundance proteins were enriched from 18.4 % to 69.3 % after treatment with SPSDVB-PAA-Cu, illustrating potential application of SPSDVB-PAA-Cu in proteomic research.

An enzymatic continuous-flow reactor based on a pore-size matching nano- and isoporous block copolymer membrane

Continuous-flow biocatalysis utilizing immobilized enzymes emerged as a sustainable route for chemical synthesis. However, inadequate biocatalytic efficiency from current flow reactors, caused by non-productive enzyme immobilization or enzyme-carrier mismatches in size, hampers its widespread application. Here, we demonstrate a general-applicable and robust approach for the fabrication of a high-performance enzymatic continuous-flow reactor via integrating well-designed scalable isoporous block copolymer (BCP) membranes as carriers with an oriented and productive immobilization employing material binding peptides (MBP). Densely packed uniform enzyme-matched nanochannels of well-designed BCP membranes endow the desired nanoconfined environments towards a productive immobilized phytase. Tuning nanochannel properties can further regulate the complex reaction process and fortify the catalytic performance. The synergistic design of enzyme-matched carriers and efficient enzyme immobilization empowers an excellent catalytic performance with >1 month operational stability, superior productivity, and a high space-time yield (1.05 × 105 g L-1 d-1) via a single-pass continuous-flow process. The obtained performance makes the designed nano- and isoporous block copolymer membrane reactor highly attractive for industrial applications.

A Natural Casein-Based Separator with Brick-and-Mortar Structure for Stable, High-Rate Proton Batteries

Rechargeable aqueous proton batteries with small organic molecule anodes are currently considered promising candidates for large-scale energy storage due to their low cost, stable safety, and environmental friendliness. However, the practical application is limited by the poor cycling stability caused by the shuttling of soluble organic molecules between electrodes. Herein, a cell separator is modified by a GO-casein-Cu2+ layer with a brick-and-mortar structure to inhibit the shuttling of small organic molecules. Experimental and calculation results indicate that, attributed to the synergistic effect of physical blocking of casein molecular chains and electrostatic and coordination interactions of Cu2+, bulk dissolution and shuttling of multiple small molecules can be inhibited simultaneously, while H+ transfer across the separators is not almost affected. With the protection of the GO-casein-Cu2+ separator, soluble small molecules, such as diquinoxalino[2,3-a:2',3'-c]phenazine,2,3,8,9,14,15-hexacyano (6CN-DQPZ) exhibit a high reversible capacity of 262.6 mA h g-1 and amazing stability (capacity retention of 92.9% after 1000 cycles at 1 A g-1). In addition, this strategy is also proved available to other active conjugated small molecules, such as indanthrone (IDT), providing a general green sustainable strategy for advancing the use of small organic molecule electrodes in proton cells.

Biomimetic affinity membrane roll column for rapid purification of C-reactive protein

To in-depth explore the action mechanism of C-reactive protein (CRP) and precisely study its signaling pathways, it is essential to acquire high-purity CRP while preserving its intact structure and functionality. In this study, we propose and fabricate a high-density 2-methacryloyloxyethyl phosphorylcholine (MPC)-modified membrane roll column (MPC-MRC) using a surface-initiated atom transfer radical polymerization (SI-ATRP) approach, which can overcome these limitations (long incubation time and low adsorption capacity) of conventional enrichment materials. The MPC-MRC incorporates a high-density 2-hydroxyethyl methacrylate polymer brush to prevent non-specific protein adsorption and multiple MPC polymer brush layers for high-performance enrichment of CRP in the company of calcium ions. Furthermore, the MPC-MRC exhibits high permeability, hydrophilicity, and mechanical strength. Compared to previous technologies, this novel material demonstrates significantly higher CRP binding capacity (310.3 mg/g), shorter processing time (only 15 min), and lower cost (only 12 USD/column). Notably, the MPC-MRC enables fast and effective purification of CRP from both human and rat serum, exhibiting good selectivity, recovery (> 91.3 %), and purity (> 95.2 %). Thus, this proposed purification approach based on MPC-MRC holds great potential for target protein enrichment from complex samples, as well as facilitating in-depth studies of its biological functions.

Diblock and Triblock Copolymers as Nanostructured Precursors to Functional Nanoporous Materials: From Design to Application

Block copolymers have gained tremendous interest from the scientific community in the last two decades. These macromolecular architectures indeed constitute ideal nanostructured precursors for the generation of nanoporous materials meant for various high added value applications. The parallel emergence of controlled polymerization techniques has notably enabled to finely control their molecular features to confer them with unique structural and physicochemical properties, such as low dispersity values (Đ), well-defined volume fractions, and controlled functionality. The nanostructuration and ordering of diblock or triblock copolymers, which can be achieved through various experimental techniques, including channel die processing, solvent vapor or thermal annealing, nonsolvent-induced phase separation or concomitant self-assembly, and nonsolvent-induced phase separation, allows for the preparation of orientated microphase-separated copolymers whose morphology is dictated by three main factors, i.e., Flory-Huggins interaction parameter between constitutive blocks, volume fraction of the blocks, and polymerization degree. This review article provides an overview of the actual state of the art regarding the preparation of functional nanoporous materials from either diblock or triblock copolymers. It will also highlight the major applications of such peculiar materials.

Self-Assembly and In Situ Quaternization of Triblock Bottlebrush Block Copolymers via Organized Spontaneous Emulsification for Effective Loading of DNA

Microspheres bearing large pores are useful in the capture and separation of biomolecules. However, pore size is typically poorly controlled, leading to disordered porous structures with limited performances. Herein, ordered porous spheres with a layer of cations on the internal surface of the nanopores are facilely fabricated in a single step for effective loading of DNA bearing negative charges. Triblock bottlebrush copolymers (BBCPs), (polynorbornene-g-polystyrene)-b-(polynorbornene-g-polyethylene oxide)-b-(polynorbornene-g-bromoethane) (PNPS-b-PNPEO-b-PNBr), are designed and synthesized for fabrication of the positively charged porous spheres through self-assembly and in situ quaternization during an organized spontaneous emulsification (OSE) process. Pore diameter as well as charge density increase with the increase of PNBr content, resulting in a significant increase of loading density from 4.79 to 22.5 ng µg-1 within the spheres. This work provides a general strategy for efficient loading and encapsulation of DNA, which may be extended to a variety of different areas for different real applications.

Enhancing Water Treatment Performance of Porous Polysulfone Hollow Fiber Membranes through Atomic Layer Deposition

Polysulfone (PSF) is one of the most used polymers for water treatment membranes, but its intrinsic hydrophobicity can be detrimental to the membranes' performances. By modifying a membrane's surface, it is possible to adapt its physicochemical properties and thus tune the membrane's hydrophilicity or porosity, which can achieve improved permeability and antifouling efficiency. Atomic layer deposition (ALD) stands as a distinctive technology offering exceedingly even and uniform layers of coatings, like oxides that cover the surfaces of objects with three-dimensional (3D) shapes, porous structures, and particles. In the context of this study, the focus was on titanium dioxide (TiO2), zinc oxide (ZnO), and alumina (Al2O3), which were deposited on polysulfone hollow fiber (HF) membranes via ALD using TiCl4, diethyl zinc (DEZ), and trimethylamine (TMA), respectively, and H2O as precursors. The morphology and mechanical properties of membranes were changed without damaging their performances. The deposition was confirmed mainly by energy-dispersive X-ray spectroscopy (EDX). All depositions offered great performances with a maintained permeability and BSA retention and a 20 to 40° lower water contact angle (WCA) than the raw PSF HF membrane. The deposition of TiO2 offered the best results, showing an enhancement of 50% for the water permeability and 20% for the fouling resistance of the PSF HF membranes.

Advanced stimuli-responsive membranes for smart separation

Membranes have been extensively studied and applied in various fields owing to their high energy efficiency and small environmental impact. Further conferring membranes with stimuli responsiveness can allow them to dynamically tune their pore structure and/or surface properties for efficient separation performance. This review summarizes and discusses important developments and achievements in stimuli-responsive membranes. The most commonly utilized stimuli, including light, pH, temperature, ions, and electric and magnetic fields, are discussed in detail. Special attention is given to stimuli-responsive control of membrane pore structure (pore size and porosity/connectivity) and surface properties (wettability, surface topology, and surface charge), from the perspective of determining the appropriate membrane properties and microstructures. This review also focuses on strategies to prepare stimuli-responsive membranes, including blending, casting, polymerization, self-assembly, and electrospinning. Smart applications for separations are also reviewed as well as a discussion of remaining challenges and future prospects in this exciting field. This review offers critical insights for the membrane and broader materials science communities regarding the on-demand and dynamic control of membrane structures and properties. We hope that this review will inspire the design of novel stimuli-responsive membranes to promote sustainable development and make progress toward commercialization.

Non-Equilibrium Block Copolymer Self-Assembly Based Porous Membrane Formation Processes Employing Multicomponent Systems

Porous polymer-derived membranes are useful for applications ranging from filtration and separation technologies to energy storage and conversion. Combining block copolymer (BCP) self-assembly with the industrially scalable, non-equilibrium phase inversion technique (SNIPS) yields membranes comprising periodically ordered top surface structures supported by asymmetric, hierarchical substructures that together overcome performance tradeoffs typically faced by materials derived from equilibrium approaches. This review first reports on recent advances in understanding the top surface structural evolution of a model SNIPS-derived system during standard membrane formation. Subsequently, the application of SNIPS to multicomponent systems is described, enabling pore size modulation, chemical modification, and transformation to non-polymeric materials classes without compromising the structural features that define SNIPS membranes. Perspectives on future directions of both single-component and multicomponent membrane materials are provided. This points to a rich and fertile ground for the study of fundamental as well as applied problems using non-equilibrium-derived asymmetric porous materials with tunable chemistry, composition, and structure.

Supramolecular framework membrane for precise sieving of small molecules, nanoparticles and proteins

Synthetic framework materials have been cherished as appealing candidates for separation membranes in daily life and industry, while the challenges still remain in precise control of aperture distribution and separation threshold, mild processing methods, and extensive application aspects. Here, we show a two-dimensional (2D) processible supramolecular framework (SF) by integrating directional organic host-guest motifs and inorganic functional polyanionic clusters. The thickness and flexibility of the obtained 2D SFs are tuned by the solvent modulation to the interlayer interactions, and the optimized SFs with limited layers but micron-sized areas are used to fabricate the sustainable membranes. The uniform nanopores allow the membrane composed of layered SF to exhibit strict size retention for substrates with the rejection value of 3.8 nm, and the separation accuracy within 5 kDa for proteins. Furthermore, the membrane performs high charge selectivity for charged organics, nanoparticles, and proteins, due to the insertion of polyanionic clusters in the framework skeletons. This work displays the extensional separation potentials of self-assembled framework membranes comprising of small-molecules and provides a platform for the preparation of multifunctional framework materials due to the conveniently ionic exchange of the counterions of the polyanionic clusters.

A Separation-Sensing Platform Performing Accurate Diagnosis of Jaundice in Complex Biological Tear Fluids

The detection of biomarkers in tears has aroused great interest owing to the advantages of non-invasive and rapid collection. The combination of ultrasensitivity and label-free detection of surface-enhanced Raman spectroscopy (SERS) sensors is expected to achieve real-time diagnosis in home medical care. However, the surface of SERS sensors is susceptible to biofouling and inactivation by biological impurities in tears, resulting in rapid degradation of sensitivity, limiting the commercialization of point-of-care devices. Herein, a binary nanosphere array with dual properties is constructed as a separation-sensing platform for the diagnosis of target molecules in tears. The upper part of the structure is composed of Au nanoparticles (AuNPs) and a sputtering Au layer, which can bind the target molecules that interact with Au and provide high-strength and high-density SERS hotspots. The lower half is an inactive SiO₂ nanosphere array with periodic large pores that allows biological impurities to penetrate the lower part and be separated from the target analyte. Furthermore, this substrate was integrated into homemade tear kits, enabling simultaneous tear collection, pre-separation, and detection. Combined with the Raman spectra of tears and LDA analysis, we successfully identified patients with jaundice in clinics. This platform is expected to provide an opportunity for early disease screening based on biological fluids.

Solvent-assisted self-assembly of block copolymer thin films

Solvent-assisted block copolymer self-assembly is a compelling method for processing and advancing practical applications of these materials due to the exceptional level of the control of BCP morphology and significant acceleration of ordering kinetics. Despite substantial experimental and theoretical efforts devoted to understanding of solvent-assisted BCP film ordering, the development of a universal BCP patterning protocol remains elusive; possibly due to a multitude of factors which dictate the self-assembly scenario. The aim of this review is to aggregate both seminal reports and the latest progress in solvent-assisted directed self-assembly and to provide the reader with theoretical background, including the outline of BCP ordering thermodynamics and kinetics phenomena. We also indicate significant BCP research areas and emerging high-tech applications where solvent-assisted processing might play a dominant role.

DNA hydrogels as selective biomaterials for specifically capturing DNA, protein and bacteria

The ability to selectively capture biomacromolecules and other components from solution has many important applications in biotechnology. However, capturing targets from solution while minimizing interference with the sample solution is still challenging. Here, we describe the design and assembly of a group of DNA hydrogels consisting of long single-stranded DNA produced by rolling amplification reaction (RCA) and crosslinked by DNA duplexes. The developed DNA hydrogels can selectively capture and separate oligonucleotides, proteins and bacteria from solution in situ without complex separation processes. Since such DNA hydrogels can capture their targets in the solution independently, multiple DNA hydrogels that target different compounds can be employed to separate different compounds in the solution at the same time. The work not only expands the application of DNA hydrogels, but also paves the way for developing novel selective biomaterials. STATEMENT OF SIGNIFICANCE: Biomaterials capable of selectively capturing various components have great potential in the field of biotechnology. Here, we proposed a new class of hydrogel composed of crosslinked long DNA strands for selectively capturing DNA, protein and bacteria. Unlike traditional polymeric hydrogels that have small meshes and limit macromolecule diffusion owing to the short distance between two adjacent crosslinks, the described DNA hydrogel has a much larger distance between its crosslinks because of the sequence designability of DNA, which allows easy diffusion of biomacromolecules through its networks and greatly expand its specific surface area. Moreover, the developed DNA hydrogel can also easily combine different aptamers to target different components via the Watson-Crick base pairing without making significant changes in its original design.

Development of Novel Tetrapyrrole Structure Photosensitizers for Cancer Photodynamic Therapy

The effectiveness of photodynamic therapy (PDT) is based on the triad effects of photosensitizer (PS), molecular oxygen and visible light on malignant tumors. Such complex induces a multifactorial manner including reactive-oxygen-species-mediated damage and the killing of cells, vasculature damage of the tumor, and activation of the organism immunity. The effectiveness of PDT depends on the properties of photosensitizing drugs, their selectivity, enhanced photoproduction of reactive particles, absorption in the near infrared spectrum, and drug delivery strategies. Photosensitizers of the tetrapyrrole structure (porphyrins) are widely used in PDT because of their unique diagnostic and therapeutic functions. Nevertheless, the clinical use of the first-generation PS (sodium porfimer and hematoporphyrins) revealed difficulties, such as long-term skin photosensitivity, insufficient penetration into deep-seated tumors and incorrect localization to it. The second generation is based on different approaches of the synthesis and conjugation of porphyrin PS with biomolecules, which made it possible to approach the targeted PDT of tumors. Despite the fact that the development of the second-generation PS started about 30 years ago, these technologies are still in demand and are in intensive development, especially in the direction of improving the process of optimization split linkers responsive to input. Bioconjugation and encapsulation by targeting molecules are among the main strategies for developing of the PS synthesis. A targeted drug delivery system with the effect of increased permeability and retention by tumor cells is one of the ultimate goals of the synthesis of second-generation PS. This review presents porphyrin PS of various generations, discusses factors affecting cellular biodistribution and uptake, and indicates their role as diagnostic and therapeutic (theranostic) agents. New complexes based on porphyrin PS for photoimmunotherapy are presented, where specific antibodies are used that are chemically bound to PS, absorbing light from the near infrared part of the spectrum. Additionally, a two-photon photodynamic approach using third-generation photosensitizers for the treatment of tumors is discussed, which indicates the prospects for the further development of a promising method antitumor PDT.

Preparation of Small-Pore Ultrafiltration Membranes with High Surface Porosity by In Situ CO2 Nanobubble-Assisted NIPS

The fabrication of ultrafiltration (UF) membranes with a small pore size (<20 nm) and high surface porosity is still a great challenge. In this work, a nanobubble-assisted nonsolvent-induced phase separation (BNIPS) technique was developed to prepare high-performance UF membranes by adding a tiny amount of CaCO₃ nanoparticles into the casting solution. The phase inversion occurred in a dilute-acid coagulation bath to simultaneously generate CO₂ nanobubbles, which regulated the membrane structure. The effects of the nano-CaCO₃ content in the casting solution on the structure and performance of poly(ethersulfone)/sulfonated polysulfone (PES/SPSf) UF membranes were studied. The UF membrane prepared from a casting solution with 0.3% nano-CaCO₃ achieved a surface porosity of 12%, a pore diameter of 10.2 nm, and a skin-layer thickness of 80.3 nm. The superior structure of the UF membrane was mainly attributed to the in situ generation of CO₂ nanobubbles because the CO₂ nanobubbles were amphiphobic to water and solvents to delay the phase inversion time and acted as nanosize porogens. The produced membrane showed an unprecedented separation performance, achieving a pure water permeance of up to 1128 L·m^-2·h^-1·bar^-1, 2.5 fold that of the control membrane. Similarly, a high bovine serum albumin rejection of above 99.0% was obtained. The overall permeability and selectivity were better than those of commercial and other previously reported UF membranes. This work provides insight toward a simple and cost-effective technique to address the trade-off between pure water permeance and solute rejection of UF membranes.

Design of biointerfaces composed of soft materials using controlled radical polymerizations

Soft interface materials have an immense potential for the improvement of biointerfaces, which are the interface of biological and artificially designed materials. Controlling the chemical and physical structures of the interfaces at the nanometer level plays an important role in understanding the mechanism of the functioning and its applications. Controlled radical polymerization (CRP) techniques, including atom transfer radical polymerization (ATRP) and reversible addition-fragmentation chain-transfer (RAFT) polymerization, have been developed in the field of precision polymer chemistry. It allows the formation of well-defined surfaces such as densely packed polymer brushes and self-assembled nanostructures of block copolymers. More recently, a novel technique to prepare polymers containing biomolecules, called biohybrids, has also been developed, which is a consequence of the advancement of CRP so as to proceed in an aqueous media with oxygen. This review article summarizes recent advances in CRP for the design of biointerfaces.

Poly(vinylpyridine)-Containing Block Copolymers for Smart, Multicompartment Particles

Multicompartment particles generated by the self-assembly of block copolymers (BCPs) have received considerable attention due to their unique morphologies and functionalities. A class of important building blocks for multicomponent particles...

Hybrid Organic-Inorganic-Organic Isoporous Membranes with Tunable Pore Sizes and Functionalities for Molecular Separation

Accomplishing on-demand molecular separation with a high selectivity and good permeability is very desirable for pollutant removal and chemical and pharmaceutical processing. The major challenge for sub-10 nm filtration of particles and molecules is the fabrication of high-performance membranes with tunable pore size and designed functionality. Here, a versatile top-down approach is demonstrated to produce such a membrane using isoporous block copolymer membranes with well-defined pore sizes combined with growth of metal oxide using sequential infiltration synthesis and atomic layer deposition (SIS and ALD). The pore size of the membranes is tuned by controlled metal oxide growth within and onto the polymer channels, enabling up to twofold pore diameter reduction. Following the growth, the distinct functionalities are readily incorporated along the membrane nanochannels with either hydrophobic, cationic, or anionic groups via straightforward and scalable gas/liquid-solid interface reactions. The hydrophilicity/hydrophobicity of the membrane nanochannel is significantly changed by the introduction of hydrophilic metal oxide and hydrophobic fluorinated groups. The functionalized membranes exhibit a superior selectivity and permeability in separating 1-2 nm organic molecules and fractionating similar-sized proteins based on size, charge, and hydrophobicity. This demonstrates the great potential of organic-inorganic-organic isoporous membranes for high-performance molecular separation in numerous applications.

Asymmetric Solvent-Annealed Triblock Terpolymer Thick Films Topped by a Hexagonal Perforated Lamellar Nanostructure

Asymmetric and nanostructured polystyrene-block-poly(2-vinyl pyridine)-block-poly(ethylene oxide) (PS-b-P2VP-b-PEO or SVEO, S:V:EO ≈ 56:34:10, 79.5 kg mol^-1 ) thick films blended with 20 wt% of a short PS homopolymer (hPS, 10.5 kg mol^-1 ) are achieved by combining the non-solvent induced phase separation (NIPS) process with a solvent vapor annealing (SVA) treatment. Here, the NIPS step allows for the formation of a highly-permeable sponge-like substructure topped by a dense thin layer exhibiting poorly-ordered nanopores while the subsequent SVA treatment enables to reconstruct the material top surface into a porous monolayer of well-ordered hexagonal perforated lamellae (HPL). This optimized film architecture generated by NIPS-SVA shows a water permeability of 860 L h^-1 m^-2 bar^-1 , which is roughly two times higher than the flux measured through NIPS made PS-b-P2VP-b-PEO/hPS materials having poorly-ordered nanopores. The post-SVA treatment is also revealed as a powerful tool to tailor the thickness of the nanostructure formed within the blended material because monoliths entirely composed of a HPL phase are produced by increasing the time of exposure to a chloroform stream. The water flux of such PS-b-P2VP-b-PEO/hPS monoliths is found to be an order of magnitude lower than that of their asymmetric film homologues.

Actively Controllable Solid-Phase Microextraction in a Hierarchically Organized Block Copolymer-Nanopore Electrode Array Sensor for Charge-Selective Detection of Bacterial Metabolites

Pseudomonas aeruginosa produces a number of phenazine metabolites, including pyocyanin (PYO), phenazine-1-carboxamide (PCN), and phenazine-1-carboxylic acid (PCA). Among these, PYO has been most widely studied as a biomarker of P. aeruginosa infection. However, despite its broad-spectrum antibiotic properties and its role as a precursor in the biosynthetic route leading to other secondary phenazines, PCA has attracted less attention, partially due to its relatively low concentration and interference from other highly abundant phenazines. This challenge is addressed here by constructing a hierarchically organized nanostructure consisting of a pH-responsive block copolymer (BCP) membrane with nanopore electrode arrays (NEAs) filled with gold nanoparticles (AuNPs) to separate and detect PCA in bacterial environments. The BCP@NEA strategy is designed such that adjusting the pH of the bacterial medium to 4.5, which is above the pK_a of PCA but below the pK_a of PYO and PCN, ensures that PCA is negatively charged and can be selectively transported across the BCP membrane. At pH 4.5, only PCA is transported into the AuNP-filled NEAs, while PYO and PCN are blocked. Structural characterization illustrates the rigorous spatial segregation of the AuNPs in the NEA nanopore volume, allowing PCA secreted from P. aeruginosa to be quantitatively determined as a function of incubation time using square-wave voltammetry and surface-enhanced Raman spectroscopy. The strategy proposed in this study can be extended by changing the nature of the hydrophilic block and subsequently applied to detect other redox-active metabolites at a low concentration in complex biological samples and, thus, help understand metabolism in microbial communities.

Polyelectrolytes as Building Blocks for Next-Generation Membranes with Advanced Functionalities

The global society is in a transition, where dealing with climate change and water scarcity are important challenges. More efficient separations of chemical species are essential to reduce energy consumption and to provide more reliable access to clean water. Here, membranes with advanced functionalities that go beyond standard separation properties can play a key role. This includes relevant functionalities, such as stimuli-responsiveness, fouling control, stability, specific selectivity, sustainability, and antimicrobial activity. Polyelectrolytes and their complexes are an especially promising system to provide advanced membrane functionalities. Here, we have reviewed recent work where advanced membrane properties stem directly from the material properties provided by polyelectrolytes. This work highlights the versatility of polyelectrolyte-based membrane modifications, where polyelectrolytes are not only applied as single layers, including brushes, but also as more complex polyelectrolyte multilayers on both porous membrane supports and dense membranes. Moreover, free-standing membranes can also be produced completely from aqueous polyelectrolyte solutions allowing much more sustainable approaches to membrane fabrication. The Review demonstrates the promise that polyelectrolytes and their complexes hold for next-generation membranes with advanced properties, while it also provides a clear outlook on the future of this promising field.

Unusual Nanofractal Microparticles for Rapid Protein Capture and Release

Ion exchange porous microparticles are widely used for protein separation, but their totally porous structure often leads to slow diffusion rate and long separation time. Here unusual nanofractal microparticles synthesized by a strategy of electrostatic interaction regulated emulsion interfacial polymerization are demonstrated that exhibit excellent capability of rapid protein capture, release, and separation. The growth of nanostructures at nanofractal microparticle surface can be controlled by changing electrostatic repulsion between ion groups from weak to strong. The nanofractal microparticles provide a 3D contact model between ion groups and proteins, enable fast protein diffusion rate at initial capture and release stage, and realize rapid and efficient separation of similarly sized proteins as a proof of concept, superior to porous microparticles. This strategy offers an effective and general way for the synthesis of microparticles towards rapid and efficient separation in various fields of biomedicine, environment, and food.

Understanding nanodomain morphology formation in dip-coated PS-b-PEO thin films

Block copolymer (BCP) thin films prepared by dip-coating are increasingly investigated, owing to the many promising application areas, the facility, and the industrial scalability of this technique. Yet, the effect of different dip-coating parameters on BCP nanostructure formation is still underdeveloped and the results of previous literature are limited to a few block copolymers. Here, we study the effect of the withdrawal rate and solvent selectivity on the morphology evolution of dip-coated polystyrene-b-poly(ethylene oxide) thin films by applying a wide range of dip-coating speeds and altering the volume ratio of the tetrahydrofuran-water solvent system. The dip-coated films were characterized using atomic force microscopy and ellipsometry. The nanodomain morphology, its feature sizes, its spanning, and the degree of ordering were investigated with regard to different dip-coating parameters. Notably, we have obtained a hexagonally packed BCP pattern with long-range order without the need for post-annealing processes. Overall, a solid understanding of the parameters affecting the formed surface patterns and their interplay was attained and explained, extending the knowledge of this field to more materials.

Developing Anisotropy in Self-Assembled Block Copolymers: Methods, Properties, and Applications

Block copolymers (BCPs) self-assembly has continually attracted interest as a means to provide bottom-up control over nanostructures. While various methods have been demonstrated for efficiently ordering BCP nanodomains, most of them do not generically afford control of nanostructural orientation. For many applications of BCPs, such as energy storage, microelectronics, and separation membranes, alignment of nanodomains is a key requirement for enabling their practical use or enhancing materials performance. This review focuses on summarizing research progress on the development of anisotropy in BCP systems, covering a variety of topics from established aligning techniques, resultant material properties, and the associated applications. Specifically, the significance of aligning nanostructures and the anisotropic properties of BCPs is discussed and highlighted by demonstrating a few promising applications. Finally, the challenges and outlook are presented to further implement aligned BCPs into practical nanotechnological applications, where exciting opportunities exist.

Selective Adsorption and Separation of Proteins by Ligand-Modified Nanofiber Fabric

Electrospun polyvinyl alcohol (PVA) nanofiber fabric was modified by Cibacron Blue F3GA (CB) to enhance the affinity of the fabric. Batch experiments were performed to study the nanofiber fabric's bovine hemoglobin (BHb) adsorption capacity at different protein concentrations before and after modification. The maximum BHb adsorption capacity of the modified nanofiber fabric was 686 mg/g, which was much larger than the 58 mg/g of the original fabric. After that, the effect of feed concentration and permeation rate on the dynamic adsorption behaviors for BHb of the nanofiber fabric was investigated. The pH impact on BHb and bovine serum albumin (BSA) adsorption was examined by static adsorption experiments of single protein solutions. The selective separation experiments of the BHb-BSA binary solution were carried out at the optimal pH value, and a high selectivity factor of 5.45 for BHb was achieved. Finally, the reusability of the nanofiber fabric was examined using three adsorption-elution cycle tests. This research demonstrated the potential of the CB-modified PVA nanofiber fabric in protein adsorption and selective separation.

Porous polymeric membranes: fabrication techniques and biomedical applications

Porous polymeric membranes have shown great potential in biological and biomedical applications such as tissue engineering, bioseparation, and biosensing, due to their structural flexibility, versatile surface chemistry, and biocompatibility. This review outlines the advantages and limitations of the fabrication techniques commonly used to produce porous polymeric membranes, with especial focus on those featuring nano/submicron scale pores, which include track etching, nanoimprinting, block-copolymer self-assembly, and electrospinning. Recent advances in membrane technology have been key to facilitate precise control of pore size, shape, density and surface properties. The review provides a critical overview of the main biological and biomedical applications of these porous polymeric membranes, especially focusing on drug delivery, tissue engineering, biosensing, and bioseparation. The effect of the membrane material and pore morphology on the role of the membranes for each specific application as well as the specific fabrication challenges, and future prospects of these membranes are thoroughly discussed.

Tunable Pore Size from Sub-Nanometer to a Few Nanometers in Large-Area Graphene Nanoporous Atomically Thin Membranes

Membranes are key components in chemical purification, biological separation, and water desalination. Traditional polymeric membranes are subjected to a ubiquitous trade-off between permeance and selectivity, which significantly hinders the separation performance. Nanoporous atomically thin membranes (NATMs), such as graphene NATMs, have the potential to break this trade-off. Owing to their uniqueness of two-dimensional structure and potential nanopore structure controllability, NATMs are expected to have outstanding selectivity through molecular sieving while achieving ultimate permeance at the same time. However, a drastic selectivity discrepancy exists between the proof-of-concept demonstrations and scalable separation applications in graphene membranes. In this paper, we offer a possible solution to narrow this discrepancy by tuning the pore density and pore size separately with two successive plasma treatments. We demonstrate that by narrowing the pore size distribution, the selectivity of graphene membranes can be greatly increased. Low-energy argon plasma is first applied to nucleate high density of defects in graphene. Controlled oxygen plasma is then utilized to selectively enlarge the defects into nanopores with desired sizes. This method is scalable, and the fabricated 1 cm2 graphene NATMs with sub-nanometer pores can separate KCl and Allura Red with a selectivity of 104 and a permeance of 1.1 × 10-6 m s-1. The pores in NATMs can be further tuned from gas-selective sub-nanometer pores to a few nanometer size. The fabricated NATMs show a selectivity of 35 between CO2 and N2. With longer enlargement time, a selectivity of 21.2 between a lysozyme and bovine serum albumin can also be achieved with roughly four times higher permeance than that of a commercial dialysis membrane. This research offers a solution to realize NATMs of tunable pore size with a narrow pore size distribution for different separation processes from sub-nanometer in gas separation or desalination to a few nanometers in dialysis.

Porous block copolymer separation membranes for 21st century sanitation and hygiene

Removing hazardous particulate and macromolecular contaminants as well as viruses with sizes from a few nm up to the 100 nm-range from water and air is crucial for ensuring sufficient sanitation and hygiene for a growing world population. To this end, high-performance separation membranes are needed that combine high permeance, high selectivity and sufficient mechanical stability under operating conditions. However, design features of separation membranes enhancing permeance reduce selectivity and vice versa. Membrane configurations combining high permeance and high selectivity suffer in turn from a lack of mechanical robustness. These problems may be tackled by using block copolymers (BCPs) as a material platform for the design of separation membranes. BCPs are macromolecules that consist of two or more chemically distinct block segments, which undergo microphase separation yielding a wealth of ordered nanoscopic domain structures. Various methods allow the transformation of these nanoscopic domain structures into customized nanopore systems with pore sizes in the sub-100 nm range and with narrow pore size distributions. This tutorial review summarizes design strategies for nanoporous state-of-the-art BCP separation membranes, their preparation, their device integration and their use for water purification.

Selective Swelling and Functionalization of Integral Asymmetric Isoporous Block Copolymer Membranes

SNIPS stands for a membrane fabrication technique that combines the evaporation induced self-assembly of the block copolymers and the classical nonsolvent induced phase separation. It is a one-step readily scalable technique to fabricate integral asymmetric isoporous membranes. The prominent developments in the last decade have carved out a niche for SNIPS as a potential technique to fabricate next generation isoporous membranes. In the last decade, a rich polymer library and variety of membrane postmodification routes have been successfully implemented to fabricate SNIPS membranes having the desired pore functionality. Some of these membranes form soft nanochannels in hydrated state due to swelling of the pore wall, i.e., the pore forming block of the block copolymer. These membranes having soft nanochannels have demonstrated the potential to perform several challenging separation tasks in ultrafiltration and nanofiltration. This paper highlights the currently accessible pore functionality, the strategies to tune the swelling of the soft nanochannels, the potential applications, and future perspectives of these membranes.

Direct Access to Bowl-Like Nanostructures with Block Copolymer Anisotropic Truncated Microspheres

Bowl-like nanostructures have attracted significant scientific and technological interest due to their favorable characteristics, such as high specific surface area, interconnected porous channels, and conductivity. However, tailored synthesis of bowl-like nanostructures with well-defined and uniform morphology is still a challenge. Herein, we report a versatile microemulsion assembly approach to prepare bowl-like nanostructures of three different materials: polymer, carbon, and platinum. To this end, polystyrene-block-poly(4vinylpyridine), PS-b-P4VP, block copolymer (BCP) microparticles with truncated-sphere shape and composed of stacks of parallel lamellae were used because those anisotropic microparticles play an important role in the design of bowl-like nanostructures. To form nanolamellae-within-microparticle morphology, a designed PS-b-P4VP/chloroform/CTAB microemulsion can be facilely obtained in the aqueous medium, where the morphology can be tailored by the interplay between macro-phase separations, BCP self-assembly, and interfacial energies of three phases in the presence of cetyltrimethylammonium bromide (CTAB). Finally, protonation or combination of cross-linking and pyrolysis of those truncated microparticles enables formation of polymer or carbon bowl-like nanostructures, respectively. Upon selective adsorption of Pt precursor salt ions with the pyridyl moieties followed by chemical reduction, subsequent calcination permits the synthesis of Pt bowl-like nanostructures. The microemulsion assembly approach opens up new ways to direct and template bowl-like nanostructures.

Ion Gating in Nanopore Electrode Arrays with Hierarchically Organized pH-Responsive Block Copolymer Membranes

Inspired by biological ion channels, artificial nanopore-based architectures have been developed for smart ion/molecular transport control with potential applications to iontronics and energy conversion. Advances in nanofabrication technology enable simple, versatile construction methods, and post-fabrication functionalization delivers nanochannels with unique ion transport-control attributes. Here, we characterize a pH-responsive, charge-selective dual-gating block copolymer (BCP) membrane composed of polystyrene-b-poly(4-vinylpyridine) (PS₄₈₄₀₀-b-P4VP₂₁₃₀₀), capable of self-organizing into highly ordered nanocylindrical domains. Because the PS-b-P4VP membrane exhibits pH-dependent structural transitions, it is suitable for designing intelligent pH-gated biomimetic channels, for example, exhibiting on-off transport switching at pH values near the pK_a of P4VP with excellent anion permselectivity at pH < pK_a. Introducing the BCP membrane onto nanopore electrode arrays (BCP@NEAs) allows the BCP to serve as a pH-responsive gate controlling ion transfer into the NEA nanopores. Such selectively transported and confined ions are detected by using a 100 nm gap dual-ring nanoelectrode structure capable of enhancing current output by efficient redox cycling with an amplification factor >10². In addition, BCP@NEAs exhibit extraordinary pH-gated ion selectivity, resulting in a 3380-fold current difference between anion and cation probes at pH 3.0. This hierarchically organized BCP-gated NEA system can serve as a template for the development of other stimulus-responsive ion gates, for example, those based on temperature and ligand gating, thus exploiting the intrinsic advantages of NEAs, such as enhanced sensitivity based on redox cycling, which may lead to technological applications such as engineered biosensors and iontronic devices.