Clean energy and the hydrogen economy

Thin Film TaFe, TaCo, and TaNi as Potential Optical Hydrogen Sensing Materials

This paper studies the structural and optical properties of tantalum-iron-, tantalum-cobalt-, and tantalum-nickel-sputtered thin films both ex situ and while being exposed to various hydrogen pressures/concentrations, with a focus on optical hydrogen sensing applications. Optical hydrogen sensors require sensing materials that absorb hydrogen when exposed to a hydrogen-containing environment. In turn, the absorption of hydrogen causes a change in the optical properties that can be used to create a sensor. Here, we take tantalum as a starting material and alloy it with Fe, Co, or Ni with the aim to tune the optical hydrogen sensing properties. The rationale is that alloying with a smaller element would compress the unit cell, reduce the amount of hydrogen absorbed, and shift the pressure composition isotherm to higher pressures. X-ray diffraction shows that no lattice compression is realized for the crystalline Ta body-centered cubic phase when Ta is alloyed with Fe, Co, or Ni, but that phase segregation occurs where the crystalline body-centered cubic phase coexists with another phase, as for example an X-ray amorphous one or fine-grained intermetallic compounds. The fraction of this phase increases with increasing alloyant concentration up until the point that no more body-centered cubic phase is observed for 20% alloyant concentration. Neutron reflectometry indicates only a limited reduction of the hydrogen content with alloying. As such, the ability to tune the sensing performance of these materials by alloying with Fe, Co, and/or Ni is relatively small and less effective than substitution with previously studied Pd or Ru, which do allow for a tuning of the size of the unit cell, and consequently tunable hydrogen sensing properties. Despite this, optical transmission measurements show that a reversible, stable, and hysteresis-free optical response to hydrogen is achieved over a wide range of hydrogen pressures/concentrations for Ta-Fe, Ta-Co, or Ta-Ni alloys which would allow them to be used in optical hydrogen sensors.

Biohydrogen generation from distillery effluent using baffled up-flow microbial electrolysis cell

Microbial electrolysis cell (MEC) is gaining importance not only for effectively treating wastewater but also for producing hydrogen. The up-flow microbial electrolysis cell (UPMEC) is an innovative approach to enhance the efficiency, and substrate degradation. In this study, a baffled UPMEC with an anode divided into three regions by inserting the baffle (sieve) plates at varying distances from the cathode was designed. The effect of process parameters, such as flow rate (10, 15, and 20 mL/min), electrode area (50, 100, and 150 cm2), and catholyte buffer concentration (50, 100, and 150 mM) were investigated using distillery wastewater as substrate. The experimental results showed a maximum of 0.6837 ± 0.02 mmol/L biohydrogen at 150 mM buffer, with 49 ± 1.0% COD reduction using an electrode of area 150 cm2. The maximum current density was 1335.94 mA/m2 for the flow rate of 15 mL/min and surface area of 150 cm2. The results showed that at optimized flow rate and buffer concentration, maximum hydrogen production and effective treatment of wastewater were achieved in the baffled UPMEC. PRACTITIONER POINTS: Biohydrogen production from distillery wastewater was investigated in a baffled UPMEC. Flowrate, concentration and electrode areas significantly influenced the hydrogen production. Maximum hydrogen (0.6837±0.02mmol/L.day) production and COD reduction (49±1.0%) was achieved at 15 mL/min. Highest CHR of 95.37±1.9 % and OHR of 4.6±0.09 % was observed at 150 mM buffer concentration.

Insights into the nucleation and growth of BiOCl nanoparticles by in situ X-ray pair distribution function analysis and in situ liquid cell TEM

The synthesis of bismuth oxyhalides as defined nanostructures is hindered by their fast nucleation and growth in aqueous solutions. Using our recently developed single-source precursor, the formation of bismuth oxychloride in such solutions can be slowed significantly. As reported herein, this advance enables BiOCl formation to be investigated by in situ X-ray total scattering and in situ liquid cell transmission electron microscopy. In situ pair distribution function analysis of X-ray total scattering data reveals the local order of atomic structures throughout the synthesis, while in situ liquid cell transmission electron microscopy allows for tracking the growth of individual nanoparticles. Through this work, the precursor complex is shown to give rise to BiOCl upon heating in solution without the observation of structurally distinct intermediates. The emerging nanoparticles have a widened interlayer spacing, which moderately decreases as the particles grow. Mechanistic insights into the formation of bismuth oxyhalide nanoparticles, including the absence of distinct intermediates within the available time resolution, will help facilitate future design of controlled BiOX nanostructures.

Recent Development of Physical Hydrogen Storage: Insights into Global Outlook and Future Applications

Transition of global energy market towards an environment-friendly sustainable society requires a profound transformation from fossil fuel to zero carbon emission fuel. To cope with this goal production ofrenewable energy is accelerating worldwide. Research in renewable energy from production and storage to practical utilization requires an organized approach. One of the best renewable energy carrier is the hydrogen, due to its clean combustion and abundance. Nonetheless, its storage is a critical challenge to its success. Hydrogen must be stored long after being produced and transported to a storage site. Physical hydrogen storage is vital among hydrogen storage modes, and its shortcoming needs to overcome for its successful and economic benefits. This review intends to discuss the techniques and applications of physical hydrogen storage in the state of compressed gas, liquefied hydrogen gas, and cold/cryo compressed gas concerning their working principle, chemical and physical properties, influencing factors for physical hydrogen storage, and transportation, economics, and global outlook. Insights of several probable physical hydrogen storage (PHS) systems are highlighted. The outcomes of this review envisioned that the PHS still necessitates technological advancements despite having remarkable success. The Liquid Hydrogen Gas storage marks better sustainability than Compressed and Cryo Compressed Gas. The physical hydrogen storage method can store hydrogen in tanks in any state (liquid or gas) under 20 K for the liquid state and ambient temperature for the gaseous state The Bibliographic analysis depicts that the research in hydrogen rising with time and mostly the research in conducted in USA with 231 articles. Prospects and challenges with lessons learned and the limitation opens the door to further research, which would be helpful for efficient and long-term physical hydrogen storage.

State-of-the-art review on hydrogen's production, storage, and potential as a future transportation fuel

Global energy consumption is expected to reach 911 BTU by the end of 2050 as a result of rapid urbanization and industrialization. Hydrogen is increasingly recognized as a clean and reliable energy vector for decarbonization and defossilization across various sectors. Projections indicate a significant rise in global demand for hydrogen, underscoring the need for sustainable production, efficient storage, and utilization. In this state-of-the-art review, we explore hydrogen production methods, compare their environmental impacts through life cycle analysis, delve into geological storage options, and discuss hydrogen's potential as a future transportation fuel. Combining electrolysis to make hydrogen and storing it in porous underground materials like salt caverns and geological reservoirs looks like a good way to balance out the variable supply of renewable energy and meet the demand at peak times. Hydrogen is a key component of our sustainable economy, and this article gives a broad overview of the process from production to consumption, touching on technical, economic, and environmental concerns along the way. We have made an attempt in this paper to compile different methods for the production of hydrogen and its storage, the challenges faced by current methods in the manufacturing of hydrogen gas, and the role of hydrogen in the future. This review paper will serve as a very good reference for hydrogen system engineering applications. The paper concludes with some suggestions for future research to help improve the technological efficiency of certain production methods, all with the goal of scaling up the hydrogen economy.

A comprehensive review on unleashing the power of hydrogen: revolutionizing energy systems for a sustainable future

Population growth and environmental degradation are major concerns for sustainable development worldwide. Hydrogen is a clean and eco-friendly alternative to fossil fuels, with a heating value almost three times higher than other fossil fuels. It also has a clean production process, which helps to reduce the emission of hazardous pollutants and save the environment. Among the various production methodologies described in this review, biochemical production of hydrogen is considered more suitable as it uses waste organic matter instead of fossil fuels. This technology not only produces clean energy but also helps to manage waste more efficiently. However, the production of hydrogen obtained from this method is currently more expensive due to its early stage of development. Nevertheless, various research projects are underway to develop this method on a commercial scale.

Performance Enhancement of Electrocatalytic Hydrogen Evolution through Coalescence-Induced Bubble Dynamics

The evolution of electrogenerated gas bubbles during water electrolysis can significantly hamper the overall process efficiency. Promoting the departure of electrochemically generated bubbles during (water) electrolysis is therefore beneficial. For a single bubble, a departure from the electrode surface occurs when buoyancy wins over the downward-acting forces (e.g., contact, Marangoni, and electric forces). In this work, the dynamics of a pair of H2 bubbles produced during the hydrogen evolution reaction in 0.5 M H2SO4 using a dual platinum microelectrode system is systematically studied by varying the electrode distance and the cathodic potential. By combining high-speed imaging and electrochemical analysis, we demonstrate the importance of bubble-bubble interactions in the departure process. We show that bubble coalescence may lead to substantially earlier bubble departure as compared to buoyancy effects alone, resulting in considerably higher reaction rates at a constant potential. However, due to continued mass input and conservation of momentum, repeated coalescence events with bubbles close to the electrode may drive departed bubbles back to the surface beyond a critical current, which increases with the electrode spacing. The latter leads to the resumption of bubble growth near the electrode surface, followed by buoyancy-driven departure. While less favorable at small electrode spacing, this configuration proves to be very beneficial at larger separations, increasing the mean current up to 2.4 times compared to a single electrode under the conditions explored in this study.

Bifunctional porphyrin-based metal-organic polymers for electrochemical water splitting

Electrochemical water splitting offers the potential for environmentally friendly hydrogen and oxygen gas generation. Here, we present the synthesis, characterization, and electrochemical analyses of four organic polymers where metalloporphyrins are the active center nodes. These materials were obtained from the polymerization reaction of poly(p-phenylene terephtalamide) (PPTA) with the respective amino-functionalized metalloporphyrins, where M = Fe, 1; Co, 2; Ni, 3; Cu, 4. Scanning and transmission electron microscopy images (SEM and TEM) show that these polymers exhibit a layer-type morphology, which is attributed to hydrogen bonding and π-π stacking between the metalloporphyrin nodes. The synthesized materials were characterized by X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), UV-Vis spectroscopy, and Fourier-transform infrared spectroscopy (FT-IR). Among the materials studied, the cobalt-based polymer, 2, demonstrates a bifunctional electrocatalytic activity for oxygen (OER) and hydrogen (HER) evolution reactions with overpotentials (η10) of 337 mV and 435 mV, respectively. The Fe, 1, and Ni, 2, polymers are less active for HER with maximum current densities (jmax) of 12.6 and 19.1 mA cm-2 and η10 678 mV, 644 mV. Polymer 2 achieves a jmax of 37.7 mA cm-2 for HER and 133 mA cm-2 for OER. The copper-based material, 4, on the other hand, shows selectivity towards HER with an overpotential (η) of 436 mV and a maximum current density (j) of 45.5 mA cm-2. The bifunctional electrocatalytic performance was tested in the overall water-splitting setup, where polymer 2 requires a cell voltage of 1.64 V at 10 mA cm-2. This work presents a novel approach to heterogenized molecular systems, providing materials with exceptional structural characteristics and enhanced electrocatalytic capabilities.

Emerging trends of green hydrogen and sustainable environment in the case of Australia

The world faces immense pressure regarding the negative impacts of increased greenhouse gas emissions, climate change, global warming, droughts, and many other environmental problems. Australia is also facing the same issues and requires urgent attention. In this research, we have examined the effect of hydrogen firms on Australia's greenhouse gas emissions. We employed the monthly data from January 2002 to December 2021 for econometric estimations. Through quantile regression, it is noted that the expansion of hydrogen firms contributes to environmental pollution instead of controlling the emissions. Most hydrogen energy still emits carbon dioxide, which contributes to climate change. Around the world, carbon-containing fossil fuels produce more than 95% of hydrogen energy. However, as a policy suggestion, it is recommended that green hydrogen produced by electrolysis of water using renewable energy sources will succeed in achieving the Sustainable Development Goals (SDGs).

Radical-Mediated Photocatalysis for Lignocellulosic Biomass Conversion into Value-Added Chemicals and Hydrogen: Facts, Opportunities and Challenges

Photocatalytic biomass conversion into high-value chemicals and fuels is considered one of the hottest ongoing research and industrial topics toward sustainable development. In short, this process can cleave Cβ -O/Cα -Cβ bonds in lignin to aromatic platform chemicals, and further conversion of the polysaccharides to other platform chemicals and H2 . From the chemistry point of view, the optimization of the unique cooperative interplay of radical oxidation species (which are activated via molecular oxygen species, ROSs) and substrate-derived radical intermediates by appropriate control of their type and/or yield is key to the selective production of desired products. Technically, several challenges have been raised that face successful real-world applications. This review aims to discuss the recently reported mechanistic pathways toward selective biomass conversion through the optimization of ROSs behavior and materials/system design. On top of that, through a SWOT analysis, we critically discussed this technology from both chemistry and technological viewpoints to help the scientists and engineers bridge the gap between lab-scale and large-scale production.

Good Practices and Limitations of the Hydrogen Pump Technique for Catalyst Layer Protonic Conductivity Estimation

The hydrogen pump technique has been shown to be an effective method to measure the effective protonic conductivity of intermediate layers (ILs) that mimic the catalyst layers used in proton exchange membrane fuel cells and electrolyzers. It has been hypothesized, however, that the technique is limited to testing ILs that are inactive during the hydrogen reaction as proton transport through the ionomer in the layer can be bypassed by transferring the charge to the electronic phase via the reaction. This work uses numerical modeling, supported by experimental testing, to investigate the impact of IL hydrogen reaction activity, thickness, and electronic conductivity on the prediction of the IL protonic conductivity. A transient, 2-D, through-the-channel model is developed and implemented using the finite element method to predict the performance of hydrogen pump cells and perform electrochemical impedance spectroscopy. It is shown both numerically and experimentally that for iridium black and for platinum-/carbon-based ILs, the protonic phase is almost entirely bypassed, reducing the overall cell resistance and making the determination of the true conductivity difficult. The model can be used to provide an estimate of the resistance of the active layers, which is not possible using only experiments. In addition, the interfacial contact resistance between the membrane and the catalyst layers is determined using the high-frequency resistance, and the alternating current method for the hydrogen pump is studied to determine the accuracy of the method. Finally, further insights are provided through a breakdown of the resistances of each phase, as well as the potential profiles, in an active IL, and through parametric studies on the impact of varying the IL activity, thickness, and electronic conductivity.

Hydrogen and helium trapping in hcp beryllium

Even though hydrogen-metal surface interactions play an important role in energy technologies and metal corrosion, a thorough understanding of these interactions at the nanoscale remains elusive due to obstructive detection limits in instrumentation and the volatility of pure hydrogen. In the present paper we use analytical spectroscopy in TEM to show that hydrogen adsorbs directly at the (0001) surfaces of hexagonal helium bubbles within neutron irradiated beryllium. In addition to hydrogen, we also found Al, Si and Mg at the beryllium-bubble interfaces. The strong attraction of these elements to (0001) surfaces is underlined with ab-initio calculations. In situ TEM heating experiments reveal that hydrogen can desorb from the bubble walls at T ≥ 400 °C if the helium content is reduced by opening the bubbles. Based on our results we suggest the formation of a complex hydride consisting of up to five elements with a remarkably high decomposition temperature. These results therefore promise novel insights into metal-hydrogen interaction behavior and are invaluable for the safety of future fusion power plants.

Cu2O-Cu@Titanium Surface with Synergistic Performance for Nitrate-to-Ammonia Electrochemical Reduction

Transition metals, such as titanium (Ti) and copper (Cu) along with their respective metal oxides (TiO₂, Cu₂O, and CuO), have been widely studied as electrocatalysts for nitrate electrochemical reduction with important outcomes in the fields of denitrification and ammonia generation. Based on this, this work conducted an evaluation of a composite electrode that integrates materials with different intrinsic activities (i.e., Cu and Cu₂O for higher activity for nitrate conversion; Ti for higher faradaic efficiency to ammonia) looking for potential synergistic effects in the direction of ammonia generation. The specific performance of single-metal and composite electrodes has shown a strong dependence on pH and nitrate concentration conditions. Faradaic efficiency to ammonia of 92% and productivities of 0.28 mmol_NH3 ·cm^-2·h^-1 at 0.5 V vs reversible hydrogen electrode (RHE) values are achieved, demonstrating the implicit potential of this approach in comparison to direct N₂RR with values in the order of μmol_NH3 ·h^-1·cm^-2. Finally, the electrochemical rate constants (k) for Ti, Cu, and Cu₂O-Cu/Ti disk electrodes were determined by the Koutecky-Levich analysis with a rotating disk electrode (RDE) in 3.02 × 10^-6, 3.88 × 10^-4, and 4.77 × 10^-4 cm·s^-1 demonstrating an apparent synergistic effect for selective NiRR to ammonia with a Cu₂O-Cu/Ti electrode.

Halophilic CO2-fixing microbial community as biocatalyst improves the energy efficiency of the microbial electrosynthesis process

Using saline electrolytes in combination with halophilic CO₂-fixing lithotrophic microbial catalysts has been envisioned as a promising strategy to develop an energy-efficient microbial electrosynthesis (MES) process for CO₂ utilization. Here, an enriched marine CO₂-fixing lithotrophic microbial community dominated by Vibrio and Clostridium spp. was tested for MES of organic acids from CO₂. At an applied E_cathode of -1V (vs Ag/AgCl) with 3.5 % salinity (78 mScm^-1), it produced 379 ± 53 mg/L (6.31 ± 0.89 mM) acetic acid and 187 ± 43 mg/L (4.05 ± 0.94 mM) formic acid at 2.1 ± 0.30 and 1.35 ± 0.31 mM day^-1, respectively production rates. Most electrons were recovered in acetate (68.3 ± 3 %), formate (9.6 ± 1.2 %) besides hydrogen (11 ± 1.4 %) and biomass (8.9 ± 1.65 %). Notably, the bioproduction of organic acids occurred at a high energetic efficiency (EE) of ∼ 46 % and low E_cell of 2.3 V in saline conditions compared to the commonly used non-saline electrolytes (0.5-1 mScm^-1) in the reported MES studies with CO₂ (E_cell: >2.5 V and EE: <34 %).

Tuning the Properties of Thin-Film TaRu for Hydrogen-Sensing Applications

Accurate, cost-efficient, and safe hydrogen sensors will play a key role in the future hydrogen economy. Optical hydrogen sensors based on metal hydrides are attractive owing to their small size and costs and the fact that they are intrinsically safe. These sensors rely on suitable sensing materials, of which the optical properties change when they absorb hydrogen if they are in contact with a hydrogen-containing environment. Here, we illustrate how we can use alloying to tune the properties of hydrogen-sensing materials by considering thin films consisting of tantalum doped with ruthenium. Using a combination of optical transmission measurements, ex situ and in situ X-ray diffraction, and neutron and X-ray reflectometry, we show that introducing Ru in Ta results in a solid solution of Ta and Ru up to at least 30% Ru. The alloying has two major effects: the compression of the unit cell with increasing Ru doping modifies the enthalpy of hydrogenation and thereby shifts the pressure window in which the material absorbs hydrogen to higher hydrogen concentrations, and it reduces the amount of hydrogen absorbed by the material. This allows one to tune the pressure/concentration window of the sensor and its sensitivity and makes Ta_1-yRu_y an ideal hysteresis-free tunable hydrogen-sensing material with a sensing range of >7 orders of magnitude in pressure. In a more general perspective, these results demonstrate that one can rationally tune the properties of metal hydride optical hydrogen-sensing layers by appropriate alloying.

Estimating hydrogen absorption energy on different metal hydrides using Gaussian process regression approach

Hydrogen is a promising alternative energy source due to its significantly high energy density. Also, hydrogen can be transformed into electricity in energy systems such as fuel cells. The transition toward hydrogen-consuming applications requires a hydrogen storage method that comes with pack hydrogen with high density. Among diverse methods, absorbing hydrogen on host metal is applicable at room temperature and pressure, which does not provide any safety concerns. In this regard, AB₂ metal hydride with potentially high hydrogen density is selected as an appropriate host. Machine learning techniques have been applied to establish a relationship on the effect of the chemical composition of these hosts on hydrogen storage. For this purpose, a data bank of 314 data point pairs was used. In this assessment, the different A-site and B-site elements were used as the input variables, while the hydrogen absorption energy resulted in the output. A robust Gaussian process regression (GPR) approach with four kernel functions is proposed to predict the hydrogen absorption energy based on the inputs. All the GPR models' performance was quite excellent; notably, GPR with Exponential kernel function showed the highest preciseness with R², MRE, MSE, RMSE, and STD of 0.969, 2.291%, 3.909, 2.501, and 1.878, respectively. Additionally, the sensitivity of analysis indicated that ZR, Ti, and Cr are the most demining elements in this system.

DFT study of hydrogen interaction with transition metal doped graphene for efficient hydrogen storage: effect of d-orbital occupancy and Kubas interaction

Hydrogen adsorption on pristine graphene (PG), graphene with defect (GD), and transition metal (TM) (Ag, Au, Cu, and Fe) doped graphene is systematically investigated for potential hydrogen storage using density functional theory. The stability of the TM atom doped graphene has been analysed by studying the binding energy and the electron density distribution. The TM atom-doped GD shows better binding energy and electron density overlap than PG; therefore, the TM/GD system has been considered and analysed for hydrogen adsorption. The hydrogen adsorption property is studied by examining the adsorption energy, mode of H₂, density of states (DOS), charge density difference, and Löwdin charges before and after adsorption to find a better TM/GD system for hydrogen storage. The Fe/GD system shows higher hydrogen adsorption energy and hydrogen in its stable Kubas mode. Furthermore, two to five H₂ molecule adsorption and desorption is studied. The increase in the number of H₂, which changes the DOS at the Fermi level, suggests that one can predict H₂ concentration by measuring conductivity changes. The present work is focused on studying the interaction between H₂ and TM/GD systems, which will help understand the basic adsorption mechanism for practical hydrogen storage.

Self-supported CoMoO4/NiFe-LDH core-shell nanorods grown on nickel foam for enhanced electrocatalysis of oxygen evolution

Developing high-performance catalysts is an effective strategy for speeding up the oxygen evolution reaction (OER) and increasing production efficiency. Here, a core-shell electrocatalyst consisting of CoMoO₄ nanorods grown in situ on nickel foam substrate covered by nickel-iron layered double hydroxide (NiFe-LDH) via electrodeposition was demonstrated (CoMoO₄/NiFe-LDH@NF). Experimental investigations revealed that self-supporting and binder-free electrodes ensured that the catalysts exposed an abundance of active sites, faster electron transfer, and excellent long-cycle stability. The NiFe-LDH shell with a crystalline-amorphous dual structure served as an accurate active material, lowering the energy barrier and contributing more catalytic sites for water oxidation. Furthermore, the core CoMoO₄ nanorods not only effectively avoided the accumulation of NiFe-LDH to increase the electrochemically active area but also acted as a highway for electrons from the active site to the substrate to promote the OER kinetics. Specifically, CoMoO₄/NiFe-LDH@NF exhibited lower overpotential (180 mV at 10 mA cm^-2) and smaller Tafel slope (34 mV dec^-1) than pure CoMoO₄@NF and NiFe-LDH@NF, revealing its excellent catalytic performance and fast intrinsic reaction kinetics. In addition, CoMoO₄/NiFe-LDH@NF exhibited long-term stability of more than 20 h at 50 mA cm^-2, further demonstrating its potential for practical applications. These findings pointed to a potential option for building innovative OER catalysts.

Amine-Functionalized Natural Halloysite Nanotubes Supported Metallic (Pd, Au, Ag) Nanoparticles and Their Catalytic Performance for Dehydrogenation of Formic Acid

In today’s age of resource scarcity, the low-cost development and utilization of renewable energy, e.g., hydrogen energy, have attracted much attention in the world. In this work, cheap natural halloysite nanotubes (HNTs) were modified with γ-aminopropyltriethoxysilane (APTES), and the functionalized HNTs were used as to support metal (Pd, Au, Ag) catalysts for dehydrogenation of formic acid (DFA). The supports and fabricated catalysts were characterized with ICP, FT-IR, XRD, XPS and TEM. The functional groups facilitate the anchoring of metal particles to the supports, which brings about the high dispersion of metallic particles in catalysts. The catalysts show high activity against DFA and exhibit selectivity of 100% toward H2 at room temperature or less. The interactions between active centers and supports were investigated by evaluation and comparison of the catalytic performances of Pd/NH2-HNTs, PdAg/NH2-HNTs and PdAu/NH2-HNTs for DFA.

Sustainable management of municipal solid waste through waste-to-energy technologies

Increasing municipal solid waste (MSW) generation and environmental concerns have sparked global interest in waste valorization through various waste-to-energy (WtE) to generate renewable energy sources and reduce dependency on fossil-derived fuels and chemicals. These technologies are vital for implementing the envisioned global "bioeconomy" through biorefineries. In light of that, a detailed overview of WtE technologies with their benefits and drawbacks is provided in this paper. Additionally, the biorefinery concept for waste management and sustainable energy generation is discussed. The identification of appropriate WtE technology for energy recovery continues to be a significant challenge. So, in order to effectively apply WtE technologies in the burgeoning bioeconomy, this review provides a comprehensive overview of the existing scenario for sustainable MSW management along with the bottlenecks and perspectives.

A Review of the Impact of Hydrogen Integration in Natural Gas Distribution Networks and Electric Smart Grids

Hydrogen technologies have been rapidly developing in the past few decades, pushed by governments’ road maps for sustainability and supported by a widespread need to decarbonize the global energy sector. Recent scientific progress has led to better performances and higher efficiencies of hydrogen-related technologies, so much so that their future economic viability is now rarely called into question. This article intends to study the integration of hydrogen systems in both gas and electric distribution networks. A preliminary analysis of hydrogen’s physical storage methods is given, considering both the advantages and disadvantages of each one. After examining the preeminent ways of physically storing hydrogen, this paper then contemplates two primary means of using it: integrating it in Power-to-Gas networks and utilizing it in Power-to-Power smart grids. In the former, the primary objective is the total replacement of natural gas with hydrogen through progressive blending procedures, from the transmission pipeline to the domestic burner; in the latter, the set goal is the expansion of the implementation of hydrogen systems—namely storage—in multi-microgrid networks, thus helping to decarbonize the electricity sector and reducing the impact of renewable energy’s intermittence through Demand Side Management strategies. The study concludes that hydrogen is assumed to be an energy vector that is inextricable from the necessary transition to a cleaner, more efficient, and sustainable future.

The Effect of the 3D Nanoarchitecture and Ni-Promotion on the Hydrogen Evolution Reaction in MoS2 /Reduced GO Aerogel Hybrid Microspheres Produced by a Simple One-Pot Electrospraying Procedure

The transition toward renewable energy sources requires low-cost, efficient, and durable electrocatalysts for green H₂ production. Herein, an easy and highly scalable method to prepare MoS₂ nanoparticles embedded in 3D partially reduced (pr) graphene oxide (GO) aerogel microspheres (MoS₂ /prGOAMs) with controlled morphology and composition is described. Given their peculiar center-diverging mesoporous structure, which allows easy access to the active sites and optimal mass transport, and their efficient electron transfer facilitated by the intimate contact between the MoS₂ and the 3D connected highly conductive pr-GO sheets, these materials exhibit a remarkable electrocatalytic activity in the hydrogen evolution reaction (HER). Ni atoms, either as single Ni atoms or NiO aggregates are then introduced in the MoS₂ /prGOAMs hybrids, to facilitate water dissociation, which is the slowest step in alkaline HER, producing a bifunctional catalyst. After optimization, Ni-promoted MoS₂ /prGOAMs obtained at 500 °C reach a remarkable η₁₀ (overpotential at 10 mA cm^-2 ) of 160 mV in 1 m KOH and 174 mV in 0.5 m H₂ SO₄ . Moreover, after chronopotentiometry tests (15 h) at a current density of 10 mA cm^-2 , the η₁₀ value improves to 147 mV in alkaline conditions, indicating an exceptional stability.

Synthesis, Characterization, and Hydrogen Evolution Activity of Metallo-meso-(4-fluoro-2,6-dimethylphenyl)porphyrin Derivatives

Zn(II), Cu(II), and Ni(II) 5,10,15,20-tetrakis(4-fluoro-2,6-dimethylphenyl)porphyrins (TFPs) have been synthesized and characterized. The electronic spectroscopy and cyclic voltammetry of these compounds, along with the free-base macrocycle (2H-TFP), have been determined; 2H-TFP was also structurally characterized by X-ray crystallography. The Cu(II)TFP exhibits catalytic activity for the hydrogen evolution reaction (HER). The analysis of linear sweep voltammograms shows that the HER reaction of Cu(II)TFP with benzoic acid is first-order in proton concentration with an average apparent rate constant for HER catalysis of k app = 5.79 ± 0.47 × 103 M-1 s-1.

Highly Efficient Hierarchical Porous Carbon Supported Pd-Based Catalysts for Additive-Free Dehydrogenation of Formic Acid

Formic acid (FA) is one of the most prospective hydrogen carriers for renewable energy transformation. In this context, the addition of extra-amine is always required for promoting the reactivity of FA, which is still a key challenge. Herein, we report a simple but effective strategy to synthesize Pd nanoparticles, supported on NH2-functionalized, phosphorous-doped glucose-based porous carbon (NH2-P-GC). The introduction of NH2- groups on the support acts as an immobilized amine-additive for FA dehydrogenation, while phosphorus not only serves as an electronic promoter to keep Pd in the electronic deficient state for FA dehydrogenation, but also as an enlarger of the aperture size of the carbon. As a result, the Pd/NH2-P-GC has exceptional catalytic activity, 100% H2 selectivity, CO generation that is undetectable, and good reusability for hydrogen production from FA. In the additive-free dehydrogenation of aqueous FA solution, the initial turnover frequency (TOF) can reach 5126 h−1 at room temperature, which is substantially higher than the best heterogeneous catalyst so far recorded. Overall, the system’s high activity, selectivity, stability, and simplicity in producing CO-free H2/CO2 gas from FA, without the need for any additive, makes it attractive for practical deployment.

Regulation of chlorothalonil degradation by molecular hydrogen

Pesticides can accumulate throughout the food chain to potentially endanger human health. Although molecular hydrogen (H₂) is widely used in industry and medicine, its application in agriculture is just beginning. This study showed that H₂ enhances the degradation of the fungicide chlorothalonil (CHT) in plants, but does not reduce its antifungal efficacy. Pharmacological evidence confirmed the contribution of H₂-stimulated brassinosteroids (BRs) in the above responses. The genetic increased endogenous H₂ with overexpression of hydrogenase 1 gene (CrHYD1) from Chlamydomonas reinhardtii in Arabidopsis not only increased BRs levels, but also eventually intensified the degradation of CHT. Expression of genes encoding some enzymes responsible for detoxification in tomato and Arabidopsis were also stimulated. Contrasting responses were observed after the pharmacological removal of endogenous BR. We further proved that H₂ control of CHT degradation was relatively universal, with at least since its degradation in Chinese cabbage, cucumber, radish, alfalfa, rice, and rapeseed were differentially enhanced by H₂. Collectively, above results clearly indicated that both exogenously and endogenously applied with H₂ could stimulate degradation of CHT partially via BR-dependent detoxification. These results may open a new window for environmental-friendly hydrogen-based agriculture.

PLL-Based Readout Circuit for SiC-MOS Capacitor Hydrogen Sensors in Industrial Environments

For proper operation in real industrial conditions, gas sensors require readout circuits which offer accuracy, noise robustness, energy efficiency and portability. We present an innovative, dedicated readout circuit with a phase locked loop (PLL) architecture for SiC-MOS capacitor sensors. A hydrogen detection system using this circuit is designed, simulated, implemented and tested. The PLL converts the MOS nonlinear small-signal capacitance (affected by hydrogen) into an output voltage proportional to the detected gas concentration. Thus, the MOS sensing element is part of the PLL’s voltage-controlled oscillator. This block effectively provides a small AC signal (around 70 mV at 1 MHz) for the sensor and acquires its response. The correct operation of the proposed readout circuit is validated by simulations and experiments. Hydrogen measurements are performed for concentrations up to 1600 ppm. The PLL output exhibited voltage variations close to those discernable from experimental C-V curves, acquired with a semiconductor characterization system, for all investigated MOS sensor samples.

Surface Roughening Strategy for Highly Efficient Bifunctional Electrocatalyst: Combination of Atomic Layer Deposition and Anion Exchange Reaction

Electrocatalytic water splitting, which is an interface-dominated process, can be significantly accelerated by increasing the number of front-line surface active sites (N_A ) of the electrocatalyst. In this study, a unique method is used for increasing the N_A by converting the smooth ultrathin atomic-layer-deposited nanoshells of the electrocatalysts into nano-roughened active shell layers using a controlled anion-exchange reaction (AER). The coarse thin nanoshells present abundant surface active sites, which are generated owing to the inherent unit-cell volume mismatch induced during the AER. Consequently, the nano-roughened electrodes accelerate the sluggish water reaction kinetics and lower the overpotentials required for the hydrogen and oxygen evolution reactions. In addition, the electronic modulation induced by the nanoshell layer at the core-nanoshell interface amplifies the local electron density, as confirmed using electrochemical analysis data and density functional theory calculations. Because of the integrity of the composite electrodes during water-splitting half-cell reactions, their durability for industrial seawater electrolysis is evaluated. The results indicate that their electrochemical activity does not change significantly after 10 days of continuous overall water splitting.

On the growth regimes of hydrogen bubbles at microelectrodes

Beside classical growth (regime I), depending on potential and concentration, new growth regimes of hydrogen bubbles were found. These differ with respect to the existence of a carpet of microbubbles underneath and of current oscillations.

Effect of feed impurities on catalytic performance of CuFe2O4/β-SiC for SO3 decomposition in the sulfur–iodine cycle

CuFe2O4/β-SiC exhibits high activity and stability in the presence of feed impurities in SO3 decomposition reaction. A mathematical model is developed and validated to predict SO3 conversion at different feed compositions and temperatures.

Efficient solventless dehydrogenation of formic acid by a CNC-based rhodium catalyst

A CNC based rhodium complex is an efficient catalyst for formic acid dehydrogenation under solventless conditions.

Resistivity Testing of Palladium Dilution Limits in CoPd Alloys for Hydrogen Storage

Palladium satisfies most of the requirements for an effective hydrogen storage material with two major drawbacks: it has a relatively low gravimetric hydrogen density and is prohibitively expensive for large scale applications. Pd-based alloys should be considered as possible alternatives to a pure Pd. The question is how much one can dilute the Pd concentration in a variety of candidate materials while preserving the hydrogen absorption capability. We demonstrate that the resistivity measurements of thin film alloy samples can be used for a qualitative high-throughput screening and study of the hydrogen absorbing properties over the entire range of palladium concentrations. Contrary to palladium-rich alloys where additional hydrogen scattering indicates a degree of hydrogen content, the diluted alloy films respond by a decrease in resistance due to their thickness expansion. Evidence of significant hydrogen absorption was found in thin CoPd films diluted to just 20% of Pd.

Hydrogenation Kinetics of Metal Hydride Catalytic Layers

Catalyzing capping layers on metal hydrides are employed to enhance the hydrogenation kinetics of metal hydride-based systems such as hydrogen sensors. Here, we use a novel experimental method to study the hydrogenation kinetics of catalyzing capping layers composed of several alloys of Pd and Au as well as Pt, Ni, and Ru, all with and without an additional PTFE polymer protection layer and under the same set of experimental conditions. In particular, we employ a thin Ta film as an optical indicator to study the kinetics of the catalytic layers deposited on top of it and which allows one to determine the absolute hydrogenation rates. Our results demonstrate that doping Pd with Au results in significantly faster hydrogenation kinetics, with response times up to five times shorter than Pd through enhanced diffusion and a reduction in the activation energy. On the other hand, the kinetics of non-Pd-based materials turn out to be significantly slower and mainly limited by the diffusion through the capping layer itself. Surprisingly, the additional PTFE layer was only found to improve the kinetics of Pd-based capping materials and has no significant effect on the kinetics of Pt, Ni, and Ru. Taken together, the experimental results aid in rationally choosing a suitable capping material for the application of metal hydrides and other materials in a hydrogen economy. In addition, the used method can be applied to simultaneously study the hydrogenation kinetics in thin-film materials for a wide set of experimental conditions.

Destabilization of Boron-Based Compounds for Hydrogen Storage in the Solid-State: Recent Advances

Boron-based materials have been widely studied for hydrogen storage applications. Examples of these compounds are borohydrides and boranes. However, all of these present some disadvantages that have hindered their potential application as hydrogen storage materials in the solid-state. Thus, different strategies have been developed to improve the dehydrogenation properties of these materials. The purpose of this review is to provide an overview of recent advances (for the period 2015–2021) in the destabilization strategies that have been considered for selected boron-based compounds. With this aim, we selected seven of the most investigated boron-based compounds for hydrogen storage applications: lithium borohydride, sodium borohydride, magnesium borohydride, calcium borohydride, ammonia borane, hydrazine borane and hydrazine bisborane. The destabilization strategies include the use of additives, the chemical modification and the nanosizing of these compounds. These approaches were analyzed for each one of the selected boron-based compounds and these are discussed in the present review.

Thermocatalytic Hydrogen Production Through Decomposition of Methane-A Review

Consumption of fossil fuels, especially in transport and energy-dependent sectors, has led to large greenhouse gas production. Hydrogen is an exciting energy source that can serve our energy purposes and decrease toxic waste production. Decomposition of methane yields hydrogen devoid of COx components, thereby aiding as an eco-friendly approach towards large-scale hydrogen production. This review article is focused on hydrogen production through thermocatalytic methane decomposition (TMD) for hydrogen production. The thermodynamics of this approach has been highlighted. Various methods of hydrogen production from fossil fuels and renewable resources were discussed. Methods including steam methane reforming, partial oxidation of methane, auto thermal reforming, direct biomass gasification, thermal water splitting, methane pyrolysis, aqueous reforming, and coal gasification have been reported in this article. A detailed overview of the different types of catalysts available, the reasons behind their deactivation, and their possible regeneration methods were discussed. Finally, we presented the challenges and future perspectives for hydrogen production via TMD. This review concluded that among all catalysts, nickel, ruthenium and platinum-based catalysts show the highest activity and catalytic efficiency and gave carbon-free hydrogen products during the TMD process. However, their rapid deactivation at high temperatures still needs the attention of the scientific community.

Effects of feedstock and pyrolysis temperature of biochar on promoting hydrogen production of ethanol-type fermentation

Biochar has been shown to benefit fermentative hydrogen production. However, the influencing factors and key characteristics of its promoting function remained to be elucidated. This study investigated the effects of two crucial factors, feedstock and pyrolysis temperature, on the hydrogen production-promoting function of biochar in ethanol-type fermentation. The physicochemical characteristics and promoting effects of biochars prepared with five biomass wastes (coffee ground, corn stalk, Ginkgo biloba leaf, mealworm frass, and sugarcane bagasse) were determined. Sugarcane bagasse-derived biochar (SBBC) showed the best hydrogen production-promoting effect in ethanol-type fermentation. The physicochemical properties of biochar, such as pH, element composition and surface features, were significantly affected by pyrolysis temperature, but the promoting effects were not significantly changed. The hydrogen production-promoting effect of biochar in ethanol-type fermentation was mainly affected by feedstock instead of pyrolysis temperature. A potential promoting mechanism was proposed that biochar prepared at low temperature boosted the hydrogen production with redox activity, while that at high temperature achieved the promotion via cell growth enhancement. This study revealed the key promoting factor of biochar in ethanol-type fermentative hydrogen production, and provided novel insights for the promoting mechanism of biochar.

Formation of Hydrogen Peroxide from O-(H2O)n Clusters

Hydrogen peroxide (H₂O₂) has recently received much attention as a safe and clean energy carrier for hydrogen molecules. In this study, based on direct ab initio molecular dynamics (AIMD) calculations, we demonstrated that H₂O₂ is directly formed via the photoelectron detachment of O^-(H₂O)_n (n = 1-6) (water clusters of an oxygen radical anion). Three electronic states of oxygen atoms were examined in the calculations: O(X)(H₂O)_n (X = ³P, ¹D, and ¹S states). After the photoelectron detachment of O^-(H₂O)_n (n = 1) to the ¹S state, a complex comprising O(¹S) and H₂O, O(¹S)-OH₂, was formed. A hydrogen atom of H₂O immediately transferred to O(¹S) during an intracluster reaction to form H₂O₂ as the final product. Simulations were run to obtain a total of 33 trajectories for n = 1 that all led to the formation of H₂O₂. The average reaction time of H₂O₂ formation was calculated to be 57.7 fs in the case of n = 1, indicating that the reaction was completed within 100 fs of electron detachment. All the reaction systems O(¹S)(H₂O)_n (n = 1-6) indicated the formation of H₂O₂ by the same mechanism. The reaction times for n = 2-6 were calculated to range between 80 and 180 fs, indicating that the reaction for n = 1 is faster than that of the larger clusters, that is, the larger the cluster size, the slower the reaction is. The reaction dynamics of the triplet O(³P) and singlet O(¹D) potential energy surfaces were calculated for comparison. All calculations yielded the dissociation product O(X)(H₂O)_n → O(X) + (H₂O)_n (X = ³P and ¹D), indicating that the O(¹S) state contributes to the formation of H₂O₂. The reaction mechanism was discussed based on the theoretical results.

Bifunctional and Self-Supported NiFeP-Layer-Coated NiP Rods for Electrochemical Water Splitting in Alkaline Solution

Designing efficient and robust nonprecious metal-based electrocatalysts for overall water electrolysis, which is mainly limited by the oxygen evolution reaction (OER), for hydrogen production remains a major challenge for the hydrogen economy. In this work, a bimetallic NiFeP catalyst is coated on nickel phosphide rods grown on nickel foam (NiFeP@NiP@NF). This self-supported and interfacially connected electrode structure is favorable for mass transfer and reducing electrical resistance during electrocatalysis. The preparation of NiFeP@NiP@NF is optimized in terms of (i) the coprecipitation time of the NiFe Prussian blue analogue layer that serves as phosphides precursor and (ii) the phosphidation temperature. The optimized sample exhibits excellent OER performance delivering current densities of 10 and 100 mA cm^-2 at low overpotentials of 227 and 252 mV in 1.0 M KOH, respectively, and maintaining 10 mA cm^-2 for more than 120 h without obvious degradation. Moreover, it can also be operated as a hydrogen evolution electrocatalyst, requiring an overpotential of 105 mV at 10 mA cm^-2 in the same medium. Thus, the as-prepared material was tentatively utilized as a bifunctional electrocatalyst in a symmetric electrolyzer, requiring a voltage bias of 1.57 V to afford 10 mA cm^-2 in 1.0 M KOH, while exhibiting outstanding stability.

Molecular Design of a Reversible Hydrogen Storage Device Composed of the Graphene Nanoflake-Magnesium-H2 System

Carbon materials such as graphene nanoflakes (GRs), carbon nanotubes, and fullerene can be widely used for hydrogen storage. In general, metal doping of these materials leads to an increase in their H2 storage density. In the present study, the binding energies of H2 to Mg species on GRs, GR-Mg m+ (m = 0-2), were calculated using density functional theory calculations. Mg has a wide range of atomic charges. In the case of GR-Mg (m = 0, Mg atom), the binding energy of one H2 molecule is close to 0, whereas those for m = 1 (Mg+) and 2 (Mg2+) are 0.23 and 13.2 kcal/mol (n = 1), respectively. These features suggest that GR-Mg2+ has a strong binding affinity toward H2, whereas GR-Mg+ has a weak binding energy. In addition, it was found that the first coordination shell is saturated by four H2 molecules, GR-Mg2+-(H2) n (n = 4). Next, direct ab initio molecular dynamics calculations were carried out for the electron-capture process of GR-Mg2+-(H2) n and a hole-capture process of GR-Mg+-(H2) n (n = 4). After electron capture, the H2 molecules left and dissociated from GR-Mg+: GR-Mg2+-(H2) n + e- → GR-Mg+ + (H2) n (H2 is released into the gas phase). In contrast, the H2 molecules were bound again to GR-Mg2+ after the hole capture of GR-Mg+: GR-Mg+ + (H2) n (gas phase) + hole → GR-Mg2+-(H2) n . On the basis of these calculations, a model device with reversible H2 adsorption-desorption properties was designed. These results strongly suggest that the GR-Mg system is capable of H2 adsorption-desorption reversible storage.

TiO2-Graphene Quantum Dots Nanocomposites for Photocatalysis in Energy and Biomedical Applications

The focus of current research in material science has shifted from “less efficient” single-component nanomaterials to the superior-performance, next-generation, multifunctional nanocomposites. TiO2 is a widely used benchmark photocatalyst with unique physicochemical properties. However, the large bandgap and massive recombination of photogenerated charge carriers limit its overall photocatalytic efficiency. When TiO2 nanoparticles are modified with graphene quantum dots (GQDs), some significant improvements can be achieved in terms of (i) broadening the light absorption wavelengths, (ii) design of active reaction sites, and (iii) control of the electron-hole (e−-h+) recombination. Accordingly, TiO2-GQDs nanocomposites exhibit promising multifunctionalities in a wide range of fields including, but not limited to, energy, biomedical aids, electronics, and flexible wearable sensors. This review presents some important aspects of TiO2-GQDs nanocomposites as photocatalysts in energy and biomedical applications. These include: (1) structural formulations and synthesis methods of TiO2-GQDs nanocomposites; (2) discourse about the mechanism behind the overall higher photoactivities of these nanocomposites; (3) various characterization techniques which can be used to judge the photocatalytic performance of these nanocomposites, and (4) the application of these nanocomposites in biomedical and energy conversion devices. Although some objectives have been achieved, new challenges still exist and hinder the widespread application of these nanocomposites. These challenges are briefly discussed in the Future Scope section of this review.

Highly efficient additive-free dehydrogenation of neat formic acid

Formic acid (FA) is a promising hydrogen carrier which can play an instrumental role in the overall implementation of a hydrogen economy. In this regard, it is important to generate H₂ gas from neat FA without any solvent/additive, for which existing systems are scarce. Here we report the remarkable catalytic activity of a ruthenium 9H-acridine pincer complex for this process. The catalyst is unusually stable and robust in FA even at high temperatures and can catalyse neat FA dehydrogenation for over a month, with a total turnover number of 1,701,150, while also generating high H₂/CO₂ gas pressures (tested up to 100 bars). Mechanistic investigations and DFT studies are conducted to fully understand the molecular mechanism to the process. Overall, the high activity, stability, selectivity, simplicity and versatility of the system to generate a CO-free H₂/CO₂ gas stream and high pressure from neat FA makes it promising for large-scale implementation.

Is the H2 economy realizable in the foreseeable future? Part III: H2 usage technologies, applications, and challenges and opportunities

Energy enthusiasts in developed countries explore sustainable and efficient pathways for accomplishing zero carbon footprint through the H₂ economy. The major objective of the H₂ economy review series is to bring out the status, major issues, and opportunities associated with the key components such as H₂ production, storage, transportation, distribution, and applications in various energy sectors. Specifically, Part I discussed H₂ production methods including the futuristic ones such as photoelectrochemical for small, medium, and large-scale applications, while Part II dealt with the challenges and developments in H₂ storage, transportation, and distribution with national and international initiatives. Part III of the H₂ economy review discusses the developments and challenges in the areas of H₂ application in chemical/metallurgical industries, combustion, and fuel cells. Currently, the majority of H₂ is being utilized by a few chemical industries with >60% in the oil refineries sector, by producing grey H₂ by steam methane reforming on a large scale. In addition, the review also presents the challenges in various technologies for establishing greener and sustainable H₂ society.

Prospects of Fuel Cell Combined Heat and Power Systems

Combined heat and power (CHP) in a single and integrated device is concurrent or synchronized production of many sources of usable power, typically electric, as well as thermal. Integrating combined heat and power systems in today’s energy market will address energy scarcity, global warming, as well as energy-saving problems. This review highlights the system design for fuel cell CHP technologies. Key among the components discussed was the type of fuel cell stack capable of generating the maximum performance of the entire system. The type of fuel processor used was also noted to influence the systemic performance coupled with its longevity. Other components equally discussed was the power electronics. The thermal and water management was also noted to have an effect on the overall efficiency of the system. Carbon dioxide emission reduction, reduction of electricity cost and grid independence, were some notable advantages associated with fueling cell combined heat and power systems. Despite these merits, the high initial capital cost is a key factor impeding its commercialization. It is, therefore, imperative that future research activities are geared towards the development of novel, and cheap, materials for the development of the fuel cell, which will transcend into a total reduction of the entire system. Similarly, robust, systemic designs should equally be an active research direction. Other types of fuel aside, hydrogen should equally be explored. Proper risk assessment strategies and documentation will similarly expand and accelerate the commercialization of this novel technology. Finally, public sensitization of the technology will also make its acceptance and possible competition with existing forms of energy generation feasible. The work, in summary, showed that proton exchange membrane fuel cell (PEM fuel cell) operated at a lower temperature-oriented cogeneration has good efficiency, and is very reliable. The critical issue pertaining to these systems has to do with the complication associated with water treatment. This implies that the balance of the plant would be significantly affected; likewise, the purity of the gas is crucial in the performance of the system. An alternative to these systems is the PEM fuel cell systems operated at higher temperatures.

Laser Induced Anchoring of Nickel Oxide Nanoparticles on Polymeric Graphitic Carbon Nitride Sheets Using Pulsed Laser Ablation for Efficient Water Splitting under Visible Light

A visible-light-active nickel oxide-graphitic carbon nitride (NiO@g-CN) hetero-structured nanocomposite was synthesized for the first time by pulsed laser ablation in liquid and used as a photoanode material in photoelectrochemical water-splitting reaction with a solar simulator. It was found that the photoelectrochemical performance of PLAL synthesized NiO@g-CN nanocomposite as photoanode, compared to g-CN as photoanode showed fourfold enhancements in photocurrent density under visible light. FT-IR, XRD, FE-SEM, and EDX consistently showed the proper anchoring of nano-sized NiO on g-CN. UV-DRS and the band gap estimation showed the narrowing down of the band gap energy and consequent enhancement in the visible-light absorption, whereas photoluminescence spectroscopy confirmed the reduction of the recombination of photo-excited electron hole pairs as a result of the anchoring of NiO on g-CN. The photoelectrochemical performance of g-CN and the NiO@g-CN nanocomposite photoanodes was compared by linear sweep voltammetry (LSV), Chronoamperometry (I-t), and Electrochemical Impedance Spectroscopy (EIS). All of these results of the characterization studies account for the observed fourfold enhancement of photocurrent density of NiO@g-CN nanocomposite as photoanode in the photoelectrochemical reaction.

Synthesis of Large-Scale Bio-Hydrogen Network Using Waste Gas from Landfill and Anaerobic Digestion: A P-Graph Approach

Due to the expanding concern on cleaner production and sustainable development aspects, a technology shift is needed for the hydrogen production, which is commonly derived from natural gas. This work aims to synthesise a large-scale bio-hydrogen network in which its feedstock, i.e., bio-methane, is originated from landfill gas and palm oil mill effluent (POME). Landfill gas goes through a biogas upgrader where high-purity bio-methane is produced, while POME is converted to bio-methane using anaerobic digestor (AD). The generated bio-methane is then distributed to the corresponding hydrogen sink (e.g., oil refinery) through pipelines, and subsequently converted into hydrogen via steam methane reforming (SMR) process. In this work, P-graph framework is used to determine a supply network with minimum cost, while ensuring the hydrogen demands are satisfied. Two case studies in the West and East Coasts of Peninsular Malaysia are used to illustrate the feasibility of the proposed model. In Case Study 1, four scenarios on the West Coast have been considered, showing total cost saving ranging between 25.9% and 49.5%. This showed that aside from the positive environmental impact, the incorporation of bio-hydrogen supply can also be economically feasible. Such benefits can also be seen in Case Study 2, where the uptake of biogas from landfill and POME sources on the East Coast can lead to a 31% reduction on total network cost. In addition, the effect of bio-hydrogen supply network on carbon footprint reduction was analysed in this work.

Integration of Hydrogen into Multi-Energy Systems Optimisation

Hydrogen presents an attractive option to decarbonise the present energy system. Hydrogen can extend the usage of the existing gas infrastructure with low-cost energy storability and flexibility. Excess electricity generated by renewables can be converted into hydrogen. In this paper, a novel multi-energy systems optimisation model was proposed to maximise investment and operating synergy in the electricity, heating, and transport sectors, considering the integration of a hydrogen system to minimise the overall costs. The model considers two hydrogen production processes: (i) gas-to-gas (G2G) with carbon capture and storage (CCS), and (ii) power-to-gas (P2G). The proposed model was applied in a future Great Britain (GB) system. Through a comparison with the system without hydrogen, the results showed that the G2G process could reduce £3.9 bn/year, and that the P2G process could bring £2.1 bn/year in cost-savings under a 30 Mt carbon target. The results also demonstrate the system implications of the two hydrogen production processes on the investment and operation of other energy sectors. The G2G process can reduce the total power generation capacity from 71 GW to 53 GW, and the P2G process can promote the integration of wind power from 83 GW to 130 GW under a 30 Mt carbon target. The results also demonstrate the changes in the heating strategies driven by the different hydrogen production processes.