Characterization of slow pyrolysis biochars: effects of feedstocks and pyrolysis temperature on biochar properties

Influence of agro-wastes derived biochar and their composite on reducing the mobility of toxic heavy metals and their bioavailability in industrial contaminated soils

The agro-waste derived valuable products are prime interest for effective management of toxic heavy metals (THMs). The present study investigated the efficacy of biochars (BCs) on immobilization of THMs (Cr, Zn, Pb, Cu, Ni and Cd), bioaccumulation and health risk. Agro-wastes derived BCs including wheat straw biochar (WSB), orange peel biochar (OPB), rice husk biochar (RHB) and their composite biochar (CB) were applied in industrial contaminated soil (ICS) at 1% and 3% amendments rates. All the BCs significantly decreased the bioavailable THMs and significantly (p < 0.001) reduced bioaccumulation at 3% application with highest efficiency for CB followed by OPB, WSB and RHB as compared to control treatment. The bioaccumulation factor (BAF), concentration index (CI) and ecological risk were decreased with all BCs. The hazard quotient (HQ) and hazard index (HI) of all THMs were <1, except Cd, while carcer risk (CR) and total cancer risk index (TCRI) were decreased through all BCs. The overall results depicted that CB at 3% application rate showed higher efficacy to reduce significantly (p < 0.001) the THMs uptake and reduced health risk. Hence, the present study suggests that the composite of BCs prepared from agro-wastes is eco-friendly amendment to reduce THMs in ICS and minimize its subsequent uptake in vegetables.

Phytotoxicity and hormesis in common mobile organic compounds in leachates of wood-derived biochars

Although addition of pyrolyzed organic materials (biochars) to soil generally results in increased growth and physiological performance of plants, neutral and negative responses have also commonly been detected. Toxicity of organic compounds generated during pyrolysis, sorbed by biochars, and then released into the soil solution, has been implicated as a possible mechanism for such negative effects. Conversely, water-soluble biochar constituents have also been suggested to have "hormetic" effects (positive effects on plants at low concentrations); however, no specific compounds responsible have been identified. We investigated the relative phytotoxicity-and possible hormetic effects-of 14 organic compounds common in aqueous extracts of freshly produced lignocellulosic biochars, using seed germination bioassays. Of the compounds examined, volatile fatty acids (VFAs: acetic, propionic, butyric, valeric, caproic, and 2-ethylbutyric acids) and phenol, showed acute phytotoxicity, with germination-based ED50 values of 1-30 mmol L-1, and 2-ethylbutyric acid showed ED50 values of 0.1-1.0 mmol L-1. Other compounds (benzene, benzoic acid, butanone, methyl salicylate, toluene, and 2,4-di-tert-butylphenol) showed toxic effects only at high concentrations close to solubility limits. Although phytotoxic at high concentrations, valeric and caproic acid also showed detectable hormetic effects on seedlings, increasing radicle extension by 5-15% at concentrations of ~ 0.01-0.1 mmol L-1. These data support the hypothesis that VFAs are the main agents responsible for phytotoxic effects of lignocellulosic biochar leachates, but that certain VFAs also have hormetic effects at low concentrations and may contribute to positive effects of biochar leachates on early plant development in some cases.

Graphical Abstract

Supplementary Information

The online version contains supplementary material available at 10.1007/s42773-024-00339-w.

Fuel Characteristics and Phytotoxicity Assay of Biochar Derived from Rose Pruning Waste

The aim of this study was the characterization and evaluation of applicability as a soil amendment of biochar derived from rose pruning waste at different pyrolysis temperatures (200-500 °C) and process durations (20-60 min). The biochar properties were compared to the raw material. The biochars produced at 300 °C for 40 and 60 min demonstrated the best fuel properties. These variants showed high energy gain rates (77.6 ± 1.5% and 74.8 ± 1.5%, respectively), energy densification ratios (1.35 ± 0.00 and 1.37 ± 0.00, respectively), high heating values (24,720 ± 267 J × g-1 and 25,113 ± 731 J × g-1, respectively), and relative low ash contents (5.9 ± 0.5% and 7.1 ± 0.3%, respectively). Regarding fertilizer properties, such as pH value, ash content, heavy metal content, and pollutant elution, the biochars showed better qualities than the raw material. All tested biochar did not exceed the permissible values for heavy metals, including Cr, Cd, Ni, and Pb. The most optimal properties for soil amendments were noted for biochar variants of 400 °C for 40 min, 450 °C for 20 min, and 500 °C for 20 min. Generally, biochars produced at temperatures ≥400 °C did not inhibit root elongation, except for the material produced at 450 °C for 60 min (4.08 ± 23.34%). Biochars obtained at ≥300 °C showed a positive impact on seed germination (86.67 ± 18.48-100 ± 24.14%).

Biochar obtained from eucalyptus, rice hull, and native bamboo as an alternative to decrease mobility of hexazinone, metribuzin, and quinclorac in a tropical soil

Mobile herbicides have a high potential for groundwater contamination. An alternative to decrease the mobility of herbicides is to apply materials with high sorbent capacity to the soil, such as biochars. The objective of this research was to evaluate the effect of eucalyptus, rice hull, and native bamboo biochar amendments on sorption and desorption of hexazinone, metribuzin, and quinclorac in a tropical soil. The sorption-desorption was evaluated using the batch equilibrium method at five concentrations of hexazinone, metribuzin, and quinclorac. Soil was amended with eucalyptus, rice hull, and native bamboo biochar at a rate of 0 (control-unamended) and 1% (w w-1), corresponding to 0 and 12 t ha-1, respectively. The amount of sorbed herbicides in the unamended soil followed the decreasing order: quinclorac (65.9%) > metribuzin (21.4%) > hexazinone (16.0%). Native bamboo biochar provided the highest sorption compared to rice hull and eucalyptus biochar-amended soils for the three herbicides. The amount of desorbed herbicides in the unamended soil followed the decreasing order: metribuzin (18.35%) > hexazinone (15.9%) > quinclorac (15.1%). Addition of native bamboo biochar provided the lowest desorption among the biochar amendments for the three herbicides. In conclusion, the biochars differently affect the sorption and desorption of hexazinone, metribuzin, and quinclorac mobile herbicides in a tropical soil. The addition of eucalyptus, rice hull, and native bamboo biochars is a good alternative to increase the sorption of hexazinone, metribuzin, and quinclorac, thus, reducing mobility and availability of these herbicides to nontarget organisms in soil.

Divergent responses of phosphorus solubilizing bacteria with P-laden biochar for enhancing nutrient recovery, growth, and yield of canola (Brassica napus L.)

The growing global population has led to a heightened need for food production, and this rise in agricultural activity is closely tied to the application of phosphorus-based fertilizers, which contributes to the depletion of rock phosphate (RP) reserves. Considering the limited P reserves, different approaches were conducted previously for P removal from waste streams, while the adsorption of ions is a novel strategy with more applicability. In this study, a comprehensive method was employed to recover phosphorus from wastewater by utilizing biochar engineered with minerals such as calcium, magnesium, and iron. Elemental analysis of the wastewater following a batch experiment indicated the efficiency of the engineered biochar as an adsorbent. Subsequently, the phosphorus-enriched biochar, hereinafter (PL-BCsb), obtained from the wastewater, underwent further analysis through FTIR, XRD, and nutritional assessments. The results revealed that the PL-BCsb contained four times higher (1.82%) P contents which further reused as a fertilizer supplementation for Brassica napus L growth. PL-BCsb showed citric acid (34.03%), Olsen solution (10.99%), and water soluble (1.74%) P desorption. Additionally, phosphorous solubilizing bacteria (PSB) were incorporated with PL-BCsb along two P fertilizer levels P45 (45 kg ha-1) and P90 (90 kg ha-1) for evaluation of phosphorus reuse efficiency. Integrated application of PL-BCsb with half of the suggested amount of P45 (45 kg ha-1) and PSB increased growth, production, physiological, biochemical, and nutritional qualities of canola by almost two folds when compared to control. Similarly, it also improved soil microbial biomass carbon up to four times, alkaline and acid phosphatases activities both by one and half times respectively as compared to control P (0). Furthermore, this investigation demonstrated that waste-to-fertilizer technology enhanced the phosphorus fertilizer use efficiency by 55-60% while reducing phosphorus losses into water streams by 90%. These results have significant implications for reducing eutrophication, making it a promising approach for mitigating environmental pollution and addressing climate change.

Formation mechanisms and degradation methods of polycyclic aromatic hydrocarbons in biochar: A review

Biochar has been widely used in soil amendment and environmental remediation. Polycyclic aromatic hydrocarbons (PAHs) could be produced in preparation of biochar, which may pose potential risks to the environment and human health. At present, most studies focus on the ecotoxicity potential of biochar, while there are few systematic reviews on the formation mechanisms and mitigation strategies of PAHs in biochar. Therefore, a systematical understanding of the distribution, formation mechanisms, risk assessment, and degradation approaches of PAHs in biochar is highly needed. In this paper, the distribution and content of the total and bioavailable PAHs in biochar are reviewed. Then the formation mechanisms, influencing factors, and potential risk assessment of PAHs in biochar are systematically explored. After that, the effective strategies to alleviate PAHs in biochar are summarized. Finally, suggestions and perspectives for future studies are proposed. This review provides a guide for reducing the formation of biochar-associated PAHs and their toxicity, which is beneficial for the development and large-scale safe use of environmentally friendly biochar.

Definitive Review of Nanobiochar

Nanobiochar is an advanced nanosized biochar with enhanced properties and wide applicability for a variety of modern-day applications. Nanobiochar can be developed easily from bulk biochar through top-down approaches including ball-milling, centrifugation, sonication, and hydrothermal synthesis. Nanobiochar can also be modified or engineered to obtain "engineered nanobiochar" or biochar nanocomposites with enhanced properties and applications. Nanobiochar provides many fold enhancements in surface area (0.4-97-times), pore size (0.1-5.3-times), total pore volume (0.5-48.5-times), and surface functionalities over bulk biochars. These enhancements have given increased contaminant sorption in both aqueous and soil media. Further, nanobiochar has also shown catalytic properties and applications in sensors, additive/fillers, targeted drug delivery, enzyme immobilization, polymer production, etc. The advantages and disadvantages of nanobiochar over bulk biochar are summarized herein, in detail. The processes and mechanisms involved in nanobiochar synthesis and contaminants sorption over nanobiochar are summarized. Finally, future directions and recommendations are suggested.

Using the Conditional Process Analysis Model to Characterize the Evolution of Carbon Structure in Taxodium ascendens Biochar with Varied Pyrolysis Temperature and Holding Time

Temperature determines biochar structure during pyrolysis. However, differences in holding time and feedstock types may affect this relationship. The conditional process analysis model was used in this paper to investigate the potential to affect this mechanism. The branch and leaf parts of Taxodium ascendens were separately pyrolyzed at 350, 450, 650, and 750 °C, and kept for 0.5, 1, and 2 h at each target temperature. We measured the fixed carbon and ash contents and the elemental composition (C, H, O and N) of the raw materials and their char samples. After plotting a Van Krevelen (VK) diagram to determine the aromatization of chars, the changes in the functional groups were analyzed using Fourier transform infrared (FTIR), Raman, and X-ray photoelectron spectroscopy (XPS). The results revealed that pyrolysis at temperatures between 450 and 750 °C accounted for the aromatization of biochar because the atomic H/C ratio of branch-based chars (BC) decreased from 0.53-0.59 to 0.15-0.18, and the ratio of leaf-based chars (LC) decreased from 0.56-0.68 to 0.20-0.22; the atomic O/C ratio of BC decreased from 0.22-0.27 to 0.08-0.11, while that of LC decreased from 0.26-0.28 to 0.18-0.21. Moreover, the average contents of N (1.89%) and ash (13%) in LC were evidently greater than that in BC (N:0.62%; Ash: 4%). Therefore, BC was superior to LC in terms of the stability of biochar. In addition, the increasing ID/IG and ID/I(DR+GL) ratios in BC and LC indicated an increasing amount of the amorphous aromatic carbon structure with medium-sized (2~6 rings) fused benzene rings. According to the CPA analysis, an extension of the holding time significantly enhanced the increase in aromatic structures of LC with temperature. But this extension slightly reduced the growth in aromatic structures of BC. All indicate that holding time and feedstock types (branch or leaf feedstock) could significantly affect the variation in biochar aromatic structure with respect to temperature.

Comparison of Adsorption Performance of Biochar Derived from Urban Biowaste Materials for Removal of Heavy Metals

This study investigated the adsorption performance of biochar produced from different types of urban biowaste material viz., sugarcane bagasse (SB), brinjal stem (BS), and citrus peel (CP) for removal of heavy metal ions (Pb, Cu, Cr, and Cd) from aqueous solution. The effects of biowaste material, dosage of biochar, solution pH, and initial concentration of heavy metal ions and isotherm models were performed to understand the possible adsorption mechanisms. The results showed that the biochar derived from BS and SB removes Cu (99.94%), Cr (99.57%), and Cd (99.77%) whereas biochar derived from CP removes Pb (99.59%) and Cu (99.90%) more efficiently from the aqueous solution. Biochar derived from BS showed maximum adsorption capacity for Cu (246.31 mg g-1), Pb (183.15 mg g-1), and Cr (71.89 mg g-1) while the biochar derived from CP showed highest for Cd (15.46 mg g-1). Moreover, biochar derived from BS and SB has more polar functional groups and less hydrophobicity than the biochar derived from CP. This study reveals that solution pH and biochar doses play a major role in removal of heavy metal ions from aqueous solution. The results of Langmuir model fitted well for Pb and Cu while the Freundlich model for Cr and Cd. Our study concludes that the biochar derived from different biowaste materials adsorbs heavy metal ions majorly through surface complexation and precipitation processes. The results of this study will be very useful in selecting the effective urban biowaste material for making biochar for heavy metal removal from the aqueous environment.

Distribution of PAHs, PCBs, and PCDD/Fs in products from full-scale relevant pyrolysis of diverse contaminated organic waste

Biomass pyrolysis is the anoxic thermal conversion of biomass into a carbon rich, porous solid, often called biochar. This could be a better waste management alternative for contaminated organic wastes than incineration, due to the useful properties of biochar and potential for carbon sequestration. There are, however, concerns about the potential formation/destruction of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs). Six organic wastes, including digested sewage sludges, wood wastes, and food waste reject, were pyrolyzed (500-800°C) in a full-scale relevant unit (1-5 kg biochar hr-1). Removal efficiencies for PCBs and PCDD/Fs were > 99% in the produced biochars. Biochar PAH-content (2.7-118 mgkg-1) was not significantly correlated to feedstock or temperature. PAHs (2563-8285 mgkg-1), PCBs (22-113 µgkg-1), and PCDD/Fs (1.8-50 ngTEQ kg-1) accumulated in the pyrolysis condensate, making this a hazardous waste best handled as a fuel for high temperature combustion. Emission concentrations for PAHs (0.22-421 µgNm-3) and PCDD/Fs (≤2.7 pgTEQ Nm-3) were mainly associated with particles and were below the European Union's waste incineration thresholds. Emission factors ranged from 0.0002 to 78 mg tonne-1 biochar for PAHs and 0.002-0.45 µgTEQ tonne-1 biochar for PCDD/Fs. PCDD/F-formation was negligible during high temperature (≥500 °C) biomass pyrolysis (69-90% net loss).

Utilization of palm residues for biochar production using continuous flow pyrolysis unit

Biochar is a carbonaceous solid substance produced by heating biomass without using air. This research aimed to create and evaluate local carbonization pyrolysis using a screw conveyor and filtration equipment. Date palm frond (DPF) biochar was studied and tested at pyrolysis temperatures of 320, 390, and 460 °C, as well as feeding rates of 60, 90, and 120 kg/h. The physicochemical parameters of DPF biochar were evaluated using SEM and FTIR. When the pyrolysis temperature was raised from 320 to 450 °C, and the feed rates were reduced from 120 to 60 kg/h, the biochar yield of DPF and volatiles fell. At 460 °C and 60 kg/h, the maximum ash and fixed carbon content were 11.73 and 77.61 %, respectively. As the feed rate decreased and the temperature increased, the H and O values (1.96 and 2.62 %, respectively) of DPF biochar decreased considerably; the C and N values (83.60 and 0.24 %, respectively) trended in opposite directions. The BET surface area and pore volume increased as a result of the micropore surface area and volume at higher temperatures and lower feeding rates, but water holding capacity increased from 6.04 gwater/10 g at 320 °C to 6.78 gwater/10 g at 390 °C (60 kg/h). The results showed that the heating temperature increased and the feeding rate decreased; phosphorus) P(and magnesium (Mg) increased significantly, whereas the levels of potassium (K) and calcium (Ca) showed a non-significant increase. Furthermore, as the pyrolysis temperature increased, pH and EC increased from 7.90 to 10.96 and 2.91 to 4.25 dSm-1, respectively, while CEC declined; however, there were no significant changes in CEC. DPF biochar demonstrated enhanced macro porosity and surface area at 460 °C and 60 kg/h, making it acceptable for agricultural use as a soil supplement.

Substituting Solid Fossil Fuels with Torrefied Timber Products

As a push towards alternative and renewable resources for heat and power generation, biomass and thermally treated fuels from biomass may be viable options in the upcoming economic reality. This study the verified mass and energy balance of spruce woody biomass after low temperature pyrolysis between 250 and 550 °C. The results showed that low-temperature pyrolysis can yield high-grade biochar suitable for substitution of fossil fuels. Crucially, the net calorific value of biochar processed at 350 °C substantially exceeded that of brown coal. An economic analysis was carried out on the assumption of the current economic reality in the Czech Republic. It was shown that even if the price of the biochar slightly increased, it would still be beneficial to invest in torrefaction technology over paying carbon credits.

Integration of biochar with nitrogen in acidic soil: A strategy to sequester carbon and improve the yield of stevia via altering soil properties and nutrient recycling

The health of agroecosystems is subsiding unremittingly, and the over-use of chemical fertilizers is one of the key reasons. It is hypothesized that integrating biochar, a carbon (C)-rich product, would be an effective approach to reducing the uses of synthetic fertilizers and securing crop productivity through improving soil properties and nutrient cycling. The bamboo biochar at different quantities (4-12 Mg ha-1) and combinations with chemical fertilizers were tested in stevia (Stevia rebaudiana) farming in silty clay acidic soil. The integration of biochar at 8 Mg ha-1 with 100% nitrogen (N), phosphorus (P), and potassium (K) produced statistically (p ≤ 0.05) higher leaf area index, dry leaf yield, and steviol glycosides yield by about 18.0-33.0, 25.8-44.9, and 20.5-59.4%, respectively, compared with the 100% NPK via improving soil physicochemical properties. Soil bulk density was reduced by 5-8% with biochar at ≥ 8 Mg ha-1, indicating the soil porosity was increased by altering the soil macrostructure. The soil pH was significantly (p ≤ 0.05) augmented with the addition of biochar alone or in the combination of N because of the alkaline nature of the used biochar (pH = 9.65). Furthermore, integrating biochar at 8 Mg ha-1 with 100% NPK increased 22.7% soil organic C compared with the sole 100% NPK. The priming effect of applied N activates soil microorganisms to mineralize the stable C. Our results satisfy the hypothesis that adding bamboo biochar would be a novel strategy for sustaining productivity by altering soil physicochemical properties.

Low cost maize stover biochar as an alternative to inorganic fertilizer for improvement of soil chemical properties, growth and yield of tomatoes on degraded soil of Northern Uganda

BACKGROUND

Soil fertility decline due to nutrient mining coupled with low inorganic fertilizer usage is a major cause of low crop yields across sub-Saharan Africa. Recently, biochar potential to improve soil fertility has gained significant attention but there are limited studies on the use of biochar as an alternative to inorganic fertilizers. In this study, we determined the effect of maize stover biochar without inorganic fertilizers on soil chemical properties, growth and yield of tomatoes (Solanum lycopersicum L.). A field experiment was conducted in 2022 for two consecutive seasons in Northern Uganda. The experiment included five treatments; inorganic fertilizer (control), biochar applied at rates of 3.5, 6.9, 13.8 and 27.6 t ha-1.

RESULTS

In this study, maize stover biochar improved all the soil chemical properties. Compared to the control, pH significantly increased by 27% in the 27.6 t ha-1 while total N increased by 35.6% in the 13.8 t ha-1. Although P was significantly low in the 3.5 t ha-1, 6.9 t ha-1 and 13.8 t ha-1, it increased by 3.9% in the 27.6 t ha-1. Exchangeable K was significantly increased by 42.7% and 56.7% in the 13.8 t ha-1 and 27.6 t ha-1 respectively. Exchangeable Ca and Mg were also higher in the biochar treatment than the control. Results also showed that plant height, shoot weight, and all yield parameters were significantly higher in the inorganic fertilizer treatment than in the 3.5, 6.9, and 13.8 t ha-1 treatments. Interestingly, maize stover biochar at 27. 6 t ha-1 increased fruit yield by 16.1% compared to the control suggesting it could be used as an alternative to inorganic fertilizer.

CONCLUSIONS

Maize stover biochar applied at 27.6 t ha-1 improved soil chemical properties especially pH, N, P and K promoting growth and yield of tomatoes. Therefore, maize stover biochar could be recommended as an alternative to expensive inorganic fertilizers for tomato production in Northern Uganda.

Palladium Nanoparticles Grafted onto Phytochemical Functionalized Biochar: A Sustainable Nanozyme for Colorimetric Sensing of Glucose and Glutathione

The devising and development of numerous enzyme mimics, particularly nanoparticles and nanomaterials (nanozymes), have been sparked by the inherent limitations imposed by natural enzymes. Peroxidase is one of the enzymes that is extensively utilized in commercial, medical, and biological applications because of its outstanding substrate selectivity. Herein, we present palladium nanoparticles grafted on Artocarpus heterophyllus (jackfruit) seed-derived biochar (BC-AHE@Pd) as a novel nanozyme to imitate peroxidase activity en route to the rapid and colorimetric detection of H2O2, exploiting o-phenylenediamine as a peroxidase substrate. The biogenically generated BC-AHE@Pd nanocatalyst was synthesized utilizing Artocarpus heterophyllus seed extract as the reducing agent for nanoparticle formation, while the residue became the source for biochar. Various analytical techniques like FT-IR, GC-MS, FE-SEM, EDS, TEM, SAED pattern, p-XRD, and ICP-OES, were used to characterize the BC-AHE@Pd nanocatalyst. The intrinsic peroxidase-like activity of the BC-AHE@Pd nanocatalyst was extended as a prospective nanosensor for the estimation of the biomolecules glucose and glutathione. Moreover, the BC-AHE@Pd nanocatalyst showed recyclability up to three recycles without any significant loss in activity.

Reviewing the role of biochar in paddy soils: An agricultural and environmental perspective

The main challenge of the twenty-first century is to find a balance between environmental sustainability and crop productivity in a world with a rapidly growing population. Soil health is the backbone of a resilient environment and stable food production systems. In recent years, the use of biochar to bind nutrients, sorption of pollutants, and increase crop productivity has gained popularity. This article reviews key recent studies on the environmental impacts of biochar and the benefits of its unique physicochemical features in paddy soils. This review provides critical information on the role of biochar properties on environmental pollutants, carbon and nitrogen cycling, plant growth regulation, and microbial activities. Biochar improves the soil properties of paddy soils through increasing microbial activities and nutrient availability, accelerating carbon and nitrogen cycle, and reducing the availability of heavy metals and micropollutants. For example, a study showed that the application of a maximum of 40 t ha-1 of biochar from rice husks prior to cultivation (at high temperature and slow pyrolysis) increases nutrient utilization and rice grain yield by 40%. Biochar can be used to minimize the use of chemical fertilizers to ensure sustainable food production.

Diclofenac-Impregnated Mesoporous Carbon-Based Electrode Material for the Analysis of the Arsenic Drug Roxarsone

This paper describes a novel electrode material, diclofenac-impregnated mesoporous carbon modified with a cationic surfactant, cetyltrimethylammonium bromide (DF-CMK-3/CTAB), for ultratrace analysis of the arsenic drug roxarsone (ROX). DF-CMK-3 amorphous carbon is a material with a high specific surface area and well-defined, hexagonally ordered, thin mesopores. The functional groups attached to the carbonaceous surface, such as chromene and pyron-like oxygen groups, lactam, and aromatic carbon rings, have the basic character and they can donate electrons. Modification of DF-CMK-3 with a CTAB layer significantly increases the analytical signal due to electrostatic interactions between the cationic surfactant and the anion form of ROX in the acidic medium. The voltammetric procedure at the glassy carbon sensor modified with DF-CMK-3/CTAB exhibited excellent sensitivity (limit of detection of 9.6 × 10-11 M) with a wide range of linearity from 5.0 × 10-10 to 1.0 × 10-4 M. Analysis of real samples (treated municipal wastewater and river water) showed recoveries from 96 to 102% without applying the complicated sample pretreatment step. The sensor demonstrated excellent sensitivity in the analysis of the arsenic drug ROX in the presence of interferences in environmental water samples.

Biochar production from cellulose under reductant atmosphere: influence of the total pyrolysis time

Today's rising energy costs, coupled with increasing energy demand, make it necessary to search for more efficient energy processes. In recent years, there have been increasing efforts to develop efficient catalysts based on waste-derived char, by a single step where the carbon precursor and the metallic active phase one undergo a single common thermal process under a reductant atmosphere at high temperature. The use of a reductant atmosphere drives the formation of carbonaceous materials with different characteristics than those obtained under the standard nitrogen-inert one. Our work evaluates the influence of the residence time and the heating rate on the physicochemical properties of the biochar obtained. Relatively long residence times and slow heating rates, improve the yield to the resulting biochar, without increasing production cost, making the subsequent char-based metallic catalyst synthesis more efficient. The heating rate was shown to be key in improving the properties of the char in a smoother and more controlled way, unlocking a new working pathway for the efficient design and production of char-based catalysts in a one-pot synthesis.

Effect of continuous sugarcane bagasse-derived biochar application on rainfed cotton (Gossypium hirsutum L.) growth, yield and lint quality in the humid Mississippi delta

Optimizing soil health through soil amendments is a promising strategy for enhancing rainwater efficiency for stabilizing crop production. Biochar, obtained by torrefaction of sugarcane bagasse, a byproduct from sugar mills, has a high potential for its use as a soil amendment, which can boost crop yields, but needs further field trials for its adoption in farming systems. A field study was conducted during 2019-2021 at Stoneville, Mississippi, to assess rainfed cotton (Gossypium hirsutum L.) production under four biochar levels (0, 10, 20, and 40 t ha-1) on Dundee silt loam soil. The effects of biochar on cotton growth and lint yield and quality were examined. Biochar levels had no significant impact on cotton lint and seed yield for the first two years. Still, in the third year, a significant increase in lint yield by 13 and 21.7% was recorded at 20 and 40 t ha-1 biochar levels, respectively. In the third year, lint yields were 1523, 1586, 1721, and 1854 kg ha-1 at 0, 10, 20 and 40 t ha-1 biochar levels, respectively. Similarly, cotton seed yield increased by 10.8% and 13.4% in 20 and 40 t ha-1 biochar plots. This study demonstrated that successive biochar applications at 20 or 40 t ha-1 can enhance cotton lint and seed yields under rainfed conditions. These improved yields with biochar did not produce increased net returns due to the increased production costs. Many lint quality parameters were unaffected except for micronaire, fiber strength and fiber length. However, potential long-term benefits of enhanced cotton production from biochar application beyond the length of the study merit further investigation. Additionally, biochar application is more relevant when accrued carbon credits through carbon sequestration outweigh the increased production costs due to biochar application.

Interactions between white and black carbon in water: A case study of concurrent aging of microplastics and biochar

Microplastics and biochar, as particulate matter that is prevalent in the water environment, will inevitably encounter and interact with each other during environmental aging. The potential interaction of microplastics and biochar, and the associated impact on their environmental behavior remains largely unknown. In this study, we exposed microplastics and biochar concurrently to ultraviolet light to mimic the aging process, investigated the release and fluorescence characteristics of dissolved organic matter (DOM) in water, and analyzed the effects of co-existing microplastics and biochar on their sorption of organic contaminants. We demonstrate that early-stage interactions of microplastics and biochar could entangle to promote the release of DOM from biochar, while their long-term interactions after light irradiation resulted in the sorption of hydrophobic and small molecules of microbial byproduct-like DOM. Simultaneously, early-stage interactions of microplastics and biochar showed a promotion for sorption of organic contaminants with an increase of 5.3-17.7%. After aging, however, long-term interactions between microplastics and biochar made it no longer promote the sorption of organic contaminants due to the influence of heterogeneous aggregation. Our results provide new insights into the time-dependent interactions between microplastics and biochar and highlight the need to incorporate their interactions into future environmental risk assessments for microplastics in the water environment.

Biosolids-derived fertilisers: A review of challenges and opportunities

Soil application of biosolids as an organic fertiliser continues to be a cost-effective way to beneficially utilise its carbon and nutrient contents to maintain soil fertility. However, ongoing concerns over microplastics and persistent organic contaminants means that land-application of biosolids has come under increased scrutiny. To identify a way forward for the ongoing future use of biosolids-derived fertilisers in agriculture, the current work presents a critical review of: (1) contaminants of concern in biosolids and how regulatory approaches can address these to enable on-going beneficial reuse, (2) nutrient contents and bioavailability in biosolids to understand agronomic potential, (3) developments in extractive technologies to preserve and recover nutrients from biosolids before destructive dissipation when the biosolids are thermally processed to deal with persistent contaminants of concern (e.g. microplastics), and (4) use of the recovered nutrients, and the biochar produced by thermal processing, in novel organomineral fertilisers that match specific equipment, crop and soil requirements of broad-acre cropping. Several challenges were identified and recommendations for prioritisation of future research and development are provided to enable safe beneficial reuse of biosolids-derived fertilisers. Opportunities include more efficient technologies to preserve, extract and reuse nutrients from sewage sludge and biosolids, and the production of organomineral fertiliser products with characteristics that enable reliable widespread use across broad-acre agriculture.

Activation persulfate for efficient tetrabromobisphenol A degradation via carbon-based materials: Synergistic mechanism of doped N and Fe

In this study, a novel carbon-based material (Fe-N-PGWBC) utilizing the garden waste, melamine and FeSO₄ as the precursor was successfully synthesized, efficiently activating peroxydisulfate (PDS) to degrade tetrabromobisphenol A (TBBPA). Under typical conditions (Fe-N-PGWBC dose of 100 mg·L^-1, PDS of 0.2 mM and TBBPA of 10 mg·L^-1), Fe-N-PGWBC/PDS system could achieve over 99% TBBPA removal (including adsorption and degradation) within 60 min, and the corresponding rate constant k_s was 0.0724 min^-1, which was almost 40.2 times higher than that of the pristine biochar. The extraction experiments implied that the excellent adsorption performance of Fe-N-PGWBC did not hinder the degradation of TBBPA. Abundant active sites (rich oxygen-containing functional groups, Fe-O and Fe₃C) of Fe-N-PGWBC could effectively promote PDS decomposition to produce reactive oxygen species. The probe-based kinetic modelling methods verified that approximately 87.6% TBBPA was degraded by SO₄^·-, 12.2% TBBPA was degraded by ¹O₂, and 0.2% TBBPA was degraded by ^·OH. Furthermore, based on the calculation of density functional theory and identification of products, TBBPA was mainly involved in three transformation pathways including hydroxylation, debromination and β-scission process. The study proposed a facile resource approach of garden waste and provided deeper understanding for the TBBPA degradation mechanisms in heterogeneous system.

The importance of presoaking to improve the efficiency of MgCl2-modified and non-modified biochar in the adsorption of cadmium

Investigating the effect of presoaking, as one of the most important physical factors affecting the adsorption behavior of biochar, on the adsorption of heavy metals by modified or non-modified biochar and presoaking mechanism is still an open issue. In this study, the water presoaking effect on the kinetics of cadmium (Cd) adsorption by rice husk biochar (produced at 450 °C, B1, and at 600 °C, B2) and the rice husk biochar modified with magnesium chloride (B1 modified with MgCl₂, MB1, and B2 modified with MgCl₂, MB2) was investigated. Furthermore, the effect of pH (2, 5, and 6), temperature (15, 25, and 35 °C), and biochar particle size (100 and 500 µm) on the kinetics of Cd adsorption was also investigated. Results revealed that the content of Cd adsorbed by the presoaked biochar was significantly higher than that by the non-presoaked biochar. The highest Cd adsorption capacity of MB2 and MB1 was 98.4 and 97.6 mg g^-1, respectively, which was much better than that of B1 (7.6 mg g^-1) and B2 (7.5 mg g^-1). The modeling of kinetics results showed that in all cases pseudo-second-order model was well-fitted (R²>0.99) with Cd adsorption data. The results also indicated that the highest Cd adsorption values were observed at pH 6 in presoaked MB1 with size of 100 µm as well as at the temperature of 35 °C in presoaked MB2, indicating the optimum conditions for this process. The presoaking process was not affected by biochar size and pH, and the difference in adsorbed Cd content between presoaked biochars and non-presoaked ones was also similar. However, the temperature had a negative effect on presoaking. The presoaking process decreased micropores (<10 µm) in the biochars but had no effect on biochar hydrophobicity. Therefore, presoaking, which could significantly increase Cd adsorption and reduce equilibrium time by reducing the micropores of biochars, is suggested as an effective strategy for improving the efficiency of modified biochars or non-modified ones in the adsorption of contaminants (Cd) from aquatic media.

Abattoir residues as nutrient resources: Nitrogen recycling with bone chars and biogas digestates

Abattoirs produce by-products that may become valuable resources for nutrient recycling and energy generation by including pyrolysis and biogas production in the value creation chain. This study investigated the potential of bone chars as sorbents for ammonium in order to produce a soil amendment useful for fertilizing purposes. Ammonium enriched from the digestate by membrane distillation or from pure ammonium sulphate solutions accommodated the nitrogen sorption to the bone chars. The plant availability of the sorbed nitrogen was studied by a standardized short-term plant test with rye (Secale cereale L.). The results showed that ammonium, both from biogas digestate and from pure salt solutions, could be sorbed successfully to the bone chars post-pyrolysis and increased the nitrogen concentration of the chars (1.6 ± 0.3%) by 0.2-0.4%. This additional nitrogen was desorbed easily and supported plant growth (+17 to +37%) and plant nitrogen uptake (+19-74%). The sorption of ammonium to the bone chars had a positive effect on the reversal of pure bone char phytotoxicity and on nitrogen availability. In summary, this study showed that abattoir wastes are useful pyrolysis input materials to produce bone chars and to provide ammonium source for sorption to the chars. This innovation offers the possibility to produce nitrogen-enriched bone chars as a new type of fertilizer that upgrades the known value of bone char as phosphorus fertilizer by an additional nitrogen fertilizer effect.

Date palm-magnetized biochar for in-situ stabilization of toxic metals in mining-polluted soil: evaluation using single-step extraction methods and phytoavailability

Mining activities provide a pathway for the entry and accumulation of various heavy metals in soil, which ultimately leads to severe environmental pollution. Utilization of various immobilizing agents could restore such contaminated soils. Therefore, in this study, date palm-derived biochars (BCs: produced at 300 °C, 500 °C and 700 °C) and magnetized biochars (MBCs) were employed to stabilize heavy metals (Cd, Pb, Cu and Zn) in mining polluted soil. Metal polluted soil was amended with BCs and MBCs at w/w ratio of 2% and cultivated with wheat (Triticum aestivum L.) in a greenhouse. After harvesting, dry and fresh biomass of plants were recorded. The soil and plant samples were collected, and the concentrations of heavy metals were measured after extracting with water, DTPA (diethylenetriaminepentaacetic acid), EDTA (ethylenediaminetetraacetic acid), and acetic acid. BCs and MBCs resulted in reduced metal availability and uptake, with higher fresh and dry biomass (>36%). MBCs showed maximum decrease (>70%) in uptake and shoot concentration of metals, as these reductions for Cd and Pb reached below the detection limits. Among all single-step extractions, the DTPA-extractable metals showed a significant positive correlation with shoot concentrations of tested metals. Thus, the synthesized BCs and MBCs could effectively be used for stabilizing heavy metals and improve plant productivity in multi-contaminated soils. However, future studies should focus on long term field trials to restore contaminated mining soils using modified biochars.

Pyrolysis temperature influences the capacity of biochar to immobilize copper and arsenic in mining soil remediation

Biochar is a promising material used for multiple remediation approaches, mainly in polluted soils. Its properties can differ depending on feedstock and pyrolysis temperature. In this context, we tested the capacity of three biochar products made from corncob, pyrolyzed at different temperatures (350, 500, and 650 °C), to remediate a mining soil affected by high levels of Cu and As. We performed an exhaustive characterization of the biochar. We found that biochar showed a higher surface area with increasing pyrolysis temperature, whereas high molecular weight PAHs were detected in biochar produced at the maximum temperature, thus indicating potential ecotoxicological risks. After the application of biochar to the soil, Cu was partially immobilized, especially when using that obtained at 500 °C. This effect is attributed to the structure of this material and an increase in soil pH and organic matter content. Conversely, As was increased in the soluble fraction for all three types of biochar but in a proportion that lacks relevance. On the whole, given its lower PAH content, higher Cu immobilization ratio, and an almost negligible increase in As availability, biochar obtained at 500 °C outperformed the other two products with respect to soil recovery. Of note, data on Cu and As availability were doubled-checked using two extraction methodologies. We propose that this operational approach for determining the most suitable pyrolysis temperature will find application in other soil remediation actions.

Mechanochemical modified nitrogen-rich biochar derived from shrimp shell: Dominant mechanism in pyridinic-N for aquatic methylene blue removal

N-doping for the preparation of functional carbon materials is a trending research topic. In this study, N-rich biochar (BC) was prepared by calcining naturally N rich shrimp shells under oxygen-limiting environment, and the calcining temperatures were controlled. BC were activated with 5% hydrochloric acid solutions and then post-modified with ball-milling to obtain a series of novel adsorbents (MBCs). All samples were characterized by SEM, BET, FT-IR, XRD, XPS, TG, and element analysis. Surface area, pore volume, and other surface functional groups were significantly improved after acidizing and ball-milling. The adsorption capacities for MB were MBC350 > MBC500 > MBC650 >BC350 > BC650 > BC500, and the equilibrium adsorption capacities were 575.01 mg/g, 506.52 mg/g, 424.59 mg/g, 113.31 mg/g, 93.53 mg/g and 86.25 mg/g, respectively. The excellent adsorption performance of MBCs for MB was ascribed to Lewis acid-base interaction, π-π interaction, electrostatic interaction and van der Waals, and the quinone group and pyridinic-N on the surface of the MBCs are identified as the major active sites. Taken together, ball-milled shrimp shell biochar is a promising material for cation dye adsorption.

Characteristics and liming potential of biochar types from potato waste and pine-bark

Large amount of wastes are burnt or left to decompose on site or at landfills where they cause air pollution and nutrient leaching to groundwater. Waste management strategies that return these food wastes to agricultural soils recover the carbon and nutrients that would otherwise have been lost, enrich soils and improve crop productivity. This study characterised biochar produced by pyrolysis of potato peels (PP), cull potato (CP) and pine bark (PB) at 350 and 650°C. The biochar types were analysed for pH, phosphorus (P) and other elemental composition. Proximate analysis was done following ASTM standard 1762-84, while surface functional groups and external morphology characteristics were determined using FTIR and SEM; respectively. Pine bark biochar had higher yield and fixed carbon (FC), and lower ash content and volatile matter than biochar types from potato wastes. The liming potential of CP 650°C is greater than that of PB biochars. Biochar types from potato waste had more functional groups even at high pyrolysis temperature relative to pine bark. Potato waste biochars showed an increase in pH, calcium carbonate equivalent (CCE), K and P content with increasing pyrolysis temperature. These findings imply that biochar from potato waste may be valuable for soil C storage, remediating acidity and increasing availability of nutrients especially K and P in acidic soils.

A review on influence of biochar amendment on soil processes and environmental remediation

Biochar is the thermal degradation product of biomass generated in an oxygen-limited environment under different pyrolysis conditions. Biochar characteristics are functions of the feedstock material and pyrolysis temperature. Depending on pyrolysis conditions biochar concentrates varying quantities of recalcitrant and labile carbon along with nutrients which in turn affect soil physiochemical properties and microbial processes. Biochar in soil balances carbon content encourages nitrogen fixation and solubilize phosphorus along with enhancing soil enzyme activity. It serves as a microhabitat for microorganisms present in soil thus influences the diversity, composition, and distribution of soil microbial communities by affecting their intra- and interspecific communication. This review provides an overview of the current knowledge about biochar characteristics, its interactions with soil, and associated biota and its role in soil remediation. In addition, this paper also discussed the factors affecting the capacity of biochar to adsorb organic pollutants following different mechanisms. Being an effective adsorbent due its high specific surface area, large porosity, and numerous surface functional groups biochar has been explored extensively in field of environment to remediate contaminated soils.

Biochar as Sustainable Alternative and Green Adsorbent for the Remediation of Noxious Pollutants: A Comprehensive Review

The current water crisis necessitates the development of new materials for wastewater treatment. A variety of nanomaterials are continuously being investigated for their potential as adsorbents for environmental remediation. Researchers intend to develop a low-cost, simple, and sustainable material that can cater to removal of pollutants. Biochar derived from biowaste is a potential candidate for the existing problem of water pollution. The review focuses on the various aspects of biochar, such as its sources, preparation methods, mechanism, applications for wastewater treatment, and its regeneration. Compared with other adsorbents, biochar is considered as an environmentally friendly, sustainable, and cost-effective substitute for waste management, climate protection, soil improvement, wastewater treatment, etc. The special properties of biochar such as porosity, surface area, surface charge, and functional groups can be easily modified by various chemical methods, resulting in improved adsorption properties. Therefore, in view of the increasing environmental pollution and the problems encountered by researchers in treating pollutants, biochar is of great importance. This review also highlights the challenges and prospective areas that can be explored and studied in more detail in the future.

Decreased in vitro bioaccessibility of Cd and Pb in an acidic Ultisol through incorporation of crop straw-derived biochar

Studies analyzing the in vitro bioaccessibility (BAc) of heavy metals in biochar-amended soils are currently lacking. The present study aimed to assess the metal BAc in Cd- and Pb-spiked acidic Ultisol samples treated individually with 2% (w/w) maize, rice, wheat, soybean, and pea straw-derived biochar. The results indicate that the Cd-BAc simulated in gastric phase (GP) decreased from 78.4% to 66.5-72.3% and the Pb-BAC decreased from 74.3% to 67.2-69.2%; however, the Cd-BAc in the intestinal phase (IP) decreased from 35.6% to 27.9-33.5% and the Pb-BAc decreased from 34.7% to 29.7-32.9% after 120 d of incubation with biochar application compared to the un-amended Ultisol. The Cd- and Pb-BAc in both GP and IP were significantly negatively correlated with soil pH, CEC, and organic carbon (P < 0.05), which increased after biochar application. The soybean straw-derived biochar amendment has the greatest potential to decrease the BAc of Cd and Pb in the GP and IP, owing to the highest level of CEC, SOC, TC and TN among all soil samples. Moreover, the BAc was positively correlated with the exchangeable, and exchangeable + carbonate-bound Cd and Pb fractions (P < 0.05), indicating these fractions had a dominant influence on the BAc of cationic heavy metals. Therefore, crop straw-derived biochar amendment can decrease the BAc of Cd and Pb in acidic Ultisol, and thus mitigate the health risks posed by these metals from incidental ingestion.

Biochar from date palm (Phoenix dactylifera L.) residues—a critical review

Biochar, a carbon rich organic amendment, derived from organic biomass by pyrolysis under high-temperature and zero oxygen condition, is a soil amendment to enrich soil with essential nutrients. Biochar is multidimensional in its benefits, including increase in soil carbon sequestration, reduction in green house emission, improved soil fertility, and prolonged soil moisture retention capability to overcome drought. Biochar can be produced from a wide array of biological residues, contributed by plants as well as animals. Date palm a common plant in Gulf region, leave enormous quantity of residues, which are disposed or burnt as waste in farms, that acts as a source of pollution in date-producing nations. The residual biomass from dates is utilized in cattle feed production in some countries. Disposing these residues without harming the environment is a challenge and the perfect solution is biochar. Based on the unique abatement potential of biochar and its functions to improve soil health and soil carbon sequestration, biochar can be considered as long-term agriculture adaptation strategy. This comprehensive review highlights the production of biochar from date palm biomass, the influence of different date palm parts in biochar production, and their potential benefits to the community. It is realized that the knowledge of biochar from date palm residues is still in its infancy which requires concerted efforts to educate the date palm farming community to utilize the valuable biomass from date palm for transformation to a nutritious and eco-friendly product, biochar.

Integrating Biochar, Bacteria, and Plants for Sustainable Remediation of Soils Contaminated with Organic Pollutants

The contamination of soil with organic pollutants has been accelerated by agricultural and industrial development and poses a major threat to global ecosystems and human health. Various chemical and physical techniques have been developed to remediate soils contaminated with organic pollutants, but challenges related to cost, efficacy, and toxic byproducts often limit their sustainability. Fortunately, phytoremediation, achieved through the use of plants and associated microbiomes, has shown great promise for tackling environmental pollution; this technology has been tested both in the laboratory and in the field. Plant-microbe interactions further promote the efficacy of phytoremediation, with plant growth-promoting bacteria (PGPB) often used to assist the remediation of organic pollutants. However, the efficiency of microbe-assisted phytoremediation can be impeded by (i) high concentrations of secondary toxins, (ii) the absence of a suitable sink for these toxins, (iii) nutrient limitations, (iv) the lack of continued release of microbial inocula, and (v) the lack of shelter or porous habitats for planktonic organisms. In this regard, biochar affords unparalleled positive attributes that make it a suitable bacterial carrier and soil health enhancer. We propose that several barriers can be overcome by integrating plants, PGPB, and biochar for the remediation of organic pollutants in soil. Here, we explore the mechanisms by which biochar and PGPB can assist plants in the remediation of organic pollutants in soils, and thereby improve soil health. We analyze the cost-effectiveness, feasibility, life cycle, and practicality of this integration for sustainable restoration and management of soil.

Biobased Kapok Fiber Nano-Structure for Energy and Environment Application: A Critical Review

The increasing degradation of fossil fuels has motivated the globe to turn to green energy solutions such as biofuel in order to minimize the entire reliance on fossil fuels. Green renewable resources have grown in popularity in recent years as a result of the advancement of environmental technology solutions. Kapok fiber is a sort of cellulosic fiber derived from kapok tree seeds (Ceiba pentandra). Kapok Fiber, as a bio-template, offers the best alternatives to provide clean and renewable energy sources. The unique structure, good conductivity, and excellent physical properties exhibited by kapok fiber nominate it as a highly favored cocatalyst for deriving solar energy processes. This review will explore the role and recent developments of KF in energy production, including hydrogen and CO₂ reduction. Moreover, this work summarized the potential of kapok fiber in environmental applications, including adsorption and degradation. The future contribution and concerns are highlighted in order to provide perspective on the future advancement of kapok fiber.

Surface functional groups and degree of carbonization of selected chars from different processes and feedstock

The knowledge of the structural and chemical properties of biochars is decisive for their application as technical products. For this reason, methods for the characterization of biochars that are generally applicable and allow quality control are highly desired. Several methods that have shown potential in other studies were used to investigate two activated carbons and seven biochars from different processes and feedstock. The chars were chosen to cover a wide range of chemical composition and structural properties as a hardness test for the analytical methods used in this study. Specific problems connected with the pretreatment of samples and drawbacks of some methods for some types of chars could be identified in an integrated consideration of the results from different methods. None of the spectroscopic methods was found to be suitable for the quality control of all types of chars. The most valuable results were obtained by chemical analysis that, however, required the complete determination of the main elements, including that of oxygen, and of inorganic components for adequate results. The combination of X-ray photoelectron spectroscopy (XPS) and FT-IR spectroscopy allows a rough characterization of surface functional groups, but cannot discriminate aliphatic and aromatic OH groups. FT-IR might be a suitable method for the quality control of biochars made at lower temperature. The results of Raman spectroscopy did not well correlate with the amount of sp2 hybridized carbon determined by XPS. A better correlation of XPS data was found with the electrical polarization determined by the method of spectral induced polarization that was used for the first time in conjunction with extensive analytical characterization.

Low bioavailability of derivatives of polycyclic aromatic hydrocarbons in biochar obtained from different feedstock

In the last years, there is great progress in the field of studies on the thermal transformation of wastes into valuable materials such as biochar. High-temperature processes, however, are connected with the formation of polycyclic aromatic hydrocarbons (PAHs) with confirmed toxicity. However, during pyrolysis, some derivatives containing oxygen, nitrogen, or sulfur can also be formed. Their toxicity is expected to be higher than parent PAHs. However, the key parameter in the agricultural application of carbonaceous materials is PAHs' bioavailability. The aim of the presented studies was the determination of the effect of various feedstock (wheat straw (Triticum L.), willow (Salix viminalis), sunflower, residues from softwood and hardwood, sewage sludges, and residues from biogas production) on the formation of PAHs and their derivatives (O-, N-PAHs) in biochar and their bioavailability. The results indicated that the content of total and bioavailable PAHs in obtained biochar was rather low. The concentration of total PAHs in plant-derived biochar reached 57 ± 3 ng g^-1 - 181 ± 8 ng g^-1, whereas sewage sludge-derived biochar contained from 121 ± 6 ng g^-1 to 188 ± 9 ng g^-1 of PAHs. The highest concentration of PAHs was noted in biochar obtained from residues from biochar production - up to 202 ± 9 ng g^-1. The total concentration of bioavailable PAHs was lower and reached 2-4.45 ng L^-1 for plant-derived biochar, 3-40 ng L^-1 for sewage sludge-derived biochar. The highest content of bioavailable PAHs was noted in biochar obtained from residues from biogas production: 9-42 ng L^-1 indicating that increased attention should be paid to using this type of biochar. Among PAHs derivatives, nitronaphthalene, 1-methyl-5-nitronaphthalene, 1-methyl-6-nitronaphthalene, 9,10-anthracenedione, 4H-cyclopenta(def)phenanthrene, nitropyrene were determined at various levels and their concentrations were from below the limit of detection (LOD) to 28 ng L^-1 for plant-derived biochar, 3-16 ng L^-1 for biochar obtained from residues from biogas production, and 5-45 ng L^-1 for sewage sludge-derived biochar. The content of bioavailable PAHs derivatives was, generally, one order of magnitude lower than parent PAHs derivatives, and reached from below LOD up to almost 1 ng L^-1 for plant-derived biochar, from 0.5 to 2 ng L^-1 for biochar obtained from residues from biogas production, and from 0.2 to almost 5 ng L^-1 for sewage sludge-derived biochar confirming the safety of agricultural usage of biochar.

The Role of Nanoengineered Biochar Activated with Fe for Sulfanilamide Removal from Soils and Water

Biochar is a nanoengineered sorbent proposed to control the contamination derived from the presence of residual concentrations of sulfonamides in soil. In this work, we evaluated the sorption of sulfanilamide (SFA) in commercial biochar (BC) produced at 500 °C from oak hardwood (Quercus ilex) and its analog activated with 2% (w/w) Fe (BC-Fe). Subsequently, the effect on dissipation and transport of SFA in untreated soil and soil treated with BC and BC-Fe was also assessed. Laboratory batch studies revealed that BC-Fe increased the sorption of SFA as compared to the pristine BC with Kd of 278 and 98 L/kg, respectively. The dissipation of SFA in either untreated soil or soil treated with BC or BC-Fe was similar, displaying half-lives ranging between 4 and 6.4 days. Conversely, the concurrent determination of sorption during the incubation experiment showed that lower amounts of SFA in solution at the beginning of the experiments were bioavailable in BC-Fe-treated soil when compared to the rest of the treatments shortly after application. Leaching column studies confirmed the amendment’s capability to bind the SFA compound. Therefore, the decrease in bioavailability and movement of SFA in treated soils suggest that biochar soil application can reduce SFA soil and water contamination. According to our results, BC surface modification after Fe activation may be more appropriate for water decontamination than for soil since there were no significant differences between the two types of biochar when added to the soil. Therefore, these outcomes should be considered to optimize the SFA mitigation potential of biochar.

Enhancement of biogas production from individually or co-digested green algae Cheatomorpha linum using ultrasound and ozonation treated biochar

This paper proposes the use of modified biochar, derived from Sawdust (SD) biomass using sonication (SSDB) and Ozonation (OSDB) processes, as an additive for biogas production from green algae Cheatomorpha linum (C. linum) either individually or co-digested with natural diet for rotifer culture (S. parkel). Brunauer-Emmett-Teller (BET), Fourier-Transform Infrared (FTIR), thermal-gravimetric (TGA), and X-ray diffraction (XRD) analyses were used to characterize the generated biochar. Ultrasound (US) specific energy, dose, intensity and dissolved ozone (O₃) concentration were also calculated. FTIR analyses proved the capability of US and ozonation treatment of biochar to enhance the biogas production process. The kinetic model proposed fits successfully with the data of the experimental work and the modified Gompertz models that had the maximum R² value of 0.993 for 150 mg/L of OSDB. The results of this work confirmed the significant impact of US and ozonation processes on the use of biochar as an additive in biogas production. The highest biogas outputs 1059 mL/g VS and 1054 mL/g VS) were achieved when 50 mg of SSDB and 150 mg of OSDB were added to C. linum co-digested with S. parkle.

Physical-Chemical Characterization of Different Carbon-Based Sorbents for Environmental Applications

Biochar has been used in various applications, e.g., as a soil conditioner and in remediation of contaminated water, wastewater, and gaseous emissions. In the latter application, biochar was shown to be a suitable alternative to activated carbon, providing high treatment efficiency. Since biochar is a by-product of waste pyrolysis, its use allows for compliance with circular economics. Thus, this research aims to obtain a detailed characterization of three carbonaceous materials: an activated carbon (CARBOSORB NC 1240^®) and two biochars (RE-CHAR^® and AMBIOTON^®). In particular, the objective of this work is to compare the properties of three carbonaceous materials to evaluate whether the application of the two biochars is the same as that of activated carbon. The characterization included, among others, particle size distribution, elemental analysis, pH, scanning electron microscope, pore volume, specific surface area, and ionic exchange capacity. The results showed that CARBOSORB NC 1240^® presented a higher specific surface (1126.64 m²/g) than AMBIOTON^® (256.23 m²/g) and RE-CHAR^® (280.25 m²/g). Both biochar and activated carbon belong to the category of mesoporous media, showing a pore size between 2 and 50 nm (20-500 Å). Moreover, the chemical composition analysis shows similar C, H, and N composition in the three carbonaceous materials while a higher O composition in RE-CHAR^® (9.9%) than in CARBOSORB NC 1240 ^® (2.67%) and AMBIOTON^® (1.10%). Differences in physical and chemical properties are determined by the feedstock and pyrolysis or gasification temperature. The results obtained allowed to compare the selected materials among each other and with other carbonaceous adsorbents.

How Biochar Derived from Pond Cypress (Taxodium Ascendens) Evolved with Pyrolysis Temperature and Time and Their End Efficacy Evaluation

Biomass type, pyrolysis temperature, and duration can affect biochar properties simultaneously. To further clarify the mechanism of this interaction, the branch and leaf parts of Pond cypress (Taxodium ascendens) were separately pyrolyzed at four peak temperatures (350 °C, 450 °C, 650 °C, and 750 °C) for three different durations (0.5 h, 1 h, and 2 h) in this study. The resulting biochar properties were measured, which included the yield, specific surface area (SSA), pH, EC (electricity conductivity), the bulk and surface elemental composition, and the contents of moisture, ash, fixed carbon, and volatile matter. The results showed that the pyrolysis temperature was more determinant for the modification of all biochar, but the residence time had a significant effect on the yield, pH, and SSA of branch-based biochar (B-biochar) at specific temperatures. However, such a phenomenon only happened on the pH of leaf-based biochar (L-biochar). Results: (1) With the temperature at 350 and 650 °C, the residence time had a significant effect on the yield of B-biochar. (2) The pH of B-biochar and L-biochar varied considerably between durations when the heating temperature hit 650 and 750 °C. (3) The SSA of B-biochar possessed an obvious fluctuation with the time during the pyrolysis from 650 to 750 °C. According to the properties measured above, the principal component and the cluster analysis classified the 24 types of biochar made in this experiment into four groups and revealed that an obvious disparity existed between B-biochar and L-biochar that were pyrolyzed at temperatures ranging from 450 to 750 °C, which suggested that biomass type was the primary factor for biochar-making. All this information can provide valuable references for the optimization of biochar-making in the real world.

Current trends in production, morphology, and real-world environmental applications of biochar for the promotion of sustainability

Biochar has sparked a lot of interest in recent years for various applications such as contaminant removal, carbon sequestration and soil amendment. However, laboratory scale studies dominates over the real-world applications. In this study, we first enumerated on the various ongoing uses of biochar along with adsorption mechanism; and then identified the most suitable source, and efficient method for biochar production; and finally proposed real-world practical applications of biochar as an additive to control diffuse micropollutant pollution along the highways and railway tracks; as well as the pollution through agricultural runoff. We demonstrated that directly or indirectly, biochar can definitely help to achieve all the 17 Sustainable Development Goals. The study on the practical use of biochar is an emerging area, because a lot of research needs are there to realise the full-potential of biochar with ways of attaining sustainable development goals towards waste, energy and pollution management.

Aggregation kinetics of biochar nanoparticles in aqueous environment: Interplays of anion type and bovine serum albumin

The colloidal particles, especially those at the nanoscale, are the most active part of the pyrogenic carbon (biochar). Increasingly applied biochar has resulted in a large number of biochar nanoparticles (NPs) being released into the environment. The aggregation of biochar NPs affects their environmental behavior and fate. The complex effects of anion type (Cl^-, SO₄^2-) and protein (bovine serum albumin, BSA) on the aggregation of wheat straw biochar (WB) and pinewood biochar (PB) NPs in solutions were investigated by the time-resolved dynamic light scattering method. The critical coagulation concentration (CCC) of WB and PB NPs in Na₂SO₄ solution was higher than their CCCs in NaCl solution, which was consistent with the Hofmeister series that SO₄^2-, a kosmotrope anion, increased the interaction between water molecules, thus enhancing the hydrophobic interactions between biochar NPs in solution and promoting their aggregation, while Cl^-, a chaotropic agent, exhibited the opposite effect. When BSA was added into the solution, BSA was adsorbed on the surface of biochar NPs and BSA corona was formed, which inhibited the aggregation of biochar NPs by inducing steric force. The enhanced stability of biochar NPs by BSA was more significant in NaCl than in Na₂SO₄ solution because BSA corona had a more negatively charged surface and a more steric structure in NaCl solution, thus generating stronger electrical repulsion and steric hindrance. The classical DLVO theory and the XDLVO theory incorporating the steric repulsion (in the presence of BSA) were used to interpret the aggregation and dispersion of biochar NPs. Through this study, we found that anion type indirectly affected the aggregation of biochar NPs by influencing the interaction between water molecules, while the aggregation of BSA-biochar NPs conjugates is mainly influenced by the surface charge and structure of BSA corona.

Overview of the use of biochar from main cereals to stimulate plant growth

The total global food demand is expected to increase up to 50% between 2010 and 2050; hence, there is a clear need to increase plant productivity with little or no damage to the environment. In this respect, biochar is a carbon-rich material derived from the pyrolysis of organic matter at high temperatures with a limited oxygen supply, with different physicochemical characteristics that depend on the feedstock and pyrolysis conditions. When used as a soil amendment, it has shown many positive environmental effects such as carbon sequestration, reduction of greenhouse gas emissions, and soil improvement. Biochar application has also shown huge benefits when applied to agri-systems, among them, the improvement of plant growth either in optimal conditions or under abiotic or biotic stress. Several mechanisms, such as enhancing the soil microbial diversity and thus increasing soil nutrient-cycling functions, improving soil physicochemical properties, stimulating the microbial colonization, or increasing soil P, K, or N content, have been described to exert these positive effects on plant growth, either alone or in combination with other resources. In addition, it can also improve the plant antioxidant defenses, an evident advantage for plant growth under stress conditions. Although agricultural residues are generated from a wide variety of crops, cereals account for more than half of the world's harvested area. Yet, in this review, we will focus on biochar obtained from residues of the most common and relevant cereal crops in terms of global production (rice, wheat, maize, and barley) and in their use as recycled residues to stimulate plant growth. The harvesting and processing of these crops generate a vast number and variety of residues that could be locally recycled into valuable products such as biochar, reducing the waste management problem and accomplishing the circular economy premise. However, very scarce literature focused on the use of biochar from a crop to improve its own growth is available. Herein, we present an overview of the literature focused on this topic, compiling most of the studies and discussing the urgent need to deepen into the molecular mechanisms and pathways involved in the beneficial effects of biochar on plant productivity.

Electrically Conductive and Antimicrobial Agro-Food Waste Biochar Functionalized with Zinc Oxide Particles

Carbonaceous materials derived from biomass have been used as sustainable platforms for the growth of ZnO particles aiming the production of functional composite fillers. Kidney-bean pods were pyrolyzed by applying an experimental design that demonstrates that the specific surface area (S_BET) of biochar is improved with increasing pyrolysis temperature combined with a short air-oxidation time. Meanwhile, the graphitization degree and the electrical conductivity (EC) of biochars were negatively affected by increasing the air-oxidation time. The biochar sample with the higher EC and the one with the higher S_BET were selected to be functionalized with ZnO particles by a solvothermal methodology, obtaining composites with an EC and S_BET properties superior to the ZnO-rGO composite, in addition to a similar antibacterial activity. The developed ZnO-biochar composite structures, which are more ecological and biocompatible than the ZnO composites derived from graphene sheets, can be applied as electrically conductive and active fillers.

Adsorption of As(III) and As(V) from aqueous solution by magnetic biosorbents derived from chemical carbonization of pea peel waste biomass: Isotherm, kinetic, thermodynamic and breakthrough curve modeling studies

The purpose of this research was to investigate the adsorption of arsenic (As) from aqueous solutions using MPAC-500 and MPAC-600 (magnetic-activated carbons synthesized from the peel of Pisum sativum (pea) pyrolyzed at 500 °C and 600 °C temperatures, respectively). The potential of both biosorbents for As adsorption was determined in batch and column mode. The characterization of both biosorbents was performed by energy dispersive spectroscopy, scanning electron microscope, pHZPC, particle size distribution, X-ray diffraction, zeta potential and Fourier-transform infrared spectroscopy. It was found that the efficiency of MPAC-600 was better than MPAC-500 for the adsorption of As(III) and As(V) ions. The adsorption capacities of MPAC-500 and MPAC-600 in removing As(III) were 0.7297 mg/g and 1.3335 mg/g, respectively, while the values of Qmax for As(V) on MPAC-500 and MPAC-600 were 0.4930 mg/g and 0.9451 mg/g, respectively. The Langmuir isotherm model was found to be the best fit for adsorption of As(III) by MPAC-500 and MPAC-600, as well as adsorption of As(V) by MPAC-500. The Freundlich isotherm model, on the other hand, was optimal for As(V) removal with MPAC-600. With R2 values close to unity, the pseudo-second-order kinetics were best fitted to the adsorption process of both As species. The Thomas model was used to estimate the breakthrough curves. The effects of coexisting oxyanions and regeneration studies were also carried out to examine the influence of oxyanions on As adsorption and reusability of biosorbents.

Biochar alters chemical and microbial properties of microplastic-contaminated soil

The occurrence of microplastics (MPs) in soils can negatively affect soil biodiversity and function. Soil amendments applied to MP-contaminated soil can alter the overall soil properties and enhance its functions and processes. However, little is known about how soil amendments improve the quality of MP-contaminated soils. Thus, the present study used a microcosm experiment to explore the potential effects of four types of biochar on the chemical and microbial properties of low-density polyethylene (LDPE) MP-contaminated soil under both drought and well-watered conditions. The results show that the biochars altered soil pH, electrical conductivity (EC), available phosphorous, and total exchangeable cations (TEC) with some variability depending on the biochar type. Oilseed rape straw (OSR)-derived biochars increased soil pH, EC, and TEC under both water conditions with the highest values of 7.94, 0.54 dS m^-1 and 22.0 cmol₍₊₎ kg^-1, respectively. Soil enzyme activities varied under all treatments; in particular, under drought conditions, the fluorescein diacetate activity increased in soils with high temperature (700 °C) biochar. The application of soft wood pellet biochar (700 °C) to MP-contaminated soil increased urease activity by 146% under well-watered conditions. OSR-derived biochars significantly reduced soil acid phosphatase activity under both water conditions. With biochar supplementation, the diversity indices of the bacterial community increased in well-watered soil but not in soil under drought conditions. The abundance of bacterial phyla, such as Firmicutes, Proteobacteria, Actinobacteria, Dictyoglomi, and Gemmatimonadetes, was relatively high in all treatments. Biochar application resulted in negligible variations in bacterial communities under drought conditions but significant variations under well-watered conditions. The findings of this study imply that biochar can be used as a soil amendment to improve the overall soil quality of MP-contaminated soil, but its impact varies depending on the pyrolysis feedstock and temperature. Thus, selecting a suitable biochar is important for improving the soil quality in MP-contaminated soils.