Green Synthesis of Spinel Magnetite Iron Oxide Nanoparticles

Iron oxide nanoparticles as efficient adsorbents for malachite green dye removal: Isotherms, kinetics, and thermodynamics analysis

The presence of dye contamination in waterbodies has emerged as a widespread environmental issue and poses a significant threat to the well-being of humans and the aquatic ecosystem. Nanotechnology has emerged as a promising field in tackling dye pollution. Nanomaterials such as iron oxide nanoparticles have gained considerable interest for potential applications in treating dye-contaminated wastewater. Hence, the current work focuses on the synthesis of iron oxide nanoparticles (FMNP) using the chemical co-precipitation method and its adsorptive performance for removing malachite green (MG) dye from wastewater. The synthesized FMNP was characterized using SEM-EDS, XRD, FTIR, BET, TGA, and Raman analysis. As obtained from SEM and XRD analysis, the FMNP has cubic crystals with an average crystal size of 8.0 nm and a crystallinity of 78.643%. The average pore size, specific surface area, and micropore volume were 4.217 nm, 172.548 m2.g-1, and 0.342 cm3.g-1, respectively. Batch adsorption studies revealed that MG dye adsorption was sensitive to solution pH, initial MG dye concentration, contact time, dosage, and temperature. Under optimum conditions of pH 12, MG dye concentration 50 mg.L-1, contact time 90 min, dosage of 0.2 g.L-1, and at 328.15 K, a maximum removal of 98.814% was attained with a maximum adsorption capacity of 606.06 mg.g-1. MG dye adsorption best fits the Langmuir isotherm and pseudo-second-order kinetics. The economically feasible reusability of the synthesized FMNP is demonstrated by its consistent performance across several cycles. The results demonstrate the significance of using this mesoporous FMNP as an adsorbent for effectively treating dye wastewater.

Green synthesis of CaO-Fe₃O₄ composites for photocatalytic degradation and adsorption of synthetic dyes

The efficient removal of synthetic dyes, such as methylene blue (MB) and malachite green (MG), continues to pose a significant challenge due to their high stability, toxicity, and resistance to conventional treatment methods. In this study, CaO-Fe₃O₄ compounds were synthesized using a sustainable ball-milling technique, utilizing calcium oxide derived from eggshells and Fe₃O₄. The compounds were calcined at temperatures ranging from 200 to 800 °C to optimize their structural and photocatalytic properties. The sample calcined at 400 °C exhibited the highest surface area (17.86 m2/g), the narrowest bandgap (2.10 eV), and the coexistence of CaO, Ca(OH)₂, and γ-Fe₂O₃ phases, making it an ideal candidate for achieving high dye removal efficiency. Under visible light, this sample completely degraded MB at 10 ppm within 30 min, following pseudo-first-order kinetics with a rate constant (kₐₚₚ) of 0.110 min-1 and a half-life (t₁/₂) of 6.30 min. At an MB concentration of 50 ppm, complete degradation was achieved in 90 min. Radical scavenging experiments indicated that superoxide radicals (·O₂-) played a key role in the degradation mechanism. For MG (100 ppm), the maximum adsorption capacity (qₑ) was 1111.11 mg/g, fitting the Langmuir model (R2 = 0.996) with an equilibrium constant (KL) of 0.6822 L/mg, indicating a highly favorable process. The adsorption kinetics followed a pseudo-second-order model (R2 ≈ 0.999), suggesting chemisorption as the rate-limiting step. Thermodynamic parameters confirmed that MG adsorption was spontaneous and endothermic, with negative Gibbs free energy, positive enthalpy, and increased entropy. This study proposes an eco-friendly and efficient approach for dye removal, integrating waste valorization.

The effects of green synthesized anionic cupric oxide nanoparticles on Zaraibi goat spermatozoa during cryopreservation with and without removal of seminal plasma

Sperm motility, normal morphology, viability, spermatozoa DNA damage, and lipid peroxidation are all affected by semen cryopreservation. The goal of this study was to see how effective cupric oxide nanoparticles (CuONPs) are as a cryo-extender additive on post-thawed sperm parameters. An artificial vagina was used to collect semen samples from five mature Zaraibi bucks (2-3 years). Ejaculates were pooled and separated into two fractions (A&B), a fraction (A) was left without being centrifuged and a fraction (B) was centrifuged to remove seminal plasma. Both fractions were diluted with tris egg yolk citrate extender (TECE) and then divided into five equal aliquots, each supplemented with (0, 10, 20, 40, and 60 ppm/ml) CuONPs. The findings revealed that removing seminal plasma before cryopreservation harms sperm parameters. Sperm motility, viability index, membrane integrity, biochemical antioxidant marker, DNA integrity, and MDA level improved after supplementation with CuONPs up to 60 ppm/ml, the most prominent significant positive effect was obtained with the highest dose (60 ppm/ml) without removal of the seminal plasm compared to control group. In conclusion: The presence of seminal plasma with a high concentration of CuONPs (up to 60 ppm/ml) may help to mitigate the negative effects of cryo-preservation.

Iron Oxide Nanoparticles: Green Synthesis and Their Antimicrobial Activity

The rise of antimicrobial resistance caused by inappropriate use of these agents in various settings has become a global health threat. Nanotechnology offers the potential for the synthesis of nanoparticles (NPs) with antimicrobial activity, such as iron oxide nanoparticles (IONPs). The use of IONPs is a promising way to overcome antimicrobial resistance or pathogenicity because of their ability to interact with several biological molecules and to inhibit microbial growth. In this review, we outline the pivotal findings over the past decade concerning methods for the green synthesis of IONPs using bacteria, fungi, plants, and organic waste. Subsequently, we delve into the primary challenges encountered in green synthesis utilizing diverse organisms and organic materials. Furthermore, we compile the most common methods employed for the characterization of these IONPs. To conclude, we highlight the applications of these IONPs as promising antibacterial, antifungal, antiparasitic, and antiviral agents.

Preparation and Characterization of Magnetite-Polyvinyl Alcohol Hybrid Nanoparticles (As-PVA-MNPs) Using Acanthophora spicifera Marine Algae Extract for Enhanced Antimicrobial Activity Against Pathogenic Microorganisms

The present study focused on preparing and characterizing magnetite-polyvinyl alcohol (PVA) hybrid nanoparticles using Acanthophora spicifera marine algae extract as a reducing agent. Various analytical techniques, including UV-Visible spectrometry, Fourier-transform infrared (FTIR) analysis, energy-dispersive X-ray (EDX), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis, were used to characterize the nanoparticles. The results showed the successful synthesis of nanoparticles with a characteristic color change and absorption peak at 400 nm in UV-Visible spectrometry. FTIR analysis indicated an interaction between the carboxyl group and magnetite-polyvinyl alcohol hybrid ions. SEM analysis revealed spherical nanoparticles with sizes ranging from 20 to 100 nm. EDX analysis confirmed the presence of strong magnetite peaks in Acanthophora spicifera, validating successful preparation. XRD analysis indicated the crystalline nature of the nanoparticles. Furthermore, the antimicrobial potential of As-PVA-MNPs was evaluated, demonstrating a significant zone of inhibition against tested bacterial and fungal samples at a concentration of 100 µg. These findings suggest the promising antimicrobial activity of the synthesized nanoparticles for potential applications in combating pathogenic microorganisms.

Modified Graphite Pencil Electrode Based on Graphene Oxide-Modified Fe3O4 for Ferrocene-Mediated Electrochemical Detection of Hemoglobin

This study describes the synthesis of graphene oxide-modified magnetite (rGO/Fe₃O₄) and its use as an electrochemical sensor for the quantitative detection of hemoglobin (Hb). rGO is characterized by a 2θ peak at 10.03° in its X-ray diffraction, 1353 and 1586 cm^-1 vibrations in Raman spectroscopy, while scanning electron microscopy coupled with energy-dispersive spectroscopy of rGO and rGO/Fe₃O₄ revealed the presence of microplate structures in both materials and high presence of iron in rGO/Fe₃O₄ with 50 wt %. The modified graphite pencil electrode, GPE/rGO/Fe₃O₄, is characterized using cyclic voltammetry. Higher electrochemical surface area is obtained when the GPE is modified with rGO/Fe₃O₄. Linear scan voltammetry is used to quantify Hb at the surface of the sensor using ferrocene (FC) as an electrochemical amplifier. Linear response for Hb is obtained in the 0.1-1.8 μM range with a regression coefficient of 0.995, a lower limit of detection of 0.090 μM, and a limit of quantitation of 0.28 μM. The sensor was free from interferents and successfully used to sense Hb in human urine. Due to the above-stated qualities, the GPE/rGO/Fe₃O₄ electrode could be a potential competitive sensor for trace quantities of Hb in physiological media.

CuO nanoleaf and β-cyclodextrin functionalized reduced graphene oxide: a highly selective and sensitive electrochemical sensor for the simultaneous detection of 2-chlorophenol and 2, 4-dichlorophenol

Chlorophenols are considered priority pollutants and are harmful to humans and the environment; consequently, sensitive, and selective detection of chlorophenols is very significant. In the present article, a glassy carbon electrode was modified by copper oxide nanoleaves, β-cyclodextrin, and reduced graphene oxide through an electrostatic self-assembly method (CuO NLs-β-CD-rGO-GCE) and successfully utilized for the selective and sensitive detection of 2-chlorophenol (2-CP) and 2,4-dichlorophenol (2,4-DCP). The modified electrodes were characterized by using SEM, EDX, ATR-FTIR, CV, and EIS. The electrochemical behaviour of 2-CP and 2,4 DCP on different modified electrodes was investigated by cyclic voltammetry whereas differential pulse voltammetry was used for the quantitative determination of chlorophenols. Under the optimized conditions, the anodic peak current displayed a good linear relationship to concentration in the range of 5 to 50 μM for 2-CP and 5 to 30 μM for 2,4-DCP, with detection limits of 0.22 nM and 0.52 nM, respectively. Moreover the proposed sensor exhibited good reproducibility, high sensitivity, and long term stability. To further study the practical applicability of the newly developed sensor, the modified electrode was successfully used to determine 2-CP and 2,4-DCP in a water sample with good recovery.

Rapid Removal of Organic Pollutants from Aqueous Systems under Solar Irradiation Using ZrO2/Fe3O4 Nanoparticles

Pure water scarcity is an emerging, all-around problem that globally affects both the life quality and the world's economy. Heterogeneous photocatalysis under solar irradiation is a promising technique for the organic pollutants (e.g., pesticides, drugs) removal from an aqueous environment. Furthermore, the drawbacks of commercially available photocatalysts can be successfully overcome by using innovative nanoparticles, such as ZrO₂/Fe₃O₄. Four ZrO₂/Fe₃O₄ nanopowders with a different mass ratio of ZrO₂ and Fe₃O₄ were synthesized using the chemical co-precipitation method. XRD analysis showed the presence of magnetite and hematite Fe-oxide phases in all samples. The content of the magnetite phase increased with the addition of 19% ZrO₂. The efficiency of the newly synthesized ZrO₂/Fe₃O₄ nanoparticles was investigated in the rapid removal of selected pollutants under various experimental conditions. Nevertheless, the influence of the water matrix on photocatalytic degradation was also examined. The obtained data showed that using ZrO₂/Fe₃O₄ nanosystems, an appropriate removal rate of the selected pesticides and pharmaceuticals can be reached after 120 min of solar irradiation. Further, the total organic carbon measurements proved the mineralization of the target emerging pollutants. ZrO₂/Fe₃O₄ nanoparticles are economically feasible, as their removal from the suspension can be easily achieved using affordable, environmentally-friendly magnetic separation.

Effect of Magnetized Coagulants on Wastewater Treatment: Rice Starch and Chitosan Ratios Evaluation

Coagulation with synthetic chemicals has been used to treat a wide range of industrial effluents. Herein, the unique characteristics of industrial effluents being detrimental to the environment warrants urgent resource-efficient and eco-friendly solutions. Therefore, the study investigated the use of two magnetized coagulants (chitosan magnetite (CF) and rice starch magnetite (RF)), prepared via co-precipitation in three different ratios (1:2, 1:1 and 2:1) of natural coagulants (chitosan or rice starch) and magnetite nanoparticles (F) as alternative coagulants to alum for the treatment of wastewater. A Brunauer–Emmett–Teller (BET) analyzer, an X-ray diffraction (XRD) analyzer, and energy-dispersive X-ray (EDX) spectroscopy were used to characterize the surface area, crystal structure, and elemental composition of the coagulants. The influences of settling time (10–60 min) on the reduction of turbidity, color, phosphate, and absorbance were studied. This was carried out with a jar test coupled with six beakers operated under coagulation conditions of rapid stirring (150 rpm) and gentle stirring (30 rpm). Wastewater with an initial concentration of 45.6 NTU turbidity, 315 Pt. Co color, 1.18 mg/L phosphate, 352 mg/L chemical oxygen demand (COD), and 73.4% absorbance was used. The RF with a ratio of 1:1 was found to be the best magnetized coagulant with over 80% contaminant removal and 90% absorbance. The treatability performance of RF (1:1) has clearly demonstrated that it is feasible for wastewater treatment.

Green synthesis and characterization of iron-oxide nanoparticles using Moringa oleifera: a potential protocol for use in low and middle income countries

Objective

Green synthesized iron(III) oxide (Fe₃O₄) nanoparticles are gaining appeal in targeted drug delivery systems because of their low cost, fast processing and nontoxicity. However, there is no known research work undertaken in the production of green synthesized nano-particles from the Ugandan grown Moringa Oleifera (MO). This study aims at exploring and developing an optimized protocol aimed at producing such nanoparticles from the Ugandan grown Moringa.

Results

While reducing ferric chloride solution with Moringa oleifera leaves, Iron oxide nanoparticles (Fe₃O₄-NPs) were synthesized through an economical and completely green biosynthetic method. The structural properties of these Fe₃O₄-NPs were investigated by Ultra Violet–visible (UV–Vis) spectrophotometry, X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM). These nanoparticles exhibited UV–visible absorption peaks at 225 nm (nm) for the sixth dilution and 228 nm for the fifth dilution which indicated that the nanoparticles were photosensitive and the SEM study confirmed the spherical nature of these nanoparticles. The total synthesis time was approximately 5 h after drying the moringa leaves, and the average particle size was approximately 16 nm. Such synthesized nanoparticles can potentially be useful for drug delivery, especially in Low and Middle Income Countries (LMICs).

Synthesis and characterization of magnetite carbon nanocomposite from agro waste as chromium adsorbent for effluent treatment

The waste water released from industries which contain pollutants like heavy metals, dyes and other toxic chemicals brings numerous harms to the ecosystem and humans. Nowadays the nanocomposites based technologies are effectively used for environmental remediation. In the present study, hexavalent chromium was removed from the industrial effluent using magnetite carbon nanocomposite. The nanocomposite composed of highly porous carbon and iron oxide nanoparticles prepared by using agrowastes (sugarcane bagasse and orange peel extract). Iron oxide nanoparticles (FeONPs) formation was confirmed by UV-visible spectroscopy; incorporation of magnetite with highly porous carbon was established by Fourier Transforms Infrared Spectroscopy and X-ray Diffraction Spectroscopy. Morphological features of magnetite nanoparticles and highly porous carbon were analyzed using Scanning Electron Microscope and Transmission Electron Microscope. Magnetic properties analyzed by Vibrating Sample Magnetometer revealed magnetite carbon nanocomposite exhibited better Ms value than highly porous carbon. The concentration of Cr⁶⁺ in treated effluent was determined using Atomic Absorption Spectroscopy. Pseudo-second order equation fitted with kinetics and the Langmuir monolayer favors for isotherm. This study reveals efficiency in Cr⁶⁺ removal from effluent using magnetite carbon nanocomposites which extends their application in waste water treatment.

Fe3O4/Graphene Composite Anode Material for Fast-Charging Li-Ion Batteries

Composite anode material based on Fe₃O₄ and reduced graphene oxide is prepared by base-catalysed co-precipitation and sonochemical dispersion. Structural and morphological characterizations demonstrate an effective and homogeneous embedding of Fe₃O₄ nanoparticles in the carbonaceous matrix. Electrochemical characterization highlights specific capacities higher than 1000 mAh g^-1 at 1C, while a capacity of 980 mAhg^-1 is retained at 4C, with outstanding cycling stability. These results demonstrate a synergistic effect by nanosize morphology of Fe₃O₄ and inter-particle conductivity of graphene nanosheets, which also contribute to enhancing the mechanical and cycling stability of the electrode. The outstanding capacity delivered at high rates suggests a possible application of the anode material for high-power systems.

Novel Magnetic Nano Silica Synthesis Using Barley Husk Waste for Removing Petroleum from Polluted Water for Environmental Sustainability

Water contamination by petroleum and its byproducts presents a major challenge worldwide. It is critical that sustainable treatment methods be employed for the removal of such contaminants from polluted water. For this investigation, magnetic nano silica (M-NS) was synthesized using agricultural waste from barley husk using a two-step process that is environmentally friendly and uses green chemistry synthesis. The barley husk waste was used as a precursor for the synthesis of nano-silica following a low energy and sustainable method of acid reflux and heat treatment. Nano-silica was then used for the synthesis of M-NS, with the addition of a magnetic solution of Fe3O4 nanoparticles. The magnetic nano-silica particles were characterized using scanning electron microscopy (SEM), Fourier transform infrared (FTIR), Zeta potential analysis (ZETA) and X-Ray Diffraction (XRD). Magnetic nano-silica particles were observed to have an average diameter of 162 nm and appeared to be hydrophobic, with a large surface area of ~120 m2/gm. Due to these characteristics, magnetic nano-silica was used as an adsorbent for the removal of petrol contaminants from water. The experimental procedure showed that only 0.6 gm. of M-NS was used on 40 mg/L concentration of petroleum and the experiments recorded a high uptake efficiency of 85%. The sorption was shown to be an effective process since a high amount of petroleum was removed. The study further demonstrates that as the amount of sorbent is increased, the sorption capacity also increases until an equilibrium is reached. The results of this study establish that synthesis of M-NS, using environmentally sustainable processes, has the required characteristics to serve as sorbent for petroleum and its byproducts from contaminated water, thus enhancing environmental sustainability.

Green and Traditional Synthesis of Copper Oxide Nanoparticles-Comparative Study

The current study compared the synthesis, characterization and properties of copper oxide nanoparticles (CuO) based on green and traditional chemical methods. The synthesized CuO were confirmed by spectroscopic and morphological characterization such as ultraviolet-visible (UV-vis) spectroscopy, fourier transform infrared (FTIR) spectroscopy, zeta potential, scanning electron microscopy (SEM) and energy dispersed X-ray (EDX). Electrochemical behavior of the modified electrodes was done using cyclic voltammetry (CV) in ferricyanide/ferrocyanide ([Fe(CN)6]4-/[Fe(CN)6]3-) redox probe. As revealed by UV spectrophotometer, the absorption peaks ranged from 290-293 nm for all synthesized nanoparticles. Based on SEM images, CuO were spherical in shape with agglomerated particles. Zeta potential revealed that the green CuO have more negative surface charge than the chemically synthesized CuO. The potential of the green synthesized nanoparticles was higher relative to the chemically synthesized one. Cyclic voltammetry studies indicated that the traditional chemically synthesized CuO and the green CuO have electrocatalytic activity towards the ferricyanide redox probe. This suggests that the green CuO can be modified with other nanomaterials for the preparation of electrochemical sensors towards analytes of interest.

Green synthesis of near-infrared absorbing eugenate capped iron oxide nanoparticles for photothermal application

Nanomaterials exhibit different interesting physical, chemical, electronic and magnetic properties that can be used in a variety of biomedical applications such as molecular imaging, cancer therapy, biosensing, and targeted drug delivery. Among various types of nanoparticles, super paramagnetic iron oxide nanoparticles (SPIONs) have emerged as exogenous contrast agents for in vitro and in vivo deep tissue imaging. Here, we propose a facile, rapid, non-toxic, and cost-effective single step green synthesis method to fabricate eugenate (4-allyl-2-methoxyphenolate) capped iron oxide nanoparticles (E-capped IONPs). The magnetic E-capped IONPs are first time synthesized using a medicinal aromatic plant, Pimenta dioica. The Pimenta dioica leaf extract was used as a natural reducing agent for E-capped IONPs synthesis. The crystalline structure and size of the synthesized spherical nanoparticles were confirmed using the x-ray diffraction and electron microscopic images respectively. In addition, the presence of the functional groups, responsible for capping and stabilizing the synthesized nanoparticles, were identified by the Fourier transform infra-red spectrum. These nanoparticles were found to be safe for human cervical cancer (HeLa) and human embryonic kidney 293 (HEK 293) cell lines and their safety was established using MTT[3-(4, 5-Dimethylthiazol-2-yl)-2, 5-Diphenyltetrazolium Bromide] assay. These green synthesized E-capped IONPs display a distinct absorbance in the tissue transparent near-infrared (NIR) wavelength region. This property was used for the NIR photothermal application of E-capped IONPs. The results suggest that these E-capped IONPs could be used for deep tissue photothermal therapy along with its application as an exogenous contrast agent in biomedical imaging.

Synthesis of 2-deoxy-d-glucose coated Fe3O4 nanoparticles for application in targeted delivery of the Pt(iv) prodrug of cisplatin – a novel approach in chemotherapy

Pt(IV) prodrug of cisplatin was loaded on 2DG functionalized silica coated Fe₃O₄ nanoparticles. The formulation alone exhibited biocompatibility whereas Pt(IV) loaded formulation exhibited cytotoxicity comparable with cisplatin.

Utilization of Neem Leaf Extract on Biosynthesis of Iron Oxide Nanoparticles

The present work reports the successful synthesis of biosynthesized iron oxide nanoparticles (Fe₃O₄-NPs) with the use of non-toxic leaf extract of Neem (Azadirachta indica) as a reducing and stabilizing agent. The successful synthesis was confirmed by infrared spectra analysis with strong peak observed between 400–600 cm⁻¹ that corresponds to magnetite nanoparticles characteristics. X-ray diffraction (XRD) analysis revealed that iron oxide nanoparticles were of high purity with crystalline cubic structure phases in nature. Besides, the average size of magnetite nanoparticles was observed to be 9–12 nm with mostly irregular shapes using a transmission electron microscope (TEM) and was supported by field emission scanning electron microscope (FESEM). Energy dispersive X-ray analysis shown that the elements iron (Fe) and oxygen (O) were present with atomic percentages of 33.29% and 66.71%, respectively. From the vibrating sample magnetometer (VSM) analysis it was proven that the nanoparticles exhibited superparamagnetic properties with a magnetization value of 73 emu/g and the results showed superparamagnetic behavior at room temperature, suggesting potential applications for a magnetic targeting drug delivery system.

Bi2WO6 and FeWO4 Nanocatalysts for the Electrochemical Water Oxidation Process

Polyvinylpyrrolidone (PVP)-assisted nanocatalyst preparation was succeeded by employing a controlled solvothermal route to produce efficient electrodes for electrochemical water-splitting applications. Bi₂WO₆ and FeWO₄ nanocatalysts have been confirmed through the strong signature of (113) and (111) crystal planes, respectively. The binding natures of Bi-W-O and Fe-W-O have been thoroughly discussed by employing X-ray photoelectron spectroscopy which confirmed the formation of Bi₂WO₆ and FeWO₄. The freestanding nanoplate array morphology of Bi₂WO₆ and the fine nanosphere particle morphology of FeWO₄ nanocatalysts were revealed by scanning electron microscopy images. With these confirmations, the fabrication of durable, long-term electrodes for electrochemical water splitting has been subjected to efficient oxidation of water, confirmed by obtaining 2.79 and 1.96 mA/g for 0.5 g PVP-assisted Bi₂WO₆ and FeWO₄ nanocatalysts, respectively. The water oxidation mechanism of both nanocatalysts has been revealed with the support of 24 h stability test over continuous water oxidation and faster charge transfer achieved by the smaller Tafel slope values of 75 and 78 mV/dec, respectively. Generally, these nanocatalysts are utilized for photocatalytic applications. The present study revealed the PVP-assisted synthesis to produce electrocatalytically active nanocatalysts and their electrochemical water-splitting mechanism which will offer a pathway for research interests with regard to the production of multifunctional nanocatalysts for both electro- and photocatalytic applications in the near future.

Green synthesized nanoclusters of ultra-small zero valent iron nanoparticles as a novel dye removing material

Iron based nanoparticles have gained much attention in recent years due to their unique physicochemical properties especially in the environmental remediation practices. There has been an increasing demand for new sustainable techniques for production of these nanoparticles. In the present work, a novel iron nanostructure was successfully fabricated by a facile and green approach using the aqueous extract of Mediterranean cypress (Cupressus sempervirens). In fact, nanoclusters of highly reactive ultra-small (~1.5nm in diameter) iron nanoparticles were constructed. Diameters of iron nanoclusters were measured to be from 9 to 31nm with mean diameter of 19nm. Appearance of the characteristic X-ray diffraction peak of zero valent iron at 2θ=43.5° indicates the great potential of Mediterranean cypress leaf extract for complete reduction of ferric ions. The presence of phytochemicals as organic capping agent was confirmed by IR radiation absorption at 1020cm^-1 and 1623cm^-1 corresponding to the presence of CO and carbonyl groups, respectively. The fabricated nanoclusters also showed a great potential for dye removal from aqueous solution in a time dependent manner. Decolourization efficiency was calculated to be 95% in a 6h process for methyl orange removal. The results of this study suggest the possibility of using iron nanoclusters for future pollutants removal applications from aqueous environments.

Iron and iron oxide nanoparticles are highly toxic to Culex quinquefasciatus with little non-target effects on larvivorous fishes

The control of filariasis vectors has been enhanced in several areas, but there are main challenges, including increasing resistance to insecticides and lack of cheap and eco-friendly products. The toxicity of iron (Fe⁰) and iron oxide (Fe₂O₃) nanoparticles has been scarcely investigated yet. We studied the larvicidal and pupicidal activity of Fe⁰ and Fe₂O₃ nanoparticles against Culex quinquefasciatus. Fe⁰ and Fe₂O₃ nanoparticles produced by green (using a Ficus natalensis aqueous extract) and chemical nanosynthesis, respectively, were analyzed by UV-Vis spectrophotometry, FT-IR spectroscopy, XRD analysis, SEM, and EDX assays. In larvicidal and pupicidal experiments on Cx. quinquefasciatus, LC₅₀ of Fe⁰ nanoparticles ranged from 20.9 (I instar larvae) to 43.7 ppm (pupae) and from 4.5 (I) to 22.1 ppm (pupae) for Fe₂O₃ nanoparticles synthesized chemically. Furthermore, the predation efficiency of the guppy fish, Poecilia reticulata, after a single treatment with sub-lethal doses of Fe⁰ and Fe₂O₃ nanoparticles was magnified. Overall, this work provides new insights about the toxicity of Fe⁰ and Fe₂O₃ nanoparticles against mosquito vectors; we suggested that green and chemical fabricated nano-iron may be considered to develop novel and effective pesticides.

Synthesis and adsorption properties of [Cu(L)2(H2O)]H2[Cu(L)2(P2Mo5O23)]·4H2O/Fe3O4 nanocomposites

Multifunctional [Cu(L)₂(H₂O)]H₂[Cu(L)₂(P₂Mo₅O₂₃)]·4H₂O/Fe₃O₄ (HL = pyridine-2-carboxamide) nanocomposites were successfully synthesized by combining [Cu(L)₂(H₂O)]H₂[Cu(L)₂(P₂Mo₅O₂₃)]·4H₂O and Fe₃O₄ nanoparticles.

Green Synthesis of Magnetite (Fe3O4) Nanoparticles Using Seaweed (Kappaphycus alvarezii) Extract

In this study, a simple, rapid, and eco-friendly green method was introduced to synthesize magnetite nanoparticles (Fe3O4-NPs) successfully. Seaweed Kappaphycus alvarezii (K. alvarezii) was employed as a green reducing and stabilizing agents. The synthesized Fe3O4-NPs were characterized with X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV-Vis), Fourier transform infrared (FT-IR), and transmission electron microscopy (TEM) techniques. The X-ray diffraction planes at (220), (311), (400), (422), (511), (440), and (533) were corresponding to the standard Fe3O4 patterns, which showed the high purity and crystallinity of Fe3O4-NPs had been synthesized. Based on FT-IR analysis, two characteristic absorption peaks were observed at 556 and 423 cm(-1), which proved the existence of Fe3O4 in the prepared nanoparticles. TEM image displayed the synthesized Fe3O4-NPs were mostly in spherical shape with an average size of 14.7 nm.