Preparation of zwitterionically charged nanocrystals by surface TEMPO-mediated oxidation and partial deacetylation of α-chitin

Effects of charge state of nano-chitin on the properties of polyvinyl alcohol composite hydrogel

The present work investigates the effects of nano-chitin with different charge, obtained by acid hydrolysis and TEMPO oxidation, on the structure and properties of borax crosslinked polyvinyl alcohol (PVA) hydrogels. In detail, nano-chitin prepared by acid hydrolysis (ACh) is positively charged (+28.8 mV). The electrostatic attraction between ACh and borax ions leads to a maximum tensile stress of composite hydrogel (ACh/PB), 54.25 KPa, 17 times of the borax crosslinked PVA (PB). In contrast, nano-chitin prepared by TEMPO-oxidation (TCh) shows negative charge (-59.0 mV). Due to the electrostatic repulsion with borax ions, the maximum tensile stress of composite hydrogel (TCh/PB) is only 9.25 KPa, a very limit reinforcing effect. However, TCh/PB showed better self-healing efficiency (96.0 %) as well as ionic conductivity (1.25 × 10-5 S/m). The present work shows that the charge state of the nano-chitin exerts great influence on the interaction with the crosslinking agent borax, therefore, affects the structure and properties of the final PVA composite hydrogels. The results could provide important information about making full use of nano-chitin as a reinforcement by adjusting its surface charge state.

Nanochitin for sustainable and advanced manufacturing

Presently, the rapid depletion of resources and drastic climate change highlight the importance of sustainable development. In this case, nanochitin derived from chitin, the second most abundant renewable polymer in the world, possesses numerous advantages, including toughness, easy processability and biodegradability. Furthermore, it exhibits better dispersibility in various solvents and higher reactivity than chitin owing to its increased surface area to volume ratio. Additionally, it is the only natural polysaccharide that contains nitrogen. Therefore, it is valuable to further develop this innovative technology. This review summarizes the recent developments in nanochitin and specifically identifies sustainable strategies for its preparation. Additionally, the different biomass sources that can be exploited for the extraction of nanochitin are highlighted. More importantly, the life cycle assessment of nanochitin preparation is discussed, followed by its applications in advanced manufacturing and perspectives on the valorization of chitin waste.

pH-responsive Pickering emulsion containing citrus essential oil stabilized by zwitterionically charged chitin nanofibers: Physicochemical properties and antimicrobial activity

In this study, zwitterionic chitin nanofibers (Z-ChNFs) were used to prepare Pickering emulsions containing citrus essential oils (CEO) and their physicochemical properties and antimicrobial activity were investigated. Results show that as-prepared Pickering emulsions exert pH-reversible properties, pH can adjust the charge of Z-ChNFs to influence the stability of the emulsion. As the concentration of Z-ChNFs increase, the droplet size of the emulsion decreases. The high concentration of Z-ChNFs (1.5 wt%) can enhance the viscosity and promote forming nano-network structures within continuous phases, and their amphiphilic nature can strengthen the capacity for adsorption on the oil/water interface, resulting in enhanced physical stability of the encapsulated CEO emulsion. Additionally, Z-ChNFs have positive effects on the improvement of antimicrobial activity of CEO. This study provides valuable implications for the development and application of essential oils as biopreservation in the food field.

Omnidirectional antireflective coatings prepared with chitin nanofibers via layer-by-layer self-assembly

Antireflective coatings play an important role in various optical devices. Herein, we developed omnidirectional antireflective coatings fabricated with charged chitin nanofibers (ChNFs) through layer-by-layer (LbL) self-assembly technology. The charged ChNFs were prepared from chitin with modifications of esterification (negatively charged) and esterification followed partial deacetylation (positively charged), respectively, through ultrasonic treatment. The effects of concentration of the ChNF suspensions and number of bilayers on thickness, refractive index and antireflective capacity of the ChNF coatings were investigated. Refractive index of the ChNF coatings can be manipulated by changing concentration of the ChNF suspensions. Thickness of the ChNF coatings depends on number of bilayers and concentration of the ChNF suspensions. The ChNF coating on a glass substrate with 5 bilayers fabricated using the suspensions with concentration 0.1% had a refractive index of 1.36 and yielded 4% gain in transmittance compared to the glass at the wavelength of 550 nm. This work demonstrates that charged ChNFs are promising building blocks to fabricate antireflective coatings on large size substrates with high efficiency and low cost through LbL self-assembly.

Insights into the relationships of modifying methods, structure, functional properties and applications of chitin: A review

Chitin as the second plentiful polysaccharide has arouse widely attention due to its remarkable availability and biocompatibility. While the strong inter/intra molecular hydrogen bonds and crystallinity severely restrict its applications. Recently, multiple emerging technologies are increasingly used to modify chitin structure for the sake of obtaining excellent functional properties, as well as broadening the corresponding applications. Firstly, this review systematically outlines the features of single and combined methods for chitin modification. Then, the impacts of various modifying methods on the structural characteristics of chitin, including molecular weight, degree of acetylation and functional groups, are further summarized. In addition, the effects of these structural characteristics on the functional properties as well as its potential related applications are illustrated. The conclusion of this review provides better understanding of the relationships among the modifying methods, structure, properties and applications, contributing to chitin modification for the targeted purpose in the future study.

Facile modification of nanochitin in aqueous media for stabilizing tea tree oil based Pickering emulsion with prolonged antibacterial performance

Nanochitins have been explored for preparing Pickering Emulsions, however its application is restricted by its simplex disperse nature. It was hypothesized that zwitterionic nanochitins should be capable of stabilizing oil/water (O/W) interfaces in wider pH range. Furthermore, the control of their size, disperse nature and self-assembly performance suggest the formulation of tunable emulsions. Zwitterionic nanochitins were prepared via Schiff base reaction. A systematic study was performed analyzing the disperse nature, fibril morphology, surface characteristic of modified nanochitins. Oil-in-Water Pickering Emulsions stabilized by modified nanochitins were formulated and emulsion stability was analyzed as function of concentration, pH and self-assembly property and further applied for prolonged antibacterial applications. Comparing freshly prepared nanochitins, neutral/alkaline stably dispersed nanochitins can be prepared while maintaining fibril characteristics such as fibril size, crystallinity, thermal stability and so on. Better suspension stability of modified nanochitins under alkaline conditon together with the self assembly performance resulting from amino groups and carboxyl groups benefit the enhanced emulsion stability under nanochitins concentreation of 0.2 %. Encapsulation of tea tree oil in Pickering Emulsions prolongs the diffusion rate oil in the aqueous environment, thus resulting prolongs its antibacterial performance against E. coli and B. subtilis.

Highly stretchable, tough and conductive chitin nanofiber composite hydrogel as a wearable sensor

To meet the requirements of eco-friendly and sustainability in the 21st century, hydrogels based on biopolymer with conductivity and stretchable property have attained increasing attention for strain sensor. However, the as-prepared of hydrogel sensor with excellent mechanical property and high strain sensitivity is still a challenge. In this study, chitin nanofiber (ChNF) reinforced composite hydrogels of PACF are fabricated via a facile one-pot method. The obtained PACF composite hydrogel exhibits good transparency (80.6 % at 800 nm)and excellent mechanical properties (tensile strength, 261.2 kPa; tensile strain as high as 550.3 %). Moreover, the composite hydrogels also demonstrate excellent anti-compression performance. The composite hydrogels own good conductivity (1.20 S/m) and strain sensitivity. Most importantly, the hydrogel can be assembled as a strain/pressure sensor for detecting large-scale and small-scale human motion. Therefore, flexible conductive hydrogel strain sensors will have broad application prospects in artificial intelligence, electronic skin, and personal health.

Nano-chitin: Preparation strategies and food biopolymer film reinforcement and applications

Current trends in food packaging systems are toward biodegradable polymer materials, especially the food biopolymer films made from polysaccharides and proteins, but they are limited by mechanical strength and barrier properties. Nano-chitin has great economic value as a highly efficient functional and reinforcing material. The combination of nano-chitin and food biopolymers offers good opportunities to prepare biodegradable packaging films with enhanced physicochemical and functional properties. This review aims to give the latest advances in nano-chitin preparation strategies and its uses in food biopolymer film reinforcement and applications. The first part systematically introduces various preparation methods for nano-chitin, including chitin nanofibers (ChNFs) and chitin nanocrystals (ChNCs). The nano-chitin reinforced biodegradable films based on food biopolymers, such as polysaccharides and proteins, are described in the second part. The last part provides an overview of the current applications of nano-chitin reinforced food biopolymer films in the food industry.

Extracellular Vesicle-Based Hydrogels for Wound Healing Applications

Hydrogels and extracellular vesicle-based therapies have been proposed as emerging therapeutic assets in wound closure. The combination of these elements has given good results in managing chronic and acute wounds. The intrinsic characteristics of the hydrogels in which the extracellular vesicles (EVs) are loaded allow for overcoming barriers, such as the sustained and controlled release of EVs and the maintenance of the pH for their conservation. In addition, EVs can be obtained from different sources and through several isolation methods. However, some barriers must be overcome to transfer this type of therapy to the clinic, for example, the production of hydrogels containing functional EVs and identifying long-term storage conditions for EVs. The aim of this review is to describe the reported EV-based hydrogel combinations, along with the obtained results, and analyze future perspectives.

Development of Stable Pickering Emulsions with TEMPO-Oxidized Chitin Nanocrystals for Encapsulation of Quercetin

Pickering emulsions stabilized by TEMPO-oxidized chitin nanocrystals (T-ChNCs) were developed for quercetin delivery. T-ChNCs were synthesized by TEMPO oxidation chitin and systematically characterized in terms of their physicochemical properties. T-ChNCs were rod-like with a length of 279.7 ± 11.5 nm and zeta potential around -56.1 ± 1.6 mV. The Pickering emulsions were analyzed through an optical microscope and CLSM. The results showed that the emulsion had a small droplet size (972.9 ± 86.0 to 1322.3 ± 447.7 nm), a high absolute zeta potential value (-48.2 ± 0.8 to -52.9 ± 1.9 mV) and a high encapsulation efficiency (quercetin: 79.6%). The emulsion stability was measured at different levels of T-ChNCs and pH values. The droplet size and zeta potential decreased with longer storage periods. The emulsions formed by T-ChNCs retarded the release of quercetin at half rate of that of the quercetin ethanol solution. These findings indicated that T-ChNCs are a promising candidate for effectively stabilizing Pickering emulsions and controlling release of quercetin.

Zwitterionic chitin nanocrystals mediated composite and self-assembly with cellulose nanofibrils

Zwitterionic dispersed chitin nanocrystals and TEMPO oxidized cellulose nanofibrils can be well mixed and self-assembled to be hydrogels/membranes. Active carboxyl groups ensure the well mixing of zwitterionic chitin nanocrystals and cellulose nanofibrils under neutral and alkaline condition. Electrostatic attraction between amino groups in chitin nanocrystals and carboxyl groups in chitin nanocrystals and cellulose nanofibrils further endows self-assemble property of composite suspensions. Simple standing for 12 h at room temperature is found enough for preparing self-assembled composite hydrogels. By 1-(3-dimethy-laminopropyl)-3-ethylcarbodiimide hydrochloride/N-hydroxy succinimide (EDC/NHS) mediated chemical crosslinking, the storage modulus of composite hydrogel can achieve almost 8 times higher than self-assembled hydrogel. Well dispersed composite suspensions also can be transformed to be membranes via filtration treatment. The strain increases almost 2.3 times higher with similar tensile strength for cellulose nanofibril rich samples, and chitin nanocrystals mainly contributes to the enhancement in strain of composite membranes.

Oxidized Chitin Nanocrystals Greatly Strengthen the Stability of Resveratrol-Loaded Gliadin Nanoparticles

Resveratrol (RES) is a natural polyphenol with a variety of health beneficial properties, but its application is greatly limited due to low aqueous solubility and poor bioavailability. This study aims to address these issues via gliadin nanoparticles stabilized with oxidized chitin nanocrystals (O-ChNCs) as a delivery system for RES. RES-loaded gliadin nanoparticles (GRNPs) were fabricated by an antisolvent method, and their formation mechanism was elucidated using zeta-potential, FTIR, XRD, and TEM. Furthermore, the effect of O-ChNCs on the colloidal stability and bioactiveness of GRNPs was discussed. The results demonstrate that O-ChNCs are adsorbed onto the surface of GRNPs through hydrogen bonding and electrostatic interactions, leading to the enhanced absolute potential and the improved hydrophobicity of the particles, which in turn facilitates the stability of the GRNPs. Furthermore, the changes in the release profile and antioxidant activity of RES in the simulated gastric and intestinal tracts indicate that the adsorption of O-ChNCs not only delays the release of RES but also has a protective effect on the antioxidant capacity of RES. This study provides significant implications for developing stable gliadin nanoparticles as delivery vehicles for bioactive substances.

Nanochitin: Chemistry, Structure, Assembly, and Applications

Chitin, a fascinating biopolymer found in living organisms, fulfills current demands of availability, sustainability, biocompatibility, biodegradability, functionality, and renewability. A feature of chitin is its ability to structure into hierarchical assemblies, spanning the nano- and macroscales, imparting toughness and resistance (chemical, biological, among others) to multicomponent materials as well as adding adaptability, tunability, and versatility. Retaining the inherent structural characteristics of chitin and its colloidal features in dispersed media has been central to its use, considering it as a building block for the construction of emerging materials. Top-down chitin designs have been reported and differentiate from the traditional molecular-level, bottom-up synthesis and assembly for material development. Such topics are the focus of this Review, which also covers the origins and biological characteristics of chitin and their influence on the morphological and physical-chemical properties. We discuss recent achievements in the isolation, deconstruction, and fractionation of chitin nanostructures of varying axial aspects (nanofibrils and nanorods) along with methods for their modification and assembly into functional materials. We highlight the role of nanochitin in its native architecture and as a component of materials subjected to multiscale interactions, leading to highly dynamic and functional structures. We introduce the most recent advances in the applications of nanochitin-derived materials and industrialization efforts, following green manufacturing principles. Finally, we offer a critical perspective about the adoption of nanochitin in the context of advanced, sustainable materials.

The effect of reduction on the properties of the regioselectively oxidized starch granules prepared by bromide-free oxidation system

Development of intact oxidized starch granules by regioselective oxidation technology is of interest and provides a new research direction for oxidized starch. In this study, new sodium tetrahydridoborate (NaBH₄)-treated oxidized starch (OS-BH₄) granules were prepared by a one-pot method, where native corn starch (NS) granules were oxidized by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)/sodium hypochlorite (NaClO) system followed by reduction with NaBH₄. Oxidized starch (OS) granules without NaBH₄ reduction were also prepared to investigate the effect of C6 aldehyde groups remained after TEMPO-mediated oxidation on properties of the granules. When degrees of oxidation were controlled to be not higher than 12%, both the OS and OS-BH₄ granules had similar morphology to the NS granules with envelopes. Compared to the OS granules, except for lower pasting temperatures and dextrose equivalents, the OS-BH₄ granules had higher molecular weights, degrees of polymerization (DP), peak viscosities, final viscosities, and swelling power. Difference of the properties was considered related to (1) repulsive forces formed between the C6 carboxylate groups, (2) C6 aldehyde groups with lower hydrophilicity than the C6 hydroxyl groups, and (3) some hemiacetal linkages formed between the C6 aldehyde groups and the hydroxyl groups. Furthermore, pregelatinized OS-BH₄ granules were preliminarily prepared, which showed good swelling behavior with intact granular morphology in alkaline environment.

Chitin Nanocrystals: Environmentally Friendly Materials for the Development of Bioactive Films

Biobased nanomaterials have gained growing interest in recent years for the sustainable development of composite films and coatings, providing new opportunities and high-performance products. In particular, chitin and cellulose nanocrystals offer an attractive combination of properties, including a rod shape, dispersibility, outstanding surface properties, and mechanical and barrier properties, which make these nanomaterials excellent candidates for sustainable reinforcing materials. Until now, most of the research has been focused on cellulose nanomaterials; however, in the last few years, chitin nanocrystals (ChNCs) have gained more interest, especially for biomedical applications. Due to their biological properties, such as high biocompatibility, biodegradability, and antibacterial and antioxidant properties, as well as their superior adhesive properties and promotion of cell proliferation, chitin nanocrystals have emerged as valuable components of composite biomaterials and bioactive materials. This review attempts to provide an overview of the use of chitin nanocrystals for the development of bioactive composite films in biomedical and packaging systems.

Deconstruction and Reassembly of Renewable Polymers and Biocolloids into Next Generation Structured Materials

This review considers the most recent developments in supramolecular and supraparticle structures obtained from natural, renewable biopolymers as well as their disassembly and reassembly into engineered materials. We introduce the main interactions that control bottom-up synthesis and top-down design at different length scales, highlighting the promise of natural biopolymers and associated building blocks. The latter have become main actors in the recent surge of the scientific and patent literature related to the subject. Such developments make prominent use of multicomponent and hierarchical polymeric assemblies and structures that contain polysaccharides (cellulose, chitin, and others), polyphenols (lignins, tannins), and proteins (soy, whey, silk, and other proteins). We offer a comprehensive discussion about the interactions that exist in their native architectures (including multicomponent and composite forms), the chemical modification of polysaccharides and their deconstruction into high axial aspect nanofibers and nanorods. We reflect on the availability and suitability of the latter types of building blocks to enable superstructures and colloidal associations. As far as processing, we describe the most relevant transitions, from the solution to the gel state and the routes that can be used to arrive to consolidated materials with prescribed properties. We highlight the implementation of supramolecular and superstructures in different technological fields that exploit the synergies exhibited by renewable polymers and biocolloids integrated in structured materials.

Biorenewable, transparent, and oxygen/moisture barrier nanocellulose/nanochitin-based coating on polypropylene for food packaging applications

Aluminum-coated polypropylene films are commonly used in food packaging because aluminum is a great gas barrier. However, recycling these films is not economically feasible. In addition, their end-of-life incineration generates harmful alumina-based particulate matter. In this study, coating layers with excellent gas-barrier properties are assembled on polypropylene films through layer-by-layer (LbL) deposition of biorenewable nanocellulose and nanochitin. The coating layers significantly reduce the transmission of oxygen and water vapors, two unfavorable gases for food packaging, through polypropylene films. The oxygen transmission rate of a 60 μm-thick, 20 LbL-coated polypropylene film decreases by approximately a hundredfold, from 1118 to 13.10 cc m^-2 day^-1 owing to the high crystallinity of nanocellulose and nanochitin. Its water vapor transmission rate slightly reduces from 2.43 to 2.13 g m^-2 day^-1. Furthermore, the coated film is highly transparent, unfavorable to bacterial adhesion and thermally recyclable, thus promising for advanced food packaging applications.

Liquid crystalline and rheological properties of chitin whiskers with different chemical structures and chargeability

The liquid crystalline and rheological properties of chitin whiskers (CHWs) are significant for their application in fabrication of highly ordered composite materials and optical components. The aim of this work was to elucidate the influence of chemical structure and chargeability (zeta potential, electropositivity, electronegativity or zwitterionic character) on the liquid crystalline and rheological properties of CHWs. Firstly, CHWs with different chemical structure, including positively charged whiskers (CHWs and CHWs-D/60 min) and negatively charged whiskers (mCHWs), were designed via acid hydrolysis, deacetylation, and maleation, respectively. Subsequently, the chargeability of the above whiskers was further regulated by protonation or deprotonation. The whisker aqueous suspensions with high zeta potential behaved as nematic liquid crystals or chiral nematic liquid crystals, whereas those with low zeta potential had no liquid crystal characteristics. The viscosity, G', and G" values of the CHWs and CHWs-D/60 min aqueous suspensions treated with protonation were lower than those of the corresponding whiskers treated with deprotonation. However, the mCHWs exhibited different changes in their rheological properties under protonation or deprotonation due to the electronegativity and zwitterionic characteristics. In addition, the effects of ionic strength and pH on the liquid crystalline and rheological properties of CHWs, CHWs-D/60 min, and mCHWs aqueous suspensions varied since the chemical structure and chargeability of whiskers differ.

Comparison of physicochemical and rheology properties of Shiitake stipes-derived chitin nanocrystals and nanofibers

Chitin production from fungal sources has gained increased attention in recent years in terms of continuous supply and safety. In this study, we produced chitin from Shiitake stipes through deproteinization, depigmentation, demineralization and removal of glucans, and then prepared chitin nanocrystal (ChNC) and chitin nanofibers (ChNF) by acid hydrolysis or high-pressure homogenizers. Such obtained ChNFs have higher length than the ChNCs with a length of 142.4 ± 40.4 nm, with the similar diameter (9 nm). In addition, the purity of ChNC and ChNF were over 98 % measured by HPAEC. The zeta potential analysis showed that ChNC is stable in acid form, while ChNF is in the opposite. Finally, we evaluated the rheology properties of samples to find the impact of salt concentrations on nanoparticles interactions. Overall, the fungi-derived chitin nanomaterials with diversity of characters exhibit immense potential for applications in nutraceutical and food industry.

Nanomaterials Derived from Fungal Sources-Is It the New Hype?

Greener alternatives to synthetic polymers are constantly being investigated and sought after. Chitin is a natural polysaccharide that gives structural support to crustacean shells, insect exoskeletons, and fungal cell walls. Like cellulose, chitin resides in nanosized structural elements that can be isolated as nanofibers and nanocrystals by various top-down approaches, targeted at disintegrating the native construct. Chitin has, however, been largely overshadowed by cellulose when discussing the materials aspects of the nanosized components. This Perspective presents a thorough overview of chitin-related materials research with an analytical focus on nanocomposites and nanopapers. The red line running through the text emphasizes the use of fungal chitin that represents several advantages over the more popular crustacean sources, particularly in terms of nanofiber isolation from the native matrix. In addition, many β-glucans are preserved in chitin upon its isolation from the fungal matrix, enabling new horizons for various engineering solutions.

Conductive biomass-based composite wires with cross-linked anionic nanocellulose and cationic nanochitin as scaffolds

In this study, a series of conductive composite wires were successfully prepared by combining dispersions of multi-wall carbon nanotubes (MWCNTs) and TEMPO-oxidized cellulose nanofibers (TOCNFs) with different MWCNTs contents into a dispersion of partially deacetylated α-chitin nanofibers (α-DECHNs) followed with a drying process. The TOCNFs/MWCNTs/α-DECHNs composite wires were prepared by extruding the negatively charged TOCNFs/MWCNTs dispersion into the positively charged α-DECHNs dispersion. The contact of the positively charged α-DECHNs and the negatively charged TOCNFs/MWCNTs triggers the electrostatic interaction (heterocoagulation) resulting in wire-shaped conductive composites. The SEM analysis indicates this conductive composite material has a wire-like shape with a rough but tight surface. The properties of samples were characterized by a zeta potential analyzer (Zetasizer Nano), a four-probe, an electrochemical workstation, a Fourier transform infrared spectroscopy (FTIR), an X-ray diffractometer (XRD), and a thermogravimetric analyzer (TG). Besides, the conductivity and the AC impedance of TOCNFs/MWCNTs/α-DECHNs composite wires with different MWCNTs contents were also analyzed. The conductivity of the composite wire increases from 9.98 × 10^-6 S∙cm^-1 to 1.56 × 10^-3 S∙cm^-1 as the MWCNTs content raises from 3.0 wt% to 14.0 wt%. When the MWCNTs content reaches 14.0 wt%, the prepared composite wire can light up LED at a voltage of 5 V, indicating the great potential of this biomass-based conductive composite in conductive material application.

Preparation of multifunctional carboxymethyl cellulose-based films incorporated with chitin nanocrystal and grapefruit seed extract

Chitin nanocrystals (ChNC) were isolated from shrimp shells powder using acid hydrolysis and ammonium persulfate methods. Multifunctional carboxymethyl cellulose (CMC) composite films were prepared by adding ChNC and grapefruit seed extract (GSE), and their effects on the optical, mechanical, water vapor barrier, and antibacterial properties of CMC film were investigated. The isolated ChNC had a needle-like structure with a length of 340-370 nm and a diameter of 18-20 nm depending on the isolation method. The CMC films prepared with ChNC and GSE were transparent with high UV barrier properties. The addition of GSE reduced the strength (TS) and stiffness (EM) of CMC films by 10.4% and 30.3%, respectively, while the flexibility (EB) increased by 17.7%. However, when the ChNC was added, the TS and EM of CMC film increased by 19.7% and 58.7%, respectively, and the EB remained the same. The addition of ChNC reduced the water vapor permeability (WVP) of the CMC film by 27%. CMC films containing GSE also showed strong antibacterial activity against foodborne pathogenic bacteria, E. coli and L. monocytogenes.

Biomaterials and controlled release strategy for epithelial wound healing

The skin and cornea are tissues that provide protective functions. Trauma and other environmental threats often cause injuries, infections and damage to these tissues, where the degree of injury is directly correlated to the recovery time. For example, a superficial skin or corneal wound may recover within days; however, more severe injuries can last up to several months and may leave scarring. Thus, therapeutic strategies have been introduced to enhance the wound healing efficiency and quality. Although the skin and cornea share similar anatomic structures and wound healing process, therapeutic agents and formulations for skin and cornea wound healing differ in accordance with the tissue and wound type. In this review, we describe the anatomy and epithelial wound healing processes of the skin and cornea, and summarize the therapeutic molecules that are beneficial to the respective regeneration process. In addition, biomaterial scaffolds that inherently possess bioactive properties or modified with therapeutic molecules for topical controlled release and enhanced wound healing efficiency are also discussed.

A simple mechanical agitation method to fabricate chitin nanogels directly from chitin solution and subsequent surface modification

Chitin nanogels (20–30 nm) with easy surface modification were prepared by high speed stirring of chitin solution in NaOH/urea solvent.

Preparation and Hydrogel Properties of pH-Sensitive Amphoteric Chitin Nanocrystals

Different from single charged or uncharged nanocrystals, amphoteric chitin nanocrystals (A-ChNCs) with both amine and carboxylate groups prepared with 2,2,6,6-tetramethylpiperidine-1-oxy-radical (TEMPO)-mediated oxidation and partial deacetylation were individually nanodispersed by sonicating in water at pH 3 and pH 11. The effects of the amount of NaClO₂ added in TEMPO-oxidation, deacetylation time, and sequence of the two treatments on the weight recovery ratios of the A-ChNCs were investigated. The A-ChNCs prepared under optimum conditions had an average length of ∼544 nm and an average width of ∼10 nm. The A-ChNCs nanodispersed in water at pH 3 and pH 11 had absolute ζ-potentials of >30 mV; however, in neutral water, they formed aggregations, which were nanodispersed again when pH was adjusted to 3 or 11, showing pH sensitivity. Hydrogels of A-ChNC were prepared by adding saturated NaCl solution and adsorbed both anionic and cationic dyes. Freeze-dried A-ChNC aerogels had three-dimensional network structures containing abundant pores.

Five different chitin nanomaterials from identical source with different advantageous functions and performances

Chitin is a renewable and sustainable biomass material that can be converted into various one-dimensional crystalline nanomaterials different in 1) length, 2) diameter, 3) charge density, 4) type of charge, and 5) crystallinity via diverse top-down synthetic methods. These nanomaterials have great potential as sustainable reinforcing and biologically functional materials. The proper design of chitin nanomaterials maximizes their performances in specific applications. Extensive efforts are devoted to understanding each type of chitin nanomaterial produced from different chitin sources; however, few studies have compared different chitin nanomaterials. Herein, we synthesize five different types of chitin nanomaterials from identical sources and compare their physical and chemical properties, including suitability for assorted purposes. Factors 1)-5) are discussed regarding their dominance in determining functionality depending on the specific goals of a) gas barriers, b) mechanical reinforcements, c) dispersibility in various pH aqueous buffers, d) thermal dimensional stability, and e) antibacterial activity. This study gives insights to design new chitin nanomaterial-based materials.

Biopolymer nanofibrils: structure, modeling, preparation, and applications

Biopolymer nanofibrils exhibit exceptional mechanical properties with a unique combination of strength and toughness, while also presenting biological functions that interact with the surrounding environment. These features of biopolymer nanofibrils profit from their hierarchical structures that spun angstrom to hundreds of nanometer scales. To maintain these unique structural features and to directly utilize these natural supramolecular assemblies, a variety of new methods have been developed to produce biopolymer nanofibrils. In particular, cellulose nanofibrils (CNFs), chitin nanofibrils (ChNFs), silk nanofibrils (SNFs) and collagen nanofibrils (CoNFs), as the four most abundant biopolymer nanofibrils on earth, have been the focus of research in recent years due to their renewable features, wide availability, low-cost, biocompatibility, and biodegradability. A series of top-down and bottom-up strategies have been accessed to exfoliate and regenerate these nanofibrils for versatile advanced applications. In this review, we first summarize the structures of biopolymer nanofibrils in nature and outline their related computational models with the aim of disclosing fundamental structure-property relationships in biological materials. Then, we discuss the underlying methods used for the preparation of CNFs, ChNFs, SNF and CoNFs, and discuss emerging applications for these biopolymer nanofibrils.