In-Vivo Assessment of Tissue Compatibility and Calcification of Bulk and Porous Silicon

Synthesis by solid route and physicochemical characterizations of blends of calcium orthophosphate powders and mesoporous silicon particles

The purpose of the study was to investigate the synthesis of economic calcium phosphate powders from recycled oyster shells, using a ball milling method. The oyster shell powder and a calcium pyrophosphate powder were used as starting materials and ball milled, then heat treated at 1,050°C for 5 h to produce calcium phosphate powders through a solid-state reaction. Electrochemically synthesized mesoporous silicon microparticles were then added to the prepared phosphate powders by mechanical mixer. The final powders were characterized using X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy to analyze their chemical composition and determine the most suitable process conditions. The biocompatibility of the produced powders was also tested in vitro using murine cells and the results showed good biocompatibility.

Nanoplatforms for Irinotecan Delivery Based on Mesoporous Silica Modified with a Natural Polysaccharide

Natural compounds are an important source of beneficial components that could be used in cancer therapy along with well-known cytostatic agents to enhance the therapeutic effect while targeting tumoral tissues. Therefore, nanoplatforms containing mesoporous silica and a natural polysaccharide, ulvan, extracted from Ulva Lactuca seaweed, were developed for irinotecan. Either mesoporous silica-ulvan nanoplatforms or irinotecan-loaded materials were structurally and morphologically characterized. In vitro drug release experiments in phosphate buffer solution with a pH of 7.6 emphasized the complete recovery of irinotecan in 8 h. Slower kinetics were obtained for the nanoplatforms with a higher amount of natural polysaccharide. Ulvan extract proved to be biocompatible up to 2 mg/mL on fibroblasts L929 cell line. The irinotecan-loaded nanoplatforms exhibited better anticancer activity than that of the drug alone on human colorectal adenocarcinoma cells (HT-29), reducing their viability to 60% after 24 h. Moreover, the cell cycle analysis proved that the irinotecan loading onto developed nanoplatforms caused an increase in the cell number trapped at G0/G1 phase and influenced the development of the tumoral cells.

Controlling and Predicting the Dissolution Kinetics of Thermally Oxidised Mesoporous Silicon Particles: Towards Improved Drug Delivery

Porous silicon (pSi) continues to receive considerable interest for use in applications ranging from sensors, biological scaffolds, therapeutic delivery systems to theranostics. Critical to all of these applications is pSi degradation and stabilization in biological media. Here we report on progress towards the development of a mechanistic understanding for the dissolution behavior of native (unoxidized) and thermally oxidized (200-600 °C) pSi microparticles. Fourier transform infrared (FTIR) spectroscopy was used to characterize the pSi surface chemistry after thermal oxidation. PSi dissolution was assessed using a USP method II apparatus by monitoring the production of orthosilicic acid, and the influence of gastro-intestinal (GI) fluids were examined. Fitting pSi dissolution kinetics with a sum of the exponential model demonstrated that the dissolution process strongly correlates with the three surface hydride species and their relative reactivity, and was supported by the observed FTIR spectral changes of pSi during dissolution. Finally, the presence of GI proteins was shown to hamper pSi dissolution by adsorption to the pSi surface acting as a barrier preventing water attack. These findings are significant in the optimal design of pSi particles for oral delivery and other controlled drug delivery applications.

Harnessing the Aqueous Chemistry of Silicon: Self-Assembling Porous Silicon/Silica Microribbons

The synthesis of microribbons based on the assembly of porous silicon nanoparticles (pSiNPs) in a silica matrix is reported. The formation of these structures is driven by dissolution and reprecipitation of silica derived from the NPs upon drying of an aqueous colloidal dispersion. The process generates composite films that fracture into filaments due to geometric stresses associated with drying of the film on a curved surface. By controlling NP concentration, solvent, and temperature during the evaporation process, well-defined microribbons with a rectangular cross section of ∼25 × 100 microns and lengths on the order of 1 cm are formed. Partial thermal oxidation of the ribbons generates luminescent Si-SiO₂ core-shell composites, and complete oxidation generates porous SiO₂ ribbons with retention of the mesoporous nanostructure. The pores can be infiltrated with daunorubicin as a model drug, and the resulting material shows sustained release of the chemotherapeutic for more than 70 days.

Multimodality Imaging of Silica and Silicon Materials In Vivo

Recent progress in the development of silica- and silicon-based multimodality imaging nanoprobes has advanced their use in image-guided drug delivery, and the development of novel systems for nanotheranostic and diagnostic applications. As biocompatible and flexibly tunable materials, silica and silicon provide excellent platforms with high clinical potential in nanotheranostic and diagnostic probes with well-defined morphology and surface chemistry, yielding multifunctional properties. In vivo imaging is of great value in the exploration of methods for improving site-specific nanotherapeutic delivery by silica- and silicon-based drug-delivery systems. Multimodality approaches are essential for understanding the biological interactions of nanotherapeutics in the physiological environment in vivo. The aim here is to describe recent advances in the development of in vivo imaging tools based on nanostructured silica and silicon, and their applications in single and multimodality imaging.

Thermally Carbonized Porous Silicon and Its Recent Applications

Recent progress in research on thermally carbonized porous silicon (TCPSi) and its applications is reported. Despite a slow start, thermal carbonization has now started to gain interest mainly due to new emerging areas for applications. These new areas, such as optical sensing, drug delivery, and energy storage, require stable surface chemistry and physical properties. TCPSi is known to have all of these desired properties. Herein, the above-listed properties of TCPSi are summarized, and the carbonization processes, functionalization, and characterization of TCPSi are reviewed. Moreover, some of the emerging fields of TCPSi applications are discussed and recent advances in the fields are introduced.

Oral Mucosal Epithelial Cells Grown on Porous Silicon Membrane for Transfer to the Rat Eye

Dysfunction of limbal stem cells or their niche can result in painful, potentially sight-threatening ocular surface disease. We examined the utility of surface-modified porous-silicon (pSi) membranes as a scaffold for the transfer of oral mucosal cells to the eye. Male-origin rat oral mucosal epithelial cells were grown on pSi coated with collagen-IV and vitronectin, and characterised by immunocytochemistry. Scaffolds bearing cells were implanted into normal female rats, close to the limbus, for 8 weeks. Histology, immunohistochemistry and a multiplex nested PCR for sry were performed to detect transplanted cells. Oral mucosal epithelial cells expanded on pSi scaffolds expressed the corneal epithelial cell marker CK3/12. A large percentage of cells were p63+, indicative of proliferative potential, and a small proportion expressed ABCG2+, a putative stem cell marker. Cell-bearing scaffolds transferred to the eyes of live rats, were well tolerated, as assessed by endpoint histology. Immunohistochemistry for pan-cytokeratins demonstrated that transplanted epithelial cells were retained on the pSi membranes at 8 weeks post-implant, but were not detectable on the central cornea using PCR for sry. The pSi scaffolds supported and retained transplanted rat oral mucosal epithelial cells in vitro and in vivo and recapitulate some aspects of an artificial stem cell niche.

In Vitro Gene Delivery with Large Porous Silicon Nanoparticles Fabricated Using Cost-Effective, Metal-Assisted Chemical Etching

The cytocompatibility, cell membrane affinity, and plasmid DNA delivery from surface oxidized, metal-assisted stain-etched mesoporous silicon nanoscale particles (pSiNPs) to human embryonic kidney (HEK293) cells is demonstrated, suggesting the possibility of using such material for targeted transfection and drug delivery.

Novel delivery systems for improving the clinical use of peptides

Peptides have long been recognized as a promising group of therapeutic substances to treat various diseases. Delivery systems for peptides have been under development since the discovery of insulin for the treatment of diabetes. The challenge of using peptides as drugs arises from their poor bioavailability resulting from the low permeability of biological membranes and their instability. Currently, subcutaneous injection is clinically the most common administration route for peptides. This route is cost-effective and suitable for self-administration, and the development of appropriate dosing equipment has made performing the repeated injections relatively easy; however, only few clinical subcutaneous peptide delivery systems provide sustained peptide release. As a result, frequent injections are needed, which may cause discomfort and additional risks resulting from a poor administration technique. Controlled peptide delivery systems, able to provide required therapeutic plasma concentrations over an extended period, are needed to increase peptide safety and patient compliancy. In this review, we summarize the current peptidergic drugs, future developments, and parenteral peptide delivery systems. Special emphasis is given to porous silicon, a novel material in peptide delivery. Biodegradable and biocompatible porous silicon possesses some unique properties, such as the ability to carry exceptional high peptide payloads and to modify peptide release extensively. We have successfully developed porous silicon as a carrier material for improved parenteral peptide delivery. Nanotechnology, with its different delivery systems, will enable better use of peptides in several therapeutic applications in the near future.

Influence of Surface Chemistry on the Release of an Antibacterial Drug from Nanostructured Porous Silicon

Nanostructured mesoporous silicon possesses important properties advantageous to drug loading and delivery. For controlled release of the antibacterial drug triclosan, and its associated activity versus Staphylococcus aureus, previous studies investigated the influence of porosity of the silicon matrix. In this work, we focus on the complementary issue of the influence of surface chemistry on such properties, with particular regard to drug loading and release kinetics that can be ideally adjusted by surface modification. Comparison between drug release from as-anodized, hydride-terminated hydrophobic porous silicon and the oxidized hydrophilic counterpart is complicated due to the rapid bioresorption of the former; hence, a hydrophobic interface with long-term biostability is desired, such as can be provided by a relatively long chain octyl moiety. To minimize possible thermal degradation of the surfaces or drug activity during loading of molten drug species, a solution loading method has been investigated. Such studies demonstrate that the ability of porous silicon to act as an effective carrier for sustained delivery of antibacterial agents can be sensitively altered by surface functionalization.

The role of nanostructured mesoporous silicon in discriminating in vitro calcification for electrospun composite tissue engineering scaffolds

The impact of mesoporous silicon (PSi) particles-embedded either on the surface, or totally encapsulated within electrospun poly (ε-caprolactone) (PCL) fibers-on its properties as a tissue engineering scaffold is assessed. Our findings suggest that the resorbable porous silicon component can sensitively accelerate the necessary calcification process in such composites. Calcium phosphate deposition on the scaffolds was measured via in vitro calcification assays both at acellular and cellular levels. Extensive attachment of fibroblasts, human adult mesenchymal stem cells, and mouse stromal cells to the scaffold were observed. Complementary cell differentiation assays and ultrastructural measurements were also carried out; the levels of alkaline phosphatase expression, a specific biomarker for mesenchymal stem cell differentiation, show that the scaffolds have the ability to mediate such processes, and that the location of the Si plays a key role in levels of expression.

Cell culture on MEMS platforms: a review

Microfabricated systems provide an excellent platform for the culture of cells, and are an extremely useful tool for the investigation of cellular responses to various stimuli. Advantages offered over traditional methods include cost-effectiveness, controllability, low volume, high resolution, and sensitivity. Both biocompatible and bio-incompatible materials have been developed for use in these applications. Biocompatible materials such as PMMA or PLGA can be used directly for cell culture. However, for bio-incompatible materials such as silicon or PDMS, additional steps need to be taken to render these materials more suitable for cell adhesion and maintenance. This review describes multiple surface modification strategies to improve the biocompatibility of MEMS materials. Basic concepts of cell-biomaterial interactions, such as protein adsorption and cell adhesion are covered. Finally, the applications of these MEMS materials in Tissue Engineering are presented.

Mesoporous silicon in drug delivery applications

During the last few years, a number of interesting drug delivery applications of mesoporous materials have been demonstrated. Mesoporous silicon has many important properties advantageous to drug delivery applications. The small size of the pores confines the space of a drug and engages the effects of surface interactions of the drug molecules and the pore wall. The size of the pores and the surface chemistry of the pore walls may be easily changed and controlled. Depending on the size and the surface chemistry of the pores, increased or sustained release of the loaded drug can be obtained. Drug loading from a solution at room temperature enables the use of porous silicon (PSi) also with sensitive therapeutic compounds susceptible to degradation, like peptides and proteins. This article reviews the fabrication and chemical modifications of PSi for biomedical applications, and also the potential advantages of PSi in drug delivery.

Accelerated calcification in electrically conductive polymer composites comprised of poly(ɛ-caprolactone), polyaniline, and bioactive mesoporous silicon

In this study the fabrication and characterization of an electrically conductive composite material comprised of poly(epsilon-caprolactone) (PCL), polyaniline (PANi), and bioactive mesoporous silicon (BioSilicon) is discussed. The influence of PANi and silicon on calcium phosphate induction was assessed via ex vitro calcification analyses (by acellular simulated body fluid (SBF) exposure) both with and without electrical bias. Acceleration of calcium phosphate formation is one possible desirable feature of "smart" synthetic scaffolds for selected orthopedic-relevant applications. In addition, electrical stability assays were performed in growth medium (DMEM) to determine the stability of such structures to bias in an authentic electrolyte during a typical cell experiment. The cytocompatibility of the composites was evaluated in vitro using human kidney fibroblasts (HEK 293) cell proliferation assays, along with more orthopedically relevant mesenchymal stem cells from mouse stroma. Importantly, these composites demonstrate accelerated calcification in SBF when electrical bias is applied cathodically to the scaffold. Furthermore, these scaffolds exhibit noncytotoxic behavior in the presence of fibroblasts over an 8-day culture period, and attachment of stromal cells to the semiconducting scaffold was directly imaged via scanning electron microscopy. Overall, these results suggest that materials of this type of composition have potential merit as a biomaterial.

Biorelevant mesoporous silicon / polymer composites: directed assembly, disassembly, and controlled release

We describe in this account a general, yet facile strategy for the directed assembly of bioactive composite materials comprised of an erodible organic polymer such as polycaprolactone and physiologically-resorbable inorganic mesoporous silicon. This method exploits a combination of capillary forces and selective interfacial coupling chemistry to produce isolable macroscale (mm sized) structures possessing a diverse range of geometries through simple mixing rather than intricate molding processes. Furthermore, we demonstrate the ability of such constructs to dissociate into their individual building blocks, with the concomitant release of embedded model compounds in a sustained manner.

Penetration and loading of human serum albumin in porous silicon layers with different pore sizes and thicknesses

Human serum albumin was adsorbed into porous silicon layers with thickness up to 3 microm and with different mean pore radius in the range 4.5-10 nm. The adsorbed amount of protein was quantified by I(125) radioactive labeling techniques and ellipsometry. The results show that albumin penetrated into the pores when the mean pore radius was larger than 5.5 nm, but could not totally occupy the available surface area when the layer thickness was larger than 1 microm. Loading of albumin both into porous layers and onto plane silicon as a function of albumin concentration was also investigated. These measurements show that loading of protein increased with protein concentration at least up to 10 mg/ml for porous silicon and up to 1 mg/ml for plane silicon. The maximum deposition into the type of porous layers used here was 28 microg/cm(2), compared to 0.36 microg/cm(2) for plane silicon.