Optical and Surface Properties of Monolithic Zirconia after Simulated Toothbrushing

Color and surface stainability of additively and subtractively manufactured interim restorative materials against mouth rinses

STATEMENT OF PROBLEM

Interim restorations are often used along with mouth rinses during the healing period following surgical procedures. However, evidence regarding the color and surface properties of digitally fabricated interim restorations after oral rinsing is lacking.

PURPOSE

The purpose of this in vitro study was to evaluate whether different mouth rinses could affect the color and surface roughness of milled and printed interim restorations after simulated oral rinsing.

MATERIAL AND METHODS

Disk-shaped specimens (Ø15×2 mm; N=180) were fabricated by using conventional (Jet Tooth Shade), milled (Yamahachi PMMA Disk), and printed (NextDent C&B) resin materials. All resin specimens were divided into 3 different groups according to the rinsing material: distilled water, whitening mouth rinse (Listerine Healthy White), and conventional mouth rinse (Listerine Cool Mint). The specimens were further allocated into short- and long-term subgroups, and oral rinsing simulation was performed (n=10). Short-term rinsing simulated the conditions in a usual interim restoration period, and long-term rinsing was performed to evaluate the properties of the interim materials. The color differences (CIEDE2000, ΔE00) between the baseline and each time point were determined by using a spectrophotometer. The surface roughness of the tested specimens was measured by using a confocal laser scanning microscope. Kruskal-Wallis and Friedman tests with nonparametric pairwise comparisons were used to analyze the data (α=.05).

RESULTS

On simulation of a 6-month use of the mouth rinse, the color change in the milled resin did not differ from that in the conventional resin (P>.334), but the printed resin showed a significantly greater color change than the other resins (P<.007). The greatest color change with the printed resin was observed when a conventional mouth rinse was used. However, all color changes were below a perceptible threshold of 1.30. When daily rinsing for 14 years was simulated, all resin groups showed a perceptible color change when conventional mouth rinse was used, and the printed resin showed the greatest median ±interquartile range ΔE00 (2.24 ±0.2). In both short- and long-term simulations, the printed resin rinsed with the conventional mouth rinse showed significantly greater roughness than that rinsed with distilled water (P<.009).

CONCLUSIONS

The printed resin showed higher stainability than the conventional resin, and the color change was greatest with the conventional mouth rinse. However, in 6 months of daily mouth rinse simulation, all the tested resin materials exhibited imperceptible color change and clinically acceptable surface roughness.

A Study on the Biofilm Removal Efficacy of a Bioelectric Toothbrush

Effective oral care is a critical requirement to maintain a high quality of life. Most oral diseases are caused by plaque (oral biofilm), which is also correlated with systemic diseases. A common method to remove biofilm is brushing teeth with toothpaste. However, 3.5 billion people in the world have oral diseases, meaning that more efficient methods of removing biofilms are needed. We have developed a toothbrush that applies a bioelectric effect (BE) utilizing an electric force for biofilm removal. It demonstrated significantly higher biofilm removal efficiency than non-BE manual toothbrushes. Tests were performed in saline and toothpaste conditions using various pressures. Results showed that the BE toothbrush had a significantly higher biofilm removal efficiency in saline (0.5 N: 215.43 ± 89.92%, 2.5 N: 116.77 ± 47.02%) and in a toothpaste slurry (0.5 N: 104.96 ± 98.93%, 2.5 N: 96.23 ± 35.16%) than non-BE manual toothbrushes. Results also showed that BE toothbrushes were less dependent on toothpaste. This study suggests that the application of BE can be a new solution to plaque problems in oral care.

Biomimetic Whitening Effect of Polyphosphate-Bleaching Agents on Dental Enamel

This in vitro study investigated the extrinsic tooth-whitening effect of bleaching products containing polyphosphates on the dental enamel surface compared to 10% carbamide peroxide (CP). Eighty human molars were randomly allocated into four whitening-products groups. Group A (control) was treated with 10% CP (Opalescence). The other groups with non-CP over-the-counter (OTC) products were group B = polyphosphates (iWhiteWhitening-Kit); group C = polyphosphates+fluoride (iWhite-toothpaste); and group D = sodium bicarbonate (24K-Whitening-Pen). L*, a*, b* color-parameters were spectrophotometer-recorded at baseline (T0), one day (T1), and one month (T2) post-treatment. Changes in teeth color (ΔEab) were calculated. Data were analyzed using ANOVA and the Bonferroni test (α = 0.05). Groups A, B, and D showed significant differences in ΔL*&Δa* parameters at T1, but not in Δb* at T0. Group C showed no difference for ΔL*, Δa*, Δb* at T0 and T1. Group A showed differences for ΔL*, Δa*, Δb*, at T2, while groups B, C, and D had no difference in any parameters at T0. At T1, ΔEab values = A > D> B > C (ΔEab = 13.4 > 2.4 > 2.1 > 1.2). At T2, ΔEab values increased = A > B > C > D (ΔEab = 12.2 > 10.6 > 9.2 > 2.4). In conclusion, the 10% CP and Biomimetic polyphosphate extrinsic whitening kit demonstrated the highest color change, while simulated brushing with dark stain toothpaste and a whitening pen demonstrated the lowest color change at both measurement intervals.

Shear Bond Strength of Two Repair Systems to Zirconia Ceramic by Different Surface Treatments

Introduction: Intraoral repair has been suggested as a treatment option to repair the chipping or fracture of veneered zirconia; the success of the procedure is mainly determined by the bonding between zirconia and composite resin. The present study aimed to investigate and compare the shear bond strength (SBS) of two intraoral repair systems to zirconia ceramic treated with a laser or air-abrasion surface modification. Methods: Ninety tube-shaped samples (diameter of 10 mm and height of 4 mm) were divided into three main groups: Group I (zirconia 100%, n=30); Group II (veneer ceramic 100% n=30); Group III (zirconia with a veneer ceramic n=30). Each main group was subdivided into two subgroups (n=15): Subgroup A: samples repaired with Ceramic Repair N; Subgroup B: samples repaired with the Cimara Repair System. The subgroup samples were further subdivided based on the treated surface (n=5 samples): Control (no surface modification), Er,Cr:YSGG laser surface modification, and air-abrasion surface modification. The SBS was employed using a universal testing machine. The mode of failure was observed using a stereomicroscope. Results: Significant differences were observed in the mean SBS values between the different surface modifications (P˂0.05). Tukey's post hoc test showed that the air-abrasion surface modification of the veneer ceramic repaired with the Ceramic repair N system had the highest mean value (13.74 MPa) among the different groups, while no surface modification of zirconia repaired with the Cimara repair system had the lowest mean value (2.84 MPa). The control group (no surface modification) had the lowest mean value among all the treated groups. Conclusion: The SBS is surface modification-dependent, and higher SBS is obtained by air-abrasion than Er, Cr:YSGG laser surface modifications with the selected parameters. The Ceramic repair N system had significantly higher SBS for all surface-treated substrates than the Cimara repair system.

Effect of Over-The-Counter Tooth-Whitening Products on Enamel Surface Roughness and Microhardness

Background: To evaluate the efficacy of new over-the-counter tooth-whitening products on enamel surface roughness and microhardness. Methods: A total of 120 enamel specimens were prepared and randomly allocated into six groups. Group A was treated with 10% carbamide peroxide; Group B was immersed in distilled water; Group C was treated with hydrated silica, sodium hexametaphosphate toothpaste; Group D was treated with sodium bicarbonate; Group E was treated with 0.25% citric acid; and Group F was treated with hydrated silica, charcoal powder. Results: A, B, and D demonstrated decreased Ra, whereas Groups C, E, and F showed an increased Ra after whitening. The changes in Ra from T0 to T1 in each group was statistically significant (p < 0.001) except for Group B (p = 0.85). The groups showed decreased KHN after whitening, except for specimens in Group B (distilled water). The KHN from T0 to T1 decreased significantly for groups A, C, E, and F (p = 0.001). Significant difference was observed at T1 (p < 0.0001). Conclusion: Within the limitations of this study, it could be demonstrated that surface roughness and enamel microhardness changes were influenced by the type, composition, and exposure time of the whitening product.

In vitro effect of resin infiltrant on resistance of sound enamel surfaces in permanent teeth to demineralization

OBJECTIVE

To investigate the effect of resin infiltrant on resistance of sound permanent enamel surfaces to demineralization.

METHOD

Eighty healthy premolars were sectioned to obtain enamel blocks from the buccal surface. Specimens with baseline surface microhardness values of 320-370 were selected. The experimental group were treated with resin infiltrant, while the control group was not. Specimens from each group were artificially demineralized and the surface microhardness values were measured again. Confocal laser scanning microscopy was used to measure the depth of demineralization and detect the penetration ability of the resin infiltrant. The specimens were subjected to a simulated toothbrushing abrasion test. Scanning electron microscopy was used to observe changes in the surface morphology of specimens after each of these procedures.

RESULTS

No significant differences between the experimental and control groups were observed in the baseline microhardness values or in the experimental group after resin infiltration compared with the baseline conditions. After artificial demineralization, the microhardness value in the control group was significantly lower than that in the experimental group (266.0 (±34.5) compared with 304.0 (±13.0), P = 0.017). Confocal laser scanning microscopy results showed that the demineralization depth in the control group was significantly deeper than that in the experimental group (97.9 (±22.8) µm vs. 50.4 (±14.3) µm, P < 0.001), and that resin infiltrant completely penetrated the acid-etched demineralized area of the tooth enamel with a mean penetration depth of 31.6 (±9.0) µm. Scanning electron microscopy showed that the surface morphology was more uniform and smoother after simulated toothbrushing. The enamel surface structure was more severely destroyed in the control group after artificial demineralization compared with that of the experimental group.

CONCLUSION

Resin infiltrant can completely penetrate an acid-etched demineralized enamel area and improve resistance of sound enamel surfaces to demineralization. Our findings provide an experimental basis for preventive application of resin infiltrant to sound enamel surfaces to protect tooth enamel against demineralization.

Assessment of Knowledge, Attitude, and Practice of Iranian Nurses towards Toothbrush Maintenance and Use

Background

Since nurses are considered a role model in society, they should have sufficient knowledge, attitude, and practice in the field of oral hygiene. This study was aimed to assess the nurses' knowledge, practice, and attitude towards toothbrush maintenance and use.

Methods

In this cross-sectional study, 325 nurses working in hospitals affiliated to Kermanshah University of Medical Sciences were randomly recruited. Data collection tools included a demographic information form and a researcher-made questionnaire on knowledge, attitude, and practice regarding toothbrush maintenance and use. Data were analyzed by SPSS software using descriptive and inferential statistics (Mann–Whitney U and Kruskal–Wallis H).

Results

The mean scores of nurses' knowledge, attitude, and practice were 59.2 ± 16.4, 64.2 ± 20.6, and 51.4 ± 17.0 out of 100, respectively. There was no statistically significant relation between nurses' knowledge, attitude, and practice and their gender, age, level of education, and work experience.

Conclusions

Nurses had moderate knowledge, attitude, and practice regarding toothbrush maintenance and use, which is not very desirable given their role model. Therefore, training courses are recommended to be held to increase the nurses' knowledge, attitude, and practice regarding toothbrush maintenance and use.

Effect of toothbrushing on the optical properties and surface roughness of extrinsically stained high-translucency zirconia

OBJECTIVES

The effect of toothbrushing on the color, relative translucency, and surface roughness of extrinsically stained zirconia dental restorations is still unclear. The purpose of the present study was to evaluate the optical properties and surface textures of extrinsically stained or glazed partially stabilized zirconia with 5 mol% yttria (5Y-PSZ) after toothbrushing by determining changes in the color, translucency parameter (TP), and surface roughness.

MATERIALS AND METHODS

Specimens (2 mm thick; n = 50) were sectioned from 5Y-PSZ blanks. Three brands of powdered stains (namely VI, SH, IV) and a glaze (GL) were used to extrinsically stain the specimen surfaces (n = 10 per group). The specimens were subjected to 10,000-50,000 simulated toothbrushing strokes using a toothpaste slurry (Ora2 PREMIUM Stain clear paste). The color parameters were measured before staining or glazing and before and after simulated brushing. The color changes and TP values can be calculated before and after simulated brushing. The surface roughness was also evaluated.

RESULTS

Significant changes were found in the shade and TP values of 5Y-PSZ after extrinsic staining, but no significant changes were found after toothbrushing, irrespective of the staining brand (p > 0.05). The surface roughness of the characterized 5Y-PSZ specimens decreased after toothbrushing, whereas that of the non-characterized 5Y-PSZ group increased.

CONCLUSIONS

Toothbrushing markedly affects the surface roughness of extrinsically stained or glazed 5Y-PSZ specimens, whereas no impacts on the color or translucency were observed.

CLINICAL RELEVANCE

For esthetic reasons, clinicians and dental technicians prefer to apply extrinsic stains to zirconia restorations, which profoundly affects its appearance. The limited influence of toothbrushing on color and translucency of 5Y-PSZ is promising for clinical applications.

The Effects of a coffee beverage and whitening systems on surface roughness and gloss of CAD/CAM lithium disilicate glass ceramics

OBJECTIVES

To investigate the effects of a coffee beverage and two whitening systems on the surface roughness and gloss of glazed Lithium Disilicate Glass-Ceramics (LDGC) for computer-aided design/computer-aided manufacturing (CAD/CAM) systems.

METHODS

Sixty-eight LDGC disks (12 × 10 × 2 mm) were prepared from blocks of CAD/CAM systems (IPS e.max CAD ceramic). Baseline measurements for surface roughness (Ra) and gloss (GU) were taken using a 3-D optical profilometer and a glossmeter, respectively; then specimens were randomized into four groups (n = 17). All specimens were immersed in a coffee solution (24 h × 12 days) then subjected to two whitening systems. G1-negative control (kept moist × 7 days); G2-positive control (brushed with distilled water, 200 g/load, 2 min twice daily × 7 days); G3-whitening toothpaste (Colgate optic white; relative dentin abrasivity (RDA) = 100, 200 g/load, 2 min twice daily × 7 days); and G4-simulated at-home bleaching protocol (Opalescence,15% carbamide peroxide (CP), 6 h/day × 7 days). The study outcomes were measured at baseline and after the treatments. Data were analyzed using paired T-test and one-way ANOVA (α = 0.05).

RESULTS

The mean surface roughness significantly increased (p ⩽ 0.002) for all groups after the designated treatment protocols. Among groups, the mean surface roughness of G2 and G3 were significantly higher (p ⩽ 0.001) (Ra: 0.51 and 0.57 μm, respectively) compared to the control group (Ra: 0.23 μm), and were not significantly different from G4 (Ra: 0.46 μm). Surface gloss decreased with no significant change within or among groups after treatment.

CONCLUSION

All glazed LDGC had a significant increase in surface roughness after being subjected to simulated 1 year of coffee drinking and whitening systems (15% CP and whitening toothpaste), and the greatest change was associated with brushing (simulating 8 months). However, coffee beverages and whitening systems had no significant effect on the surface gloss.

Surface roughness and color measurements of glazed or polished hybrid, feldspathic, and Zirconia CAD/CAM restorative materials after hot and cold coffee immersion

Background

The purpose of this study evaluates and compares the effect of surface roughness (Ra) and color stability on computer-aided design/computer-aided manufacturing (CAD/CAM) hybrid resin (Vita Enamic), feldspathic (Vitablocs® Mark II), and lithium disilicate Zirconia (Vita Suprinity) glazed or polished ceramics immersed in hot Arabic Qahwa and cold coffee.

Methods

A total of 96 standardized samples were prepared from CAD/CAM restorative materials. Half of the samples were polished as per the manufacturer’s instructions using a porcelain polishing kit, and the other half were glazed. Samples were distributed and immersed in hot Arabian Qahwa and cold coffee followed by thermocycling. Ra measurements and color changes were conducted before and after immersion. SEM images were captured from each type of glazed or polished ceramic. One-way ANOVA paired Student’s t-test, and Bonferroni test were conducted to detect significant difference between the groups. P > 0.05 was a significant level.

Results

Of all the tested samples, Ra increased without any significant difference; however, mean color changes (ΔE*) showed significant differences. An increase in Ra was noted for all the glazed and polished samples after immersion and thermocycling. However, differences were significant only in VM II. In addition, ΔE* was significant only in Vita Suprinity (VS) samples. For immersion groups, significant Ra changes were noticed in glazed samples, only in Vita Enamic (VE) with no ΔE*. In polished samples, mean Ra changes were observed in VM II and VS samples. Significant differences were also noticed in polished VE and VS subgroups of ΔE*.

Conclusions

Ra affects all the tested samples, providing higher values on the polished specimens. The ΔE* caused by hot Arabic Qahwa and cold coffee on glazed or polished CAD/CAM restorative materials were clinically acceptable.

Finite Element Analysis of Dental Implants with Zirconia Crown Restorations: Conventional Cement-Retained vs. Cementless Screw-Retained

The present study was designed to compare the stress distributions in two restoration types of implants and the surrounding bone. The first restoration type was a conventional cement-retained zirconia crown, and the second was a novel cementless screw-retained zirconia crown with a base abutment. A three-dimensional finite element method was used to model the implants, restorations, and supporting bone. A comparative study of the two implants was performed under two masticatory loads: a vertical load of 100 N and a 30-degree oblique load of 100 N. Under both loading conditions, the maximum von Mises stress and strain values in the implant and supporting bone were higher in the conventional cement-retained restoration model than in the cementless screw-retained model. In terms of stress distribution, the cementless screw-retained zirconia crown with base abutment may be considered a superior restoration option compared to the conventional cement-retained zirconia crown.

Effects of Khat on Surface Roughness and Color of Feldspathic and Zirconia Porcelain Materials under Simulated Oral Cavity Conditions

Background and Objectives: Khat chewing is considered as a daily habit that is practiced by more than five million people globally. The effect of khat chewing on the surface roughness and the color stability of natural teeth and the material used in the fabrication of dental prosthesis remains unknown. This study was conducted to explore and compare the effect of khat homogenate (KH) on the surface roughness (Ra) and the average color changes (ΔE*) amongst natural teeth and selected shades from different porcelain types, namely, feldspathic metal ceramic (MC) VM13, computer-aided design/computer assisted manufacture (CAD/CAM) feldspathic (Vitablocs Mark II), and multilayer zirconia (Ceramill Zolid PS) porcelains. Materials and Methods: Seventy samples were prepared from natural teeth, feldspathic MC, CAD/CAM Vitablocs Mark II, and zirconia porcelain. The Ra values were measured using a profilometer and expressed in micrometers, whereas the ΔE* values were measured using VITA Easyshade^® V spectrophotometer for all samples before and after frequent immersion and thermocycling in KH for 30 days. The surface topography was used to assess the materials surfaces (glazed or polished) after KH immersion by using a white light interferometry machine. Results: Results revealed that the Ra and the ΔE* values of the different types of tested porcelain were influenced by KH. The order of surface roughness values was glazed or polished MC > polished Zircon > polished Vitablocs Mark II > natural teeth. The lowest ΔE* values were recorded for glazed Vitablocs Mark II and MC, and the values could be arranged as polished zircon > natural teeth > glazed zircon > polished MC > polished Vitablocs Mark II. P values were significantly varied (<0.001) among all the tested groups, except the zircon group (>0.05) for both Ra and ΔE*. Conclusions: KH significantly affected both surface parameter and color of glazed or polished porcelain materials and natural teeth.

Monolithic Zirconia: An Update to Current Knowledge. Optical Properties, Wear, and Clinical Performance

The purpose of this paper was to update the knowledge concerning the wear, translucency, as well as clinical performance of monolithic zirconia ceramics, aiming at highlighting their advantages and weaknesses through data presented in recent literature. New ultra-translucent and multicolor monolithic zirconia ceramics present considerably improved aesthetics and translucency, which, according to the literature reviewed, is similar to those of the more translucent lithium disilicate ceramics. A profound advantage is their high strength at thin geometries preserving their mechanical integrity. Based on the reviewed articles, monolithic zirconia ceramics cause minimal wear of antagonists, especially if appropriately polished, although no evidence still exists regarding the ultra-translucent compositions. Concerning the survival of monolithic zirconia restorations, the present review demonstrates the findings of the existing short-term studies, which reveal promising results after evaluating their performance for up to 5 or 7 years. Although a significant increase in translucency has been achieved, new translucent monolithic zirconia ceramics have to be further evaluated both in vitro and in vivo for their long-term potential to preserve their outstanding properties. Due to limited studies evaluating the wear properties of ultra-translucent material, no sound conclusions can be made, whereas well-designed clinical studies are urgently needed to enlighten issues of prognosis and long-term survival.

Toothpaste Composition Effect on Enamel Chromatic and Morphological Characteristics: In Vitro Analysis

The aim of this in vitro study was to assess the effect of toothpastes, with different compositions, on optical and morphological features of sound and demineralized enamel. We selected twenty-five teeth, recently extracted for orthodontic purposes, for this in vitro study. The teeth were caries free, without stains, fissures, filling or hypoplasia observed at inspection under standard conditions. Teeth were brushed (for 2–3 min, twice a day, for 21 days), with five different toothpastes (four commercially available and an experimental one) containing fluoride and hydroxyapatite. After that, teeth were demineralized with 37% orthophosforic acid (Ultra Etch^®, Ultradent Products Inc., South Jordan, UT, USA) for 60 s. We repeated the brushing protocol for another 21 days on demineralized enamel. Enamel vestibular surfaces were examined using a spectrophotometer (Vita EasyShade -Vita Zahnfabrik, Bad Sackingen, Germany) and a Scanning Electron Microscope (Inspect S^®, FEI Company, Hillsboro, OR, USA). Differences were statistically significant for colour parameters L* and ΔE*. SEM evaluation reveals demineralized enamel mineral gain after brushing with selected toothpastes. Toothpastes with specific ingredients can represent a balance between aesthetic and mineralization, and an oral hygiene correct algorithm is able to preserve enamel characteristics during ortodontic treatement with fixed appliances.

Adhesion to Zirconia: A Systematic Review of Current Conditioning Methods and Bonding Materials

Background. Reliable bonding between resin composite cements and high strength ceramics is difficult to achieve because of their chemical inertness and lack of silica content that makes etching impossible. The purpose of this review is to classify and analyze the existing methods and materials suggested to improve the adhesion of zirconia to dental substrate by using composite resins, in order to explore current trends in surface conditioning methods with predictable results. Methods. The current literature, examining the bond strength of zirconia ceramics, and including in vitro studies, clinical studies, and a systematic review, was analyzed. The research in the literature was carried out using PubMed and Cochrane Library databases, only papers in English, published online from 2013 to 2018. The following keywords and their combinations were used: Zirconia, 3Y-TZP, Adhesion, Adhesive cementation, Bonding, Resin, Composite resin, Composite material, Dentin, Enamel. Results. Research, in PubMed and Cochrane Library databases, provided 390 titles with abstracts. From these, a total of 93 publications were chosen for analysis. After a full text evaluation, seven articles were discarded. Therefore, the final sample was 86, including in vitro, clinical studies, and one systematic review. Various adhesive techniques with different testing methods were examined. Conclusions. Airborne-particle abrasion and tribo-chemical silica coating are the pre-treatment methods with more evidence in the literature. Increased adhesion could be expected after physico-chemical conditioning of zirconia. Surface contamination has a negative effect on adhesion. There is no evidence to support a universal adhesion protocol.