Particle sizes of infectious aerosols: implications for infection control

Decontamination Assessment of Nanofiber-based N95 Masks

As the world battles with the outbreak of the novel coronavirus, it also prepares for future global pandemics that threaten our health, economy, and survivor. During the outbreak, it became evident that use of personal protective equipment (PPE), specially face masks, can significantly slow the otherwise uncontrolled spread of the virus. Nevertheless, the outbreak and its new variants have caused shortage of PPE in many regions of the world. In addition, waste management of the enormous economical and environmental footprint of single use PPE has proven to be a challenge. Therefore, this study advances the theme of decontaminating used masks. More specifically, the effect of various decontamination techniques on the integrity and functionality of nanofiber-based N95 masks (i.e. capable of at least filtering 95% of 0.3 μm aerosols) were examined. These techniques include 70% ethanol, bleaching, boiling, steaming, ironing as well as placement in autoclave, oven, and exposure to microwave (MW) and ultraviolet (UV) light. Herein, filtration efficiency (by Particle Filtration Efficiency equipment), general morphology, and microstructure of nanofibers (by Field Emission Scanning Electron microscopy) prior and after every decontamination technique were observed. The results suggest that decontamination of masks with 70% ethanol can lead to significant unfavorable changes in the microstructure and filtration efficiency (down to 57.33%) of the masks. In other techniques such as bleaching, boiling, steaming, ironing and placement in the oven, filtration efficiency dropped to only about 80% and in addition, some morphological changes in the nanofiber microstructure were seen. Expectedly, there was no significant reduction in filtration efficiency nor microstructural changes in the case of placement in autoclave and exposure to the UV light. It was concluded that, the latter methods are preferable to decontaminate nanofiber-based N95 masks.

Aerosol transmission of human pathogens: From miasmata to modern viral pandemics and their preservation potential in the Anthropocene record

Ongoing uncertainty over the relative importance of aerosol transmission of COVID-19 is in part rooted in the history of medical science and our understanding of how epidemic diseases can spread through human populations. Ancient Greek medical theory held that such illnesses are transmitted by airborne pathogenic emanations containing particulate matter ("miasmata"). Notable Roman and medieval scholars such as Varro, Ibn al-Khatib and Fracastoro developed these ideas, combining them with early germ theory and the concept of contagion. A widely held but vaguely defined belief in toxic miasmatic mists as a dominant causative agent in disease propagation was overtaken by the science of 19th century microbiology and epidemiology, especially in the study of cholera, which was proven to be mainly transmitted by contaminated water. Airborne disease transmission came to be viewed as burdened by a dubious historical reputation and difficult to demonstrate convincingly. A breakthrough came with the classic mid-20th century work of Wells, Riley and Mills who proved how expiratory aerosols (their "droplet nuclei") could transport still-infectious tuberculosis bacteria through ventilation systems. The topic of aerosol transmission of pathogenic respiratory diseases assumed a new dimension with the mid-late 20th century "Great Acceleration" of an increasingly hypermobile human population repeatedly infected by different strains of zoonotic viruses, and has taken centre stage this century in response to outbreaks of new respiratory infections that include coronaviruses. From a geoscience perspective, the consequences of pandemic-status diseases such as COVID-19, produced by viral pathogens utilising aerosols to infect a human population currently approaching 8 billion, are far-reaching and unprecedented. The obvious and sudden impacts on for example waste plastic production, water and air quality and atmospheric chemistry are accelerating human awareness of current environmental challenges. As such, the "anthropause" lockdown enforced by COVID-19 may come to be seen as a harbinger of change great enough to be preserved in the Anthropocene stratal record.

Bioaerosol distribution characteristics and potential SARS-CoV-2 infection risk in a multi-compartment dental clinic

Dental clinics have a potential risk of infection, particularly during the COVID-19 pandemic. Multi-compartment dental clinics are widely used in general hospitals and independent clinics. This study utilised computational fluid dynamics to investigate the bioaerosol distribution characteristics in a multi-compartment dental clinic through spatiotemporal distribution, working area time-varying concentrations, and key surface deposition. The infection probability of SARS-CoV-2 for the dental staff and patients was calculated using the Wells-Riley model. In addition, the accuracy of the numerical model was verified by field measurements of aerosol concentrations performed during a clinical ultrasonic scaling procedure. The results showed that bioaerosols were mainly distributed in the compartments where the patients were treated. The average infection probability was 3.8% for dental staff. The average deposition number per unit area of the treatment chair and table are 28729 pcs/m² and 7945 pcs/m², respectively, which creates a possible contact transmission risk. Moreover, there was a certain cross-infection risk in adjacent compartments, and the average infection probability for patients was 0.84%. The bioaerosol concentrations of the working area in each compartment 30 min post-treatment were reduced to 0.07% of those during treatment, and the infection probability was <0.05%. The results will contribute to an in-depth understanding of the infection risk in multi-compartment dental clinics, forming feasible suggestions for management to efficiently support epidemic prevention and control in dental clinics.

Mycobacterium tuberculosis Transmission in High-Incidence Settings-New Paradigms and Insights

Tuberculosis has affected humankind for thousands of years, but a deeper understanding of its cause and transmission only arose after Robert Koch discovered Mycobacterium tuberculosis in 1882. Valuable insight has been gained since, but the accumulation of knowledge has been frustratingly slow and incomplete for a pathogen that remains the number one infectious disease killer on the planet. Contrast that to the rapid progress that has been made in our understanding SARS-CoV-2 (the cause of COVID-19) aerobiology and transmission. In this Review, we discuss important historical and contemporary insights into M. tuberculosis transmission. Historical insights describing the principles of aerosol transmission, as well as relevant pathogen, host and environment factors are described. Furthermore, novel insights into asymptomatic and subclinical tuberculosis, and the potential role this may play in population-level transmission is discussed. Progress towards understanding the full spectrum of M. tuberculosis transmission in high-burden settings has been hampered by sub-optimal diagnostic tools, limited basic science exploration and inadequate study designs. We propose that, as a tuberculosis field, we must learn from and capitalize on the novel insights and methods that have been developed to investigate SARS-CoV-2 transmission to limit ongoing tuberculosis transmission, which sustains the global pandemic.

Has the COVID-19 pandemic converged across countries?

The outbreak of COVID-19 has induced economic and financial disruptions to global economies, consistent with those experienced during previous episodes of economic or financial crises. This study offers a critical perspective into the spread of the virus by investigating the convergence patterns of COVID-19 across 155 countries from March 2020 to August 2021. The club clustering algorithm is used to verify the convergence patterns of infection and death rates in these countries. The findings show that full panel convergence cannot be achieved indicating the presence of sub-convergent clusters. Cluster formation for death rates includes the Americas, Africa, the Middle East, and Asia, among others. To understand the factors driving these results, we analyse the determinants of the convergence process of COVID-19. The probability of belonging to a cluster with higher death intensity increases with being above the age of 65, poverty, and for female smokers while handwashing shows beneficial effect on case intensity.

Materials analysis and image-based modelling of transmissibility and strain behaviour in approved face mask microstructures

Comparisons are made between six different approved face masks concerning their particle transmissibility allied to mechanical properties. The latter involves material testing and stretch or strain behaviour under load. SEM and X-ray elemental analyses showed contrasting structures between random and ordered fibre orientations. These constitute the mask designs where transmissibility is to be minimised. Airflow velocity measurement enabled filtration to be measured between the different mask designs, from two to six layers of different fabrics in combination. SEM provided the fibre diameter and pore size of each mask layer, up to a maximum of six. Stretching each complete mask showed its elasticity and recovery behaviour on an energy basis. The energy conversion involved in mask straining involves areas enclosed within steady and cyclic load-extension plots. Thus, the work done in extending a mask and the energy recovered from its release identified a hysteresis associated with an irrecoverable permanent stretch to the mask fabric. Failure of individual layers, which occurred successively in extended stretch tests, appeared as a drop in a load-extension response. That change is associated with permanent damage to each mask and friction contact within the rearrangement of loose fibre weaves. Masks with the greatest number of layers reduced particle transmissibility. However, woven or ordered mask fabrics in two layers with different orientations provided comparable performance. Simulation of each mechanical response, velocity streamlining and fibre distribution within the mask layers are also presented.

Ventilation reconstruction in bathrooms for restraining hazardous plume: Mitigate COVID-19 and beyond

Converging evidence reports that the probability of vertical transmission patterns via shared drainage systems, may be responsible for the huge contactless community outbreak in high-rise buildings. Publications indicate that a faulty bathroom exhaust fan system is ineffective in removing lifted hazardous virus-laden aerosols from the toilet bowl space. Common strategies (boosting ventilation capability and applying disinfection tablets) seem unsustainable and remain to date untested. Using combined simulation and experimental approaches, we compared three ventilation schemes in a family bathroom including the traditional ceiling fan, floor fan, and side-wall fan. We found that the traditional ceiling fan was barely functional whereby aerosol particles were not being adequately removed. Conversely, a side-wall fan could function efficiently and an enhanced ventilation capability can have increased performance whereby nearly 80.9% of the lifted aerosol particles were removed. There exists a common, and easily-overlooked mistake in the layout of the bathroom, exposing occupants to a contactless vertical pathogen aerosol transmission route. Corrections and dissemination are thus imperative for the reconstruction of these types of family bathrooms. Our findings provide evidence for the bathroom and smart ventilation system upgrade, promoting indoor public health and human hygiene.

Quantification of how mechanical ventilation influences the airborne infection risk of COVID-19 and HVAC energy consumption in office buildings

This paper presents an EnergyPlus-based parametric analysis to investigate the infection risk of Coronavirus Disease 2019 (COVID-19) under different mechanical ventilation scenarios for a typical medium-sized office building in various climate zones. A Wells-Riley (WR) based Gammaitoni-Nucci (GN) model was employed to quantitatively calculate the airborne infection risk. The selected parameters for the parametric analysis include the climate zone, outdoor air fraction, fraction of infectors, quanta generation rate, and exposure time. The loss and deposition of particles are not considered. The results suggest that the COVID-19 infection risk varies significantly with climate and season under different outdoor air fraction scenarios since the building heating and cooling load fundamentally impacts the supply airflow rate and thus directly influences the amount of mechanical ventilation, which determines the dilution ratio of contaminants. This risk assessment identified the climate zones that benefit the most and the least from increasing the outdoor air fraction. The climate zones such as 1A (Honolulu, HI), 2B (Tucson, AZ), 3A (Atlanta, GA), and 7 (International Falls, MN) are the most energy-efficient locations when it comes to increasing the outdoor air fraction to reduce the COVID-19 infection risk. In contrast, the climate zones such as 6A (Rochester, MN) and 6B (Great Falls, MT) are the least energy-efficient ones. This paper facilitates understanding a widely recommended COVID-19 risk mitigation strategy (i.e., increase the outdoor airflow rate) from the perspective of energy consumption.

Electronic Supplementary Material

Supplementary material is available for this article at 10.1007/s12273-022-0937-5 and is accessible for authorized users.

Ceiling impact on air disinfection performance of Upper-Room Germicidal Ultraviolet (UR-GUV)

This study used Computational Fluid Dynamics (CFD) to investigate air disinfection for SARS-CoV-2 by the Upper-Room Germicidal Ultraviolet (UR-GUV), with focus on ceiling impact. The study includes three indoor settings, i.e., low (airport bus), medium (classroom) and high (rehearsal room) ceilings, which were ventilated with 100% clean air (CA case), 80% air-recirculation with a low filtration (LF case), and 80% air-recirculation with a high filtration (HF case). According to the results, using UR-GUV can offset the increased infection risk caused by air recirculation, with viral concentrations in near field (NF) and far field (FF) in the LF case similar to those in the CA case. In the CA case, fraction remaining (FR) was 0.48-0.73 with 25% occupancy rate (OR) and 0.49-0.91 with 45% OR in the bus, 0.41 in NF and 0.11 in FF in the classroom, and 0.18 in NF and 0.09 in FF in the rehearsal room. Obviously, UR-GUV performance in NF can be improved in a room with a high ceiling where FR has a power relationship with UV zone height. As using UR-GUV can only extend the exposure time to get infection risk of 1% (T 1% ) to 8 min in NF in the classroom, and 47 min in NF in the rehearsal room, it is necessary to abide by social distancing in the two rooms. In addition, T 1% in FF was calculated to be 18.3 min with 25% OR and 21.4% with 45% OR in the airport bus, showing the necessity to further wear a mask.

Explosive COVID-19 outbreak in a German nursing home and the possible role of the air ventilation system

Background

Most COVID-19 outbreaks in nursing homes are explained by transmission of SARS-CoV-2 from nurses or visitors.

Methods and results

We describe an outbreak with 64 of the 67 residents identified as COVID-19 cases within two weeks (34 in nursing block 1, 30 in nursing block 2), at least 32 of them had relevant symptoms of COVID-19. Thirteen of the residents’ deaths were associated with COVID-19. In addition, 27 of approximately 60 staff members were identified as COVID-19 cases, 23 of them had relevant symptoms. In none of the samples from residents or staff was a mutation of SARS-CoV-2 detected. Quarantine of the residents was already in force at the beginning of the outbreak. A common source among the staff was considered to be unlikely because the two nursing home blocks had no staff rotation and the staff had to wear FFP2 masks during contact with residents. Three months after the outbreak the RNA of SARS-CoV-2 was detected on 14 of 39 sampled indoor surfaces of the air ventilation system with Ct values between 34.9 and 41.9, but only at the air supply in the corridor (11 of 24 samples) and the air overflow in the door between the corridor and the residents’ rooms (three of 11 samples) but not at the air exhaust in the residents’ bathrooms.

Conclusions

The air ventilation system and an inversion weather situation three days before the first confirmed case may have enhanced viral spread inside the nursing home assuming that a common source with a high viral load had existed at the time of outbreak.

Airborne infection risk of inter-unit dispersion through semi-shaded openings: A case study of a multi-storey building with external louvers

Building design for natural ventilation and indoor air quality have become increasingly important during the past decades. Investigating airflow routes of airborne transmission and evaluating the potential infection risk in the multi-storey building is helpful to the reduction of airborne transmission. Therefore, this study applies computational fluid dynamics simulations to investigate the inter-unit dispersion pattern of gaseous pollutant between different units through semi-shaded openings. The airflow exchange and pollutant dispersion in a multi-storey building is driven by wind-induced natural ventilation. External shading louvers, which are widely used in building facades to reduce heat gain from solar radiation, are chosen to establish the semi-shaded environment. Experimental validation is performed to make sure the accuracy of numerical settings in airflow investigation of semi-shaded openings. The airflow characteristics around semi-shaded openings is analyzed in the numerical simulations. The re-entry ratio of tracer gas and the airborne infection risk of COVID-19 is investigated in the cases with different louvers' locations and source units. The results show that the airflow is commonly slower in the semi-shaded space between louvers and openings. But the ventilation rate is not always consistent with the airflow speed because of the diversion effect from louver slats. The inter-unit infectious risk in the worst unit rises from 7.82% to 26.17% for windward shading, while it rises from 7.89% to 22.52% for leeward shading. These results are helpful to the further understanding of inter-unit transmission of infectious respiratory aerosols through external openings with complex structures.

Inhalable dry powder mRNA vaccines based on extracellular vesicles

Respiratory diseases are a global burden, with millions of deaths attributed to pulmonary illnesses and dysfunctions. Therapeutics have been developed, but they present major limitations regarding pulmonary bioavailability and product stability. To circumvent such limitations, we developed room-temperature-stable inhalable lung-derived extracellular vesicles or exosomes (Lung-Exos) as mRNA and protein drug carriers. Compared with standard synthetic nanoparticle liposomes (Lipos), Lung-Exos exhibited superior distribution to the bronchioles and parenchyma and are deliverable to the lungs of rodents and nonhuman primates (NHPs) by dry powder inhalation. In a vaccine application, severe acute respiratory coronavirus 2 (SARS-CoV-2) spike (S) protein encoding mRNA-loaded Lung-Exos (S-Exos) elicited greater immunoglobulin G (IgG) and secretory IgA (SIgA) responses than its loaded liposome (S-Lipo) counterpart. Importantly, S-Exos remained functional at room-temperature storage for one month. Our results suggest that extracellular vesicles can serve as an inhaled mRNA drug-delivery system that is superior to synthetic liposomes.

A full-face mask for protection against respiratory infections

BACKGROUND

Aerosols and droplets are the transmission routes of many respiratory infectious diseases. The COVID-19 management guidance recommends against the use of nebulized inhalation therapy directly in the emergency room or in an ambulance to prevent possible viral transmission. The three-dimensional printing method was used to develop an aerosol inhalation treatment mask that can potentially prevent aerosol dispersion. We conducted this utility validation study to understand the practicability of this new nebulizer mask system.

RESULTS

The fit test confirmed that the filter can efficiently remove small particles. The different locations of the mask had an excellent fit with a high pressure making a proper face seal usability. The full-face mask appeared to optimize filtration with pressure and is an example of materials that perform well for improvised respiratory protection using this design. The filtering effect test confirmed that the contamination of designated locations could be protected when using the mask with filters. As in the clinical safety test, a total of 18 participants (10 [55.6%] females; aged 33.1 ± 0.6 years) were included in the final analysis. There were no significant changes in SPO2, EtCO2, HR, SBP, DBP, and RR at the beginning, 20th, 40th, or 60th minutes of the test (all p >.05). The discomfort of wearing a mask increased slightly after time but remained within the tolerable range. The vision clarity score did not significantly change during the test. The mask also passed the breathability test.

CONCLUSION

The results of our study showed that this mask performed adequately in the fit test, the filtering test, and the clinical safety test. The application of a full-face mask with antiviral properties, together with the newly designed shape of a respirator that respects the natural curves of a human face, will facilitate the production of personal protective equipment with a highly efficient filtration system.

METHODS

We conducted three independent tests in this validation study: (1) a fit test to calculate the particle number concentration and its association with potential leakage; (2) a filtering effect test to verify the mask's ability to contain aerosol spread; and (3) a clinical safety test to examine the clinical safety, comfortableness, and visual clarity of the mask.

Experimental and numerical evaluation of a new visor concept with aerodynamic sealing to protect medical professionals from contaminated droplets and aerosols

The fast spreading of the SARS-CoV-2 virus led to a significant increase in the demand for personal protective equipment (PPE). Healthcare professionals, mainly dentists, work near the patients, increasing their risk of infection. This paper investigates the effectiveness of an air-curtain sealing effect in a newly designed visor developed to reduce the risk of contracting a respiratory infection. This PPE was developed by computational fluid dynamics (CFD) modeling. CFD results show that the aerodynamic sealing in this PPE device effectively protects the user's face by 43% from a contaminated environment. The experiments considered two different tests: one using a tracer gas (CO₂ ) to simulate a gaseous contaminant inside and outside the PPE face shield and a second test using smoke to simulate aerosol transport and evaluate the PPE efficiency. The particle concentration within the aerodynamically sealed PPE was evaluated and compared with the protection efficiency of other PPE. Results show similar protection levels for particles in the 1-5 μm range between the prototype and a KN95 respirator. The combined use of this novel PPE with aerodynamic sealing and a physical mask (KN95 or surgical) produced protection efficiency values within the range of 57%-70% for particles greater than 0.5 μm. This study reveals the potential of using an air curtain combined with a face shield to reduce the risks from contaminated environments.

Evaluation of expelled droplets through traditional Islamic face coverings

BACKGROUND

Expelled droplet count is an important factor when investigating the efficacy of face coverings since higher droplet counts indicate an increased possibility of disease transmission for airborne viruses such as COVID-19. While there is some published work relating facemask style to expelled droplet count during speech, there is no published data regarding the effectiveness of traditional Islamic face coverings such as the ghutra and niqab commonly worn by men and women in the Arabian Peninsula.

OBJECTIVES

Measure the effectiveness of worn traditional Islamic face coverings in reducing expelled droplet count during speech.

DESIGN

Experimental study SETTING: Biomedical engineering department at a university in Saudi Arabia.

MATERIALS AND METHODS

Using a previously described low-cost method for quantifying expelled droplets, this study compares droplet counts through commonly worn traditional Islamic face coverings and conventional three-ply surgical masks worn during speech. The device records scattered light from droplets (>5 μm diameter) as they pass through a laser light sheet (520 nm), and then video processing yields droplet counts.

MAIN OUTCOME MEASURES

Percent reduction in the number of expelled droplets passing through face coverings during speech compared to no face covering MAIN OUTCOME MEASURES: 9-15 recorded samples per face covering (n=3) plus no face covering control (n=1) in three females.

RESULTS

The average percent reduction for each mask type compared to no mask trial was 76% for the cotton ghutra, 93% for the niqab, and 95% for the surgical mask. The niqab and ghutra had relatively high variability in droplet reduction.

CONCLUSIONS

Traditional Islamic face coverings block some expelled droplets, but at lower rates than surgical masks. High standard deviations within facemask groups with high variability in fit (i.e., the cotton ghutra) further denote the importance of fit in face covering effectiveness. Some protection from airborne viruses is likely with traditional Islamic face coverings compared to no mask, but the amount of protection depends on the fit of the face covering.

LIMITATIONS

Detectable droplets limited to particles greater than 5 μm diameter with forward expulsion direction.

CONFLICT OF INTEREST

None.

Characterizing respiratory aerosol emissions during sustained phonation

OBJECTIVE

To elucidate the role of phonation frequency (i.e., pitch) and intensity of speech on respiratory aerosol emissions during sustained phonations.

METHODS

Respiratory aerosol emissions are measured in 40 (24 males and 16 females) healthy, non-trained singers phonating the phoneme /a/ at seven specific frequencies at varying vocal intensity levels.

RESULTS

Increasing frequency of phonation was positively correlated with particle production (r = 0.28, p < 0.001). Particle production rate was also positively correlated (r = 0.37, p < 0.001) with the vocal intensity of phonation, confirming previously reported findings. The primary mode (particle diameter ~0.6 μm) and width of the particle number size distribution were independent of frequency and vocal intensity. Regression models of the particle production rate using frequency, vocal intensity, and the individual subject as predictor variables only produced goodness of fit of adjusted R² = 40% (p < 0.001). Finally, it is proposed that superemitters be defined as statistical outliers, which resulted in the identification of one superemitter in the sample of 40 participants.

SIGNIFICANCE

The results suggest there remain unexplored effects (e.g., biomechanical, environmental, behavioral, etc.) that contribute to the high variability in respiratory particle production rates, which ranged from 0.2 particles/s to 142 particles/s across all trials. This is evidenced as well by changes in the distribution of participant particle production that transitions to a more bimodal distribution (second mode at particle diameter ~2 μm) at higher frequencies and vocal intensity levels.

The physics of respiratory particle generation, fate in the air, and inhalation

Given that breathing is one of the most fundamental physiological functions, there is an urgent need to broaden our understanding of the fluid dynamics that governs it. There would be many benefits from doing so, including a better assessment of respiratory health, a basis for more precise delivery of pharmaceutical drugs for treatment, and the understanding and potential minimization of respiratory infection transmission. We review the physics of particle generation in the respiratory tract, the fate of these particles in the air on exhalation and the physics of particle inhalation. The main focus is on evidence from experimental studies. We conclude that although there is qualitative understanding of the generation of particles in the respiratory tract, a basic quantitative knowledge of the characteristics of the particles emitted during respiratory activities and their fate after emission, and a theoretical understanding of particle deposition during inhalation, nevertheless the general understanding of the entire process is rudimentary, and many open questions remain.

The Removal of Airborne Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) and Other Microbial Bioaerosols by Air Filtration on Coronavirus Disease 2019 (COVID-19) Surge Units

Airborne severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) was detected in a coronavirus disease 19 (COVID-19) ward before activation of HEPA-air filtration but not during filter operation; SARS-CoV-2 was again detected following filter deactivation. Airborne SARS-CoV-2 was infrequently detected in a COVID-19 intensive care unit. Bioaerosol was also effectively filtered.

Reducing the Effectiveness of Ward Particulate Matter, Bacteria and Influenza Virus by Combining Two Complementary Air Purifiers

Air purifiers should pay much attention to hospital-associated infections, but the role of a single air purifier is limited. The goal of this study was to evaluate the effectiveness of the combined application of the nonequilibrium positive and negative oxygen ion purifier (PNOI) and the high-efficiency particulate air filter (HEPA) on a complex, polluted environment. Two of the better performing purifiers were selected before the study. The efficacy of their use alone and in combination for purification of cigarette particulate matter (PM), Staphylococcus albicans, and influenza virus were then evaluated under a simulated contaminated ward. PNAI and HEPA alone are deficient. However, when they were combined, they achieved 98.44%, 99.75%, and 100% 30 min purification rates for cigarette PM, S. albus, and influenza virus, respectively. The purification of pollution of various particle sizes and positions was optimized and reduced differentials, and a subset of airborne influenza viruses is inactivated. Furthermore, they were superior to ultraviolet disinfection for microbial purification in air. This work demonstrates the strong purification capability of the combined application of these two air purifiers for complex air pollution, which provides a new idea for infection control in medical institutions.

Optimized mechanism for fast removal of infectious pathogen-laden aerosols in the negative-pressure unit

It has been frequently emphasized that highly contagious respiratory disease pathogens (such as SARS-CoV-2) are transmitted to the other hosts in the form of micro-sized aerosols (< 5 μm) in the air without physical contacts. Hospital environments such as negative-pressure unit are considered being consistently exposed to pathogens, so it is essential to quickly discharge them through the effective ventilation system. To achieve that, in the present study, we propose the optimized ventilation mechanism and design for the fastest removal of pathogen-laden aerosol using numerical simulations. We quantitatively evaluated the aerosol removal performance of various ventilation configurations (combinations of air exhaust and supply ducts), and found that the key mechanism is to form the coherent (preferentially upward) airflow structure to surround the respiratory flow containing the aerosol cluster. We believe that the present findings will play a critical role in developing the high-efficiency negative-pressure facility irrespective of its size and environments.

Comparative Dissemination of Aerosol and Splatter Using Suction Device during Ultrasonic Scaling: A Pilot Study

Objective: This study compared the aerosol and splatter diameter and count numbers produced by a dental mouth prop with a suction holder device and a saliva ejector during ultrasonic scaling in a clinical setting. Methodology: Fluorescein dye was placed in the dental equipment irrigation reservoirs with a mannequin, and an ultrasonic scaler was employed. The procedures were performed three times per device. The upper and bottom board papers were placed on the laboratory platform. All processes used an ultrasonic scaler to generate aerosol and splatter. A dental mouth prop with a suction holder and a saliva ejector were also tested. Photographic analysis was used to examine the fluorescein samples, followed by image processing in Python and assessment of the diameter and count number. For device comparison, statistics were used with an independent t-test. Result: When using the dental mouth prop with a suction holder, the scaler produced aerosol particles that were maintained on the upper board paper (mean ± SD: 1080 ± 662 µm) compared to on the bottom board paper (1230 ± 1020 µm). When the saliva ejector was used, it was found that the diameter of the aerosol on the upper board paper was 900 ± 580 µm, and the diameter on the bottom board paper was 1000 ± 756 µm. Conclusion: There was a significant difference in the aerosol and splatter particle diameter and count number between the dental mouth prop with a suction holder and saliva ejector (p < 0.05). Furthermore, the results revealed that there was a statistically significant difference between the two groups on the upper and bottom board papers.

What were the historical reasons for the resistance to recognizing airborne transmission during the COVID-19 pandemic?

The question of whether SARS-CoV-2 is mainly transmitted by droplets or aerosols has been highly controversial. We sought to explain this controversy through a historical analysis of transmission research in other diseases. For most of human history, the dominant paradigm was that many diseases were carried by the air, often over long distances and in a phantasmagorical way. This miasmatic paradigm was challenged in the mid to late 19th century with the rise of germ theory, and as diseases such as cholera, puerperal fever, and malaria were found to actually transmit in other ways. Motivated by his views on the importance of contact/droplet infection, and the resistance he encountered from the remaining influence of miasma theory, prominent public health official Charles Chapin in 1910 helped initiate a successful paradigm shift, deeming airborne transmission most unlikely. This new paradigm became dominant. However, the lack of understanding of aerosols led to systematic errors in the interpretation of research evidence on transmission pathways. For the next five decades, airborne transmission was considered of negligible or minor importance for all major respiratory diseases, until a demonstration of airborne transmission of tuberculosis (which had been mistakenly thought to be transmitted by droplets) in 1962. The contact/droplet paradigm remained dominant, and only a few diseases were widely accepted as airborne before COVID-19: those that were clearly transmitted to people not in the same room. The acceleration of interdisciplinary research inspired by the COVID-19 pandemic has shown that airborne transmission is a major mode of transmission for this disease, and is likely to be significant for many respiratory infectious diseases.

COVID-19 in the Airline Industry: The Good, the Bad, and the Necessary

The COVID-19 pandemic has significantly affected flight attendants' health, safety, and security. Members of this group work in a densely occupied and enclosed space where social distancing is virtually impossible, compliance with mask rules is uneven, aggressive passenger incidents are at an all-time high, and the vaccination status of passengers on domestic flights is unknown. Here is a description of the response by the federal government and the United States (U.S.) airline industry from the perspective of a flight attendant union between the early days of the COVID-19 pandemic and this writing. Specifically, the issues of ventilation, face masks, aggressive passengers, quarantine and isolation, and vaccinations are reviewed, including actions taken by the executive branch of the U.S. government, regulators, airlines, manufacturers, and our crew member union. Although there will be regional differences around the globe, many of these issues are universal.

Maintaining safe office spaces to minimise risks of SARS-CoV-2 transmission

BACKGROUND

SARS-CoV-2 can be transmitted within offices. Traditional respiratory transmission modes have undergone reassessment and a new paradigm has emerged. This paradigm needs examining prior to identifying control measures to prevent office acquired infections (OAI).

METHODS

An ongoing assessment of the SARS-CoV-2 transmission literature, including international public health guidance, began 30/1/2020 and continued to submission 7/2/2022. The evidence for the established respiratory transmission paradigm (either droplet or aerosols) and that of a newly emerging paradigm (aerosol and/or droplets) were explored. Based on the new paradigm control measures needed to minimise OAI were produced.

RESULTS

The old paradigm of respiratory transmission of being either droplet or airborne cannot be evidenced. SARS-CoV-2 is emitted in virus laden particles that can be inhaled and/or sprayed on facial mucous membranes (Airborne being the dominant route). Office hygiene measures include: minimising the opportunities for the virus to enter the building. Reducing the susceptibility of people to the virus. Minimising exposure risks within offices, and optimising success in deployment.

CONCLUSION

Standard office hygiene precautions are needed to reduce OAI risks from SARS-CoV-2. Efforts should focus on enabling the smooth functioning of the office whilst minimising risks that the virus will transmit therein. This includes: local risk assessments as transmission risks vary based on building design, ventilation, capacity, and ways of working. Additionally, using experts to optimise ventilation systems.

SARS-CoV-2 air sampling: A systematic review on the methodologies for detection and infectivity

This systematic review aims to present an overview of the current aerosol sampling methods (and equipment) being used to investigate the presence of SARS-CoV-2 in the air, along with the main parameters reported in the studies that are essential to analyze the advantages and disadvantages of each method and perspectives for future research regarding this mode of transmission. A systematic literature review was performed on PubMed/MEDLINE, Web of Science, and Scopus to assess the current air sampling methodologies being applied to SARS-CoV-2. Most of the studies took place in indoor environments and healthcare settings and included air and environmental sampling. The collection mechanisms used were impinger, cyclone, impactor, filters, water-based condensation, and passive sampling. Most of the reviewed studies used RT-PCR to test the presence of SARS-CoV-2 RNA in the collected samples. SARS-CoV-2 RNA was detected with all collection mechanisms. From the studies detecting the presence of SARS-CoV-2 RNA, fourteen assessed infectivity. Five studies detected viable viruses using impactor, water-based condensation, and cyclone collection mechanisms. There is a need for a standardized protocol for sampling SARS-CoV-2 in air, which should also account for other influencing parameters, including air exchange ratio in the room sampled, relative humidity, temperature, and lighting conditions.

An application for relating Legionella shower water monitoring results to estimated health outcomes

Exposure models are useful tools for relating environmental monitoring data to expected health outcomes. The objective of this study was to (1) compare two Legionella shower exposure models, and (2) develop a risk calculator tool for relating environmental monitoring data to estimated Legionella infection risks and Legionnaires' Disease (LD) illness risks. Legionella infection risks for a single shower event were compared using two shower Legionella exposure models. These models varied in their description of partitioning of Legionella in aerosols and aerosol deposition in the lung, where Model 1 had larger and fewer aerosol ranges than Model 2. Model 2 described conventional vs. water efficient showers separately, while Model 1 described exposure for an unspecified shower type (did not describe it as conventional or water efficient). A Monte Carlo approach was used to account for variability and uncertainty in these aerosolization and deposition parameters, Legionella concentrations, and the dose-response parameter. Methods for relating infection risks to illness risks accounting for demographic differences were used to inform the risk calculator web application ("app"). Model 2 consistently estimated higher infection risks than Model 1 for the same Legionella concentration in water and estimated deposited doses with less variability. For a 7.8-min shower with a Legionella concentration of 0.1 CFU/mL, the average infection risks estimated using Model 2 were 4.8 × 10^-6 (SD=3.0 × 10^-6) (conventional shower) and 2.3 × 10^-6 (SD=1.7 × 10^-6) (water efficient). Average infection risk estimated by Model 1 was 1.1 × 10^-6 (SD=9.7 × 10^-7). Model 2 was used for app development due to more conservative risk estimates and less variability in estimated dose. While multiple Legionella shower models are available for quantitative microbial risk assessments (QMRAs), they may yield notably different infection risks for the same environmental microbial concentration. Model comparisons will inform decisions regarding their integration with risk assessment tools. The development of risk calculator tools for relating environmental microbiology data to infection risks will increase the impact of exposure models for informing water treatment decisions and achieving risk targets.

Effect of Grit Size on Airborne Particle Concentration and Size Distribution during Oak Wood Sanding

Adverse health effects caused by exposure to airborne particles have been detected in recent years, however there is little knowledge about exposure to ultrafine particles with a diameter <100 nm. In this study, particle number concentration and size distribution in a range of particle diameters from 10 nm to 10 µm were determined during oak wood sanding. A hand-held orbit sander in combination with three types of grit size (P60, 120 and 240) of sandpaper were used. Measurements were obtained using a portable particle size distribution analyzer and an optical particle size spectrometer, carried out at 15-min intervals for each treatment by static sampling in the breathing zone. We also compared the optical particle size spectrometer to the aerosol monitor in order to evaluate the mass concentration of airborne particles in the range of 1 to 10 µm in diameter. Sanding paper with the finest grit, P240, showed a significantly higher number concentration of ultrafine particles, compared with P60 and P120 grits. The differences among particular grit size were statistically significant for microparticles. The size distribution of particles during sanding was not affected by grit size. For each grit size, apparent peak values of ultrafine and microparticle number concentrations were determined at approximately 15 nm, and 0.1 µm, respectively. Optical particle size spectrometer and aerosol monitor showed comparable results of mass concentration for the respirable fraction.

Exhaled Aerosols in SARS-CoV-2 Polymerase Chain Reaction-Positive Children and Age-Matched-Negative Controls

Background

Children and adolescents seem to be less affected by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) disease in terms of severity, especially until the increasing spread of the omicron variant in December 2021. Anatomical structures and lower number of exhaled aerosols may in part explain this phenomenon. In a cohort of healthy and SARS-CoV-2 infected children, we compared exhaled particle counts to gain further insights about the spreading of SARS-CoV-2.

Materials and Methods

In this single-center prospective observational trial, a total of 162 children and adolescents (age 6-17 years), of whom 39 were polymerase chain reaction (PCR)-positive for SARS-CoV-2 and 123 PCR-negative, were included. The 39 PCR-positive children were compared to 39 PCR-negative age-matched controls. The data of all PCR-negative children were analyzed to determine baseline exhaled particle counts in children. In addition, medical and clinical history was obtained and spirometry was measured.

Results

Baseline exhaled particle counts were low in healthy children. Exhaled particle counts were significantly increased in SARS-CoV-2 PCR-positive children (median 355.0/L; range 81-6955/L), compared to age-matched -negative children (median 157.0/L; range 1-533/L; p < 0.001).

Conclusion

SARS-CoV-2 PCR-positive children exhaled significantly higher levels of aerosols than healthy children. Overall children had low levels of exhaled particle counts, possibly indicating that children are not the major driver of the SARS-CoV-2 pandemic.

Trial Registration

[ClinicalTrials.gov], Identifier [NCT04739020].

Hybrid measurement of respiratory aerosol reveals a dominant coarse fraction resulting from speech that remains airborne for minutes

Respiratory droplets are widely recognized as the primary vehicle in viral respiratory disease transmission. Accurate information on their number and size distributions is important for appropriate mitigation strategies, for quantitative modeling of airborne disease transmission, and for evaluating the relative importance of droplets originating from saliva versus airway lining fluid. A straightforward experimental setup using inexpensive, readily available components is developed for simultaneous characterization of larger particles by video analysis of laser light scattering and monitoring of smaller sizes by an optical particle counter. Measurements indicate that in a healthy volunteer, the airborne mass of speech aerosol far exceeds that generated by breathing, even when accounting for faster sedimentation of the larger particles.

Accurate measurements of the size and quantity of aerosols generated by various human activities in different environments are required for efficacious mitigation strategies and accurate modeling of respiratory disease transmission. Previous studies of speech droplets, using standard aerosol instrumentation, reported very few particles larger than 5 μm. This starkly contrasts with the abundance of such particles seen in both historical slide deposition measurements and more recent light scattering observations. We have reconciled this discrepancy by developing an alternative experimental approach that addresses complications arising from nucleated condensation. Measurements reveal that a large volume fraction of speech-generated aerosol has diameters in the 5- to 20-μm range, making them sufficiently small to remain airborne for minutes, not hours. This coarse aerosol is too large to penetrate the lower respiratory tract directly, and its relevance to disease transmission is consistent with the vast majority of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infections initiating in the upper respiratory tract. Our measurements suggest that in the absence of symptoms such as coughing or sneezing, the importance of speech-generated aerosol in the transmission of respiratory diseases is far greater than generally recognized.

The intersecting pandemics of tuberculosis and COVID-19: population-level and patient-level impact, clinical presentation, and corrective interventions

The global tuberculosis burden remains substantial, with more than 10 million people newly ill per year. Nevertheless, tuberculosis incidence has slowly declined over the past decade, and mortality has decreased by almost a third in tandem. This positive trend was abruptly reversed by the COVID-19 pandemic, which in many parts of the world has resulted in a substantial reduction in tuberculosis testing and case notifications, with an associated increase in mortality, taking global tuberculosis control back by roughly 10 years. Here, we consider points of intersection between the tuberculosis and COVID-19 pandemics, identifying wide-ranging approaches that could be taken to reverse the devastating effects of COVID-19 on tuberculosis control. We review the impact of COVID-19 at the population level on tuberculosis case detection, morbidity and mortality, and the patient-level impact, including susceptibility to disease, clinical presentation, diagnosis, management, and prognosis. We propose strategies to reverse or mitigate the deleterious effects of COVID-19 and restore tuberculosis services. Finally, we highlight research priorities and major challenges and controversies that need to be addressed to restore and advance the global response to tuberculosis.

The cost-effectiveness of standalone HEPA filtration units for the prevention of airborne SARS CoV-2 transmission

OBJECTIVE

Airborne infection from aerosolized SARS-CoV-2 poses an economic challenge for businesses without existing heating, ventilation, and air conditioning (HVAC) systems. The Environmental Protection Agency notes that standalone units may be used in areas without existing HVAC systems, but the cost and effectiveness of standalone units has not been evaluated.

STUDY DESIGN

Cost-effectiveness analysis with Monte Carlo simulation and aerosol transmission modeling.

METHODS

We built a probabilistic decision-analytic model in a Monte Carlo simulation that examines aerosol transmission of SARS-CoV-2 in an indoor space. As a base case study, we built a model that simulated a poorly ventilated indoor 1000 square foot restaurant and the range of Covid-19 prevalence of actively infectious cases (best-case: 0.1%, base-case: 2%, and worst-case: 3%) and vaccination rates (best-case: 90%, base-case: 70%, and worst-case: 0%) in New York City. We evaluated the cost-effectiveness of improving ventilation rate to 12 air changes per hour (ACH), the equivalent of hospital-grade filtration systems used in emergency departments. We also provide a customizable online tool that allows the user to change model parameters.

RESULTS

All 3 scenarios resulted in a net cost-savings and infections averted. For the base-case scenario, improving ventilation to 12 ACH was associated with 54 [95% Credible Interval (CrI): 29-86] aerosol infections averted over 1 year, producing an estimated cost savings of $152,701 (95% CrI: $80,663, $249,501) and 1.35 (95% CrI: 0.72, 2.24) quality-adjusted life years (QALYs) gained.

CONCLUSIONS

It is cost-effective to improve indoor ventilation in small businesses in older buildings that lack HVAC systems during the pandemic.

Exposure Route Influences Disease Severity in the COVID-19 Cynomolgus Macaque Model

The emergence of SARS-CoV-2 and the subsequent pandemic has highlighted the need for animal models that faithfully replicate the salient features of COVID-19 disease in humans. These models are necessary for the rapid selection, testing, and evaluation of potential medical countermeasures. Here, we performed a direct comparison of two distinct routes of SARS-CoV-2 exposure—combined intratracheal/intranasal and small particle aerosol—in two nonhuman primate species, rhesus and cynomolgus macaques. While all four experimental groups displayed very few outward clinical signs, evidence of mild to moderate respiratory disease was present on radiographs and at necropsy. Cynomolgus macaques exposed via the aerosol route also developed the most consistent fever responses and had the most severe respiratory disease and pathology. This study demonstrates that while all four models produced suitable representations of mild COVID-like illness, aerosol exposure of cynomolgus macaques to SARS-CoV-2 produced the most severe disease, which may provide additional clinical endpoints for evaluating therapeutics and vaccines.

COVID-19-from emerging global threat to ongoing pandemic crisis

In December 2019, China witnessed the emergence of a novel coronavirus, SARS-CoV-2. Its ability to spread quickly made it a global pandemic. The United States has been greatly affected, with more than 980,000 lives lost so far. Diagnosis is made primarily through nasopharyngeal swab for polymerase chain reaction. Point-of-care testing by antigen is less sensitive and specific and may require polymerase chain reaction confirmation. Management of the COVID-19 patient remains largely supportive. Steroids are now a therapy mainstay if the patient is hypoxic. Direct antivirals, such as nirmatrelvir/ritonavir, remdesivir, or molnupirivir, can be used if certain criteria are met. SARS-CoV-2 is transmitted primarily by inhalation of large droplets, though transmission by aerosolization may occur, particularly via certain procedures. In the hospital setting, use of personal protective equipment for the care of COVID-19 patients has largely remained the same, with full use of gowns, gloves, respirators, and eye protection. Inadequate supply at the start of the pandemic required innovative ways to reprocess and extend the use of personal protective equipment. Three vaccines are now available in the US, all with excellent efficacy against severe disease and hospitalization, though booster doses are needed to bolster waning antibody levels. The possibility of emerging variants continues to remain a threat to control of the pandemic. The leader of the World Health Organization, Dr. Tedros, has stated, "The pandemic will not be over anywhere until it's over everywhere."

Fabrication of a highly protective 3D-printed mask and evaluation of its viral filtration efficiency using a human head mannequin

Facemasks are one of the most effective and low-cost prophylactics for COVID-19. In the spring 2020, when a severe shortage of facemasks occurred worldwide, various types of 3D-printed masks were designed and proposed. However, the protective effects conferred by most of these masks were not experimentally evaluated. Here, we provide a new simple design of 3D-printed mask and evaluate its protective effect in a viral filtration test using a human head mannequin. The developed mask can be constructed with a low-cost 3D printer, with an approximate production cost of US $4. This mask has three parts: the main part, wearing parts, and a piece of non-woven fabric filter. The volume of the filter, which needs to be changed daily, was reduced to approximately 1/10 of that of commercially available surgical masks used in this study. The developed mask is fabricated from polylactic acid, a biodegradable plastic, and its surface contour contacting the face may be adjusted after softening the material with hot water at 60-80°C. The viral filtration efficiency of the developed mask was found to be over 80%. This performance is better than that of commercially available facemasks, such as surgical masks and cloth masks, and equal to those of KN95 and KF94.

Modeling Clothing as a Vector for Transporting Airborne Particles and Pathogens across Indoor Microenvironments

Evidence suggests that human exposure to airborne particles and associated contaminants, including respiratory pathogens, can persist beyond a single microenvironment. By accumulating such contaminants from air, clothing may function as a transport vector and source of "secondary exposure". To investigate this function, a novel microenvironmental exposure modeling framework (ABICAM) was developed. This framework was applied to a para-occupational exposure scenario involving the deposition of viable SARS-CoV-2 in respiratory particles (0.5-20 μm) from a primary source onto clothing in a nonhealthcare setting and subsequent resuspension and secondary exposure in a car and home. Variability was assessed through Monte Carlo simulations. The total volume of infectious particles on the occupant's clothing immediately after work was 4800 μm3 (5th-95th percentiles: 870-32 000 μm3). This value was 61% (5-95%: 17-300%) of the occupant's primary inhalation exposure in the workplace while unmasked. By arrival at the occupant's home after a car commute, relatively rapid viral inactivation on cotton clothing had reduced the infectious volume on clothing by 80% (5-95%: 26-99%). Secondary inhalation exposure (after work) was low in the absence of close proximity and physical contact with contaminated clothing. In comparison, the average primary inhalation exposure in the workplace was higher by about 2-3 orders of magnitude. It remains theoretically possible that resuspension and physical contact with contaminated clothing can occasionally transmit SARS-CoV-2 between humans.

Epidemiologic characteristics and differential management strategies of seven case series with COVID-19 outbreaks caused by asymptomatic carriers from June 2020 to May 2021 in China

With the COVID-19 epidemic quickly under control in China in the early stage of 2020, global cooperation/communications may pose great challenges to epidemic control and prevention in the country. Large-scale spread by asymptomatic carriers was a concern. We obtained data on new cluster outbreak regions with COVID-19 caused by asymptomatic carriers from June 2020 to May 2021 in China, and reported the epidemiological characteristics, the possible routes of viral transmission and infection, and different control strategies. These results show the importance of regular screening for high-risk populations and differential management strategies for epidemic control, which provide an objective basis for suppressing the spread of the SARS-CoV-2 virus. These experiences can be used as a reference to minimize the subsequent spread of virus mutants in various places.

Assessing impact of ventilation on airborne transmission of SARS-CoV-2: a cross-sectional analysis of naturally ventilated healthcare settings in Bangladesh

OBJECTIVES

To evaluate the risk of exposure to SARS-CoV-2 in naturally ventilated hospital settings by measuring parameters of ventilation and comparing these findings with results of bioaerosol sampling.

STUDY DESIGN

Cross-sectional study.

STUDY SETTING AND STUDY SAMPLE

The study sample included nine hospitals in Dhaka, Bangladesh. Ventilation characteristics and air samples were collected from 86 healthcare spaces during October 2020 to February 2021.

PRIMARY OUTCOME

Risk of cumulative SARS-CoV-2 infection by type of healthcare area.

SECONDARY OUTCOMES

Ventilation rates by healthcare space; risk of airborne detection of SARS-CoV-2 across healthcare spaces; impact of room characteristics on absolute ventilation; SARS-CoV-2 detection by naturally ventilated versus mechanically ventilated spaces.

RESULTS

The majority (78.7%) of naturally ventilated patient care rooms had ventilation rates that fell short of the recommended ventilation rate of 60 L/s/p. Using a modified Wells-Riley equation and local COVID-19 case numbers, we found that over a 40-hour exposure period, outpatient departments posed the highest median risk for infection (7.7%). SARS-CoV-2 RNA was most frequently detected in air samples from non-COVID wards (50.0%) followed by outpatient departments (42.9%). Naturally ventilated spaces (22.6%) had higher rates of SARS-CoV-2 detection compared with mechanically ventilated spaces (8.3%), though the difference was not statistically significant (p=0.128). In multivariable linear regression with calculated elasticity, open door area and cross-ventilation were found to have a significant impact on ventilation.

CONCLUSION

Our findings provide evidence that naturally ventilated healthcare settings may pose a high risk for exposure to SARS-CoV-2, particularly among non-COVID-designated spaces, but improving parameters of ventilation can mitigate this risk.

Respirators in Healthcare: Material, Design, Regulatory, Environmental, and Economic Considerations for Clinical Efficacy

Maintaining an ample supply of personal protective equipment continues to be a challenge for the healthcare industry, especially during emergency situations and times of strain on the supply chain. Most critically, healthcare workers exposed to potential airborne hazards require sufficient respiratory protection. Respirators are the only type of personal protective equipment able to provide adequate respiratory protection. However, their ability to shield hazards depends on design, material, proper fit, and environmental conditions. As a result, not all respirators may be adequate for all scenarios. Additionally, factors including user comfort, ease of use, and cost contribute to respirator effectiveness. Therefore, a careful consideration of these parameters is essential for ensuring respiratory protection for those working in the healthcare industry. Here respirator design and material characteristics are reviewed, as well as properties of airborne hazards and potential filtration mechanisms, regulatory standards of governmental agencies, respirator efficacy in the clinical setting, attitude of healthcare personnel toward respiratory protection, and environmental and economic considerations of respirator manufacturing and distribution.

Aerosol generation during general anesthesia is comparable to coughing: An observational clinical study

BACKGROUND

Intubation, laryngoscopy, and extubation are considered highly aerosol-generating procedures, and additional safety protocols are used during COVID-19 pandemic in these procedures. However, previous studies are mainly experimental and have neither analyzed staff exposure to aerosol generation in the real-life operating room environment nor compared the exposure to aerosol concentrations generated during normal patient care. To assess operational staff exposure to potentially infectious particle generation during general anesthesia, we measured particle concentration and size distribution with patients undergoing surgery with Optical Particle Sizer.

METHODS

A single-center observative multidisciplinary clinical study in Helsinki University Hospital with 39 adult patients who underwent general anesthesia with tracheal intubation. Mean particle concentrations during different anesthesia procedures were statistically compared with cough control data collected from 37 volunteers to assess the differences in particle generation.

RESULTS

This study measured 25 preoxygenations, 30 mask ventilations, 28 intubations, and 24 extubations. The highest total aerosol concentration of 1153 particles (p)/cm³ was observed during mask ventilation. Preoxygenations, mask ventilations, and extubations as well as uncomplicated intubations generated mean aerosol concentrations statistically comparable to coughing. It is noteworthy that difficult intubation generated significantly fewer aerosols than either uncomplicated intubation (p = .007) or coughing (p = 0.006).

CONCLUSIONS

Anesthesia induction generates mainly small (<1 µm) aerosol particles. Based on our results, general anesthesia procedures are not highly aerosol-generating compared with coughing. Thus, their definition as high-risk aerosol-generating procedures should be re-evaluated due to comparable exposures during normal patient care.

IMPLICATION STATEMENT

The list of aerosol-generating procedures guides the use of protective equipments in hospitals. Intubation is listed as a high-risk aerosol-generating procedure, however, aerosol generation has not been measured thoroughly. We measured aerosol generation during general anesthesia. None of the general anesthesia procedures generated statistically more aerosols than coughing and thus should not be considered as higher risk compared to normal respiratory activities.

Nonpharmaceutical interventions to prevent viral respiratory infection in community settings: an umbrella review

Background

Respiratory viruses pose an important public health threat to most communities. Nonpharmaceutical interventions (NPIs) such as masks, hand hygiene or physical distancing, among others, are believed to play an important role in reducing transmission of respiratory viruses. In this umbrella review, we summarise the evidence of the effectiveness of NPIs for the prevention of respiratory virus transmission in the community setting.

Observations

A systematic search of PubMed, Embase, Medline and Cochrane reviews resulted in a total of 24 studies consisting of 11 systematic reviews and meta-analyses, 12 systematic reviews without meta-analyses and one standalone meta-analysis. The current evidence from these data suggests that hand hygiene is protective against respiratory viral infection. The use of hand hygiene and facemasks, facemasks alone and physical distancing were interventions with inconsistent evidence. Interventions such as school closures, oral hygiene or nasal saline rinses were shown to be effective in reducing the risk of influenza; however, the evidence is sparse and mostly of low and critically low quality.

Conclusions

Studies on the effectiveness of NPIs for the prevention of respiratory viral transmission in the community vary in study design, quality and reported effectiveness. Evidence for the use of hand hygiene or facemasks is the strongest; therefore, the most reasonable suggestion is to use hand hygiene and facemasks in the community setting.

Development of a combinatory filtration system for pollution and virus abatement by optimized nanoparticle deposition

PM2.5, particulate matter less than 2.5 microns, is the leading contributor to air pollution which results in cardio-vascular and respiratory diseases. Recent studies also indicate a strong correlation between ambient air pollution and COVID-19 cases, which have affected the lives of billions of people globally. Abatement technologies such as ionic and other high efficiency filtration systems are expensive and unaffordable in communities with limited resources. The goal of this study was to develop a mask with an optimized nanoparticle coating which has a dual capability of particulate matter and virus filtration, while being affordable and safe for human use. The nanoparticles were selected for their filtration and virucidal capabilities. Particle filtration efficiency, tested with a wind tunnel and PM2.5 from incense sticks measured by laser particle detectors, improved by ~60% with nanoparticle coatings on KN95 and surgical masks. Virus filtration efficiency, tested using nebulized NaCl particles as a virus surrogate, improved by 95% with coated masks. The nanoparticle retention efficacy, tested by simulating a normal 8-hour workday, was well within the permissible exposure limits. This technology has several applications such as in personal protective equipment for virus protection, and in air-conditioning and car cabin filters for pollution abatement. In conclusion, the chosen combination of nanoparticles provides an effective and safe solution for both particulate matter and viral particle filtration.

Far-UVC (222 nm) efficiently inactivates an airborne pathogen in a room-sized chamber

Many infectious diseases, including COVID-19, are transmitted by airborne pathogens. There is a need for effective environmental control measures which, ideally, are not reliant on human behaviour. One potential solution is Krypton Chloride (KrCl) excimer lamps (often referred to as Far-UVC), which can efficiently inactivate pathogens, such as coronaviruses and influenza, in air. Research demonstrates that when KrCl lamps are filtered to remove longer-wavelength ultraviolet emissions they do not induce acute reactions in the skin or eyes, nor delayed effects such as skin cancer. While there is laboratory evidence for Far-UVC efficacy, there is limited evidence in full-sized rooms. For the first time, we show that Far-UVC deployed in a room-sized chamber effectively inactivates aerosolised Staphylococcus aureus. At a room ventilation rate of 3 air-changes-per-hour (ACH), with 5 filtered-sources the steady-state pathogen load was reduced by 98.4% providing an additional 184 equivalent air changes (eACH). This reduction was achieved using Far-UVC irradiances consistent with current American Conference of Governmental Industrial Hygienists threshold limit values for skin for a continuous 8-h exposure. Our data indicate that Far-UVC is likely to be more effective against common airborne viruses, including SARS-CoV-2, than bacteria and should thus be an effective and "hands-off" technology to reduce airborne disease transmission. The findings provide room-scale data to support the design and development of effective Far-UVC systems.

Characterisation of Particle Size and Viability of SARS-CoV-2 Aerosols from a Range of Nebuliser Types Using a Novel Sampling Technique

Little is understood about the impact of nebulisation on the viability of SARS-CoV-2. In this study, a range of nebulisers with differing methods of aerosol generation were evaluated to determine SARS-CoV-2 viability following aerosolization. The aerosol particle size distribution was assessed using an aerosol particle sizer (APS) and SARS-CoV-2 viability was determined after collection into liquid media using All-Glass Impingers (AGI). Viable particles of SARS-CoV-2 were further characterised using the Collison 6-jet nebuliser in conjunction with novel sample techniques in an Andersen size-fractioning sampler to predict lung deposition profiles. Results demonstrate that all the tested nebulisers can generate stable, polydisperse aerosols (Geometric standard deviation (GSD) circa 1.8) in the respirable range (1.2 to 2.2 µm). Viable fractions (VF, units PFU/particle, the virus viability as a function of total particles produced) were circa 5 × 10^-3. VF and spray factors were not significantly affected by relative humidity, within this system where aerosols were in the spray tube an extremely short time. The novel Andersen sample collection methods successfully captured viable virus particles across all sizes; with most particle sizes below 3.3 µm. Particle sizes, in MMAD (Mass Median Aerodynamic Diameters), were calculated from linear regression of log₁₀-log₁₀ transformed cumulative PFU data, and calculated MMADs accorded well with APS measurements and did not differ across collection method types. These data will be vital in informing animal aerosol challenge models, and infection prevention and control policies.

Efficacy of Pre-Procedural Mouthwashes against SARS-CoV-2: A Systematic Review of Randomized Controlled Trials

The oral mucosa is one of the first sites to be affected by the SARS-CoV-2. For this reason, healthcare providers performing aerosol-generating procedures (AGPs) in the oral cavity are at high risk of infection with COVID-19. The aim of this systematic review is to verify whether there is evidence in the literature describing a decrease in the salivary viral load of SARS-CoV-2 after using different mouthwashes. An electronic search of the MEDLINE database (via PubMed), Web of Science, SCOPUS, and the Cochrane library database was carried out. The criteria used were those described by the PRISMA® Statement. Randomized controlled trial studies that have used mouthwashes as a form of intervention to reduce the viral load in saliva were included. The risk of bias was analyzed using the Joanna Briggs Institute Critical Appraisal Tool. Ultimately, eight articles were included that met the established criteria. Based on the evidence currently available in the literature, PVP-I, CHX and CPC present significant virucidal activity against SARS-CoV-2 in saliva and could be used as pre-procedural mouthwashes to reduce the risk of cross-infection.

Respiratory pandemic and indoor aeraulics of classrooms

Respiratory pandemics, such as COVID19, may be transmitted by several modes. The present work focuses on the transmission through small droplets released by people from their mouth by breathing, speaking, coughing, sneering, and possibly aspirated by other people around through their respiration. An analysis of droplet evolution in simplified situations shows that the droplets reach very quickly a quasi-equilibrium temperature before encompassing an isothermal evaporation process. The removal of droplets from suspension is thus piloted by balance between evaporation and sedimentation. It is shown that ambient relative humidity is a major factor influencing the lifetime of droplets and the distance they may travel. As a consequence, and independently of any other health consideration linked to ambient humidity, it is seen that a dry air is a favourable factor for limiting risk of contamination from COVID19. Further investigation is made using computational fluid dynamics (CFD) in a classroom geometry. Several ventilation strategies are investigated: classical regulatory mechanical ventilation, open window natural ventilation and displacement natural ventilation. Ventilation has several effects which influence contamination risk: by introducing fresh air, it reduces droplet concentration; humidity released by human occupants is also limited. However, these effects are not uniform in space, and depend on ventilation strategy. Application of a dose-effect model calibrated for COVID19 to CFD results allows to estimate contamination risk. It is shown that contamination risk is higher for regulatory mechanical ventilation, and may be reduced, using natural ventilation in the absence of wind, by a factor 2.3 to nearly 3 when the teacher is sick, and by a factor 6 to 500 when a student is sick. In the presence of wind, the reduction factor is as high as 13 when the teacher is sick and 17 when a student is sick.

Exposure Risk to Medical Staff in a Nasopharyngeal Swab Sampling Cabin under Four Different Ventilation Strategies

Medical staff working in a nasopharyngeal swab sampling cabin are exposed to a higher exposure risk of COVID-19. In this study, computational fluid dynamics (CFD) are used to evaluate the exposure risk to medical staff in a nasopharyngeal swab sampling cabin of Chinese customs under four different ventilation strategies, i.e., multiple supply fans ventilation (MSFV), multiple exhaust fans ventilation (MEFV), single exhaust fan and outer windows closed ventilation (SEFV), and single exhaust fan and outer windows opened ventilation (SEFV-W). The impact of physical partitions on exposure risk is also discussed. The results show that MSFV performed best in reducing exposure risk. No significant difference was found between MEFV and SEFV. SEFV-W performed better than SEFV with a ventilation rate of 10–50 L/(s∙Person), while it performed worse with a ventilation rate of 50–90 L/(s∙Person). The exposure risk to medical staff did not decrease linearly with the increase in the ventilation flow rate under the four ventilation strategies. For MSFV, the installation of partitions is conducive to the reduction in the exposure risk. This study is expected to provide some guidance for ventilation designs in sampling cabins.

A clinical observational analysis of aerosol emissions from dental procedures

Aerosol generating procedures (AGPs) are defined as any procedure releasing airborne particles <5 μm in size from the respiratory tract. There remains uncertainty about which dental procedures constitute AGPs. We quantified the aerosol number concentration generated during a range of periodontal, oral surgery and orthodontic procedures using an aerodynamic particle sizer, which measures aerosol number concentrations and size distribution across the 0.5-20 μm diameter size range. Measurements were conducted in an environment with a sufficiently low background to detect a patient's cough, enabling confident identification of aerosol. Phantom head control experiments for each procedure were performed under the same conditions as a comparison. Where aerosol was detected during a patient procedure, we assessed whether the size distribution could be explained by the non-salivary contaminated instrument source in the respective phantom head control procedure using a two-sided unpaired t-test (comparing the mode widths (log(σ)) and peak positions (DP,C)). The aerosol size distribution provided a robust fingerprint of aerosol emission from a source. 41 patients underwent fifteen different dental procedures. For nine procedures, no aerosol was detected above background. Where aerosol was detected, the percentage of procedure time that aerosol was observed above background ranged from 12.7% for ultrasonic scaling, to 42.9% for 3-in-1 air + water syringe. For ultrasonic scaling, 3-in-1 syringe use and surgical drilling, the aerosol size distribution matched the non-salivary contaminated instrument source, with no unexplained aerosol. High and slow speed drilling produced aerosol from patient procedures with different size distributions to those measured from the phantom head controls (mode widths log(σ)) and peaks (DP,C, p< 0.002) and, therefore, may pose a greater risk of salivary contamination. This study provides evidence for sources of aerosol generation during common dental procedures, enabling more informed evaluation of risk and appropriate mitigation strategies.

Virucidal Activity of Different Mouthwashes against the Salivary Load of SARS-CoV-2: A Narrative Review

The saliva of COVID-19-confirmed patients presents a high viral load of the virus. Aerosols generated during medical and dental procedures can transport the virus and are a possible causative agent of cross-infection. Since the onset of the pandemic, numerous investigations have been attempting to mitigate the risk of transmission by reducing the viral load in saliva using preprocedural mouthwashes. This study aims to review the most up-to-date in vitro and in vivo studies investigating the efficacy of different mouthwashes on reducing the salivary viral load of SARS-CoV-2, giving particular attention to the most recent randomized control trials published.

Viral load of SARS-CoV-2 in droplets and bioaerosols directly captured during breathing, speaking and coughing

Determining the viral load and infectivity of SARS-CoV-2 in macroscopic respiratory droplets, bioaerosols, and other bodily fluids and secretions is important for identifying transmission modes, assessing risks and informing public health guidelines. Here we show that viral load of SARS-CoV-2 Ribonucleic Acid (RNA) in participants' naso-pharyngeal (NP) swabs positively correlated with RNA viral load they emitted in both droplets >10 [Formula: see text] and bioaerosols <10 [Formula: see text] directly captured during the combined expiratory activities of breathing, speaking and coughing using a standardized protocol, although the NP swabs had [Formula: see text] 10[Formula: see text] more RNA on average. By identifying highly-infectious individuals (maximum of 18,000 PFU/mL in NP), we retrieved higher numbers of SARS-CoV-2 RNA gene copies in bioaerosol samples (maximum of 4.8[Formula: see text] gene copies/mL and minimum cycle threshold of 26.2) relative to other studies. However, all attempts to identify infectious virus in size-segregated droplets and bioaerosols were negative by plaque assay (0 of 58). This outcome is partly attributed to the insufficient amount of viral material in each sample (as indicated by SARS-CoV-2 gene copies) or may indicate no infectious virus was present in such samples, although other possible factors are identified.