Biodiesel production from heterotrophic microalgal oil

Microalgae to bioenergy production: Recent advances, influencing parameters, utilization of wastewater - A critical review

Fossil fuel limitations and their influence on climate change through atmospheric greenhouse gas emissions have made the excessive use of fossil fuels widely recognized as unsustainable. The high lipid content, carbon-neutral nature and potential as a biofuel source have made microalgae a subject of global study. Microalgae are a promising supply of biomass for third-generation biofuels production since they are renewable. They have the potential to produce significant amounts of biofuel and are considered a sustainable alternative to non-renewable energy sources. Microalgae are currently incapable to synthesize algal biofuel on an extensive basis in a sustainable manner, despite their significance in the global production of biofuels. Wastewater contains nutrients (both organic and inorganic) which is essential for the development of microalgae. Microalgae and wastewater can be combined to remediate waste effectively. Wastewater of various kinds such as industrial, agricultural, domestic, and municipal can be used as a substrate for microalgal growth. This process helps reduce carbon dioxide emissions and makes the production of biofuels more cost-effective. This critical review provides a detailed analysis of the utilization of wastewater as a growth medium for microalgal - biofuel production. The review also highlights potential future strategies to improve the commercial production of biofuels from microalgae.

Growth and Cell Size of Microalga Auxenochlorella protothecoides AS-1 under Different Trophic Modes

Certain microalgal species can grow with different trophic strategies depending on the availability of nutrient resources. They can use the energy from light or an organic substrate, or both, and can therefore be called autotrophs, heterotrophs, or mixotrophs. We recently isolated a microalgal strain from the microplastic biofilm, which was identified as Auxenochlorella protothecoides, AS-1. Strain AS-1 grew rapidly in bacterial culture media and exhibited different growth rates and cell sizes under different trophic conditions. We compared the growth performance of AS-1 under the three different trophic modes. AS-1 reached a high biomass (>4 g/L) in 6 days under mixotrophic growth conditions with a few organic carbons as a substrate. In contrast, poor autotrophic growth was observed for AS-1. Different cell sizes, including daughter and mother cells, were observed under the different growth modes. We applied a Coulter Counter to measure the size distribution patterns of AS-1 under different trophic modes. We showed that the cell size distribution of AS-1 was affected by different growth modes. Compared to the auto-, hetero- and mixotrophic modes, AS-1 achieved higher biomass productivity by increasing cell number and cell size in the presence of organic substrate. The mechanisms and advantages of having more mother cells with organic substrates are still unclear and warrant further investigations. The work here provides the growth information of a newly isolated A. protothecoides AS-1 which will be beneficial to future downstream applications.

Bioenergy relations with agriculture, forestry and other land uses: Highlighting the specific contributions of artificial intelligence and co-citation networks

The concerns with the environment and sustainability have promoted options for energy sources that mitigate the footprint of human life. The use of biomass from agriculture, forestry and other land uses (AFOLU) has enormous potential for the production of bioenergy as a renewable source of energy. In this context, this research aims to analyse the interrelationships between bioenergy and agriculture, forestry and other land uses, highlighting the contributions of the digital transition for these dimensions. To achieve these objectives, a bibliometric analysis through co-citation links (and items related to cited authors, references and sources) was carried out for the dimensions associated with the bioenergy and the AFOLU and after a specific literature survey was performed for the contributions from the digital transition for these frameworks. With this study, top authors, references and sources were identified for the topics assessed and it was highlighted the importance of digital transitions for more efficient bioenergy use and production in the worldwide contexts.

Proteinaceous Microsphere-Based Water-in-Oil Pickering Emulsions for Preservation of Chlorella Cells

Microalgae are highly regarded as ideal materials for the creation of liquid biofuels and have substantial potential for growth and utilization. However, traditional storage and culture methods for microalgae are plagued by challenges such as uncontrolled growth, bacterial contamination, and self-shading among algae. These issues severely impede the photosynthetic process and the efficient extraction of biomass energy. This study tackles these problems by utilizing magnetic hydrophobic protein particles to stabilize water-in-oil Pickering emulsions. This allows for the micro-compartment storage and magnetic transfer of algae. Additionally, the successful encapsulation of Chlorella cells in high-internal-phase water-in-oil Pickering emulsions effectively mitigates the settling problem of Chlorella cells in the liquid phase, thereby enabling the potential use of Pickering emulsions for the confined cultivation of microalgae.

Life cycle assessment of integrated microalgae oil production in Bojongsoang Wastewater Treatment Plant, Indonesia

This study aims to determine the eco-friendliness of microalgae-based renewable energy production in several scenarios based on life cycle assessment (LCA). The LCA provides critical data for sustainable decision-making and energy requirement analysis, including net energy ratio (NER) and cumulative energy demand (CED). The Centrum voor Milieuwetenschappen Leiden (CML) IA-Baseline was used on environmental impact assessment method by SimaPro v9.3.0.3® software and energy analysis of biofuel production using native polyculture microalgae biomass in municipal wastewater treatment plants (WWTP) Bojongsoang, Bandung, Indonesia. The study was analyzed under three scenarios: (1) the current scenario; (2) the algae scenario without waste heat and carbon dioxide (CO2); and (3) the algae scenario with waste heat and carbon dioxide (CO2). Waste heat and CO2 were obtained from an industrial zone near the WWTP. The results disclosed that the microalgae scenario with waste heat and CO2 utilization is the most promising scenario with the lowest environmental impact (- 0.139 kg CO2eq/MJ), positive energy balance of 1.23 MJ/m3 wastewater (NER > 1), and lower CED value across various impact categories. It indicates that utilizing the waste heat and CO2 has a positive impact on energy efficiency. Based on the environmental impact, NER and CED values, this study suggests that the microalgae scenario with waste heat and CO2 is more feasible and sustainable to adopt and could be implemented at the Bojongsoang WWTP.

Trends on Chlamydomonas reinhardtii growth regimes and bioproducts

The green microalga Chlamydomonas reinhardtii is a model microorganism for several areas of study. Among the different microalgae species, it presents advantageous characteristics, such as genomes completely sequenced and well-established techniques for genetic transformation. Despite that, C. reinhardtii production is still not easily commercially viable, especially due to the low biomass yield. So far there are no reports of scientometric study focusing only on C. reinhardtii biomass production process. Considering the need for culture optimization, a scientometric research was conducted to analyze the papers that investigated the growth regimes effects in C. reinhardtii cultivation. The search resulted in 130 papers indexed on Web of Science and Scopus platforms from 1969 to December 2022. The quantitative analysis indicated that the photoautotrophic regime was the most employed in the papers. However, when comparing the three growth regimes, the mixotrophic one led to the highest production of biomass, lipids, and heterologous protein. The production of bioproducts was considered the main objective of most of the papers and, among them, biomass was the most frequently investigated. The highest biomass production reported among the papers was 40 g L-1 in the heterotrophic growth of a transgenic strain. Other culture conditions were also crucial for C. reinhardtii growth, for instance, temperature and cultivation process.

Isotope-labeling in situ derivatization and HS-SPME arrow GC-MS/MS for simultaneous determination of fatty acids and fatty acid methyl esters in aqueous matrices

Fatty acids (FAs) and fatty acid methyl esters (FAMEs) co-occur in many samples, and analysis of both substance classes is frequently of high interest. To this end, this study introduces the first method for simultaneous determination of FAs and FAMEs including fully automated solvent-free solid-phase microextraction (SPME) arrow headspace extraction combined with isotope-labeling in situ FA derivatization with deuterated methanol (CD3OD). By using the chromatographic isotope effect (ΔRt = 0.03 min) and the + 3 m/z mass shift, FAs can be selectively differentiated from the FAMEs during gas chromatography tandem-mass spectrometry (GC-MS/MS) operated in the multiple reaction monitoring (MRM) aquisition mode. Additionally, an approach is presented to predict the retention times of deuterated compounds. Optimization of the derivatization conditions was accomplished by design of experiments and found to be 20 min, 50 °C, 4 v/v% CD3OD, and pH 2.1. During method validation, FAs and FAMEs were calibrated in different concentration ranges by standard addition in five real matrices and ultrapure water leading to good linearities and method detection limits for FAs ranging from 1-30 µg L-1 and for FAMEs from 0.003-0.72 µg L-1. FAs and FAMEs were detected in real samples from surface water, wastewater treatment plant effluent, and three different bioreactor samples and could be quantified in concentrations ranging from 2-1056 µg L-1 for FAs and 0.01-14 µg L-1 for FAMEs.

Identification and Characterization of a Novel Microalgal Strain from the Antofagasta Coast Tetraselmis marina AC16-MESO (Chlorophyta) for Biotechnological Applications

The wide rocky coastline of the Antofagasta hosts an intertidal ecosystem in which the species that inhabit it are routinely exposed to a wide range of physical and chemical conditions and have therefore evolved to tolerate extremes. In the search for new species of potential biotechnological interest with adaptations to a wide range of environmental conditions, the isolation and characterization of microalgae from these ecosystems is of great interest. Here, a new microalgal strain, Tetraselmis marina AC16-MESO, is described, which was isolated from a biofilm collected on the intertidal rocks of the Antofagasta coast (23°36'57.2″ S, 70°23'33.8″ W). In addition to the morphological characterization, 18S and ITS sequence as well as ITS-2 secondary structure analysis revealed an identity of 99.76% and 100% with the species Tetraselmis marina, respectively. The analyses of the culture characteristics and biochemical content showed similarities with other strains that are frequently used in aquaculture, such as the species Tetraselmis suecica. In addition, it is tolerant of a wide range of salinities, thus allowing its culture in water of varying quality. On the other hand, added to these characteristics, the results of the improvement of the lipid content in stressful situations of salinity observed in this study, together with other antecedents such as the potential in bioremediation already published for this strain by the same research group, present a clear example of its biotechnological plasticity. It is noteworthy that this strain, due to its characteristics, allows easy collection of its biomass by decantation and, therefore, a more cost-efficient harvesting than for other microalgal strains. Therefore, this new strain of Tetraselmis marina, first report of this species in Chile, and its morphologically, molecularly and biochemically description, presents promising characteristics for its use in biotechnology and as feed for aquaculture.

Biodiesel production from Sisymbrium irio as a potential novel biomass waste feedstock using homemade titania catalyst

Biomass waste streams are a possible feedstock for a range of eco-friendly products and a crucial alternative energy source for achieving carbon neutrality; therefore, the efficient management of biomass waste has taken on a greater significance in recent years. Due to its well-comparable physic-chemical properties with fossil diesel, biodiesel is a potential substitute for fossil fuel. This study aimed to synthesize biodiesel from the widely available non-edible seed oil of Sisymbrium irio L. (a member of the Brassicaceae family) via a transesterification procedure over a homemade TiO2 catalyst. At 1:16 oil to methanol ratio, 93% biodiesel yield was obtained over 20 mg catalyst at 60 °C and 60 min. The ASTM methods were used to analyze the fuel properties. The quantitative and qualitative analysis was performed by FT-IR, GC-MS, and NMR spectroscopy. GC-MS study confirms 16 different types of fatty acids of methyl esters. FT-IR analysis showed important peaks that confirm the successful occurrence of biodiesel. 1H-NMR and 13C-NMR showed important peaks for converting triglycerides into corresponding FAMEs. The acid value (0.42 mg KOH/mg/kg), flash point (106 °C), and water content (0.034) of biodiesel are below the specified limit of ASTM D6751 whereas kinetic viscosity (3.72 mm2/s), density (0.874 kg/L), cloud point (- 4.3 °C) and pour point (- 9.6 °C) and high heating value (41.62 MJ/kg) fall within the specified range of ASTM D6751 test limit. The Unsaturation degree and oxidative stability of biodiesel are above ASTM D6751 test limit. The physic-chemical properties of the SIB confirm that it is eco-friendly fuel and a competitive source for manufacturing biodiesel on a commercial scale. Furthermore, the SIB is engine friendly and has good fuel efficacy.

Effects of Lead and Zinc Exposure on Uptake and Exudation Levels, Chlorophyll-a, and Phycobiliproteins in Sarcodia suiae

The present study aimed to determine the changes in the biosorption, bioaccumulation, chlorophyll-a (chl-a), phycobiliproteins, and exudation in the red seaweed Sarcodia suiae exposed to lead and zinc. The seaweed was exposed to ambient lead and zinc environments for 5 days before being transferred to fresh seawater, and the changes in biodesorption, biodecumulation, chl-a, and phycobiliprotein levels in S. suiae were investigated. Lead and zinc biosorption and bioaccumulation in the seaweed increased with the increase in the lead and zinc concentrations and exposure times. Meanwhile, the biosorption and bioaccumulation of zinc in the seaweed following exposure to zinc were significantly higher (p < 0.05) than the biosorption and bioaccumulation of lead in the seaweed following exposure to lead with the same concentration at each exposure time. The chl-a, phycoerythrin (PE), phycocyanin (PC), and allophycocyanin (APC) contents in the seaweed significantly decreased with the increase in the lead and zinc concentrations and exposure times. The chl-a, PE, PC, and APC contents in S. suiae, which was exposed to 5 Pb2+ mg/L for 5 days, were significantly higher (p < 0.05) than those in the seaweed exposed to zinc at the same concentration and for the same exposure times. In the lead and zinc exudation tests, the highest biodesorption and biodecumulation were observed on the 1st day of exudation after the seaweed was transferred to fresh seawater. The residual percentages of the lead and zinc in the seaweed cells were 15.86% and 73.08% after 5 days of exudation, respectively. The biodesorption rate and biodecumulation rate of the seaweed exposed to lead were higher than those of the seaweed exposed to zinc. However, the effect of lead on chl-a and phycobiliproteins was greater than that of zinc. This might be the result of lead not being a necessary metal for these algae, whereas zinc is.

Photothermal technique-enabled ambient production of microalgae biodiesel: Mechanism and life cycle assessment

Thermocatalytic (trans)esterification of oils/lipids to produce biodiesel is generally energy-consuming, reversible, and controlled by the equilibrium law. Herein, a light-induced photothermal process was illustrated to be highly efficient for biodiesel production (96.8 % yield) from microalgae lipids at room temperature enabled by a biomass-based SO₃H-functionalized graphene-like heterogeneous catalyst (S-NGL-600), as optimized by response surface methodology. Infrared thermal imaging indicated that interfacial solar heating led to forming a local photothermal catalytic system, reaching 72.2 °C in 2 min. The local light heating was conducive to evaporation and removal of water from acid sites, resulting in local excess of microalgae lipids to facilitate the forward reaction. Notably, the photothermal catalyst was highly recyclable and exhibited a significantly higher conversion rate of microalgae lipids than industrially used catalyst H₂SO₄. Life cycle assessment suggested energy-saving advantage (0.87 MJ/MJ) and environmental protection (-89.42 CO_2eq/MJ) of the photothermal-driven protocol for microalgae biodiesel production.

Clustered regularly interspaced short palindromic repeats (CRISPR) technology and genetic engineering strategies for microalgae towards carbon neutrality: A critical review

Carbon dioxide is the major greenhouse gas and regards as the critical issue of global warming and climate changes. The inconspicuous microalgae are responsible for 40% of carbon fixation among all photosynthetic plants along with a higher photosynthetic efficiency and convert the carbon into lipids, protein, pigments, and bioactive compounds. Genetic approach and metabolic engineering are applied to accelerate the growth rate and biomass of microalgae, hence achieve the mission of carbon neutrality. Meanwhile, CRISPR/Cas9 is efficiently to enhance the productivity of high-value compounds in microalgae for it is easier operation, more affordable and is able to regulate multiple genes simultaneously. The genetic engineering strategies provide the multidisciplinary concept to evolute and increase the CO₂ fixation rate through Calvin-Benson-Bassham cycle. Therefore, the technologies, bioinformatics tools, systematic engineering approaches for carbon neutrality and circular economy are summarized and leading one step closer to the decarbonization society in this review.

Insight into the comprehensive effect of carbon dioxide, light intensity and glucose on heterotrophic-assisted phototrophic microalgae biofilm growth: A multifactorial kinetic model

Heterotrophic-assisted photoautotrophic microalgae biofilm cultivation was an alternative way to realize CO₂ reduction and wastewater treatment. Growth kinetics supplied a channel to better understand how the cultivation conditions affect microalgal growth and CO₂ reduction. However, the two growth modes (heterotroph and photoautotroph) have different needs for organic and inorganic nutrients. Thus, combining the threshold theory and multiplication theory, an integral multifactorial kinetic model that looking insight into the comprehensive effect of glucose, CO₂, light intensity, and nitrate was developed for heterotrophic-assisted photoautotrophic microalgae biofilm growth in this study. R² between model and experiment was 0.99. It predicted the maximum specific growth rate and maximum CO₂ consumption rate of heterotrophic-assisted photoautotrophic microalgae biofilm was 1.868 h^-1 and 1.02 h^-1, respectively. This model fully explained the influence of the main factors on microalgae biofilm growth and reasonably predicted the growth rate of microalgae biofilm under different growth conditions.

Biocoagulation of Dried Algae Chlorella sp. and Pellets of Aspergillus Niger in Decontamination Process of Wastewater, as a Presumed Source of Biofuel

The removal of microalgae represents a problematic part of the water decontamination process, in which most techniques are expensive and non-ecological. In the paper, we focus on the synergistic relationship between microscopic filamentous fungi and algal culture. In the process of decontamination of a model sample containing ammonium ions, efficient biocoagulation, resp. co-pelletization of dried algae Chlorella sp. and Aspergillus niger sensu stricto are shown. The microscopic filamentous fungus species A. niger was added to a culture of an algal suspension of Chlorella sp., where the adhesion of the algal cells to the fungi subsequently occurred due to the electrostatic effect of the interaction, while the flocculation activity was approximately 70 to 80%. The algal cells adhered to the surface of the A. niger pellets, making them easily removable from the solution. The ability of filamentous fungi to capture organisms represents a great potential for the biological isolation of microalgae (biocoagulation) from production solutions because microalgae are considered to be a promising renewable source of oil and fermentables for bioenergy. This form of algae removal, or its harvesting, also represents a great low-cost method for collecting algae not only as a way of removing unnecessary material but also for the purpose of producing biofuels. Algae are a robust bioabsorbent for absorbing lipids from the environment, which after treatment can be used as a component of biodiesel. Chemical analyses also presented potential ecological innovation in the area of biofuel production. Energy-efficient and eco-friendly harvesting techniques are crucial to improving the economic viability of algal biofuel production.

Simultaneous bioremediation of Disperse orange-2RL Azo dye and fatty acids production by Scenedesmus obliquus cultured under mixotrophic and heterotrophic conditions

Several types of green photosynthetic microalgae can grow through the process of heterotrophic growth in the dark with the help of a carbon source instead of the usual light energy. Heterotrophic growth overcomes important limitations in the production of valuable products from microalgae, such as the reliance on light, which complicates the process, raises costs, and lowers the yield of potentially useful products. The present study was conducted to explore the potential growth of green microalga Scenedesmus obliquus under mixotrophic and heterotrophic conditions utilizing Disperse orange 2RL Azo dye as a carbon source to produce a high lipid content and the maximum dye removal percentage. After 7 days of algal growth with dye under mixotrophic and heterotrophic conditions with varying pH levels (5, 7, 9, and 11), KNO₃ concentrations (1, 1.5, 2, and 3 g/L), and dye concentrations (20, 40, and 60 ppm); dye removal percentage, algal dry weight, and lipid content were determined. The results showed that the highest decolorization of Disperse orange 2RL Azo dye (98.14%) was attained by S. obliquus in heterotrophic medium supplemented with glucose at the optimal pH 11 when the nitrogen concentration was 1 g/L and the dye concentration was 20 ppm. FT-IR spectroscopy of the dye revealed differences in peaks position and intensity before and after algal treatment. S. obliquus has a high concentration of oleic acid, which is enhanced when it is grown with Disperse orange 2RL Azo dye, making it ideal for production of high-quality biodiesel. In general, and in the vast majority of instances, heterotrophic cultivation is substantially less expensive, easier to set up, and requires less maintenance than mixotrophic cultivation. Heterotrophic cultivation allows for large-scale applications such as separate or mixed wastewater treatment along with biofuel production.

Microalgae cultivation strategies using cost-effective nutrient sources: Recent updates and progress towards biofuel production

Scientists are grabbing huge attention as well as consciousness on non-renewable energy sources for the global energy crises because of gradual increase in oil price, fast depletion or low availability of resources, and the release of more toxic-gases (CO₂, SO_x, N_xO) during exhaustion, etc. Due to such hitches, the key need is to find alternative biofuels or feedstocks to replace fossil fuel energy demands worldwide. Currently, microalgae have become intrigued feedstock candidates (3rd generation source of biofuel) to replace nearly 50-60 % of fossil fuels due to high production of biomass and oil, mitigating CO₂ and wastewater remediation. The present work demonstrated the current developments and future perspectives on large-scale algal cultivation strategies for the biorefinery economy. In addition, various advanced cultivation techniques adopted for enhanced biomass production and cost-effective methods for bioenergy production were detailly discussed.

Production of Biodiesel from Underutilized Algae Oil: Prospects and Current Challenges Encountered in Developing Countries

Simple Summary

The production of biofuel, especially biodiesel, from algae oil receives little attention in developing countries due to poor enlightenment on biotechnology, high poverty rates, and poor funding of research. This study focuses on finding a better understanding of the evolving prospects and current challenges facing biodiesel production from algae oil in developing nations. Interestingly, several species of microalgae that can serves as sustainable feedstocks for biodiesel production have been identified in developing nations. It is evident that microalgae oil has physicochemical properties that qualifies it for the production of biodiesel, with fuel properties that meet ASTM and EN standards.

Abstract

Biofuel continues to thrive as an outstanding source of renewable energy for the global community. Several resources have been proposed as sources of feedstocks for biofuel; however, some of these have shortcoming. The use of biomass such as algae as a source of feedstock for biofuel is undoubtedly sustainable and green. Unfortunately, the use of algae oil for biodiesel production is underutilized in developing countries. Therefore, this study focuses on finding a better understanding of the evolving prospects and current challenges facing biodiesel production from algae oil in developing countries. The study revealed that less attention is given to the use of algae oil in biodiesel production due to poor enlightenment on biotechnology, high poverty rates, government policies, business strategies, and poor funding of research. Interestingly, several species of algae that can serve as sustainable feedstocks for biodiesel production have been identified in developing countries. It is evident that algae oil has properties that qualify it for the production of biodiesel with fuel properties that meet both the American Society for Testing and Materials and the European standards for biodiesel.

Technoeconomic Evaluation of Microalgae Oil Production: Effect of Cell Disruption Method

Microalgae have a high capacity to capture CO2. Additionally, biomass contains lipids that can be used to produce biofuels, biolubricants, and other compounds of commercial interest. This study analyzed various scenarios for microalgae lipid production by simulation. These scenarios include cultivation in raceway ponds, primary harvest with three flocculants, secondary harvest with pressure filter (and drying if necessary), and three different technologies for the cell disruption step, which facilitates lipid extraction. The impact on energy consumption and production cost was analyzed. Both energy consumption and operating cost are higher in the scenarios that consider bead milling (8.79–8.88 kWh/kg and USD 41.06–41.41/kg), followed by those that consider high-pressure homogenization (HPH, 5.39–5.46 kWh/kg and USD 34.26–34.71/kg). For the scenarios that consider pressing, the energy consumption is 5.80–5.88 kWh/kg and the operating cost is USD 27.27–27.88/kg. The consumption of CO2 in scenarios that consider pressing have a greater capture (11.23 kg of CO2/kg of lipids). Meanwhile, scenarios that consider HPH are the lowest consumers of fresh water (5.3 m3 of water/kg of lipids). This study allowed us to develop a base of multiple comparative scenarios, evaluate different aspects involved in Chlorella vulgaris lipid production, and determine the impact of various technologies in the cell disruption stage.

Low Indirect Land Use Change (ILUC) Energy Crops to Bioenergy and Biofuels—A Review

Energy crops are dedicated cultures directed for biofuels, electricity, and heat production. Due to their tolerance to contaminated lands, they can alleviate and remediate land pollution by the disposal of toxic elements and polymetallic agents. Moreover, these crops are suitable to be exploited in marginal soils (e.g., saline), and, therefore, the risk of land-use conflicts due to competition for food, feed, and fuel is reduced, contributing positively to economic growth, and bringing additional revenue to landowners. Therefore, further study and investment in R&D is required to link energy crops to the implementation of biorefineries. The main objective of this study is to present a review of the potential of selected energy crops for bioenergy and biofuels production, when cultivated in marginal/degraded/contaminated (MDC) soils (not competing with agriculture), contributing to avoiding Indirect Land Use Change (ILUC) burdens. The selected energy crops are Cynara cardunculus, Arundo donax, Cannabis sativa, Helianthus tuberosus, Linum usitatissimum, Miscanthus × giganteus, Sorghum bicolor, Panicum virgatum, Acacia dealbata, Pinus pinaster, Paulownia tomentosa, Populus alba, Populus nigra, Salix viminalis, and microalgae cultures. This article is useful for researchers or entrepreneurs who want to know what kind of crops can produce which biofuels in MDC soils.

Production and Functionalities of Specialized Metabolites from Different Organic Sources

Medicinal plants are rich sources of specialized metabolites that are of great importance to plants, animals, and humans. The usefulness of active biological compounds cuts across different fields, such as agriculture, forestry, food processing and packaging, biofuels, biocatalysts, and environmental remediation. In recent years, research has shifted toward the use of microbes, especially endophytes (bacteria, fungi, and viruses), and the combination of these organisms with other alternatives to optimize the production and regulation of these compounds. This review reinforces the production of specialized metabolites, especially by plants and microorganisms, and the effectiveness of microorganisms in increasing the production/concentration of these compounds in plants. The study also highlights the functions of these compounds in plants and their applications in various fields. New research areas that should be explored to produce and regulate these compounds, especially in plants and microbes, have been identified. Methods involving molecular studies are yet to be fully explored, and next-generation sequencing possesses an interesting and reliable approach.

Recovery of value-added products by mining microalgae

Microalgae blooms are always blamed for the interruption of the aquatic environment and pose a risk to the source of drinking water. Meanwhile, microalgae as primary producers are a kind of resource pool and could benefit the environment and contribute to building a circular economy. The lipid and polyhydroxybutyrate (PHB) in the cells of microalgae could be alternatives to fossil fuels and plastics, respectively, which are the culprits of global warming and plastic pollution. Besides, some microalgae are rich in nutrients, such as proteins and astaxanthin, which make themselves suitable for feed additives. As wastewater is rich in nutrients necessary for microalgae, thus, value-added product recovery via microalgae could be an approach to valorizing wastewater. However, a one-size-fits-all approach deploying various wastewater for the above products cannot be summarized. On the contrary, specific technical protocols should be tailored regarding each product in microalgae biomass with various wastewater. Thus, this review is to summarize the research effort by far on wastewater-cultivated microalgae for value-added products. Wastewater type, regulation methods, and targeted product yields are compiled and discussed and are expected to guide future extrapolation into a commercial scale.

Life Span of Slippery Lubricant Infused Surfaces

Since their discovery a decade ago, slippery liquid infused porous surfaces (SLIPSs) or lubricant infused surfaces (LISs) have been demonstrated time and again to have immense potential for a plethora of applications. Of these, one of the most promising is enhancing the energy efficiency of both thermoelectric and organic Rankine cycle power generation via enhanced vapor condensation. However, utilization of SLIPSs in the energy sector remains limited due to the poor understanding of their life span. Here, we use controlled conditions to conduct multimonth steam and ethanol condensation tests on ultrascalable nanostructured copper oxide structured surfaces impregnated with mineral and fluorinated lubricants having differing viscosities (9.7 mPa·s < μ < 5216 mPa·s) and chemical structures. Our study demonstrates that SLIPSs lose their hydrophobicity during steam condensation after 1 month due to condensate cloaking. However, these same SLIPSs maintain nonwetting after 5 months of ethanol condensation due to the absence of cloaking. Surfaces impregnated with higher viscosity oil (5216 mPa·s) increase the life span to more than 8 months of continuous ethanol condensation. Vapor shear tests revealed that SLIPSs do not undergo oil depletion during exposure to 10 m/s gas flows, critical to condenser implementation where single-phase superheated vapor impingement is prevalent. Furthermore, higher viscosity SLIPSs are shown to maintain good stability after exposure to 200 °C air. A subset of the durable SLIPSs did not show change in slipperiness after submerging in stagnant water and ethanol for up to 2 weeks, critical to condenser implementation where single-phase condensate immersion is prevalent. Our work not only demonstrates design methods and longevity statistics for slippery nanoengineered surfaces undergoing long-term dropwise condensation of steam and ethanol but also develops the fundamental design guidelines for creating durable slippery liquid infused surfaces.

Comprehensive Techno-Economic Analysis of a Multi-Feedstock Biorefinery Plant in Oil-Rich Country: A Case Study of Iran

The high energy consumption in Iran, particularly in the transportation sector, has contaminated large cities and jeopardized the society health. Therefore, in this study technical and economic features of the production of biodiesel plant in Iran from various wastes are investigated. Based on the Analytic Hierarchy Process (AHP) method’s findings, the southern area of Iran is selected for establishing the biodiesel plant in Iran. The biorefinery, which includes three units of sewage sludge, edible waste oil and microalgae. The results of the economic evaluation show that the lowest costs of investment and production of biodiesel are related to microalgae units ($0.375/kg) and edible waste oil ($0.53/kg), respectively. Also, among all units, the lowest break even prices are related to biodiesel production ($1.17/kg) and the highest ATROR rate (29.16%) belongs to the microalgae unit. This indicates that this unit is more profitable than other units and the invested cost is returned to the investor in a shorter period of time (3.43 years). On the other hand, the results of sensitivity analysis show that the highest sensitivity of changes in the selling price of biodiesel and the cost of raw materials to ATROR to the microalgae and sludge unit. Therefore, the construction of a biorefinery in Iran has an economic justification.

Microalgae role in sustainable bioenergy generation as determined by light microscopy

The main aim of this study was to explore the role of light microscopy in the identification of microalgae as a source of study. Three microalgal species (Nostoc, Anabaena, and Volvox) were identified by light. In this study, different parameters of the oil extraction process from algae biomass were studied. The samples of Nostoc, Anabaena, and Volvox were collected from the freshwater bodies in Lahore, and the samples were identified by light microscopy. Pretreatment of algae was done which includes harvesting, drying, and grinding. The sun drying of sample was done. Solvent extraction was done for the extraction of oil from algal cells. Solvent n-hexane and diethyl ether were used alone as well as in combination. Effects of n-hexane to oil ratio, size of algal biomass, and contact time on the percentage yield of extracted oil were studied and analyzed. It was concluded that maximum amount of oil was extracted from algae by using a greater ratio of solvent to algal biomass, maximum contact time, and smaller algal biomass size. The extracted oil yield was satisfactory, demonstrating the potential of microalgae for biodiesel production. It was discovered that if algal oil is subjected to transesterification, it can be turned into biodiesel, and light microscopy can be used to assess anatomical characteristics. However, more research will be required for transesterification.

Microalgal secondary metabolite productions as a component of biorefinery: A review

The interest in developing microalgae for industrial use has been increasing because of concerns about the depletion of petroleum resources and securing sustainable energy sources. Microalgae have high biomass productivity and short culture periods. However, despite these advantages, various barriers need to be overcome for industrial applications. Microalgal cultivation has a high unit price, thus rendering industrial application difficult. It is indispensably necessary to co-produce their primary and secondary metabolites to compensate for these shortcomings. In this regard, this article reviews the following aspects, (1) co-production of primary and secondary metabolites in microalgae, (2) induction methods for the promotion of the biosynthesis of secondary metabolites, and (3) perspectives on the co-production and co-extraction of primary and secondary metabolites. This paper presents various approaches for producing useful metabolites from microalgae and suggests strategies that can be utilized for the co-production of primary and secondary metabolites.

Recent advances in biodiesel production: Challenges and solutions

Mono alkyl fatty acid ester or methyl ethyl esters (biodiesel) are the promising alternative for fossil fuel or petroleum derived diesel with similar properties and could reduce the carbon foot print and the greenhouse gas emissions. Biodiesel can be produced from renewable and sustainable feedstocks like plant derived oils, and it is biodegradable and non-toxic to the ecosystem. The process for the biodiesel production is either through traditional chemical catalysts (Acid or Alkali Transesterification) or enzyme mediated transesterification, but as enzymes are natural catalysts with environmentally friendly working conditions, the process with enzymes are proposed to overcome the drawbacks of chemical synthesis. At present 95% of the biodiesel production is contributed by edible oils worldwide whereas recycled oils and animal fats contribute 10% and 6% respectively. Although every process has its own limitations, the enzyme efficiency, resistance to alcohols, and recovery rate are the crucial factors to be addressed. Without any benefit of doubt, production of biodiesel using renewable feedstocks and enzymes as the catalysts could be recommended for the commercial purpose, but further research on improving the efficiency could be an advantage.

An approach for dairy wastewater remediation using mixture of microalgae and biodiesel production for sustainable transportation

The aim of this work is remediation of dairy wastewater (DWW) for biodiesel feedstock production using poly-microalgae cultures of four microalgae namely Chlorella minutissima (C. minutissima), Scenedesmus abundans (S. abundans), Nostoc muscorum (N. muscorum) and Spirulina sp. The poly-microalgae cultures were prepared as C. minutissima + N. muscorum (CN), C. minutissima + N. muscorum + Spirulina sp. (CNSS) and S. abundans + N. muscorum + Spirulina sp. (SNSS). Poly-microalgae culture CNSS cultivated on 70% DWW achieved 75.16, 61.37, 58.76, 84.48 and 84.58%, removals of biological oxygen demand (BOD), chemical oxygen demand (COD), total nitrogen (TN), total phosphorus (TP), and suspended solids (SS), respectively, at 12:12 h photoperiod that resulted into total biomass and lipid yield of 3.47 ± 0.07 g/L and 496.32± 0.065 mg/L. However, maximum biomass and lipid yields of 5.76 ± 0.06 and 1152.37 ± 0.065 mg/L were achieved by poly-microalgae culture CNSS cultivated on 70% DWW + 10 g/L of glucose at 18:6 h photoperiod. Fatty acid methyl ester (FAME) analysis shown presence of C14:0 (myristic acid) C16:0 (palmitic acid), C16:1 (palmitoleic acid), C18:0 (stearic acid), C18:2 (linoleic acid) and C18:3 (linolenic acid), it indicates that the lipids produced from poly-microalgae cultures are suitable for biodiesel production. Thus, poly-microalgae cultures could be more efficient than mono-microalgae cultures in the remediation of DWW and for biodiesel feedstock production.

Insights into the genetic and metabolic engineering approaches to enhance the competence of microalgae as biofuel resource: A review

Conventional fuel resources are overburden with speedy global energy demand which ensued the urgent need of alternate energy resources. Biofuel generation efficiency of microalgae is notable due to their comparatively rapid biomass production rate and high oil content. But, the employment of microalgae as biofuel resource is in infancy due to low productivity and high production cost. The issues can be addressed by employing engineered microalgal strains that would be able to efficiently generate enhanced levels of biomass with augmented lipid and/or carbohydrate content for proficient biofuel production. Genetic alterations and metabolic engineering of microalgal species might be helpful in developing high stress-tolerant strains with improved properties for biofuel generation. Various omics approaches appeared significant to upgrade the microalgal lipid production. Intervention of genetic and metabolic engineering approaches would facilitate the development of microalgae as a competent biofuel resource and inflate the economic commercialization of biofuels.

Mixotrophic cultivation of microalgae coupled with anaerobic hydrolysis for sustainable treatment of municipal wastewater in a hybrid system of anaerobic membrane bioreactor and membrane photobioreactor

This study investigated the possibility of coupling anaerobic hydrolysis in an anaerobic membrane bioreactor (AnMBR) with mixotrophic microalgae cultivation in a membrane photobioreactor (MPBR) for the sustainable treatment of municipal wastewater. Using the hydrolyzed wastewater discharged from AnMBR, Chlorella pyrenoidosa in MPBR grew in a mixotrophic mode and realized rapid growth. During the stable operation, MPBR achieved average carbon capture rate of 42.82 mg L^-1 d^-1 and algal lipid production rate of 19.66 mg L^-1 d^-1. The average reduction in TN, TP, and TOC during stable operation was 96.7%, 98.0%, and 95.9%, respectively. Mass balance analysis showed that the overall system captured 14.76 mg of carbon from the atmosphere per liter of wastewater treated. Therefore, this AnMBR-MPBR hybrid system simultaneously realized advanced treatment of municipal wastewater, efficient production of algal lipid, and carbon capture from atmosphere, and thus has a good potential in the sustainable treatment of municipal wastewater.

The Catalysed Transformation of Vegetable Oils or Animal Fats to Biofuels and Bio-Lubricants: A Review

This review paper summarizes the current state-of-the-art of the chemical transformation of oils/fats (i.e., triacylglycerols) to the use of biofuels or bio-lubricants in the means of transport, which is a novelty. The chemical transformation is necessary to obtain products that are more usable with properties corresponding to fuels synthesized from crude oil. Two types of fuels are described—biodiesel (the mixture of methyl esters produced by transesterification) and green diesel (paraffins produced by hydrogenation of oils). Moreover, three bio-lubricant synthesis methods are described. The transformation, which is usually catalysed, depends on: (i) the type and composition of the raw material, including alcohols for biodiesel production and hydrogen for green diesel; (ii) the type of the catalyst in the case of catalysed reactions; (iii) the reaction conditions; and (iv) types of final products. The most important catalysts, especially heterogeneous and including reaction conditions, for each product are described. The properties of biodiesel and green diesel and a comparison with diesel from crude oil are also discussed.

The conundrum of waste cooking oil: Transforming hazard into energy

Waste cooking oil (WCO) is considered as one of the hazardous wastes because improper disposal of WCO can cause significant environmental problems such as blockages of drains and sewers as well as water or soil pollution. In this review, the physical and chemical properties of WCO are evaluated along with its regulations and policies in different countries to promote WCO refined biofuels. Blended WCO can be an auxiliary fuel for municipal solid waste incinerators while the heat produced is able to form superheated steam and subsequently generate electricity via combined heat and power system. Also, WCO contains high ratio of hydrogen atoms compared to carbon and oxygen atoms, making it able to be catalytically cracked, synthesizing hydrogen gas. WCO-based biodiesel has been traditionally produced by transesterification in order to substitute petroleum-based diesel which has non-degradability as well as non-renewable features. Hence, the potentials of hazardous WCO as a green alternative energy source for electricity generation, hydrogen gas as well as biofuels production (e.g. biodiesel, biogas, biojet fuel) are critically discussed due to its attractive psychochemical properties as well as its economic feasibility. Challenges of the WCO utilization as a source of energy are also reported while highlighting its future prospects.

Membrane-Based Harvesting Processes for Microalgae and Their Valuable-Related Molecules: A Review

The interest in microalgae production deals with its role as the third generation of feedstock to recover renewable energy. Today, there is a need to analyze the ultimate research and advances in recovering the microalgae biomass from the culture medium. Therefore, this review brings the current research developments (over the last three years) in the field of harvesting microalgae using membrane-based technologies (including microfiltration, ultrafiltration and forward osmosis). Initially, the principles of membrane technologies are given to outline the main parameters influencing their operation. The main strategies adopted by the research community for the harvesting of microalgae using membranes are subsequently addressed, paying particular attention to the novel achievements made for improving filtration performance and alleviating fouling. Moreover, this contribution also gives an overview of the advantages of applying membrane technologies for the efficient extraction of the high added-value compounds in microalgae cells, such as lipids, proteins and carbohydrates, which together with the production of renewable biofuels could boost the development of more sustainable and cost-effective microalgae biorefineries.

Current perspectives on integrated approaches to enhance lipid accumulation in microalgae

In recent years, research initiatives on renewable bioenergy or biofuels have been gaining momentum, not only due to fast depletion of finite reserves of fossil fuels but also because of the associated concerns for the environment and future energy security. In the last few decades, interest is growing concerning microalgae as the third-generation biofuel feedstock. The CO₂ fixation ability and conversion of it into value-added compounds, devoid of challenging food and feed crops, make these photosynthetic microorganisms an optimistic producer of biofuel from an environmental point of view. Microalgal-derived fuels are currently being considered as clean, renewable, and promising sustainable biofuel. Therefore, most research targets to obtain strains with the highest lipid productivity and a high growth rate at the lowest cultivation costs. Different methods and strategies to attain higher biomass and lipid accumulation in microalgae have been extensively reported in the previous research, but there are fewer inclusive reports that summarize the conventional methods with the modern techniques for lipid enhancement and biodiesel production from microalgae. Therefore, the current review focuses on the latest techniques and advances in different cultivation conditions, the effect of different abiotic and heavy metal stress, and the role of nanoparticles (NPs) in the stimulation of lipid accumulation in microalgae. Techniques such as genetic engineering, where particular genes associated with lipid metabolism, are modified to boost lipid synthesis within the microalgae, the contribution of "Omics" in metabolic pathway studies. Further, the contribution of CRISPR/Cas9 system technique to the production of microalgae biofuel is also briefly described.

Improving the lipid extraction yield from Chlorella based on the controllable electroporation of cell membrane by pulsed electric field

In order to solve the increasingly serious problems of energy and environment, microalgae are used as a raw material for extracting lipids to produce biodiesel. Prior to the extraction of lipids, microalgae were treated with high-voltage pulsed electric field (PEF) to break the cell membrane. It was found that the lipid extraction yield depends on the electric field strength (E) and the specific energy input (Wsp), and has a certain relationship with the cell disintegration rate of Chlorella. The perforation degree of the Chlorella's cell membrane by PEF treatment is controllable, moderate perforation can be ensured by controlling the power parameters. PEF treatment significantly improved the extraction yield of lipids. Compared with the test samples without PEF treatment, PEF treatment increased the lipid extraction yields by up to 166.67%. However, an excessively high voltage will cause the quality of the extracted biodiesel to decrease.

Production of Chlorella vulgaris Biomass in Tubular Photobioreactors during Different Culture Conditions

Biomass of microalgae and the components contained in their cells can be used for the production of heat, electricity, and biofuels. The aim of the presented study was to determine the optimal conditions that will be the most favorable for the production of large amounts of microalgae biomass intended for energy purposes. The study analyzed the effect of the type of lighting, the time of lighting culture, and the pH of the culture medium on the growth of Chlorella vulgaris biomass. The experiment was carried out in vertical tube photobioreactors in three photoperiods: 12/12, 18/6, and 24/0 h (light/dark). Two types of lighting were used in the work: high-pressure sodium light and light-emitting diode. The increase in biomass was determined by the gravimetric method, by the spectrophotometric method on the basis of chlorophyll a contained in the microalgae cells. The number of microalgae cells was also determined with the use of a hemocytometer. The optimal conditions for the production of biomass were recorded at a neutral pH, illuminating the cultures for 18 h a day. The obtained results were 546 ± 7.88 mg·L−1 dry weight under sodium lighting and 543 ± 1.92 mg·L−1 dry weight under light-emitting diode, with maximum biomass productivity of 27.08 ± 7.80 and 25.00 ± 5.1 mg·L−1∙d−1, respectively. The maximum content of chlorophyll a in cells was determined in the 12/12 h cycle and pH 6 (136 ± 14.13 mg∙m−3) under light-emitting diode and 18/6 h, pH 7 (135 ± 6.17 mg∙m−3) under sodium light, with maximum productivity of 26.34 ± 2.01 mg·m−3∙d−1 (light-emitting diode) and 24.21 ± 8.89 mg·m−3∙d−1 (sodium light). The largest number of microalgae cells (2.1 × 106) was obtained at pH 7 and photoperiod of 18/6 h under sodium light, and 12/12 h under light-emitting diode. Based on the results, it can be concluded that the determination of the optimal parameters for the growth and development of microalgae determines the production of their biomass, and such research should be carried out before starting the large-scale production process. In quantifying the biomass during cultivation, it is advantageous to use direct measurement methods.

Pyrolysis of Microalgae Chlorella sp. using Activated Carbon as Catalyst for Biofuel Production

Microalgae, as a potential raw material for biofuel, has several advantages compared to other biomass. One effective way to convert microalgae into biofuel is by thermal cracking or pyrolysis, and using a catalyst or not. So far, studies on the use of microalgae, that are converted into biofuels, is still use highly concentrated catalysts in packed bed reactors, which is not economical. Therefore, the aim of this study is to convert Chlorella sp. into biofuels with conventional pyrolysis without and using an activated carbon catalyst using packed bed reactor with bubble column. The reaction temperature is 400–600 °C, pyrolysis time is 1–4 hours, and the active carbon catalyst concentration is 0–2%. The 200 grams of Chlorella sp. and the catalyst was mixed in a fixed bed reactor under vacuum (−3 mm H20) condition. Next, we set the reaction temperature. When the temperature was reached, the pyrolysis was begun. After certain time was reached, the pyrolysis produced a liquid oil product. Oil products are measured for density and viscosity. The results showed that the conventional pyrolysis succeeded in converting microalgae Chlorella sp. into liquid biofuels. The highest yield of total liquid oil is obtained 50.2 % (heavy fraction yield, 43.75% and light fraction yield, 6.44%) at the highest conditions which was obtained with 1% activated carbon at a temperature and pyrolysis time of 3 hours. Physical properties of liquid biofuel are density of 0.88 kg/m3 and viscosity of 5.79 cSt. This physical properties are within the range of the national biodiesel standard SNI 7182-2012. The packed bed reactor completed with bubble column is the best choice for converting biofuel from microalgae, because it gives different fractions, so that it is easier to process further to the commercial biofuel stage. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Various potential techniques to reduce the water footprint of microalgal biomass production for biofuel-A review

Due to their rapid growth rates, high lipid productivity, and ability to synthesize value-added products, microalgae are considered as the potential biofuel feedstocks. However, among the several bottlenecks that are hindering the commercialization of microalgal biofuel synthesis, the issue of high water consumption is the least explored. This analysis, therefore, examines the factors that decide water use for the production of microalgae biofuel. Microalgae biodiesel water footprint varies from 3.5 to 3726 kg of water per kg of biodiesel. The study further investigates the cause for large variability in the estimation of the water footprint for microalgae fuel. Various strategies, including the reuse of harvested water, the use of high density cultivation that could be adopted for low water consumption in microalgal biofuel production are discussed. Specifically, the review identified a reciprocal relationship between biomass productivity and water footprint. On the basis of which the review emphasizes the significance of high density cultivation, which can be inexpensive and feasible relative to other water-saving techniques. With the setback of water scarcity due to the rapid industrialization in developing countries, the implementation of the cultivation system with a focus on minimizing the water consumption is inevitable for a successful large scale microalgal biofuel production.