A novel one-step method for oil-rich biomass production and harvesting by co-cultivating microalgae with filamentous fungi in molasses wastewater

Application of algal-mycelial pellets in the treatment of the mariculture wastewater

Hypersaline mariculture wastewater necessitates treatment prior to its discharge into marine environments. Algal-mycelial pellets (AMPs), known for their cost-effectiveness, energy efficiency and sustainability, have not been previously explored for their flocculation and pollutant removal capabilities in hyperhaline conditions. This work employed an orthogonal test design to investigate the effects of nine factors at three levels on the treatment efficiency of mariculture wastewater using Chlorella sp. TNBR1 and Aspergillus niger AMPs. The comprehensive optimal conditions for achieving the highest flocculation efficiency and pollutant removal are determined to be a temperature of 30 °C, light intensity of 6000 lux, a 12:0 light-dark cycle, an initial pH of 6, a microalgal density of 11.25 × 106 cell/mL, microalgal growth phase at the early logarithmic stage, a fungal spore density of 9.00 × 105 spore/mL and a fungal pellet phase of 60 h. Under such conditions, the treatment of nonsterile actual mariculture wastewater with Chlorella sp. TNBR1 and Aspergillus niger AMPs results in a 93.35 %±7.20 % reduction in chemical oxygen demand (COD), 92.83 %±7.29 % reduction in total nitrogen (TN), 100 % removal of total phosphorus (TP), and a flocculation efficiency of 69.21 %±5.36 %. These findings confirm that AMPs are a viable solution for effectively treating COD, TN and TP in real hypersaline mariculture wastewater, while also facilitating the flocculation and harvesting of microalgae.

Enhancing mixed-species microalgal biofilms for wastewater treatment: Design, construction, evaluation and optimisation

Biofilm-based cultivation of microalgae is a powerful method for wastewater treatment with low harvesting costs, water and energy consumption. This article provides a detailed summary of the design, construction, evaluation, and optimisation (DCEO) of mixed-species biofilms including algal and bacteria, and discusses their relevant applications in the treatment of industrial and agricultural wastewater and new pollutants. Finally, it presents the problems faced by mixed-species microalgal biofilms, along with solutions. DCEO is a typical synthetic biology concept, in which design and construction are bottom-up, and evaluation and optimisation are top-down approaches. Detailed knowledge of the metabolic pathways and the regulation of microalgae and other microorganisms is helpful for designing mixed-species biofilms. Three dimensional bioprinting is a powerful tool for constructing structured biofilms. Further analysis after evaluation is beneficial to optimise such biofilms. This review provides a new insight into using DCEO to enhance mixed-species biofilms for wastewater treatment.

Boosting microalgae-based carbon sequestration with the artificial CO2 concentration system

Global warming caused by CO2 emissions has been considered as one of the major challenges of this century. In an endeavor to control and reduce CO2 emissions, a series of Carbon dioxide Capture, Utilization, and Storage (CCUS) technologies have been developed specifically for the sequestration of CO2 from atmospheric air. Microalgae, as versatile and universal photosynthetic microorganisms, represent a promising avenue for biological CO2 sequestration. Nevertheless, further advancements are necessary to optimize microalgae-based carbon sequestration technology in terms of light reaction and dark reaction. This review discusses the current status of microalgae-based artificial CO2 sequestration technique, with a particular focus on the selection of CO2-resistant species, optimization of cultivation for CO2 sequestration, design of carbon concentration reactor, and the potential of synthetic biology to enhance CO2 solubility and biofixation efficiency. Furthermore, a discussion of Life cycle assessment and Techno-economic analysis regarding microalgae-based carbon capture was performed. The aim of this comprehensive review is to stimulate further research into microalgae-based CO2 sequestration, addressing challenges and opportunities for future development.

Advancements and hurdles in symbiotic microalgal co-cultivation strategies for wastewater treatment

Microalgae offer significant potential in various industrial applications, such as biofuel production and wastewater treatment, but the economic barriers to their cultivation and harvesting have been a major obstacle. However, a promising strategy involving co-cultivating microalgae in wastewater treatment could overcome the limitations of monocultivation and open the possibility for increased integration of microalgae into various industrial processes. This symbiotic relationship between microalgae and other microbes can enhance nutrient removal efficiency, increase value-added bioproduct production, promote carbon capture, and decrease energy consumption. However, unresolved challenges, such as the competition between microalgae and other microbes within the wastewater treatment system, may result in imbalances and reduced efficiency. The complexity of managing multiple microbes in a co-cultivation system poses difficulties in achieving stability and consistency in bioproduct production. In response to these challenges, strategies such as optimizing nutrient ratios, manipulating environmental conditions, understanding the dynamics of microbial relationships, and employing genetic modification to enhance the metabolic capabilities of microalgae and improve their competitiveness are critical in transitioning to a more sustainable path. Hence, this review will provide an in-depth analysis of recent advancements in symbiotic microalgal co-cultivation for applications in wastewater treatment and CO2 utilization, as well as discuss approaches for improving microalgal strains through genetic modification. Furthermore, the review will explore the use of efficient bioreactors, advanced control systems, and advancements in biorefinery processes.

Research Progress on the Mechanisms of Algal-Microorganism Symbiosis in Enhancing Large-Scale Lipid Production

Microalgae, characterized by their exceptional lipid content, rapid growth, and robust adaptability, represent a promising biological resource. In natural and engineered ecosystems, microalgae engage in intricate symbiotic relationships with diverse microorganisms, a dynamic interplay essential for ecological resilience and metabolic optimization. This review examines the role of symbiotic microorganisms in microalgal growth and lipid accumulation, with particular emphasis on the biological regulatory mechanisms that govern these processes. These include nutrient exchange, phytohormone-mediated growth stimulation, cofactors, and quorum-sensing-driven community coordination. The review highlights how these microbial interactions facilitate optimal lipid production by enhancing metabolic pathways, thereby improving the efficiency of lipid accumulation in microalgae. Furthermore, the review investigates horizontal gene transfer as an evolutionary driver that fortifies algal-microbial consortia against environmental stressors, enabling robust performance in fluctuating conditions. The integration of these biological insights holds transformative potential for advancing next-generation bioenergy platforms, where algal-microbial systems could play a pivotal role in enhancing biofuel production, wastewater treatment, and sustainable agriculture.

Tertiary treatment of dairy wastewater applying a microalga-fungus consortium

This paper aimed to apply filamentous fungi (Penicillium oxalicum and Cunninghamella echinulata), the microalga Tetradesmus obliquus and their co-culture in advanced treatment (tertiary treatment) of cheese whey. The bioremediation process was carried out in agitated flasks and bubble column bioreactors with different concentrations of chemical oxygen demand (COD) (223-1663 mg L-1), total nitrogen (TN) (13-61 mg L-1), and total phosphorus (TP) (3-26 mg L-1). The results obtained in shaken flasks showed a superiority of the consortium compared to the systems with separated species. In this sense, the treatment was carried out in a bubble column reactor, and the consortium formed by the microalga and the fungus C. echinulata showed a greater efficiency (at a light intensity of 100 µmol m-2 s-1), promoting by the symbiosis to reach removal efficiencies of up to 93.7, 78.8 and 93.4% for COD, TN and TP, respectively; meeting Brazilian and European standards for discharge into water bodies. In addition, no pH adjustment was required during the co-culture treatment, demonstrating the buffering effect of using these two types of microorganisms. Therefore, the use of the consortium formed by T. obliquus and C. echinulata as a remediator was highly promising to promote the advanced treatment of cheese whey.

Trilogy of comprehensive treatment of kitchen waste by bacteria-microalgae-fungi combined system: Pretreatment, water purification and resource utilization, and biomass harvesting

Given its profound disservice, a bacteria-microalgae-fungi combined system was designed to treat kitchen waste. Firstly, a new type of microbial agent homemade compound microorganisms (HCM) (composed of Serratia marcescens, Bacillus subtilis and other 11 strains) with relatively high bio-security were developed for pretreating kitchen waste, and HCM efficiently degraded 85.2 % cellulose, 94.3 % starch, and 59.0 % oil. HCM also accomplished brilliantly the initial nutrients purification and liquefaction conversion of kitchen waste. Under mono-culture mode (fungi and microalgae were inoculated separately in the pre - and post-stages) and co-culture mode (fungi and microalgae were inoculated simultaneously in the early stage), microalgae-fungi consortia were then applied for further water purification and resource utilization of kitchen waste liquefied liquid (KWLL) produced in the pretreatment stage. Two kinds of microalgae-fungi consortia (Chlorella sp. HQ and Chlorella sp. MHQ2 form consortia with pellet-forming fungi Aspergillus niger HW8-1, respectively) removed 79.5-83.0 % chemical oxygen demand (COD), 44.0-56.5 % total nitrogen (TN), 90.3-96.4 % total phosphorus (TP), and 64.9-71.0 % NH4+-N of KWLL. What's more, the microalgae-fungi consortia constructed in this study accumulated abundant high-value substances at the same time of efficiently purifying KWLL. Finally, in the biomass harvesting stage, pellet-forming fungi efficiently harvested 81.9-82.1 % of microalgal biomass in a low-cost manner through exopolysaccharides adhesion, surface proteins interaction and charge neutralization. Compared with conventional microalgae-bacteria symbiosis system, the constructed bacteria-microalgae-fungi new-type combined system achieves the triple purpose of efficient purification, resource utilization, and biomass recovery on raw kitchen waste through the trilogy strategy, providing momentous technical references and more treatment systems selection for future kitchen waste treatment.

Co-culture systems of microalgae and heterotrophic microorganisms: applications in bioproduction and wastewater treatment and elucidation of mutualistic interactions

In recent years, reducing the concentration of carbon dioxide in the atmosphere has become an important issue. Microalgae have a higher photosynthetic efficiency and growth rate than higher plants; thus, biological carbon dioxide fixation using microalgae is attracting particular attention as an efficient carbon dioxide fixation method. However, under dilute atmospheric conditions, microalgae exhibit lower growth rates and reduced carbon dioxide fixation efficiency. In recent years, technology that can efficiently fix carbon dioxide, even in the atmosphere, using a microalgae co-culture system that co-cultivates microalgae and heterotrophic microorganisms has attracted attention. In such a co-culture system, it is believed that a mutualistic relationship is established between microorganisms through the exchange of various compounds. This review focuses on the application of a co-culture system of microalgae and heterotrophic microorganisms for bioproduction and wastewater treatment. In addition, research to elucidate the mutualistic relationships in microalgal co-culture systems using analytical methods that have been widely used in recent years, such as next-generation sequencing technology, is also discussed. In the future, it is expected that the use of microalgae co-culture systems will expand on an industrial scale through the development of key technologies, such as efficient genetic modification techniques for microalgae and their heterotrophic microorganism partners, large-scale cultivation facilities that can efficiently cultivate microalgae, and stable control techniques for co-culture systems using advanced technology.

Re-vitalizing wastewater: Nutrient recovery and carbon capture through microbe-algae synergy using omics-biology

Increasing amounts of wastewater is the most pervasive and challenging environmental problem globally. Conventional treatment methods are costly and entail huge energy, carbon consumption and greenhouse gas emissions. Owing to their unique ability of carbon capturing and resource recovery, microalgae-microbiome based treatment is a potential approach and is widely used for carbon-neutral wastewater treatment. Microalgae-bacteria synergy (i.e., the functionally beneficial microbial synthetic communities) performs better and enhances carbon-sequestration and nutrient recovery from wastewater treatment plants. This review presents a comprehensive information regarding the potential of microalgae-microbiome as a sustainable agent for wastewater and discusses synergistic approaches for effective nutrient removal. Moreover, this review discusses, the role of omics-biology and Insilco approaches in unravelling and understanding the algae-microbe synergism and their response toward wastewater treatment. Finally, it discusses various microbiome engineering approaches for developing the effective microalgae-bacteria partners for carbon sequestration and nutrient recovery from wastewater, and summarizes future research perspectives on microalgae-microbiome based bioremediation.

Microalgae-mediated bioremediation: current trends and opportunities-a review

Environmental pollution poses a critical global challenge, and traditional wastewater treatment methods often prove inadequate in addressing the complexity and scale of this issue. On the other hand, microalgae exhibit diverse metabolic capabilities that enable them to remediate a wide range of pollutants, including heavy metals, organic contaminants, and excess nutrients. By leveraging the unique metabolic pathways of microalgae, innovative strategies can be developed to effectively remediate polluted environments. Therefore, this review paper highlights the potential of microalgae-mediated bioremediation as a sustainable and cost-effective alternative to conventional methods. It also highlights the advantages of utilizing microalgae and algae-bacteria co-cultures for large-scale bioremediation applications, demonstrating impressive biomass production rates and enhanced pollutant removal efficiency. The promising potential of microalgae-mediated bioremediation is emphasized, presenting a viable and innovative alternative to traditional treatment methods in addressing the global challenge of environmental pollution. This review identifies the opportunities and challenges for microalgae-based technology and proposed suggestions for future studies to tackle challenges. The findings of this review advance our understanding of the potential of microalgae-based technology wastewater treatment.

Ensuring carbon neutrality via algae-based wastewater treatment systems: Progress and future perspectives

The emergence of algal biorefineries has garnered considerable attention to researchers owing to their potential to ensure carbon neutrality via mitigation of atmospheric greenhouse gases. Algae-derived biofuels, characterized by their carbon-neutral nature, stand poised to play a pivotal role in advancing sustainable development initiatives aimed at enhancing environmental and societal well-being. In this context, algae-based wastewater treatment systems are greatly appreciated for their efficacy in nutrient removal and simultaneous bioenergy generation. These systems leverage the growth of algae species on wastewater nutrients-including carbon, nitrogen, and phosphorus-alongside carbon dioxide, thus facilitating a multifaceted approach to pollution remediation. This review seeks to delve into the realization of carbon neutrality through algae-mediated wastewater treatment approaches. Through a comprehensive analysis, this review scrutinizes the trajectory of algae-based wastewater treatment via bibliometric analysis. It subsequently examines the case studies and empirical insights pertaining to algae cultivation, treatment performance analysis, cost and life cycle analyses, and the implementation of optimization methodologies rooted in artificial intelligence and machine learning algorithms for algae-based wastewater treatment systems. By synthesizing these diverse perspectives, this study aims to offer valuable insights for the development of future engineering applications predicated on an in-depth understanding of carbon neutrality within the framework of circular economy paradigms.

Biocompounds from wastewater-grown microalgae: a review of emerging cultivation and harvesting technologies

Microalgae biomass has attracted attention as a feedstock to produce biofuels, biofertilizers, and pigments. However, the high production cost associated with cultivation and separation stages is a challenge for the microalgae biotechnology application on a large scale. A promising approach to overcome the technical-economic limitations of microalgae production is using wastewater as a nutrient and water source for cultivation. This strategy reduces cultivation costs and contributes to valorizing sanitation resources. Therefore, this article presents a comprehensive literature review on the status of microalgae biomass cultivation in wastewater, focusing on production strategies and the accumulation of valuable compounds such as lipids, carbohydrates, proteins, fatty acids, and pigments. This review also covers emerging techniques for harvesting microalgae biomass cultivated in wastewater, discussing the advantages and limitations of the process, as well as pointing out the main research opportunities. The novelty of the study lies in providing a detailed analysis of state-of-the-art and potential advances in the cultivation and harvesting of microalgae, with a special focus on the use of wastewater and implementing innovative strategies to enhance productivity and the accumulation of compounds. In this context, the work aims to guide future research concerning emerging technologies in the field, emphasizing the importance of innovative approaches in cultivating and harvesting microalgae for advancing knowledge and practical applications in this area.

Manipulation of co-pelletization for Chlorela vulgaris harvest by treatment of Aspergillus niger spore

The co-pelletization of microalgae with filamentous fungi was a promising approach for microalgae harvest. However, the real conditions of microalgae growth limited the arbitrary optimization of co-pellets formation with filamentous fungi. Therefore, it is urgent to develop an approach to manipulate the co-pelletization through treatment of A. niger spores. In this study, Aspergillus niger and Chlorella vulgaris were used as the model species of filamentous fungi and microalgae to investigate co-pellets formation using A. niger spores after by different pH solutions treatment, swelling, snailase treatment. The importance of spore treatments on C. vulgaris harvest in sequence was claimed based on response surface methodology analysis. The pH solutions treatment, swelling, snailase treatment of A. niger spore contributed 21.0%, 10.5%, 40.7% of harvest ratio of C. vulgaris respectively, which guided the application of spore treatment into co-pelletization. Treatment of spore was showed as an efficient approach to manipulate co-pelletization for microalgae harvest in diverse microalgae condition. This results promoted the application of co-pelletization technology in microalgae harvest of various conditions.

A fungal-algal self-flocculation system and its application to treat filter sludge leachate in the sugar industry

The efficient and economical treatment of wastewater using microalgae has attracted much attention. However, harvesting microalgae cells from treated wastewater remains challenging. In the present study, a Chlorella vulgaris suspension containing filamentous fungi Aspergillus niger and Chaetomium gracile was successfully used to construct a self-flocculating system, with a microalgae flocculation efficiency of 99.6% achieved by gravity sedimentation within 4 h. The diameter of fungi played an important role in determining flocculation efficiency, and the optimal particle size was 10 mm. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) results indicated that the sweeping action of fungal mycelia and the interaction between the functional groups of fungi and the C. vulgaris surface contributed to improve flocculation. Co-cultivation of C. vulgaris and fungi could effectively remove 83.53%, 94.45% and 76.88% of total phosphorus, total nitrogen and chemical oxygen demand, respectively, from the sludge leachate from a sugar mill. The fungal-algal biomass reached 5.75 g/L. Herein, the constructed self-flocculation system had coupled efficient flocculation of C. vulgaris with removal of pollutants from wastewater in a short period of time, and providing a green, pollution-free, low-cost method for simultaneous wastewater treatment and the production of high quality biomass.

Enhancement of carbon nanotubes on microalgal-fungal consortium formation and wastewater treatment

As a promising material with an efficient light capture capability, a low amount of carbon nanotubes can affect growth and photosynthesis by regulating microalgal cells, thereby enhancing the pollutant removal efficiency in wastewater. In this study, microalgal-fungal consortia of Chlorella vulgaris and Ganoderma lucidum were developed with different types and concentrations of carbon nanotubes. The treatment effect of microalgal-fungal consortia on simulated digestate was also studied. The results demonstrate that 1.5 mg/L of carboxylated multi-walled carbon nanotubes remarkably promoted the formation, growth and photosynthesis of consortium. The dry weight and chlorophyll a content reached 19.3 ± 0.53 mg/symbiont and 27.3 ± 0.52 μg/L, respectively. Moreover, the removal efficiency of chemical oxygen demand, total nitrogen, total phosphorus and tetracycline hydrochloride were 94.1%, 65.5%, 61.9% and 96.2%, respectively. Overall, these findings suggest a promising future for the use of carbon nanotubes in wastewater treatment by regulating microalgal-fungal consortia.

Microalgal co-cultivation -recent methods, trends in omic-studies, applications, and future challenges

The burgeoning human population has resulted in an augmented demand for raw materials and energy sources, which in turn has led to a deleterious environmental impact marked by elevated greenhouse gas (GHG) emissions, acidification of water bodies, and escalating global temperatures. Therefore, it is imperative that modern society develop sustainable technologies to avert future environmental degradation and generate alternative bioproduct-producing technologies. A promising approach to tackling this challenge involves utilizing natural microbial consortia or designing synthetic communities of microorganisms as a foundation to develop diverse and sustainable applications for bioproduct production, wastewater treatment, GHG emission reduction, energy crisis alleviation, and soil fertility enhancement. Microalgae, which are photosynthetic microorganisms that inhabit aquatic environments and exhibit a high capacity for CO2 fixation, are particularly appealing in this context. They can convert light energy and atmospheric CO2 or industrial flue gases into valuable biomass and organic chemicals, thereby contributing to GHG emission reduction. To date, most microalgae cultivation studies have focused on monoculture systems. However, maintaining a microalgae monoculture system can be challenging due to contamination by other microorganisms (e.g., yeasts, fungi, bacteria, and other microalgae species), which can lead to low productivity, culture collapse, and low-quality biomass. Co-culture systems, which produce robust microorganism consortia or communities, present a compelling strategy for addressing contamination problems. In recent years, research and development of innovative co-cultivation techniques have substantially increased. Nevertheless, many microalgae co-culturing technologies remain in the developmental phase and have yet to be scaled and commercialized. Accordingly, this review presents a thorough literature review of research conducted in the last few decades, exploring the advantages and disadvantages of microalgae co-cultivation systems that involve microalgae-bacteria, microalgae-fungi, and microalgae-microalgae/algae systems. The manuscript also addresses diverse uses of co-culture systems, and growing methods, and includes one of the most exciting research areas in co-culturing systems, which are omic studies that elucidate different interaction mechanisms among microbial communities. Finally, the manuscript discusses the economic viability, future challenges, and prospects of microalgal co-cultivation methods.

Nutrient removal and biogas upgrade using co-cultivation of Chlorella vulgaris and three different bacteria under various GR24 concentrations by induction with 5-deoxystrigol

Algae symbiosis technology shows great potential in the synchronous treatment of biogas slurry and biogas, which has promising applications. For improving nutrients and CO₂ removal rates, the present work constructed four microalgal systems: Chlorella vulgaris (C. vulgaris) monoculture, C. vulgaris-Bacillus licheniformis (B. licheniformis), C. vulgaris-activated sludge, and C. vulgaris-endophytic bacteria (S395-2) to simultaneously treat biogas as well as biogas slurry under GR24 and 5DS induction. Our results showed that the C. vulgaris-endophytic bacteria (S395-2) showed optimal growth performance along with photosynthetic activity under the introduction of GR24 (10^-9 M). Under optimal conditions, CO₂ removal efficiency form biogas, together with chemical oxygen demand, total phosphorus and total nitrogen removal efficiencies from biogas slurry reached 67.25 ± 6.71%, 81.75 ± 7.93%, 83.19 ± 8.32%, and 85.17 ± 8.26%, respectively. The addition of symbiotic bacteria isolated from microalgae can promote the growth of C. vulgaris, and the exogenous addition of GR24 and 5DS can strengthen the purification performance of the algae symbiosis to achieve the maximum removal of conventional pollutants and CO₂.

Insights into differences between spore-assisted and pellet-assisted microalgae harvesting using a highly efficient fungus: Efficiency, high-value substances, and mechanisms

To achieve efficient and low-cost microalgae harvesting, investigations were conducted on the harvesting efficiency and potential mechanisms of Chlorella sp. HQ by filamentous fungi using two strategies, fungal spore-assisted harvesting (FSH) and fungal pellet-assisted harvesting (FPH). Five of the 19 fungal species isolated from domestic sewage could form pellets, and Aspergillus niger HW8-1 comprised the highest harvesting efficiencies of 99.17 % and 88.70 % for FPH and FSH, respectively. FSH had 2-3 times more lipids and polysaccharides in fungus-alga pellets and caused richer saturated and monounsaturated fatty acids compared with FPH. Moreover, by optimizing the microalgae preculture time, glucose concentration, and microalgae initial density, the contents of high-value substances, such as lipids, polysaccharides, and proteins of fungus-alga pellets after FPH were improved from 5.96 %, 5.67 %, and 7.27 % to 20.18 %, 24.34 % and 10.48 %, respectively. Furthermore, fungal pellets secreted more extracellular polymeric substances (EPS) during FPH than those by FSH, which could chemisorb algal cells by lowering the surface potential of fungal pellets. FPH caused algal cells to cover the outside, which increased the light exposure area of algae, thereby increasing the photosynthesis rate, whereas FSH mainly captured microalgae physically through mycelium entanglement.

Quorum Sensing as a Trigger That Improves Characteristics of Microbial Biocatalysts

Quorum sensing (QS) of various microorganisms (bacteria, fungi, microalgae) today attracts the attention of researchers mainly from the point of view of clarifying the biochemical basics of this general biological phenomenon, establishing chemical compounds that regulate it, and studying the mechanisms of its realization. Such information is primarily aimed at its use in solving environmental problems and the development of effective antimicrobial agents. This review is oriented on other aspects of the application of such knowledge; in particular, it discusses the role of QS in the elaboration of various prospective biocatalytic systems for different biotechnological processes carried out under aerobic and anaerobic conditions (synthesis of enzymes, polysaccharides, organic acids, etc.). Particular attention is paid to the biotechnological aspects of QS application and the use of biocatalysts, which have a heterogeneous microbial composition. The priorities of how to trigger a quorum response in immobilized cells to maintain their long-term productive and stable metabolic functioning are also discussed. There are several approaches that can be realized: increase in cell concentration, introduction of inductors for synthesis of QS-molecules, addition of QS-molecules, and provoking competition between the participants of heterogeneous biocatalysts, etc.).

Microbial Interactions between Marine Microalgae and Fungi: From Chemical Ecology to Biotechnological Possible Applications

Chemical interactions have been shown to regulate several marine life processes, including selection of food sources, defense, behavior, predation, and mate recognition. These chemical communication signals have effects not only at the individual scale, but also at population and community levels. This review focuses on chemical interactions between marine fungi and microalgae, summarizing studies on compounds synthetized when they are cultured together. In the current study, we also highlight possible biotechnological outcomes of the synthetized metabolites, mainly for human health applications. In addition, we discuss applications for bio-flocculation and bioremediation. Finally, we point out the necessity of further investigating microalgae-fungi chemical interactions because it is a field still less explored compared to microalga-bacteria communication and, considering the promising results obtained until now, it is worthy of further research for scientific advancement in both ecology and biotechnology fields.

Rice straw as microalgal biofilm bio-carrier: Effects of indigenous microorganisms on rice straw and microalgal biomass production

Microalgal biofilm cultivation is a promising method for efficient microalgae production. However, expensive, difficult-to-obtain and non-durable carriers hinder its up-scaling. This study adopted both sterilized and unsterilized rice straw (RS) as a carrier for the development of microalgal biofilm, with polymethyl methacrylate as control. The biomass production and chemical composition of Chlorella sorokiniana, as well as the microbial community composition during cultivation were examined. The physicochemical properties of RS before and after utilized as carrier were investigated. The biomass productivity of unsterilized RS biofilm exceeded that of suspended culture by 4.85 g m^-2·d^-1. The indigenous microorganisms, mainly fungus, could effectively fixed microalgae to the bio-carrier and enhance its biomass production. They could also degrade RS into dissolved matters for microalgal utilization, leading to the physicochemical properties change of RS in the direction which favored its energy conversion. This study showed that RS can be used effectively as a microalgal biofilm carrier, thus presenting a new possibility for the recycling of rice straw.

Integrated culture and harvest systems for improved microalgal biomass production and wastewater treatment

Microalgae cultivation in wastewater has received much attention as an environmentally sustainable approach. However, commercial application of this technique is challenging due to the low biomass output and high harvesting costs. Recently, integrated culture and harvest systems including microalgae biofilm, membrane photobioreactor, microalgae-fungi co-culture, microalgae-activated sludge co-culture, and microalgae auto-flocculation have been explored for efficiently coupling microalgal biomass production with wastewater purification. In such systems, the cultivation of microalgae and the separation of algal cells from wastewater are performed in the same reactor, enabling microalgae grown in the cultivation system to reach higher concentration, thus greatly improving the efficiency of biomass production and wastewater purification. Additionally, the design of such innovative systems also allows for microalgae cells to be harvested more efficiently. This review summarizes the mechanisms, characteristics, applications, and development trends of the various integrated systems and discusses their potential for broad applications, which worth further research.

A state of the art review on the co-cultivation of microalgae-fungi in wastewater for biofuel production

The microalgae have a great potential as the fourth generation biofuel feedstock to deal with energy crisis, but the cost of production and biomass harvest are the major hurdles in terms of large scale production and applications. Using filamentous fungi to culture targeted alga for biomass accumulation and eventually harvesting is a sustainable way to mitigate environmental impacts. Microalgal co-culture method could be an alternative to overcome limitations and increase biomass yield and lipid accumulation. It was found to be the high feasibility for the production of biofuels from fungi and microalgae using wastewater. This article aimed to state the synergistic approaches, their culture protocols, harvesting procedure and their potential biotechnological applications. Additionally, algal-fungal consortia could digest cellulosic biomass, potentially reducing operating costs as part of industrial need. As a result of co-cultivation, biofuel production could be economically feasible owing to its excellent ability to treat wastewater and be eco-friendly. The implications of the innovative co-cultivation technology have demonstrated the potential for further development based on the policies that have been supported and implemented.

Nutrient removal from biogas slurry and biogas upgrading by microalgae-fungi-bacteria co-cultivation under different carbon nanotubes concentration

In this study, Chlorella vulgaris, Ganoderma lucidum, and endophytic bacteria were co-cultivated with the stimulation of strigolactone analogs GR24 to prepare pellets. During the purification of biogas slurry and biogas, multi-walled carbon nanotubes (MWCNTs) were introduced to enhance the removal efficiencies of nutrients and CO₂. The results showed that both GR24 and MWCNTs affected the purification of biogas slurry and biogas. The maximum chemical oxygen demand, total nitrogen, total phosphorus, and CO₂ removal efficiencies of the Chlorella vulgaris-Ganoderma lucidum-endophytic bacterial symbionts were 82.57 ± 7.96% (P < 0.05), 82.14 ± 7.87% (P < 0.05), 84.27 ± 7.96% (P < 0.05), and 63.93 ± 6.22% (P < 0.05), respectively, with the induction of 10^-9 M GR24 and 1 mg L^-1 MWCNTs. Moreover, the growth and photosynthetic performance of the symbionts were consistent with the removal effects. The Chlorella vulgaris-Ganoderma lucidum-endophytic bacterial symbionts obtained high growth rates and enzyme activity with the maximum growth rate of 0.365 ± 0.03 d^-1, mean daily productivity of 0.182 ± 0.016 g L^-1 d^-1, and carbonic anhydrase activity of 31.07 ± 2.75 units, respectively. These results indicated that an appropriate concentration of GR24 and MWCNTs could promote the growth of symbionts, reinforce the purification effects of biogas slurry and biogas, and provide a new idea for the simultaneous purification of wastewater and biogas.

Chitosan-coated oleaginous microalgae-fungal pellets for improved bioremediation of non-sterile secondary effluent and application in carbon dioxide sequestration in bubble column photobioreactors

Oleaginous microalga Scenedesmus sp. SPP was rapidly immobilized in oleaginous fungal pellets by their opposite-surface-charges. Microalgae-fungal (MF) pellets were more effective in bioremediation of non-sterile secondary effluent than mono-culture. The optimal hydraulic retention time for dual bioremediation in semi-continuous mode was 72 h. The MF pellets coated with 0.4 %-chitosan improved removal efficiencies of COD, total nitrogen (TN), and total phosphorus (TP) up to 96.2±0.0 %, 88.2±2.8 % and 71.5±0.7 %, respectively, likely because of better cell retention and more nutrient adsorption and assimilation. Dual bioremediation by coated MF pellets was also successfully scaled up in 30-L bubble-column photobioreactors with improved COD, TN, and TP removal efficiencies of 98.5±0.0 %, 90.2±0.0 % and 79.5±2.1 %, respectively. This system also effectively removed CO₂ from simulated flue gas at 71.2±0.4 % and produced biomass with high lipid content. These results highlight the effectiveness of bio-immobilization by fungal pellets; chitosan coating; and their practical applications in bioremediation and CO₂ sequestration.

A rapid and simplified method for evaluating the performance of fungi-algae pellets: A hierarchical analysis model

Microbial pellets technology has undergone extensive research recently and has increasingly matured, showing significant promise. However, the performance of microbial pellets cannot be predicted quickly by the current evaluating methods because they are complicated to operate, take a long time, and pose a risk to the environment. In this study, a representative microbial pellet, fungi-algae pellet, was selected as the research object. Eight evaluation parameters and four evaluation indices were chosen to construct the performance evaluation system of the fungal-algal pellets using the analytic hierarchy process (AHP) and weighting method. Combining the correlation analysis and expert opinion, we found that among the eight parameters selected, the adsorption saturation rate of mycelial pellets on algae had the most significant influence weight on the performance of fungi-algae pellet, followed by algal culture time and fungal incubation time. This research proposes and validates the Performance Evaluation Value (PEV) of fungi-algae pellet and its calculation method. We also discuss the effectiveness of this new evaluation system in saving time, cost, and emission reductions. The results of this paper enable the rapid evaluation of fungi-algae pellets and promote the better development of fungi-algae pellets technology and even other multi-microbial symbiotic pellet technologies.

Myco- and phyco-remediation of polychlorinated biphenyls in the environment: a review

Polychlorinated biphenyls (PCBs) are toxic organic compounds and pose serious threats to environment and public health. PCBs still exist in different environments such as air, water, soil, and sediments even on ban. This review summarizes the phyco- and myco-remediation technologies developed to detoxify the PCB-polluted sites. It was found that algae mostly use bioaccumulation to biodegradation strategies to reclaim the environment. As bio-accumulator, Ulva rigida C. Agardh has been best at 25 ng/g dry wt to remove PCBs. Evidently, Anabaena PD-1 is the only known PCB degrading alga and efficiently degrade Aroclor 1254 and dioxin-like PCBs up to 84.4% and 37.4% to 68.4%, respectively. The review suggested that factors such as choice of algal strains, response of microalgae, biomass, the rate of growth, and cost-effective cultivation conditions significantly influence the remediation of PCBs. Furthermore, the Anabaena sp. linA gene of Pseudomonas paucimobilis Holmes UT26 showed enhanced efficiency. Pleurotus ostreatus (Jacq.) P. Kumm is the most efficient PCB degrading fungus, degrading up to 98.4% and 99.6% of PCB in complex and mineral media, respectively. Combine metabolic activities of bacteria and yeast led to the higher detoxification of PCBs. Fungi-algae consortia would be a promising approach in remediation of PCBs. A critical analysis on potentials and limits of PCB treatment through fungal and algal biosystems have been reviewed, and thus, new insights have emerged for possible bioremediation, bioaccumulation, and biodegradation of PCBs.

Microalgae on distillery wastewater treatment for improved biodiesel production and cellulose nanofiber synthesis: A sustainable biorefinery approach

Sugarcane spent wash generates waste at a large scale that impacts the environment, hence the classic waste reuse technology needs to be implemented. An integrated approach of spent wash and microalgae cultivation to produce biodiesel has gained momentum in recent times. However, the microalgae technology lacks the functional utilization of de-oiled microalgae biomass (DOB). This study proposed the development of a microalgae-based advanced process for distillery spent wash treatment, biomass recovery for biodiesel and utilizing algal residue as a step towards waste management. A novel microalga Coelastrella sp KJ-04 grown in distillery spent wash represented with high biomass (4.61g/L) and lipid production (3.6 g/L). The significant reduction in Chemical Oxygen Demand (COD, 49.3%), Total Nitrogen (TN, 49.7%), Total Phosphorous (TP, 21.8%), Total Organic Carbon (TOC, 40.2%), Total Sulphur (S, 37.2%) and Potassium (K, 42.5%) were achieved in spent wash. The extracted lipids of Coelastrella sp KJ-04 were converted to Fatty acid methyl ester (FAME) and examined by Gas chromatography -mass spectrometry (GC-MS) to observe the suitability for biodiesel prospect. The de-oiled biomass (DOB) was utilized for the synthesis of Cellulose nanofibers (CNF), purified and estimated with a diameter ranging between 20 and 27 nm. The crystalline structure and functional group of CNF were analyzed by X-ray diffraction (XRD) and Fourier Transform infrared spectroscopy (FTIR). The unprecedented work demonstrated the microalgae biorefinery approach for spent wash remediation, biodiesel synthesis and simultaneous production of biodegradable CNF from algal residue to support waste-free technology. In future, CNF can be reinforced into material for concrete as it could be the smart alternative to replace synthetic cement plastics.

Review on rewiring of microalgal strategies for the heavy metal remediation - A metal specific logistics and tactics

Phycoremediation of heavy metals are gaining much attention and becoming an emerging practice for the metal removal in diverse environmental matrices. Still, the physicochemical state of metal polluted sites is often found to be complex and haphazard in nature due to the irregular discharge of wastes, that leads to the lack of conjecture on the application of microalgae for the metal bioremediation. Besides, the foresaid issues might be eventually ended up with futile effect to the polluted site. Therefore, this review is mainly focusing on interpretative assessment on pre-existing microalgal strategies and their merits and demerits for selected metal removal by microalgae through various process such as natural attenuation, nutritional amendment, chemical pretreatment, metal specific modification, immobilization and amalgamation, customization of genetic elements and integrative remediation approaches. Thus, this review provides the ideal knowledge for choosing an efficient metal remediation tactics based on the state of polluted environment. Also, this in-depth description would provide the speculative knowledge of counteractive action required for pass-over the barriers and obstacles during implementation. In addition, the most common metal removal mechanism of microalgae by adsorption was comparatively investigated with different metals through the principal component analysis by grouping various factor such as pH, temperature, initial metal concentration, adsorption capacity, removal efficiency, contact time in different microalgae. Conclusively, the suitable strategies for different heavy metals removal and addressing the complications along with their solution is comprehensively deliberated for metal removal mechanism in microalgae.

Capturing effects of filamentous fungi Aspergillus flavus ZJ-1 on microalgae Chlorella vulgaris WZ-1 and the application of their co-integrated fungi-algae pellets for Cu(II) adsorption

Using filamentous fungi to capture unicellular microalgae is an effective way for microalgae recovery in water treatment. Here, fungi Aspergillus flavus ZJ-1 and microalgae Chlorella vulgaris WZ-1 isolated from a copper tailings pond were used to study the capture effect of ZJ-1 on WZ-1. The highest capture efficiency (97.85%) was obtained within 6 h under the optimized conditions of 30 °C, 150 rpm, fungi-algae biomass ratio of 2.24:1, and initial pH of 9.24 in microalgae medium. The formed fungi-algae pellets (FAPs) were further used to remove Cu(II) from aqueous solution. Results showed that the FAPs formed at different capture times all adsorbed Cu(II) well, and the PAFs formed within 2 h (PAFs_2 h) exhibited the highest Cu(II) adsorption capacity (80.42 mg·g^-1). SEM images showed that Cu(II) caused a change in the internal structure of PAFs_2 h from loose to compact, the mycelium shrunk, and the microalgal cells were concave. Cu(II) adsorption by PAFs_2 h was well conformed to the pseudo-second-order kinetics and the Langmuir isotherm (123.61 mg·g^-1 of theoretically maximum adsorption capacity). This work opens a way for applying FAPs in the remediation of heavy metal-contaminated wastewater, and the metal adsorption effect was determined by the capture amount of microalgae.

Transformation of Enzymatic Hydrolysates of Chlorella–Fungus Mixed Biomass into Poly(hydroxyalkanoates)

The production of poly(hydroxylalkanoates) (PHA) is limited by the high cost of the feedstock since various biomass wastes look attractive as possible sources for polymer production. The originality of this present study is in the biotransformation of mixed Chlorella-based substrates into PHAs. The synthetic potential of Cupriavidus necator B8619 cells was studied during the bioconversion of algae biomass in mixtures with spent immobilized mycelium of different fungi (genus Rhizopus and Aspergillus) into PHAs. The biomass of both microalgae Chlorella and fungus cells was accumulated due to the use of the microorganisms in the processes of food wastewater treatment. The biosorption of Chlorella cells by fungal mycelium was carried out to obtain mixed biomass samples (the best ratio of “microalgae:fungi” was 2:1) to convert them by C. necator B8619 into the PHA. The influence of conditions used for the pretreatment of microalgae and mixed types of biomass on their conversion to PHA was estimated. It was found that the maximum yield of reducing sugars (39.4 ± 1.8 g/L) can be obtained from the mechanical destruction of cells by using further enzymatic hydrolysis. The effective use of the enzymatic complex was revealed for the hydrolytic disintegration of treated biomass. The rate of the conversion of mixed substrates into the biopolymer (440 ± 13 mg/L/h) appeared significantly higher compared to similar known examples of complex substrates used for C. necator cells.

Microalgae-based wastewater treatment: Mechanisms, challenges, recent advances, and future prospects

The rapid expansion of both the global economy and the human population has led to a shortage of water resources suitable for direct human consumption. As a result, water remediation will inexorably become the primary focus on a global scale. Microalgae can be grown in various types of wastewaters (WW). They have a high potential to remove contaminants from the effluents of industries and urban areas. This review focuses on recent advances on WW remediation through microalgae cultivation. Attention has already been paid to microalgae-based wastewater treatment (WWT) due to its low energy requirements, the strong ability of microalgae to thrive under diverse environmental conditions, and the potential to transform WW nutrients into high-value compounds. It turned out that microalgae-based WWT is an economical and sustainable solution. Moreover, different types of toxins are removed by microalgae through biosorption, bioaccumulation, and biodegradation processes. Examples are toxins from agricultural runoffs and textile and pharmaceutical industrial effluents. Microalgae have the potential to mitigate carbon dioxide and make use of the micronutrients that are present in the effluents. This review paper highlights the application of microalgae in WW remediation and the remediation of diverse types of pollutants commonly present in WW through different mechanisms, simultaneous resource recovery, and efficient microalgae-based co-culturing systems along with bottlenecks and prospects.

Artificial microbial consortia for bioproduction processes

The application of artificial microbial consortia for biotechnological production processes is an emerging field in research as it offers great potential for the improvement of established as well as the development of novel processes. In this review, we summarize recent highlights in the usage of various microbial consortia for the production of, for example, platform chemicals, biofuels, or pharmaceutical compounds. It aims to demonstrate the great potential of co-cultures by employing different organisms and interaction mechanisms and exploiting their respective advantages. Bacteria and yeasts often offer a broad spectrum of possible products, fungi enable the utilization of complex lignocellulosic substrates via enzyme secretion and hydrolysis, and microalgae can feature their abilities to fixate CO2 through photosynthesis for other organisms as well as to form lipids as potential fuelstocks. However, the complexity of interactions between microbes require methods for observing population dynamics within the process and modern approaches such as modeling or automation for process development. After shortly discussing these interaction mechanisms, we aim to present a broad variety of successfully established co-culture processes to display the potential of artificial microbial consortia for the production of biotechnological products.

Potential use of algae for the bioremediation of different types of wastewater and contaminants: Production of bioproducts and biofuel for green circular economy

Remediation by algae is a very effective strategy for avoiding the use of costly, environmentally harmful chemicals in wastewater treatment. Recently, industries based on biomass, especially the bioenergy sector, are getting increasing attention due to their environmental acceptability. However, their practical application is still limited due to the growing cost of raw materials such as algal biomass, harvesting and processing limitations. Potential use of algal biomass includes nutrients recovery, heavy metals removal, COD, BOD, coliforms, and other disease-causing pathogens reduction and production of bioenergy and valuable products. However, the production of algal biomass using the variable composition of different wastewater streams as a source of growing medium and the application of treated water for subsequent use in agriculture for irrigation has remained a challenging task. The present review highlights and discusses the potential role of algae in removing beneficial nutrients from different wastewater streams with complex chemical compositions as a biorefinery concept and subsequent use of produced algal biomass for bioenergy and bioactive compounds. Moreover, challenges in producing algal biomass using various wastewater streams and ways to alleviate the stress caused by the toxic and high concentrations of nutrients in the wastewater stream have been discussed in detail. The technology will be economically feasible and publicly accepted by reducing the cost of algal biomass production and reducing the loaded or attached concentration of micropollutants and pathogenic microorganisms. Algal strain improvement, consortium development, biofilm formation, building an advanced cultivation reactor system, biorefinery concept development, and life-cycle assessment are all possible options for attaining a sustainable solution for sustainable biofuel production. Furthermore, producing valuable compounds, including pharmaceutical, nutraceutical and pigment contents generated from algal biomass during biofuel production, could also help reduce the cost of wastewater management by microalgae.

Removal of antibiotic resistance genes and mobile genetic elements in a three-stage pig manure management system: The implications of microbial community structure

In this work, the removal of antibiotic resistance genes (ARGs) in the industrial-scale pig manure management system has been investigated. Additionally, the implications of mobile genetic elements (MGEs) and microbial community structure have been discussed. During the whole period of manure management, 19 ARGs and 7 MGEs were obtained from the system. The results identified that the 9 ARGs and 2 MGEs were removed from the pig manure-based materials after composting, while 5 ARGs and 2 MGEs were still remained, indicating that the ARGs/MGEs could not be removed completely as contaminants by composting. The pig farm without additional antibiotics in-feed was still faced with the risk of ARGs/MGEs from outside. Microbial community analysis illuminated that a greater decrease in the abundance of norank_f__JG30-KF-CM45, Corynebacterium, Terrisporobacter, Truepera, Salinispora and Clostridium, was responsible for the removal of ARGs/MGEs. The genes, including tnpA-01, tnpA-02, tnpA-05, Tp614, tetQ, tetM-01, tetR-02, tetX, cfxA, floR, dfrA1 and ermF exhibited significantly positive correlation with fungal communities. Fungal community analysis verified that a remarkable decrease in the abundance of Aspergillus and Thermomyces after composting was responsible for the ARGs/MGEs removal. The results elucidated the crucial roles of the related bacterial and fungal communities in the removal of ARGs/MGEs. The compound microbial agent assisted the temperature rise of composting, thereby changing the related microbial community structure and resulting in ARGs/MGEs removal.

Advanced simultaneous nitrogen and phosphorus removal for non-sterile wastewater through a novel coupled yeast-sludge system: Performance, microbial interaction, and mechanism

A novel coupled yeast-sludge system (CYSS) was constructed by the yeast Candida sp. PNY integrated with activated sludge to treat non-sterile mainstream wastewater. After 240-day cultivation, compared with single activated sludge, simultaneous removal efficiency of total organic carbon (TOC), nitrogen and phosphorus increased by 19.5% (176.34 mg TOC g^-1 d^-1), 21.3% (11.25 mg TN g^-1 d^-1) and 15.0% (6.95 mg TP g^-1 d^-1), respectively, while the amount of sludge reduced by 50%. Amplicon sequencing analysis showed that the abundance of Nitrosomonas, Nitrospira, Zoogloea, Dechloromonas, and Candidatus Accumulibacter significantly decreased to 0% on Day 200. Abundance of nirS and nirK for denitrification significantly decreased in CYSS by quantitative PCR (qPCR), and the copies of nirS and nirK were 3.37-fold and 1.71-fold decrease from Day 0 to Day 240, respectively. The results of Fluorescence in situ hybridization and co-occurrence network showed that Candida sp. PNY predominated its distribution in CYSS, and strongly connected with environmental variables based on network analysis. Furthermore, this study reconstructed the carbon, nitrogen and phosphorus metabolic pathways of the CYSS based on metagenomics.

Effect of different mixed light-emitting diode light wavelengths on CO2 absorption from biogas and nutrient removal from biogas slurry by microalgae and fungi induced using strigolactone and endophytic bacteria

In this study, biogas and biogas slurry were simultaneously treated using two symbiotic systems: Chlorella vulgaris-Ganoderma lucidum-S395-2 (endophytic bacteria) and Scenedesmus obliquus-G. lucidum-S395-2. The influence of different mixed illumination (red and blue) intensity ratios on the algal symbionts' extracellular carbonic anhydrase activities was investigated, as well as the rates of microalgal growth and photosynthesis. The treatment performance was simultaneously assessed in terms of the efficiency of organic matter or nutrient removal and the level of CO2 absorption. The results indicated that red-blue light combinations with an intensity ratio of 5:5 were optimal. When comparing the performance of the two symbiotic systems, the C. vulgaris-G. lucidum-S395-2 symbiont co-culture system achieved significantly improved photosynthetic rates, biomass growth, and treatment effects. Under the optimal treatment conditions, the organic matter and nutrient removal rates were 81.06% ± 7.06% for chemical oxygen demand, 82.32% ± 7.18% for total nitrogen, and 82.98% ± 7.26% for total phosphorus. In addition, the rate of CO2 removal from biogas was 63.38% ± 5.35%. PRACTITIONER POINTS: The red and blue light intensity ratio of 5:5 showed the best removal performance. C. vulgaris-G. lucidum-S395-2 system obtained the best photosynthetic performance. The carbonic anhydrase activity had positive effects on CO2 removal performance.

Fungal Contamination in Microalgal Cultivation: Biological and Biotechnological Aspects of Fungi-Microalgae Interaction

In the last few decades, the increasing interest in microalgae as sources of new biomolecules and environmental remediators stimulated scientists’ investigations and industrial applications. Nowadays, microalgae are exploited in different fields such as cosmeceuticals, nutraceuticals and as human and animal food supplements. Microalgae can be grown using various cultivation systems depending on their final application. One of the main problems in microalgae cultivations is the possible presence of biological contaminants. Fungi, among the main contaminants in microalgal cultures, are able to influence the production and quality of biomass significantly. Here, we describe fungal contamination considering both shortcomings and benefits of fungi-microalgae interactions, highlighting the biological aspects of this interaction and the possible biotechnological applications.

One-step co-cultivation and flocculation of microalgae with filamentous fungi to valorize starch wastewater into high-value biomass

A novel method of one-step co-cultivation and harvesting of microalgae and fungi, for efficient starch wastewater treatment and high-value biomass production was developed. By combination of Aspergillus oryzae and Chlorella pyrenoidosa, nutrients in wastewater could be converted to useful microbial biomass, while the wastewater was purified. Moreover, the microalgae C. pyrenoidosa could gradually be encapsulated in fungal pellets which promoted the biomass harvesting. The free algal cells could be completely harvested by fungal pellets within 72 h. The synergistic effects between them greatly improved the removal efficiencies of main pollutants as the removal efficiency of COD, TN, and TP reached 92.08, 83.56, and 96.58 %, respectively. In addition, the final biomass concentration was higher than that of individual cultures. The protein and lipid concentration was also significantly improved and reached 1.92 and 0.99 g/L, respectively. This study provides a simple and efficient strategy for simultaneous wastewater treatment and high-value biomass production.

Synergism and mutualistic interactions between microalgae and fungi in fungi-microalgae symbiotic system

The method of collecting microalgae using fungal mycelium pellets has attracted widespread attention because of its high efficiency and simplicity. In this study, the interaction in FMSS was explored using Aspergillus fumigatus and Synechocystis sp. PCC6803. Under the conditions of 25-30 °C, pH of 5.0, 160 rpm, a light intensity of 1000 lx, light to darkness ratio of 6:18 h, and glucose concentration of 1.5 g/L, the FMSS had the highest biomass and recovery efficiency. SEM, TEM, and Zeta analysis showed that microalgae can be fixed on the surface of fungal mycelium pellets by the electrostatic attraction (amino, amide, phosphate, hydroxyl, and aldehyde groups) of EPS. The N cycling and CO₂-O₂ cycling promoted the synthesis of amino acids and provided a guarantee for gas exchange, and the intermediate metabolites (CO₃^2- and HCO₃^-/H₂CO₃) satisfied the metabolic activities. The microalgae and fungi worked in coordination each other, which was the mutualistic symbiosis.

Microalgae-Based Biorefineries: Challenges and Future Trends to Produce Carbohydrate Enriched Biomass, High-Added Value Products and Bioactive Compounds

Simple Summary

Microalgae-based biorefineries allow the simultaneous production of microalgae biomass enriched in a particular macromolecule and high-added and low-value products if a proper selection of the microalgae species and the cultivation conditions are adequate for the purpose. This review discusses the challenges and future trends related to microalgae-based biorefineries stressing the multi-product approach and the use of raw wastewater or pretreated wastewater to improve the cost-benefit ratio of biomass and products. Emphasis is given to the production of biomass enriched in carbohydrates. Microalgae-bioactive compounds as potential therapeutical and health promoters are also discussed. Future and novel trends following the circular economy strategy are also discussed.

Abstract

Microalgae have demonstrated a large potential in biotechnology as a source of various macromolecules (proteins, carbohydrates, and lipids) and high-added value products (pigments, poly-unsaturated fatty acids, peptides, exo-polysaccharides, etc.). The production of biomass at a large scale becomes more economically feasible when it is part of a biorefinery designed within the circular economy concept. Thus, the aim of this critical review is to highlight and discuss challenges and future trends related to the multi-product microalgae-based biorefineries, including both phototrophic and mixotrophic cultures treating wastewater and the recovery of biomass as a source of valuable macromolecules and high-added and low-value products (biofertilizers and biostimulants). The therapeutic properties of some microalgae-bioactive compounds are also discussed. Novel trends such as the screening of species for antimicrobial compounds, the production of bioplastics using wastewater, the circular economy strategy, and the need for more Life Cycle Assessment studies (LCA) are suggested as some of the future research lines.

A review on mycelial pellets as biological carriers: Wastewater treatment and recovery for resource and energy

Mycelial pellets, a new environment friendly biological carrier, have received wide attention from researchers due to porosity, stability and unique biocompatibility. In this article, the theoretical basis and mechanism of mycelial pellets as a biological carrier were analyzed from the properties of mycelial pellets and the interaction between mycelial pellets and other microorganisms. This article aims to collate and present the current application and development trend of mycelial pellets as biological carriers in wastewater treatment, resource and energy recovery, especially the symbiotic particle system formed by mycelial pellets and microalgae is an important way to break through the technical bottleneck of biodiesel recovery from wastewater. This review also analyzes the research hotspots and trends of mycelial pellets as carriers in recent years, discusses the challenges faced by this technology, and puts forward corresponding solutions.

Organic wastes bioremediation and its changing prospects

Increasing inappropriate anthropogenic activities and industrialization have resulted in severe environmental pollution worldwide. Their effective treatment is vital for general health concerns. Depending on the characteristics of pollutants, the severity of pollution may differ. For sustainable treatment of polluted environments, bioremediation is accepted as the most efficient, economical, and environmentally friendly method hence largely preferred. However, every bioremediation technique has its own unique advantages and limitations due to its defined applications criteria. In bioremediation, microorganisms play a decisive role in detoxification by degrading, mineralizing and accumulating various forms of harmful and biodegradable pollutants from the surroundings and transforming them into less lethal forms. Bioremediation is performed ex-situ or in-situ, based on location of polluted site as well as characteristics, type and strength of the pollutants. Furthermore, the most popular methodologies for bioremediation include bioaugmentation, biostimulation, bioattenuation among others which depend on the prevailing environmental factors into the microbial system. Implementing them appropriately and effectively under ex-situ or in-situ method is extremely important not only for obtaining efficient treatment but also for the best economic, environmental, and social impacts. Therefore, this review aims to analyze various bioremediation methods for organic pollutants remediation from soil/sediments and wastewater, their strength, limitation, and insights for the selection of appropriate bioremediation techniques based on nature, types, degree, and location of the pollution. The novelty aspect of the article is to give updates on several key supporting technologies which have recently emerged and exhibited great potential to enhance the present bioremediation efficiency such as nanobubble, engineered biochar, mixotrophic microalgae, nanotechnology etc. Moreover, amalgamation of these technologies with existing bioremediation facilities are significantly changing the scenario and scope of environmental remediation towards sustainable bioremediation.

Performance of different microalgae-fungi-bacteria co-culture technologies in photosynthetic and removal performance in response to various GR24 concentrations

The purification effect of two different microalgae-fungi-bacteria symbiosis technologies on biogas and biogas slurry was studied to determine the best symbiosis treatment technology and the suitable concentration of GR24. The results showed that the purification effect of biogas slurry in Chlorella vulgaris-Ganoderma lucidum-endophytic bacteria (S395-2) symbiont co-culture system was better than that of the biogas slurry in Scenedesmus obliquus-Pleurotus ostreatus-S395-2 symbionts. Following 10^-9 M GR24 treatment, Chlorella vulgaris-Ganoderma lucidum-S395-2 symbionts had elevated mean daily production rate and growth rate by 1.92 and 1.46 folds in comparison with blank group. After adjusting the GR24 level within the range of 10^-9 M-10^-7 M, Ganoderma lucidum-assisted Chlorella vulgaris-S395-2 attained higher maximal removal rates for TN, COD, CO₂, and TP by 10.78%, 14.62%, 3.86%, and 9.07%, respectively, compared to the rates when GR24 was not added.