Electrochemical Deposition of Copper on Bioactive Porous Titanium Dioxide Layer: Antibacterial and Pro-Osteogenic Activities

Ti surfaces must exhibit antibacterial activity without cytotoxicity to promote bone reconstruction and prevent infection simultaneously. In this study, we employed a two-step electrochemical treatment process, namely, microarc oxidation (MAO) and cathodic electrochemical deposition (CED), to modify Ti surfaces. During the MAO step, a porous TiO2 (pTiO2) layer with a surface roughness of approximately 2.0 μm was generated on the Ti surface, and in the CED step, Cu was deposited onto the pTiO2 layer on the Ti surface, forming Cu@pTiO2. Cu@pTiO2 exhibited a similar structure, adhesion strength, and crystal phase to pTiO2. Moreover, X-ray photoelectron spectroscopy (XPS) confirmed the presence of Cu in Cu@pTiO2 at an approximate concentration of 1.0 atom %. Cu@pTiO2 demonstrated a sustained release of Cu ions for a minimum of 28 days in a simulated in vivo environment. In vitro experiments revealed that Cu@pTiO2 effectively eradicated approximately 99% of Staphylococcus aureus and Escherichia coli and inhibited biofilm formation, in contrast to the Ti and pTiO2 surfaces. Moreover, Cu@pTiO2 supported the proliferation of osteoblast-like cells at a rate comparable to that observed on the Ti and pTiO2 surfaces. Similar to pTiO2, Cu@pTiO2 promoted the calcification of osteoblast-like cells compared with Ti. In summary, we successfully conferred antibacterial and pro-osteogenic activities to Ti surfaces without inducing cytotoxic effects or structural and mechanical alterations in pTiO2 through the application of MAO and CED processes. Moreover, we found that the pTiO2 layer promoted bacterial growth and biofilm formation more effectively than the Ti surface, highlighting the potential drawbacks of rough and porous surfaces. Our findings provide fundamental insights into the surface design of Ti-based medical devices for bone reconstruction and infection prevention.

Toward the Development of Simplified Lateral Flow Assays Using Hydrogels as the Universal Control Line

Lateral flow assays (LFA) have been widely utilized as point-of-care testing devices in diverse fields. However, it is imperative to preprint costly bioreceptors onto the lateral flow nitrocellulose membrane at the control line. The complex manufacturing process and relatively limited detection capabilities of LFA have impeded their utilization in more challenging fields. Here, we propose a novel and simple strategy to simplify the manufacture of LFA while simultaneously improving the sensitivity by modifying the hydrogel line (HL). In our study, it was observed that the sensitivity of commercial LFA strips could be enhanced by 2-5-fold by incorporating an extra HL. Particularly, a universal control line was developed to accommodate multiple LFA detection modes by substituting the conventional antibody control line with a hydrogel control line (HCL). As a proof of concept, the HCL performance could be associated with the slowdown and interception effect toward fluid, which are dependent on the permeation and hydrophilicity of the hydrogel with varying concentrations in the nitrocellulose membrane. This new design builds the foundation to enhance the sensitivity and develop the simplified LFA sensing platform without additional complicated processes.

Surface-Engineered Nanomaterials for Optical Array Based Sensing

Array based sensing governed by optical methods provides fast and economic way for detection of wide variety of analytes where the ideality of detection processes depends on the sensor element's versatile mode of interaction with multiple analytes in an unbiased manner. This can be achieved by either the receptor unit having multiple recognition moiety, or their surface property should possess tuning ability upon fabrication called surface engineering. Nanomaterials have a high surface to volume ratio, making them viable candidates for molecule recognition through surface adsorption phenomena, which makes it ideal to meet the above requirements. Most crucially, by engineering a nanomaterial's surface, one may produce cross-reactive responses for a variety of analytes while focusing solely on a single nanomaterial. Depending on the nature of receptor elements, in the last decade the array-based sensing has been considering as multimodal detection platform which operates through various pathway including single channel, multichannel, binding and indicator displacement assay, sequential ON-OFF sensing, enzyme amplified and nanozyme based sensing etc. In this review we will deliver the working principle for Array-based sensing by using various nanomaterials like nanoparticles, nanosheets, nanodots and self-assembled nanomaterials and their surface functionality for suitable molecular recognition.

Poly(ethylene glycol) Hydrogels with the Sustained Release of Hepatocyte Growth Factor for Enhancing Vascular Regeneration

The surface modification of biologically active factors on tissue-engineering vascular scaffold fails to fulfill the mechanical property and bioactive compounds' sustained release in vivo and results in the inhibition of tissue regeneration of small-diameter vascular grafts in vascular replacement therapies. In this study, biodegradable poly(ε-caprolactone) (PCL) was applied for scaffold preparation, and poly(ethylene glycol) (PG) hydrogel was used to load heparin and hepatocyte growth factor (HGF). In vitro analysis demonstrated that the PCL scaffold could inhibit the heparin release from the PG hydrogel, and the PG hydrogel could inhibit heparin release during the process of PCL degradation. Finally, it results in sustained release of HGF and heparin from the PCL-PG-HGF scaffold. The mechanical property of this hybrid scaffold improved after being coated with the PG hydrogel. In addition, the PCL-PG-HGF scaffold illustrated no inflammatory lesions, organ damage, or biological toxicity in all primary organs, with rapid organization of the endothelial cell layer, smooth muscle regeneration, and extracellular matrix formation. These results indicated that the PCL-PG-HGF scaffold is biocompatible and provides a microenvironment in which a tissue-engineered vascular graft with anticoagulant properties allows regeneration of vascular tissue (Scheme 1). Such findings confirm the feasibility of creating hydrogel scaffolds coated with bioactive factors to prepare novel vascular grafts.

Comparative Effects of Hydrazine and Thermal Reduction Methods on Electromagnetic Interference Shielding Characteristics in Foamed Titanium Carbonitride MXene Films

The urgent need for the development of micro-thin shields against electromagnetic interference (EMI) has sparked interest in MXene materials owing to their metallic electrical conductivity and ease of film processing. Meanwhile, postprocessing treatments can potentially exert profound impacts on their shielding effectiveness (SE). This work comprehensively compares two reduction methods, hydrazine versus thermal, to fabricate foamed titanium carbonitride (Ti3 CNTx ) MXene films for efficient EMI shielding. Upon treatment of ≈ 100 µm-thick MXene films, gaseous transformations of oxygen-containing surface groups induce highly porous structures (up to ≈ 74.0% porosity). The controlled application of hydrazine and heat allows precise regulation of the reduction processes, enabling tailored control over the morphology, thickness, chemistry, and electrical properties of the MXene films. Accordingly, the EMI SE values are theoretically and experimentally determined. The treated MXene films exhibit significantly enhanced SE values compared to the pristine MXene film (≈ 52.2 dB), with ≈ 38% and ≈ 83% maximum improvements for the hydrazine and heat-treated samples, respectively. Particularly, heat treatment is more effective in terms of this enhancement such that an SE of 118.4 dB is achieved at 14.3 GHz, unprecedented for synthetic materials. Overall, the findings of this work hold significant practical implications for advancing high-performance, non-metallic EMI shielding materials.

Surface-Initiated PET-RAFT via the Z-Group Approach

Surface-initiated reversible addition-fragmentation chain transfer (SI-RAFT) is a user-friendly and versatile approach for polymer brush engineering. For SI-RAFT, synthetic strategies follow either surface-anchoring of radical initiators (e.g., azo compounds) or anchoring RAFT chain transfer agents (CTAs) onto a substrate. The latter can be performed via the R-group or Z-group of the CTA, with the previous scientific focus in literature skewed heavily toward work on the R-group approach. This contribution investigates the alternative: a Z-group approach toward light-mediated SI photoinduced electron transfer RAFT (SI-PET-RAFT) polymerization. An appropriate RAFT CTA is synthesized, immobilized onto SiO2, and its ability to control the growth (and chain extension) of polymer brushes in both organic and aqueous environments is investigated with different acrylamide and methacrylate monomers. O2 tolerance allows Z-group SI-PET-RAFT to be performed under ambient conditions, and patterning surfaces through photolithography is illustrated. Polymer brushes are characterized via X-ray photoelectron spectroscopy (XPS), ellipsometry, and water contact angle measurements. An examination of polymer brush grafting density showed variation from 0.01 to 0.16 chains nm-2. Notably, in contrast to the R-group SI-RAFT approach, this chemical approach allows the growth of intermittent layers of polymer brushes underneath the top layer without changing the properties of the outermost surface.

Material and Design Toolkit for Drug Delivery: State of the Art, Trends, and Challenges

The nanomaterial and related toolkit have promising applications for improving human health and well-being. Nanobased drug delivery systems use nanoscale materials as carriers to deliver therapeutic agents in a targeted and controlled manner, and they have shown potential to address issues associated with conventional drug delivery systems. They offer benefits for treating various illnesses by encapsulating or conjugating biological agents, chemotherapeutic drugs, and immunotherapeutic agents. The potential applications of this technology are vast; however, significant challenges exist to overcome such as safety issues, toxicity, efficacy, and insufficient capacity. This article discusses the latest developments in drug delivery systems, including drug release mechanisms, material toolkits, related design molecules, and parameters. The concluding section examines the limitations and provides insights into future possibilities.

Resonant Magnetoelectric Coupling of Fe-Si-B/Pb(Zr,Ti)O3 Laminated Composites with Surface Crystalline Layers

The resonant magnetoelectric (ME) effect of Fe78Si9B13/Pb(Zr,Ti)O3 (FeSiB/PZT) composites with a surface-modified Fe78Si9B13 amorphous alloy has been studied. The surface-modified FeSiB can improve the ME coefficient at the resonant frequency by optimizing the magnetomechancial power conversion efficiency. The maximum ME coefficient of the surface-modified ribbons combined with soft PZT (PZT5) is two-thirds larger than that of the composites with fully amorphous ribbons. Meanwhile, the maximum value of the ME coefficient with surface-modified FeSiB ribbons and hard PZT (PZT8) is one-third higher compared with the fully amorphous composites. In addition, experimental results of magnetomechanical coupling properties of FeSiB/PZT composites with or without piezoelectric layers indicate that the power efficiency of the composites first decreases and then increases with the increase in the number of FeSiB layers. When the surface crystalline FeSiB ribbons are combined with a commercially available hard piezoelectric ceramic plate, the maximum magnetoelectric coupling coefficient of the ME composite reaches 5522 V/(Oe*cm), of which the electromechanical resonant frequency is 23.89 kHz.

Monodentate versus Bidentate Anchoring Groups in Self-Assembling Molecules (SAMs) for Robust p-i-n Perovskite Solar Cells

Current improvement in perovskite solar cells (PSCs) has been achieved by interface engineering and fine-tuning of charge-selective contacts. In this work, we report three novel molecules that can form self-assembled layers (SAMs) as an alternative to the most commonly used p-type contact material, PTAA. Two of these molecules have bidentate anchoring groups (MC-54 and MC-55), while the last one is monodentate (MC-45). Besides the PTAA comparison, we also compared those two types of molecules and their effect on the solar cell's performance. Devices fabricated with MC-54 and MC-55 showed a remarkable field factor (about 80%) and a better current density, leading to higher efficient solar cells in comparison to MC-45 and PTAA. Moreover, mono- and bidentate present higher stability and reproducibility in comparison to PTAA.

Enhancing the Performance of Reversible Zn Deposition by Ultrathin Polyelectrolyte Coatings

Modifying the surfaces of zinc and other metallic substrates is considered an effective strategy to enhance the reversibility of the zinc deposition and stripping processes. While a variety of surface modification strategies have been explored, their ability to be practically implemented is not always trivial due to the associated high costs and complexity of the proposed techniques. In this study, we showcase a straightforward method for preparing ultrathin polyelectrolyte coatings using polydiallyldimethylammonium chloride (PDDA) and polyethylenimine (PEI). The coatings, characterized by their electrostatic charge and hydrophobicity, suppress side reactions and even out the electrodeposition process across the substrate surface. The PDDA-coated anodes demonstrate significantly reduced voltage hysteresis, uniform zinc morphology, improved self-discharge rates, and an impressive Coulombic efficiency exceeding 99% over prolonged cycling. Our findings highlight the potential that such cost-effective and straightforward surface treatments could be widely applied in Zn metal-based batteries.

Association Between Surface Modifications for Biologic Fixation and Aseptic Loosening of Uncemented Total Knee Arthroplasties

BACKGROUND

Various surface modifications are used in uncemented total knee arthroplasties (TKAs) to enhance bony ingrowth and longevity of implants. This study aimed to identify which surface modifications are used, whether they are associated with different revision rates for aseptic loosening, and which are underperforming compared to cemented implants.

METHODS

Data on all cemented and uncemented TKAs used between 2007 and 2021 were obtained from the Dutch Arthroplasty Register. Uncemented TKAs were divided into groups based on their surface modifications. Revision rates for aseptic loosening and major revisions were compared between groups. Kaplan-Meier, Competing-Risk, Log-rank tests, and Cox regression analyses were used. In total, 235,500 cemented and 10,749 uncemented primary TKAs were included. The different uncemented TKA groups included the following: 1,140 porous-hydroxyapatite (HA); 8,450 Porous-uncoated; 702 Grit-blasted-uncoated; and 172 Grit-blasted-Titanium-nitride (TiN) implants.

RESULTS

The 10-year revision rates for aseptic loosening and major revision of the cemented TKAs were 1.3 and 3.1%, and for uncemented TKAs 0.2 and 2.3% (porous-HA), 1.3 and 2.9% (porous-uncoated), 2.8 and 4.0% (grit-blasted-uncoated), and 7.9% and 17.4% (grit-blasted-TiN), respectively. Both type of revision rates varied significantly between the uncemented groups (log-rank tests, P < .001, P < .001). All grit-blasted implants had a significantly higher risk of aseptic loosening (P < .01), and porous-uncoated implants had a significantly lower risk of aseptic loosening than cemented implants (P = .03) after 10 years.

CONCLUSION

There were 4 main uncemented surface modifications identified, with different revision rates for aseptic loosening. Implants with porous-HA and porous-uncoated had the best revision rates, at least equal to cemented TKAs. Grit-blasted implants with and without TiN underperformed, possibly due to the interaction of other factors.

Current Strategies of Surface Modifications to Polyurethane Biomaterials for Vascular Grafts

As the number of patients suffering from cardiovascular diseases and peripheral vascular diseases rises, the constraints of autologous transplantation remain unavoidable. As a result, artificial vascular grafts must be developed. Adhesion of proteins, platelets and bacteria on implants can result in stenosis, thrombus formation, and postoperative infection, which can be fatal for an implantation. Polyurethane, as a commonly used biomaterial, has been modified in various ways to deal with the adhesions of proteins, platelets, and bacteria and to stimulate endothelium adhesion. In this review, we briefly summarize the mechanisms behind adhesions, overview the current strategies of surface modifications of polyurethane biomaterials used in vascular grafts, and highlight the challenges that need to be addressed in future studies, aiming to gain a more profound understanding of how to develop artificial polyurethane vascular grafts with an enhanced implantation success rate and reduced side effect.

Enhancement of protein immobilization on polydimethylsiloxane using a synergistic combination of polydopamine and micropattern surface modification

Understanding protein interactions at biointerfaces is critical for the improved design of biomaterials and medical devices. Polydimethylsiloxane (PDMS) is used for numerous device applications, and surface modifications can enhance protein immobilization and the response to cells. A multifunctional approach combining topographical and biochemical modifications was applied to PDMS by fabricating 10-20 µm scale patterns onto PDMS surfaces and by coating with polydopamine (PDA). The modifications were confirmed by surface characterization and bovine serum albumin (BSA), fibrinogen (Fg), and fetuin-A (Fet-A) were radiolabeled with 125I. The amounts of protein attached to the surface before and after elution with sodium dodecyl sulfate (SDS) were quantified from single and complex multi-protein solutions to determine protein stability and competitive binding. The PDA coatings were the most stable and capable of immobilizing the highest levels of all proteins. Furthermore, combinations of PDA coatings with the smallest micropatterns provided an additional improvement, enhancing the amount immobilized and the stability. The adsorption of BSA and Fg from plasma demonstrated competitive binding and possible orientation changes, respectively. It was determined that Fet-A, a less studied protein, adsorbed from plasma at low levels, but the adsorption from fetal bovine serum (FBS) was significantly greater, providing important quantification data from radiolabeling that is relevant to many cell culture studies. Overall, combining topography and PDA modification has a synergistic effect on improving protein immobilization. These findings provide new insight on the quantities of proteins bound to PDMS and PDA coatings with implications for cell interactions in various biotechnology and medical applications.

Application of graphene oxide in tumor targeting and tumor therapy

Graphene oxide (GO), as a kind of two-dimensional sp2 carbon nanomaterials, has attracted great attention in many fields in the past decade. Due to its unique physical and chemical properties, GO is showing great promise in the field of biomedicine. For GO, all the atoms on its surface are exposed to the surface with ultra-high specific surface area, and a variety of groups on the surface, such as carboxyl, hydroxyl and epoxy groups, can effectively bind/load various biomolecules. Due to the availability of these groups, GO also possesses excellent hydrophilicity and biocompatibility for the modification of the desired biocompatible molecules or polymers on the surface of GO. The nano-network structure and hydrophobicity of GO enable it to load a large number of hydrophobic drugs containing benzene rings and it has been widely used as a multi-functional nano-carrier for chemotherapeutic drug or gene delivery. This review article will give an in-depth overview of the synthesis methods of GO, the advantages and disadvantages of GO used in nano-drug delivery system, the research progress of GO as a stimulus-responsive nano-drug carrier, and the application of these intelligent systems in cancer treatment.

Tunable Ga2O3 solar-blind photosensing performance via thermal reorder engineering and energy-band modulation

As an ultra-wide bandgap semiconductor, gallium oxide (Ga2O3) has been extensively applied in solar-blind photodetectors owing to the absorbance cut-off wavelength of shorter than 280 nm, and the optimized technologies of detection performance is seriously essential for its further usages. Herein, a feasible thermal reorder engineering method was performed through annealing Ga2O3 films in vacuum, O2 and oxygen plasma atmospheres, realizing to tune solar-blind photosensing performance of Ga2O3 photodetectors. Thermal treatment, in fact a crystal reorder process, significantly suppressed the noise in Ga2O3-based photodetectors and enhanced the photo-sensitivity, with the dark current decreasing from 154.63 pA to 269 fA and photo-to-dark current ratio magically raising from 288 to 2.85×104. This achievement is dependent of energy-band modulation in Ga2O3 semiconductor, that is certified by first-principles calculation. Additionally, annealing in oxygen atmospheres notably reduces the concentration of oxygen vacancies in the surface of films, thereby improving the performance of the photodetectors; the oxygen vacancy is extremely concerned in oxide semiconductors in the view of physics of surface defects. In all, this work could display a promising guidance for modulating the performance of photodetectors based on wide bandgap oxide semiconductor, especially for hot Ga2O3 issue. .

Strong Room-Temperature Ferromagnetism in Ultrathin NiOOH Nanosheets through Surfactant Manipulation

Two-dimensional (2D) ferromagnetic (FM) materials with nanoscale thickness and spontaneous net magnetization have emerged as a promising class of functional materials for applications in next-generation spintronics, quantum processing, and data storage devices. However, most 2D materials exhibit weak FM even at low temperatures, limiting their potential applications in many technological fields. The fabrication of strong room-temperature FM 2D materials is highly desirable for the development of practical applications. Here, we demonstrate an ionic layer epitaxy strategy to synthesize few-layered NiOOH nanosheets with strong room-temperature FM and a saturation magnetization up to 409.86 emu cm-3 at 300 K. The results are consistent with the ab initio predictions of a stable FM NiOOH nanolayer structure with an FM configuration. The FM strength of the NiOOH nanosheets can be tuned by controlling the surfactant monolayer density and annealing. This work offers a promising strategy for achieving strong high-temperature FM in 2D materials for spintronic applications.

Oligohexamethylene Guanidine Derivative as a Means to Prevent Biological Fouling of a Polymer-Based Composite Optical Oxygen Sensor

The use of biocidal agents is a common practice for protection against biofouling in biomass-rich environments. In this paper, oligohexamethyleneguanidine (OHMG) polymer, known for its biocidal properties, was further modified with para-aminosalicylic acid (PAS) to enhance its properties against microorganisms coated with a lipid membrane. The structure of the product was confirmed by 1H NMR, 13C NMR, and FTIR spectroscopy. The values of the minimum inhibitory concentration (MIC) against Mycobacterium smegmatis ATCC 607 and Pseudomonas chlororaphis 449 were found to be 1.40 and 1.05 μg/mL, respectively. The synthesized substance was used as an additive to the polymer matrix of the composite optical oxygen sensor material. A series of samples with different contents of OHMG-PAS was prepared using a co-dissolution method implying the fabrication of a coating from a solution containing both polymers. It turned out that the mutual influence of the components significantly affects the distribution of the indicator in the matrix, surface morphology, and contact angle. The optimal polymer content turned out to be wt.3%, at which point the water contact angle reaches almost 122°, and the fouling rate decreases by almost five times, which is confirmed by both the respiratory MTT assay and confocal microscopy with staining. This opens up prospects for creating stable and biofouling-resistant sensor elements for use in air tanks or seawater.

Enhanced Adsorption of Textile Dyes by a Novel Sulfonated Activated Carbon Derived from Pomegranate Peel Waste: Isotherm, Kinetic and Thermodynamic Study

The rapid growth of the dye and textile industry has raised significant public concerns regarding the pollution caused by dye wastewater, which poses potential risks to human health. In this study, we successfully improved the adsorption efficiency of activated carbon derived from pomegranate peel waste (PPAC) through a single-step and surface modification approach using 5-sulfonate-salicylaldehyde sodium salt. This innovative and effective sulfonation approach to produce sulfonated activated carbon (S-PPAC) proved to be highly effective in removing crystal violet dye (CV) from polluted water. The prepared PPAC and S-PPAC were characterized via FESEM, EDS, FTIR and BET surface area. Characterization studies confirmed the highly porous structure of the PPAC and its successful surface modification, with surface areas reaching 1180.63 m2/g and 740.75 m2/g for the PPAC and S-PPAC, respectively. The maximum adsorption capacity was achieved at 785.53 mg/g with the S-PPAC, an increase of 22.76% compared to the PPAC at 45 °C. The isothermic adsorption and kinetic studies demonstrated that the adsorption process aligned well with the Freundlich isotherm model and followed the Elovich kinetic model, respectively. The thermodynamic study confirmed that the adsorption of CV dye was endothermic, spontaneous and thermodynamically favorable onto PPAC and S-PPAC.

Surface Modification Functionalized Carbon Dots

Carbon dots (CDs) smaller than 10 nm constitute a new type of fluorescent carbon-based nanomaterial. They have attracted much attention owing to their unique structures and excellent photoelectric properties. Primitive CDs usually comprise carbon and oxygen and are synthesized in one step from various natural products or synthetic organic compounds, usually via microwave or hydrothermal methods. However, the uniformity of surface functional groups often make CDs lack the diversity of active sites required for specific applications. Therefore, the functionalization of CDs by specific groups is a powerful strategy for improving their photophysical and photochemical properties. This paper reviews surface modification strategies to overcome these shortcomings. Functionalizing CDs using covalent or non-covalent modification can give them unique properties and broaden their applicability.

In Vitro/In Vivo Preparation and Evaluation of cRGDyK Peptide-Modified Polydopamine-Bridged Paclitaxel-Loaded Nanoparticles

Cancer remains a disease with one of the highest mortality rates worldwide. The poor water solubility and tissue selectivity of commonly used chemotherapeutic agents contribute to their poor efficacy and serious adverse effects. This study proposes an alternative to the traditional physicochemically combined modifications used to develop targeted drug delivery systems, involving a simpler surface modification strategy. cRGDyK peptide (RGD)-modified PLGA nanoparticles (NPs) loaded with paclitaxel were constructed by coating the NP surfaces with polydopamine (PD). The average particle size of the produced NPs was 137.6 ± 2.9 nm, with an encapsulation rate of over 80%. In vitro release tests showed that the NPs had pH-responsive drug release properties. Cellular uptake experiments showed that the uptake of modified NPs by tumor cells was significantly better than that of unmodified NPs. A tumor cytotoxicity assay demonstrated that the modified NPs had a lower IC50 and greater cytotoxicity than those of unmodified NPs and commercially available paclitaxel formulations. An in vitro cytotoxicity study indicated good biosafety. A tumor model in female BALB/c rats was established using murine-derived breast cancer 4T1 cells. RGD-modified NPs had the highest tumor-weight suppression rate, which was higher than that of the commercially available formulation. PTX-PD-RGD-NPs can overcome the limitations of antitumor drugs, reduce drug toxicity, and increase efficacy, showing promising potential in cancer therapy.

Integrated Laser Additive Manufacturing of α-Al2O3 Nanoparticle-Seeded β/γ' Ni-Al Intermetallic Alloy with Enhanced High-Temperature Oxidation Performance

The oxidation of β-NiAl at high temperatures leads to the preferential formation of metastable alumina, such as θ-Al2O3, which exhibits a significantly faster growth rate compared to stable α-Al2O3. However, our recent research has shown that through the use of the surface-dispersing nanoparticles (NPs) of metal oxides with a hexagonal closed pack (hcp), such as α-Al2O3, the thermal growth of α-Al2O3 can be facilitated. The present study employed laser additive manufacturing (LAM) to develop an integrated α-Al2O3 NPs surface-seeded two-phase intermetallic alloy comprising brittle β-NiAl and tougher γ'-Ni3Al, which demonstrated better comprehensive mechanical properties. It was found that seeding the α-Al2O3 NPs promoted the early stage growth of α-Al2O3 on both β and γ' phases during oxidation in air at 1000 °C. This led to a decrease in the oxidation rate but an enhancement in adhesion of the formed alumina scale in comparison to the naked β/γ' two-phase alloy. The reasons for this result were interpreted.

Effects of Plasma Treatment on the Strength of Bonding to Ceramic Surfaces in Orthodontics-A Comprehensive Review

Over the past several decades, orthodontic treatment has been increasingly sought out by adults, many of whom have undergone restorative dental procedures that cover enamel. Because the characteristics of restorative materials differ from those of enamel, typical bonding techniques do not yield excellent restoration-bracket bonding strengths. Plasma treatment is an emerging surface treatment that could potentially improve bonding properties. The purpose of this paper is to evaluate currently available studies assessing the effect of plasma treatment on the shear bond strength (SBS) and failure mode of resin cement/composite on the surface of ceramic materials. PubMed and Google Scholar databases were searched for relevant studies, which were categorized by restorative material and plasma treatment types that were evaluated. It was determined that cold atmospheric plasma (CAP) treatment using helium and H2O gas was effective at raising the SBS of feldspathic porcelain to a bonding agent, while CAP treatment using helium gas might also be a potential treatment method for zirconia and other types of ceramics. More importantly, CAP treatment using helium has the potential for being carried out chairside due to its non-toxicity, low temperature, and short treatment time. However, because all the studies were conducted in vitro and not tested in an orthodontic setting, further research must be conducted to ascertain the effectiveness of specific plasma treatments in comparison to current orthodontic bonding treatments in vivo.

Adsorption Affinities of Small Volatile Organic Molecules on Graphene Surfaces for Novel Nanofiller Design: A DFT Study

The adsorption of organic molecules on graphene surfaces is a crucial process in many different research areas. Nano-sized carbon allotropes, such as graphene and carbon nanotubes, have shown promise as fillers due to their exceptional properties, including their large surface area, thermal and electrical conductivity, and potential for weight reduction. Surface modification methods, such as the "pyrrole methodology", have been explored to tailor the properties of carbon allotropes. In this theoretical work, an ab initio study based on Density Functional Theory is performed to investigate the adsorption process of small volatile organic molecules (such as pyrrole derivatives) on graphene surface. The effects of substituents, and different molecular species are examined to determine the influence of the aromatic ring or the substituent of pyrrole's aromatic ring on the adsorption energy. The number of atoms and presence of π electrons significantly influence the corresponding adsorption energy. Interestingly, pyrroles and cyclopentadienes are 10 kJ mol-1 more stable than the corresponding unsaturated ones. Pyrrole oxidized derivatives display more favorable supramolecular interactions with graphene surface. Intermolecular interactions affect the first step of the adsorption process and are important to better understand possible surface modifications for carbon allotropes and to design novel nanofillers in polymer composites.

Ex Vivo Peptide Decoration Strategies on Stem Cell Surfaces for Augmenting Endothelium Interaction

Ischemic vascular diseases remain leading causes of disability and death. Although various clinical therapies have been tried, reperfusion injury is a major issue, occurring when blood recirculates at the damaged lesion. As an alternative approach, cell-based therapy has emerged. Mesenchymal stem cells (MSCs) are attractive cellular candidates due to their therapeutic capacities, including differentiation, safety, angiogenesis, and tissue repair. However, low levels of receptors/ligands limit targeted migration of stem cells. Thus, it is important to improve homing efficacy of transplanted MSCs toward damaged endothelium. Among various MSC modulations, ex vivo cell surface engineering could effectively augment homing efficiency by decorating MSC surfaces with alternative receptors/ligands, thereby facilitating intercellular interactions with the endothelium. Especially, exogenous decoration of peptides onto stem cell surfaces could provide appropriate functional signaling moieties to achieve sufficient MSC homing. Based on their protein-like functionalities, high modularity in molecular design, and high specific affinities and multivalency to target receptors, peptides could be representative surface-presentable moieties. Moreover, peptides feature a mild synthetic process, enabling precise control of amino acid composition and sequence. Such ex vivo stem cell surface engineering could be achieved primarily by hydrophobic interactions of the cellular bilayer with peptide-conjugated anchor modules and by covalent conjugation between peptides and available compartments in membranes. To this end, this review provides an overview of currently available peptide-mediated, ex vivo stem cell surface engineering strategies for enhancing MSC homing efficiency by facilitating interactions with endothelial cells. Stem cell surface engineering techniques using peptide-based bioconjugates have the potential to revolutionize current vascular disease treatments while addressing their technical limitations.

Modification of titanium orthopedic implants with bioactive glass: a systematic review of in vivo and in vitro studies

Bioactive glasses (BGs) are ideal biomaterials in the field of bio-restoration due to their excellent biocompatibility. Titanium alloys are widely used as a bone graft substitute material because of their excellent corrosion resistance and mechanical properties; however, their biological inertness makes them prone to clinical failure. Surface modification of titanium alloys with bioactive glass can effectively combine the superior mechanical properties of the substrate with the biological properties of the coating material. In this review, the relevant articles published from 2013 to the present were searched in four databases, namely, Web of Science, PubMed, Embase, and Scopus, and after screening, 49 studies were included. We systematically reviewed the basic information and the study types of the included studies, which comprise in vitro experiments, animal tests, and clinical trials. In addition, we summarized the applied coating technologies, which include pulsed laser deposition (PLD), electrophoretic deposition, dip coating, and magnetron sputtering deposition. The superior biocompatibility of the materials in terms of cytotoxicity, cell activity, hemocompatibility, anti-inflammatory properties, bioactivity, and their good bioactivity in terms of osseointegration, osteogenesis, angiogenesis, and soft tissue adhesion are discussed. We also analyzed the advantages of the existing materials and the prospects for further research. Even though the current research status is not extensive enough, it is still believed that BG-coated Ti implants have great clinical application prospects.

Construction of functional surfaces for dental implants to enhance osseointegration

Dental implants have been extensively used in patients with defects or loss of dentition. However, the loss or failure of dental implants is still a critical problem in clinic. Therefore, many methods have been designed to enhance the osseointegration between the implants and native bone. Herein, the challenge and healing process of dental implant operation will be briefly introduced. Then, various surface modification methods and emerging biomaterials used to tune the properties of dental implants will be summarized comprehensively.

2D Nanomaterials and Their Drug Conjugates for Phototherapy and Magnetic Hyperthermia Therapy of Cancer and Infections

Photothermal therapy (PTT) and magnetic hyperthermia therapy (MHT) using 2D nanomaterials (2DnMat) have recently emerged as promising alternative treatments for cancer and bacterial infections, both important global health challenges. The present review intends to provide not only a comprehensive overview, but also an integrative approach of the state-of-the-art knowledge on 2DnMat for PTT and MHT of cancer and infections. High surface area, high extinction coefficient in near-infra-red (NIR) region, responsiveness to external stimuli like magnetic fields, and the endless possibilities of surface functionalization, make 2DnMat ideal platforms for PTT and MHT. Most of these materials are biocompatible with mammalian cells, presenting some cytotoxicity against bacteria. However, each material must be comprehensively characterized physiochemically and biologically, since small variations can have significant biological impact. Highly efficient and selective in vitro and in vivo PTTs for the treatment of cancer and infections are reported, using a wide range of 2DnMat concentrations and incubation times. MHT is described to be more effective against bacterial infections than against cancer therapy. Despite the promising results attained, some challenges remain, such as improving 2DnMat conjugation with drugs, understanding their in vivo biodegradation, and refining the evaluation criteria to measure PTT or MHT effects.

Rapid Surface Modification of Stainless Steel 304L Electrodes for Microbial Electrochemical Sensor Application

Electrogenic microorganisms serve as important biocatalysts for microbial electrochemical sensors (MESes). The electrical signal produced is based on the rate of electron transfer between the microbes and electrodes, which represents the biotoxicity of water. However, existing MESes require complex and sophisticated fabrication methods. Here, several low-cost and rapid surface modification strategies (carbon powder-coated, flame-oxidized, and acid-bleached) have been demonstrated and studied for biosensing purposes. Surface-modified MESe bioanodes were successfully applied to detect multiple model pollutants including sodium acetate, ethanol, thinner, and palm oil mill effluent under three different testing sequences, namely, pollutant incremental, pollutant dumping, and water dilution tests. The carbon powder-coated bioanode showed the most responsive signal profile for all the three tests, which is in line with the average roughness values (Ra) when tested with atomic force microscopy. The carbon powder-coated electrode possessed a Ra value of 0.844, while flame-oxidized, acid-bleached, and control samples recorded 0.323, 0.336, and 0.264, respectively. The higher roughness was caused by the carbon coating and provided adhesive sites for microbial attachment and growth. The accuracy of MESe was also verified by correlating with chemical oxygen demand (COD) results. Similar to the sensitivity test, the carbon powder-coated bioanode obtained the highest R2 value of 0.9754 when correlated with COD results, indicating a high potential of replacing conventional water quality analysis methods. The reported work is of great significance to showcase facile surface modification techniques for MESes, which are cost-effective and sustainable while retaining the biocompatibility toward the microbial community with carbon-based coatings.

Controlling Fluorescent Readout in Paper-based Analytical Devices

Paper is an ideal candidate for the development of new disposable diagnostic devices because it is a low-cost material, allows transport of the liquid on the device by capillary action, and is environmentally friendly. Today, colorimetric analysis is most often used as a detection method for rapid tests (test strips or lateral flow devices) but usually gives only qualitative results and is limited by a relatively high detection threshold. Here, we describe studies using fluorescence as a readout tool for paper-based diagnostics. We study how the optical readout is affected by light transmission, scattering, and fluorescence as a function of paper characteristics such as thickness (grammage), water content, autofluorescence, and paper type/composition. We show that paper-based fluorescence analysis allows better optical readout compared to that of nitrocellulose, which is currently the material of choice in colorimetric assays. To reduce the loss of analyte molecules (e.g., proteins) due to adsorption to the paper surface, we coat the paper fibers with a protein-repellent hydrogel. For this purpose, we use hydrophilic copolymers consisting of N,N-dimethyl acrylamide and a benzophenone-based cross-linker, which are photochemically transformed into a fiber-attached polymer hydrogel on the paper fiber surfaces in situ. We show that the combination of fluorescence detection and the use of a protein-repellent coating enables sensitive paper-based analysis. Finally, the success of the strategy is demonstrated by using a simple LFD application as an example.

Chitosan-salvianolic acid B coating on the surface of nickel-titanium alloy inhibits proliferation of smooth muscle cells and promote endothelialization

Introduction: Intracranial stents are of paramount importance in managing cerebrovascular disorders. Nevertheless, the currently employed drug-eluting stents, although effective in decreasing in-stent restenosis, might impede the re-endothelialization process within blood vessels, potentially leading to prolonged thrombosis development and restenosis over time. Methods: This study aims to construct a multifunctional bioactive coating to enhance the biocompatibility of the stents. Salvianolic acid B (SALB), a bioactive compound extracted from Salvia miltiorrhiza, exhibits potential for improving cardiovascular health. We utilized dopamine as the base and adhered chitosan-coated SALB microspheres onto nickel-titanium alloy flat plates, resulting in a multifunctional drug coating. Results: By encapsulating SALB within chitosan, the release period of SALB was effectively prolonged, as evidenced by the in vitro drug release curve showing sustained release over 28 days. The interaction between the drug coating and blood was examined through experiments on water contact angle, clotting time, and protein adsorption. Cellular experiments showed that the drug coating stimulates the proliferation, adhesion, and migration of human umbilical vein endothelial cells. Discussion: These findings indicate its potential to promote re-endothelialization. In addition, the bioactive coating effectively suppressed smooth muscle cells proliferation, adhesion, and migration, potentially reducing the occurrence of neointimal hyperplasia and restenosis. These findings emphasize the exceptional biocompatibility of the newly developed bioactive coating and demonstrate its potential clinical application as an innovative strategy to improve stent therapy efficacy. Thus, this coating holds great promise for the treatment of cerebrovascular disease.

Network-Polymer-Modified Superparamagnetic Magnetic Silica Nanoparticles for the Adsorption and Regeneration of Heavy Metal Ions

Superparamagnetic magnetic nanoparticles (MNPs, Fe3O4) were first synthesized based on a chemical co-precipitation method, and the core-shell magnetic silica nanoparticles (MSNPs, Fe3O4@SiO2) were obtained via hydrolysis and the condensation of tetraethyl orthosilicate onto Fe3O4 seed using a sol-gel process. Following that, MSNPs were immobilized using a three-step grafting strategy, where 8-hloroacetyl-aminoquinoline (CAAQ) was employed as a metal ion affinity ligand for trapping specific heavy metal ions, and a macromolecular polymer (polyethylenimine (PEI)) was selected as a bridge between the surface hydroxyl group and CAAQ to fabricate a network of organic networks onto the MSNPs' surface. The as-synthesized MSNPs-CAAQ nanocomposites possessed abundant active functional groups and thus contained excellent removal features for heavy metal ions. Specifically, the maximum adsorption capacities at room temperature and without adjusting pH were 324.7, 306.8, and 293.3 mg/g for Fe3+, Cu2+, and Cr3+ ions, respectively, according to Langmuir linear fitting. The adsorption-desorption experiment results indicated that Na2EDTA proved to be more suitable as a desorbing agent for Cr3+ desorption on the MSNPs-CAAQ surface than HCl and HNO3. MSNPs-CAAQ exhibited a satisfactory adsorption capacity toward Cr3+ ions even after six consecutive adsorption-desorption cycles; the adsorption efficiency for Cr3+ ions was still 88.8% with 0.1 mol/L Na2EDTA as the desorbing agent. Furthermore, the MSNPs-CAAQ nanosorbent displayed a strong magnetic response with a saturated magnetization of 24.0 emu/g, and they could be easily separated from the aqueous medium under the attraction of a magnet, which could facilitate the sustainable removal of Cr3+ ions in practical applications.

A "Win-Win" Strategy to Modify Co/C Foam with Carbon Microspheres for Enhanced Dielectric Loss and Microwave Absorption Characteristics

3D carbon foams have demonstrated their superiority in the field of microwave absorption recently, but the preparation processes of traditional graphene foams are complicated, while some novel carbon foams usually suffer from inadequate dielectric property. Herein, a simple "win-win" strategy is demonstrated to synchronously realize the construction of 3D Co/C foam and its surface decoration with carbon microspheres. Therein, the host Co/C foams and guest carbon microspheres interact with each other, resulting in the improvement of the dispersity of carbon microspheres and Co nanoparticles. The bilaterally synergistic effect can effectively enhance the interfacial polarization and conductive loss of these obtained samples. Electromagnetic analysis reveals that the optimized sample with moderate carbon microsphere content (about 33.5 wt%) displays a widened maximum effective absorption bandwidth of 5.2 GHz and a consolidated reflection loss intensity of -67.6 dB. Besides, the microwave absorption enhancement mechanisms are investigated and discussed in detail. It is believed that this work provides valuable ideas for the development of 3D-foam-based microwave absorbing materials for practical applications.

Efficient Adsorption of Ammonia by Surface-Modified Activated Carbon Fiber Mesh

In view of the characteristics and risks of ammonia, its removal is important for industrial production and environmental safety. In this study, viscose-based activated carbon fiber (ACF) was used as a substrate and chemically modified by nitric acid impregnation to enhance the adsorption capacity of the adsorbent for ammonia. A series of modified ACF-based adsorbents were prepared and characterized using BET, FTIR, XPS, and Boehm titration. Isotherm tests (293.15 K, 303.15 K, 313.15 K) and dynamic adsorption experiments were performed. The characterization results showed that impregnation with low concentrations of nitric acid not only increased the surface acidic functional group content but also increased the specific surface area, while impregnation with high concentrations of nitric acid could be able to decrease the specific surface area. ACF-N-6 significantly increased the surface functional group content without destroying the physical structure of the activated carbon fibers. The experimental results showed that the highest adsorption of ammonia by ACFs was 14.08 mmol-L-1 (ACF-N-6) at 293 K, and the adsorption capacity was increased by 165% compared with that of ACF-raw; by fitting the adsorption isotherm and calculating the equivalent heat of adsorption and thermodynamic parameters using the Langmuir-Freundlich model, the adsorption process could be found to exist simultaneously. Regarding physical adsorption and chemical adsorption, the results of the correlation analysis showed that the ammonia adsorption performance was strongly correlated with the carboxyl group content and positively correlated with the relative humidity (RH) of the inlet gas. This study contributes to the development of an efficient ammonia adsorption system with important applications in industrial production and environmental safety.

Cocontinuous Nanostructures by Microphase Separation of Statistically Cross-Linked Polystyrene/Poly(2-vinylpyridine) Networks

Cocontinuous polymeric nanostructures have drawn considerable attention due to their ability to combine distinct, percolation-dependent properties of two different polymer domains. Randomly end-linked copolymer networks (RECNs) have previously been shown to support the formation of disordered cocontinuous nanostructures across wide composition windows in a robust way. However, achieving highly efficient linking of telechelic polymers with excellent end-group fidelity often requires complex synthetic routes. As an alternative, we study here statistically cross-linked copolymer networks (SCCNs) composed of polystyrene and poly(2-vinylpyridine) (PS and P2VP) with cross-linkable allyl pendent groups that are conveniently synthesized by controlled radical copolymerization. Via selective extraction of P2VP, coupled with gravimetry, small-angle X-ray scattering, and electron microscopy, we find disordered cocontinuous phases across wide composition ranges (up to ≈ 35 wt %), approaching values previously determined for RECNs. Remarkably, even for samples that appear to exhibit full percolation, a substantial fraction of P2VP (≈ 20-30 wt %) cannot be removed, which we ascribe to short strands between nearby cross-linkers that are physically embedded within PS domains. The resulting PS porous monoliths with residual surface P2VP layers enable facile surface modification to resist protein adsorption and templating of porous gold nanostructures.

Surface immobilized α-1 acid glycoprotein and collagen VI modulate mouse macrophage polarization and reduce the foreign body capsule

Macrophages are widely recognized in modulating the foreign body response, and the manner in which they do so largely depends on their activation state, often referred to as their polarization. This preliminary study demonstrates that surface immobilized α-1 acid glycoprotein (AGP), as well as collagen VI (Col6) in conjunction with AGP, can direct macrophages towards the M2 polarization state in vitro and modify the foreign body response in vivo. AGP and Col6 are immobilized onto poly(2-hydroxyethyl methacrylate) (pHEMA) surfaces using carbonyl diimidazole chemistry. Mouse bone marrow derived macrophages are cultured on modified surfaces with or without lipopolysaccharide stimulation. Surface modified pHEMA discs are implanted subcutaneously into mice to observe differences in the foreign body response. After stimulation with lipopolysaccharide, macrophages cultured on AGP or Col6 modified surfaces showed a reduction in TNF-α expression compared to controls. Arg1 expression was also increased in macrophages cultured on modified surfaces. Explanted tissues showed that the foreign body capsule around implants with AGP or AGP and Col6 modification had reduced thickness, while also being more highly vascularized. These data demonstrate that α-1 acid glycoprotein and collagen VI could potentially be used for the surface modification of medical devices to influence macrophage polarization leading to a reduced and modulated foreign body response.

Graphene-Based Composites for Biomedical Applications: Surface Modification for Enhanced Antimicrobial Activity and Biocompatibility

The application of graphene-based materials in medicine has led to significant technological breakthroughs. The remarkable properties of these carbon materials and their potential for functionalization with various molecules and compounds make them highly attractive for numerous medical applications. To enhance their functionality and applicability, extensive research has been conducted on surface modification of graphene (GN) and its derivatives, including modifications with antimicrobials, metals, polymers, and natural compounds. This review aims to discuss recent and relevant studies related to advancements in the formulation of graphene composites, addressing their antimicrobial and/or antibiofilm properties and evaluating their biocompatibility, with a primary focus on their biomedical applications. It was concluded that GN surface modification, particularly with compounds intrinsically active against bacteria (e.g., antimicrobial peptides, silver and copper nanomaterials, and chitosan), has resulted in biomaterials with improved antimicrobial performance. Furthermore, the association of GN materials with non-natural polymers provides composites with increased biocompatibility when interfaced with human tissues, although with slightly lower antimicrobial efficacy. However, it is crucial to highlight that while modified GN materials hold huge potential, their widespread use in the medical field is still undergoing research and development. Comprehensive studies on safety, long-term effects, and stability are essential before their adoption in real-world medical scenarios.

Surface-Modified Electrospun Glass Nanofibers from Silane Treatment and Their Use for High-Performance Epoxy-Based Nanocomposite Materials

As a new and promising reinforcing filler, electrospun glass nanofibers (EGNFs) have attracted attention in the field of polymer composite materials. However, the reinforcing effectiveness of surface-modified EGNFs using different silane coupling agents in epoxy resin is still not quite clear. In this research, a series of silane coupling agents with increasing chain lengths in the order of methyl trimethoxysilane (MTMS), (3-aminopropyl) triethoxysilane (APTES), (3-glycidyloxypropyl) trimethoxysilane (GPTMS), and dual silane coupling agent APTES-GPTMS were employed to carry out surface treatment on the EGNFs. The pristine and silane functionalized EGNFs were then incorporated into epoxy resin as reinforcing fillers at low loading levels, i.e., 0.25 wt.%, 0.5 wt.%, and 1 wt.%, and the mechanical properties of the resultant epoxy nanocomposites, including strength, stiffness, ductility, and toughness, were evaluated. A commercial product of glass nanoparticles (GNPs) was used as a control to compare the reinforcing effectiveness of the EGNFs and the GNPs. This study revealed that the EGNFs could provide significant reinforcing and toughening effects at ultra-low loading (0.25 wt.%) in epoxy nanocomposite materials. Furthermore, surface modification of the EGNFs with silane coupling agents with long chain lengths, e.g., by using dual silane coupling agents, APTES-GPTMS, could enhance the interfacial bonding between the EGNFs and the epoxy matrix and further increase the mechanical performance of the EGNF-reinforced epoxy nanocomposite materials. Through this research, we realized epoxy nanocomposite materials with much-improved mechanical properties, i.e., 37%, 24%, 18%, 57% improvement in strength, stiffness, ductility, and toughness, respectively, with respect to those of the cured neat epoxy material with an ultra-low loading (0.25 wt.%) of APTES-GPTMS-EGNFs. Our research paves the road for developing lighter and stronger epoxy nanocomposite materials with EGNFs.

Research Progress on Low-Surface-Energy Antifouling Coatings for Ship Hulls: A Review

The adhesion of marine-fouling organisms to ships significantly increases the hull surface resistance and expedites hull material corrosion. This review delves into the marine biofouling mechanism on marine material surfaces, analyzing the fouling organism adhesion process on hull surfaces and common desorption methods. It highlights the crucial role played by surface energy in antifouling and drag reduction on hulls. The paper primarily concentrates on low-surface-energy antifouling coatings, such as organic silicon and organic fluorine, for ship hull antifouling and drag reduction. Furthermore, it explores the antifouling mechanisms of silicon-based and fluorine-based low-surface-energy antifouling coatings, elucidating their respective advantages and limitations in real-world applications. This review also investigates the antifouling effectiveness of bionic microstructures based on the self-cleaning abilities of natural organisms. It provides a thorough analysis of antifouling and drag reduction theories and preparation methods linked to marine organism surface microstructures, while also clarifying the relationship between microstructure surface antifouling and surface hydrophobicity. Furthermore, it reviews the impact of antibacterial agents, especially antibacterial peptides, on fouling organisms' adhesion to substrate surfaces and compares the differing effects of surface structure and substances on ship surface antifouling. The paper outlines the potential applications and future directions for low-surface-energy antifouling coating technology.

Surface-Modified Nano-Hydroxyapatite Uniformly Dispersed on High-Porous GelMA Scaffold Surfaces for Enhanced Osteochondral Regeneration

Purpose

This study aims to investigate the impact of enhancing subchondral bone repair on the efficacy of articular cartilage restoration, thereby achieving improved osteochondral regeneration outcomes.

Methods

In this study, we modified the surface of nano-hydroxyapatite (n-HAp) through alkylation reactions to prepare n-HApMA. Characterization techniques, including X-ray diffraction, infrared spectroscopy scanning, thermogravimetric analysis, particle size analysis, and electron microscopy, were employed to analyze n-HApMA. Bioinks were prepared using n-HApMA, high porosity GelMA hydrogel, and adipose tissue derived stromal cells (ADSCs). The rheological properties of the bioinks during photocuring were investigated using a rheometer. Based on these bioinks, a biphasic scaffold was constructed. The viability of cells within the scaffold was observed using live-dead cell staining, while the internal morphology was examined using scanning electron microscopy. The stiffness of the scaffold was evaluated through compression testing. Scaffolds were implanted into the osteochondral defects of New Zealand rabbit knees, and microCT was utilized to observe the subchondral bone repair. Hematoxylin and eosin (H&E) staining, Masson's trichrome staining, and Safranin O/Fast Green staining were performed to assess the regeneration of subchondral bone and cartilage. Furthermore, immunohistochemical staining was employed to detect the expression of osteogenic and chondrogenic-related molecules.

Results

Scaffold characterization revealed that surface modification enables the uniform distribution of n-HApMA within the GelMA matrix. The incorporation of 5% n-HApMA notably enhanced the elastic modulus and stiffness of the 6% high-porosity GelMA in comparison to n-HAp. Moreover, in-vivo study showed that the homogeneous dispersion of n-HApMA on the GelMA matrix facilitated the osteogenic differentiation of adipose-derived stem cells (ADSCs) and promoted osteochondral tissue regeneration.

Conclusion

These findings suggest potential applications of the n-HApMA/GelMA composite in the field of tissue engineering and regenerative medicine.

Recent Advances in the Development of Biomimetic Materials

In this review, we focused on recent efforts in the design and development of materials with biomimetic properties. Innovative methods promise to emulate cell microenvironments and tissue functions, but many aspects regarding cellular communication, motility, and responsiveness remain to be explained. We photographed the state-of-the-art advancements in biomimetics, and discussed the complexity of a "bottom-up" artificial construction of living systems, with particular highlights on hydrogels, collagen-based composites, surface modifications, and three-dimensional (3D) bioprinting applications. Fast-paced 3D printing and artificial intelligence, nevertheless, collide with reality: How difficult can it be to build reproducible biomimetic materials at a real scale in line with the complexity of living systems? Nowadays, science is in urgent need of bioengineering technologies for the practical use of bioinspired and biomimetics for medicine and clinics.

Stable Surface Modification by Cold Atmospheric-Pressure Plasma: Comparative Study on Cellulose-Based and Synthetic Polymers

This study's aim is a comparison of the plasma-induced effects on polymers exposed in helium and argon gaseous environments in a pulsed dielectric barrier discharge at atmospheric pressure. Cellulose-based and synthetic polymers are tested with regard to a range of parameters, such as wettability, adhesion, surface energy and polarity, the oxygen amount in their structure, and surface morphology. The surface properties are analyzed by contact angle measurements, X-ray photoelectron spectroscopy, and scanning electron microscopy images. The results point to the efficient and remarkably stable modifications of the plasma-exposed surfaces, such as their enhanced adhesion, surface energy, and oxygen incorporation. Additionally, plasma provides significant oxygen uptake in cellulose-based materials that bear already prior to treatment a high amount of oxygen in their structure. The comparison between the properties of the non-permeable, homogeneous, smooth-surface synthetic polymer and those of the loosely packed, porous, heterogeneous cellulose-based polymers points to the different rates of plasma-induced modification, whereby a progressive alteration of cellulosic surface properties over much larger ranges of exposure durations is noted. Present experimental conditions ensure mild treatments on such sensitive material, such as paper, and this is without alterations of the surface morphology and the physical degradation of the material over a large range of treatment duration.

Controlling Superhydrophobicity on Complex Substrates Based on a Vapor-Phase Sublimation and Deposition Polymerization

The superhydrophobic properties of material surfaces have attracted significant research and practical development in a wide range of applications. In the present study, a superhydrophobic coating was fabricated using a vapor-phase sublimation and deposition process. This process offers several advantages, including a controllable and tunable superhydrophobic property, a dry and solvent-free process that uses well-defined water/ice templates during fabrication, and a coating technology that is applicable to various substrates, regardless of their dimensions or complex geometric configurations. The fabrication process exploits time-dependent condensation to produce ice templates with a controlled surface morphology and roughness. The templates are sacrificed via vapor sublimation, which results in mass transfer of water vapor out of the system. A second vapor source of a polymer precursor is then introduced to the system, and deposition occurs upon polymerization on the iced templates, replicating the same topologies from the iced templates. The continuation of the co-current sublimation and deposition processes finally renders permanent hierarchical structures of the polymer coatings that combine the native hydrophobic property of the polymer and the structured property by the sacrificed ice templates, achieving a level of superhydrophobicity that is tunable from 90° to 164°. The experiments demonstrated the use of [2,2]paracyclophanes as the starting materials for forming the superhydrophobic coatings of poly(p-xylylenes) on substrate surfaces. In comparison to conventional vapor deposition of poly(p-xylylenes), which resulted in dense thin-film coatings with only a moderate water contact angle of approximately 90°, the reported superhydrophobic coatings and fabrication process can achieve a high water contact angle of 164°. Demonstrations furthermore revealed that the proposed coatings are durable while maintaining superhydrophobicity on various substrates, including an intraocular lens and a cardiovascular stent, even against harsh treatment conditions and varied solution compositions used on the substrates.

Leveraging the Dielectric Barrier Discharge Plasma Process to Create Regenerative Biocidal ePTFE Membranes

The utilization of dielectric barrier discharge (DBD) plasma treatment for modifying substrate surfaces constitutes an easy and simple approach with a potential for diverse applications. This technique was used to modify the surface of a commercial porous expanded poly(tetrafluoroethylene) (ePTFE) film with either dimethylaminoethyl methacrylate (DMAEMA) or (trimethylamino)ethyl methacrylate chloride (TMAEMA) monomers, aiming to obtain antibacterial ePTFE. Physicochemical analyses of the membranes revealed that DBD successfully enhanced the surface energy and surface charge of the membranes while maintaining high porosity (>75%) and large pore size (>1.0 μm). Evaluation of the bacteria killing-releasing (K-R) function revealed that both DMAEMA and TMAEMA endowed ePTFE with the ability to kill Escherichia coli bacteria. However, only TMAEMA-grafted ePTFE allowed for the release of dead bacteria from the surface upon washing with sodium hexametaphosphate (SHMP) saline solution, owing to its cationic charge derived from the quaternary amine. Washing with SHMP disturbed the electrostatic force between the polymer brushes and dead bacteria, which caused the release of the dead bacteria. Lastly, dead-end bacteria filtration showed that the TMAEMA-grafted ePTFE was able to kill 99.78% of the bacteria, while approximately 61.55% of bacteria were killed upon contact. The present findings support the feasibility of using DBD plasma treatment for designing surfaces that target bacteria and aid in the containment of disease-causing pathogens.

Use of Various UVC Photofunctionalization Times to Modify Surface Characteristics and Enhance the Biologic Activity of SLA Titanium

PURPOSE

To evaluate the effect of ultraviolet-C light (UVC) photofunctionalization treatment time on the biologic activity of airborne particle-abraded and acid-etched (SLA) titanium surfaces and to analyze its physical and chemical mechanisms.

MATERIALS AND METHODS

SLA titanium was treated with UVC light for different lengths of time (10 minutes, 20 minutes, 30 minutes, 1 hour, 2 hours, 4 hours, and 24 hours), and then changes to its surface characteristics were evaluated via electron microscope scanning, X-ray photoelectron spectroscopy (XPS), water contact angle measurement, and zeta potential measurement. The effect of UVC photofunctionalization on the biologic processes of SLA titanium surfaces was assessed by analyzing the bovine serum albumin adsorption, adhesion, proliferation, morphology, and alkaline phosphatase activity of MG-63 cells.

RESULTS

UVC irradiation did not change the topography of SLA titanium surfaces. As treatment times increased, the water contact angle decreased from 120 degrees to 0 degrees, and the hydrocarbon content decreased. Zeta potential testing showed increased surface potential of photofunctionalized titanium. In vitro testing showed that cell adhesion, proliferation, morphology, and alkaline phosphate (ALP) activity on titanium surfaces were significantly improved by UVC photofunctionalization.

CONCLUSIONS

UVC photofunctionalization can improve the biologic activity of SLA titanium surfaces by removing hydrocarbons and increasing the surface potential of titanium.

Leveraging Microgels Prepared from Poly(ethylene glycol) Bisepoxide and Polyetheramine for Versatile Surface Structuring of Agarose Hydrogels

We demonstrate a macromer-type bisepoxide, poly(ethylene glycol) diglycidyl ether, polymerizing readily with a trifunctional polyetheramine Jeffamine T-403 in water to facilitate the development of a series of microgels abbreviated as PMG. Simply by varying the concentration of the as-prepared thermoresponsive intermediate prepolymer from 1 to 2 and 4%, hydrodynamic sizes of the resulting P1MG, P2MG, and P4MG are easily tuned in the submicrometer to micrometer range shown by the dynamic light scattering results. Besides size difference, these microgels also deform differently, where the drying-induced deformation effect is most severe for P1MG and least prominent for P4MG. Simple evaporative deposition of PMG into multilayer packing provides versatile and green options for microgel-mediated surface structuring of agarose hydrogels. Specifically, deformabile P1MG- and P2MG-derived coatings render agarose gel microwrinkle textures by buckling against swelling-induced surface instability. Conversely, stiffer P4MG microgels lead to a patchy patterned hierarchical coating on agarose, similar to the cracking effect in drying colloidal films. The straightforward microgel-on-macrogel strategy allows integration of both wrinkle and patchy patterns to generate Janus-type agarose gels, just by rationally arranging the coating sequence. Diversifying topographic features attainable through microgel-based coatings on hydrogels could potentially make the sustainable and biocompatible material of agarose a more compelling choice for bioapplications. Brief demonstrations of the broad applicability of P1MG toward wrinkling of proteinaceous and synthetic hydrogels further highlight promising prospects of the PMG microgel-on-macrogel functionalization strategy.

[Progress in antibacterial/osteogenesis dual-functional surface modification strategy of titanium-based implants]

Objective

To review antibacterial/osteogenesis dual-functional surface modification strategy of titanium-based implants, so as to provide reference for subsequent research.

Methods

The related research literature on antibacterial/osteogenesis dual-functional surface modification strategy of titanium-based implants in recent years was reviewed, and the research progress was summarized based on different kinds of antibacterial substances and osteogenic active substances.

Results

At present, the antibacterial/osteogenesis dual-functional surface modification strategy of titanium-based implants includes: ① Combined coating strategy of antibiotics and osteogenic active substances. It is characterized in that antibiotics can be directly released around titanium-based implants, which can improve the bioavailability of drugs and reduce systemic toxicity. ② Combined coating strategy of antimicrobial peptides and osteogenic active substances. The antibacterial peptides have a wide antibacterial spectrum, and bacteria are not easy to produce drug resistance to them. ③ Combined coating strategy of inorganic antibacterial agent and osteogenic active substances. Metal ions or metal nanoparticles antibacterial agents have broad-spectrum antibacterial properties and various antibacterial mechanisms, but their high-dose application usually has cytotoxicity, so they are often combined with substances that osteogenic activity to reduce or eliminate cytotoxicity. In addition, inorganic coatings such as silicon nitride, calcium silicate, and graphene also have good antibacterial and osteogenic properties. ④ Combined coating strategy of metal organic frameworks/osteogenic active substances. The high specific surface area and porosity of metal organic frameworks can effectively package and transport antibacterial substances and bioactive molecules. ⑤ Combined coating strategy of organic substances/osteogenic active substancecs. Quaternary ammonium compounds, polyethylene glycol, N-haloamine, and other organic compounds have good antibacterial properties, and are often combined with hydroxyapatite and other substances that osteogenic activity.

Conclusion

The factors that affect the antibacterial and osteogenesis properties of titanium-based implants mainly include the structure and types of antibacterial substances, the structure and types of osteogenesis substances, and the coating process. At present, there is a lack of clinical verification of various strategies for antibacterial/osteogenesis dual-functional surface modification of titanium-based implants. The optimal combination, ratio, dose-effect mechanism, and corresponding coating preparation process of antibacterial substances and bone-active substances are needed to be constantly studied and improved.

Regulation Mechanism of Special Functional Groups Contained in Polymer Molecular Chains on the Tribological Properties of Modified Ti6Al4V

Polymer coatings can effectively improve the surface tribological properties of human implant materials, thereby increasing their service life. In this study, poly(vinylsulfonic acid, sodium salt) (PVS), poly(acrylic acid) (PAA) and poly(vinylphosphonic acid) (PVPA) were used to modify Ti6Al4V surfaces. Experimental analyses were combined with molecular simulation to explore the regulation mechanism of special functional groups contained in polymer molecular chains on the tribological properties of modified surfaces. In addition, the bearing capacities and velocity dependence of different polymer modified surfaces during friction were also explored. The PVS coating, due to physical adsorption, can have an anti-friction effect under NaCl solution lubrication, but is not durable under long-term or repeated usage. Both PAA and PVPA molecular chains can form chemical bonds with Ti6Al4V. Phosphate acid groups can firmly bind to the substrate, and the adsorption of salt ions and water molecules can form a hydrated layer on the PVPA coating surface, achieving ultra-low friction and wear. The adsorption of salt ions would aggravate the surface wear of the PAA-modified Ti6Al4V due to the unfirm binding of carboxyl groups to the substrate, resulting in a high friction coefficient. This study can provide effective guidance for the design of modified polymer coatings on metals.

Facile Modification of Medical-Grade Silicone for Antimicrobial Effectiveness and Biocompatibility: A Potential Therapeutic Strategy against Bacterial Biofilms

A one-step modification of biomedical silicone tubing with N,N-dimethyltetradecylamine, C14, results in a composition designated WinGard-1 (WG-1, 1.1 wt % C14). A surface-active silicon-amine phase (SAP) is proposed to account for increased wettability and increased surface charge. To understand the mechanism of antimicrobial effectiveness, several procedures were employed to detect whether C14 leaching occurred. An immersion-growth (IG) test was developed that required knowing the bacterial Minimum Inhibitory Concentrations (MICs) and Minimum Biocidal Concentrations (MBCs). The C14 MIC and MBC for Gm- uropathogenic E. coli (UPEC), commonly associated with catheter-associated urinary tract infections (CAUTI), were 10 and 20 μg/mL, respectively. After prior immersion of WG-1 silicone segments in a growth medium from 1 to 28 d, the IG test for the medium showed normal growth for UPEC over 24 h, indicating that the concentration of C14 must be less than the MIC, 10 μg/mL. GC-MS and studies of the medium inside and outside a dialysis bag containing WG-1 silicone segments supported de minimis leaching. Consequently, a 5 log UPEC reduction (99.999% kill) in 24 h using the shake flask test (ASTM E2149) cannot be due to leaching and is ascribed to contact kill. Interestingly, although the MBC was greater than 100 μg/mL for Pseudomonas aeruginosa, WG-1 silicone affected an 80% reduction via a 24 h shake flask test. For other bacteria and Candida albicans, greater than 99.9% shake flask kill may be understood by proposing increased wettability and concentration of charge illustrated in the TOC. De minimis leaching places WG-1 silicone at an advantage over conventional anti-infectives that rely on leaching of an antibiotic or heavy metals such as silver. The facile process for preparation of WG-1 silicone combined with biocidal effectiveness comprises progress toward the goals of device designation from the FDA for WG-1 and clearance.

Ultra-Short Laser-Assisted Micro-Structure Formations on Mg/Zn Double-Doped Calcium Phosphate Ceramics for Enhanced Antimicrobial Activity

Bacterial infection is one of the most common and harmful medical issues following the implantation of materials and devices in the body leading to antibiotic resistance of diverse bacterial strains. In this work, a novel approach is presented combining adopted laser-based patterning method in addition to doping (Mg and Zn) metal ions to prepare calcium phosphate ceramic substrate, applicable in medicine, with enhanced surface antimicrobial characteristics. The preparation of tablets containing Mg (8.44 mol%) and Zn (2.63 mol%) β-tricalcium phosphate involved biomimetic precipitation of amorphous calcium phosphate in media of simulated body fluid enriched with Mg2+ and Zn2+ ions as well as the presence of valine as an organic additive, followed by step-wise calcination up to 1000 °C. The results from laser processing showed formation of deeper patterns with increased surface roughness (from 4.9 µm to 9.4 µm) as laser power and velocity increase, keeping constant the hatch sizes of 50 µm. The textured surfaces consist of peaks and valleys arrangement that change the morphology of Escherichia coli cells and decrease of cell viability. Our study reveals the possibilities of the application of ultra-short laser radiation as a potential alternative therapy for controlling the antimicrobial effect of the ceramic surface.

Corrigendum: Challenge of material haemocompatibility for microfluidic blood-contacting applications

[This corrects the article DOI: 10.3389/fbioe.2023.1249753.].