Micro total analysis systems. Recent developments

Recent developments in optical detection methods for microchip separations

This paper summarizes the features and performances of optical detection systems currently applied in order to monitor separations on microchip devices. Fluorescence detection, which delivers very high sensitivity and selectivity, is still the most widely applied method of detection. Instruments utilizing laser-induced fluorescence (LIF) and lamp-based fluorescence along with recent applications of light-emitting diodes (LED) as excitation sources are also covered in this paper. Since chemiluminescence detection can be achieved using extremely simple devices which no longer require light sources and optical components for focusing and collimation, interesting approaches based on this technique are presented, too. Although UV/vis absorbance is a detection method that is commonly used in standard desktop electrophoresis and liquid chromatography instruments, it has not yet reached the same level of popularity for microchip applications. Current applications of UV/vis absorbance detection to microchip separations and innovative approaches that increase sensitivity are described. This article, which contains 85 references, focuses on developments and applications published within the last three years, points out exciting new approaches, and provides future perspectives on this field.

Ultralow hysteresis superhydrophobic surfaces by excimer laser modification of SU-8

We present a new and simple method to produce superhydrophobic surfaces with ultralow hysteresis. The method involves surface modification of SU-8 using an excimer laser treatment. The modified surface is coated with a hydrophobic plasma-polymerized hexafluoropropene layer. The advancing and receding water contact angles were measured to be approximately 165 degrees . The achieved water contact angle hysteresis was below the measurement limit. This low hysteresis can be ascribed to nanoscale debris generated during the excimer laser process.

Single p-type/intrinsic/n-type silicon nanowires as nanoscale avalanche photodetectors

We report the controlled synthesis of axial modulation-doped p-type/intrinsic/n-type (p-i-n) silicon nanowires with uniform diameters and single-crystal structures. The p-i-n nanowires were grown in three sequential steps: in the presence of diborane for the p-type region, in the absence of chemical dopant sources for the middle segment, and in the presence of phosphine for the n-type region. The p-i-n nanowires were structurally characterized by transmission electron microscopy, and the spatially resolved electrical properties of individual nanowires were determined by electrostatic force and scanning gate microscopies. Temperature-dependent current-voltage measurements recorded from individual p-i-n devices show an increase in the breakdown voltage with temperature, characteristic of band-to-band impact ionization, or avalanche breakdown. Spatially resolved photocurrent measurements show that the largest photocurrent is generated at the intrinsic region located between the electrode contacts, with multiplication factors in excess of ca. 30, and demonstrate that single p-i-n nanowires function as avalanche photodiodes. Electron- and hole-initiated avalanche gain measurements performed by localized photoexcitation of the p-type and n-type regions yield multiplication factors of ca. 100 and 20, respectively. These results demonstrate the significant potential of single p-i-n nanowires as nanoscale avalanche photodetectors and open possible opportunities for studying impact ionization of electrons and holes within quasi-one-dimensional semiconductor systems.

Integrated isotachophoretic preconcentration with zone electrophoresis separation on a quartz microchip for UV detection of flavonoids

A quartz microchip integrated isotachophoretic (ITP) preconcentration with zone electrophoresis (ZE) separation was fabricated using a novel multi-point pressure method featured in normal temperature and lower pressure during bonding process. ITP followed by subsequential ZE of two flavonoids, quercetin and isorhamnetin on the microchip was performed consecutively on the homemade microfluidic workstation with UV detection, resulting in a decreased detectable concentration of 32-fold, compared to the ZE mode only, and their detection limits decreased down to 0.2 microg/mL and 1.2 microg/mL, respectively.

Measurements of Surface Tension of Organic Solvents Using a Simple Microfabricated Chip

Measurement of the surface tension of organic solvents using a simple microfabricated chip was developed based on the principle of differential capillary rise. The theory, design, fabrication, and characterization of the chip were described. A two-step etching technique was used to fabricate a number of microchannels with different dimensions on the glass substrate. Capillarity was used to introduce liquid samples, which requires no power supply or actuator to be applied in the experiment. Liquid in different microchannels generated capillary rise with different heights, by which surface tension maybe calculated. Seven common organic solvents, ethanol, acetone, acetonitrile, dichloromethane, hexane, methanol, and toluene, were tested at room temperature. The surface tension of ethanol at different temperatures was measured over the range of 5-45 degrees C. Relative standard deviation for seven replicate measurements at each temperature is 0.20-0.74%. The results showed good reproducibility and acceptable precision compared with traditional methods. Very low reagent consumptions and short analysis time were achieved using this simple method.

Recent advances of microfluidics in Mainland China

The history and current status of research on microfluidics in China is summarized in this review. The recent representative contributions in this field by Chinese scientists are cited. A perspective on some trends in future development of this field in China is presented.

Field amplified sample stacking coupled with chip-based capillary electrophoresis using negative pressure sample injection technique

A multi-T microchip for integrated field amplified sample stacking (FASS) with CE separation to increase the chip-based capillary electrophoresis (chip-based CE) sensitivity was developed. Volumetrically defined large sample plug was formed in one step within 5s by the negative pressure in headspace of the two sealed sample waste reservoirs produced using a syringe pump equipped with a 3-way valve. Stacking and separation can proceed only by switching the 3-way valve to release the vacuum in headspace of the two sample waste reservoirs. This approach considerably simplified the operations and the equipments for FASS in chip-based CE systems. Migration time precisions of 3.3% and 1.3% RSD for rhodamine123 (Rh123) and fluorescien sodium salt (Flu) in the separation of a mixture of Flu and Rh123 were obtained for nine consecutive determinations with peak height precisions of 4.8% and 3.4% RSD, respectively. Compared with the chip-based CE on the cross microchip, the sensitivity for analysis of FlTC, FITC-labeled valine (Val) and Alanine (Ala) increased 55-, 41- and 43-fold, respectively.

Microfluidic technologies as platforms for performing quantitative cellular analyses in an in vitro environment

Quite often, important cellular events occur in environments that are either not amenable to implanted sensors or other types of molecular probes. In such cases, a viable alternative to taking the sensor or probe to the biological sample of interest is to bring the sample of interest out of its natural environment to one that is more conducive to the measurement scheme. The disadvantage of the latter approach is that the sample may not behave in the same manner in vitro as it does in vivo, or that the agonists and other stimuli to which the sample is subjected to in vivo are no longer present. In this Tutorial Review, the authors attempt to provide some guidance, based on their own experiences and those of other scientists, to performing cellular measurements in a quantitative manner under in vitro conditions. Due to the expansive literature on analyses involving cells, the authors have limited this Tutorial Review to those methods involving microfluidic technologies, both in microbore tubing and in microfabricated channels. Initial reports of analyses involving cells in microbore tubing were first reported nearly two decades ago, while those in microfabricated fluidic devices appeared over a decade ago. However, more recently, the complexity of cell analyses using fabricated microfluidic devices (as opposed to microbore tubing) has increased due in part to the improvements in fabrication technologies, fluid handling and delivery capabilities, advances in coatings of the channels within the microfluidic device, and integrated detection schemes. Examples of cellular analyses in microbore tubing and in fabricated microfluidic devices will be given, as well as associated advantages and challenges. Finally, the authors' thoughts on cellular analyses are presented here using the classical steps in an analysis as a guide.

New Approaches to Lipid Bilayer Fabrication: Microfluidic Solvent Extraction and Hydrogel Encapsulation

Membrane channel proteins play crucial roles in governing the transport of material and energy across every cellular membrane. Accordingly, they are the subjects of interest for science and medicine as well as major targets of drug discovery efforts. Recent work has also shown their potential as highly rapid and sensitive single molecule sensors. However, techniques conventionally used to measure the electrical transport through these proteins can be problematic to form and are extremely fragile, limiting the range and scope of possible studies. We have developed two new technologies which alleviate these shortcomings: in situ encapsulation of lipid membranes in hydrogels and automated microfluidic formation. The hydrogel encapsulated membranes are mechanically robust and long-lived as a result of the intimate contact between the hydrogel and the membrane, enabling measurements of single channel currents for a week or longer. The automated microfluidic formation apparatus enables the creation and manipulation of lipid membranes and the incorporation and measurement of channel proteins in these membranes through an entirely computer controlled process. We are working to apply these technologies toward DNA sequencing, drug discovery, and single molecule biophysics.

Capillary-assembled microchip as an on-line deproteinization device for capillary electrophoresis

A capillary-assembled microchip (CAs-CHIP), prepared by simply embedding square capillaries in a lattice polydimethylsiloxane (PDMS) channel plate with the same channel dimensions as the outer dimensions of the square capillaries, has been used as a diffusion-based pretreatment attachment in capillary electrophoresis (CE). Because the CAs-CHIPs employ square-section channels, diffusion-based separation of small molecules from sample solutions containing proteins is possible by using the multilayer flow formed in the square section channel. When a solution containing high-molecular-weight and low-molecular-weight species makes contact with a buffer solution, the low-molecular-weight species, which have larger diffusion coefficients than the high-molecular-weight species, can be collected in a buffer-solution phase. The collected solution containing the low-molecular-weight species is introduced into the separation capillary to be analyzed by CE. This type of system can be used for CE analysis in which pretreatment is required to remove proteins. In this work a fluorescently labeled protein and rhodamine-based molecules were chosen as model species and a feasibility study was performed.

Monolithic media in microfluidic devices for proteomics

Considerable effort has been invested in the development of integrated microfluidic devices for fast and highly efficient proteomic studies. Among various fabrication techniques for the preparation of analytical components (separation columns, reactors, extractors, valves, etc.) in integrated microchips, in situ fabrication of monolithic media is receiving increasing attention. This is mainly due to the ease and simplicity of preparation of monolithic media and the availability of various precursors and chemistries. In addition, UV-initiated photopolymerization technique enables the incorporation of multiple analytical components into specified parts of a single microchip using photomasks. This review summarizes preparation methods for monolithic media and their application as microfluidic analytical components in microchips.

Permanent surface modification of polymeric capillary electrophoresis microchips for protein and peptide analysis

Because of their surface heterogeneity, proteins readily adsorb on polymeric substrates via various interactions, which adversely affects the performance of polymeric microfluidic devices in electrophoresis-based protein/peptide analysis. Therefore, it is necessary to use surface modification techniques such as dynamic coating or more complicated permanent surface modification, which has broader application and better performance, to render the polymeric microchannels protein-resistant. This manuscript is a review of the surface chemistry of microfluidic devices used for electrophoretic separations of proteins and peptides. The structural complexity of proteins as it relates to adsorption is described, followed by a review of the mechanisms and structural characteristics of protein-resistant surfaces. Permanent surface modification techniques used in grafting protein-resistant materials onto the surfaces of electrophoresis microchannels fabricated from polymer substrates are summarized and successful examples are presented.

Continuous separation of particles using a microfluidic device equipped with flow rate control valves

We propose herein an improved microfluidic system for continuous and precise particle separation. We have previously proposed a method for particle separation called "pinched flow fractionation." Using the previously reported method, particles can be continuously separated according to differences in their diameters, simply by introducing liquid flows with and without particles into a specific microchannel structure. In this study, we incorporated PDMS membrane microvalves for flow rate control into the microfluidic device to improve the separation accuracy. By adjusting the flow rates distributed to each outlet, target particles could be precisely collected from the desired outlet. We succeeded in separating micron and submicron-size polymer particles. This method can be used widely for continuous and precise separation of various kinds of particles, and can function as an important part of microfluidic systems.

Direct Analysis of Trace Phenolics with a Microchip: In-Channel Sample Preconcentration, Separation, and Electrochemical Detection

A micrototal analytical method assembling in-channel preconcentration, separation, and electrochemical detection steps has been developed for trace phenolic compounds. A micellar electrokinetic chromatography separation technique was coupled with two preconcentration steps of field-amplified sample stacking (FASS) and field-amplified sample injection (FASI). An amperometric detection method with a cellulose-dsDNA-modified, screen-printed carbon electrode was applied to detect preconcentrated and separated species at the end of the channel. The microchip was composed of three parallel channels: first, two are for the sample preconcentration using FASS and FASI methods, and the third one is for the separation and electrochemical detection. The modification of the electrode surface improved the detection performance by enhancing the signal-to-noise characteristic without surface fouling of the electrode. The method was examined for the analysis of eight phenolic compounds. Experimental parameters affecting the analytical performance of the method were assessed and optimized. The preconcentration factor was increased by about 5200-fold as compared with a simple capillary zone electrophoretic analysis using the same channel. Reproducible response was observed during multiple injections of samples with a RSD of <8.0%. The calibration plots were shown to be linear (with the correlation coefficient between 0.9913 and 0.9982) over the range of 0.4-600 nM. The sensitivity was between 0.17 +/- 0.001 and 0.48 +/- 0.006 nA/nM, with the detection limit of approximately 100 to approximately 150 pM based on S/N = 3. The applicability of the method to the direct analysis of trace phenolic compounds in water samples was successfully demonstrated.

Automated formation of lipid-bilayer membranes in a microfluidic device

Although membrane channel proteins are important to drug discovery and hold great promise as engineered nanopore sensing elements, their widespread application to these areas has been limited by difficulties in fabricating planar lipid-bilayer membranes. We present a method for forming these sub-5-nm-thick free-standing structures based on a self-assembly process driven by solvent extraction in a microfluidic channel. This facile automatable process forms high-quality membranes able to host channel proteins measurable at single-molecule conductance resolution.

Cells on chips

Microsystems create new opportunities for the spatial and temporal control of cell growth and stimuli by combining surfaces that mimic complex biochemistries and geometries of the extracellular matrix with microfluidic channels that regulate transport of fluids and soluble factors. Further integration with bioanalytic microsystems results in multifunctional platforms for basic biological insights into cells and tissues, as well as for cell-based sensors with biochemical, biomedical and environmental functions. Highly integrated microdevices show great promise for basic biomedical and pharmaceutical research, and robust and portable point-of-care devices could be used in clinical settings, in both the developed and the developing world.

Circumventing air bubbles in microfluidic systems and quantitative continuous-flow PCR applications

Polymerase chain reaction (PCR) is an essential part of research based on genomics or cell analysis. The development of a microfluidic device that would be suitable for high-temperature-based reactions therefore becomes an important contribution towards the integration of micro-total analysis systems (muTAS). However, problems associated with the generation of air bubbles in the microchannels before the introduction of the assay liquid, which we call the "initial start-up" in this study, made the flow irregular and unstable. In this report, we have tried to address these problems by adapting a novel liquid-flow method for high-temperature-based reactions. A PDMS-based microfluidic device was fabricated by soft-lithography techniques and placed on a cartridge heater. The generation of the air bubbles was prevented by introducing the fluorinated oil, an inert and highly viscous liquid, as the cap just before the introduction of the sample solutions into the microchannels. The technique was applied for continuous-flow PCR, which could perform PCR on-chip in a microfluidic system. For the evaluation of practical accuracy, plasmid DNA that serves as a reference molecule for the quantification of genetically modified (GM) maize was used as the template DNA for continuous-flow PCR. After PCR, the products were collected in a vial and analyzed by gel electrophoresis to confirm the accuracy of the results. Additionally, quantitative continuous-flow PCR was performed using TaqMan technology on our PCR device. A laser detection system was also used for the quantitative PCR method. We observed a linear relationship between the threshold cycle (Ct) and the initial DNA concentration. These results showed that it would be possible to quantify the initial copies of the template DNA on our microfluidic device. Accurate quantitative DNA analysis in microfluidic systems is required for the integration of PCR with muTAS, thus we anticipate that our device would have promising potential for applications in a wide range of research.

Fully integrated whole blood testing by real-time absorption measurement on a centrifugal platform

We present a novel microfluidic concept to enable a fast colorimetric alcohol assay from a single droplet of whole blood. The reduced turn-around time of 150 seconds is, on the one hand, achieved by a full process integration including metering, mixing with reagents, and sedimentation of cellular constituents. On the other hand, our novel total internal reflection (TIR) scheme allows to monitor the increase of the absorbance values in real-time. Thus, the saturation values can be predicted accurately based on an extrapolation of real-time measurements acquired during a 100 second initial period of rotation. Additionally, we present a metering structure to define nanolitre sample volumes at a coefficient of variation (CV) below 5%.

Monolithically integrated dye-doped PDMS long-pass filters for disposable on-chip fluorescence detection

We report the fabrication of high quality monolithically integrated optical long-pass filters, for use in disposable diagnostic microchips. The filters were prepared by incorporating dye molecules directly into the microfluidic chip substrate, thereby providing a fully integrated solution that removes the usual need for discrete optical filters. In brief, lysochrome dyes were added to a poly(dimethylsiloxane) (PDMS) monomer prior to moulding of the microchip from a structured SU-8 master. Optimum results were obtained using 1 mm layers of PDMS doped with 1200 microg mL(-1) Sudan II, which resulted in less than 0.01% transmittance below 500 nm (OD 4), >80% above 570 nm, and negligible autofluorescence. These spectral characteristics compare favourably with commercially available Schott-glass long-pass filters, indicating that high quality optical filters can be straightforwardly integrated into the form of PDMS microfluidic chips. The filters were found to be robust in use, showing only slight degradation after extended illumination and negligible dye leaching after prolonged exposure to aqueous solutions. The provision of low cost high quality integrated filters represents a key step towards the development of high-sensitivity disposable microfluidic devices for point-of-care diagnostics.

Control of electroosmotic flow by polymer coating: effects of the electrical double layer

We report on the molecular dynamics simulations of electroosmotic flow control by polymer coating. We show that polymer coating modulates the flow by rendering drag to fluids and by changing the ion distribution and ion-surface interactions in the electrical double layer. Because of the latter two effects, the polymer coating can even enhance the flow under certain conditions. Identifying the effects of these processes is crucial for the rational design of polymer coating for electroosmotic flow control.

Initial study of two-phase laminar flow extraction chip for sample preparation for gas chromatography

A sample preparation method for gas chromatography using a two-phase, laminar flow extraction PDMS/glass chip has been developed. A stable two-phase laminar interface was obtained by surface modification, and the organic extraction phase and the aqueous sample phase were separated effectively when the two-phase laminar flows exit the chip. Experiments were conducted on the chip to extract ephedrine from aqueous solution. Good reproducibility was obtained over the entire range of ephedrine concentration using the extraction chips (CV range 2.7%-4.5%). Effects of salt and solvent on extraction efficiency were studied.

Solution-Phase Surface Modification in Intact Poly(dimethylsiloxane) Microfluidic Channels

An improved approach composed of an oxidation reaction in acidic H2O2 solution and a sequential silanization reaction using neat silane reagents for surface modification of poly(dimethylsiloxane) (PDMS) substrates was developed. This solution-phase approach is simple and convenient for some routine analytical applications in chemistry and biology laboratories and is designed for intact PDMS-based microfluidic devices, with no device postassembly required. Using this improved approach, two different functional groups, poly(ethylene glycol) (PEG) and amine (NH2), were introduced onto PDMS surfaces for passivation of nonspecific protein absorption and attachment of biomolecules, respectively. X-ray electron spectroscopy and temporal contact angle experiments were employed to monitor functional group transformation and dynamic characteristics of the PEG-grafted PDMS substrates; fluorescent protein solutions were introduced into the PEG-grafted PDMS microchannels to test their protein repelling characteristics. These analytical data indicate that the PEG-grafted PDMS surfaces exhibit improved short-term surface dynamics and robust long-term stability. The amino-grafted PDMS microchannels are also relatively stable and can be further activated for modifications with peptide, DNA, and protein on the surfaces of microfluidic channels. The resulting biomolecule-grafted PDMS microchannels can be utilized for cell immobilization and incubation, semiquantitative DNA hybridization, and immunoassay.

High-efficiency electrokinetic micromixing through symmetric sequential injection and expansion

Rapid electric field switching is an established microfluidic mixing strategy for electrokinetic flows. Many such microfluidic mixers are variations on the T- or Y-form channel geometry. In these configurations, rapid switching of the electric field can greatly improve initial mixing over that achieved with static-field mixing. Due to a fundamental lack of symmetry, however, these strategies produce lingering cross-channel concentration gradients which delay complete mixing of the fluid stream. In this paper, a field switching microfluidic mixing strategy which utilizes a symmetric sequential injection geometry with an expansion chamber to achieve high efficiency microfluidic mixing is demonstrated experimentally. A three-inlet injector sequentially interlaces two dissimilar incoming solutions. Downstream of the injector, the sequence enters an expansion chamber resulting in a dramatic (two orders of magnitude) decrease in Peclet number and rapid axial diffusive mixing. The outlet concentration may be accurately varied over the full spectrum by tuning the duty cycle of the field switching waveform. The chips are designed with input from a previous numerical study, manufactured in poly(dimethylsiloxane) using soft-lithography based microfabrication, and tested using fluorescence microscopy. In the context of on-chip chemical processing for analytical operations, the demonstrated mixing strategy has several features: high mixing efficiency (99%), compact axial length (2.3 mm), steady outflow velocity, and readily variable outlet concentration (0.15 < c* < 0.95).

Monitoring and Kinetics Study of a Single Particle on a Simple Microfluidic Chip

A single-channel poly(dimethylsiloxane) microchip was developed for the desorption process monitoring and kinetics studies of a single particle. The microchannel consisting of a narrow section following a relatively wide part enabled particle introduction, transfer, and location. A microinfusion pump was employed to delivery eluting solution at a precise rate. Once the particle contacted with the eluting solution, the solute transferred from particle into eluting solution and would be detected by laser-induced fluorescence or a chemiluminescence detector. Desorption process of a single particle was sensitively monitored. Depending on the desorption curves obtained, kinetics studies were carried out. The sediment desorption process analyses of single resin particles and single active carbon particles were performed.

Microscale features and surface chemical functionality patterned by electron beam lithography: a novel route to poly(dimethylsiloxane) (PDMS) stamp fabrication

Poly(dimethylsiloxane) (PDMS) has become a ubiquitous material for microcontact printing, yet there are few methods available to pattern a completed PDMS stamp in a single step. It is shown here that electron beam lithography (EBL) is effective in writing patterns directly onto cured PDMS stamps, thus overcoming the need for multiple patterning steps. Not only does this method allow the modification of an existing lithographic pattern, but new 3D features such as cones, pits, and channels can also be fabricated. EBL can also be used to fabricate PDMS masks for photolithography whereby 1:1 pattern transfer into a photoresist is achieved. Additionally, direct EBL writing of surface chemical features has been achieved using a PDMS stamp coated with a self-assembled monolayer. An electrostatic mechanism appears to be operative in the EBL patterning process, as supported by calculations, thermogravimetric analysis, time-of-flight secondary ion mass spectroscopy, optical and atomic force microscopy, and chemical functionalization assays.

Multicolor Fluorescence Detection on an Electrophoretic Microdevice Using an Acoustooptic Tunable Filter

An acoustooptic tunable filter (AOTF) is used to detect multiple fluorescent signals on a fluidic microdevice. A confocal laser-induced fluorescence detection setup is used to excite fluorescent dyes in glass microchannels, presenting a streamlined and robust detection system consisting of the narrow-bandwidth AO filter and a single photodetector. The flexibility of the filter is demonstrated by alternating between wavelengths for precise microchannel alignment and sweeping through a range of wavelengths for preliminary spectral characterization of subnanoliter probe volumes of target analytes. The AOTF is also coupled with an electrophoretic separation for the multicolor detection of PCR-amplified DNA against a labeled sizing standard, the discrimination of multiple amplicons overlapped in time, and the identification of amplified biowarfare agents in a fluorescent spiking experiment. Finally, to demonstrate the multicolor capability of the system, 19-wavelength detection is performed during the separation of a three-dye sample mixture.

Bioanalysis in structured microfluidic systems

Microfluidic and lab-on-a-chip devices have attracted widespread interest in separation sciences and bioanalysis. Recent designs in microfluidic devices extend common separation concepts by exploiting new phenomena for molecular dynamics on a length scale of 10 mum and below, giving rise to novel manipulation tools and nonintuitive phenomena for microseparations. Here, we focus on three very recent developments for bioseparations based on tailored microfluidic systems: Single cell navigation, trapping and steering with subsequent on-chip lysis, protein separation and LIF detection (Section 3.1), then we report dielectrophoretic trapping and separation of large DNA fragments in structured microfluidic devices (Section 3.2). Finally, a paradoxial migration phenomenon based on thermal fluctuations, periodically arranged microchannels and a biased alternating current electric field is presented in Section 3.3.

Grafting epoxy-modified hydrophilic polymers onto poly(dimethylsiloxane) microfluidic chip to resist nonspecific protein adsorption

In order to achieve a simple covalent hydrophilic polymer coating on poly(dimethylsiloxane) (PDMS) microfluidic chip, epoxy modified hydrophilic polymers were synthesized in aqueous solution with a persulfate radical initiation system, and crosslinked onto PDMS pretreated by oxygen plasma and silanized with 3-aminopropyl-triethoxysilanes (APTES). Glycidyl methacrylate (GMA) was copolymerized with acrylamide (poly(AAM-co-GMA)) or dimethylacrylamide (poly(DAM-co-GMA)), and graft polymerized with polyvinylpyrrolidone (PVP-g-GMA) or polyvinylalcohol (PVA-g-GMA). The epoxy groups in the polymers were determined by UV spectra after derivation with benzylamine. Reflection absorption infrared spectroscopy (RAIRS) confirmed covalent grafting of GMA-modified polymers onto PDMS surface. Electroosmotic flow (EOF) in the polymer grafted microchannel was strongly suppressed within the range pH 3-11. Surface adsorption of lysozyme and bovine serum albumin (BSA) was reduced to less than 10% relative to that on the native PDMS surface. On the GMA-modified polymer coated PDMS microchip, basic proteins, peptides, and sodium dodecyl sulfate (SDS) denatured proteins were separated successfully.

Single potential electrophoresis microchip with reduced bias using pressure pulse injection

We propose two variants of a new injection technique for use in electrophoresis microchips, called "front gate pressure injection" and "back gate pressure injection", that both enable a controlled and reproducible sample introduction with reduced bias compared to electrokinetic gated injection. A continuous flow of a test solution of fluorescein/rhodamine B in 20 mM Tris/boric acid buffer (pH 8.6) sample test solution is electrokinetically driven near to the entrance of the separation channel, using a single voltage (3 kV) that is constant in time. A sample plug is injected in the separation channel by a pressure pulse of the order of 0.1 s. The latter is generated using the mechanical deflection of a PDMS membrane that is loosely placed on a dedicated chip reservoir. The analysis of the peak area ratio of the separated compounds demonstrates a nearly constant sample composition when using pressure-based injection. A small remaining injection bias for the shortest membrane deflection times can be attributed to a dilution effect of the charged compound due to the presence of an electrical field transverse to the sample flow boundary in the channel junction.

Improved native UV laser induced fluorescence detection for single cell analysis in poly(dimethylsiloxane) microfluidic devices

Single cell analytics is a key method in the framework of proteom research allowing analyses, which are not subjected to ensemble-averaging, cell-cycle or heterogeneous cell-population effects. Our previous studies on single cell analysis in poly(dimethylsiloxane) microfluidic devices with native label-free laser induced fluorescence detection [W. Hellmich, C. Pelargus, K. Leffhalm, A. Ros, D. Anselmetti, Electrophoresis 26 (2005) 3689] were extended in order to improve separation efficiency and detection sensitivity. Here, we particularly focus on the influence of poly(oxyethylene) based coatings on the separation performance. In addition, the influence on background fluorescence is studied by the variation of the incident laser power as well as the adaptation of the confocal volume to the microfluidic channel dimensions. Last but not least, the use of carbon black particles further enhanced the detection limit to 25 nM, thereby reaching the relevant concentration ranges necessary for the label-free detection of low abundant proteins in single cells. On the basis of these results, we demonstrate the first electropherogram from an individual Spodoptera frugiperda (Sf9) cell with native label-free UV-LIF detection in a microfluidic chip.

Electrostatic induction of the electric field into free-flow electrophoresis devices

The electrostatic induction of an applied voltage causes electrophoretic separation under free-flow conditions and no electrolysis or electric current flowing between the metal electrodes was observed.

Off-line form of the Michaelis-Menten equation for studying the reaction kinetics in a polymer microchip integrated with enzyme microreactor

We firstly transformed the traditional Michaelis-Menten equation into an off-line form which can be used for evaluating the Michaelis-Menten constant after the enzymatic reaction. For experimental estimation of the kinetics of enzymatic reactions, we have developed a facile and effective method by integrating an enzyme microreactor into direct-printing polymer microchips. Strong nonspecific adsorption of proteins was utilized to effectively immobilize enzymes onto the microchannel wall, forming the integrated on-column enzyme microreactor in a microchip. The properties of the integrated enzyme microreactor were evaluated by using the enzymatic reaction of glucose oxidase (GOx) with its substrate glucose as a model system. The reaction product, hydrogen peroxide, was electrochemically (EC) analyzed using a Pt microelectrode. The data for enzyme kinetics using our off-line form of the Michaelis-Menten equation was obtained (K(m) = 2.64 mM), which is much smaller than that reported in solution (K(m) = 6.0 mM). Due to the hydrophobic property and the native mesoscopic structure of the poly(ethylene terephthalate) film, the immobilized enzyme in the microreactor shows good stability and bioactivity under the flowing conditions.

Centrifugal extraction of plasma from whole blood on a rotating disk

We present a centrifugal process for the extraction of plasma from sediment by a decanting structure, terminating with metered plasma which is readily available for subsequent on-disk processing. Our technique supplies 2 microl plasma from 5 microl of whole blood at moderate spinning frequencies of 40 Hz within 20 s, only. The residual cell concentration in the purified plasma amounts to less than 0.11%, independent of the frequency of rotation. A capillary duct connects the extracted plasma to subsequent on-disk processing units.

Electronic drop sensing in microfluidic devices: automated operation of a nanoliter viscometer

We describe three droplet sensing techniques: a digital electrode, an analog electrode, and a thermal method. All three techniques use a single layer of metal lines that is easy to microfabricate and an electronic signal can be produced using low DC voltages. While the electrode methods utilize changes in electrical conductivity when the air/liquid interface of the droplet passes over a pair of electrodes, the thermal method is based on convective heat loss from a locally heated region. For the electrode method, the analog technique is able to detect 25 nL droplets while the digital technique is capable of detecting droplets as small as 100 pL. For thermal sensing, temperature profiles in the range of 36 degrees C and higher were used. Finally, we have used the digital electrode method and an array of electrodes located at preset distances to automate the operation of a previously described microfluidic viscometer. The viscometer is completely controlled by a laptop computer, and the total time for operation including setup, calibration, sample addition and viscosity calculation is approximately 4 minutes.

Design and fabrication of nanofluidic devices by surface micromachining

Using surface micromachining technology, we fabricated nanofluidic devices with channels down to 10 nm deep, 200 nm wide and up to 8 cm long. We demonstrated that different materials, such as silicon nitride, polysilicon and silicon dioxide, combined with variations of the fabrication procedure, could be used to make channels both on silicon and glass substrates. Critical channel design parameters were also examined. With the channels as the basis, we integrated equivalent elements which are found on micro total analysis (μTAS) chips for electrokinetic separations. On-chip platinum electrodes enabled electrokinetic liquid actuation. Micro-moulded polydimethylsiloxane (PDMS) structures bonded to the devices served as liquid reservoirs for buffers and sample. Ionic conductance measurements showed Ohmic behaviour at ion concentrations above 10 mM, and surface charge governed ion transport below 5 mM. Low device to device conductance variation (1%) indicated excellent channel uniformity on the wafer level. As proof of concept, we demonstrated electrokinetic injections using an injection cross with volume below 50 attolitres (10(-18) l).

Sensitivity enhancement for colorimetric glucose assays on whole blood by on-chip beam-guidance

In this paper, we present a novel concept for optical beam-guidance to significantly enhance the sensitivity of colorimetric assays by extending the optical path length through the detection cell which linearly impacts the resulting attenuation of a probe beam according to the law of Beer-Lambert. In our setup, the incident probe beam is deflected by 90( composite function) into the chip plane at monolithically integrated V-grooves to pass a flat detection cell at its full width (i.e., with a path length of 10 mm) instead of its usually much smaller height. Afterwards, the attenuated beam is redirected by another V-groove towards an external detector. The general beam-guidance concept is demonstrated by a glucose assay on human whole blood on a centrifugal microfluidic "lab-on-a-disk" platform made of COC. We achieve an excellent linearity with a correlation coefficient (R (2)) of 0.997 paired with a lower limit of detection (200 microM) and a good reproducibility with a coefficient of variation (CV) of 4.0% over nearly three orders of magnitude. With an accelerated sedimentation of cellular constituents by centrifugal forces, the sample of whole blood can be analyzed in a fully integrated fashion within 210 s. This time-to-result can even be improved by the numerical extrapolation of the saturation value. Additionally, the direct assay on whole blood also shows a negligible correlation with the hematocrit of the blood sample.

Integrated Preconcentration SDS−PAGE of Proteins in Microchips Using Photopatterned Cross-Linked Polyacrylamide Gels

The potential of integration of functions in microfluidic chips is demonstrated by implementing on-chip preconcentration of proteins prior to on-chip protein sizing by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). Two polymeric elements-a thin (approximately 50 microm) size exclusion membrane for preconcentration and a longer (approximately cm) porous monolith for protein sizing-were fabricated in situ using photopolymerization. Contiguous placement of the two polymeric elements in the channels of a microchip enabled simple and zero dead volume integration of the preconcentration with SDS-PAGE. The size exclusion membrane was polymerized in the injection channel using a shaped laser beam, and the sizing monolith was cast by photolithography using a mask and UV lamp. Proteins injected electrophoretically were trapped on the upstream side of the size exclusion membrane (MW cutoff approximately 10 kDa) and eluted off the membrane by reversing the electric field. Subsequently, the concentrated proteins were separated in a cross-linked polyacrylamide monolith that was patterned contiguous to the size exclusion membrane. The extent of protein preconcentration is easily tuned by varying the voltage during injection or by controlling the sample volume loaded. Electric fields applied across the nanoporous membrane resulted in a concentration polarization effect evidenced by decreasing current over time and irreproducible migration of proteins during sizing. To minimize the concentration polarization effect, sieving gels were polymerized only on the separation side of the membrane, and an alternate electrical current path was employed, bypassing the membrane, for most of the elution and separation steps. Electrophoretically sweeping a fixed sample volume against the membrane yields preconcentration factors that are independent of protein mobility. The volume sweeping method also avoids biased protein loading from concentration polarization and sample matrix variations. Mobilities of the concentrated proteins were log-linear with respect to molecular weight, demonstrating the suitability of this approach for protein sizing. Proteins were concentrated rapidly (<5 min) over 1000-fold followed by high-resolution separation in the sieving monolith. Proteins with concentrations as low as 50 fM were detectable with 30 min of preconcentration time. The integrated preconcentration-sizing approach facilitates analysis of low-abundant proteins that cannot be otherwise detected. Moreover, the integrated preconcentration-analysis approach employing in situ formation of photopatterned polymeric elements provides a generic, inexpensive, and versatile method to integrate functions at chip level and can be extended to lowering of detection limits for other applications such as DNA analysis and clinical diagnostics.

Fabrication of Conductive Membrane in a Polymeric Electric Field Gradient Focusing Microdevice

A novel approach to integrating a buffer ion-permeable membrane in a poly(glycidyl methacrylate-co-methyl methacrylate) micro electric field gradient focusing (muEFGF) device is described. A weir structure on which the membrane was positioned was fabricated between the separation channel and field gradient-generating channel. Before formation of the membrane, the surface of the polymeric microdevice was treated for covalent bonding of the membrane. Following surface modification, a prepolymer solution containing poly(ethylene glycol) acrylate/methacrylate and Tris-HCl buffer was loaded into the microdevice. Low-pressure nitrogen gas was then purged through the separation and field gradient-generating channels to remove the prepolymer solution from these channels. Residual prepolymer solution was retained on the weir structure due to surface tension. Finally, the premembrane was cured in place on the weir using UV radiation. Using a muEFGF device, green fluorescent protein (GFP) was concentrated 4000-fold. Separation of GFP and R-phycoerythrin, and selective elution of GFP from a protein mixture containing GFP, FITC-labeled casein, and FITC-labeled hemoglobin were also demonstrated. It was found that the membrane conductivity and presence of carboxylic acid impurities in the membrane strongly affected the behavior of the muEFGF device.

Integration of microcolumns and microfluidic fractionators on multitasking centrifugal microfluidic platforms for the analysis of biomolecules

This work demonstrates the development of microfluidic compact discs (CDs) for protein purification and fractionation integrating a series of microfluidic features, such as microreservoirs, microchannels, and microfluidic fractionators. The CDs were fabricated with polydimethylsiloxane (PDMS), and each device contained multiple identical microfluidic patterns. Each pattern employed a microfluidic fractionation feature with operation that was based on the redirection of fluid into an isolation chamber as a result of an overflow. This feature offers the advantage of automated operation without the need for any external manipulation, which is independent of the size and the charge of the fractionated molecules. The performance of the microfluidic fractionator was evaluated by its integration into a protein purification microfluidic architecture. The microfluidic architecture employed a microchamber that accommodated a monolithic microcolumn, the fractionator, and an isolation chamber, which was also utilized for the optical detection of the purified protein. The monolithic microcolumn was polymerized "in situ" on the CD from a monolith precursor solution by microwave-initiated polymerization. This technique enabled the fast, efficient, and simultaneous polymerization of monoliths on disposable CD microfluidic platforms. The design of the CD employed allows the integration of various processes on a single microfluidic device, including protein purification, fractionation, isolation, and detection.

DNA and microfluidics: Building molecular electronics systems

The development of molecular electronics using DNA molecules as the building blocks and using microfluidics to build nanowire arrays is reviewed. Applications of DNA conductivity to build sensors and nanowire arrays, and DNA conjugation with other nanostructures, offers an exciting opportunity to build extremely small analytical devices that are suitable for single-molecule detection and also target screening.

Unconventional detection methods for microfluidic devices

The direction of modern analytical techniques is to push for lower detection limits, improved selectivity and sensitivity, faster analysis time, higher throughput, and more inexpensive analysis systems with ever-decreasing sample volumes. These very ambitious goals are exacerbated by the need to reduce the overall size of the device and the instrumentation - the quest for functional micrototal analysis systems epitomizes this. Microfluidic devices fabricated in glass, and more recently, in a variety of polymers, brings us a step closer to being able to achieve these stringent goals and to realize the economical fabrication of sophisticated instrumentation. However, this places a significant burden on the detection systems associated with microchip-based analysis systems. There is a need for a universal detector that can efficiently detect sample analytes in real time and with minimal sample manipulation steps, such as lengthy labeling protocols. This review highlights the advances in uncommon or less frequently used detection methods associated with microfluidic devices. As a result, the three most common methods - LIF, electrochemical, and mass spectrometric techniques - are omitted in order to focus on the more esoteric detection methods reported in the literature over the last 2 years.