Collagen/cellulose hydrogel beads reconstituted from ionic liquid solution for Cu(II) adsorption

Natural Polysaccharide-Based Hydrogels Used for Dye Removal

Removal of contaminants from discharge water is vital and demands urgent assistance with the goal to keep clean water. Adsorption is one of the most common, efficient, and low-priced methods used in water treatment. Various polysaccharide-based gels have been used as efficient dye adsorbents from wastewater. This review summarizes cutting-edge research of the last decade of different hydrogels based on natural polysaccharides (chitin, chitosan, cellulose, starch, pullulan, and dextran) concerning their dye adsorption efficiency. Beyond their natural abundance, attributes of polysaccharides such as biocompatibility, biodegradability, and low cost make them not only efficient, but also environmentally sustainable candidates for water purification. The synthesis and dye removal performance together with the effect of diverse factors on gels retaining ability, kinetic, and isotherm models encountered in adsorption studies, are introduced. Thermodynamic parameters, sorbent recycling capacity along with conclusions and future prospects are also presented.

Development of Blended Biopolymer-Based Photocatalytic Hydrogel Beads for Adsorption and Photodegradation of Dyes

Blended biopolymer-based photocatalytic hydrogel beads were synthesized by dissolving the biopolymers in 1-ethyl-3-methylimidazolium acetate ([Emim][Ac]), adding TiO2, and reconstituting the beads with ethanol. The incorporation of modifying biopolymer significantly enhanced the adsorption capacity of the cellulose/TiO2 beads. Cellulose/carrageenan/TiO2 beads exhibited a 7.0-fold increase in adsorption capacity for methylene blue (MB). In contrast, cellulose/chitosan/TiO2 beads showed a 4.8-fold increase in adsorption capacity for methyl orange (MO) compared with cellulose/TiO2 beads. In addition, cellulose/TiO2 microbeads were prepared through the sol-gel transition of the [Emim][Ac]-in-oil emulsion to enhance photodegradation activity. These microbeads displayed a 4.6-fold higher adsorption capacity and 2.8-fold higher photodegradation activity for MB than the millimeter-sized beads. Furthermore, they exhibited superior dye removal efficiencies for various dyes such as Congo red, MO, MB, crystal violet, and rhodamine B, surpassing the performance of larger beads. To expand the industrial applicability of the microbeads, biopolymer/TiO2 magnetic microbeads were developed by incorporating Fe2O3. These magnetic microbeads outperformed millimeter-sized beads regarding the efficiency and time required for MB removal from aqueous solutions. Furthermore, the physicochemical properties of magnetic microbeads can be easily controlled by adjusting the type of biopolymer modifier, the TiO2 and magnetic particle content, and the ratio of each component based on the target molecule. Therefore, biopolymer-based photocatalytic magnetic microbeads have great potential not only in environmental fields but also in biomedical fields.

Fabrication of chitosan@activated carbon composites in EmimAc for Cd(II) adsorption from aqueous solution: Experimental, optimization and DFT study

Adsorption efficiency of a duo-material blend featuring the fabrication of modified chitosan adsorbents (powder (C-emimAc), bead (CB-emimAc) and sponge (CS-emimAc)) for the removal of Cd(II) from aqueous solution was investigated. The chitosan@activated carbon (Ch/AC) blend was developed in a green ionic solvent, 1-ethyl-3-methyl imidazolium acetate (EmimAc) and its characteristics was examined using FTIR, SEM, EDX, BET and TGA. The possible mechanism of interaction between the composites and Cd(II) was also predicted using the density functional theory (DFT) analysis. The interactions of various blend forms (C-emimAc, CB-emimAc and CS-emimAc) with Cd(II) gave better adsorption at pH 6. The composites also present excellent chemical stability in both acidic and basic conditions. The monolayer adsorption capacities obtained (under the condition 20 mg/L [Cd], adsorbent dosage 5 mg, contact time 1 h) for the CB-emimAc (84.75 mg/g) > C-emimAc (72.99 mg/g) > CS-emimAc (55.25 mg/g), as this was supported by their order of increasing BET surface area (CB-emimAc (120.1 m²/g) > C-emimAc (67.4 m²/g) > CS-emimAc (35.3 m²/g)). The feasible adsorption interactions between Cd(II) and Ch/AC occurs through the O-H and N-H groups of the composites, as supported by DFT analysis in which an electrostatic interactions was predicted as the dominant force. The interaction energy (-1309.35 eV) calculated via DFT shows that the Ch/AC with amino (-NH) and hydroxyl (-OH) groups are more effective with four significant electrostatic interactions with the Cd(II) ion. The various form of Ch/AC composites developed in EmimAc possess good adsorption capacity and stability for the adsorption Cd(II).

UV-Cured Chitosan-Based Hydrogels Strengthened by Tannic Acid for the Removal of Copper Ions from Water

In this work, a new environmentally friendly material for the removal of heavy metal ions was developed to enhance the adsorption efficiency of photocurable chitosan-based hydrogels (CHg). The acknowledged affinity of tannic acid (TA) to metal ions was investigated to improve the properties of hydrogels obtained from natural and renewable sources (CHg-TA). The hydrogel preparation was performed via a simple two-step method consisting of the photocrosslinking of methacrylated chitosan and its subsequent swelling in the TA solution. The samples were characterized using ATR-FTIR, SEM, and Folin-Ciocalteu (F&C) assay. Moreover, the mechanical properties and the ζ potential of CHg and CHg-TA were tested. The copper ion was selected as a pollutant model. The adsorption capacity (Qe) of CHg and CHg-TA was assessed as a function of pH. Under acidic conditions, CHg-TA shows a higher Qe than CHg through the coordination of copper ions by TA. At an alkaline pH, the phenols convert into a quinone form, decreasing the Qe of CHg-TA, and the performance of CHg was found to be improved. A partial TA release can occur in the copper solution due to its high hydrophilicity and strong acidic pH conditions. Additionally, the reusability of hydrogels was assessed, and the high number of recycling cycles of CHg-TA was related to its high mechanical performance (compression tests). These findings suggest CHg-TA as a promising green candidate for heavy metal ion removal from acidic wastewater.

Biobased hydrogels and their composite containing MgMOF74 for the removal of textile dyes and wastewater treatment

In this work, we report the synthesis of a biobased hydrogel comprised of collagen, chitosan, and polyurethane for the removal of textile dyes. The adsorption capacity of this hydrogel was improved by adding a magnesium metal-organic framework to the semi-interpenetrating polymer matrix yielding a composite hydrogel. Removal of Bismarck Brown and Congo red was studied, and the experimental results fit Freundlich's model. Both hydrogel formulations were tested for the removal of textiles dyes from wastewaters. The magnesium-metal organic framework improved the efficiency of the biobased hydrogel for the removal of direct and mordant dyes reaching up to 89 ± 2%. The composite hydrogel was tested for the removal of Congo Red in a fixed bed column observing the breakthrough point after 168 min. Also, a flocculant material was prepared from collagen and chitosan and was tested for the removal of direct red dye from wastewater removing up to 80 ± 1%. The pretreated wastewater by coagulation-flocculation was treated by adsorption yielding a global removal efficiency of 99%. Finally, the studied hydrogels are potentially biodegradable being completely degraded by the proteolytic action after 22 days. PRACTITIONER POINTS: Composite hydrogels of collagen, chitosan, and MgMOF74 removed efficiently textile dyes from wastewater in batch systems and fixed bed columns. A biobased flocculant of collagen and chitosan significantly improved water quality after coagulation flocculation. Hydrogels were reusable for four cycles, and they can be proteolytically degraded after 22 days.

Biodegradable polymers and their nano-composites for the removal of endocrine-disrupting chemicals (EDCs) from wastewater: A review

Endocrine-disrupting chemicals (EDCs) target the endocrine system by interfering with the natural hormones in the body leading to adverse effects on human and animal health. These chemicals have been identified as major polluting agents in wastewater effluents. Pharmaceuticals, personal care products, industrial compounds, pesticides, dyes, and heavy metals are examples of substances that could be considered endocrine active chemicals. In humans, these chemicals could cause obesity, cancer, Alzheimer's disease, autism, reproductive abnormalities, and thyroid problems. While in wildlife, dysfunctional gene expression could lead to the feminization of some aquatic organisms, metabolic diseases, cardiovascular risk, and problems in the reproductive system as well as its levels of hatchability and vitellogenin. EDCs could be effectively removed from wastewater using advanced technologies such as reverse osmosis, membrane treatment, ozonation, advanced oxidation, filtration, and biodegradation. However, adsorption has been proposed as a more promising and sustainable method for water treatment than any other reported technique. Increased attention has been paid to biodegradable polymers and their nano-composites as promising adsorbents for the removal of EDCs from wastewater. These polymers could be either natural, synthetic, or a combination of both. This review presents a summary of the most relevant cases where natural and synthetic biodegradable polymers have been used for the successful removal of EDCs from wastewater. It demonstrates the effectiveness of these polymers as favorable adsorbents for novel wastewater treatment technologies. Hitherto, very limited work has been published on the use of both natural and synthetic biodegradable polymers to remove EDCs from wastewater, as most of the studies focused on the utilization of only one type, either natural or synthetic. Therefore, this review could pave the way for future exploration of biodegradable polymers as promising and sustainable adsorbents for the removal of various types of pollutants from wastewater.

High-Performance Hydrogel Adsorbent Based on Cellulose, Hemicellulose, and Lignin for Copper(II) Ion Removal

Cellulose, hemicellulose, and lignin are three kinds of biopolymer in lignocellulosic biomass, and the utilization of the three biopolymers to synthesize hydrogel adsorbent could protect the environment and enhance the economic value of the biomass. A novel hydrogel adsorbent was prepared using cellulose, lignin, and hemicellulose of wheat straw by a one-pot method, and the adsorbent showed excellent adsorption performance for copper(II) ions. Scanning electron microscopy and Fourier transform infrared spectroscopy analysis showed that the prepared straw-biopolymer-based hydrogel had porous structure, and cellulose fibrils had crosslinked with lignin and hemicellulose by poly(acrylic acid) chains. The effects of contact time, initial concentration, and temperature on the copper(II) ion removal using the prepared hydrogels were investigated, and the obtained results indicated that the adsorption kinetics conformed to the pseudo-second-order and Elovich equation models and the adsorption isotherm was in accord with the Freundlich model. The adsorption thermodynamics study indicated that the adsorption process was spontaneous and accompanied by heat. X-ray photoelectron spectroscopy analysis revealed that the adsorption behavior resulted from ion exchange. The prepared hydrogel based on cellulose, hemicellulose, and lignin could be used for water treatment and soil remediation because of its high performances of excellent heavy metal ion removal and water retention.

Preparation of a double-network hydrogel based on wastepaper and its application in the treatment of wastewater containing copper(ii) and methylene blue

To reclaim and utilize wastepaper (WP), a WP/acrylamide double-network hydrogel (WP/PAM) was prepared to transform WP into efficient adsorbent for heavy metals and dye wastewater treatment. The structure and properties of the WP/PAM were characterized systematically by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), swelling performance (SR), Fourier transform infrared spectrum (FTIR), and X-ray photoelectron spectroscopy (XPS). Batch experiments showed that the adsorption process of Cu(ii) and MB followed the pseudo-second-order kinetic model and the Langmuir model. The maximum adsorption capacities of the WP/PAM for Cu(ii) and MB were 142.2 mg g⁻¹ and 1714.5 mg g⁻¹, respectively. The adsorption mechanism of Cu(ii) on the WP/PAM was related to ion exchange and complexation, while MB adsorption was driven by hydrogen bonding and electrostatic interaction. Besides, the WP/PAM performed well in treating simulated wastewater. The regeneration test indicated that the WP/PAM could be successfully reused after 6 cycles. This work provided an alternative choice for the recycling of WP and produced a potential adsorbent for the dye and heavy metals wastewater treatment.

In this research, wastepaper was innovatively compounded with acrylamide to prepare a wastepaper/acrylamide double-network hydrogel and was applied to the treatment of the mixed wastewater containing copper(ii) and methylene blue.

Removal of antibiotics from aqueous solution by using porous adsorbent templated from eco-friendly Pickering aqueous foams

The aqueous foam template without any solvent and only using the particles stabilizer has attracted much attention for preparation of the porous adsorbents. Herein, a novel porous adsorbent was fabricated via thermal-initiated polymerization of Pickering aqueous foams, which was stabilized by the natural sepiolite (Sep) and pine pollen, and utilized for the removal of antibiotic from aqueous solution. The stabilizing mechanism of Pickering aqueous foam of that the Sep was modified with the leaching substance from pine pollen and arranged orderly around the bubble to form a dense "shell" structure was revealed. The adsorbents possessed the hierarchical porous structure and excellent adsorption performance for antibiotic of chlorotetracycline hydrochloride (CTC) and tetracycline hydrochloride (TC). The equilibrium adsorption capacities of CTC and TC were achieved with 465.59 and 330.59 mg/g within 60 min at 25°C, respectively. The adsorption process obeyed Langmuir model and pseudo-second-order adsorption kinetic model. This work provided eco-friendly approach for fabricate porous adsorbents for wastewater treatment.

Cellulose-Based Hydrogels for Wastewater Treatment: A Concise Review

Finding affordable and environment-friendly options to decontaminate wastewater generated with heavy metals and dyes to prevent the depletion of accessible freshwater resources is one of the indispensable challenges of the 21st century. Adsorption is yet to be the most effective and low-cost wastewater treatment method used for the removal of pollutants from wastewater, while naturally derived adsorbent materials have garnered tremendous attention. One promising example of such adsorbents is hydrogels (HGs), which constitute a three-dimensional polymeric network of hydrophilic groups that is highly capable of adsorbing a large quantity of metal ions and dyes from wastewater. Although HGs can also be prepared from synthetic polymers, natural polymers have improved environmental benignity. Recently, cellulose-based hydrogels (CBHs) have been extensively studied owing to their high abundance, biodegradability, non-toxicity, and excellent adsorption capacity. This review emphasizes different CBH adsorbents in the context of dyes and heavy metals removal from wastewater following diverse synthesis techniques and adsorption mechanisms. This study also summarizes various process parameters necessary to optimize adsorption capacity followed by future research directions.

A systematic review on carbohydrate biopolymers for adsorptive remediation of copper ions from aqueous environments-Part B: Isotherms, thermokinetics and reusability

The presence of copper in aquatic environment is a serious threat for human health and ecosystem conservation. Adsorption is a powerful, operable and economic method for remediation of copper ions from aqueous phase. Carbohydrate biopolymers have emerged as promising, effective and environmental-friendly adsorbents for copper remediation. In part A of this review, different types of carbohydrate biopolymer adsorbents were surveyed focusing on prevalent and novel synthesis and modification methods. In current work (part B of the review), isothermal, thermodynamic and kinetic aspects of the copper adsorption by carbohydrate-based adsorbents as well as the regeneration and reusability of the biopolymer adsorbents are overviewed. Adsorption capacity, time required for equilibrium (adsorption rate), thermal-sensitivity of the adsorption, favorability extent, and sustainability of the adsorbents and adsorption processes are valuable and useful outcomes, resulted from the thermokinetic and reusability investigations. Such considerations are critical for the process design and scale up regarding technical, economical and sustainability of the adsorption process.

A Concise Review on the Physicochemical Properties of Biopolymer Blends Prepared in Ionic Liquids

An enhancement of environmental concern lately has improved the awareness of researchers in employing eco-friendly solvents for processing biopolymers. Recently, ionic liquids have been utilized to prepare biopolymer blends as they are non-volatile and recyclable. Biopolymers such as cellulose, chitin, chitosan, keratin, lignin, silk, starch, and zein are widely used for the preparation of biopolymer blends via dissolution in ionic liquids, followed by coagulation procedure. In this concise review, three types of ionic liquids based on imidazolium cations combined with different counter anions that are frequently utilized to prepare biopolymer blends are described. Moreover, three types of biopolymer blends that are prepared in ionic liquids were classified, specifically polysaccharide/polysaccharide blends, polysaccharide/polypeptide blends, and polysaccharide/bioplastic blends. The physicochemical properties of biopolymer blends prepared in different imidazolium-based ionic liquids are also concisely reviewed. This paper may assist the researchers in the polymer blend area and generate fresh ideas for future research.

Removal of a cationic dye from aqueous solution by a porous adsorbent templated from eco-friendly Pickering MIPEs using chitosan-modified semi-coke particles

Porous materials prepared from high internal phase emulsions have been attracting much attention in recent years, but two major defects related to the high consumption of organic solvent and surfactants are always difficult to solve.

Fabrication porous adsorbents templated from modified sepiolite-stabilized aqueous foams for high-efficient removal of cationic dyes

High internal phase emulsions (HIPEs) as template for fabrication of porous materials has attracted much attention, due to the high porosity and tunable porous structure. But the enormous consumption of organic solvents is still a nightmare for the practical application. In comparison, the aqueous foam without need any organic solvent and hence has greater advantages in the porous materials preparation. In this study, a novel Pickering foam which was stabilized by modified sepiolite (Sep) was prepared and applied as the template for preparation of the porous material via thermal-initiated polymerization. The Pickering foam had excellent ability and stability in the pH of 4-11 and the obtained porous adsorbent possess sufficient and tuned pore structure. The porous materials as adsorbent has favorable performance for adsorption and selective removal of cationic dyes, and the understanding adsorption capacities for Methylene blue (MB) and Methyl green (MG) can be achieved with 1421.18 mg/g and 638.81 mg/g within 60 and 45 min at 25 °C, respectively. This porous material can be as the potential adsorbent for adsorption or separation of organic pollutants.

An environmental-friendly magnetic bio-adsorbent for high-efficiency Pb(Ⅱ) removal: Preparation, characterization and its adsorption performance

In this paper, environmental friendly magnetic composite adsorbent (MSAL), exhibited excellent adsorption capacity for lead ions in the solution, was successfully prepared using two non-biologically toxic materials including L-cysteine and sodium alginate. Batch experiments were carried out to discuss the influences of different parameters like pH, adsorbent dosing, initial concentration and contact time on adsorption performance. Results showed sorption process followed by pseudo-second-order kinetic model and Langmuir isotherm model, which suggested the adsorption was limited by the chemical process dominated by the molecular layer. Based on Langmuir isotherm model, the maximum Pb(Ⅱ) adsorption capacity was about 330 mg/g, which was better than a large amount of other lead adsorbents. Various analytical methods, such as SEM-EDS, FTIR, VSM, TGA, XPS and Zeta potential, were applied to characterize the performance of this adsorbent as well as exploring the adsorption mechanism. Characterization results found this adsorbent exhibited a large contact area, good thermal stability, sufficient adsorption sites and excellent magnetic responsiveness. It also has been found that the adsorption mechanism mainly included ion exchange and chelation between amino, carboxyl and lead ions. After 5 cycles, the adsorption capacity decreased from 98.04% to 87.40% and still maintained at high level. The average iron ions concentration in the adsorbed solution sample or in the regeneration solution were 0.34 mg/L and 0.15 mg/L. Overall, all above results imply that MSAL is a promising reusable adsorbent for removing Pb(Ⅱ) in solution.

A systematic review on carbohydrate biopolymers for adsorptive remediation of copper ions from aqueous environments-part A: Classification and modification strategies

Copper is one of the most toxic heavy metals which must be eliminated from aqueous environments, according to the environmental standards. Carbohydrate biopolymers are promising candidates for synthesizing copper-adsorbent composites. It is due to unique properties such as having potential adsorptive functional sites, availability, biocompatibility and biodegradability, formability, blending capacity, and reusability. Different types of copper-adsorbent carbohydrate biopolymers like chitosan and cellulose with particular focus on the synthesizing and modification approaches have been tackled in this review. Composites, functionality and morphological aspects of the biopolymer adsorbents have also been surveyed. Further progress in the fabrication and application of biopolymer adsorbents would be achievable with special attention to some critical challenges such as the process economy, copolymer and/or (nano) additive selection, and the physicochemical stability of the biopolymer composites in aqueous media.

Preparation and Properties of Cellulose-Based Films Regenerated from Waste Corrugated Cardboards Using [Amim]Cl/CaCl2

1-Ally-3-methylimidazolium chloride ([Amim]Cl), dimethyl sulfoxide (DMSO), and CaCl₂ were selected to construct dissolution systems to produce value-added products from pretreatment of waste corrugated cardboards (P-WCCs). The dissolution behaviors of P-WCCs before and after ball milling were studied in different dissolution systems. The regenerated cellulose films were quickly and efficiently prepared via dissolving, regenerating, and pressurized drying. When 4 wt % waste corrugated cardboard was dissolved in [Amim]Cl for 4 h at 90 °C, the regenerated cellulose films featured tensile strengths as high as 59.00 MPa. Adding 40% DMSO and 2 wt % CaCl₂ increased the tensile strength of the film to a maximum value of 85.86 MPa. This demonstrates that DMSO improves the ability of WCC to dissolve in ionic liquids; Ca²⁺ improves the tensile strength and thermal stability of the regenerated cellulose film but reduces its transparency. This work provides a new, simple, and highly efficient way to use WCCs for packaging and wrapping.

Carboxymethyl cellulose-based cryogels for efficient heavy metal capture: Aluminum-mediated assembly process and sorption mechanism

Heavy metal ions pollution is a terrible issue that needs to be efficiently treated as a matter of priority to construct our sustainable society. However, the easy-to-handling of high-performance biomass-derived sorbents with fascinating features like high sorption capacity, favorable separation and recycling remain challenging. Herein, the development of a novel bead-like adsorbent with above features, that is, Al(III)-assembled carboxymethyl cellulose beads were used for the removal of Pb(II), Ni(II) and Co(II) from aqueous solution. Characterization methods like FT-IR, SEM, XPS and TGA were employed to confirm its physicochemical properties. Removal of the three heavy metal ions at different pH values, initial concentration and contact time were discussed at batch adsorption experiments. Meanwhile, regeneration was also discussed deeply. The results revealed that the adsorption capacity of the sorbents for three heavy metals increases with increasing pH and the initial concentration. The adsorption isotherm could be described well by the Freundlich model, and the maximum adsorption capacity for Pb(II), Ni(II) and Co(II) were 550, 620 and 760 mg/g, respectively. Kinetics study indicated that the Pseudo-second-order model described the best correlation with experimental data, this suggested that the complexation may participated in the adsorption process. More significantly, this type of bead-like adsorbents displayed excellent reusability after four sequential cycles.

Preparation of Carboxymethyl Cellulose-g- Poly(acrylamide)/Attapulgite Porous Monolith With an Eco-Friendly Pickering-MIPE Template for Ce(III) and Gd(III) Adsorption

Due to their high specific surface and metal-binding functional groups in their crosslinked polymeric networks, monolithic materials incorporating a porous structure have been considered one of the most efficient kinds of adsorbents for rare earth element recovery. Herein, a facile and novel monolithic multi-porous carboxymethyl cellulose-g-poly(acrylamide)/attapulgite was synthesized by free radical polymerization via green vegetable oil-in-water Pickering medium internal phase emulsion (O/W Pickering-MIPEs), which was synergically stabilized by attapulgite and tween-20. The homogenizer rotation speed and time were investigated to form stable Pickering-MIPEs. The effects of different types of oil phase on the formation of Pickering-MIPEs were investigated with stability tests and rheological characterization. The structure and composition of the porous material when prepared with eight kinds of vegetable oil were characterized by FTIR and SEM. The results indicate that the obtained materials, which have abundant interconnected porosity, are comparable to those fabricated with Pickering-HIPE templates. The adsorption experiment demonstrated that the prepared materials have a fast capture rate and high adsorption capacities for Ce(III) and Gd(III), respectively. The saturation adsorption capacities for Ce(III) and Gd(III) are 205.48 and 216.73 mg/g, respectively, which can be reached within 30 min. Moreover, the monolithic materials exhibit excellent regeneration ability and reusability. This work provides a feasible and eco-friendly pathway for the construction of a multi-porous adsorbent for adsorption and separation applications.

Modifying alginate beads using polycarboxyl component for enhanced metal ions removal

Designing desirable adsorbent for highly efficient removal of heavy metal ions is of practical significance, given the cost-effectiveness, environmental benign, natural abundance and easy-handling collection features. Herein, a bead-like adsorbent with high adsorption capacity was prepared by modifying alginate beads using polyacrylate with high density of carboxyl groups. The developed alginate/polyacrylate beads were collaboratively characterized by FT-IR, TGA, SEM, XPS, etc., and various adsorption conditions were tested including the pH of the solution, contact time and the initial concentration. The experimental data were fitted well by the Freundlich isotherm model, and the maximum adsorption capacity was obtained from the Langmuir model was 611.0 mg/g, and adsorption process followed the Pseudo-second-order kinetic model. The adsorption mechanisms conformed to multi-layer adsorption, and mainly dominated by chemical interactions. The bead-like adsorbent exhibited excellent reusability after eight sequential cycles and displayed higher adsorption capacity towards lead ions. This type of adsorbent might possess promising role in treating heavy metals from water by virtue of degradable, cost-effective component and high adsorption efficiency.

Synthesis of novel biocomposite powder for simultaneous removal of hazardous ciprofloxacin and methylene blue: Central composite design, kinetic and isotherm studies using Brouers-Sotolongo family models

Over the past decades, extensive efforts have been made to use biomass-based-materials for wastewater-treatment. The first purpose of this study was to develop and characterize regenerated-reed/reed-charcoal (RR-ChR), an enhanced biosorbent from Tunisian-reed (Phragmites-australis). The second aim was to assess and optimize the RR-ChR use for the removal of binary ciprofloxacin antibiotic (CIP) and methylene blue dye (MB), using Central Composite Design under Response Surface methodology. The third purpose was to explain the mechanisms involved in the biosorption-process. The study revealed that the highest removal-percentages (76.66 % for the CIP and 100 % for the MB) were obtained under optimum conditions: 1.55 g/L of adsorbent, 35 mg/L of CIP, 75 mg/L of MB, a pH of 10.42 and 115.28 min contact time. It showed that the CIP biosorption mechanism was described by Brouers-Sotolongo-fractal model, with regression-coefficient (R²) of 0.9994 and a Person's Chi-square (X²) of 0.01. The Hill kinetic model better described the MB biosorption (R² = 1 and X² = 1.0E-4). The isotherm studies showed that the adsorbent surface was heterogeneous and the best nonlinear-fit was obtained with the Jovanovich (R² = 0.9711), and Brouers-Sotolongo (R² = 0.9723) models, for the CIP and MB adsorption, respectively. Finally, the RR-ChR lignocellulosic-biocomposite-powder could be adopted as efficient and cost-effective adsorbent.

Compósitos en estado hidrogel con aplicación en la adsorción de metales pesados presentes en aguas residuales

La contaminación por metales pesados es un problema, que hoy en día no se ha logrado disminuir. Por esta razón, es necesario innovar constantemente las técnicas tradicionales con el fin de aplicar procesos eficientes que ayuden a remover los contaminantes e incluso recuperarlos para ser reincorporados a procesos productivos. En este contexto, la adsorción es una técnica tan versátil, que es viable su aplicación con materiales de diferentes características. Entre los materiales que han resultado adsorbentes eficientes, se encuentran las partículas inorgánicas y los polímeros/biopolímeros. Estos componentes por si solos presentan capacidades adsorbentes aceptables, pero en los últimos años se ha explorado la generación de matrices poliméricas en estado hidrogel reforzadas con materiales inorgánicos o mezclas de redes poliméricas generando compósitos, para mejorar o incrementar la capacidad de adsorción. Los hidrogeles compósitos conjugan una adsorción eficaz, buena área superficial específica y de fácil aplicabilidad, por lo que representan una gran alternativa para la disminución de los iones de metales pesados presentes en los ecosistemas acuáticos. Por este motivo, es la presente revisión de los materiales con propiedades adsorbentes, las estrategias para generar compósitos en estado hidrogel y sus propiedades adaptadas para la adsorción de iones de metales pesados, así como los retos y las áreas de oportunidad implícitos en esta generación de materiales innovadores. 

Enhanced phosphate removal using zirconium hydroxide encapsulated in quaternized cellulose

Zirconium-based materials are efficient adsorbent for aqueous phosphate removal. However, current zirconium-based materials still show unsatisfied performance on adsorption capacity and selectivity. Here, we demonstrate a zirconium hydroxide encapsulated in quaternized cellulose (QC-Zr) for the selective phosphate removal. Zirconium hydroxide nanoparticles were simultaneously generated in situ with the QC framework and firmly anchored in the three-dimensional (3D) cross-linked cellulose chains. The maximum P adsorption capacity of QC-Zr was 83.6 mg P/g. Furthermore, the QC-Zr shows high P adsorption performance in a wide pH range, generally due to the electrostatic effects of quaternized cellulose. The enhanced adsorption of P was also achieved in the presence of competing anions (including Cl^-, NO₃^-, SO₄^2-, SO₄^4-) and humic acid (HA) even at a molar ratio up to 20 levels. The column adsorption capacity of QC-Zr reached 4000 bed volumes (BV) at EBCT = 0.5 min as the P concentration decreased from 2.5 to 0.5 mg/L. Mechanism study revealed that both -N⁺(CH₃)₃ groups and zirconium hydroxide were involved in phosphate adsorption via electrostatic interactions between -N⁺(CH₃)₃ and phosphate, and the formation of zirconium hydrogen phosphate (Zr(HPO₄)x). The ³¹P nuclear magnetic resonance (NMR) study implied that P surface-precipitated and inner-sphere complexed with zirconium hydroxide at a ratio of 3:1.

A 3D porous microsphere with multistage structure and component based on bacterial cellulose and collagen for bone tissue engineering

Collagen (COL) and bacterial cellulose (BC) were chemically recombined by Malaprade and Schiff-base reactions. A three-dimensional (3D) porous microsphere of COL/BC/Bone morphogenetic protein 2 (BMP-2) with multistage structure and components were prepared by the template method combined with reverse-phase suspension regeneration. The microspheres were full of pores and had a rough surface. The particle size ranged from 8 to 12 microns, the specific surface area (S_BET) was 123.4 m²/g, the pore volume (V_Pore) was 0.59 cm³/g, and the average pore diameter (D_BJH) was 198.5 nm. The adsorption isotherm of the microspheres on the N₂ molecule belongs to that of mesoporous materials. The microspheres showed good biocompatibility, and the 3D porous microspheres with multiple structures and components effectively promoted the adhesion, proliferation, and osteogenic differentiation of mice MC3T3-E1 cells. The study can provide a theoretical basis for the application of COL/BC porous microspheres in the field of bone tissue engineering.

Preparation of Carboxymethyl Cellulose-Based Macroporous Adsorbent by Eco-Friendly Pickering-MIPEs Template for Fast Removal of Pb2+ and Cd2

Recently, Pickering high internal phase emulsions (Pickering HIPEs) have been widely used to fabricate macroporous materials. However, the high usage of poisonous organic solvent in HIPEs not only greatly increases the cost but also is harmful to human health and environment, which leads to limited large-scale applications. In this study, we prepared a novel monolithic macroporous material of carboxymethyl cellulose-g-poly(acrylamide)/montmorillonite (CMC-g-PAM/MMT) by the free radical polymerization via oil-in-water Pickering medium internal phase emulsions (Pickering MIPEs), which used the non-toxic and eco-friendly flaxseed oil as continuous phase, MMT, and Tween-20 (T-20) as stabilizer. The pore structure of the resulting macroporous materials could be tuned easily by adjusting the content of MMT, co-surfactant T-20, and the oil phase volume fraction. The maximal adsorption capacities of the prepared macroporous material for Pb²⁺ and Cd²⁺ were 456.05 and 278.11 mg/g, respectively, and the adsorption equilibrium can be reached within 30 min. Otherwise, the macroporous monolith exhibited excellent reusability through five adsorption–desorption cycles. Thus, the eco-friendly Pickering-MIPEs is a potential alternative method to be used to fabricate multi-porous adsorption materials for environmental applications.

Synthesis and fabrication of antibacterial hydrogel beads based on modified-gum tragacanth/poly(vinyl alcohol)/Ag0 highly efficient sorbent for hard water softening

In the current study, hard water softening for the removal of Ca²⁺ and Mg²⁺ ions was performed using hydrogel beads based on Gum Tragacance (GT) modified by using 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) and poly(vinyl alcohol). The antibacterial spherical hydrogel beads were fabricated by instantaneous gelation of well dispersed mixture of poly(AMPS)-g-GT (1 g), poly(vinyl alcohol) (PVA, 1 g) flocculent, green-synthesized silver metal nanoparticles (AgNPs, 10 mg), and graphene oxide (GO, 10 mg) in the acetone solution of boric acid and then transferring into the different amounts (0.5-2.5 mL) of acidic solution of glutaraldehyde (GA) as cross-linker. The beads were fully characterized and their adsorption behavior matched well with the pseudo-second-order kinetic and the Langmuir isotherm models with the maximum adsorption of Ca²⁺(114.18 mg g^-1) and Mg²⁺(162.46 mg g^-1). The removal ability of the beads decreased by 6% after four adsorption/desorption cycles. The antibacterial performance of the hydrogel beads was also investigated against Gram-positive and Gram-negative bacteria.

Proteins in Ionic Liquids: Reactions, Applications, and Futures

Biopolymer processing and handling is greatly facilitated by the use of ionic liquids, given the increased solubility, and in some cases, structural stability imparted to these molecules. Focussing on proteins, we highlight here not just the key drivers behind protein-ionic liquid interactions that facilitate these functionalities, but address relevant current and potential applications of protein-ionic liquid interactions, including areas of future interest.

Novel alginate/polyethyleneimine hydrogel adsorbent for cascaded removal and utilization of Cu2+ and Pb2+ ions

Heavy metal ion pollution leads to severe health risk to human beings. Herein, a natural and highly efficient sodium alginate (ALG)/polyethyleneimine (PEI) composite hydrogel was designed and fabricated for the removal of heavy metal ions from wastewater. The adsorption of heavy metal ions on the ALG based, 3D composite hydrogel were thoroughly investigated in this study. Furthermore, the in situ reduced metal nanoparticle-loaded ALG/PEI composite hydrogel provided us a sustainable utilization route of the heavy metal ion with a promising adsorption-catalysis ability. In general, this research will present an effective and practical paradigm for the cascaded treatment and recycling of heavy metal ions in wastewater.

Fabrication and Evaluation of Cellulose-Alginate-Hydroxyapatite Beads for the Removal of Heavy Metal Ions from Aqueous Solutions

In the present study, the potential of synthesized mixed cellulose, alginate and hydroxyapatite beads for the efficient removal of Ni (II) and Cu (II) ions from aqueous solutions was investigated. Cellulose, alginate and hydroxyapatite are known for their individual adsorption capacity. Beads were prepared in different ratios of these materials. The prepared beads were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and thermogravimetric analysis (TGA). FTIR and XRD analysis showed characteristic peaks assigned to cellulose, alginate and hydroxyapatite. Thermal stability was observed to increase with increase of hydroxyapatite percentage in beads. SEM images showed increased surface porosity and roughness with the increase of cellulose percentage. The prepared beads were used for the removal of Ni (II) and Cu (II) ions from aqueous solutions and the process was optimized with respect to pH, contact time, adsorbent dose and initial concentration of metal ions. The values of the coefficient of determination (R2) of the Langmuir and Freundlich adsorption model indicated that the adsorbed Cu (II) and Ni (II) ions form monolayer coverage on the adsorbent surface. In kinetic analysis, Pseudo-second-order model fitted the kinetic experimental data well, as it showed high R2 value; above 0.9990.

Mesenchymal stem cells associated with chitosan scaffolds loaded with rosuvastatin to improve wound healing

In this study we explored the role of rosuvastatin calcium in skin regeneration as statins play important role in the field of tissue engineering. Chitosan hydrochloride was crosslinked with different weight ratios of collagen, β-glycerolphosphate and carboxymethyl cellulose to produce scaffolds by lyophilization technique. Subsequently, the fabricated scaffolds were examined for their morphology, water absorption capacity, water retention, friability and in-vitro drug release as well as in-vivo studies. The results revealed porous 3-D structured scaffolds with maximum water absorption values-ranging between 396 and 2993%. Scaffolds containing carboxymethyl cellulose revealed highest water absorption-values. In-vitro drug release results showed gradual drug release for 60 h with mean dissolution time-values (MDT) between 13 and 21 h. Combination of chitosan, collagen, carboxymethyl cellulose in weight ratio of 40:30:30, respectively achieved gradual disintegration of the scaffold in a simulating medium to an open wound after 4 days. This selected scaffold loaded with rosuvastatin revealed increase proliferation of human dermal fibroblasts compared to placebo scaffold. After 30 days of implantation of selected medicated scaffold loaded with/without mesenchymal stem cells and placebo scaffolds to induced wounds in Albino rats, enhanced skin regeneration and absence of scar formation for drug loaded scaffolds were observed. The histopathological study showed the advantage of stem cells-loaded scaffolds through the normal redistribution of collagen in the epidermal layer. In conclusion, rosuvastatin calcium and stem cells loaded in the tested scaffolds proved their potential effect in enhancing skin healing and regeneration.

Preparation of novel multi-walled carbon nanotubes nanocomposite adsorbent via RAFT technique for the adsorption of toxic copper ions

In the present work, polymer-coated multiwalled carbon nanotube (MWCNT) was prepared via RAFT method. First, a novel trithiocarbonate-based RAFT agent was prepared attached chemically into the surface of MWCNT. In addition, the RAFT co-polymerization of acrylic acid and acrylamide monomers was conducted through the prepared RAFT agent. In the next age, the surface morphology and chemical properties of the prepared components were fully examined by using FTIR, ¹HNMR, SEM, TEM, XRD and TGA/DTG techniques. Finally, the modified MWCNT composite was employed as an excellent adsorbent for the adsorption of copper (II) ions. The results indicated that ion adsorption basically relies on adsorbing time, solution pH, initial copper concentration, and adsorbent dosage. Further, the adsorption kinetics and isotherm analysis demonstrated that the adsorption mode was fitted with the pseudo-second-order and Langmuir isotherm models, respectively. Based on the results of thermodynamic study, the ion adsorption process was endothermic and spontaneous. Finally, based on the experimental results, the surface functionalized MWCNT with hydrophilic groups could be successfully used as a promising selective adsorbent material in wastewater treatment.

Biopolymer-Based Composite Materials Prepared Using Ionic Liquids

Biopolymer-based composite materials have many potential applications in biomedical, pharmaceutical, environmental, biocatalytic, and bioelectronic fields, owing to their inherent biocompatibility and biodegradability. When used as solvents, ionic liquids can be used to fabricate biopolymers such as polysaccharides and proteins into various forms, including molded shapes, films, fibers, and beads. This article summarizes the processes for preparing biopolymer-based composite materials using ionic liquids. The processes include biopolymer dissolution using ionic liquids, regeneration of the biopolymer by an anti-solvent, formation of shapes, and drying of the regenerated biopolymer. In particular, the preparation and applications of biopolymer blend-based composite materials containing two or more biopolymers are addressed.

Free radical synthesis of nanosilver/gelatin-poly (acrylic acid) nanocomposite hydrogels employed for antibacterial activity and removal of Cu(II) metal ions

The present work involves the synthesis of porous gelatin/AcA (PGE-AcA) hydrogel and novel porous gelatin-silver/AcA (NPGESNC-AcA) nanocomposite hydrogel, and their ability as effective biosorbents for the removal of Cu²⁺ ions from contaminated water. The formation of the samples was confirmed by UV-Vis, TEM, SEM, EDX, DLS, AFM, XRD, TGA/DTG and FTIR techniques. The adsorption studies results showed that maximum monolayer adsorption capacity of copper ions for PGE-AcA was achieved about 130.50 mg g^-1 in pH 6.0 for 50 min, and adsorption capacity for the NPGESNC-AcA was nearly 147.10 mg g^-1 in pH 5.5 for 40 min by atomic absorption spectroscopy technique. The Cu²⁺ ions loaded on the PGE-AcA and NPGESNC-AcA could be recovered by HCl above 65.8% and 78.7% after five consecutive cycles of adsorption/desorption, respectively. The results showed that the both of biosorbents loaded by Cu²⁺ ions could be easily regenerated and reusable. On the other hand, the results of adsorption kinetics and equilibrium isotherms were indicated high correlation coefficient (closer to a unit) for the pseudo-second-order and excellent fitted the adsorption data with the Langmuir isotherm model. Furthermore, the antimicrobial efficiency of the synthesized samples were tested on the Staphylococcus aureus and the Escherichia coli.

Environment-friendly wood fibre composite with high bonding strength and water resistance

With the growing depletion of wood-based materials and concerns over emissions of formaldehyde from traditional wood fibre composites, there is a desire for environment-friendly binders. Herein, we report a green wood fibre composite with specific bonding strength and water resistance that is superior to a commercial system by using wood fibres and chitosan-based adhesives. When the mass ratio of solid content in the adhesive and absolute dry wood fibres was 3%, the bonding strength and water resistance of the wood fibre composite reached the optimal level, which was significantly improved over that of wood fibre composites without adhesive and completely met the requirements of the Chinese national standard GB/T 11718-2009. Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) characterizations revealed that the excellent performance of the binder might partly be due to the amide linkages and hydrogen bonding between wood fibres and the chitosan-based adhesive. We believe that this strategy could open new insights into the design of environment-friendly wood fibre composites with high bonding strength and water resistance for multifunctional applications.

Effective removal of copper from aqueous solutions by modified magnetic chitosan/graphene oxide nanocomposites

In the present work, a novel magnetic chitosan/graphene oxide nanocomposite (MCGON) was synthesized for the removal of Cu²⁺ from aqueous solutions. The adsorbent was composed of graphene oxide (GO) modified by ethylenediamine (ED), Fe₃O₄ nanoparticles and chitosan-g-poly(acrylic acid-co-2-acrylamido-2-methylpropane sulfonic acid) copolymer. The composition and structure of adsorbents were characterized by FTIR, SEM, EDX, XRD, TGA, VSM and BET analysis. The magnetic MCGON with a high specific surface area of (132.9m²g^-1), large pore volume (4.03cm³g^-1), small particle size (15nm) and strong saturation magnetization (3.82emug^-1) was used as an efficient adsorbent for the removal of Cu²⁺ ions from wastewater. The results showed that the adsorption of Cu²⁺ onto MCGON exhibited a maximum adsorption capacity of 217.4mgg^-1. Kinetics, thermodynamics and equilibrium isotherm of the removal of copper (II) ions were carefully investigated. Adsorption of Cu²⁺ onto nanocomposite followed pseudo-second-order and Langmuir isotherm models. Thermodynamic parameters exhibited that the sorption process was feasible, spontaneous and endothermic in nature. These results provide evidences for the efficient removal of heavy metals from industrial wastewater.