Treatment characteristics of microplastics at biological sewage treatment facilities in Korea

Microplastics in aquatic systems: an in-depth review of current and potential water treatment processes

Plastic products, despite their undeniable utility in modern life, pose significant environmental challenges, particularly when it comes to recycling. A crucial concern is the pervasive introduction of microplastics (MPs) into aquatic ecosystems, with deleterious effects on marine organisms. This review presents a detailed examination of the methodologies developed for MPs removal in water treatment systems. Initially, investigating the most common types of MPs in wastewater, subsequently presenting methodologies for their precise identification and quantification in aquatic environments. Instruments such as scanning electron microscopy, dynamic light scattering, Fourier transform infrared spectroscopy, Raman spectroscopy, surface-enhanced Raman spectroscopy, and Raman tweezers stand out as powerful tools for studying MPs. The discussion then transitions to the exploration of both existing and emergent techniques for MPs removal in wastewater treatment plants and drinking water treatment plants. This includes a description of the core mechanisms that drive these techniques, with an emphasis on the latest research developments in MPs degradation. Present MPs removal methodologies, ranging from physical separation to chemical and biological adsorption and degradation, offer varied advantages and constraints. Addressing the MPs contamination problem in its entirety remains a significant challenge. In conclusion, the review offers a succinct overview of each technique and forwards recommendations for future research, highlighting the pressing nature of this environmental dilemma.

Aging and mitigation of microplastics during sewage sludge treatments: An overview

Wastewater treatment plants (WWTPs) receive large quantities of microplastics (MPs) from raw wastewater, but many MPs are trapped in the sludge. Land application of sludge is a significant source of MP pollution. Existing reviews have summarized the analysis methods of MPs in sludge and the effect of MPs on sludge treatments. However, MP aging and mitigation during sludge treatment processes are not fully reviewed. Treatment processes used to remove water, pathogenic microorganisms, and other pollutants in sewage sludge also cause surface changes and degradation in the sludge MPs, affecting the potential risk of MPs. This study integrates MP abundance and distribution in sludge and their aging and mitigation characteristics during sludge treatment processes. The abundance, composition, and distribution of sludge MPs vary significantly with WWTPs. Furthermore, MPs exhibit variable degrees of aging, including rough surfaces, enhanced adsorption potentials for pollutants, and increased leaching behavior. Various sludge treatment processes further intensify these aging characteristics. Some sludge treatments, such as hydrothermal treatment, have efficiently removed MPs from sewage sludge. It is crucial to understand the potential risk of MP aging in sludge and the degradation properties of the MP-derived products from MP degradation in-depth and develop novel MP mitigation strategies in sludge, such as combining hydrothermal treatment and biological processes.

Microplastic contamination in wastewater: Sources, distribution, detection and remediation through physical and chemical-biological methods

Microplastics are tiny plastic particles smaller than 5 mm. that have been widely detected in the environment, including in wastewater. They originate from various sources including breakdown of larger plastic debris, release of plastic fibres from textiles, and microbeads commonly used in personal care products. In wastewater, microplastics can pass through the treatment process and enter the environment, causing harm to biodiversity by potentially entering the food chain. Additionally, microplastics can act as a vector for harmful pollutants, increasing their transport and distribution in the environment. To address this issue, there is a growing need for effective wastewater treatment methods that can effectively remove microplastics. Currently, several physical and chemical methods are available, including filtration, sedimentation, and chemical degradation. However, these methods are costly, low efficiency and generate secondary pollutants. Furthermore, lack of standardization in the measurement and reporting of microplastics in wastewater, makes it difficult to accurately assess microplastic impact on the environment. In order to effectively manage these issues, further research and development of effective and efficient methods for removing microplastics from wastewater, as well as standardization in measurement and reporting, are necessary to effectively manage these detrimental contaminants.

Comprehensive assessment of microplastics in Australian biosolids: Abundance, seasonal variation and potential transport to agroecosystems

Striving towards a circular economy, the application of treated sewage sludge (biosolids) to land is an opportunity to improve the condition of the soil and add essential nutrients, in turn reducing the need for fertilisers. However, there is an increasing concern about microplastic (MP) contamination of biosolids and their transport to terrestrial ecosystems. In Australia, agriculture is the largest biosolids end-user, however, there is limited understanding of MPs in Australian biosolids. Also, while the method to isolate MPs from biosolid is established, a need to extract and analyse MPs more efficiently is still pressing. In this study, we comprehensively quantified and characterised MPs in 146 biosolids samples collected from thirteen wastewater treatment plants (WWTPs) including different seasons. We have optimised an oxidative-enzymatic purification method to overcome current limitations for MP identification in complex samples and accurately report MPs in biosolids. This method enabled removal of >93 % of dry weight of organic material and greatly facilitated the MPs instrumental analysis. The concentration of MPs (>20 µm) in all biosolids samples ranged from 11 to 150 MPs/g dry weight. Abundance of MPs was affected by seasons with higher abundance of MPs usually found during cold and wet seasons. Despite seasonal variations, polyethylene terephthalate, polyurethane and polymethyl methacrylate were the most abundant polymers. Smaller MPs (20 to 200 µm) comprised >70 % of all detected MPs with a clear negative linear relationship observed between MP size and abundance. Per capita concentration of MPs in biosolids across all studied WWTPs was 0.7 to 21 g MPs per person per year. Therefore, biosolids are an important sink and source of MPs to agroecosystems, emphasising the need to more comprehensively understand the fate, impact and risks associated with MPs on agricultural soils.

Microalgal-based industry vs. microplastic pollution: Current knowledge and future perspectives

Microalgae can play a crucial role in the environment due to their efficient capture of CO2 and their potential as a solution for a carbon-negative economy. Water quality is critical for the success and profitability of microalgal-based industries, and understanding their response to emergent pollutants, such as microplastics (MPs), is essential. Despite the published studies investigating the impact of MPs on microalgae, knowledge in this area remains limited. Most studies have mainly focused on microalgal growth, metabolite analysis, and photosynthetic activity, with significant discrepancies in what is known about the impact on biomass yield. Recent studies show that the yield of biomass production depends on the levels of water contamination by MPs, making it necessary to reduce the contamination levels in the water. However, present technologies for extracting and purifying water from MPs are limited, and further research and technological advancements are required. One promising solution is the use of bio-based polymer materials, such as bacterial cellulose, which offer biodegradability, cost-effectiveness, and environmentally friendly detoxifying properties. This review summarises the current knowledge on MPs pollution and its impact on the viability and proliferation of microalgae-based industries, highlights the need for further research, and discusses the potential of bio-solutions for MPs removal in microalgae-based industries.

Microplastic particles in river sediments and water of southwestern Nigeria: insights on the occurrence, seasonal distribution, composition, and source apportionment

Microplastics (MPs) are globally recognized as an emerging environmental threat, particularly in the aquatic environment. This study presents baseline data on the occurrence and distribution of MPs in sediments and surface water of major rivers in southwestern Nigeria. Microplastics were extracted by density separation and polymer identification using Fourier transformed infrared spectroscopy in attenuated total reflectance mode (FTIR-ATR). The abundance of MPs in surface sediment and water samples across all locations ranged from 12.82 to 22.90 particle/kg dw and 6.71 to 17.12 particle/L during the dry season and 5.69 to 14.38 particle/kg dw and 12.41 to 22.73 particle/L during the wet season, respectively. On average, fiber constituted the highest percentage of MP in sediments (71%) and water (67%) while foam accounted for the lowest values of 0.6% and 1.7%, respectively. Polypropylene (PP) and polyethylene (PE) were the main MPs across all locations based on Fourier transform infrared spectroscopy (FTIR). MPs of size < 1 mm were the most abundant (≥ 55%) on average in both water and sediments. The study identified run-off from human activities and industrial wastewater as potential sources of MP exposure based on positive matrix factorization. The study suggests assessing the impact of different land-use activities on MPs occurrence and distribution in addition to quantifying MPs in seafood as a way forward in food safety management systems for further studies. This study confirmed the occurrence and widespread distribution of MPs in surface water and sediments and provides a database on MP pollution in Nigeria.

Abundance, characterization, and removal of microplastics in different technology-based sewage treatment plants discharging into the middle stretch of the Ganga River, India

Sewage treatment plants (STPs) are considered as a prominent source for releasing microplastics (MPs) into the riverine systems. Though MPs abundance and removal efficacy in different secondary treatment technique-based STPs have been extensively studied worldwide, such studies are scarce in Indian conditions. Herein, this study comprehensively assesses MPs abundance, characterization, and their removal in the selected secondary treatment technique-based STPs discharging into the middle stretch of the Ganga River in India. MPs concentration (n/L) in influent and effluent of the STPs varied between 42 ± 10 to 150 ± 19 and 3 ± 1 to 22 ± 5, respectively. Overall, the primary treatment stage was observed to remove MPs by 23-42 %, while the secondary treatment stage removed MPs by 67-90 %. Selected technique-based STPs exhibited varying MPs removal efficacies as follows: SBR (94 %), TF (90 %), AL (88 %), UASB (87 %), ASP (85 %), FAB (84 %), and Bio-tower (77 %). MPs ranging from 50 to 250 μm were the dominant sizes, with PP, PE, and PS being the prevalent polymers. The Ganga River receives about 3 × 108 MPs/day from STP effluents, and an estimated 4.5 × 107 MPs/day are released via the sludge. This comprehensive assessment of MPs abundance and removal from different technology-based Indian STPs will allow the comparison of the generated dataset with similar studies worldwide.

Can microplastics and disinfectant resistance genes pose conceivable threats to water disinfection process?

Microplastic pollution in the environment has aroused widespread concerns, however, the potential environmental risks caused by excessive use of disinfectants are still unknown. Disinfectants with doses below the threshold can enhance the communication of resistance genes in pathogenic microorganisms, promoting the development and spread of antimicrobial activity. Problematically, the intensification of microplastic pollution and the increase of disinfectant consumption will become a key driving force for the growth of disinfectant resistance bacteria (DRB) and disinfectant resistance genes (DRGs) in the environment. Disinfection plays a crucial role in ensuring water safety, however, the presence of microplastics and DRGs seriously disturb the water disinfection process. Microplastics can reduce the concentration of disinfectant in the local environment around microorganisms and improve their tolerance. Microorganisms can improve their resistance to disinfectants or generate resistance genes via phenotypic adaptation, gene mutations, and horizontal gene transfer. However, very limited information is available on the impact of DRB and DRGs on disinfection process. In this paper, the contribution of microplastics to the migration and transmission of DRGs was analyzed. The challenges posed by the presence of microplastics and DRGs on conventional disinfection were thoroughly discussed. The knowledge gaps faced by relevant current research and further research priorities have been proposed in order to provide a scientific basis in the future.

Microplastics removal technologies from aqueous environments: a systematic review

Purpose

Pollution of the environment with all kinds of plastics has become a growing problem. The problem of microplastics is mainly due to the absorption of stable organic pollutants and metals into them, and as a result, their environmental toxicity increases. The main purpose of this study is to investigate the appropriate and efficient methods of removing microplastics from aqueous environments through a systematic review.

Methods

Present study designed according to PRISMA guidelines. Two independent researchers followed all process from search to final analysis, for the relevant studies using international databases of PubMed, Scopus and ISI/WOS (Web of Science), without time limit. The search strategy developed based on the main axis of "microplastics", "aqueous environments" and "removal". This research was carried out from 2017 until the March of 2022. All relevant observational, analytical studies, review articles, and a meta-analysis were included.

Results

Through a comprehensive systematic search we found 2974 papers, after running the proses of refining, 80 eligible papers included to the study. According to the results of the review, the methods of removing microplastics from aquatic environments were divided to physical (12), chemical (18), physicochemical (27), biological (12) and integrated (11) methods. In different removal methods, the most dominant group of studied microplastics belonged to the four groups of polyethylene (PE), polystyrene (PS), polypropylene (PP) and polyethylene tetra phthalate (PET). Average removal efficiency of microplastics in different processes in each method was as: physical method (73.76%), chemical method (74.38%), physicochemical method (80.44%), biological method (75.23%) and integrated method (88.63%). The highest removal efficiency occurred in the processes based on the integrated method and the lowest efficiency occurred in the physical method. In total, 80% of the studies were conducted on a laboratory scale, 18.75% on a full scale and 1.25% on a pilot scale.

Conclusion

According to the findings; different processes based on physical, chemical, physicochemical, biological and integrated methods are able to remove microplastics with high efficiency from aqueous environments and in order to reduce their hazardous effects on health and environment, these processes can be easily used.

A standard analytical approach and establishing criteria for microplastic concentrations in wastewater, drinking water and tap water

The ubiquitous presence of microplastics (MPs) in natural water bodies reflects the global issue regarding these micropollutants. The main problem of MPs lies on the difficulty of removing these particles from water during wastewater and drinking water treatments. The release of MPs to the environment in treated wastewater contributed to the dispersion of these micropollutants, which enhances the harmful effect of MPs on fauna and flora. In addition, their presence in tap water entails a potential risk to human health since MPs can be directly consumed. The first step is being able to quantify and characterise these microparticles accurately. In this work, a comprehensive analysis on the presence of MPs in wastewater, drinking water and tap water has been conducted with emphasis on sampling methods, pre-treatment, MP size and analytical methods. Based on literature data, a standard experimental procedure has been proposed with the objective of recommending a methodology that allows the homogenisation of MP analysis in water samples. Finally, reported MP concentrations for influents and effluents of drinking and wastewater treatment plants and tap water have been analysed, in terms of abundance, ranges and average values, and a tentative classification of different waters based on their MP concentrations is proposed.

Process analysis of microplastic aging during the photochemical oxidation process and its effect on the adsorption behavior of dissolved organic matter

Information on microplastics (MPs) interactions with dissolved organic matter (DOM) is essential for understanding their environmental impacts. However, research is scarce regarding the adsorption behavior of DOM with different characteristics onto pristine and aged MPs. This research thus investigates MPs aging behavior accelerated by UV/Persulfate and UV/chlorine oxidation processes and the adsorption behavior of organic matter with low-specific ultraviolet absorbance (L-SUVA) and high-SUVA (H-SUVA) characteristics. MPs were degraded by UV/Cl and UV/Persulfate for 30 days. Changes in thermal properties, surface morphology, and chemistry were studied using different analytical techniques. The adsorption behavior was assessed by adsorption kinetic and isotherm study. After oxidation, the surface of the MPs showed a significant increase in the oxygen-containing functional groups, contact angle, surface roughness, and surface energy, and a decrease in crystallinity. The oxidation effect follows the order of UV/Cl > UV/Persulfate. The kinetic and equilibrium data of H-SUVA adsorption on pristine and aged MPs well-fitted the pseudo-second-order and Langmuir model. In contrast, L-SUVA well-fitted the pseudo-first-order and Freundlich model. The adsorption capacity (qm) increased in the following orders: 8.11 > 5.87>4.29 mg g-1 for H-SUVA and 19.81 > 6.662>5.315 mg g-1 for L-SUVA by MPs aged with UV/Cl, UV/Persulfate and pristine MPs, respectively. The larger the surface damage of MPs, the greater the adsorption affinity of DOM. The result was attributed to the physical adsorption process, hydrophobic interactions, electrostatic, hydrogen, and halogen bonding. These findings are beneficial to provide new insights involving the adsorption behavior and interaction mechanisms of DOM onto MPs for the environmental risk assessment.

Microplastics' Shape and Morphology Analysis in the Presence of Natural Organic Matter Using Flow Imaging Microscopy

Ubiquitous microplastics in urban waters have raised substantial public concern due to their high chemical persistence, accumulative effects, and potential adverse effects on human health. Reliable and standardized methods are urgently needed for the identification and quantification of these emerging environmental pollutants in wastewater treatment plants (WWTPs). In this study, we introduce an innovative rapid approach that employs flow imaging microscopy (FlowCam) to simultaneously identify and quantify microplastics by capturing high-resolution digital images. Real-time image acquisition is followed by semi-automated classification using customized libraries for distinct polyethylene (PE) and polystyrene (PS) microplastics. Subsequently, these images are subjected to further analysis to extract precise morphological details of microplastics, providing insights into their behavior during transport and retention within WWTPs. Of particular significance, a systematic investigation was conducted to explore how the presence of natural organic matter (NOM) in WWTPs affects the accuracy of the FlowCam's measurement outputs for microplastics. It was observed that varying concentrations of NOM induced a more curled shape in microplastics, indicating the necessity of employing pre-treatment procedures to ensure accurate microplastic identification when utilizing the FlowCam. These observations offer valuable new perspectives and potential solutions for designing appropriate treatment technologies for removing microplastics within WWTPs.

Potential transmission of SARS-CoV-2 through microplastics in sewage: A wastewater-based epidemiological review

In light of the current COVID-19 pandemic caused by the virus SARS-CoV-2, there is an urgent need to identify and investigate the various pathways of transmission. In addition to contact and aerosol transmission of the virus, this review investigated the possibility of its transmission via microplastics found in sewage. Wastewater-based epidemiological studies on the virus have confirmed its presence and persistence in both influent sewage as well as treated ones. The hypothesis behind the study is that the huge amount of microplastics, especially Polyvinyl Chloride and Polyethylene particles released into the open waters from sewage can become a good substrate and vector for microbes, especially Polyvinyl Chloride and Polyethylene particles, imparting stability to microbes and aiding the "plastisphere" formation. A bibliometric analysis highlights the negligence of research toward plastispheres and their presence in sewage. The ubiquity of microplastics and their release along with the virus into the open waters increases the risk of viral plastispheres. These plastispheres may be ingested by aquatic organisms facilitating reverse zoonosis and the commercial organisms already reported with accumulating microplastics through the food chain poses a risk to human populations as well. Reliance of high population density areas on open waters served by untreated sewage in economically less developed countries might bring back viral transmission.

Degradation mechanism of microplastics and potential risks during sewage sludge co-composting: A comprehensive review

Microplastics (MPs) as a kind of emerging contaminants, widely exists in various kinds of medium, sewage sludge (SS) is no exception. In the sewage treatment process, a large number of microplastics will be deposited in SS. More seriously, microplastics in sewage sludge can migrate to other environmental media and threaten human health. Therefore, it is necessary to remove MPs from SS. Among the various restorations, aerobic composting is emerging as a green microplastic removal method. There are more and more reports of using aerobic compost to degrade microplastics. However, there are few reports on the degradation mechanism of MPs in aerobic composting, hindering the innovation of aerobic composting methods. Therefore, in this paper, the degradation mechanism of MPs in SS is discussed based on the environmental factors such as physical, chemical and biological factors in the composting process. In addition, this paper expounds the MPs in potential hazards, and combined with the problems in the present study were studied the outlook.

Detection of microplastic traces in four different types of municipal wastewater treatment plants through FT-IR and TED-GC-MS

Large amounts of microplastics are discharged into wastewater treatment plants (WWTPs), from where some of them are released into natural waterbodies on account of their not being fully eliminated by WWTPs. To investigate the behavior and emission of microplastics from WWTPs, we selected four WWTPs with different treatment technologies, including anaerobic-anoxic-aerobic (A2O), sequence batch reactor (SBR), media, and membrane bioreactor (MBR). The number of microplastics detected using Fourier transform infrared (FT-IR) spectroscopy ranged from 520 to 1820 particles/L in influent and from 0.56 to 2.34 particles/L in effluent. The microplastic removal efficiencies of four WWTPs were over 99%, indicating that the type of treatment technologies did not significantly affect the removal rate of microplastics. In the unit process for each WWTP, the major stages relating to microplastic removal were the secondary clarifier and tertiary treatment processes. Most microplastics detected were categorized as fragments and fibers, while other types were hardly detected. The size of more than 80% of microplastic particles detected in WWTPs ranged between 20 and 300 μm, indicating that they were significantly smaller than the size threshold defined for microplastics. Therefore, we used thermal extraction-desorption coupled with gas chromatography-mass spectroscopy (TED-GC-MS) to evaluate the microplastic mass content in all four WWTPs, and the results were compared with those of the FT-IR analysis. In this method, only four components, namely polyethylene, polypropylene, polystyrene, and polyethylene terephthalate, were analyzed because of the analysis limitation, and the total microplastic concentration represented the sum of four components concentrations. The influent and effluent microplastic concentrations estimated by TED-GC-MS ranged from not detectable to 160 μg/L and 0.04-1.07 μg/L, respectively, indicating a correlation coefficient of 0.861 (p < 0.05) between the TED-GC-MS and FT-IR results, when compared to the combined abundance of the four microplastic components by FT-IR analysis.

Microplastics in aquatic environments: A comprehensive review of toxicity, removal, and remediation strategies

The occurrence of microplastics (MPs) in aquatic environments has been a global concern because they are toxic and persistent and may serve as a vector for many legacies and emerging pollutants. MPs are discharged to aquatic environments from different sources, especially from wastewater plants (WWPs), causing severe impacts on aquatic organisms. This study mainly aims to review the Toxicity of MPs along with plastic additives in aquatic organisms at various trophic compartments and available remediation methods/strategies for MPs in aquatic environments. Occurrences of oxidative stress, neurotoxicity, and alterations in enzyme activity, growth, and feeding performance were identical in fish due to MPs toxicity. On the other hand, growth inhibition and ROS formation were observed in most of the microalgae species. In zooplankton, potential impacts were acceleration of premature molting, growth retardation, mortality increase, feeding behaviour, lipid accumulation, and decreased reproduction activity. MPs togather with additive contaminants could also exert some toxicological impacts on polychaete, including neurotoxicity, destabilization of the cytoskeleton, reduced feeding rate, growth, survivability and burrowing ability, weight loss, and high rate of mRNA transcription. Among different chemical and biological treatments for MPs, high removal rates have been reported for coagulation and filtration (>86.5 %), electrocoagulation (>90 %), advanced oxidation process (AOPs) (30 % to 95 %), primary sedimentation/Grit chamber (16.5 % to 58.84 %), adsorption removal technique (>95 %), magnetic filtration (78 % to 93 %), oil film extraction (>95 %), and density separation (95 % to 100 %). However, desirable extraction methods are required for large-scale research in MPs removal from aquatic environments.

Microplastics as emergent contaminants in landfill leachate: Source, potential impact and remediation technologies

A significant amount of plastic waste is generated each year on a global scale, in which the maximum quantity of plastic waste is typically dumped in landfills in various parts of the world. Moreover, dumping plastic waste in landfills cannot address the issue of proper disposal; it simply delays the process. Exploiting waste resources entails environmental hazards because plastic wastes buried in landfills gradually break down into Microplastics (MPs) due to physical, chemical, and biological effects. The possibility of landfill leachate as a source of MPs in the environment has not received much attention. Without systematic treatment, MPs in leachate increase the risk to human health and environmental health since they contain dangerous and toxic pollutants and antibiotic resistance genes transmitted by leachate vectors. Due to their severe environmental risks, MPs are now widely recognized as emerging pollutants. Therefore, the composition of MPs in landfill leachate and the interaction of MPs with other hazardous contaminants are summarised in this review. The available potential mitigation or treatment methods of MPs in landfill leachate as of now, along with the drawbacks and challenges of the present leachate treatment for eliminating MPs, are described in this review. Since it is unclear how MPs will be removed from the current leachate facilities, it is crucial to develop innovative treatment facilities as quickly as possible. Finally, the areas that require more research to provide complete solutions to the persistent problem of plastic debris are discussed.

Nano and microplastics occurrence in wastewater treatment plants: A comprehensive understanding of microplastics fragmentation and their removal

Nano/microplastic (NP/MP) pollution is a growing concern for the water environment. Wastewater treatment plants (WWTPs) are considered the major recipients of MP before discharging into local waterbodies. MPs enter WWTPs mainly from synthetic fibers through washing activities and personal care products. To control and prevent NP/MP pollution, it is essential to have a comprehensive understanding of their characteristics, fragmentation mechanisms, and the effectiveness of the current treatment processes used in WWTPs for NP/MP removal. Therefore, the objectives of this study are to (i) understand the detailed mapping of NP/MP in the WWTP, (ii) understand the fragmentation mechanisms of MP into NP, and (iii) investigate the removal efficiency of NP/MP by existing processes in the WWTP. This study found that fiber is the dominant shape of MP, and polyethylene, polypropylene, polyethylene terephthalate, and polystyrene are the major polymer type of MP in wastewater samples. Crack propagation and mechanical breakdown of MP due to water shear forces induced by treatment facilities (e.g., pumping, mixing, and bubbling) could be the major causes for NP generation in the WWTP. Conventional wastewater treatment processes are ineffective for the complete removal of MPs. Although these processes are capable of removing ∼95% of MPs, they tend to accumulate in sludge. Thus, a significant number of MPs may still be released into the environment from WWTPs on a daily basis. Therefore, this study suggested that using DAF process in the primary treatment unit can be an effective strategy to control MP in the initial stage before it goes to the secondary and tertiary stage.

Residential houses - a major point source of microplastic pollution: insights on the various sources, their transport, transformation, and toxicity behaviour

Municipal wastewater has been considered as one of the largest contributors and carriers of microplastics to the aquatic environment. However, the various residential activities that generate municipal wastewater are equally significant whenever the source of microplastics in aquatic system is accounted. However, so far, only municipal wastewater has received wide attention in previous review articles. Hence, this review article is written to address this gap by highlighting, firstly, the chances of microplastics arising from the usage of personal care products (PCPs), laundry washing, face masks, and other potential sources. Thereafter, the various factors influencing the generation and intensity of indoor microplastic pollution and the evidence available on the possibility of microplastic inhalation by humans and pet animals are explained. Followed by that, the removal efficiency of microplastics observed in wastewater treatment plants, the fate of microplastics present in the effluent and biosolids, and their impact on aquatic and soil environment are explored. Furthermore, the impact of aging on the characteristics of microsized plastics has been explored. Finally, the influence of age and size of microplastics on the toxicity effects and the factors impacting the retention and accumulation of microplastics in aquatic species are reviewed. Furthermore, the prominent pathway of microplastics into the human body and the studies available on the toxicity effects observed in human cells upon exposure to microplastics of different characteristics are explored.

Microplastics in Sewage Sludge: A review

Microplastics (MPs) represent a serious problem for the environment and for this reason they have been studied in many articles, especially their presence in aquatic environments and soils. MPs have been found in wastewater and sewage sludge from municipal wastewater treatment plants (WWTPs). Most part of the published works have focused on the detection and elimination of MPs in the water line and several reviews have been published in the last years. In addition, the application of sewage sludge produced from WWTPs for agricultural use is known to be a primary source of MPs in soils. However, in the scientific literature less attention has been paid to the sludge and little is known about MPs fate when it is applied in agriculture. This work aims to give a global revision on the most used techniques to identify and detect MPs in sludges, their characteristics and incidence, their effect on sludge treatments and their impact on the environment. As far as we know, there are no standardized protocols for MPs extraction from soil and the possible repercussions on the cultivation of plants are not known. This review evidences that more studies are necessary to stablished standardized protocols and decipher the main mechanisms and the effects of MPs from sewage sludge in the environment.

A mixed method assessment of research productivity on microplastics in various compartments in the environment

Microplastic distribution and pollution as emerging contaminants have become a leading environmental issue globally, owing to their ecological and health implications on biota and humans. Although several bibliometric studies have been reported on microplastics, they are mostly restricted to selected environmental media. As a result, the present study aimed at assessing the literature growth trend of microplastics-related research and their distribution in the environment using a bibliometric approach. The Web of Science Core Collection was explored to retrieve published articles on microplastics from 2006 to 2021, and the data were analysed using the Biblioshiny package of RStudio. This study also highlighted filtration, separation, coagulation, membrane technology, flotation, bionanomaterials, bubble barrier devices, and sedimentation as MP remediation techniques. In the present study, a total of 1118 documents were collected from the literature search; the documents/author and authors/document were 0.308 and 3.25, respectively. A significant growth rate of 65.36% was recorded with notable progress between 2018 and 2021. China, the USA, Germany, the UK, and Italy recorded the highest number of publications within the period under consideration. A collaboration index of 3.32 was also relatively high, with the Netherlands, Malaysia, Iran, France, and Mexico having the highest MCP ratios, respectively. It is anticipated that findings from this study will help the policymakers in addressing issues concerning microplastic pollution assist the researchers in identifying areas to concentrate their studies, and where to seek collaboration in their future research plans.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13762-023-04916-7.

Microplastics in biosolids: A review of ecological implications and methods for identification, enumeration, and characterization

Biosolids, or treated sludge, are by-products of the wastewater treatment processes and are commonly used in agricultural applications to enrich soil nutrients. However, it contains microplastics, plastic particles with a diameter below 1 mm. Microplastics exist and accumulate in the environment, which can have major impacts on the ecosystem. Despite their abundance in the environment, there are to date no standardized methods for their enumeration and characterization. A literature review was conducted focusing on the occurrence of microplastics at wastewater treatment plants, particularly in the solid waste stream, and their influence on the soil ecosystem where biosolids is applied. We found a conflicting evidence to which extent microplastics negatively impact the ecosystem. Some reported either a direct negative impact of microplastics or because of microplastic interaction with other soil contaminants. Meanwhile, other studies showed no effect or at certain amount of microplastics on the ecosystem. We also found that microplastics size, shape, type, concentration, and exposure time play a critical role in their ecological impacts. However, currently, there is no unified approach for microplastics identification and characterization in solid waste resulting in a various and incomparable data. Therefore, utilizing standardized methods for microplastics analysis must be considered as the initial step to better understand the impact of microplastics onto the environment. We suggest a method's scaling comparison as a practical approach to select and develop techniques based on cost, time, data obtained, accuracy, and sensitivity criteria. Further research into the ecotoxicity of microplastics and continuous monitoring of biosolid applications are also necessary.

Unaccounted Microplastics in the Outlet of Wastewater Treatment Plants—Challenges and Opportunities

Since the 1950s, plastic production has skyrocketed. Various environmental and human activities are leading to the formation and accumulation of microplastics (MPs) in aquatic and terrestrial ecosystems, causing detrimental effects on water, soil, plants, and living creatures. Wastewater treatment plants (WWTPs) are one of the primary MP management centers meant to check their entry into the natural systems. However, there are considerable limitations in effectively capturing, detecting, and characterizing these MPs in the inlet and outlet of WWTPs leading to “unaccounted MPs” that are eventually discharged into our ecosystems. In order to assess the holistic picture of the MPs’ distribution in the ecosystems, prevent the release of these omitted MPs into the environment, and formulate regulatory policies, it is vital to develop protocols that can be standardized across the globe to accurately detect and account for MPs in different sample types. This review will cover the details of current WWTP adoption procedures for MP management. Specifically, the following aspects are discussed: (i) several processes involved in the workflow of estimating MPs in the outlet of WWTPs; (ii) key limitations or challenges in each process that would increase the uncertainty in accurately estimating MPs; (iii) favorable recommendations that would lead to the standardization of protocols in the workflow and facilitate more accurate analysis of MPs; (iv) research opportunities to tackle the problem of ‘missing MPs’; and (v) future research directions for the efficient management of MPs. Considering the burgeoning research interest in the area of MPs, this work would help early scientists in understanding the current status in the field of MP analysis in the outlet of WWTPs.

Microplastics as an underestimated emerging contaminant in solid organic waste and their biological products: Occurrence, fate and ecological risks

Microplastics (MPs), as an emerging pollutant, have been widely detected in aquatic, terrestrial, and atmospheric ecosystems. Recently, more researchers indicated that solid organic waste is also a crucial repository of MPs and has become a vital pollution source in ecosystems. Although the occurrence and fate of MPs in solid organic waste and the interaction between MPs and biological treatments have been explored, there still needs to be comprehensive summaries. Hence, this study reviewed the occurrence and characteristics of MPs in solid organic waste and organic fertilizers. Meanwhile, this study summarized the influence of MPs on biological treatments (composting and anaerobic digestion) and their degradation characteristics. MPs are abundant in solid organic waste (0-220 ×10³ particles/kg) and organic fertilizer (0-30 ×10³ particles/kg), PP and PE are the prominent MPs, and fibers and fragments are the main shapes. MPs can affect the carbon and nitrogen conversion during biological treatments and interfere with microbial communities. The MP's characteristics changed after biological treatments, which should further consider their potential ecological risks. This review points out the existing problems of MPs in organic waste recycling and provides directions for their treatment in the future.

Occurrence and fate of microplastics from wastewater treatment plants assessed by a fluorescence-based protocol

Traditional stereomicroscopy (SM) is limited for the identification of microplastics of less than 500 µm in wastewater treatment plants (WWTPs). Accordingly, novel methods for the accurate quantification of these microplastics are needed. In this study, we investigated the polymer type, morphology, size distribution, and abundance of microplastics in each unit of three selected WWTPs by SM and a fluorescence-based protocol (FR) combined with FTIR. Using the FR method, most microplastics detected in the three WWTPs were 50-200 µm in size. Polyethylene, polypropylene, and polyamide were the main polymer types, and the distributions of fibers, films, and debris were determined. Despite highly similar microplastic removal rates (78.6‒95.2% (SM) and 77.4‒94.2% (FR)) in the WWTPs by the two methods, the microplastic abundances obtained by FR (405‒6987 items/L) were approximately 2 orders of magnitude higher than the corresponding results by SM (1‒21 items/L). In addition, a considerable number of small-sized microplastics (< 500 µm) were detected in the effluents (405‒947 items/L) using FR. These results clearly reveal that microplastics in WWTPs have been seriously underestimated in most previous studies based on SM. Further research should focus on the environmental risks of small-sized microplastics from WWTPs.

Toward a Better Understanding of the Contribution of Wastewater Treatment Plants to Microplastic Pollution in Receiving Waterways

Microplastics (1 µm-5 mm), are ubiquitous in daily-use products and regularly end up in the wastewater. The main part of the wastewater is treated in wastewater treatment plants (WWTPs), which allow for at least partial removal of microplastics. The present study aimed to understand the contribution of domestic wastewater to microplastic pollution in Flanders (Belgium) via two main discharge routes of microplastics: (1) the effluent, and (2) removed fractions. Furthermore the effect of effluent discharge on the microplastic contamination in the waterway was studied in both surface water and sediment samples of upstream and downstream locations of the discharge from three WWTPs. On average, 12.64 ± 20.20 microplastic/L entered a WWTP (10 µm-5 mm). The effluent contained on average 0.41 ± 0.91 microplastic/L, resulting in an average removal efficiency of 97.46% ± 2.33%, which is comparable with various (non-)European countries. Removal efficiencies are both polymer- and size-specific, and data suggest that smaller particles are less efficiently removed from the wastewater, which also causes an increased input of smaller particles to the environment. The sludge is the most efficient treatment process to remove microplastics. Despite the high removal efficiencies, still 1.11 × 10⁷  ± 3.07 × 10⁷ microplastics end up in the nearby waterway daily. Nonetheless, based on the results gathered in the present study, this does not seem to impact the microplastic concentration in the waterway significantly. In summary, the present study offers a holistic approach in the research on the impact of wastewater on microplastic pollution in the ecosystem, integrating different discharge routes and measuring the impact on environmental microplastic pollution. Environ Toxicol Chem 2023;42:642-654. © 2022 SETAC.

Recent approaches and advanced wastewater treatment technologies for mitigating emerging microplastics contamination - A critical review

Microplastics have been identified as an emerging pollutant due to their irrefutable prevalence in air, soil, and particularly, the aquatic ecosystem. Wastewater treatment plants (WWTPs) are seen as the last line of defense which creates a barrier between microplastics and the environment. These microplastics are discharged in large quantities into aquatic bodies due to their insufficient containment during water treatment. As a result, WWTPs are regarded as point sources of microplastics release into the environment. Assessing the prevalence and behavior of microplastics in WWTPs is therefore critical for their control. The removal efficiency of microplastics was 65 %, 0.2-14 %, and 0.2-2 % after the successful primary, secondary and tertiary treatment phases in WWTPs. In this review, other than conventional treatment methods, advanced treatment methods have also been discussed. For the removal of microplastics in the size range 20-190 μm, advanced treatment methods like membrane bioreactors, rapid sand filtration, electrocoagulation and photocatalytic degradation was found to be effective and these methods helps in increasing the removal efficiency to >99 %. Bioremediation based approaches has found that sea grasses, lugworm and blue mussels has the ability to mitigate microplastics by acting as a natural trap to the microplastics pollutants and could act as candidate species for possible incorporation in WWTPs. Also, there is a need for controlling the use and unchecked release of microplastics into the environment through laws and regulations.

Microplastics in wastewater treatment plants: Sources, properties, removal efficiency, removal mechanisms, and interactions with pollutants

Since wastewater treatment plants (WWTPs) cannot completely remove microplastics (MPs) from wastewater, WWTPs are responsible for the release of millions of MPs into the environment even in 1 day. Therefore, knowing the sources, properties, removal efficiencies and removal mechanisms of MPs in WWTPs is of great importance for the management of MPs. In this paper, firstly the sources of MPs in WWTPs and the quantities and properties (polymer type, shape, size, and color) of MPs in influents, effluents, and sludges of WWTPs are presented. Following this, the MP removal efficiency of different treatment units (primary settling, flotation, biological treatment, secondary settling, filtration-based treatment technologies, and coagulation) in WWTPs is discussed. In the next section, details about MP removal mechanisms in critical treatment units (settling and flotation tanks, bioreactors, sand filters, membrane filters, and coagulation units) in WWTPs are given. In the last section, the mechanisms and factors that are effective in adsorbing organic-inorganic pollutants in wastewater to MPs are presented. Finally, the current situation and research gap in these areas are identified and suggestions are provided for topics that need further research in the future.

Current status of microplastics and nanoplastics removal methods: Summary, comparison and prospect

In modern society, plastics also play an indispensable role in people's lives due to their various excellent properties. However, when these plastic products are discarded after being used, after being subjected to external influences, they will continue to be worn, damaged and degraded into micro- and nano-scale plastics, which are microplastics and nanoplastics (M/NPs). Although people's attention has been paid to M/NPs at present, the focus is still mainly on the detection and hazard of M/NPs, and how to remove M/NPs is relatively less popular. This review was written in order to draw the attention of more researchers to remove M/NPs. This review first briefly introduces the research background of M/NPs, and also shows the main analytical methods currently used for qualitative and quantitative M/NPs. Then, most of the current literature on the removal of M/NPs was collected, and they were classified, summarized, and introduced according to the classification of physical, physicochemical, and biological methods. The advantages and disadvantages of various methods are summarized, and they are also compared, which can help more researchers choose the appropriate method for research. In addition, the application scenarios of these methods are briefly introduced. Finally, some future research directions are proposed for the current research status of M/NPs removal. It is hoped that this will further promote the development on the method of removing M/NPs.

Microplastics in sewage sludge: Distribution, toxicity, identification methods, and engineered technologies

Microplastic pollution is becoming a global challenge due to its long-term accumulation in the environment, causing adverse effects on human health and the ecosystem. Sludge discharged from wastewater treatment plants (WWTPs) plays a critical role as a carrier and primary source of environmental microplastic contamination. A significantly average microplastic variation between 1000 and 301,400 particles kg^-1 has been reported in the sludge samples. In recent years, advanced technologies have been successfully applied to address this issue, including adsorption, advanced oxidation processes (AOPs), and membrane bioreactors (MBRs). Adsorption technologies are essential to utilizing novel adsorbents (e.g., biochar, graphene, zeolites) for effectively removing MPs. Especially, the removal efficiency of polymer microspheres from an aqueous solution by Mg/Zn modified magnetic biochars (Mg/Zn-MBC) was obtained at more than 95%. Also, advanced oxidation processes (AOPs) are widely applied to degrade microplastic contaminants, in which photocatalytic by semiconductors (e.g., TiO₂ and ZnO) is a highly suitable approach to promote the degradation reactions owing to strongly hydroxyl radicals (OH*). Biological degradation-aided microorganisms (e.g., bacterial and fungal strains) have been reported to be suitable for removing microplastics. Yet, it was affected by biotic and abiotic factors of the environmental conditions (e.g., pH, light, temperature, moisture, bio-surfactants, microorganisms, enzymes) as well as their polymer characteristics, i.e., molecular weight, functional groups, and crystallinity. Notably, membrane bioreactors (MBRs) showed the highest efficiency in removing up to 99% microplastic particles and minimizing their contamination in sewage sludge. Further, MBRs illustrate the suitability for treating high-strength compounds, e.g., polymer debris and microplastic fibers from complex industrial wastewater. Finally, this study provided a comprehensive understanding of potential adverse risks, transportation pathways, and removal mechanisms of microplastic, which full-filled the knowledge gaps in this field.

The fate of microplastic in sludge management systems

Sewage sludge (SS) from wastewater treatment plants (WWTPs) is commonly used as a soil amendment on agricultural land; however, this sludge contains microplastics (MPs) which harm soil ecosystems and can leach into aquatic environments. This review aims to assess the fate of MPs in SS systems and, in the context of a changing agricultural scene, present alternatives for sustainable SS disposal that are consistent with the practices of a clean, circular economy. Anaerobic digestion and composting, which are commonly used to stabilize SS before land application, were not reported to substantially affect MP removal, although process efficiency and the microbiome were affected by MPs. Alternatively, MPs can be destroyed or removed by mono-incineration or combustion, but unfortunately, some MPs may remain in the ash after these processes. Therefore, the most desirable solutions would prevent MPs from entering the environment and remove them before they enter the biological part of a WWTP, where they build up in SS. Additionally, the management of MP-containing sludge must be adapted to the geographical context and the local economy, and it should begin with legislation addressing MPs in SS. The information presented here will help to develop good practices in waste management for preventing or decreasing the transfer of MPs into the environment.

A Review on the Role of Earthworms in Plastics Degradation: Issues and Challenges

Recently, the contribution of earthworms to plastic degradation and their capability to swallow smaller plastic fragments, known as microplastics, has been emphasized. The worm physically changes the size of microplastics and enhances microbial activities to increase the possibility of degradation. However, no research has shown that earthworms can chemically degrade microplastics to an element form, CO2 or H2O. In this review, previous research has been thoroughly explored to analyse the role that earthworms could play in plastic degradation in the soil. Earthworms can significantly affect the physical characteristics of plastics. However, earthworms’ abilities to chemically degrade or change the chemical structure of plastics and microplastics have not been observed. Additionally, earthworms exhibit selective feeding behaviour, avoiding areas containing a high plastics concentration and rejecting plastics. Consequently, earthworms’ abilities to adapt to the microplastics in soil in the environment can cause a problem. Based on this review, the challenges faced in earthworm application for plastic degradation are mostly expected to be associated with the toxicity and complexity of the plastic material and environmental factors, such as the moisture content of the soil and its temperature, microbial population, and feeding method.

Unraveling microplastics removal in wastewater treatment plant: A comparative study of two wastewater treatment plants in Thailand

Wastewater treatment plants (WWTPs) are considered as a problematic pathway for microplastics (MPs) entering the oceans. This study compares the efficiency of MP removal in two different WWTPs (A₁ and A₂) with a conventional treatment system located in Bangkok, Thailand. WWTP-A₂ is equipped with a pilot-scale ultrafiltration (UF) as a final polishing step. The number of MPs in the influent entering A₁ and A₂ was 16.55 ± 9.92 and 77.00 ± 7.21 MP/L, respectively. The average of 3.52 ± 1.43 and 10.67 ± 3.51 particles per L was found in the effluent discharged from A₁ and A₂, respectively, to nearby canals. The removal efficiency of WWTP-A₂ built as a closed underground system was shown to be up to 86.14% which is more efficient than the conventional WWTP (A₁). MPs were subsequently removed by a UF unit which resulted in a removal efficiency of 96.97%. However, when a large volume of treated wastewater volume is considered, a high concentration of MPs is discharged daily with the final effluent if the efficiency remains the same. The size fraction of 0.5-0.05 mm contributed to the largest proportion of MPs, and fibers were detected as the dominant group at both study sites. Results from a Fourier Transform Infrared Spectroscopy (FT-IR) confirmed that most fibers were polyethylene terephthalate (PET) derived from clothes. MPs retained in the sludge ranged from 2.63 × 10⁴ to 4.74 × 10⁴ particles per kilogram of dry sludge. A significant number of MPs can spread further to the environment by soil application. The results of the study indicate that the design of WWTPs and the addition of advanced tertiary treatment can improve MP removal efficiency of a WWTP. Moreover, the absence of a primary sedimentation tank in both treatment plants may influence the removal efficiency.

Characterization and removal of microplastics in a sewage treatment plant from urban Nagpur, India

Sewage treatment plant (STP) acts as a potential source of microplastic contamination in the environment. The presence of microplastics in the sewage treatment plant is reported over the globe in varying concentrations. Hence, the current study is intended to evaluate the presence and abundance of microplastics occurring in sewage treatment plants in India. The samples were processed through digestion and density separation, followed by microscopic and polymer identification through Fourier transform infrared spectroscopy. Also, different wastewater parameters were studied to analyze their influence. High microplastic concentrations were detected in the influent (1860 ± 265 MPs/L), which reduced by > 90%, to around 148 ± 51 MPs/L in the effluent. The concentration of microplastics in sewage sludge was 830 MPs/kg. The prominent plastic types identified include low-density polyethylene, polypropylene, polyurethane, polyvinyl chloride, and rayon. The smaller particles prevail in the effluent, releasing around 30 billion particles per day to the environment. This suggests that the current STP is efficient in removing the majority of the particles, but considerations are needed to avoid the ecological risks associated.

Microplastics separation using stainless steel mini-hydrocyclones fabricated with additive manufacturing

Microplastics have been widely detected in natural and engineered water systems and removing microplastics from various water matrices has become a major challenge. Mini-hydrocyclones (MHCs) have been previously applied to separate mediums of different phases. Given MHCs' capability of separating fine particles from liquid phase, three MHCs were designed and fabricated in stainless steel with 3D printing. Microplastics of densities that were both lower (<1 g·cm^-3) and higher (>1 g·cm^-3) than water's density were used to test the separation efficiency in ultra-purified water. The separation test was performed on single-stage MHC as well as MHCs in series in a closed hydraulic circuit. A range of important operational parameters, including split ratio, feed pressure, feed flow rate, and solid concentration, were evaluated to optimize the separation efficiency. The single-stage MHC experiment revealed that >80 % microplastics >20 μm can be effectively removed at the concentration tested, and the separation efficiency peaked at the split ratio of 35 %. MHCs in series demonstrated their ability to further enhance the separation efficiency of the ones with the same density, as well as separate microplastics of different densities. Mini-hydrocyclones' were also used to separate microplastics in synthetic stormwater, and separation efficiency reached 84 % and 98.1 % for low-density polyethylene (LDPE) and polyamide (PA). The results indicated the MHCs' potential for large-scale application in microplastic separation for industrial and municipal wastewater.

Occurrence, analysis of microplastics in sewage sludge and their fate during composting: A literature review

Microplastics (MP) are ubiquitous contaminants and their presence in sewage sludge has recently received attention as they may enter agro-ecosystems if sludge is used as organic soil amendment. Indeed, plastic particles (<5 mm) can be transported from wastewater and sewage sludge to the soil environment either directly within the plastic matrix or indirectly as adsorbed substances. In this paper, articles from 18 countries reporting the MP quantity and their characteristics in sewage sludge from wastewater treatment plants were reviewed and the MP concentration size and type were compared. The data show that MP abundance in sewage sludge ranged globally from 7.91 to 495 × 10³ particles kg^-1 with highest abundance of fiber shape and MP size of less than 500 μm. In this review, we summarized and discussed the methods most frequently used for extraction and characterization of MP in sewage sludge including organic matter removal, MP extraction; physical and morphological MP characterization and its chemical characterization for polymer identification. We also described the major factors potentially controlling the fate of MP during disposal strategies with particular focus on composting. We show that physical and microbiological factors are important for MP degradation during composting and suggest two remediation practices: (i) inoculation of the initial sludge with microbial plastic decomposers to remove MP from contaminated sewage sludge, and (ii) development of high temperature composting processes.

Implication of microplastic toxicity on functioning of microalgae in aquatic system

Microplastics (MPs) released from both primary and secondary sources affect the functioning of aquatic system. These MPs and components leached, can interact with aquatic organisms of all trophic levels, including the primary producers, such as microalgae. Considering the ecological value of microalgae and the toxicological effects of MPs towards them, this review provides: (1) a detailed understanding of the interactions between MPs and microalgae in the complex natural environment; (2) a discussion about the toxic effects of single type and mixtures of plastic particles on the microalgae cells, and (3) a discussion about the impacts of MPs on various features of microalgae -based bioremediation technology. For this purpose, toxic effects of MPs on various microalgal species were compiled and plastic components of MPs were ranked on the basis of their toxic effects. Based on available data, ranking for various plastic components was found to be: Polystyrene (PS) (rank 1) > Polyvinyl Chloride (PVC) > Polypropylene (PP) > Polyethylene (PE) (rank 4). Furthermore, the review suggested the need to understand joint toxicity of MPs along with co-contaminants on microalgae as the presence of other pollutants along with MPs might affect microalgae differently. In-depth investigations are required to check the impact of MPs on microalgae-based wastewater treatment technology and controlling factors.

A global review of microplastics in wastewater treatment plants: Understanding their occurrence, fate and impact

Microplastics (MPs) are emerging as a serious environmental concern, with wastewater treatment plants (WWTPs) acting as the main entry routes for MPs into aquatic and terrestrial ecosystems. On a global scale, our literature review found that MP research in WWTPs has only been conducted on 121 WWTPs in 17 countries, with the majority of the work being done in Europe (53%), followed by the United States of America and Canada (24%), Asia (18%), and Australia (5%) in recent years. MPs in WWTPs are primarily derived from Personal Care and Cosmetic Products (PCCPs), which are primarily composed of polyethylene (PE) derivatives. Based on the studies, microfibers (57%) and fragments (47%) are observed to be the most common MP forms in influents and effluents of WWTPs. The chemical characterization of MPs detected in WWTPs, showed the occurrence of polyethylene (PE) (22%), polystyrene (PS) (21%), and polypropylene (13%). Although MP retention/removal efficiencies of different treatment technologies vary from medium to high, deliberations on sludge disposal on agricultural soils containing MPs and MP intrusion into groundwater are required to sustainably regulate MP contaminant transport. Thus, the development of efficient detection methods and understanding their fate are of immense significance for the management of MPs. Despite the fact that ongoing research in MPs and WWTPs has unquestionably improved our understanding, many questions and concerns remain unanswered. In this review, the current status of the detection, occurrence, and impact of MPs in WWTPs across the world are systematically reviewed to prioritize policy-making to recognize the WWTPs as global conduits of MPs.

Wastewater treatment plants act as essential sources of microplastic formation in aquatic environments: A critical review

According to extensive in situ investigations, the microplastics (MPs) determined in current wastewater treatment plants (WWTPs) are mostly aged, with roughened surfaces and varied types of oxygen-containing functional groups (i.e., carbonyl and hydroxyl). However, the formation mechanism of aged MPs in WWTPs is still unclear. This paper systematically reviewed MP fragmentation and generation mechanisms in WWTPs at different treatment stages. The results highlight that MPs are prone to undergo physical abrasion, biofouling, and chemical oxidation-associated weathering in WWTPs at different treatment stages and can be further decomposed into smaller secondary MPs, including in nanoplastics (less than 1000 nm or 100 nm in size), suggesting that WWTPs can act as a formation source for MPs in aquatic environments. Sand associated mechanical crashes in the primary stage, microbes in active sewage sludge-related biodegradation in the secondary stage, and oxidant-relevant chemical oxidation processes (light photons, Cl₂, and O₃) in the tertiary stage are the dominant causes of MP formation in WWTPs. For MP formation mechanisms in WWTPs, external environmental forces (shear and stress forces, UV radiation, and biodegradation) can first induce plastic chain scission, destroy the plastic molecular arrangement, and create abundant pores and cracks on the MP surface. Then, the physicochemical properties (modulus of elasticity, tensile strength and elongation at break) of MPs shift consequently and finally breakdown into smaller secondary MPs or nanoscale plastics. Overall, this review provides new insights to better understand the formation mechanism, occurrence, fate, and adverse effects of aged microplastics/nanoplastics in current WWTPs.

The distribution and risk of microplastics discharged from sewage treatment plants in terrestrial and aquatic compartment

Many microplastics (MPs) were produced in daily life, which would enter sewage treatment plants (STPs) with the wastewater. Although the STPs has a good interception effect on these MPs, there will still be a part of MPs entering the environment with the effluent and sludge treatment, causing a certain ecological risk. This study investigated the abundance, characteristics and retention of MPs in different STPs, as well as the ecological risks caused by MPs entering the environment. The abundance of MPs in influent and effluent was ranged from 2.02 to 2.50 items L^-1 and 0.27-0.48 items L^-1, respectively. The abundance of MPs in dewatered sludge and sediment of Lake Dianchi was ranged from 3.719-6.949 × 10³ items (kg Ds)^-1 and 1.84-5.23 × 10³ items (kg Ds)^-1, respectively. So roughly 80% of the MPs were trapped and transferred into the dewatered sludge. The observed colors of MPs were transparent, black, blue, red, pale brown, green and gray, and their main species were polypropylene (PP) and polyethylene (PE). To further evaluate the ecological risks of MPs, the oyster mushroom was cultivated in a medium supplemented with MPs. It was found that MPs could be absorbed by oyster mushrooms with a 7-11% of absorption rate, the fibers were widely distributed in the stipes and the pileus. This study had theoretical significance for exploring the distribution of MPs in STPs and clarifying the ecological risk posed by MPs in the environment.

Estimation of kinetic constants in high-density polyethylene bead degradation using hydrolytic enzymes

Microplastic beads are an emerging contaminant that can cause serious environmental and public health problems. Potential bypass of microplastic beads from wastewater to sludge treatment systems is a key challenge in the conventional wastewater treatment process. Moreover, there are no systematic studies on microplastic bead degradation by hydrolytic enzymes that are rich in concentration within wastewater and sludge treatment processes (e.g., anaerobic digestion (AD)). In this study, lab-scale experiments were conducted to investigate the degradation of high-density polyethylene beads by hydrolytic enzymes (e.g., lipase) under various experimental conditions (e.g., temperature). In a 3-day batch experiment, protease was most effective in polyethylene bead degradation as 4.0% of the initial bead mass was removed at an enzyme concentration of 88 mg/L under thermophilic temperature (55 °C). It was also found that the increasing enzyme concentration and high temperature enhanced the polyethylene bead degradation. In a separate 7-day experiment with repeated doses of protease, 23.3% of the initial mass of beads was removed at thermophilic temperature, indicating that AD with a long retention time (e.g., 20 days) and heated temperature has a significant potential for polyethylene bead degradation. A mathematical model was developed and calibrated using the experimental results to estimate the kinetic constant of the high-density polyethylene bead reduction by an enzyme (k_1,i) and enzyme self-decay constant (k_2,ii). The calibrated k_1,i ranged from 5.0 to 8.1× 10^-4 L/mg/hr while k_2,ii was 0.44-1.10 L/mg/hr. Using the calibrated model, degradation of polyethylene beads using a mixture of cellulase and protease was simulated, considering an interactive-decay reaction between the two enzymes. The calibrated model was used to simulate the polyethylene bead degradation in AD where 70-95% of the initial bead mass was removed at typical retention time under mesophilic digestion (37.5 °C). Based on the experimental and simulation results, it can be concluded that hydrolytic enzymes can be an efficient technology for large-scale high-density polyethylene bead removal applications.

Does size matter? Quantification of plastics associated with size fractionated biosolids

This study investigated the occurrence and contribution of plastic particles associated with size fractionated biosolids to the total concentration in biosolids (treated sewage sludge) samples collected from 20 wastewater treatment plants (WWTP) across Australia. This was achieved through sequential size fractionation of biosolids samples to quantify the mass concentration of 7 common plastics across a range of biosolids size fractions, including below 25 μm which has not been assessed in many previous studies. Quantitative analysis was performed by pressurized liquid extraction followed by pyrolysis coupled to gas chromatography - mass spectrometry. Of the total quantified plastics (Σ₇plastics), the greatest proportion (27%) of the total mass were identified in the nominal <25 μm sized biosolids fraction. Polyethylene dominated the polymer mass in every size fraction, even though profiles varied between WWTPs. When comparing the sum of all sites for each sized biosolids fraction, the plurality of the polyethylene, polyvinyl-chloride, polystyrene, polypropylene, polycarbonate, and polyethylene-terephthalate concentrations were associated with the smallest size fraction (<25 μm). We confirm for the first time the presence of plastic particles in biosolids below a size fraction that is not captured by many methods. This is important, because of the potential greater significance of plastics in the low sizes to environmental and human health.

Long-Term Occurrence and Fate of Microplastics in WWTPs: A Case Study in Southwest Europe

Microplastic (MP) water pollution is a major problem that the world is currently facing, and wastewater treatment plants (WWTPs) represent one of the main alternatives to reduce the MP release to the environment. Several studies have analysed punctual samples taken throughout the wastewater treatment line. However, there are few long-term studies on the evolution of MPs over time in WWTPs. This work analyses the performance of a WWTP sited in Southwest Europe in relation with annual occurrence and fate of MPs. Samples were monthly taken at different points of the facility (influent, secondary effluent, final effluent, and sludge) and MPs were quantified and characterised by means of stereomicroscopy and FTIR spectrophotometry. The majority of MPs found in wastewater and sludge samples were fragments and fibres. Regarding to the chemical composition, in the water samples, polyethylene (PE), polyethylene terephthalate (PET) and polypropylene (PP) stood out, whereas, in the sludge samples, the main polymers were PET, polyamide (PA) and polystyrene (PS). The MPs more easily removed during the wastewater treatment processes were those with sizes greater than 500 µm. Results showed that the MPs removal was very high during all the period analysed with removal efficiencies between 89% and 95%, so no great variations were found between months. MP concentrations in dry sludge samples ranged between 12 and 39 MPs/g, which represented around 79% of the total MPs removed during the wastewater treatment processes. It is noticeable that a trend between temperature and MPs entrapped in sewage sludge was observed, i.e., higher temperatures entailed higher percentage of retention.

Systematic assessment of data quality and quality assurance/quality control (QA/QC) of current research on microplastics in biosolids and agricultural soils

Although a growing number of studies have reported microplastics (MPs) in biosolids and soils, there are significant differences in the concentrations found across different regions worldwide. This has raised questions about the quality of studies due to a lack of standardized sampling and analysis methods for detecting MPs in such complex samples. In this study, we applied a systematic quantitative literature review (SQLR) methodology to analyze studies reporting MPs in sludge/biosolids and agricultural soils. We also assessed the quality of individual studies on MPs in sludge/biosolids and soils based on the inclusion of quality assurance/quality control (QA/QC) procedures. There is limited understanding about MPs in soils with a history of biosolid application with only 9% of publications reporting MPs in biosolid-amended soil. There was almost eight orders of magnitude difference (3.4 × 10^-5 to 9.4 × 10³ particles/g) between the highest concentrations of MPs in sludge/biosolid samples compared to the lowest virgin soil samples. The literature shows a consistency in the polymer types (polyester, PP and PE) and morphotypes (fibres and fragments) of MPs most frequently detected in biosolids and soils, suggesting a potential role of biosolids in soils MP pollution. Despite the large variations in the sizes of MPs, there was a negative correlation between the lowest size detected and concentrations reported. This indicates that current concentrations of MPs are influenced by the detection size. Our assessment shows that the majority of studies to-date lack critical QA/QC measures, particularly field blank, positive control and method validation. This highlights an urgent need for quality improvement of future research in this field to produce reliable data, ultimately crucial to assess the risk of MPs and derive suitable environmental guidelines. It is recommended that MPs studies methodically include QA/QC protocols at every step of the process to ensure the integrity of the data that is published.

The life cycle of micro-nano plastics in domestic sewage

As a kind of novel pollutant, microplastics and nanoplastics have been commonly found in all regions of the world and have attracted widespread attention in recent years. Wastewater treatment plants are considered an important "source" and "sink" of micro-nano plastics pollution, so it is significant to study its transportation and fate in wastewater plants. This review summarizes the types and sources of micro-nano plastics in domestic wastewater and compares their removal efficiency and migration in different treatment processes in wastewater plants. The interlinkages and ecological risks among surface water, soil and atmospheric environments are also analyzed, providing a reference for future research on the impact of wastewater treatment plants on micro-nano plastics pollution.

Microplastics in Sewage Sludge: A Known but Underrated Pathway in Wastewater Treatment Plants

Interest in the presence of microplastics (MPs) in wastewater has grown significantly in recent years. In fact, wastewater treatment plants (WWTPs) represent the last barrier before the discharge of MPs into an aquatic ecosystem. The research has highlighted how MPs are in part effectively removed from the waters and accumulated inside the sewage sludge (SeS) produced by the WWTP, being a cause for concern, especially in the case of agricultural reuse. This work aims to analyze the existing literature on the (i) methodical procedure for MPs analysis (thermal, spectroscopic, optical analyses), (ii) qualitative and quantitative presence of MPs in SeS, (iii) effect on sludge properties, and (iv) the possible accumulation in amended soils. Based on the results already obtained in the literature, this work aims to provide critical insights to stimulate interest in the topic and direct future research on aspects that should be deepened. In particular, it emerges that there is a clear need for standardization of the collection methods and the analytical techniques for identifying and quantifying MPs, since their physico-chemical characterization and the study on aging and on the response towards acid or basic pre-treatments are fundamental for the understanding of microplastics ecotoxicological potential.

Evaluation of microplastics removal efficiency at a wastewater treatment plant discharging to the Sea of Marmara

Levels, composition and fate of microplastics (MPs) were investigated along different compartments of a secondary wastewater treatment plant (WWTP) with nutrient removal on the northern Sea of Marmara coast (Istanbul, Turkey). When all samples were combined, fibers were found to be the most dominant particles, followed by hard fragments. 500-1000 μm and 1000-2000 μm were the most common size ranges for wastewater and sludge, respectively. Rate of removal differed for sizes and shapes of the particles combined. Hard fragments of <500 μm and fibers of size ranges 250-500 μm and 1000-2000 μm were more successfully removed within the WWTP. Size averages increased throughout the WWTP units. 84.6-93.0% removal was achieved for grab and 3-hr composite samples. Despite the high removal rates of the WWTP, 2,934 × 10⁶ microplastic particles/d were released in the effluent to the Sea of Marmara. Our results show that the Ambarlı WWTP considerably contributes to microplastics contamination in the Sea of Marmara since the plant has a high operating capacity.

Circulation of fibrous microplastic (microfiber) in sewage and sewage sludge treatment processes

The fate of microplastics (MPs) in the sewage treatment process has been investigated worldwide, and novel results have been reported; few studies have also clarified the fate of MPs in the sewage sludge treatment process. Although most MPs in sewage are transferred to sludge, some flow back from the sludge treatment process to the sewage treatment process. Therefore, throughout the sewage treatment plant, the removal rate of MPs may increase via a countermeasure during the sludge treatment process. In this study, samples obtained from sewage and sewage sludge treatments were used to degrade organic matter with hydrogen peroxide. Water sample particles were trapped on Ni filters with 20-μm-sized pores, dried at room temperature and then the MPs were detected and identified by FTIR microscopy. Note that sludge samples were treated with hydrogen peroxide and separated by specific gravity using NaI solution. The concentration of MPs per unit volume was then calculated and the MPs load was estimated using flow rates of water and sludge. Subsequently, we clarified the fate of MPs with sizes of 20 μm or greater in a sewage treatment plant. When the MPs load in the influent sewage is 100%, 12% of the MPs were found to return to the sewage treatment process via the sidestream of the sludge treatment process. Per this observation, it was made evident that MPs are in fact circulating throughout the sewage and sludge treatment processes. MPs in the sidestream mainly consisted of the effluent from the sludge concentration process, and most MPs were thought to be fibrous polyethylene terephthalate (fibrous MPs, i.e. microfibers [MFs]). The results show that MFs circulate throughout the sewage and sludge treatment processes, and for effectively increasing the removal rate of MPs, the removal of MFs proves correspondingly effective during the sludge treatment process.

Microplastics in Wastewater and Drinking Water Treatment Plants: Occurrence and Removal of Microfibres

Microplastics (MPs), and specifically microfibres (MPFs), are ubiquitous in water bodies, including wastewater and drinking water. In this work, a thorough literature review on the occurrence and removal of MPs, and specifically MPFs in WWTPs and DWTPs, has been carried out. When the water is treated, an average microfiber removal efficiency over 70% is achieved in WWTPs and DWTPs. These high percentages are still inefficient for avoiding the presence of a large number of microfibres in treated wastewater and also in tap water. RSF, DAF, oxidation ditch and CAS processes have been described as the most efficient treatments for eliminating MPFs from wastewater treatment. It is remarkable the wide range of the data reported on this topic; for example, treated wastewater contains between not detected and 347 MPFs/L, whereas tap water contains between not detected and 168 MPFs/L. Microfibres constitute more than half of the MPs found in treated wastewater and sewage sludge, whereas in DWTP effluents the percentage of MPFs is around 32%. Nevertheless, the relative amount of MPFs reported in tap water is notably higher (71%). Microfibres from WWTPs are discharged to the environment, being a source of MP pollution. Additionally, MPs released by DWTPs directly enter the drinking water lines, which constitute a direct route for MP human consumption, so that it has been estimated that an adult may ingest an average value of 7500 MPFs per year only via tap water. Thus, this review provides an update on the performance of WWTPs and DWTPs in removing MPs from water, which is an issue of great interest.

Particulate plastics-plant interaction in soil and its implications: A review

Particulate plastics (<5 mm), including macroplastics (1 μm to 5 mm), microplastics (100 nm to 1 μm) and nanoplastics (<100 nm), have become a global environmental problem due to their widespread occurrence, distribution and ecosystem risk. Although numerous studies on particulate plastics have been conducted in aquatic systems, investigations in the soil ecosystem are lacking. Soil is the main storage place of particulate plastics, conferring significant impacts on plant growth and development. The impact of particulate plastics on plants is directly related to the safety of agricultural products. This review comprehensively examines the pollution characteristics and exposure pathways of particulate plastics in agricultural soils, highlighting plastic uptake process, and mechanisms in plants, and effects of particulate plastics, biodegradable particulate plastics and combined pollution of plastics with other environmental pollutants on plant performances. This review identifies a number of future research prospects including the development of accurate quantitative methods for plastic analysis in soil and plant samples, understanding the environmental behaviors of conventional and biodegradable particulate plastics in the presence and absence of other environmental pollutants, unravelling the fate of particulate plastics in plants, phyto-toxicity and molecular regulatory mechanisms of particultate plastics, and developing best management practices for the production of safe agricultural products in plastic-contaminated soils.