Indirect electrochemical treatment of bisphenol A in water via electrochemically generated Fenton's reagent

Chlorination of Emerging Contaminants for Application in Potable Wastewater Reuse: Disinfection Byproduct Formation, Estrogen Activity, and Cytotoxicity

With increasing water scarcity, many utilities are considering the potable reuse of wastewater as a source of drinking water. However, not all chemicals are removed in conventional wastewater treatment, and disinfection byproducts (DBPs) can form from these contaminants when disinfectants are applied during or after reuse treatment, especially if applied upstream of advanced treatment processes to control biofouling. We investigated the chlorination of seven priority emerging contaminants (17β-estradiol, estrone, 17α-ethinylestradiol, bisphenol A (BPA), diclofenac, p-nonylphenol, and triclosan) in ultrapure water, and we also investigated the impact of chlorination on real samples from different treatment stages of an advanced reuse plant to evaluate the role of chlorination on the associated cytotoxicity and estrogenicity. Many DBPs were tentatively identified via liquid chromatography (LC)- and gas chromatography (GC)-high resolution mass spectrometry, including 28 not previously reported. These encompassed chlorinated, brominated, and oxidized analogs of the parent compounds as well as smaller halogenated molecules. Chlorinated BPA was the least cytotoxic of the DBPs formed but was highly estrogenic, whereas chlorinated hormones were highly cytotoxic. Estrogenicity decreased by ∼4-6 orders of magnitude for 17β-estradiol and estrone following chlorination but increased 2 orders of magnitude for diclofenac. Estrogenicity of chlorinated BPA and p-nonylphenol were ∼50% of the natural/synthetic hormones. Potential seasonal differences in estrogen activity of unreacted vs reacted advanced wastewater treatment field samples were observed.

New Barrier Role of Iron Plaque: Producing Interfacial Hydroxyl Radicals to Degrade Rhizosphere Pollutants

Iron plaque, as a natural barrier between rice and soil, can reduce the accumulation of pollutants in rice by adsorption, contributing to the safe production of rice in contaminated soil. In this study, we unveiled a new role of iron plaque, i.e., producing hydroxyl radicals (·OH) by activating root-secreted oxygen to degrade pollutants. The ·OH was produced on the iron plaque surface and then diffused to the interfacial layer between the surface and the rhizosphere environment. The iron plaque activated oxygen via a successive three-electron transfer to produce ·OH, involving superoxide and hydrogen peroxide as the intermediates. The structural Fe(II) in iron plaque played a dominant role in activating oxygen rather than the adsorbed Fe(II), since the structural Fe(II) was thermodynamically more favorable for oxygen activation. The oxygen vacancies accompanied by the structural Fe(II) played an important role in oxygen activation to produce ·OH. The interfacial ·OH selectively degraded rhizosphere pollutants that could be adsorbed onto the iron plaque and was less affected by the rhizosphere environments than the free ·OH. This study uncovered the oxidative role of iron plaque mediated by its produced ·OH, reshaping our understanding of the role of iron plaque as a barrier for rice.

Application of iron-intercalated graphite for modification of nickel foam cathode in heterogeneous electro-Fenton system: Bisphenol A removal from water at neutral pH

The presence of bisphenol A (BPA) in natural waters can be highly harmful due to its high persistence and adverse effects, raising concerns to remove this hazardous compound. Herein, an electro-Fenton system is proposed to eliminate BPA, wherein the iron source in the Fenton reaction is provided by its intercalation into the carbon layers of graphite. The produced heterogeneous catalyst was then coated onto the nickel foam serving as a cathode. The magnetic graphite intercalated compound (mGIC) and the modified cathode (before and after experiments) were characterized by FE-SEM, EDX, XPS, and XRD analyses. Some effective parameters, namely pH (3-9), current density (0-20 mA cm-2), and BPA concentration (0.5-20 mg L-1) were studied. At pH 3, the removal of BPA was 95.52%, and under neutral circumstances, the BPA and TOC removals were 85.70 and 58.12%, respectively at the initial BPA concentration of 10 mg L-1. The proposed system was also applied to several water sources spiked with BPA at the concentration of 5 mg L-1 under neutral pH, which exhibited considerable removal of 99.74%, 99.72%, and 92.70% for groundwater, municipal effluent wastewater, and tap water, respectively. The proposed system was applied for 15 consecutive cycles without showing significant changes in BPA removal, indicating its excellent stability and reusability. Furthermore, based on the analysis of intermediates, a possible decomposition pathway was proposed, indicating a reduction in overall toxicity. By using the proposed heterogeneous electro-Fenton system, iron waste is avoided, and operational costs of treatment can be reduced due to the absence of iron sludge production and catalyst loss.

Improved visible-light-driven photocatalytic removal of Bisphenol A using V2O5/WO3 decorated over Zeolite: Degradation mechanism and toxicity

WO₃/Zeolite/V₂O₅ (TZV) composite synthesized through co-precipitation was used for the degradation of Bisphenol-A (BpA). XRD and Raman spectra were employed to ascertain the crystallinity of the composite. The pristine nature of the compound without any free particles over the zeolite surface was established through FESEM, thus, substantiating the composite character of the material. The enhancement in activity after doping with WO₃ was ascertained by DRS-UV. Photocatalytic degradation studies clearly established the superiority of TZV 10 over bare V₂O₅. Complete BpA degradation (100%) was attained at 50 min of incubation with 0.75 g/L TZV-10 in acidic medium (pH 3) for an initial BpA concentration of 100 mg/L. HPLC-MS/MS analysis was used to decipher the degradation pathway. The catalyst was stable even after 9 cycles. Phytotoxicity studies and lake water treatment results proved the environmental efficiency of the synthesized material.

Coupled Sorption and Oxidation of Soil Dissolved Organic Matter on Manganese Oxides: Nano/Sub-nanoscale Distribution and Molecular Transformation

In soil environments, the sequestration and transformation of organic carbon are closely associated with soil minerals. Birnessite (MnO₂) is known to strongly interact with soil dissolved organic matter (DOM), but the microscopic distribution and molecular transformation of soil DOM on birnessite are still poorly understood. In this study, the coupled sorption and oxidation of soil DOM on birnessite were investigated at both the microscopic scale and the molecular level. Spherical aberration corrected scanning transmission electron microscopy (Cs-STEM) results revealed, at the nano- to sub-nanoscale, that DOM was located both on the surfaces and within the interflakes or pore spaces of birnessite, and DOM within the interflakes displayed a higher oxidation state than that on the surfaces. Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS) results suggested that a portion of phenolic compounds were preferentially sorbed and oxidized, resulting in the formation of compounds with higher oxygen contents and polymeric products. Our Cs-STEM and FT-ICR-MS results highlighted the significance of organo-mineral associations in the microscopic mineral structure for the reactivity of organic carbon and provided the molecular evidence for the transformation of soil DOM by birnessite, which contributed to the understanding of the dynamics of soil dissolved organic carbon.

Heterogeneous electro-Fenton process for degradation of bisphenol A using a new graphene/cobalt ferrite hybrid catalyst

A simple, efficient, environmentally friendly, and inexpensive synthesis route was developed to obtain a magnetic nano-hybrid (GH) based on graphene and cobalt ferrite. Water with a high content of natural organic matter (NOM) was used as solvent and a source of carbon. The presence of NOM in the composition of GH was confirmed by FTIR and Raman spectroscopy, which evidenced the formation of graphene, as also corroborated by XRD analyses. The diffractograms and TEM images showed the formation of a hybrid nanomaterial composed of graphene and cobalt ferrite, with crystallite and particle sizes of 0.83 and 4.0 nm, respectively. The heterogeneous electro-Fenton process (EF-GH) achieved 100% degradation of bisphenol A (BPA) in 50 min, with 80% mineralization in 7 h, at pH 7, using a current density of 33.3 mA cm^-2. The high catalytic performance was achieved at neutral pH, enabling substantial reduction of the costs of treatment processes. This work contributes to understanding the role of NOM in the synthesis of a magnetic nano-hybrid based on graphene and cobalt ferrite, for use in heterogeneous catalysis. This nano-hybrid has excellent potential for application in the degradation of persistent organic pollutants found in aquatic environments.

Degradation of glyphosate herbicide by an electro-Fenton process using carbon felt cathode

An electro-Fenton system, which consists of a Pt gauze anode and a commercial carbon felt cathode, is commonly employed to generate in situ hydrogen peroxide, hydroxyl radical and regenerate ferrous catalyst for glyphosate degradation (a widely used herbicide in Vietnam) in aqueous solution. The absorbance measurements used to determine the glyphosate concentration during the electrolysis proved that glyphosate was degraded by pseudo-first-order kinetic. The influence of pH, current density, catalyst concentration and initial content of the glyphosate on mineralisation efficiency were studied by monitoring the total organic carbon (TOC) and hydrogen peroxide concentration during electrolysis. The results show that the maximal removal percentage of glyphosate was 91.91% with applied current density of 10 mA cm-2, pH 3, 0.1 mM Fe2+, 0.05 M Na2SO4, and 0.1 mM glyphosate in 40 min. The degrading rate constant of glyphosate degradation was calculated to be kapp = 0.063 min-1. In this 91.91% removal, 81.65% of glyphosate was mineralised and the remainder consists of intermediates produced during the electro-Fenton process.

Removal of bisphenol A from acidic sulfate medium and urban wastewater using persulfate activated with electroregenerated Fe2

Model solutions of bisphenol A (BPA) in 0.050 M Na₂SO₄ at pH 3.0 have been treated by the electro/Fe²⁺/persulfate process. The activation of 5.0 mM persulfate with 0.20 mM Fe²⁺ yielded a mixture of sulfate radical anion (SO₄^-) and OH, although quenching tests revealed the prevalence of the former species as the main oxidizing agent. In trials run in an IrO₂/carbon-felt cell, 98.4% degradation was achieved alongside 61.8% mineralization. The energy consumption was 253.9 kWh (kg TOC)^-1, becoming more cost-effective as compared to cells with boron-doped diamond and Pt anodes. Carbon felt outperformed stainless steel as cathode because of the faster Fe²⁺ regeneration. All BPA concentration decays agreed with a pseudo-fist-order kinetics. The effect of persulfate, Fe²⁺ and BPA concentrations as well as of the applied current on the degradation process was assessed. Two dehydroxylated and three hydroxylated monobenzenic by-products appeared upon SO₄^- and OH attack, respectively. The analogous treatment of BPA spiked into urban wastewater yielded a faster degradation and mineralization due to the co-generation of HClO and the larger OH production as SO₄^- reacted with Cl^-.

Insights into the interactions of bisphenol and phthalate compounds with unamended and carnitine-amended montmorillonite clays

Montmorillonite clays could be promising sorbents to mitigate toxic compound exposures. Bisphenols A (BPA) and S (BPS) as well as phthalates, dibutyl phthalate (DBP) and di-2-ethylhexyl phthalate (DEHP), are ubiquitous environmental contaminants linked to adverse health effects. Here, we combined computational and experimental methods to investigate the ability of montmorillonite clays to sorb these compounds. Molecular dynamics simulations predicted that parent, unamended, clay has higher binding propensity for BPA and BPS than for DBP and DEHP; carnitine-amended clay improved BPA and BPS binding, through carnitine simultaneously anchoring to the clay through its quaternary ammonium cation and forming hydrogen bonds with BPA and BPS. Experimental isothermal analysis confirmed that carnitine-amended clay has enhanced BPA binding capacity, affinity and enthalpy. Our studies demonstrate how computational and experimental methods, combined, can characterize clay binding and sorption of toxic compounds, paving the way for future investigation of clays to reduce BPA and BPS exposure.

Unravelling lewis acidic and reductive characters of normal and inverse nickel-cobalt thiospinels in directing catalytic H2O2 cleavage

(Inverse) spinel-typed bimetallic sulfides are fascinating H₂O₂ scissors because of the inclusion of S^2-, which can regenerate metals (M^δ+, δ ≤ 2) used to produce ^•OH via H₂O₂ dissection. These sulfides, however, were under-explored regarding compositional, structural, and electronic tunabilities based on the proper selection of metal constituents. Motivated by S-modified Ni^δ+/Co^δ+ promising to H₂O₂ cleavage, Ni₂CoS₄, NiCo₂S₄, NiS/CoS were synthesized and contrasted with regards to their catalytic traits. Ni₂CoS₄ provided the greatest activity in dissecting H₂O₂ among the catalysts. Nonetheless, Ni₂CoS₄ catalyzed H₂O₂ scission primarily via homogeneous catalysis mediated by leached Ni^δ+/Co^δ+. Conversely, NiCo₂S₄, NiS, and CoS catalyzed H₂O₂ cleavage mainly via unleached Ni^δ+/Co^δ+-enabled heterogeneous catalysis. Of significance, NiCo₂S₄ provided Lewis acidic strength favorable to adsorb H₂O₂ and desorb ^•OH compared to NiS and CoS, respectively. Of additional significance, NiCo₂S₄ provided S^2- with lesser energy required to reduce M^(δ+1)+ via e- transfer than NiS/CoS. Hence, NiCo₂S₄ prompted H₂O₂ scission cycle per unit time better than NiS/CoS, as evidenced by kinetic assessments. NiCo₂S₄ was also superior to Ni₂CoS₄ because of the elongated lifespan anticipated as ^•OH producer, resulting from heterogeneous catalysis with moderate Ni^δ+/Co^δ+ leaching. Furthermore, NiCo₂S₄ revealed the greatest recyclability and mineralization efficiency in decomposing recalcitrants via ^•OH-mediated oxidation.

Effect of the CuO addition on a Sb-doped SnO2 ceramic electrode applied to the removal of Norfloxacin in chloride media by electro-oxidation

Norfloxacin is employed as in veterinary and human medicine against gram-positive and gram-negative bacteria. Due to the ineffective treatment at the wastewater treatment plants it becomes an emergent pollutant. Electro-oxidation appears as an alternative to its effective mineralization. This work compares Norfloxacin electro-oxidation on different anodic materials: two ceramic electrodes (both based on SnO₂ + Sb₂O₃ with and without CuO, named as CuO and BCE, respectively) and a boron doped diamond (BDD). First, the anodes were characterized by cyclic voltammetry, revealing that NOR direct oxidation occurred at 1.30 V vs. Ag/AgCl. The higher the scan rate the higher both the current density and the anodic potential of the peak. This behavior was analyzed using the Randles-Sevcik equation to calculate the Norfloxacin diffusion coefficient in aqueous media, giving a value of D = 7.80 × 10^-6 cm² s^-1 at 25 °C), which is close to the predicted value obtained using the Wilke-Chang correlation. The electrolysis experiments showed that both NOR and TOC decay increased with the applied current density, presenting a pseudo-first order kinetic. All the anodes tested achieved more than 90% NOR degradation at each current density. The CuO is not a good alternative to BCE because although it acts as a catalyst during the first use, it is lost from the anode surface in the subsequent uses. According to their oxidizing power, the anodes employed are ordered as follows: BDD > BCE > CuO.

Degradation of pesticide Cartap in Padan 95SP by combined advanced oxidation and electro-Fenton process

The electro-Fenton process combined with a boron-doped diamond-positive electrode in a one-compartment cell has shown efficient degradation of Cartap (95% in Padan 95SP) by hydroxyl radicals (•OH) generated in the electro-Fenton and the electrochemical oxidation processes. The influence of added NaOCl in a pretreatment step, effects of H2O2 concentration, Fe2+-ion addition, presence of further metals acting as co-catalysts, and solution pH on the efficiency of Cartap degradation were studied. The concentration of Cartap was determined by UV-vis spectroscopy according to the 5,5-dithiobis-(2-nitrobenzoic acid) procedure. The efficiency reaches approximately 80% when measured as total carbon concentration decrease, even with increased concentrations of H2O2, Fe2+, or metal ions added as co-catalyst. This limitation is presumably due to recalcitrant intermediates, which cannot be destroyed by •OH.

Theoretical Description of Carbon Felt Electrical Properties Affected by Compression

Electro-conductive carbon felt (CF) material is composed by bonding together different lengths of carbon filaments resulting in a porous structure with a significant internal surface that facilitates enhanced electrochemical reactions. Owing to its excellent electrical properties, CF is found in numerous electrochemical applications, such as electrodes in redox flow batteries, fuel cells, and electrochemical desalination apparatus. CF electro-conductivity mostly arises from the close contact between the surface of two electrodes and the long carbon fibers located between them. Electrical conductivity can be improved by a moderate pressing of the CF between conducting electrodes. There exist large amounts of experimental data regarding CF electro-conductivity. However, there is a lack of analytical theoretical models explaining the CF electrical characteristics and the effects of compression. Moreover, CF electrodes in electrochemical cells are immersed in different electrolytes that affect the interconnections of fibers and their contacts with electrodes, which in turn influence conductivity. In this paper, we investigated both the role of CF compression, as well as the impact of electrolyte characteristics on electro-conductivity. The article presents results of measurements, mathematical analysis of CF electrical properties, and a theoretical analytical explanation of the CF electrical conductivity which was done by a stochastic description of carbon filaments disposition inside a CF frame.

Crossflow electrochemical filtration for elimination of ibuprofen and bisphenol a from pure and competing electrolytic solution conditions

For the first time, a crossflow electrochemical filtration system containing multiwalled carbon nanotubes (MWNTs) blended with buckypaper as a flat sheet dual membrane electrode was investigated for the removal of two contaminants of emerging concern, Ibuprofen and Bisphenol A. Breakthrough experiments revealed that a crossflow configuration could be highly efficient in eliminating both contaminants at applied DC potentials of 2 and 3 V over an extended period, from pure salt electrolyte as well as from synthetic secondary wastewater effluent. The shear flow provided consistent surface coverage resulting in excellent sorption performance. The long residence time of the two contaminants within the membrane (18.3 s) was sufficient enough to allow for almost complete degradation of phenolic aromatic products and quinoid rings and the resulting formation of aliphatic carboxylic acids, which was more evident at a higher applied potential (3 V). The formation of the non-toxic aliphatic carboxylic acids is a clear indication of the superior electrochemical performance of the crossflow mode over the dead-end flow-through system. Moreover, this study provides an in-depth understanding of different factors such as filter surface area and residence time that can greatly affect the removal of the contaminants considered.

Effects of HCO3- on Degradation of Toxic Contaminants of Emerging Concern by UV/NO3. ENVIRONMENTAL SCIENCE & TECHNOLOGY 2018;52:12697-12707. [PMID: 30284820 DOI: 10.1021/acs.est.8b04383]

This study investigated the significant influence of HCO₃^- on the degradation of contaminants of emerging concern (CECs) during nitrate photolysis at 254 nm for water reuse applications. The second-order rate constants for the reactions between selected contaminants with carbonate radical (CO₃^•-) were determined at pH 8.8 and T = 20 °C: estrone ((5.3 ± 1.1) × 10⁸ M^-1 s^-1), bisphenol A ((2.8 ± 0.2) × 10⁸ M^-1 s^-1), 17α-ethynylestradiol ((1.6 ± 0.3) × 10⁸ M^-1 s^-1), triclosan ((4.2 ± 1.4) × 10⁷ M^-1 s^-1), diclofenac ((2.7 ± 0.7) × 10⁷ M^-1 s^-1), atrazine ((5.7 ± 0.1) × 10⁶ M^-1 s^-1), carbamazepine ((4.2 ± 0.01) × 10⁶ M^-1 s^-1), and ibuprofen ((1.2 ± 1.1) × 10⁶ M^-1 s^-1). Contributions from UV, reactive nitrogen species (RNS), hydroxyl radical (^•OH), and CO₃^•- to the CEC decomposition in UV/NO₃^- in the presence and absence of HCO₃^- were investigated. In addition, possible transformation products and degradation pathways of triclosan, diclofenac, bisphenol A, and estrone in UV/NO₃^-/HCO₃^- were proposed based on the mass (MS) and MS² spectra. Significant reduction in the cytotoxicity of bisphenol A was observed after the treatment with UV/NO₃^-/HCO₃^-.

Graphene-doped carbon black gas diffusion electrode for nonmetallic electrochemical advanced oxidation process under mild conditions

Graphene-doped (<3 wt%) carbon black gas diffusion electrodes (GDEs) were prepared as the cathode for nonmetallic electrochemical advanced oxidation process (EAOP) in the neutral environment. The elemental composition, porous structure and active surface area were characterized and the concentration of Hydrogen peroxide (H₂O₂) and OH• were determined. Bisphenol A (BPA) was used as a model pollutant to assess the performance of the EAOP for organic wastewater treatment. The results showed that oxygen in the atmosphere was reduced to OH• on the GDE, where carbon black catalyzed oxygen reduction to H₂O₂ and graphene provide Π-electrons for the following H₂O₂ decomposition. BPA with initial concentration of 20 mg L^-1 was completely removed within 30 min and the total organic carbon removal reached 44.60%. The EAOP with the graphene-doped carbon black GDEs exhibited significant advantages for organic wastewater treatment.

Electric and Hydraulic Properties of Carbon Felt Immersed in Different Dielectric Liquids

Electroconductive carbon felt (CF) material, having a permeable structure and significant electroconductive surface, is widely used for electrodes in numerous electrochemical applications such as redox flow batteries, fuel cells, electrochemical desalination apparatus, etc. The internal structure of CF is composed of different lengths of carbon filaments bonded together. This structure creates a large number of stochastically oriented and stochastically linked channels that have different lengths and cross sections. Therefore, the CF hydraulic permeability is similar to that of porous media and is determined by the internal empty volume and arrangement of carbon fibers. Its electroconductivity is ensured by the conductivity of the carbon filaments and by the electrical interconnections between fibers. Both of these properties (permeability and electrical conductivity) are extremely important for the efficient functioning of electrochemical devices. However, their influences counter each other during CF compressing. Increasing the stress on a felt element provides supplementary electrical contacts of carbon filaments, which lead to improved electrical conductivity. Thus, the active surface of the felt electrode is increased, which also boosts redox chemical reactions. On the other hand, compressed felt possesses reduced hydrodynamic permeability as a result of a diminished free volume of porous media and intrinsic channels. This causes increasing hydrodynamic expenditures of electrolyte pumping through electrodes and lessened cell (battery) efficiency. The designer of specific electrochemical systems has to take into account both of these properties when selecting the optimal construction for a cell. This article presents the results of measurements and novel approximating expressions of electrical and hydraulic characteristics of a CF during its compression. Since electrical conductivity plays a determining role in providing electrochemical reactions, it was measured in dry conditions and when the CF was immersed in several non-conductive liquids. The choice of such liquids prevented side effects of electrolyte ionic conductivity impact on electrical resistivity of the CF. This gave an opportunity to determine the influences of dielectric parameters of electrolytes to increase or decrease the density of interconnectivity of carbon fibers either between themselves or between them and electrodes. The experiments showed the influence of liquid permittivity on the conductivity of CF, probably by changing the density of fiber interconnections inside the felt.

Application of electrochemical advanced oxidation to bisphenol A degradation in water. Effect of sulfate and chloride ions

Electrochemical oxidation with electrogenerated H₂O₂ (EO- H₂O₂), electro-Fenton (EF), photoelectro-Fenton (PEF) and solar PEF (SPEF) have been applied to mineralize bisphenol A solutions in 0.050 M Na₂SO₄ or 0.008 M NaCl + 0.047 M Na₂SO₄ at pH 3.0. The assays were performed in an undivided cell with a boron-doped diamond (BDD) anode and an air-diffusion cathode for continuous H₂O₂ production. The PEF and SPEF processes yielded almost total mineralization due to the potent synergistic action of generated hydroxyl radicals and active chlorine, in conjunction with the photolytic action of UV radiation. The higher intensity of UV rays from sunlight explained the superior oxidation ability of SPEF. The effect of applied current density was studied in all treatments, whereas the role of bisphenol A concentration was examined in PEF. Bisphenol A abatement followed a pseudo-first-order kinetics, which was very quick in SPEF since UV light favored a large production of hydroxyl radicals from Fenton's reaction. Eight non-chlorinated and six chlorinated aromatics were identified as primary products in the chloride matrix. Ketomalonic, tartronic, maleic and oxalic acids were detected as final short-chain aliphatic carboxylic acids. The large stability of Fe(III)-oxalate complexes in EF compared to their fast photomineralization in PEF and PEF accounted for by the superior oxidation power of the latter processes.

Degradation of Bisphenol A by Peroxymonosulfate Catalytically Activated with Mn1.8Fe1.2O4 Nanospheres: Synergism between Mn and Fe

A high-efficient, low-cost, and eco-friendly catalyst is highly desired to activate peroxides for environmental remediation. Due to the potential synergistic effect between bimetallic oxides' two different metal cations, these oxides exhibit superior performance in the catalytic activation of peroxymonosulfate (PMS). In this work, novel Mn_1.8Fe_1.2O₄ nanospheres were synthesized and used to activate PMS for the degradation of bisphenol A (BPA), a typical refractory pollutant. The catalytic performance of the Mn_1.8Fe_1.2O₄ nanospheres was substantially greater than that of the Mn/Fe monometallic oxides and remained efficient in a wide pH range from 4 to 10. More importantly, a synergistic effect between solid-state Mn and Fe was identified in control experiments with Mn₃O₄ and Fe₃O₄. Mn was inferred to be the primary active site in the surface of the Mn_1.8Fe_1.2O₄ nanospheres, while Fe(III) was found to play a key role in the synergism with Mn by acting as the main adsorption site for the reaction substrates. Both sulfate and hydroxyl radicals were generated in the PMS activation process. The intermediates of BPA degradation were identified and the degradation pathways were proposed. This work is expected to help to elucidate the rational design and efficient synthesis of bimetallic materials for PMS activation.

Removal of bisphenol A by electrochemical carbon-nanotube filter: Influential factors and degradation pathway

Bisphenol A is a chemical with hazardous health effects that is largely used in the manufacture of extensively used products including adhesives, plastics, powder paints, thermal paper and paper coatings, and epoxy resin, and is reported to exist in nature in an accumulative manner. In this study, both pristine and boron-doped multiwalled carbon nanotubes (MWNTs) were employed as filtration and electrochemical filtration materials, resulting in a significant removal of bisphenol A with identical performance for both MWNTs types. It was shown that the presence of salt is not critical for the greatest contaminant removal efficiency, likely due to the vital role of other electroactive species (e.g. reactive oxygen species). Near complete removal of 1 mg L^-1 bisphenol A at 2 and 3 V of applied DC potentials was achieved, indicating that the electrochemical filtration process is voltage dependent at both 2 and 3 V. Increasing the residence time by 7.4 fold (from 2.0 to 14.9 s) resulted in a significant removal of bisphenol A and its toxic byproducts, up to 424 min of electrochemical filtration time at 3 V of applied potential. Based on these results, electrochemical filtration using MWNTs is considered a promising technology for the removal of the accumulative bisphenol A and the reduction of its hazardous effects in waters.

Performance of nitrogen-doped graphene aerogel particle electrodes for electro-catalytic oxidation of simulated Bisphenol A wastewaters

The treatment of effluent containing Bisphenol A (BPA) was investigated experimentally using nitrogen-doped graphene aerogel (NGAs) as particle electrodes in a three-dimensional electrode reactor for the electrochemical treatment was studied. The effects of the cell voltage, pH, the ratio of NGAs mass to solution volume and repeated times on the removal efficiency were investigated. Compared with commercial carbon particle electrodes, the NGAs exhibited stronger activity to remove BPA simulated wastewater. For 15mgL^-1 of BPA solution, the degradation rate of BPA exceeded 90% after treatment for only 30min under the optimum conditions. The COD_Cr removal rate of BPA was 85%. Moreover, in the process of reused 50 times, the degradation rate of BPA can be kept in more than 85%. The COD_Cr removal rate was stable at about 73%. The intermediate products of electrochemical degradation of BPA were identified by liquid chromatography-mass spectrometry liquid chromatography (LC-MS), and a probable BPA degradation pathway was proposed. It was considered that OH radicals by water electrolysis could constantly attack the aromatic ring to form various intermediates such as hydroxylated-BPA, isopropylphenol, hydroquinone, phenol and butantetraol, maleic acid, oxalic acid. These compounds were eventually mineralized by electrolysis into CO₂ and H₂O.

Oxidative degradation of bisphenol A and 17α-ethinyl estradiol by Fenton-like activity of silver nanoparticles in aqueous solution

Silver nanoparticles (AgNPs) have been reported to have antibacterial activities and cytotoxicity, resulting from the dissolved silver cation (Ag⁺) and its soluble complexes. However, to our knowledge, little has been reported about their potential use in degrading organic contaminants such as endocrine-disrupting compounds in aqueous solution. In this first report on the subject, we examined the effectiveness of the oxidative degradation of bisphenol A (BPA) and 17α-ethinyl estradiol (EE2) in water by reactive oxygen species formed during the decomposition of H₂O₂, assisted by polyvinylpyrrolidone (PVP)-stabilized AgNPs. The dissolution of AgNPs accompanied generation of OH at low pH. The fully dispersed PVP-AgNPs in the presence of H₂O₂ exhibited fast degradation kinetics for EE2 at a typical aquatic condition of pH (6-7). The oxidation kinetics of BPA and EE2 by PVP-AgNPs can be interpreted using three different modeling approaches: an initial pseudo-first-order, a retarded first-order rate, and Behnajady-Modirshahla-Ghanbery kinetic equation. The findings showed that AgNPs may have potential to facilitate the in situ oxidation for emerging contaminants in the aqueous environment.

Chemical composition and direct electrochemical oxidation of table olive processing wastewater using high oxidation power anodes

Table olive processing wastewater (TOW) is a notoriously polluting due to its high organic and phenol content. To reduce them, an electrochemical process has been studied for the treatment of this effluent. Experiments were performed with a cell equipped with lead dioxide (PbO₂) or boron-doped diamond (BDD) as anode and platinum as cathode, where Table Olive Wastewater (TOW) were destroyed by hydroxyl radicals formed at the anode surface from water oxidation. The comparative study of both systems shows the performance of the BDD anode compared to PbO₂, explained by the large amounts of hydroxyl radicals generated effective at BDD anode and its synthesis characteristics. Using LC/MS analysis, it was possible to determine hydroxytyrosol, as major phenolic compounds, in table olive processing wastewater and its concentration reach 890 mg L^-1. A possible reaction mechanism oxidation for hydroxytyrosol was proposed. The kinetics decays for hydroxytyrosol degradation on PbO₂ anode follows a pseudo-first order reaction with a rate constant 0.9 h^-1 for j_app value 20 mA cm^-2.

Removal of compounds used as plasticizers and herbicides from water by means of gamma irradiation

Gamma radiation has been used to induce the degradation of compounds used as plasticizers and herbicides such as phthalic acid (PA), bisphenol A (BPA), diphenolic acid (DPA), 2,4-dichlorophenoxy-acetic acid (2,4-D), and 4-chloro-2-methylphenoxyacetic acid (MCPA) in aqueous solution, determining the dose constants, removal percentages, and radiation-chemical yields. The reaction rate constants of hydroxyl radical (HO), hydrated electron (eaq(-)) and hydrogen atom (H) with these pollutants were also obtained by means of competition kinetics, using 3-aminopyridine and atrazine as reference compounds. The results indicated that the elimination of these pollutants with gamma radiation mainly follows the oxidative pathway through reaction with HO radicals. The degradation by-products from the five pollutants were determined, detecting that the hydroxylation of the corresponding parent compounds was the main chemical process in the degradation of the pollutants. Moreover, a high decrease in the chemical oxygen demand has been observed for all pollutants. As expected, the degradation by-products generated by the irradiation of PA, BPA and DPA showed a lower toxicity than the parent compounds, however, in the case of 2,4-D and MCPA irradiation, interestingly, their by-products were more toxic than the corresponding original compounds.

Double-Layer 3D Macro-Mesoporous Metal Oxide Modified Boron-Doped Diamond with Enhanced Photoelectrochemical Performance

In this work, a TiO₂/Sb-doped SnO₂ electrode was prepared on the boron-doped diamond (BDD) substrate with double-layer three-dimensional macro-mesoporous (DL3DOM-m) structure, using the polystyrene sphere (PS) vertical deposition method. The as-prepared DL3DOM-m TiO₂/SnO₂/BDD was employed for organic contaminant removal, showing excellent photoelectrocatalytic performance. SEM, XRD and XPS indicated that DL3DOM-m electrode possessed a 3D macroporous layered framework with uniform pore size (about 400 nm), nanosized particles (4.5-5.8 nm), and high electroactive surface area (3-fold more than that of BDD). SA-XRD indicated the backbone of DL3DOM-m electrode had mesoporous structure. It was found that the as-prepared electrode exhibited remarkable electrocatalytic activity, high photocurrent and outstanding absorption capability (91.0 μg cm^-2). Furthermore, bisphenol A (BPA) was completely decomposed after 3 h of reaction applying DL3DOM-m electrode as photoanode, and that on BDD was only 58.9%. It indicated that the modified electrode had great potential to be used in practical water treatment with high photoelectrochemical performance.

Depollution of syringic acid aqueous solutions by electrochemical oxidation using high oxidation power anodes

High oxidation power anodes (PbO₂ or BDD), lead to complete electrochemical removal of syringic acid under particularly experimental conditions.

Removal of phthalates and pharmaceuticals from municipal wastewater by graphene adsorption process

In this work graphene was used for evaluation of its adsorption behavior and performance in removing phthalate esters and pharmaceuticals in municipal wastewater. Di-n-butyl phthalate (DnBP), di-(2-ethylhexyl) phthalate (DEHP), acetaminophen (ACE), caffeine (CAF), cephalexin (CLX), and sulfamethoxazole (SMX) were emerging contaminants (ECs) with detection frequencies over 92% in a one-year monitoring of the occurrence of ECs in influent samples of a sewage treatment plant in Taiwan. Thus, these ECs were selected as the target contaminants for removal by graphene adsorption process. Experimental results showed that the adsorption isotherm data were fitted well to Langmuir model equation. It was also found that the adsorption process obeyed the pseudo-second-order kinetics. A graphene dosage of 0.1 g/L and adsorption time of 12 h were found to be the optimal operating conditions for the ECs of concern in model solutions in a preliminary study. By using the determined optimal operating conditions for removal of such ECs in actual municipal wastewater, removal efficiencies for various ECs were obtained and given as follows: (1) DnBP, 89%, (2) DEHP, 86%, (3) ACE, 43%, (4) CAF, 84%, (5) CLX, 81%, and (6) SMX, 34%.

Mineralization of the antibiotic levofloxacin in aqueous medium by electro-Fenton process: kinetics and intermediate products analysis

The present study investigates the feasibility of using electro-Fenton (EF) process for the oxidative degradation of antibiotic levofloxacin (LEV). The EF experiments have been performed in an electrochemical cell using a carbon-felt cathode. The effect of applied current in the range 60-500 mA and catalyst concentration in the range 0.05-0.5 mM on the kinetics of oxidative degradation and mineralization efficiency have been investigated. Degradation of LEV by hydroxyl radicals was found to follow pseudo-first-order reaction kinetics. The absolute rate constant for oxidative degradation of LEV by hydroxyl radical has been determined by a competition kinetics method and found to be (2.48 ± 0.18) × 10(9) M(-1) s(-1). An optimum current value of 400 mA and a catalyst (Fe(2+)) concentration of 0.1 mM were observed to be optimal for an effective degradation of LEV under our operating conditions. Mineralization of aqueous solution of LEV was performed by the chemical oxygen demand analysis and an almost mineralization degree (>91%) was reached at the end of 6 h of electrolysis. A number of intermediate products have been identified using high performance liquid chromatography and liquid chrmatography-mass spectrometry analyses. Based on these identified reaction intermediates, a plausible reaction pathway has been suggested for the mineralization process. The formation and evolution of [Formula: see text] and [Formula: see text] ions released to the medium during the process were also discussed.

Occurrence and Removal of Organic Micropollutants in Landfill Leachates Treated by Electrochemical Advanced Oxidation Processes

In recent years, electrochemical advanced oxidation processes have been shown to be an effective alternative for the removal of refractory organic compounds from water. This study is focused on the effective removal of recalcitrant organic matter (micropollutants, humic substances, etc.) present in municipal solid waste landfill leachates. A mixture of eight landfill leachates has been studied by the electro-Fenton process using a Pt or boron-doped diamond (BDD) anode and a carbon felt cathode or by the anodic oxidation process with a BDD anode. These processes exhibit great oxidation ability due to the in situ production of hydroxyl radicals ((•)OH), a highly powerful oxidizing species. Both electrochemical processes were shown to be efficient in the removal of dissolved total organic carbon (TOC) from landfill leachates. Regarding the electro-Fenton process, the replacement of the classical anode Pt by the anode BDD allows better performance in terms of dissolved TOC removal. The occurrence and removal yield of 19 polycyclic aromatic hydrocarbons, 15 volatile organic compounds, 7 alkylphenols, 7 polychlorobiphenyls, 5 organochlorine pesticides, and 2 polybrominated diphenyl ethers in landfill leachate were also investigated. Both electrochemical processes allow one to reach a quasicomplete removal (about 98%) of these organic micropollutants.

Fostering the action of versatile peroxidase as a highly efficient biocatalyst for the removal of endocrine disrupting compounds

Response surface methodology (RSM) was used to optimize the removal of five endocrine disrupting compounds (EDCs) by the enzyme versatile peroxidase (VP): bisphenol A (BPA), triclosan (TCS), estrone (E1), 17β-estradiol (E2) and 17α-ethinylestradiol (EE2). The optimal variables of enzyme activity (90-100 U L(-1)), sodium malonate (29-43 mM) and MnSO4 (0.8-1 mM) led to very high removal rates of the five pollutants (2.5-5.0 mg L(-1) min(-1)). The structural elucidation of transformation products arising from the enzymatic catalysis of the EDCs was investigated by Gas Chromatography coupled to Mass Spectrometry (GC-MS) and Liquid Chromatography Electrospray Time-of-Flight Mass Spectrometry (LC-ESI-TOF-MS). The presence of dimers and trimers, indicative of oxidative coupling, was demonstrated.

Carbon nanotube membrane stack for flow-through sequential regenerative electro-Fenton

Electro-Fenton is a promising advanced oxidation process for water treatment consisting a series redox reactions. Here, we design and examine an electrochemical filter for sequential electro-Fenton reactions to optimize the treatment process. The carbon nanotube (CNT) membrane stack (thickness ∼ 200 μm) used here consisted of 1) a CNT network cathode for O2 reduction to H2O2, 2) a CNT-COOFe(2+) cathode to chemical reduction H2O2 to (•)OH and HO(-) and to regenerate Fe(2+) in situ, 3) a porous PVDF or PTFE insulating separator, and 4) a CNT filter anode for remaining intermediate oxidation intermediates. The sequential electro-Fenton was compared to individual electrochemical and Fenton process using oxalate, a persistent organic, as a target molecule. Synergism is observed during the sequential electro-Fenton process. For example, when [DO]in = 38 ± 1 mg L(-1), J = 1.6 mL min(-1), neutral pH, and Ecell = 2.89 V, the sequential electro-Fenton oxidation rate was 206.8 ± 6.3 mgC m(-2) h(-1), which is 4-fold greater than the sum of the individual electrochemistry (16.4 ± 3.2 mgC m(-2) h(-1)) and Fenton (33.3 ± 1.3 mgC m(-2) h(-1)) reaction fluxes, and the energy consumption was 45.8 kWh kgTOC(-1). The sequential electro-Fenton was also challenged with the refractory trifluoroacetic acid (TFA) and trichloroacetic acid (TCA), and they can be transferred at a removal rate of 11.3 ± 1.2 and 21.8 ± 1.9 mmol m(-2) h(-1), respectively, with different transformation mechanisms.

Heterogeneous Fenton catalysts for the abatement of organic pollutants from aqueous solution: a review

Fenton processes have gained much attention in the field of wastewater treatment during recent years.

Electrochemical degradation of refractory pollutants using TiO2 single crystals exposed by high-energy {001} facets

Anodic material plays a vital role in electrochemical water treatment. Titanium dioxide (TiO2) has been widely recognized as an excellent semiconductor photocatalyst, rather than an efficient electrocatalyst, due to its relatively low electric conductivity and poor electrochemical activity. In this work, it is found that TiO2 can actually become a superior electrocatalyst when its crystal shape and exposed facet are finely tuned. The shape-engineered TiO2 single crystals with {001} facets exhibit an excellent electro-catalytic activity and stability for degrading typical organic pollutants such as rhodamine B and bisphenol A, and treating complex landfill leachate. Its electro-catalytic superiority is mainly attributed to the single-crystalline structure and exposed polar {001} facet. Our findings could provide new possibility of utilizing TiO2 for efficient electrochemical water treatment because of its high activity, great stability, low cost and no toxicity.

Monitoring and removal of residual phthalate esters and pharmaceuticals in the drinking water of Kaohsiung City, Taiwan

This study monitored the occurrence and removal efficiencies of 8 phthalate esters (PAEs) and 13 pharmaceuticals present in the drinking water of Kaohsiung City, Taiwan. The simultaneous electrocoagulation and electrofiltration (EC/EF) process was used to remove the contaminants. To this end, a monitoring program was conducted and a novel laboratory-prepared tubular carbon nanofiber/carbon/alumina composite membrane (TCCACM) was incorporated into the EC/EF treatment module (collectively designated as "TCCACM-EC/EF treatment module") to remove the abovementioned compounds from water samples. The monitoring results showed that the concentrations of PAEs were lower in water samples from drinking fountains as compared with tap water samples. No significant differences were found between the concentrations of pharmaceuticals in the two types of water samples. Under optimal operating conditions, the TCCACM-EC/EF treatment module yielded the lowest residual concentrations, ranging from not detected (ND) to 52ng/L for PAEs and pharmaceuticals of concern in the tap water samples. Moreover, the performance of the TCCACM-EC/EF treatment module is comparable with a series of treatment units employed for the drinking fountain water treatment system. The relevant removal mechanisms involved in the TCCACM-EC/EF treatment module were also discussed in this work.

Bisphenol A sorption by organo-montmorillonite: implications for the removal of organic contaminants from water

Remediation of bisphenol A (BPA) from aqueous solutions by adsorption using organoclays synthesized from montmorillonite (MMT) with different types of organic surfactant molecules was demonstrated. High adsorption capacities of the organoclays for the uptake of BPA were observed and these demonstrated their potential application as strong adsorbents for noxious organic water contaminants. The adsorption of BPA was significantly influenced by pH, with increased adsorption of BPA in acidic pH range. However, the organoclays intercalated with highly loaded surfactants and/or large surfactant molecules were less influenced by the pH of the environment and this was thought to be due to the shielding the negative charge from surfactant molecules and the development of more positive charge on the clay surface, which leads to the attraction of anionic BPA even at alkaline pH. The hydrophobic phase created by loaded surfactant molecules contributed to a partitioning phase, interacting with BPA molecules strongly through hydrophobic interaction. Pseudo-second order kinetic model and Langmuir isotherm provided the best fit for the adsorption of BPA onto the organoclays. In addition, the adsorption process was spontaneous and exothermic with lower temperature facilitating the adsorption of BPA onto the organoclays. The described process provides a potential pathway for the removal of BPA from contaminated waters.