Optimization of the thermoelectric figure of merit in the conducting polymer poly(3,4-ethylenedioxythiophene)

Enhanced n-Type Thermoelectric Properties and Structure Evolution of Carbonized Metal-Coordination Polydopamine

Carbonized polydopamine (cPDA) exhibits a nitrogenous graphite-like structure with n-type semiconductor property. However, the low electrical conductivity and Seebeck coefficient of cPDA cannot meet the needs of flexible thermoelectric devices. In this study, a series of metal ions were coordinated with cPDA to enhance n-type thermoelectric properties. At 300 K, all metal-coordination cPDA (metal-cPDA) samples obtain lower thermal conductivity compared to cPDA. Mn-cPDA exhibits the greatest Seebeck coefficient of -25.94 μV K-1, which is almost six times higher than cPDA. Fe-cPDA shows the best electrical conductivity of 2.45 × 105 S m-1. An optimal power factor (PF) value of 11.93 μW m-1 K-2 is achieved in Ca-cPDA with the enhanced electrical conductivity of 9.5 × 104 S m-1 and Seebeck coefficient of -11.24 μV K-1. Using Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, X-ray diffraction (XRD), and transmission electron microscopy (TEM), we revealed the structural characterization of metal-cPDA. Our results indictate that the different metal ions (Mn2+, Zn2+, Mg2+, Al3+, Ca2+, and Fe3+) exert varying influences on the growth of graphite-like structure within metal-cPDA, which lead to the evolution of electrical conductivity. We observe that the carrier density and carrier mobility depend on both the degree of graphitization and the metal-ion coordination, which work together on electrical conductivity and Seebeck coefficient. These findings and understanding of the thermoelectric properties of PDA-based materials will help to realize high-performance n-type thermoelectric materials for flexible electronic device applications.

Material modification of electrodes in microbial electrochemical system to enhance electrons utilization on the electrode and its impact on microorganisms

Previous research has established a MES embedding a microbial electrode to facilitate the degradation of antibiotics in water. We modified microbial electrodes in the MES with PEDOT and rGO to enhance electron utilization on electrodes and to further promote antibiotic degradation. Density functional theory calculations on the SMX molecule indicated that the C4-S8 and S8-N27 bonds are the most susceptible to electron attack. The introduction of various functional groups and multivalent elements enhanced the electrodes' capacitance and electron mediation capabilities. This led to enhance both electron utilization on the electrodes and the removal efficiency of SMX. After 120 h, the degradation efficiency of SMX by PEDOT and rGO-modified electrodes increased by 45.47 % and 25.19 %, respectively, compared to unmodified electrodes. The relative abundance of sulfate-reducing and denitrifying bacteria significantly increased in PEDOT and rGO-modified electrodes, while the abundance of nitrifying bacteria and potential antibiotic resistance gene host microbes significantly decreased. The impact of PEDOT modification positively influenced microbial Cellular Processes, including cell growth, death, and motility. This study provides insights into the mechanisms of direct electron involvement in antibiotic degradation steps in microbial electrochemistry, and provides a possible path for improved strategies in antibiotic degradation and sustainable environmental remediation.

Counterion docking: a general approach to reducing energetic disorder in doped polymeric semiconductors

Molecular doping plays an important role in controlling the carrier concentration of organic semiconductors. However, the introduction of dopant counterions often results in increased energetic disorder and traps due to the molecular packing disruption and Coulomb potential wells. To date, no general strategy has been proposed to reduce the counterion-induced structural and energetic disorder. Here, we demonstrate the critical role of non-covalent interactions (NCIs) between counterions and polymers. Employing a computer-aided approach, we identified the optimal counterions and discovered that NCIs determine their docking positions, which significantly affect the counterion-induced energetic disorder. With the optimal counterions, we successfully reduced the energetic disorder to levels even lower than that of the undoped polymer. As a result, we achieved a high n-doped electrical conductivity of over 200 S cm-1 and an eight-fold increase in the thermoelectric power factor. We found that the NCIs have substantial effects on doping efficiency, polymer backbone planarity, and Coulomb potential landscape. Our work not only provides a general strategy for identifying the most suitable counterions but also deepens our understanding of the counterion effects on doped polymeric semiconductors.

Upscaling Thermoelectrics: Micron-Thick, Half-a-Meter-Long Carbon Nanotube Films with Monolithic Integration of p- and n-Legs

In order for organic thermoelectrics to successfully establish their own niche as energy-harvesting materials, they must reach several crucial milestones, including high performance, long-term stability, and scalability. Performance and stability are currently being actively studied, whereas demonstrations of large-scale compatibility are far more limited and for carbon nanotubes (CNTs) are still missing. The scalability challenge includes material-related economic considerations as well as the availability of fast deposition methods that produce large-scale films that simultaneously satisfy the thickness constraints required for thermoelectric modules. Here we report on true solutions of CNTs that form gels upon air exposure, which can then be dried into micron-thick films. The CNT ink can be extruded using a slot-shaped nozzle into a continuous film (more than half a meter in the present paper) and patterned into alternating n- and p-type components, which are then folded to obtain the finished thermoelectric module. Starting from a given n-type film, differentiation between the n and p components is achieved by a simple postprocessing step that involves a partial oxidation reaction and neutralization of the dopant. The presented method allows the thermoelectric legs to seamlessly interconnect along the continuous film, thus avoiding the need for metal electrodes, and, most importantly, it is compatible with large-scale printing processes. The resulting thermoelectric legs retain 80% of their power factor after 100 days in air and about 30% after 300 days. Using the proposed methodology, we fabricate two thermoelectric modules of 4 and 10 legs that can produce maximum power outputs of 1 and 2.4 μW, respectively, at a temperature difference ΔT of 46 K.

An Electronic Structure Investigation of PEDOT with AlCl4- Anions-A Promising Redox Combination for Energy Storage Applications

In this work, we use density functional theory to investigate the electronic structure of poly(3,4-ethylenedioxythiophene) (PEDOT) oligomers with co-located AlCl4- anions, a promising combination for energy storage. The 1980s bipolaron model remains the dominant interpretation of the electronic structure of PEDOT despite recent theoretical progress that has provided new definitions of bipolarons and polarons. By considering the influence of oligomer length, oxidation or anion concentration and spin state, we find no evidence for many of the assertions of the 1980s bipolaron model and so further contribute to a new understanding. No self-localisation of positive charges in PEDOT is found, as predicted by the bipolaron model at the hybrid functional level. Instead, our results show distortions that exhibit a single or a double peak in bond length alternations and charge density. Either can occur at different oxidation or anion concentrations. Rather than representing bipolarons or polaron pairs in the original model, these are electron distributions driven by a range of factors. Distortions can span an arbitrary number of nearby anions. We also contribute a novel conductivity hypothesis. Conductivity in conducting polymers has been observed to reduce at anion concentrations above 0.5. We show that at high anion concentrations, the energy of the localised, non-bonding anionic orbitals approaches that of the system HOMO due to Coulombic repulsion between anions. We hypothesize that with nucleic motion in the macropolymer, these orbitals will interfere with the hopping of charge carriers between sites of similar energy, lowering conductivity.

Height-renderable morphable tactile display enabled by programmable modulation of local stiffness in photothermally active polymer

Reconfigurable tactile displays are being used to provide refreshable Braille information; however, the delivered information is currently limited to an alternative of Braille because of difficulties in controlling the deformation height. Herein, we present a photothermally activated polymer-bilayer-based morphable tactile display that can programmably generate tangible three-dimensional topologies with varying textures on a thin film surface. The morphable tactile display was composed of a heterogeneous polymer structure that integrated a stiffness-tunable polymer into a light-absorbing elastomer, near-infra-red light-emitting diode (NIR-LED) array, and small pneumatic chamber. Topological expression was enabled by producing localized out-of-plane deformation that was reversible, height-adjustable, and latchable in response to light-triggered stiffness modulation at each target area under switching of stationary pneumatic pressure. Notably, the tactile display could express a spatial softness map of the latched topology upon re-exposing the target areas to modulated light from the NIR-LED array. We expect the developed tactile display to open a pathway for generating high-dimensional tactile information on electronic devices and enable realistic interaction in augmented and virtual environments.

High-performance n-type organic thermoelectrics enabled by modulating cyano-functionalized polythiophene backbones

The scarcity of n-type polymers with high electrical conductivity (σ) and power factor (PF) is the major challenge for organic thermoelectrics (OTEs). By integrating cyano functionalities and an intramolecular conformation lock, we herein synthesize a new electron-deficient building block, CNg4T2, bearing long 1,4,7,10-tetraoxahendecyl side chains, and then further develop two n-type polythiophene derivatives, CNg4T2-2FT and CNg4T2-CNT2, with 3,4-difluorothiophene and 3,3'-dicyano-2,2'-bithiophene as co-units, respectively. Compared with CNg4T2-2FT, CNg4T2-CNT2 features a deeper-positioned lowest unoccupied molecular orbital (LUMO) while maintaining a high degree of backbone coplanarity. As a consequence, the CNg4T2-CNT2 film with molecular dopant N-DMBI delivered an impressive σ of 13.2 S cm-1 and a high PF of up to 10.84 μW m-1 K-2, significantly outperforming CNg4T2-2FT and benchmark n-type polymer N2200 films. To the best of our knowledge, this PF of CNg4T2-CNT2 devices is the highest value for n-type polythiophenes in OTEs. Further characterizations indicate that the high performance of CNg4T2-CNT2-based devices is attributed to the high doping efficiency and ordered packing of polymer chains. Our study demonstrates that CNg4T2 is a highly appealing electron-deficient building block for n-type OTE polymers and also suggests that fine-tuning of the polymer backbone is a powerful approach to accessing high-performance n-type polymers for OTE devices.

Fully inkjet-printed Ag2Se flexible thermoelectric devices for sustainable power generation

Flexible thermoelectric devices show great promise as sustainable power units for the exponentially increasing self-powered wearable electronics and ultra-widely distributed wireless sensor networks. While exciting proof-of-concept demonstrations have been reported, their large-scale implementation is impeded by unsatisfactory device performance and costly device fabrication techniques. Here, we develop Ag2Se-based thermoelectric films and flexible devices via inkjet printing. Large-area patterned arrays with microscale resolution are obtained in a dimensionally controlled manner by manipulating ink formulations and tuning printing parameters. Printed Ag2Se-based films exhibit (00 l)-textured feature, and an exceptional power factor (1097 μWm-1K-2 at 377 K) is obtained by engineering the film composition and microstructure. Benefiting from high-resolution device integration, fully inkjet-printed Ag2Se-based flexible devices achieve a record-high normalized power (2 µWK-2cm-2) and superior flexibility. Diverse application scenarios are offered by inkjet-printed devices, such as continuous power generation by harvesting thermal energy from the environment or human bodies. Our strategy demonstrates the potential to revolutionize the design and manufacture of multi-scale and complex flexible thermoelectric devices while reducing costs, enabling them to be integrated into emerging electronic systems as sustainable power sources.

Biomimetic Exogenous "Tissue Batteries" as Artificial Power Sources for Implantable Bioelectronic Devices Manufacturing

Implantable bioelectronic devices (IBDs) have gained attention for their capacity to conformably detect physiological and pathological signals and further provide internal therapy. However, traditional power sources integrated into these IBDs possess intricate limitations such as bulkiness, rigidity, and biotoxicity. Recently, artificial "tissue batteries" (ATBs) have diffusely developed as artificial power sources for IBDs manufacturing, enabling comprehensive biological-activity monitoring, diagnosis, and therapy. ATBs are on-demand and designed to accommodate the soft and confining curved placement space of organisms, minimizing interface discrepancies, and providing ample power for clinical applications. This review presents the near-term advancements in ATBs, with a focus on their miniaturization, flexibility, biodegradability, and power density. Furthermore, it delves into material-screening, structural-design, and energy density across three distinct categories of TBs, distinguished by power supply strategies. These types encompass innovative energy storage devices (chemical batteries and supercapacitors), power conversion devices that harness power from human-body (biofuel cells, thermoelectric nanogenerators, bio-potential devices, piezoelectric harvesters, and triboelectric devices), and energy transfer devices that receive and utilize external energy (radiofrequency-ultrasound energy harvesters, ultrasound-induced energy harvesters, and photovoltaic devices). Ultimately, future challenges and prospects emphasize ATBs with the indispensability of bio-safety, flexibility, and high-volume energy density as crucial components in long-term implantable bioelectronic devices.

High Thermoelectric Performance in Solution-Processed Semicrystalline PEDOT:PSS Films by Strong Acid-Base Treatment: Limitations and Potential

Thermoelectric (TE) generation with solution-processable conducting polymers offers substantial potential in low-temperature energy harvesting based on high tunability in materials, processes, and form-factors. However, manipulating the TE and charge transport properties accompanies structural and energetic disorders, restricting the enhancement of thermoelectric power factor (PF). Here, solution-based strong acid-base treatment techniques are introduced to modulate the doping level of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin films with preserving its molecular orientation, enabling to achieve a remarkably high PF of 534.5 µW m-1  K-2 . Interestingly, theoretical modeling suggested that further de-doping can increase the PF beyond the experimental value. However, it is impossible to reach this value experimentally, even without any degradation of PEDOT crystallinity. Uncovering the underlying reason for the limitation, an analysis of the relationship among the microstructure-thermoelectric performance-charge transport property revealed that inter-domain connectivity via tie-chains and the resultant percolation for transport are crucial factors in achieving high TE performance, as in charge transport. It is believed that the methods and fundamental understandings in this work would contribute to the exploitation of conducting polymer-based low-temperature energy harvesting.

Advanced Thermoelectric Textiles for Power Generation: Principles, Design, and Manufacturing

Self-powered wearable thermoelectric (TE) devices significantly reduce the inconvenience caused to users, especially in daily use of portable devices and monitoring personal health. The textile-based TE devices (TETs) exhibit the excellent flexibility, deformability, and light weight, which fulfill demands of long-term wearing for the human body. In comparison to traditional TE devices with their longstanding research history, TETs are still in an initial stage of growth. In recent years, TETs to provide electricity for low-power wearable electronics have attracted increasing attention. This review summarizes the recent progress of TETs from the points of selecting TE materials, scalable fabrication methods of TE fibers/yarns and TETs, structure design of TETs and reported high-performance TETs. The key points to develop TETs with outstanding TE properties and mechanical performance and better than available optimization strategies are discussed. Furthermore, remaining challenges and perspectives of TETs are also proposed to suggest practical applications for heat harvesting from human body.

Thermoelectric Power of a Single van der Waals Interface between Carbon Nanotubes

Control of van der Waals interfaces is crucial for fabrication of nanomaterial-based high-performance thermoelectric devices because such interfaces significantly affect the overall thermoelectric performances of the device due to their relatively high thermal resistance. Such interfaces could induce different thermoelectric power from the bulk, i.e., interfacial thermoelectric power. However, from a macroscopic point of view, a correct evaluation of the interfacial thermoelectric power is difficult owing to various interface configurations. Therefore, the study of the thermoelectric properties at a single interface is crucial to address this problem. Herein, we used in situ transmission electron microscopy and nanomanipulation to investigate the thermoelectric properties of carbon nanotubes and their interfaces. The thermoelectric power of the bridged carbon nanotubes was individually measured. The existence of the interfacial thermoelectric power was determined by systematically changing the contact size between the two parallel nanotubes. The effect of interfacial thermoelectric power was qualitatively supported by Green's function calculations. When the contact length between two parallel nanotubes was less than approximately 100 nm, the experimental results and theoretical calculations indicated that the interface significantly contributed to the total thermoelectric power. However, when the contact length was longer than approximately 200 nm, the total thermoelectric power converged to the value of a single nanotube. The findings herein provide a basis for investigating thermoelectric devices with controlled van der Waals interfaces and contribute to thermal management in nanoscale devices and electronics.

Combining Step-Growth and Chain-Growth Polymerizations in One Pot: Light-Induced Fabrication of Conductive Nanoporous PEDOT-PCL Scaffold

A novel method based on light-induced fabrication of a poly (3,4-ethylenedioxythiophene)-polycaprolactone (PEDOT-PCL) scaffold using phenacyl bromide (PAB) as a single-component photoinitiator is presented. HBr released from the step-growth polymerization of EDOT is utilized as an in situ catalyst for the chain-growth polymerization of ε-caprolactone. Detailed investigations disclose the formation of a self-assembled nanoporous electroconductive scaffold (1.2 mS cm-1 ). Fluorescence emission spectra of the fabricated scaffold exhibit a mixed solvatochromic behavior, indicating specific interactions between the self-assembled scaffold and solvents with varying polarities, as evidenced by transmission electron microscopy (TEM). Moreover, the same light-induced technique can also be applied for bulk photopolymerization showcasing the versatility and wide-ranging scope of the originated method. In brief, this study introduces a novel approach for light-induced polymerization reactions that is merging step-growth and chain-growth mechanisms. This innovative approach is promising to facilitate in situ polymerization of monomers possessing diverse functionalities.

Carrier Screening Controls Transport in Conjugated Polymers at High Doping Concentrations

Transport properties of doped conjugated polymers (CPs) have been widely analyzed with the Gaussian disorder model (GDM) in conjunction with hopping transport between localized states. These models reveal that even in highly doped CPs, a majority of carriers are still localized because dielectric permittivity of CPs is well below that of inorganic materials, making Coulomb interactions between carriers and dopant counterions much more pronounced. However, previous studies within the GDM did not consider the role of screening the dielectric interactions by carriers. Here we implement carrier screening in the Debye-Hückel formalism in our calculations of dopant-induced energetic disorder, which modifies the Gaussian density of states (DOS). Then we solve the Pauli master equation using Miller-Abrahams hopping rates with states from the resulting screened DOS to obtain conductivity and Seebeck coefficient across a broad range of carrier concentrations and compare them to measurements. Our results show that screening has significant impact on the shape of the DOS and consequently on carrier transport, particularly at high doping. We prove that the slope of Seebeck coefficient versus electric conductivity, which was previously thought to be universal, is impacted by screening and decreases for systems with small dopant-carrier separation, explaining our measurements. We also show that thermoelectric power factor is underestimated by a factor of ∼10 at higher doping concentrations if screening is neglected. We conclude that carrier screening plays a crucial role in curtailing dopant-induced energetic disorder, particularly at high carrier concentrations.

Heterogeneous Oriented Structure model of thermoelectric transport in conducting polymers

Understanding transport phenomena in conducting polymers (CP) is a main issue in order to optimize their performance and despite intense investigations, the influence of their microstructure remains controversial. By analyzing the thermoelectric measurements performed on highly oriented and non-oriented CP films, we show that an Heterogeneous Oriented Structure (HOSt) model considering both ordered and disordered domains is able to account for the thermoelectric transport in CP. This model unveils the key role of the crystallinity, the anisotropy and the alignment degree of these domains. It points out the importance of the thermal conductivity in the interpretation of the thermopower [Formula: see text] and explains the frequently observed electrical conductivity [Formula: see text] cut-off in the [Formula: see text] curves due to the disordered domains. By varying the alignment degree depending on the orientation and the anisotropy according to the face-on or the edge-on polymers conformation, the HOSt model successfully describes the overall measured thermoelectric properties by demonstrating its applicability to a wide variety of both oriented and non-oriented CP.

Surface Functionalization with (3-Glycidyloxypropyl)trimethoxysilane (GOPS) as an Alternative to Blending for Enhancing the Aqueous Stability and Electronic Performance of PEDOT:PSS Thin Films

Organic mixed ionic-electronic conductors, such as poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), are essential materials for the fabrication of bioelectronic devices due to their unique ability to couple and transport ionic and electronic charges. The growing interest in bioelectronic devices has led to the development of organic electrochemical transistors (OECTs) that can operate in aqueous solutions and transduce ionic signals of biological origin into measurable electronic signals. A common challenge with OECTs is maintaining the stability and performance of the PEDOT:PSS films operating under aqueous conditions. Although the conventional approach of blending the PEDOT:PSS dispersions with a cross-linker such as (3-glycidyloxypropyl)trimethoxysilane (GOPS) helps to ensure strong adhesion of the films to device substrates, it also impacts the morphology and thus electrical properties of the PEDOT:PSS films, which leads to a significant reduction in the performance of OECTs. In this study, we instead functionalize only the surface of the device substrates with GOPS to introduce a silane monolayer before spin-coating the PEDOT:PSS dispersion on the substrate. In all cases, having a GOPS monolayer instead of a blend leads to increased electronic performance metrics, such as three times higher electronic conductivity, volumetric capacitance, and mobility-capacitance product [μC*] value in OECT devices, ultimately leading to a record value of 406 ± 39 F cm-1 V-1 s-1 for amorphous PEDOT:PSS. This increased performance does not come at the expense of operational stability, as both the blend and surface functionalization show similar performance when subjected to pulsed gate bias stress, long-term electrochemical cycling tests, and aging over 150 days. Overall, this study establishes a novel approach to using GOPS as a surface monolayer instead of a blended cross-linker, for achieving high-performance organic mixed ionic-electronic conductors that are stable in water for bioelectronics.

Energy Applications of Ionic Liquids: Recent Developments and Future Prospects

Ionic liquids (ILs) consisting entirely of ions exhibit many fascinating and tunable properties, making them promising functional materials for a large number of energy-related applications. For example, ILs have been employed as electrolytes for electrochemical energy storage and conversion, as heat transfer fluids and phase-change materials for thermal energy transfer and storage, as solvents and/or catalysts for CO2 capture, CO2 conversion, biomass treatment and biofuel extraction, and as high-energy propellants for aerospace applications. This paper provides an extensive overview on the various energy applications of ILs and offers some thinking and viewpoints on the current challenges and emerging opportunities in each area. The basic fundamentals (structures and properties) of ILs are first introduced. Then, motivations and successful applications of ILs in the energy field are concisely outlined. Later, a detailed review of recent representative works in each area is provided. For each application, the role of ILs and their associated benefits are elaborated. Research trends and insights into the selection of ILs to achieve improved performance are analyzed as well. Challenges and future opportunities are pointed out before the paper is concluded.

A PEDOT:PSS/MXene-based actuator with self-powered sensing function by incorporating a photo-thermoelectric generator

Actuators with sensing functions are becoming increasingly important in the field of soft robotics. However, most of the actuators are lack of self-powered sensing ability, which limits their applications. Here, we report a light-driven actuator with self-powered sensing function, which is designed to incorporate a photo-thermoelectric generator into the actuator based on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/MXene composite and polyimide. The actuator shows a large bending curvature of 1.8 cm-1 under near-infrared light (800 mW cm-2) irradiation for 10 s, which is attribute to photothermal expansion mismatch between PEDOT:PSS/MXene composite and polyimide. Simultaneously, the actuator shows enhanced thermoelectric properties with Seebeck coefficient of 35.7 μV K-1, which are mainly attributed to a combination of energy filtering effects between the PEDOT:PSS and MXene interfaces as well as the synergistic effect of its charge carrier migration. The output voltage of the actuator changes in accordance with the bending curvature, so as to achieve the self-powered sensing function and monitor the operating state of the actuator. Moreover, a bionic flower is fabricated, which not only simulates the blooming and closing of the flower, but also perceives the real-time actuation status through the output voltage signal. Finally, a smart Braille system is elaborately designed, which can not only simulate Braille characters for tactile recognition of the blind people, but also automatically output the voltage signal of Braille for self-powered sensing, enabling multi-channel output and conversion of light energy. This research proposes a new idea for exploring multifunctional actuators, integrated devices and self-powered soft robots.

Charge carrier dynamics in conducting polymer PEDOT using ab initio molecular dynamics simulations

As conducting polymers become increasingly important in electronic devices, understanding their charge transport is essential for material and device development. Various semi-empirical approaches have been used to describe temporal charge carrier dynamics in these materials, but there have yet to be any theoretical approaches utilizing ab initio molecular dynamics. In this work, we develop a computational technique based on ab initio Car-Parrinello molecular dynamics to trace charge carrier temporal motion in archetypical conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT). Particularly, we analyze charge dynamics in a single PEDOT chain and in two coupled chains with different degrees of coupling and study the effect of temperature. In our model we first initiate a positively charged polaron (compensated by a negative counterion) at one end of the chain, and subsequently displace the counterion to the other end of the chain and trace polaron dynamics in the system by monitoring bond length alternation in the PEDOT backbone and charge density distribution. We find that at low temperature (T = 1 K) the polaron distortion gradually disappears from its initial location and reappears near the new position of the counterion. At the room temperature (T = 300 K), we find that the distortions induced by polaron, and atomic vibrations are of the same magnitude, which makes tracking the polaron distortion challenging because it is hidden behind the temperature-induced vibrations. The novel approach developed in this work can be used to study polaron mobility along and between the chains, investigate charge transport in highly doped polymers, and explore other flexible polymers, including n-doped ones.

High-Performance n-Type Organic Thermoelectrics Enabled by Synergistically Achieving High Electron Mobility and Doping Efficiency

n-Doped polymers with high electrical conductivity (σ) are still very scarce in organic thermoelectrics (OTEs), which limits the development of efficient organic thermoelectric generators. A series of fused bithiophene imide dimer-based polymers, PO8, PO12, and PO16, incorporating distinct oligo(ethylene glycol) side-chain to optimize σ is reported here. Three polymers show a monotonic electron mobility decrease as side-chain size increasing due to the gradually lowered film crystallinity and change of backbone orientation. Interestingly, polymer PO12 with a moderate side-chain size delivers a champion σ up to 92.0 S cm-1 and a power factor (PF) as high as 94.3 µW m-1 K-2 in the series when applied in OTE devices. The PF value is among the highest ones for the solution-processing n-doped polymers. In-depth morphology studies unravel that the moderate crystallinity and the formation of 3D conduction channel derived from bimodal orientation synergistically contribute to high doping efficiency and large charge carrier mobility, thus resulting in high performance for the PO12-based OTEs. The results demonstrate the great power of simple tuning of side chain in developing n-type polymers with substantial σ for improving organic thermoelectric performance.

Heterodimensional Structure Switching Multispectral Stealth and Multimedia Interaction Devices

Lightweight and flexible electronic materials with high energy attenuation hold an unassailable position in electromagnetic stealth and intelligent devices. Among them, emerging heterodimensional structure draws intensive attention in the frontiers of materials, chemistry, and electronics, owing to the unique electronic, magnetic, thermal, and optical properties. Herein, an intrinsic heterodimensional structure consisting of alternating assembly of 0D magnetic clusters and 2D conductive layers is developed, and its macroscopic electromagnetic properties are flexibly designed by customizing the number of oxidative molecular layer deposition (oMLD) cycles. This unique heterodimensional structure features highly ordered spatial distribution, with an achievement of electron-dipole and magnetic-dielectric double synergies, which exhibits the high attenuation of electromagnetic energy (160) and substantial improvement of dielectric loss tangent (≈200%). It can respond to electromagnetic waves of different bands to achieve multispectral stealth, covering visible light, infrared radiation, and gigahertz wave. Importantly, two kinds of ingenious information interaction devices are constructed with heterodimensional structure. The hierarchical antennas allow precise targeting of operating bands (S- to Ku- bands) by oMLD cycles. The strain imaging device with high sensitivity opens a new horizon for visual interaction. This work provides a creative insight for developing advanced micro-nano materials and intelligent devices.

Chemical Doping of Organic and Coordination Polymers for Thermoelectric and Spintronic Applications: A Theoretical Understanding

ConspectusThe controlled doping of organic semiconductors (OSCs) is crucial not only for improving the performance of electronic and optoelectronic devices but also for enabling efficient thermoelectric conversion and spintronic applications. The mechanism of doping for OSCs is fundamentally different from that of their inorganic counterparts. In particular, the interplay between dopants and host materials is complicated considering the low dielectric constant, strong lattice-charge interaction, and flexible nature of materials. Recent experimental breakthroughs in the molecular design of dopants and the precise doping with high spatial resolution call for more profound understandings as to how the dopant interacts with the charge introduced to OSCs and how the admixture of dopants alters the electronic properties of host materials before one can exploit controllable doping to realize desired functionalities.By employing state-of-the-art computational tools, we revealed the effects of doping in representative and emerging organic and coordination polymers aiming toward thermoelectric and spintronic applications. We showed that dopants and hosts should be taken as an integrated system, and the type of charge-transfer interaction between them is the key for spin polarization. First, we found doping-induced modifications to the electronic band in a potassium-doped coordination polymer, an n-type thermoelectric material. The charge localization due to the Coulomb interaction between the completely ionized dopant and the injected charge on the polymer backbone and also the polaron band formation at low doping levels are responsible for the nonmonotonic temperature dependence of the conductivity and Seebeck coefficient observed in recent experiments. The mechanistic insights gained from these results have provided important guidelines on how to control the doping level and working temperature to achieve a high thermoelectric conversion efficiency. Next, we demonstrated that the ionized dopants scatter charge carriers via screened Coulomb interactions, and it may become a dominant scattering mechanism in doped polymers. After incorporating the ionized dopant scattering mechanism in PEDOT:Tos, a p-type thermoelectric polymer, we were able to reproduce the measured Seebeck coefficient-electrical conductivity relationship spanning a wide range of doping levels, highlighting the importance of ionized dopant scattering in charge transport.In the two cases described above, charge injection is enabled by integral charge transfer between the dopant and host polymers. In a third example, we showed that a novel type of stacked two-dimensional polymer, conjugated covalent organic frameworks (COFs) with closed-shell electronic structures, can be spin polarized by iodine doping via fractional charge transfer even at high doping levels. We then manifested that magnetization can be attained in nonmagnetic materials lacking metal d electrons and further designed two new COFs with tunable spintronic structure and magnetic interactions after the iodine doping. These findings have suggested a practical route to enable spin polarization in nonradical materials by chemical doping via orbital hybridization, which holds great promise for flexible spintronic applications.

Thermoelectric Characteristics of Self-Supporting WSe2-Nanosheet/PEDOT-Nanowire Composite Films

Conducting polymer poly(3,4-ethylenedioxythiophene) nanowires (PEDOT NWs) were synthesized by a modified self-assembled micellar soft-template method, followed by fabrication by vacuum filtration of self-supporting exfoliated WSe₂-nanosheet (NS)/PEDOT-NW composite films. The results showed that as the mass fractions of WSe₂ NSs increased from 0 to 20 wt % in the composite films, the electrical conductivity of the samples decreased from ∼1700 to ∼400 S cm^-1, and the Seebeck coefficient increased from 12.3 to 23.1 μV K^-1 at 300 K. A room-temperature power factor of 44.5 μW m^-1 K^-2 was achieved at 300 K for the sample containing 5 wt % WSe₂ NSs, and a power factor of 67.3 μW m^-1 K^-2 was obtained at 380 K. The composite film containing 5 wt % WSe₂ NSs was mechanically flexible, as shown by its resistance change ratio of 7.1% after bending for 500 cycles at a bending radius of 4 mm. A flexible thermoelectric (TE) power generator containing four TE legs could generate an output power of 52.1 nW at a temperature difference of 28.5 K, corresponding to a power density of ∼0.33 W/m². This work demonstrates that the fabrication of inorganic nanosheet/organic nanowire TE composites is an approach to improve the TE properties of conducting polymers.

Elucidating Design Rules toward Enhanced Solid-State Charge Transport in Oligoether-Functionalized Dioxythiophene-Based Alternating Copolymers

This study investigates the solid-state charge transport properties of the oxidized forms of dioxythiophene-based alternating copolymers consisting of an oligoether-functionalized 3,4-propylenedioxythiophene (ProDOT) copolymerized with different aryl groups, dimethyl ProDOT (DMP), 3,4-ethylenedioxythiophene (EDOT), and 3,4-phenylenedioxythiophene (PheDOT), respectively, to yield copolymers P(OE3)-D, P(OE3)-E, and P(OE3)-Ph. At a dopant concentration of 5 mM FeTos₃, the electrical conductivities of these copolymers vary significantly (ranging between 9 and 195 S cm^-1) with the EDOT copolymer, P(OE3)-E, achieving the highest electrical conductivity. UV-vis-NIR and X-ray spectroscopies show differences in both susceptibility to oxidative doping and extent of oxidation for the P(OE3) series, with P(OE3)-E being the most doped. Wide-angle X-ray scattering measurements indicate that P(OE3)-E generally demonstrates the lowest paracrystallinity values in the series, as well as relatively small π-π stacking distances. The significant (i.e., order of magnitude) increase in electrical conductivity of doped P(OE3)-E films versus doped P(OE3)-D or P(OE3)-Ph films can therefore be attributed to P(OE3)-E exhibiting both the highest carrier ratios in the P(OE3) series, along with good π-π overlap and local ordering (low paracrystallinity values). Furthermore, these trends in the extent of doping and paracrystallinity are consistent with the reduced Fermi energy level and transport function prefactor parameters calculated using the semilocalized transport (SLoT) model. Observed differences in carrier ratios at the transport edge (c_t) and reduced Fermi energies [η(c)] suggest a broader electronic band (better overlap and more delocalization) for the EDOT-incorporating P(OE3)-E polymer relative to P(OE3)-D and P(OE3)-Ph. Ultimately, we rationalize improvements in electrical conductivity due to microstructural and doping enhancements caused by EDOT incorporation, a structure-property relationship worth considering in the future design of highly electrically conductive systems.

Incommensurately Modulated Structure in AgCuSe-Based Thermoelectric Materials for Intriguing Electrical, Thermal, and Mechanical Properties

AgCuSe-based materials have attracted great attentions recently in thermoelectric (TE) field due to their extremely high electron mobility, ultralow lattice thermal conductivity, and abnormal "brittle-ductile" transition at room temperature. However, although the investigation on the crystal structure of AgCuSe low-temperature phase (named as β-AgCuSe) was started more than half a century before, it is still in controversy yet, which greatly limits the understanding of its intriguing electrical, thermal, and mechanical performance. In this work, via adopting the advanced three-dimensional electron diffraction technique, this study finds that the AgCuSe-based materials crystalize in an incommensurately modulated structure with an orthorhombic Pmmn(0β1/2)s00 superspace group. The local lattice distortion in the incommensurately modulated structure has weak effects on the conduction band minimum due to the delocalized and isotropic feature of Ag 5s states, leading to high carrier mobility. Likewise, the inhomogeneous, weak, and anisotropic Ag-Se bonds result in the high degree of anharmonicity and ultralow lattice thermal conductivity. Furthermore, alloying S in AgCuSe reinforces the interaction between the adjacent Ag-Se layers, yielding the "brittle-ductile" transition at room temperature. This work well interprets the structure-performance relationship of AgCuSe-based materials and sheds light on the future investigation of this class of promising TE materials.

Oxidative Molecular Layer Deposition Tailoring Eco-Mimetic Nanoarchitecture to Manipulate Electromagnetic Attenuation and Self-Powered Energy Conversion

Advanced electromagnetic devices, as the pillars of the intelligent age, are setting off a grand transformation, redefining the structure of society to present pluralism and diversity. However, the bombardment of electromagnetic radiation on society is also increasingly serious along with the growing popularity of "Big Data". Herein, drawing wisdom and inspiration from nature, an eco-mimetic nanoarchitecture is constructed for the first time, highly integrating the advantages of multiple components and structures to exhibit excellent electromagnetic response. Its electromagnetic properties and internal energy conversion can be flexibly regulated by tailoring microstructure with oxidative molecular layer deposition (oMLD), providing a new cognition to frequency-selective microwave absorption. The optimal reflection loss reaches ≈  - 58 dB, and the absorption frequency can be shifted from high frequency to low frequency by increasing the number of oMLD cycles. Meanwhile, a novel electromagnetic absorption surface is designed to enable ultra-wideband absorption, covering almost the entire K and Ka bands. More importantly, an ingenious self-powered device is constructed using the eco-mimetic nanoarchitecture, which can convert electromagnetic radiation into electric energy for recycling. This work offers a new insight into electromagnetic protection and waste energy recycling, presenting a broad application prospect in radar stealth, information communication, aerospace engineering, etc.

Flexible Active Peltier Coolers Based on Interconnected Magnetic Nanowire Networks

Thermoelectric energy conversion based on flexible materials has great potential for applications in the fields of low-power heat harvesting and solid-state cooling. Here, we show that three-dimensional networks of interconnected ferromagnetic metal nanowires embedded in a polymer film are effective flexible materials as active Peltier coolers. Thermocouples based on Co-Fe nanowires exhibit much higher power factors and thermal conductivities near room temperature than other existing flexible thermoelectric systems, with a power factor for Co-Fe nanowire-based thermocouples of about 4.7 mW/K2m at room temperature. The effective thermal conductance of our device can be strongly and rapidly increased by active Peltier-induced heat flow, especially for small temperature differences. Our investigation represents a significant advance in the fabrication of lightweight flexible thermoelectric devices, and it offers great potential for the dynamic thermal management of hot spots on complex surfaces.

Double-photoelectrode redox desalination of seawater

High energy consumption and low salt removal rate are key barriers to realizing practical electrochemical seawater desalination processes. Here, we demonstrate a novel solar-driven redox flow desalination device with double photoelectrodes to achieve efficient desalination without electrical energy consumption. The device consists of three parts: one photoanode unit, one photocathode unit, and one redox flow desalination unit sandwiched between the two photoelectrode units. The photoelectrode units include a TiO₂ photoanode and a NiO photocathode sensitized with N719 dye, triiodide/iodide redox electrolyte, and graphite paper integrated electrodes decorated with 3,4-ethylene-dioxythiophene. Two salt feeds are located between two ferro/ferricyanide redox flow chambers. Under light illumination, high-quality freshwater is obtained from brackish water containing different concentrations of NaCl from 1000 to 12,000 ppm with a high NaCl removal rate. The device can work in multiple desalination cycles without significant performance declines. Furthermore, natural seawater with an ionic conductivity of 53.45 mS cm^-1 is desalinated to freshwater. This new design opens opportunities to realize efficient and practical solar-driven desalination processes.

Charge transport transition of PEDOT:PSS thin films for temperature-insensitive wearable strain sensors

In this study, a temperature-insensitive strain sensor that detects only the strain without responding to the temperature was designed. The transport mechanism and associated temperature coefficient of resistance (TCR) of a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin film were modified through secondary doping with dimethyl sulfoxide (DMSO). Upon DMSO-doping, the carrier transport mechanism of the PEDOT:PSS thin film transitioned from hopping to band-like transport, with a morphological change. At the DMSO doping level, which caused the critical point of the transport transition, the resistance of the thin film was maintained with a change in temperature. Consequently, the TCR of the optimized PEDOT:PSS thin film was less than 9 × 10^-5 K^-1, which is 10² times lower than that of the as-prepared films. The carrier mobility of the PEDOT:PSS thin film was effectively improved with the morphological change due to DMSO doping and was investigated through combinational analysis. Ultimately, the wearable strain sensor prepared using the optimized PEDOT:PSS thin film responded stably to the applied strain with a gauge factor of 2 and exhibited excellent temperature anti-interference.

Superflexible Inorganic Ag2 Te0.6 S0.4 Fiber with High Thermoelectric Performance

Fiber-based inorganic thermoelectric (TE) devices, owing to the small size, light-weight, flexibility, and high TE performance, are promising for applications in flexible thermoelectrics. Unfortunately, current inorganic TE fibers are strictly constrained by limited mechanical freedom because of the undesirable tensile strain, typically limited to a value of 1.5%, posing a strong obstacle for further application in large-scale wearable systems. Here, a superflexible Ag₂ Te_0.6 S_0.4 inorganic TE fiber is demonstrated that provides a record tensile strain of 21.2%, such that it enables various complex deformations. Importantly, the TE performance of the fiber shows high stability after ≈1000 cycles of bending and releasing processes with a small bending radius of 5 mm. This allows for the integration of the inorganic TE fiber into 3D wearable fabric, yielding a normalized power density of 0.4 µW m^-1 K^-2 under the temperature difference of 20 K, which is approaching the high-performance Bi₂ Te₃ -based inorganic TE fabric and is nearly two orders of magnitude higher than the organic TE fabrics. These results highlight that the inorganic TE fiber with both superior shape-conformable ability and high TE performance may find potential applications in wearable electronics.

Highly conductive tissue-like hydrogel interface through template-directed assembly

Over the past decade, conductive hydrogels have received great attention as tissue-interfacing electrodes due to their soft and tissue-like mechanical properties. However, a trade-off between robust tissue-like mechanical properties and good electrical properties has prevented the fabrication of a tough, highly conductive hydrogel and limited its use in bioelectronics. Here, we report a synthetic method for the realization of highly conductive and mechanically tough hydrogels with tissue-like modulus. We employed a template-directed assembly method, enabling the arrangement of a disorder-free, highly-conductive nanofibrous conductive network inside a highly stretchable, hydrated network. The resultant hydrogel exhibits ideal electrical and mechanical properties as a tissue-interfacing material. Furthermore, it can provide tough adhesion (800 J/m²) with diverse dynamic wet tissue after chemical activation. This hydrogel enables suture-free and adhesive-free, high-performance hydrogel bioelectronics. We successfully demonstrated ultra-low voltage neuromodulation and high-quality epicardial electrocardiogram (ECG) signal recording based on in vivo animal models. This template-directed assembly method provides a platform for hydrogel interfaces for various bioelectronic applications.

Boosting the Thermoelectric Performance of the Doped DPP-EDOT Conjugated Polymer by Incorporating an Ionic Additive

The thermoelectric (TE) performance of organic materials is limited by the coupling of Seebeck coefficient and electrical conductivity. Herein a new strategy is reported to boost the Seebeck coefficient of conjugated polymer without significantly reducing the electrical conductivity by incorporation of an ionic additive DPPNMe₃ Br. The doped polymer PDPP-EDOT thin film exhibits high electrical conductivity up to 1377 ± 109 S cm^-1 but low Seebeck coefficient below 30 µV K^-1 and a maximum power factor of 59 ± 10 µW m^-1 K^-2 . Interestingly, incorporation of small amount (at a molar ratio of 1:30) of DPPNMe₃ Br into PDPP-EDOT results in the significant enhancement of Seebeck coefficient along with the slight decrease of electrical conductivity after doping. Consequently, the power factor (PF) is boosted to 571 ± 38 µW m^-1 K^-2 and ZT reaches 0.28 ± 0.02 at 130 °C, which is among the highest for the reported organic TE materials. Based on the theoretical calculation, it is assumed that the enhancement of TE performance for the doped PDPP-EDOT by DPPNMe₃ Br is mainly attributed to the increase of energetic disorder for PDPP-EDOT.

Organic thermoelectric generators: working principles, materials, and fabrication techniques

Organic thermoelectricity is a blooming field of research that employs organic (semi)conductors to recycle waste heat through its partial conversion to electrical power. Such a conversion occurs by means of organic thermoelectric generator (OTEG) devices. The recent process on the synthesis of novel materials and on the understanding of doping mechanisms to increase conductivity has tremendously narrowed the gap between laboratory research and their application in actual applications. This Feature Article intends to highlight the impressive progress in materials and fabrication techniques for OTEGs made in recent years.

Revealing the Enhanced Thermoelectric Properties of Controllably Doped Donor-Acceptor Copolymer: The Impact of Regioregularity

Albeit considerable attention to the fast-developing organic thermoelectric (OTE) materials due to their flexibility and non-toxic features, it is still challenging to design an OTE polymer with superior thermoelectric properties. In this work, two "isomorphic" donor-acceptor (D-A) conjugated polymers are studied as the semiconductor in OTE devices, revealing for the first time the internal mechanism of regioregularity on thermoelectric performances in D-A type polymers. A higher molecular structure regularity can lead to higher crystalline order and mobility, higher doping efficiency, order of energy state, and thermoelectric (TE) performance. As a result, the regioregular P2F exhibits a maximum power factor (PF) of up to 113.27 µW m^-1  K^-2 , more than three times that of the regiorandom PRF (35.35 µW m^-1  K^-2 ). However, the regular backbone also implies lower miscibility with a dopant, negatively affecting TE performance. Therefore, the trade-off between doping efficiency and miscibility plays a vital role in OTE materials, and this work sheds light on the molecular design strategy of OTE polymers with state-of-the-art performances.

Self-Healing Polymers for Electronics and Energy Devices

Polymers are extensively exploited as active materials in a variety of electronics and energy devices because of their tailorable electrical properties, mechanical flexibility, facile processability, and they are lightweight. The polymer devices integrated with self-healing ability offer enhanced reliability, durability, and sustainability. In this Review, we provide an update on the major advancements in the applications of self-healing polymers in the devices, including energy devices, electronic components, optoelectronics, and dielectrics. The differences in fundamental mechanisms and healing strategies between mechanical fracture and electrical breakdown of polymers are underlined. The key concepts of self-healing polymer devices for repairing mechanical integrity and restoring their functions and device performance in response to mechanical and electrical damage are outlined. The advantages and limitations of the current approaches to self-healing polymer devices are systematically summarized. Challenges and future research opportunities are highlighted.

Solution-Processable PEDOT Particles for Coatings of Untreated 3D-Printed Thermoplastics

Lack of solution processability is the main bottleneck in research progression and commercialization of conducting polymers. The current strategy of employing a water-soluble dopant (such as PEDOT:PSS) is not feasible with organic solvents, thus limiting compatibility on hydrophobic surfaces, such as three-dimensional (3D) printable thermoplastics. In this article, we utilize a colloidal dispersion of PEDOT particles to overcome this limitation and formulate an organic paint demonstrating conformal coating on 3D-printed objects. We start with synthesizing PEDOT particles that possess a low electrical resistance (gap resistance of 4.2 ± 0.5 Ω/mm). A particle-based organic paint is formulated and applied via brush painting. Coated objects show a surface resistance of 1 kΩ/cm, comparable to an object printed by commercial conductive filaments. The coating enables the fabrication of pH and strain sensors. Highly conductive PEDOT particles also absorb light strongly, especially in the near-infrared (NIR) range due to the high concentration of charge carriers on the polymer's conjugated backbones (i.e., polarons and bipolarons). PEDOT converts light to heat efficiently, resulting in a superior photothermal activity that is demonstrated by the flash ignition of a particle-impregnated cotton ball. Consequently, painted 3D prints are highly effective in converting NIR light to heat, and a 5 s exposure to a NIR laser (808 nm, 0.8 mW/cm²) leads to a record high-temperature increase (194.5 °C) among PEDOT-based coatings.

Vitamin C-Induced Enhanced Performance of PEDOT:PSS Thin Films for Eco-Friendly Transient Thermoelectrics

Conjugated polymer-based energy-harvesting devices hold distinctive advantages in terms of low toxicity, high flexibility, and capability of large-area integration at low cost for sustainable development. An organic thermoelectric (OTE) device has been considered one of the promising energy-harvesting candidates in recent years because it can efficiently convert low-temperature waste heat into electricity over its inorganic counterparts. However, a cruel irony is that environmentally toxic solvents and acids are utilized for fabrication and performance improvement of the OTE devices, retarding the development and use of genuinely green energy-harvesting. Here, we present eco-friendly, non-toxic strategies for a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)-based high-performance OTE device by incorporating a nature-abundant material, vitamin C (VC), as an additive. We found that the intrinsic polar nature and reducing ability of VC induce synergy effects of microstructure alignment with PSS removal and dedoping of PEDOT, leading to simultaneous enhancement of the electrical conductivity (>400 S cm^-1) and the Seebeck coefficient (>30 μV K^-1) and a resultant high thermoelectric power factor of 51.8 μW m^-1 K^-2. In addition, inspired by the eco-friendly fabrication process, we further demonstrated a transient OTE device, which can be fully degraded with naturally occurring substances, by fabricating it on a bio-based cellulose acetate substrate. We believe that our eco-friendly strategies from fabrication to disposal of the OTE can be applied to the development of high-performance, wearable, and bio-compatible OTE devices with minimal waste and further trigger the research on genuinely green thermal energy harvesting.

Triggering ZT to 0.40 by Engineering Orientation in One Polymeric Semiconductor

Breaking the thermoelectric (TE) trade-off relationship is an important task for maximizing the TE performance of polymeric semiconductors. Existing efforts have focused on designing high-mobility semiconductors and achieving ordered molecular doping, ignoring the critical role of the molecular orientation during TE conversion. Herein, the achievement of ZT to 0.40 is reported by fine-tuning the molecular orientation of one diketopyrrolopyrrole (DPP)-based polymer (DPP-BTz). Films with bimodal molecular orientation yield superior doping efficiency by increasing the lamellar spacing and achieve increased splitting between the Fermi energy and the transport energy to enhance the thermopower. These factors contribute to the simultaneous improvement in the Seebeck coefficient and electrical conductivity in an unexpected manner. Importantly, the bimodal film exhibits a maximum power factor of up to 346 µW m^-1 K^-2 , >400% higher than that of unimodal films. These results demonstrate the great potential of molecular orientation engineering in polymeric semiconductors for developing state-of-the-art organic TE (OTE) materials.

Extremely Suppressed Energetic Disorder in a Chemically Doped Conjugated Polymer

Chemical doping can be used to tune the optoelectronic properties of conjugated polymers (CPs), extending their applications as conducting materials. Unfortunately, chemically doped CP films containing excess dopants exhibit an increase in energetic disorder upon structural alteration, and Coulomb interactions between charge carriers and dopants also affect such disorder. The increase in energetic disorder leads to a broadening of the density of states, which consequently impedes efficient charge transport in chemically doped CPs. However, the molecular origins that are inherently resistant to such incidental increase of energetic disorder in chemically doped CPs have not been sufficiently explored. Here, it is discovered that energetic disorder in chemically doped CPs can be suppressed to a level close to the theoretical limit. Indacenodithiophene-co-benzothiadiazole (IDTBT) doped with triethyloxonium hexachloroantimonate (OA) exhibits disorder-free charge-transport characteristics and band-like transport behavior with astonishing carrier mobility as a result of reinforced 1D intramolecular transport. Molecular structure of IDTBT provides a capability to lower the energetic disorder that generally arises from the inclusion of heterogeneous dopants. The results suggest the possibilities of implementing disorder-free CPs that exhibit excellent charge transport characteristics in the chemically doped state and satisfy a prerequisite for their availability in the industry.

Morphological Ordering of the Organic Layer for High-Performance Hybrid Thermoelectrics

Inorganic-organic hybrids, such as Te-PEDOT:PSS core/shell nanowires, have emerged as a class of promising thermoelectric materials with combined attributes of mechanical flexibility and low cost. However, the poorly understood structure-property relationship calls for further investigation for performance enhancement. Here, through precise treatments of focused electron beam irradiation and thermal annealing on individual Te-PEDOT:PSS nanowires, new, nonchemical mechanisms are introduced to specifically engineer the organic phase, and the measured results provide an unprecedented piece of evidence, confirming the dominant role of organic shell in charge transport. Paired with the Kang-Snyder model and molecular dynamics simulations, this work provides mechanistic insights in terms of heating-enabled morphological ordering of the polymer chains. The measured results show that thermal annealing on the 42 nm nanowire results in a ZT value of 0.78 at 450 K. Through leveraging the interfacial self-assembly of the organic phase to construct a high electrical conductivity domain, this work lays out a clear framework for the development of next-generation soft thermoelectrics.

Polymer Gel with Tunable Conductive Properties: A Material for Thermal Energy Harvesting

The spontaneous gelation of poly(4-vinyl pyridine)/pyridine solution produces materials with conductive properties that are suitable for various energy conversion technologies. The gel is a thermoelectric material with a conductivity of 2.2-5.0 × 10^-6 S m^-1 and dielectric constant ε = 11.3. On the molecular scale, the gel contains various types of hydrogen bonding, which are formed via self-protonation of the pyridine side chains. Our measurements and calculations revealed that the gelation process produces bias-dependent polymer complexes: quasi-symmetric, strongly hydrogen-bonded species, and weakly bound protonated structures. Under an applied DC bias, the gelled complexes differ in their capacitance/conductive characteristics. In this work, we exploited the bias-responsive characteristics of poly(4-vinyl pyridine) gelled complexes to develop a prototype of a thermal energy harvesting device. The measured device efficiency is S = ΔV/ΔT = 0.18 mV/K within the temperature range of 296-360 K. Investigation of the mechanism underlying the conversion of thermal energy into electric charge showed that the heat-controlled proton diffusion (the Soret effect) produces thermogalvanic redox reactions of hydrogen ions on the anode. The charge can be stored in an external capacitor for heat energy harvesting. These results advance our understanding of the molecular mechanisms underlying thermal energy conversion in the poly(4-vinyl pyridine)/pyridine gel. A device prototype, enabling thermal energy harvesting, successfully demonstrates a simple path toward the development of inexpensive, low-energy thermoelectric generators.

Thermoelectric-Powered Sensors for Internet of Things

The Internet of Things (IoT) combines various sensors and the internet to form an expanded network, realizing the interconnection between human beings and machines anytime and anywhere. Nevertheless, the problem of energy supply limits the large-scale implementation of the IoT. Fortunately, thermoelectric generators (TEGs), which can directly convert thermal gradients into electricity, have attracted extensive attention in the IoT field due to their unique benefits, such as small sizes, long maintenance cycles, high stability, and no noise. Therefore, it is vital to integrate the significantly advanced research on TEGs into IoT. In this review, we first outline the basic principle of the thermoelectricity effect and summarize the common preparation methods for thermoelectric functional parts in TEGs. Then, we elaborate on the application of TEG-powered sensors in the human body, including wearable and implantable medical electronic devices. This is followed by a discussion on the application of scene sensors for IoTs, for example, building energy management and airliners. Finally, we provide a further outlook on the current challenges and opportunities.

Abnormal Seebeck Effect in Vertically Stacked 2D/2D PtSe2 /PtSe2 Homostructure

When a thermoelectric (TE) material is deposited with a secondary TE material, the total Seebeck coefficient of the stacked layer is generally represented by a parallel conductor model. Accordingly, when TE material layers of the same thickness are stacked vertically, the total Seebeck coefficient in the transverse direction may change in a single layer. Here, an abnormal Seebeck effect in a stacked two-dimensional (2D) PtSe₂ /PtSe₂ homostructure film, i.e., an extra in-plane Seebeck voltage is produced by wet-transfer stacking at the interface between the PtSe₂ layers under a transverse temperature gradient is reported. This abnormal Seebeck effect is referred to as the interfacial Seebeck effect in stacked PtSe₂ /PtSe₂ homostructures. This effect is attributed to the carrier-interface interaction, and has independent characteristics in relation to carrier concentration. It is confirmed that the in-plane Seebeck coefficient increases as the number of stacked PtSe₂ layers increase and observed a high Seebeck coefficient exceeding ≈188 µV K^-1 at 300 K in a four-layer-stacked PtSe₂ /PtSe₂ homostructure.

From Brittle to Ductile: A Scalable and Tailorable All-Inorganic Semiconductor Foil through a Rolling Process toward Flexible Thermoelectric Modules

Inorganic thermoelectric (TE) materials with outstanding capacity for energy conversion are expected to be promising eco-friendly and renewable power sources, but they are always intrinsically brittle, restricting their development in flexible TE electronics. Therefore, we have developed a facile manufacturing method of large-scale all-inorganic silver chalcogenide foils and flexible TE generators in this work. A rolling process, as an effective and facile molding technique, is applied in ductile TE materials. The figure-of-merit for flexibility of this free-standing foil is in the range of 0.02-0.13, suggesting the superior flexibility of the all-inorganic TE foils. A high TE figure-of-merit ZT of 0.47 at room temperature is reached for Ag₂S_0.45Se_0.45Te_0.1, which is one of the most promising room-temperature ZTs among flexible TE materials. A proof-of-concept flexible TE generator based on silver chalcogenide foils achieves an open-circuit voltage of 1.19 mV and an output power density of 1.8 mW/m² with a temperature difference of 2.7 °C across the TE leg, showing great potential in heat-to-electricity conversion.

Hybrid Photovoltaic/Thermoelectric Systems for Round-the-Clock Energy Harvesting

Due to their emission-free operation and high efficiency, photovoltaic cells (PVCs) have been one of the candidates for next-generation “green” power generators. However, PVCs require prolonged exposure to sunlight to work, resulting in elevated temperatures and worsened performances. To overcome this shortcoming, photovoltaic–thermal collector (PVT) systems are used to cool down PVCs, leaving the waste heat unrecovered. Fortunately, the development of thermoelectric generators (TEGs) provides a way to directly convert temperature gradients into electricity. The PVC–TEG hybrid system not only solves the problem of overheated solar cells but also improves the overall power output. In this review, we first discuss the basic principle of PVCs and TEGs, as well as the principle and basic configuration of the hybrid system. Then, the optimization of the hybrid system, including internal and external aspects, is elaborated. Furthermore, we compare the economic evaluation and power output of PVC and hybrid systems. Finally, a further outlook on the hybrid system is offered.