Zirconia in biomedical applications

Clinical effectiveness of Zirconia versus titanium dental implants in anterior region: an overview of systematic reviews

BACKGROUND

Nowadays dental implants are commonly used and to fulfil esthetic demands, zirconia has been suggested as an implant material as an alternative to titanium. Many researchers and systematic reviews are documented on it, but the results have been often inconsistent. This overview of systematic reviews aimed to report on the factors that influence the clinical effectiveness of zirconia (Zi) versus titanium (Ti) dental implants in anterior region.

METHODS

This overview of systematic reviews (Registration Number CRD42023396206) is in accordance with the Transparent Reporting of Systematic Reviews and Meta-analyses. PubMed, Cochrane, Scopus, Embase and Google Scholar databases were sourced for systematic review and meta-analyses. Joanna Briggs Institute (JBI) criteria and Measurement Tool to Assess systematic Reviews" (AMSTAR-2), evaluated the quality. The PICO-focused question of this overview of systematic reviews was "What are the various factors influencing the clinical performance of Zi versus Ti implants in the anterior area?", Evaluations were assessed by two assessors. In case there was any uncertainty or dispute among the reviewers, the work was included for further screening. Using Cohen's kappa, the inter-reviewer reliability was evaluated.

RESULTS

Six reviews were chosen from 57 suitable reviews for this data analysis. Although the survival and effectiveness rates backed titanium implants, there was no conclusive proof of marginal bone loss. Zirconium implants performed better in terms of aesthetics.

CONCLUSION

Clinical performance of zirconia could be considered at par with titanium implants in the anterior area. Titanium has exhibited greater mechanical performance but no significant difference between two recorded. In future, studies with improved design are needed to identify biological and technical factors that affect implant's efficacy.

NOVELTY AND RELEVANCE

This is the first overview of systematic reviews focusing specifically on the anterior region, evaluates both aesthetic and biomechanical performance of Zi and Ti Implants, offers detailed insight into material-specific advantages and limitations. In the present clinical scenario it addresses a critical gap by comparing the performance of Zi and Ti implants and evaluates patient-centred priorities, particularly in the highly visible anterior region.

A rapid and efficient zirconia bead-mediated ultrasonic strategy for DNA fragmentation up to 10 kbp

Single-molecule sequencing (SMS), a long-read DNA sequencing technology, plays a crucial role in genomics research. However, traditional ultrasonic shearing techniques struggle to efficiently produce DNA fragments ≥10 kbp, limiting the efficiency of SMS library preparation. Here, we developed a zirconia bead-mediated ultrasonic shearing method that enables precise DNA fragmentation through zirconia bead mechanical agitation induced by sonication cavitation. By optimizing parameters such as zirconia bead size, quantity, ultrasonic probe distance, ultrasonic time, water bath temperature, DNA sample volume, and DNA concentration, we obtained target fragments in the 10-20 kbp range. The results demonstrated that this method sheared purified λDNA (48.5 kbp) into fragments averaging 15 kbp within 20 seconds, achieving performance comparable to commercial g-TUBE methods. The method was also successfully applied to human genomic DNA. This simple, rapid and reliable DNA fragmentation method provides an effective solution for SMS library preparation with great potential for molecular detection and diagnostic applications.

Mechanical and biocompatibility testing of zirconia and lithium disilicate ceramics: An in vitro study

STATEMENT OF PROBLEM

High-translucency zirconia and lithium disilicate are among the most used materials in contemporary fixed prosthodontics because of their excellent esthetic and mechanical properties. However, their different cementation techniques, physical properties, and biocompatibility profiles can influence the clinician's choice.

PURPOSE

The purpose of this in vitro study was to evaluate the mechanical strength and adhesive cementation techniques for zirconia and lithium disilicate materials through mechanical testing, including compressive and pull-out tests. The biocompatibility of these materials was also assessed.

MATERIAL AND METHODS

A total of 72 human maxillary molars that were free from damage were embedded in acrylic resin and prepared 1 mm occlusal to the enamel-cementum junction. The specimens were divided into 3 groups: lithium disilicate (CAD), zirconia High-Translucency HT (CAD), and lithium disilicate (PRESS). Following the recommended cementation protocols, compression and pull-out tests were performed. Twelve disks of each group were fabricated to test the integration of gingival fibroblasts. Human gingival fibroblasts were isolated from gingival biopsies and cultured in Dulbecco modified Eagle medium (DMEM). Cell viability was determined using the 3-(4,5-di-methylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, serving as an indicator of cellular respiration.

RESULTS

Zirconia was the most mechanically efficient material, with a high resistance value (2081.4 ±405.4 N). The pull-out test determined that CAD-CAM lithium disilicate had similar adhesive cementation strength (244.3 ±29.3 N) to the other groups. In terms of biocompatibility, all materials demonstrated good results, with lithium disilicate CAD emerging as the most biocompatible material. Statistically significant differences were observed between the zirconia HT material and lithium disilicate PRESS (P=.006) and between lithium disilicate CAD and lithium disilicate PRESS (P=.002).

CONCLUSIONS

All the monolithic restorations analyzed have shown excellent results in terms of mechanical properties, adhesion, and biocompatibility. Zirconia exhibited outstanding mechanical properties, making it an ideal choice for applications requiring high strength. To achieve adhesion results comparable with those of lithium disilicate, a protocol using airborne-particle abrasion and silane with 10-MDP is recommended. This approach ensures optimal adhesion, enhancing the longevity and effectiveness of the restoration.

Comparison of clinical outcomes between single metal-ceramic and zirconia crowns

STATEMENT OF PROBLEM

Evidence comparing the survival of zirconia crowns with metal-ceramic crowns is sparse. Knowledge of their survival and a comparison of their clinical outcomes would improve clinical decision making.

PURPOSE

The purpose of this university-based study was to compare the survival, failures, biological and technical complications encountered with zirconia and metal-ceramic crowns restored and followed up over a similar period.

MATERIAL AND METHODS

This retrospective chart review consisted of 403 patients treated at the University of Toronto, Faculty of Dentistry, predoctoral dental clinic in whom zirconia (n=209) and metal-ceramic (n=306) crowns were inserted between September 2015 and July 2016 and followed for up to 7 years. Outcome measures included failure, causes for failure, and complications associated with survival. Inferential statistical analysis included the chi-squared test, t test, Mann-Whitney test, Bonferroni-adjusted z-test, Kaplan-Meier survival test, and logistic regression to examine differences between crown types and explore crown failures (α=.05).

RESULTS

The mean follow-up period was 3.00 years (median 2.58 years). Forty-one (8.0%) crowns had no follow-up, with no difference in follow-up between crown type: metal-ceramic n=23(7.5%), zirconia n=18(8.6%), χ²(1)=0.20, P=.652). Excluding those with no follow-up, the follow-up time between metal-ceramic (mean=3.07, median=2.58) and zirconia (mean=3.54, median=3.32) crowns was statistically similar (P=.052). There were 62 anterior crowns (12.0%) and 453 posterior crowns (88.0%), χ²(1)=22.40, P<.001, with no difference between groups. Overall, 44 crowns (8.5%) failed, 30 (9.8%) metal-ceramic and 14 (6.7%) zirconia, with no statistical difference in proportion of failed crowns between groups (χ²(1)=1.53, P=.216). There were 35 crowns with biological failures (6.8%), 26 (8.5%) in the metal-ceramic and 9 (4.4%) in the zirconia group, with no statistical difference between groups (χ²(1)=3.33, P=.068). Nine crowns had technical failures (1.7%), 4 (1.4%) in the metal-ceramic group and 5 (2.5%) in the zirconia group, with no statistical difference between groups (χ²(1)=0.73, P=.394). Biological (79.5%) rather than technical complications were found to be the most frequent cause of failure, goodness-of-fit χ²(1)=15.36, P<.001. Tooth fracture (50.0%) specifically was found to be the most frequent cause of failure, χ²(3)=21.27, P<.001. The total number of crowns that survived was 471 (91.5%); 276 (90.1%) were metal-ceramic and 195(93.3%) zirconia. The survival time (years) for metal-ceramic was mean=6.26, 95% CI [6.01-6.51] and for zirconia crowns mean=6.54, 95% CI [6.31-6.77]. Of the crowns that survived, 370 (78.6%) had no clinical complications, and 101 (21.4%) crowns demonstrated similar clinical complications, with no statistical differences between groups.

CONCLUSIONS

Within the study follow-up time, the survival of monolithic zirconia and metal-ceramic crowns was 91.5%, with similar clinical complications between groups. Biological complications, especially tooth fracture, were a significantly more frequent complication with both types of crowns.

Gallium-doped zirconia coatings modulate microbiological outcomes in dental implant surfaces

Despite the significant recent advances in manufacturing materials supporting advanced dental therapies, peri-implantitis still represents a severe complication in dental implantology. Herein, a sol-gel process is proposed to easily deposit antibacterial zirconia coatings onto bulk zirconia, material, which is becoming very popular for the manufacturing of abutments. The coatings' physicochemical properties were analyzed through x-ray diffraction and scanning electron microscopy-energy-dispersive x-ray spectroscopy investigations, while their stability and wettability were assessed by microscratch testing and static contact angle measurements. Uniform gallium-doped tetragonal zirconia coatings were obtained, featuring optimal mechanical stability and a hydrophilic behavior. The biological investigations pointed out that gallium-doped zirconia coatings: (i) displayed full cytocompatibility toward human gingival fibroblasts; (ii) exhibited significant antimicrobial activity against the Aggregatibacter actinomycetemcomitans pathogen; (iii) were able to preserve the commensal Streptococcus salivarius. Furthermore, the proteomic analyses revealed that the presence of Ga did not impair the normal oral microbiota. Still, interestingly, it decreased by 17% the presence of Fusobacterium nucleatum, a gram-negative, strictly anaerobic bacteria that is naturally present in the gastrointestinal tract. Therefore, this work can provide a valuable starting point for the development of coatings aimed at easily improving zirconia dental implants' performance.

In vitro and in vivo evaluation of the osseointegration capacity of a polycarbonate-urethane zirconium-oxide composite material for application in a focal knee resurfacing implant

Currently available focal knee resurfacing implants (FKRIs) are fully or partially composed of metals, which show a large disparity in elastic modulus relative to bone and cartilage tissue. Although titanium is known for its excellent osseointegration, the application in FKRIs can lead to potential stress-shielding and metal implants can cause degeneration of the opposing articulating cartilage due to the high resulting contact stresses. Furthermore, metal implants do not allow for follow-up using magnetic resonance imaging (MRI).To overcome the drawbacks of using metal based FKRIs, a biomimetic and MRI compatible bi-layered non-resorbable thermoplastic polycarbonate-urethane (PCU)-based FKRI was developed. The objective of this preclinical study was to evaluate the mechanical properties, biocompatibility and osteoconduction of a novel Bionate® 75D - zirconium oxide (B75D-ZrO2) composite material in vitro and the osseointegration of a B75D-ZrO2 composite stem PCU implant in a caprine animal model. The tensile strength and elastic modulus of the B75D-ZrO2 composite were characterized through in vitro mechanical tests under ambient and physiological conditions. In vitro biocompatibility and osteoconductivity were evaluated by exposing human mesenchymal stem cells to the B75D-ZrO2 composite and culturing the cells under osteogenic conditions. Cell activity and mineralization were assessed and compared to Bionate® 75D (B75D) and titanium disks. The in vivo osseointegration of implants containing a B75D-ZrO2 stem was compared to implants with a B75D stem and titanium stem in a caprine large animal model. After a follow-up of 6 months, bone histomorphometry was performed to assess the bone-to-implant contact area (BIC). Mechanical testing showed that the B75D-ZrO2 composite material possesses an elastic modulus in the range of the elastic modulus reported for trabecular bone. The B75D-ZrO2 composite material facilitated cell mediated mineralization to a comparable extent as titanium. A significantly higher bone-to-implant contact (BIC) score was observed in the B75D-ZrO2 implants compared to the B75D implants. The BIC of B75D-ZrO2 implants was not significantly different compared to titanium implants. A biocompatible B75D-ZrO2 composite approximating the elastic modulus of trabecular bone was developed by compounding B75D with zirconium oxide. In vivo evaluation showed an significant increase of osseointegration for B75D-ZrO2 composite stem implants compared to B75D polymer stem PCU implants. The osseointegration of B75D-ZrO2 composite stem PCU implants was not significantly different in comparison to analogous titanium stem metal implants.

Evaluating mechanical and surface properties of zirconia-containing composites: 3D printing, subtractive, and layering techniques

This study assessed the monotonic and fatigue flexural strength (FS), elastic modulus (E), and surface characteristics of a 3D printed zirconia-containing resin composite compared to subtractive and conventional layering methods. Specimens, including discs (n = 15; Ø = 15 mm × 1.2 mm) and bars (n = 15; 14 × 4 × 1.2 mm), were prepared and categorized into three groups: 3D printing (3D printing - PriZma 3D Bio Crown, Makertech), Subtractive (Lava Ultimate blocks, 3M), and Layering (Filtek Z350 XT, 3M). Monotonic tests were performed on the discs using a piston-on-three-balls setup, while fatigue tests employed similar parameters with a frequency of 10 Hz, initial stress at 20 MPa, and stress increments every 5000 cycles. The E was determined through three-point-bending test using bars. Surface roughness, fractographic, and topographic analyses were conducted. Statistical analyses included One-way ANOVA for monotonic FS and roughness, Kruskal-Wallis for E, and Kaplan-Meier with post-hoc Mantel-Cox and Weibull analysis for fatigue strength. Results revealed higher monotonic strength in the Subtractive group compared to 3D printing (p = 0.02) and Layering (p = 0.04), while 3D Printing and Layering exhibited similarities (p = 0.88). Fatigue data indicated significant differences across all groups (3D Printing < Layering < Subtractive; p = 0.00 and p = 0.04, respectively). Mechanical reliability was comparable across groups. 3D printing and Subtractive demonstrated similar E, both surpassing Layering. Moreover, 3D printing exhibited higher surface roughness than Subtractive and Layering (p < 0.05). Fractographic analysis indicated that fractures initiated at surface defects located in the area subjected to tensile stress concentration. A porous surface was observed in the 3D Printing group and a more compact surface in Subtractive and Layering methods. This study distinguishes the unique properties of 3D printed resin when compared to conventional layering and subtractive methods for resin-based materials. 3D printed shows comparable monotonic strength to layering but lags behind in fatigue strength, with subtractive resin demonstrating superior performance. Both 3D printed and subtractive exhibit similar elastic moduli, surpassing layering. However, 3D printed resin displays higher surface roughness compared to subtractive and layering methods. The study suggests a need for improvement in the mechanical performance of 3D printed material.

Enhancement of Biocompatibility of High-Transparency Zirconia Abutments with Human Gingival Fibroblasts via Cold Atmospheric Plasma Treatment: An In Vitro Study

The objective of this study was to explore the effects of cold atmospheric plasma (CAP) treatment on the biological behavior of human gingival fibroblasts (HGFs) cultured on the surface of high-transparency zirconia. Two types of zirconia, 3Y-ZTP and 4Y-PSZ, were subjected to a CAP treatment for various treatment durations. Analyses of the physical and chemical properties of 3Y-ZTP and 4Y-PSZ were conducted using scanning electron microscopy, contact angle measurements, and X-ray photoelectron spectroscopy, both before and after CAP treatment. The biological responses of HGFs on both surfaces were assessed using CCK-8 assay, confocal laser scanning microscopy, and real-time PCR. Initially, the oxygen and hydroxyl contents on the surface of 4Y-PSZ exceeded those on 3Y-ZTP. CAP treatment enhanced the surface hydrophilicity and the reactive oxygen species (ROS) content of 4Y-PSZ, while not altering the surface morphology. After CAP treatment, HGFs' adhesion on 4Y-PSZ was superior, with more pronounced effects compared to 3Y-ZTP. Notably, HGFs counts and the expression of adhesion-related genes on 4Y-PSZ peaked following the CAP exposures for 30 s and 60 s. Consequently, this study demonstrates that, following identical CAP treatments, 4Y-PSZ is more effective in promoting HGFs adhesion compared to traditional 3Y-ZTP zirconia.

Advances in ceramics for tooth repair: From bench to chairside

OBJECTIVES

To give a comprehensive review of advancement in dental ceramics, fabrication methods, and the challenges associated with clinical application.

DATA, SOURCES AND STUDY SELECTION

Researches on chemical composition, biomechanical behaviors, optical properties, bonding strategies and fabrication methods were included. The search of articles was independently conducted by two authors in the PubMed, Scopus, Medline and Web of Science.

CONCLUSIONS

Dental ceramics have shown significant advancements in terms of esthetics and function. However, improving fracture toughness without compromising optical properties remains a challenge. Repairing fractured zirconia or glass-matrix ceramic prostheses with the same material is difficult due to the sintering process. Developing innovative bonding techniques that provide strong and long-lasting bonding strength between ceramics and tooth structures poses a recurring obstacle.

CLINICAL SIGNIFICANCE

Despite the emergence of dental ceramics and fabrication techniques, certain limitations such as susceptibility to brittleness and fracture still exist. Therefore, the current review provided valuable information around the advanced dental ceramics in tooth repair. The laboratory test data and the clinical outcome are also presented in details, aiming to guide clinicians in making informed decisions regarding ceramic restorations.

3D printed, subtractive, and conventional acrylic resins: Evaluation of monotonic versus fatigue behavior and surface characteristics

This study assessed the mechanical properties and surface characteristics of dental prosthetic acrylic resin fabricated by 3D printing, comparing it with subtractive, pressing, and molding techniques. Bar-shaped specimens (N= 90; 65 × 10 × 3.3 mm; ISO:207951) were prepared and assigned into six groups: PRINT (3D printing vis stereolithography with PriZma 3D Bio Denture, Makertech Labs); SUB (subtractive manufacturing with Vipiblock Trilux, Vipi); PRESS Base (pressing using muffle with Thermo Vipi Wave, Vipi for base); PRESS Tooth (pressing with Onda-cryl, Clássico for tooth); MOLD Base (molding using addition silicone with Vipi Flash, Vipi for base); and MOLD Tooth (molding with Dencor, Clássico for tooth). Monotonic flexural strength (FS) and elastic modulus (E) were measured using a three-point bending approach (n= 5) on a universal testing machine at a crosshead speed of 5 mm/min. Fatigue testing (n= 10) followed similar geometry and settings, with a frequency of 2 Hz, initial stress level at 20 MPa, and stress increments of 5 MPa every 2,500 cycles. Surface roughness (n= 10) was assessed through profilometry, and fractographic and topographic analyses were conducted. Statistical analyses included One-Way ANOVA for monotonic FS, roughness, and E, along with Kaplan-Meier with Mantel-Cox post-hoc and Weibull analysis for fatigue strength. PRINT showed lower monotonic FS than the SUB and PRESS Tooth but comparable fatigue strength to these groups and superior to PRESS Base and MOLD (Base and Tooth) groups. All groups had similar Weibull moduli. Surface roughness of the PRINT group was comparable to most techniques but higher than the PRESS Tooth group. Fractographic analysis revealed fractures originating from surface defects under tensile stress, with SEM showing scratch patterns in all groups except PRINT, which had a more uniform surface. Despite its lower monotonic strength, 3D printed resin demonstrated comparable fatigue strength to subtractive and pressing methods and similar surface roughness to most methods, indicating its potential as a viable option for dental prosthesis.

Fifteen-year recall period on zirconia-based single crowns and fixed dental prostheses. A prospective observational study

AIM

The aim of this study was to evaluate the long-term clinical outcomes of zirconia-based prostheses used for tooth-supported or implant-supported single crowns and fixed dental prostheses (FPD).

METHODS

The authors conducted a prospective analysis of 562 zirconia core restorations supported by endodontically treated teeth or titanium implant in 276 patients in a general dental private practice, with a follow-up period of 15 years. The study was stopped after patients achieved 15 yrs of follow-up. The study analyzed the failure and complication rates of single and multiple crowns, based on Kaplan Meier analysis.

RESULTS

During follow-up period, there were 26 complications and 156 failures. The crown level analysis revealed a cumulative failure rate of 28.33% and complication rate of 8.47% for zirconia crowns after 15 years. The complication rate was found to be higher for titanium implant-supported than for natural teeth-supported crowns. The different types of crown-based failure include: veener fracture 5.01% (N = 29), metal zirconia led to 14.85% (N = 86) loss of retention, and 1.73% (N = 10) loss of crown due to extraction.

CONCLUSION

Based on these findings, zirconia core restorations appear to be a reliable long-term solution for crowns and fixed dental prostheses.

CLINICAL RELEVANCE

The study suggests that zirconia restorations can be successfully used for long-term prostheses on natural teeth or implants supported. The study results provide clinicians valuable information when selecting prosthetic restorations material.

Optical properties of recycled zirconia for dental applications

STATEMENT OF PROBLEM

While waste zirconia can be recycled, whether the optical properties of recycled zirconia match those of commercially available zirconia is unclear.

PURPOSE

The purpose of this in vitro study was to evaluate the optical properties of recycled zirconia by assessing its color, translucency, and opalescence across different thicknesses and shades.

MATERIAL AND METHODS

Sixty specimens were prepared from 3 mol% yttria-stabilized tetragonal zirconia polycrystal blocks (Lava Plus; 3M ESPE) (group C); 60 other specimens were prepared from waste blocks of the same zirconia (group R). The specimens were further categorized into 4 subgroups (n=15) based on their thicknesses (1.0 mm or 1.5 mm) and shades (A1 or A3). Specimen color was measured with a spectrophotometer (Easyshade Advance 4.0; Vita ZahnFabrik). The parameters of color difference (ΔE00), translucency (TP), contrast ratio (CR), and opalescence (OP) were calculated. Grain size analysis was performed using scanning electron microscopy. Data were analyzed with analysis of variance (ANOVA) (α=.05).

RESULTS

Significant differences in translucency and opalescence were observed between groups C and R in all specimens (P<.001). Group R exhibited a range of TP (4.89 to 11.27), CR (0.74 to 0.91), and OP (3.36 to 8.65) values. The ΔE00 values between groups C and R ranged from 13.99 to 21.31. Both thickness and shade significantly affected the ΔE00 values (P<.001). The grain size in group C was not significantly different from that in group R (F=0.364, df=1, P=.555). The TP and OP values of group R decreased with increasing thickness (P<.001).

CONCLUSIONS

Recycled zirconia was less translucent and opalescent than commercially available zirconia. The color difference between commercially available and recycled zirconia exceeded the acceptable threshold, even when using the same staining procedure. Recycled zirconia exhibited reduced translucency and opalescence with increasing thickness.

Quantum mechanical analysis of yttrium-stabilized zirconia and alumina: implications for mechanical performance of esthetic crowns

BACKGROUND

Yttrium-stabilized zirconia (YSZ) and alumina are the most commonly used dental esthetic crown materials. This study aimed to provide detailed information on the comparison between yttrium-stabilized zirconia (YSZ) and alumina, the two materials most often used for esthetic crowns in dentistry.

METHODOLOGY

The ground-state energy of the materials was calculated using the Cambridge Serial Total Energy Package (CASTEP) code, which employs a first-principles method based on density functional theory (DFT). The electronic exchange-correlation energy was evaluated using the generalized gradient approximation (GGA) within the Perdew (Burke) Ernzerhof scheme.

RESULTS

Optimization of the geometries and investigation of the optical properties, dynamic stability, band structures, refractive indices, and mechanical properties of these materials contribute to a holistic understanding of these materials. Geometric optimization of YSZ provides important insights into its dynamic stability based on observations of its crystal structure and polyhedral geometry, which show stable configurations. Alumina exhibits a distinctive charge, kinetic, and potential (CKP) geometry, which contributes to its interesting structural framework and molecular-level stability. The optical properties of alumina were evaluated using pseudo-atomic computations, demonstrating its responsiveness to external stimuli. The refractive indices, reflectance, and dielectric functions indicate that the transmission of light by alumina depends on numerous factors that are essential for the optical performance of alumina as a material for esthetic crowns. The band structures of both the materials were explored, and the band gap of alumina was determined to be 5.853 eV. In addition, the band structure describes electronic transitions that influence the conductivity and optical properties of a material. The stability of alumina can be deduced from its bandgap, an essential property that determines its use as a dental material. Refractive indices are vital optical properties of esthetic crown materials. Therefore, the ability to understand their refractive-index graphs explains their transparency and color distortion through how the material responds to light..The regulated absorption characteristics exhibited by YSZ render it a highly attractive option for the development of esthetic crowns, as it guarantees minimal color distortion.

CONCLUSION

The acceptability of materials for esthetic crowns is strongly determined by mechanical properties such as elastic stiffness constants, Young's modulus, and shear modulus. YSZ is a highly durable material for dental applications, owing to its superior mechanical strength.

Biological Properties of 3D-Printed Zirconia Implants with p-Cell Structures

Research on 3-dimensional (3D) printed porous zirconia-based dental implants is still in its infancy. This study aimed to evaluate the biological responses of novel zirconia implants with p-cell structures fabricated by 3D printing. The solid zirconia samples exhibited comparable density, 3-point flexural strength, and accelerated aging properties compared to specimens prepared previously by conventional methods. Cell-based experiments showed that the p-cell structure promoted cell proliferation, adhesion, and osteogenesis-related protein expression. Mechanical tests showed that both p-cell and control implants could withstand a torque of 35 Ncm without breaking. The mean maximum breaking loads of p-cell and control implants were 1,222.429 ± 115.591 N and 1,903.857 ± 250.673 N, respectively, which were much higher than the human physiological chewing force and human mean maximum occlusal force. An animal experiment showed that the bone trabeculae around the implants were significantly thicker, more numerous, and denser in the p-cell group than in the control group. This work could provide promising guidance for further exploring 3D printing techniques for porous zirconia bionic implants in dentistry.

Topographical and crystalline change on surface by sandblasting improve flexural and shear bond strength of niobia-modified yttria-stabilized tetragonal zirconia polycrystal

This study aimed to investigate the effects of sandblasting on the physical properties and bond strength of two types of translucent zirconia: niobium-oxide-containing yttria-stabilized tetragonal zirconia polycrystals ((Y, Nb)-TZP) and 5 mol% yttria-partially stabilized zirconia (5Y-PSZ). Fully sintered disc specimens were either sandblasted with 125 µm alumina particles or left as-sintered. Surface roughness, crystal phase compositions, and surface morphology were explored. Biaxial flexural strength (n=10) and shear bond strength (SBS) (n=12) were evaluated, including thermocycling conditions. Results indicated a decrease in flexural strength of 5Y-PSZ from 601 to 303 MPa upon sandblasting, while (Y, Nb)-TZP improved from 458 to 544 MPa. Both materials significantly increased SBS after sandblasting (p<0.001). After thermocycling, (Y, Nb)-TZP maintained superior SBS (14.3 MPa) compared to 5Y-PSZ (11.3 MPa) (p<0.001). The study concludes that (Y, Nb)-TZP is preferable for sandblasting applications, particularly for achieving durable bonding without compromising flexural strength.

Comparative analysis of intaglio surface trueness of cement-retained implant-supported prostheses generated by a cast-free digital workflow and a three-dimensionally printed cast workflow

STATEMENT OF PROBLEM

Comparative analysis of the accuracy of the prostheses produced by a cast-free digital workflow and 3-dimensional (3D) printing cast workflow is lacking.

PURPOSE

The purpose of the present investigation was to compare the intaglio surface trueness of implant-supported prostheses fabricated by using 3 different digital workflows: cast-free computer-aided design (CAD), 3D printed cast CAD (direct insert), and 3D printed cast CAD (indirect insert).

MATERIAL AND METHODS

The laboratory data of 11 partially edentulous arches for prosthetic implant treatment were obtained. Three different workflows were tested to produce the cement-retained prostheses: cast-free CAD (Group CF), 3D printed cast CAD with direct insert (Group PD), and 3D printed cast CAD with indirect insert (Group PI). The intaglio surfaces of the prosthesis CAD data from Groups CF, PD, and PI were superimposed with 3D printed prosthesis scan data from Group CF to measure 3D surface deviation. Using the prosthesis CAD data from Group CF as a reference, those from Groups PD and PI were compared by superimposition analysis. The root mean square (RMS) estimates, positive average deviations, and negative average deviations were measured. The Kruskal-Wallis test and Dunn test with Bonferroni correction, and the Wilcoxon rank sum test were used for statistical analyses (α=.05).

RESULTS

Significant differences were found among the 3 groups when the 3D printed prosthesis scan data were referenced (P<.05). Group CF showed the lowest RMS, positive average deviation, and negative deviation values, while Group PI showed the highest values. Significant differences in the RMS, positive average deviation, and negative average deviation values were found between Groups PD and PI when the prosthesis CAD data (Group CF) were referenced (P<.05).

CONCLUSIONS

Among the 3 different workflows tested, the prostheses generated from the cast-free CAD flow showed significantly lower intaglio surface deviation than those generated from the 3D printed cast CAD flows, regardless of the insertion method of the implant replicas.

Microstructure, physical and mechanical properties of dental polychromic multilayer zirconia of uniform composition

The present study aimed to compare the microstructure, physical, and mechanical properties of three commercially available dental polychromatic multilayer zirconia materials of uniform composition: Dima Mill Zirconia ML, VITA YZ/ST Multicolor, and VITA YZ/XT Multicolor (with 3, 4, and 5 mol% Y2 O3 , respectively); thus, the influence of Y2 O3 content on the above properties of the produced materials was experimentally studied. Homogeneous zirconia ceramics with a dense micro- and nanostructure, without pores or defects, were produced after milling the blocks and sintering, which resulted in yttrium-stabilized tetragonal and cubic zirconia. Statistical analysis of the results of measurable magnitudes was performed by the one-way ANOVA test. The increase of Y2 O3 content (from 3 to 5 mol%) favored larger grain and crystallite sizes and a decrease of the values of the mechanical properties; yet, the differences were statistically insignificant. Clinically, these differences are expected to have no impact on their function in the oral cavity, both in terms of their fracture propensity and the damage that can be caused to the opposing teeth. Accordingly, the experimental results qualify the polychromic multilayer zirconia ceramics of uniform composition fabricated by milling technology for use in dental restorations.

Natural medicine delivery from 3D printed bone substitutes

Unmet medical needs in treating critical-size bone defects have led to the development of numerous innovative bone tissue engineering implants. Although additive manufacturing allows flexible patient-specific treatments by modifying topological properties with various materials, the development of ideal bone implants that aid new tissue regeneration and reduce post-implantation bone disorders has been limited. Natural biomolecules are gaining the attention of the health industry due to their excellent safety profiles, providing equivalent or superior performances when compared to more expensive growth factors and synthetic drugs. Supplementing additive manufacturing with natural biomolecules enables the design of novel multifunctional bone implants that provide controlled biochemical delivery for bone tissue engineering applications. Controlled release of naturally derived biomolecules from a three-dimensional (3D) printed implant may improve implant-host tissue integration, new bone formation, bone healing, and blood vessel growth. The present review introduces us to the current progress and limitations of 3D printed bone implants with drug delivery capabilities, followed by an in-depth discussion on cutting-edge technologies for incorporating natural medicinal compounds embedded within the 3D printed scaffolds or on implant surfaces, highlighting their applications in several pre- and post-implantation bone-related disorders.

Longevity of extrinsic stains on monolithic zirconia restorations: An in vitro study

STATEMENT OF PROBLEM

Three-mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) has been commonly used for fixed prosthodontic restorations. The opacity of 3Y-TZP may be masked with external staining, although the longevity of extrinsic stains applied to monolithic zirconia is unclear.

PURPOSE

The purpose of this in vitro study was to analyze the color and surface roughness of extrinsically stained zirconia specimens after thermocycling and toothbrushing.

MATERIAL AND METHODS

Monolithic Ø12.5×1.25-mm zirconia disks were milled from 3Y-TZP blocks, sintered according to manufacturer instructions, and then divided into 3 groups (C, J, and O; n=16) for application of stain and glaze. All specimens underwent 10 000 thermocycles in distilled water before being further divided into 2 dentifrice groups (n=8): normal grit, low relative dentin abrasivity (RDA) (Subgroup N) and abrasive grit, high RDA (Subgroup A). Specimens were brushed in a multistation brushing machine under 1.47 N of force using a 5:8 toothpaste and distilled water slurry for 10 000 cycles with a straight (American Dental Association Standard) toothbrush to simulate 1 year of toothbrushing. Color and surface roughness measurements were obtained at 3 time points: baseline, after thermocycling, and after brushing. A 2-way repeated measures ANOVA was used to independently assess changes in color and surface roughness with respect to thermocycling and brushing (α=.05).

RESULTS

Group J displayed no significant change in color for either dentifrice system (P>.05). However, a significant change in surface roughness was observed for both dentifrice subgroups (P<.001). Group C specimens displayed significant changes in color (P<.001) and surface roughness (P<.001) for both dentifrice systems. Group O specimens displayed significant changes in color (P<.025) for both dentifrice systems and significant changes in surface roughness (P<.004) for subgroup A, but no significant changes for subgroup N (P=.075).

CONCLUSIONS

Artificial aging of monolithic zirconia resulted in changes in color and surface roughness that did not surpass the thresholds for perceptibility and acceptability. This study failed to establish durability limits for extrinsic stains applied to 3Y-TZP.

Head, acetabular liner composition, and rate of revision and wear in total hip arthroplasty: a Bayesian network meta-analysis

Total hip arthroplasty (THA) is a common procedure for patients suffering from hip pain e.g. from osteoarthritis, osteonecrosis, or hip fractures. The satisfaction of patients undergoing THA is influenced by the choice of implant type and material, with one key factor being the selection of the appropriate material combination for the bearing surface. In this Bayesian network meta-analysis, we investigated the impact of material combinations for the bearing surface on the longevity of hip implants. The wear penetration rate per year and the total wear penetration in the liner resulting from different material combinations, as well as the survival rate at last follow-up, were examined. We analyzed a total of 663,038 THAs, with 55% of patients being women. Mean patient age was 59.0 ± 8.1 years and mean BMI 27.6 ± 2.6 kg/m2. The combination of an aluminium oxide (Al2O3) head and an Al2O3 liner demonstrated the lowest wear penetration at last follow-up and the lowest rate of wear penetration per year. Additionally, the combination of a crosslinked polyethylene (XLPE) liner and a zircon oxide (ZrO2) head demonstrated the lowest rate of revision at last follow-up. These findings underscore the importance of careful material selection for hip implant bearing surfaces to optimize their longevity and patient satisfaction after THA.

Oxygen-Deficient Bioceramics: Combination of Diagnosis, Therapy, and Regeneration

The journey of ceramics in medicine has been synchronized with an evolution from the first generation-alumina, zirconia, etc.-to the third -3D scaffolds. There is an up-and-coming member called oxygen-deficient or colored bioceramics, which have recently found their way through biomedical applications. The oxygen vacancy steers the light absorption toward visible and near infrared regions, making the colored bioceramics multifunctional-therapeutic, diagnostic, and regenerative. Oxygen-deficient bioceramics are capable of turning light into heat and reactive oxygen species for photothermal and photodynamic therapies, respectively, and concomitantly yield infrared and photoacoustic images. Different types of oxygen-deficient bioceramics have been recently developed through various synthesis routes. Some of them like TiO2- x , MoO3- x , and WOx have been more investigated for biomedical applications, whereas the rest have yet to be scrutinized. The most prominent advantage of these bioceramics over the other biomaterials is their multifunctionality endowed with a change in the microstructure. There are some challenges ahead of this category discussed at the end of the present review. By shedding light on this recently born bioceramics subcategory, it is believed that the field will undergo a big step further as these platforms are naturally multifunctional.

In vitro comparative study between adhesion forces obtained on zirconia ceramic micromechanically treated with femtosecond laser (1027 nm), carbon dioxide laser (10,600 nm), and aluminum-oxide particles

Conventional surface roughening treatments used for silica-based ceramics in order to improve subsequent adhesion become unreliable for zirconia ceramics. Laser conditioning can be a good alternative. The purpose of this in vitro study was to compare conventional (macro) shear bond strength (SBS) values obtained between resin composite and zirconium oxide ceramic samples grouped according to different micromechanical treatments received, and examine differences in surface roughness. One-hundred and fifty disks of sintered zirconia were randomly divided into 5 groups and roughened as follows: (1) Group NOT, no surface treatment; (2) Group APA, abraded with 50-μm aluminum-oxide (Al2O3) particles; (3) Group TBS, abraded with 30-μm aluminum-oxide particles covered with silica; (4) Group CO2, irradiated with a CO2 laser which emitted in continuous wave mode at 3 W of power; and (5) Group FEM, irradiated with a pulsed femtosecond laser, with an incident energy of 10 μJ, a frequency of 1000 Hz, and a fluence of 1.3 kJ/cm2. All surfaces were treated with a MDP-containing adhesive/silane coupling agent mixture upon which were prepared and light polymerized composite resin cylinders. Shear bond strength was measured and samples were observed by scanning electron microscopy (SEM). Statistically significant differences (p < 0.05) were found among all groups, except between CO2 and FEM, which showed the highest adhesion values (15.12 ± 2.35 MPa and 16.03 ± 2.73 MPa). SEM revealed differences in surface patterns. CO2 laser irradiation can be an alternative to sandblasting, although it could also weaken the ceramic. Suitable surface patterns on zirconia ceramics can be obtained with ultrashort pulsed radiation emitted by a pulsed femtosecond laser.

Structure and Physical Properties of Ceramic Materials Based on ZrO2-Sc2O3 for SOFC Electrolytic Membranes Obtained from Powders of Melted Solid Solutions with a Similar Composition

This paper presents the results of studying the phase composition, luminescent characteristics, and ionic conductivity of ceramic scandium-stabilized solid solutions of zirconium dioxide containing 9 and 10 mol% Sc2O3. Ceramic samples were prepared by sintering powders obtained by grinding melted solid solutions of the same composition. A comparative analysis of the obtained data with similar characteristics of single crystals has been carried out. Differences in the phase composition of ceramics and initial single crystals were found. The effect of the structure and properties of grain boundaries on the ionic conductivity of ceramic samples is discussed. It is shown that the differences in the ionic conductivity of ceramic samples and crystals are mainly due to changes in the structure and phase composition.

Biomedical Applications of Zirconia-Based Nanomaterials: Challenges and Future Perspectives

ZrO₂ nanoparticles have received substantially increased attention in every field of life owing to their wide range of applications. Zirconium oxide is a commercially economical, non-hazardous, and sustainable metal oxide having diversified potential applications. ZrO₂ NPs play a vast role in the domain of medicine and pharmacy such as anticancer, antibacterial, and antioxidant agents and tissue engineering owing to their reliable curative biomedical applications. In this review article, we address all of the medical and biomedical applications of ZrO₂ NPs prepared through various approaches in a critical way. ZrO₂ is a bio-ceramic substance that has received increased attention in biomimetic scaffolds owing to its high mechanical strength, excellent biocompatibility, and high chemical stability. ZrO₂ NPs have demonstrated potential anticancer activity against various cancer cells. ZrO₂-based nanomaterials have exhibited potential antibacterial activity against various bacterial strains and have also demonstrated excellent antioxidant activity. The ZrO₂ nanocomposite also exhibits highly sensitive biosensing activity toward the sensing of glucose and other biological species.

Ultrashort pulse laser patterning of zirconia (3Y-TZP) for enhanced adhesion to resin-matrix cements used in dentistry: An integrative review

Surface modification of yttria-stabilized tetragonal zirconia polycrystals (Y-TZP) using lasers for adhesion enhancement with resin-matrix cement has been increasingly explored. However, Y-TZP is chemically inert and non-reactive, demanding surface modification using alternative approaches to enhance its bond strength to resin-matrix cements. The main aim of this study was to conduct an integrative review on the influence of ultrashort pulse laser patterning of zirconia (3Y-TZP) for enhanced bonding to resin-matrix cements. An electronic search was performed on web of science, SCOPUS, Pubmed/Medline, Google Scholar and EMBASE using a combination of the following search items: zirconia, 3Y-TZP, surface modification, laser surface treatment, AND laser, ultrashortpulse laser, bonding, adhesion, and resin cement. Articles published in the English language, up to January 2022, were included regarding the influence of surface patterning on bond strength of Y-TZP to resin-matrix cements. Out of the 12 studies selected for the present review 10 studies assessed femtosecond lasers while 2 studies assessed picosecond lasers. Ultrashort pulsed laser surface patterning successfully produced different surface morphological aspects without damaging the bulk properties of zirconia. Contrarily, defects such as micro-cracks occurs after surface modification using traditional methods such as grit-blasting or long-pulsed laser patterning. Ultrashort pulsed laser surface patterning increase bond strength of zirconia to resin-matrix cements and therefore such alternative physical method should be considered in dentistry. Also, surface defects were avoided using ultrashort pulsed laser surface patterning, which become the major advantage when compared with traditional physical methods or long pulse laser patterning.

Porous Biocoatings Based on Diatomite with Incorporated ZrO2 Particles for Biodegradable Magnesium Implants

In the present work, the surface of a biodegradable Mg alloy was modified to create porous diatomite biocoatings using the method of micro-arc oxidation. The coatings were applied at process voltages in the range of 350-500 V. We have studied the influence of the addition of ZrO₂ microparticles on the structure and properties of diatomite-based protective coatings for Mg implants. The structure and properties of the resulting coatings were examined using a number of research methods. It was found that the coatings have a porous structure and contain ZrO₂ particles. The coatings were mostly characterized by pores less than 1 μm in size. However, as the voltage of the MAO process increases, the number of larger pores (5-10 μm in size) also increases. However, the porosity of the coatings varied insignificantly and amounted to 5 ± 1%. It has been revealed that the incorporation of ZrO₂ particles substantially affects the properties of diatomite-based coatings. The adhesive strength of the coatings has increased by approximately 30%, and the corrosion resistance has increased by two orders of magnitude compared to the coatings without zirconia particles.

Effect of different surface treatments on the biaxial flexural strength of zirconia ceramics

STATEMENT OF PROBLEM

Different surface treatments have been applied to zirconia restorations in clinical practice to increase the bond strength between zirconia and cement, but their effect on flexural strength is unknown.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of different surface treatments before and after sintering on the flexural strength of zirconia.

MATERIAL AND METHODS

Sixty disk-shaped specimens with an initial diameter of 18.6 ±0.1 mm and thickness of 2 ±0.1 mm were prepared from preshaded presintered 3Y-TZP blocks. The specimens were randomly divided into 3 groups (n=20) according to surface treatments (Group Laser, Group APA, Group Rocatec), and the groups were then divided into 2 subgroups (n=10) according to surface treatment before and after sintering. The phase compositions of the groups were examined by using an X-ray diffractometer (XRD) with 3 randomly selected specimens from each group. Biaxial flexural strength testing was conducted using a universal testing machine to examine the flexural strength of the zirconia specimens. Two-way ANOVA and post hoc least significant difference tests were performed (α=.05).

RESULTS

According to the XRD analysis, no monoclinic phases were determined on the surface of the presintered laser-treated specimens, but tetragonal phases were observed on the surface of the postsintered specimens. Surface treatment type and application stage (presintering to postsintering) have a significant effect on the biaxial flexural strength of the specimens (P<.05). The lowest biaxial flexural values were observed in the Laser group, and postsintered specimens showed higher biaxial flexural strength than presintered specimens (P<.05).

CONCLUSIONS

Postsintered specimens showed higher monoclinic content than presintered specimens. Laser-treated specimens showed the lowest biaxial flexural strength for both presintered and postsintered specimens.

ROS-Generating Hyaluronic Acid-Modified Zirconium Dioxide-Acetylacetonate Nanoparticles as a Theranostic Platform for the Treatment of Osteosarcoma

Materials that are able to produce free radicals have gained increasing attention for environmental and biomedical purposes. Free radicals, such as the superoxide anion (O₂^•-), act as secondary messengers in many physiological pathways, such as cell survival. Therefore, the production of free radicals over physiological levels has been exploited in the treatment of different types of cancer, including osteosarcoma (OS). In most cases, the production of reactive oxygen species (ROS) by materials is light-induced and requires the use of chemical photosensitisers, making it difficult and expensive. Here, for the first time, we propose photoluminescent hybrid ZrO₂-acetylacetonate nanoparticles (ZrO₂-acac NPs) that are capable of generating O₂^•- without light activation as an adjuvant for the treatment of OS. To increase the uptake and ROS generation in cancer cells, we modify the surface of ZrO₂-acac NPs with hyaluronic acid (HA), which recognizes and binds to the surface antigen CD44 overexpressed on OS cells. Since these nanoparticles emit in the visible range, their uptake into cancer cells can be followed by a label-free approach. Overall, we show that the generation of O₂^•- is toxic to OS cells and can be used as an adjuvant treatment to increase the efficacy of conventional drugs.

Microstructure, Mechanical, In Vitro Biodegradation, and Antimicrobial Behavior of a Mg-Zn-Ca-Sr/ZrO2 Composite Prepared Using Powder Metallurgy

Biodegradable materials, especially Mg alloys, have an exceptional advantage over nonbiodegradable materials in orthopedic applications, such as avoiding second surgery for removal/replacement, stress shielding, but not enough mechanical strength, and so forth. By further improving the Mg alloy to get all the remaining required properties, it can be used for better biodegradable implants, which depend adequately on material optimization, processing, and so forth. A Mg-Zn-Ca-Sr/ZrO₂ composite has been prepared using powder metallurgy by adding 0, 1, 2, and 3 wt % of ZrO₂, which also contains Zn, Ca, and Sr as nutrient elements. Microstructure characterization, as well as mechanical and in vitro biodegradation, have been investigated by hardness, compression, and immersion tests. The highest compressive strength, contraction, and hardness of about 185.6 MPa, 9.5%, and 65.2 HRB are observed in the 2% ZrO₂-containing composite, respectively, whereas a minimum biodegradation rate of 2.76 mm/year is observed on the same. The antibiotic sensitivity observations against Staphylococcus aureus suggest that the alloy C3 has superior biological activity against the pathogen which ranks this alloy on top in merit. Overall, Mg-Zn-Ca-Sr/ZrO₂ exhibits impressive potential for use as a biodegradable and antibiotic material for orthopedic applications.

Structure and Spectral Luminescence Properties of (ZrO2)0.909(Y2O3)0.09(Eu2O3)0.001 Ceramics Synthesized by Uniaxial Compaction and Slip Casting

The structure, phase composition and spectral luminescence properties of single crystal and ceramic specimens of (ZrO₂)_0.909(Y₂O₃)_0.09(Eu₂O₃)_0.001 solid solutions synthesized using uniaxial compaction and slip casting techniques have been compared. The ceramic specimens have been synthesized from crushed single crystal specimens of similar composition. It has been shown that the crystalline structures of the ceramic and single crystal specimens are identical and cubic. The ceramic specimens synthesized using different methods prove to have close microstructure patterns. The spectral luminescence properties of Eu³⁺ ions in the (ZrO₂)_0.909(Y₂O₃)_0.09(Eu₂O₃)_0.001 ceramic specimens are similar to those of the single crystals with similar composition. The (ZrO₂)_0.909(Y₂O₃)_0.09(Eu₂O₃)_0.001 ceramic specimens prove to have uncontrolled Cr³⁺:Al₂O₃ impurities due to the synthesis conditions.

3D Printing of Bioinert Oxide Ceramics for Medical Applications

Three-dimensionally printed metals and polymers have been widely used and studied in medical applications, yet ceramics also require attention. Ceramics are versatile materials thanks to their excellent properties including high mechanical properties and hardness, good thermal and chemical behavior, and appropriate, electrical, and magnetic properties, as well as good biocompatibility. Manufacturing complex ceramic structures employing conventional methods, such as ceramic injection molding, die pressing or machining is extremely challenging. Thus, 3D printing breaks in as an appropriate solution for complex shapes. Amongst the different ceramics, bioinert ceramics appear to be promising because of their physical properties, which, for example, are similar to those of a replaced tissue, with minimal toxic response. In this way, this review focuses on the different medical applications that can be achieved by 3D printing of bioinert ceramics, as well as on the latest advances in the 3D printing of bioinert ceramics. Moreover, an in-depth comparison of the different AM technologies used in ceramics is presented to help choose the appropriate methods depending on the part geometry.

Fracture strength of monolithic and glass-soldered ceramic sub-components of 5-unit fixed dental prosthesis

PURPOSE

Zirconium dioxide ceramic has been successfully introduced as a framework material for fixed dental prostheses. To reduce manufacturing constraints, joining of sub-components could be a promising approach to increase the mechanical performance of long-span fixed dental prostheses. In this experimental study, the biomechanical behavior of monolithic and soldered framework specimens for fixed dental prostheses made of Y-TZP was investigated.

MATERIALS AND METHODS

Framework specimens (n  =  80) of 5-unit fixed dental prostheses made of Y-TZP were prepared and divided into 10 equal groups. The specimens were monolithic or composed of sub-components, which were joined using a silicate-based glass solder. Thereby, three joint geometries (diagonal, vertical with an occlusal cap, and dental attachment-based) were investigated. Moreover, the groups differed based on the mechanical test (static vs. dynamic) and further processing (veneered vs. unveneered). The framework specimens were cemented on alumina-based jaw models, where the canine and second molar were acting as abutments, before a point-load was applied. In addition, μCT scans and microscopic fractography was used to evaluate the quality of soldered joints and to determine the causes of fracture.

RESULTS

The determined fracture loads of the different unveneered framework specimens in static testing did not vary significantly (p  =  1). Adding a veneering layer significantly increased the mechanical strength for monolithic framework specimens from 1,196.29 ±203.79 N to 1,606.85 ±128.49 N (p  =  0.008). In case of soldered specimens with a dental attachment-based geometry the mechanical strength increased from 1,159.42 ±85.65 N to 1,249.53 ±191.55 N (p  =  1). Within the dynamic testing, no differences were observed between monolithic and soldered framework specimens. μCT scans and fractography proved that the dental attachment-based joining geometry offers the highest quality.

CONCLUSION

Using glass soldering technology, sub-components of 5-unit framework specimens made of Y-TZP could be joined with mechanical properties comparable to those of monolithic frameworks. This article is protected by copyright. All rights reserved.

Evaluation of the Biocompatibility and Osteogenic Properties of Metal Oxide Coatings Applied by Magnetron Sputtering as Potential Biofunctional Surface Modifications for Orthopedic Implants

Biomaterials with adequate properties to direct a biological response are essential for orthopedic and dental implants. The surface properties are responsible for the biological response; thus, coatings with biologically relevant properties such as osteoinduction are exciting options to tailor the surface of different bulk materials. Metal oxide coatings such as TiO₂, ZrO₂, Nb₂O₅ and Ta₂O₅ have been suggested as promising for orthopedic and dental implants. However, a comparative study among them is still missing to select the most promising for bone-growth-related applications. In this work, using magnetron sputtering, TiO₂, ZrO₂, Ta₂O₅, and Nb₂O₅ thin films were deposited on Si (100) substrates. The coatings were characterized by Optical Profilometry, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy, X-ray Photoelectron Spectroscopy, X-ray Diffraction, Water Contact Angle measurements, and Surface Free Energy calculations. The cell adhesion, viability, proliferation, and differentiation toward the osteoblastic phenotype of mesenchymal stem cells plated on the coatings were measured to define the biological response. Results confirmed that all coatings were biocompatible. However, a more significant number of cells and proliferative cells were observed on Nb₂O₅ and Ta₂O₅ compared to TiO₂ and ZrO_2. Nevertheless, Nb₂O₅ and Ta₂O₅ seemed to induce cell differentiation toward the osteoblastic phenotype in a longer cell culture time than TiO₂ and ZrO₂.

Effect of Erosive Agents on Surface Characteristics of Nano-Fluorapatite Ceramic: An In-Vitro Study

Erosive beverages cause dissolution of natural teeth and intra-oral restorations, resulting in surface characteristic changes, particularly roughness and degradation. The purpose of this study was to evaluate the surface roughness and topography of a dental ceramic following immersion in locally available erosive solutions. A total of 160 disc specimens of a nano-fluorapatite type ceramic (12 mm diameter and 2 mm thickness) were fabricated and equally distributed into two groups (n = 80) and then evenly distributed among the following five testing groups (n = 16): lemon juice, citrate buffer solution, 4% acetic acid, soft cola drink, and distilled water which served as a control. The surface roughness (Ra) and topography were evaluated using a profilometer and scanning electron microscope at baseline, 24 h, 96 h, and 168 h respectively. Data were analyzed using ANOVA and Tukey's multiple comparisons (p ≤ 0.05). Surface changes were observed upon exposure to all acidic beverages except distilled water. Amongst all immersion media, 4% acetic acid produced the most severe surface roughness across all time periods (i.e., baseline, 24 h, 96 h, and 168 h). A statistically significant difference in the surface roughness values between all immersion media and across all four time intervals was observed. Erosive agents had a negative effect on the surface roughness and topography of the tested ceramic. The surface roughness increased with increased storage time intervals.

Effects of Different Polishing Systems on Surface Roughness and Crystal Structure of Zirconia

Objective

Intraoral polishing systems have become an alternative method for reglazing, which is important to prevent or minimize rapid wear of the opposing teeth. To assess the influence of different polishing systems and duration on surface roughness and crystal structure of zirconia was compared, contributing to the preparation and effect improvement of clinical zirconia restorations.

Methods

Forty-eight zirconia specimens with equal size were fabricated by cutting and sintering zirconia discs. Then X-ray diffractometer (XRD) was adopted for examination of the specimens. Six specimens were selected as the grinding-polishing group (GL) after polishing, grinding, and glazing. Then six specimens were randomly selected from the remaining specimens as the grinding-unpolished group (GR) after surface conditioning by dental diamond burs. Subsequently, based on different polishing systems and duration, the rest of specimens were divided into following groups (n = 6): Youdent-20s group (Y20), Youdent-40s group (Y40), Youdent-60s group (Y60), Toboom-20s group (T20), Toboom-40s group (T40), and Toboom-60s group (T60). Additionally, a contour graph was applied for assessing the surface roughness of zirconia, scanning electron microscope (SEM) for observing surface topography, and X-ray diffraction analysis (XRD) for determining crystal structure of zirconia.

Results

The GR group had the highest roughness, and the roughness of the specimens polished for 20 s with different polishing systems was significantly higher than those polished for 40 s and 60 s with the same polishing systems. There were no significant difference between the Y20 and T20 groups, while the roughness of the specimens in both Y40 and Y60 groups was significantly higher than that of the T40 and T60 groups. And with the increasing polishing duration, the surface morphology of the specimen was gradually smooth and the morphology was gradually regular. Besides, the surface scratches of the T group were shallower than that of the Y group at the same polishing duration. The peak value of XRD profile of the specimen after grinding and polishing process was consistent with the baseline pattern of that the original specimen.

Conclusion

Glazing can reduce the surface roughness of the specimens. Besides, the polishing effect of Toboom (TOB) system (polishing duration = 60 s) is the best. And different polishing durations of TOB system have no significant effect on the crystal surface structure of the specimen.

High-Density Nanowells Formation in Ultrafast Laser-Irradiated Thin Film Metallic Glass

We present an effective approach for fabricating nanowell arrays in a one-step laser process with promising applications for the storage and detection of chemical or biological elements. Biocompatible thin films of metallic glasses are manufactured with a selected composition of Zr₆₅Cu₃₅, known to exhibit remarkable mechanical properties and glass forming ability. Dense nanowell arrays spontaneously form in the ultrafast laser irradiation spot with dimensions down to 20 nm. The flared shape observed by transmission electron microscopy is ideal to ensure chemical or biological material immobilization into the nanowells. This also indicates that the localization of the cavitation-induced nanopores can be tuned by the density and size of the initial nanometric interstice from the columnar structure of films deposited by magnetron sputtering. In addition to the topographic functionalization, the laser-irradiated amorphous material exhibits structural changes analyzed by spectroscopic techniques at the nanoscale such as energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy. Results reveal structural changes consisting of nanocrystals of monoclinic zirconia that grow within the amorphous matrix. The mechanism is driven by local oxidation process catalyzed by extreme temperature and pressure conditions estimated by an atomistic simulation of the laser-induced nanowell formation.

Nanostructured Coatings: Review on Processing Techniques, Corrosion Behaviour and Tribological Performance

Corrosion and tribology are surface phenomena. Modifying surfaces of materials without resorting to altering their bulk properties is an effective route to alleviate corrosion, friction and wear, encountered in engineering applications. With the advancements in the field of nanotechnology, surface protective coatings with nanomaterials can be readily developed to explore their functionality in mitigating chemical/physical damage of surfaces. Surface protection enhances performance and operating lifetimes of industrial machinery components. This review presents insights on various types of recently developed nanostructured coatings, their synthesis routes, corrosion behaviour and tribological performance. It provides the state-of-the-art information on the development of nanostructured coatings, namely, ceramic coatings, metallic coatings and nanocomposite coatings with metal and polymer matrices. Biomimetic approaches in making nanostructured coatings and challenges encountered in the development of nanostructured coatings are highlighted.

Size Attenuated Copper Doped Zirconia Nanoparticles Enhances In Vitro Antimicrobial Properties

Biofilm formation hinders the activity of antimicrobial drugs at the site of infections and any agent that can act on both Gram-positive and Gram-negative bacteria by inhibiting the bacterial growth and rupturing the biofilm is needed to manage infection. In the present study, we have synthesized zirconia nanoparticles (ZrO₂ NPs) and copper doped zirconia nanoparticles (Cu-ZrO₂ NPs) and characterized them using dynamic light scattering, X-ray diffractometry, and scanning electron microscopy (SEM). The size of the Cu-ZrO₂ NPs drastically reduced compared to ZrO₂ NPs, and the antimicrobial activity was studied against Gram-positive bacteria (Lactobacillus sp.) and Gram-negative bacteria (Pseudomonas aeruginosa), respectively. The synthesized Cu-ZrO₂ NPs showed superior inhibitory action against Lactobacillus sp. compared to ZrO₂ NPs, due to the negatively charged cell wall of Lactobacillus sp., which could attract readily the positively charged Cu-ZrO₂ NPs, thereby inhibiting its activity. The biocompatibility was tested using XTT assay in FL cells, and the results demonstrated that Cu-ZrO₂ NPs were nontoxic to mammalian cells. Hence, it could be proposed that the synthesized Cu-ZrO₂ NPs possess possible biomedical applications and can be used as antibacterial agents without causing toxicity in mammalian cells.

Success Factors of Additive Manufactured Root Analogue Implants

Dental implantation is an effective method for the treatment of loose teeth, but the threaded dental implants used in the clinic cannot match with the tooth extraction socket. A root analogue implant (RAI) has the congruence shape, which reduces the damage to bone and soft tissue. Additive manufacturing (AM) technologies have the advantages of high precision, flexibility, and easy operation, becoming the main manufacturing method of RAI in basic research. The purpose of this systematic review is to summarize AM technologies used for RAI manufacturing as well as the factors affecting successful implantation. First, it introduces the AM technologies according to different operating principles and summarizes the advantages and disadvantages of each method. Then the influences of materials, structure design, surface characteristics, implant site, and positioning are discussed, providing reference for designers and dentists. Finally, it addresses the gap between basic research and clinical application for additive manufactured RAIs and discusses the current challenges and future research directions for this field.

Influence of firing temperature and duration on the hardness of dental zirconia for optimum selection of sintering conditions

OBJECTIVE

In order to optimize the properties of dental zirconia, the sintering process involves firing zirconia to elevated temperatures for an extended time that can take several hours. The aim of this study is to investigate the effect of firing temperature and firing duration on the hardness of dental zirconia to indicate the optimum sintering conditions.

METHODS

Thirty-six zirconia specimens in shape of bars were randomly assigned to nine groups. The zirconia specimen groups were sintered using a sintering furnace with different firing temperatures (900°C, 1200°C, and 1800°C) and firing durations (6, 9, and 12 h). A total of 108 hardness measurements were conducted for all specimens (12 hardness readings per group). For each of the specimen groups, micro Vickers hardness test was performed using a load of 1 Kgf (9.807 N) and the Vickers hardness number was computed. Statistical analysis using Kruskal-Wallis test was conducted to examine the significant differences on Vickers hardness number HV among the specimen groups according to the firing parameters with 0.005 p-value used as an indicator.

RESULTS

Results suggest that there is an association between the increase in the hardness number and the increase in firing duration at a given firing temperature. The results also indicate that there is an association between the increase in the hardness number and increase in firing temperature at a given firing duration.

CONCLUSIONS

The greatest rate of hardness increase with time is associated with groups of firing temperature 1200°C. The highest rate of hardness increase with temperature happened during the first 6 h of sintering process. On the other hand, there is no significant increase in the hardness number when increasing the firing temperature beyond 1200°C.

Effect of binder system on the thermophysical properties of 3D-printed zirconia ceramics

Fabrication of 3D-printed ceramic parts with high complexity and high spatial resolution often demands low wall thickness as well as high stiffness at the green state, whereas printing simpler geometries may tolerate thicker, more compliant walls with the advantage of a rapid binder-burn-out and sintering process. In this work, the influence of the binder system on the thermophysical properties of 3D-printed stabilized zirconia ceramics was investigated. Samples were fabricated with the lithography-based ceramic manufacturing (LCM) technology using two different photosensitive ceramic suspensions (LithaCon 3Y230 and LithaCon 3Y210), with the same ZrO2 powder. A significant difference in stiffness in the green state (~3 MPa vs. ~32 MPa for LithaCon 3Y230 and LithaCon 3Y210, respectively) was measured, associated with a rather loose or a linked network formed in the binder due to photopolymerization. Both materials reached high relative densities, that is, >99%, exhibiting a homogeneous fine-grained microstructure. No significant differences on the coefficient of thermal expansion (11.18 ppm/K vs. 11.17 ppm/K) or Young's modulus (207 GPa vs. 205 GPa) were measured, thus demonstrating the potential of tailoring binder systems to achieve the required accuracy in 3D-printed parts, without detrimental effects on material's microstructure and thermophysical properties at the sintered state.

Characterization of 3D Printed Yttria-Stabilized Zirconia Parts for Use in Prostheses

The main aim of the present paper is to study and analyze surface roughness, shrinkage, porosity, and mechanical strength of dense yttria-stabilized zirconia (YSZ) samples obtained by means of the extrusion printing technique. In the experiments, both print speed and layer height were varied, according to a 2² factorial design. Cuboid samples were defined, and three replicates were obtained for each experiment. After sintering, the shrinkage percentage was calculated in width and in height. Areal surface roughness, S_a, was measured on the lateral walls of the cuboids, and total porosity was determined by means of weight measurement. The compressive strength of the samples was determined. The lowest S_a value of 9.4 μm was obtained with low layer height and high print speed. Shrinkage percentage values ranged between 19% and 28%, and porosity values between 12% and 24%, depending on the printing conditions. Lowest porosity values correspond to low layer height and low print speed. The same conditions allow obtaining the highest average compressive strength value of 176 MPa, although high variability was observed. For this reason, further research will be carried out about mechanical strength of ceramic 3D printed samples. The results of this work will help choose appropriate printing conditions extrusion processes for ceramics.

Ten-year clinical performance of zirconia posterior fixed partial dentures

BACKGROUND

With the constantly increasing demand for metal-free solutions in dental therapy, numerous ceramic restorations have found their way into everyday clinical practice, but long-term clinical data are limited.

OBJECTIVE

The aim of this prospective clinical study was to evaluate three- and four-unit fixed partial dentures in the posterior region made of zirconium dioxide frameworks veneered with feldspathic porcelain after 10 years in clinical use.

METHODS

Based on the two studies published in 2009 and 2012, in which the all-ceramic FDPs were evaluated after 3 and 5 years of function, a clinical evaluation of a total of 17 restorations after 10 years with regard to their condition and long-term stability was carried out in the course of this study. The restorations were fabricated using feldspathic ceramic-veneered, yttria-stabilised, tetragonal zirconium dioxide as the framework material. The data collection was based on modified CDA criteria and included, for example, the shape, shade, surface condition and the success and survival rates of the restorations.

RESULTS

The all-ceramic prostheses embodied excellent biocompatibility and colour reproduction. As a result of an increased incidence of chipping fractures, the success rate was 60%. The survival rate, however, was 88.2%, as 2 of the 17 restorations were lost.

CONCLUSION

All-ceramic concepts for FDP constructions in the posterior region achieved satisfactory results in terms of durability after 10 years. The main problem was chipping, as has been generally recognised. Nevertheless, the materials were characterised by excellent aesthetics and biocompatibility, which ultimately makes them a good alternative to conventional restorative options.

TRIAL REGISTRATION

This study is registered in DRKS-German Clinical Trials Register with the register number DRKS00021743.

Artificial Intelligence in Biomedical Applications of Zirconia

Artificial intelligence (AI) is rapidly developed based on computer technology, which can perform tasks that customarily require human intelligence by building intelligent software or machines. As a subfield of AI, machine learning (ML) can learn from the intrinsic statistical patterns and structures in data through algorithms to predict invisible data. With the increasing interest in aesthetics in dentistry, zirconia has drawn lots of attention due to its superior biocompatibility, aesthetically pleasing, high corrosion resistance, good mechanical properties, and absence of reported allergic reactions. The evolution of AI and ML led to the development of novel approaches for the biomedical applications of zirconia in dental devices. AI techniques in zirconia-related research and clinical applications have attracted much attention due to their ability to analyze data and reveal correlations between complex phenomena. The AI applications in the field of zirconia science change according to the application direction of zirconia. Therefore, in this article, we focused on AI in biomedical applications of zirconia in dental devices and AI in zirconia-related applications in dentistry.

Sol-Gel Synthesis and Characterization of a Quaternary Bioglass for Bone Regeneration and Tissue Engineering

Sol-gel synthesis using inorganic and/or organic precursors that undergo hydrolysis and condensation at room temperature is a very attractive and less energetic method for preparing bioactive glass (BG) compositions, as an alternative to the melt-quenching process. When properly conducted, sol-gel synthesis might result in amorphous structures, with all of the components intimately mixed at the atomic scale. Moreover, developing new and better performing materials for bone tissue engineering is a growing concern, as the aging of the world's population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2-34 CaO-4 MgO-2 P2O5 (mol%), which was prepared using acidified distilled water as a single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The XRD results of samples calcined within the temperature range of 600-900 °C demonstrated that the amorphous nature was maintained until 800 °C, followed by partial crystallization at 900 °C. The specific surface area-an important factor in osteoconduction-was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 °C to 2.2 ± 0.1 m2/g at 900 °C, accompanied by consistent changes in average pore size and pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate that the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

Zirconia Based Dental Biomaterials: Structure, Mechanical Properties, Biocompatibility, Surface Modification, and Applications as Implant

Zirconia, with its excellent mechanical properties, chemical stability, biocompatibility, and negligible thermal conductivity, is ideal for dental and orthopedic applications. In addition, the biocompatibility of zirconia has been studied in vivo, and no adverse reactions were observed when zirconia samples were inserted into bone. However, their use is controversial among dentists and researchers, especially when compared with mature implants made of titanium alloy. The advantages and limitations of zirconia as biomaterials, such as implant materials, need to be carefully studied, and the design, manufacture, and clinical operation guidelines are urgently required. In this review, the special components, microstructure, mechanical strength, biocompatibility, and the application of zirconia ceramics in biomaterials are detailly introduced. The review highlights discussions on how to implement innovative strategies to design the physical and chemical properties of zirconia so that the treated zirconia can provide better osteointegration after implantation.

Tailoring the biological response of zirconium implants using zirconia bioceramic coatings: A systematic review

BACKGROUND

The poor biological performance of zirconium implants in the human body resulting from their bio-inertness and vulnerability to corrosion and bacterial activity reflects the need for further studies on substitution or performing the surface modification. The suggestion of employing zirconia (ZrO₂) bioceramic coatings for surface modification seems beneficial.

OBJECTIVES

This systematic review aims to identify and summarize existing documents reporting the biological responses for ZrO₂ coatings produced by the PEO process on zirconium implants.

METHODS

PubMed, Scopus, and Web of Science international databases were searched for the original and English-language studies published between 2000 and 2021. All publications reported at least one study about in-vitro (cellular and immersion studies), in-vivo (animal studies), and antibacterial topics for ZrO₂-PEO coated zirconium implants.

RESULTS

Throughout the initial search, 496 publications were found, and 296 papers remained following the elimination of duplicates. Finally, after multiple screening and eligibility assessments, 25 publications were qualified and included in the review. Among them, 25 in-vitro (cellular and immersion in SBF and Hanks' solutions studies), one in-vivo (animal studies), and eight antibacterial studies were found.

CONCLUSION

The ZrO₂ coated samples demonstrate no cytotoxicity, high cell viability rate, and excellent biocompatibility. However, changing the solution composition and electrical parameters during the PEO procedures result in significant changes to in-vitro responses. As an instance, the ZrO₂ coating surface demonstrates greater biocompatibility after irradiated by UV, which makes the surface more suitable for cell growth. Due to weak apatite-forming ability, the zirconium sample shows low bioactivity in SBF. However, most cases (13 out of 16) show that the specific morphology and chemical composition of the ZrO₂ coating promote apatite-forming ability with good bioactivity in SBF. Nevertheless, few papers (three out of 16) showed that the ZrO₂ coatings immersed in SBF had no apatite precipitates and so no bioactivity. These cases limit the bioactivity enhancement to treatment by UV-light irradiation, hydrothermal and chemical treatment, thermal evaporation, and cathodic polarization post-treatment on ZrO₂ coatings. Both zirconium and ZrO₂ coated samples do not show apatite-forming ability in Hanks' solution. The ZrO₂ coated implant with the bone together indicates a greater shear strength and rapid new bone formation ability during 12 weeks because of containing Ca-P compounds and porous structure. The UV post-treated ZrO₂ coating induces faster new bone formation and firmer connection of bond with bone than those of untreated ZrO₂ coatings. A stronger antibacterial activity of ZrO₂ coatings is confirmed in half of the selected papers (four out of eight studies) compared to the bare zirconium samples. The antibacterial protection of ZrO₂ coatings can be influenced by the PEO procedure variables, i.e., solution composition, electrical parameters, and treatment time. In three cases, the antibacterial activity of ZrO₂ coatings is enhanced by deposition of Zn, Ag, or Cu antibacterial layers through thermal evaporation post-treatment.

Three-Dimensional Zirconia-Based Scaffolds for Load-Bearing Bone-Regeneration Applications: Prospects and Challenges

The design of zirconia-based scaffolds using conventional techniques for bone-regeneration applications has been studied extensively. Similar to dental applications, the use of three-dimensional (3D) zirconia-based ceramics for bone tissue engineering (BTE) has recently attracted considerable attention because of their high mechanical strength and biocompatibility. However, techniques to fabricate zirconia-based scaffolds for bone regeneration are in a stage of infancy. Hence, the biological activities of zirconia-based ceramics for bone-regeneration applications have not been fully investigated, in contrast to the well-established calcium phosphate-based ceramics for bone-regeneration applications. This paper outlines recent research developments and challenges concerning numerous three-dimensional (3D) zirconia-based scaffolds and reviews the associated fundamental fabrication techniques, key 3D fabrication developments and practical encounters to identify the optimal 3D fabrication technique for obtaining 3D zirconia-based scaffolds suitable for real-world applications. This review mainly summarized the articles that focused on in vitro and in vivo studies along with the fundamental mechanical characterizations on the 3D zirconia-based scaffolds.