Removal of ceftriaxone sodium antibiotic from pharmaceutical wastewater using an activated carbon based TiO2 composite: Adsorption and photocatalytic degradation evaluation

Recent advances in titanium dioxide bio-derived carbon photocatalysts for organic pollutant degradation in wastewater

Water pollution from organic pollutants such as dyes and pharmaceuticals poses severe threats to ecosystems and human health, demanding effective remediation strategies. Conventional water treatment methods fall short in eliminating these contaminants, prompting interest in photocatalysis, which uses light energy to degrade pollutants into harmless substances such as carbon dioxide and water. This sustainable approach offers efficient pollutant removal with recyclable photocatalysts but faces challenges such as rapid charge recombination and limited electron-hole migration. Research aims to enhance photocatalytic efficiency under UV, visible, and solar light through metal doping and binary oxide systems, particularly titanium dioxide, which improves charge carrier migration and delays recombination. Coupling titanium dioxide with bio-derived carbon shows promise in enhancing electron-hole separation and visible light absorption. This review explores advances in photocatalyst synthesis, degradation mechanisms, adsorption reactions, and economic value of bioderived photocatalysts, emphasizing the potential of photocatalysis for efficient wastewater treatment.

Tetracycline removal from aqueous media and hospital wastewater using a magnetic composite of mango lignocellulosic kernel biochar/MnFe2O4/Cu@Zn-BDC MOF

This study explored the use of mango lignocellulosic kernel biochar (MKB) modified with MnFe2O4 magnetic nanoparticles and a Cu@Zn-BDC metal-organic framework (MOF) (MKB/MnFe2O4/Cu@Zn-BDC MOF) for tetracycline (TC) removal from aqueous solutions and hospital wastewater. The modified biochar exhibited strong magnetic properties (19.803 emu/g) and a specific surface area of 30.456 m2/g, facilitating easy separation after adsorption. Using Response Surface Methodology-Central Composite Design (RSM-CCD), the adsorption model demonstrated high accuracy (F-value: 315.510, p < 0.0001, R2 = 0.9959). Thermodynamic analysis indicated that the process was endothermic and spontaneous, driven by physical interactions, with positive enthalpy and negative Gibbs free energy values. The pseudo-second-order kinetic model best described the adsorption, highlighting significant chemical interactions, while the Freundlich isotherm suggested adsorption on heterogeneous surfaces. The maximum TC adsorption capacities for MKB and its magnetic composite were 27.050 mg/g and 42.670 mg/g, respectively. The RL, n, and E parameters confirmed the desirability and physical nature of the interactions (0-1,〉1, and < 8 kJ/mol, respectively). The intraparticle diffusion model indicated multiple mechanisms were involved, and the biochar maintained excellent performance across reuse cycles, making it a highly effective and reusable adsorbent for water and wastewater treatment.

Emerging strategies in the sustainable removal of antibiotics using semiconductor-based photocatalysts

In the constantly growing field of environmental sustainability, the threat of newly discovered pollutants, particularly antibiotics, has become a crucial concern. The widespread presence of these pharmaceutical substances in water sources presents a complex hazard to human health and ecological balance, requiring immediate and novel intervention techniques. Regarding this, semiconductor-based photocatalysts have appeared as promising candidates, providing a sustainable and efficient way to remove antibiotics from aquatic ecosystems. Nanomaterials can effectively and precisely break down and neutralize antibiotic compounds with high efficiency and selectivity by utilizing a complex interaction between radical reactive oxygen species and non-radical equivalents under light irradiation. Although photocatalysts have certain drawbacks, such as a limited capacity to absorb light and concerns about catalytic stability, photocatalysis outperforms other advanced oxidation processes in multiple aspects. This study focuses on summarizing recent advances in the sustainable removal of antibiotics using semiconductor-based photocatalysts. By reviewing the latest studies and sustainable technologies, this study presents new insights into the complex relationship between contaminants and catalytic degradation processes. Compared to single and binary photocatalysts, modified ternary composites were found to have superior photodegradation performance under visible light exposure. To be specific g-C3N4-based ternary photocatalysts exhibited more than 90% degradation of tetracycline and sulfamethazine antibiotics within one hour of irradiation. This study addresses the antibiotic degradation efficiency during photocatalytic processes and suggests new approaches to improve the performance and scalability for wider use in real-world situations.

Self-assembly of ZnO-Biochar/Kaolinite/Chitosan/GO with 1D/2D/3D heterojunctions for enhanced removal of estrogens and triclosan in water

This Study focuses on the preparation of sustainable and efficient Chitosan catalyst for the removal of three organic pollutants, 17β-Estradiol (E2), 17α-ethynyl estradiol (EE2) and triclosan (TCS) from water. The prepared nanocomposites were characterized by different techniques which confirmed the presence of the key components Chitosan, Carica Papaya seed and Kaolinite. The optical characterization proved the nanocomposite is photoactive with a band gap of 1.81 eV and 1.77 eV for Chitosan/kaolinite biochar (CS/KBC) and Chitosan/kaolinite biochar/GO (CS/KBC/GO) respectively, confirming the ability of the nanocomposite to be active in the visible light region of the spectrum. The degradation experiment using CS/KBC/GO was observed better with 100% removal for 5 mg/L E2 and EE2 over 60 min and 97.8% over 120 min for 10 mg/L TCS at optimum conditions (pH 3 for E2, and EE2 and pH 7). It was observed that the superoxide radical played a major role in the degradation of the contaminants. Furthermore, the CS/KBC/GO was efficient over four cycles without any decrease in performance, which rules out the question of catalyst deactivation proving the sustainability of the catalyst. The toxicity test shows that the water is safe as it does not harm cerio daphnia silvestrii organism.; CS/KBC/GO efficiently removed the micropollutants from real-life waste samples and the performance was very good with a slight decrease in performance for the wastewater due to the complex matrix of the water sample that competes for the active site.

Metallic nanoparticles unveiled: Synthesis, characterization, and their environmental, medicinal, and agricultural applications

Metallic nanoparticles (MNPs) have attracted great interest among scientists and researchers for years due to their unique optical, physiochemical, biological, and magnetic properties. As a result, MNPs have been widely utilized across a variety of scientific fields, including biomedicine, agriculture, electronics, food, cosmetics, and the environment. In this regard, the current review article offers a comprehensive overview of recent studies on the synthesis of MNPs (metal and metal oxide nanoparticles), outlining the benefits and drawbacks of chemical, physical, and biological methods. However, the biological synthesis of MNPs is of great importance considering the biocompatibility and biological activity of certain MNPs. A variety of characterization techniques, including X-ray diffraction, transmission electron microscopy, UV-visible spectroscopy, scanning electron microscopy, dynamic light scattering, atomic force microscopy, Fourier transform infrared spectroscopy, and others, have been discussed in depth to gain deeper insights into the unique structural and spectroscopic properties of MNPs. Furthermore, their unique properties and applications in the fields of medicine, agriculture, and the environment are summarized and deeply discussed. Finally, the main challenges and limitations of MNPs synthesis and applications, as well as their future prospects have also been discussed.

A state-of-the-art review on lignocellulosic biomass-derived activated carbon for adsorption and photocatalytic degradation of pollutants: a property and mechanistic study

A promising water treatment method involves using biomass-derived activated carbon (AC) to remove emerging pollutants from wastewater due to its adsorption capacity, cost-effectiveness, and sustainability. Notwithstanding, the existing literature lacks comprehensive studies that specifically focus on removing contaminants in water by comparing the effectiveness of adsorption and photocatalytic degradation methods. Additionally, there is not much emphasis on analyzing the combined processes of adsorption-photocatalytic degradation utilizing AC. Herein, this paper investigates the intricacies of adsorption-photocatalytic degradation mechanisms and contributing variables in the enhancement of performances using biomass-derived AC. Furthermore, this review paper presents a comprehensive examination of different biomass sources employed in the synthesis of AC. It also discusses the diverse techniques utilized for the fabrication of AC, including physical and chemical activation methods. Finally, the shortcomings and future prospects of biomass-derived AC have been addressed. This study offers significant insights for the development of future biomass-derived AC, with the goal of improving their efficiency and expanding their uses in wastewater treatment.

Zirconium and cerium dioxide fabricated activated carbon-based nanocomposites for enhanced adsorption and photocatalytic removal of methylene blue and tetracycline hydrochloride

Activated carbon (AC) is a porous, amorphous form of carbon known for its strong adsorption capacity, making it highly effective for use in wastewater treatment. In this investigation, AC-based nanocomposites (NCs) loaded with zirconium dioxide and cerium dioxide nanoparticles (ZrO2/CeO2 NPs) were successfully synthesized for the effective elimination of methylene blue (MB) and tetracycline hydrochloride (TCH). The AC-ZrO2/CeO2 NCs have a size of 231.83 nm, a zeta potential of -20.07 mV, and a PDI value of 0.160. The adsorption capacities of AC-ZrO2/CeO2 NCs for MB and TCH were proved in agreement with the Langmuir isotherm and pseudo 1st order kinetic model, respectively. The maximum adsorption capacities were determined to be 75.54 mg/g for MB and 26.75 mg/g for TCH. Notably, AC-ZrO2/CeO2 NCs exhibited superior photocatalytic degradation efficiency for MB and TCH under sunlight irradiation with removal efficiencies reaching up to 97.91% and 82.40% within 90 min, respectively. The t1/2 for the photo-degradation process of MB and TCH were 11.55 min and 44.37 min. Analysis of active species trapping confirmed the involvement of hole (h+), superoxide anion (•O2-), and hydroxyl radical (•OH) in the degradation mechanism. Furthermore, the residual solution post-contaminant removal exhibited minimal toxicity towards Artemia salina and NIH3T3 cells. Importantly, the NCs did not exhibit antibacterial activity against tested pathogens post-absorption/degradation of TCH. Thus, AC-ZrO2/CeO2 NCs could be a promising nanomaterial for wastewater treatment applications.

Functionalization of MXene using iota-carrageenan, maleic anhydride, and N,N'-methylene bis-acrylamide for high-performance removal of thorium (IV), uranium (IV), sulfamethoxazole, and levofloxacin

An increasing quantity of pollutants has been discharged into the aquatic media, posing a serious hazard to public health. To address this issue, a new sorbent material, MXene@i.Carr@MaMb, was developed through the functionalization of the MXene surface using iota-carrageenan (i.Carr), maleic anhydride, and N, N'-methylene bis-acrylamide. This sorbent material was designed to remove thorium (Th (IV)) effectively, uranium (U (IV)), sulfamethoxazole (SMX), and levofloxacin (LEV) from wastewater. The MXene@i.Carr@MaMb composite incorporated significant functional groups, including OH, F, and O from MXene, oxygen and ester sulfate groups from iota-carrageenan (i.Carr), and OH, NH, and CO groups from N, N'-methylene bis-acrylamide, and maleic anhydride, which interacted with the UV (IV), Th (IV), SMX, and LEV pollutants through electrostatic interaction, complexation, and hydrogen bonding. MXene@i.Carr@MaMb composite exhibited excellent sorption capacities for Th (IV) (3.6 ± 0.03 mmol g-1), U (IV) (3.7 ± 0.09 mmol g-1), SMX (5.8 ± 0.03 mmol g-1), and LEV (5.9 ± 0.05 mmol g-1) at 323.15 K. The sorption kinetics and isotherms of radioactive metals and antibiotics can be well-described using pseudo-first-order kinetic models and Langmuir and Sips isothermal equations. This study presented a novel sorbent material for efficiently removing radioactive metals and antibiotics from wastewater.

Highly-efficient recovery of silver from industrial cyanide-based plating effluent on TiO2/activated carbon composites

The release of silver-containing wastewater is an economic loss. In this works, the silver ions in the cyanide-based plating effluent of jewelry effluent was systematic recovered by the photocatalytic process using commercial semiconductors (TiO2, ZnO, Bi2O3 and WO3) and activated carbon (AC) enhanced semiconductors as the photocatalysts. The preliminary results demonstrated that the highest photocatalytic silver recovery was achieved via the use of TiO2 nanoparticles (NPs), ascribing to its better textural property that provided abundant active sites to undergo the reaction. The intrinsic property and activity of TiO2 were significantly improved in the presence of proper content of AC. Approximately 94% of silver was recovered within 45 min through the TiO2/AC with 14.9 wt% AC (TiO2/AC1) under the UV-vis irradiation due to the act of AC as the conductive pathway for electron migration from CB of TiO2 along its surface, thus prolonging the lifetime of electron-hole pairs. Although a marked decrease in photocatalytic activity of the best composite was detected after the 4th use (∼50%), it exhibited an outstanding antibacterial ability compared with TiO2 and fresh one in dark environment. The work offers the avenue to design the photocatalyst for recovering the precious metals from industrial effluent and broaden the application of such recovered metal decorated photocatalyst for practical use.

Methylene blue removal using nano-TiO2/MWCNT/Chitosan hydrogel composite beads in aqueous medium

Dyestuff, one of the most hazardous compounds in terms of threats to people and the environment, is found in wastewater from industrial usage. The removal of Methylene Blue (MB) from a water-based medium has been studied by numerous researchers using a variety of adsorbents. To remove MB from aqueous solution, nano-TiO2/MWCNT/Chitosan hydrogel composite beads (n-TiO2/MWCNT/Cht) were developed in this study using a sol-gel method. This research discusses the characterisation of a new adsorbent substance using Infrared Spectroscopy (FT-IR) analysis and scanning electron microscopy (SEM). The optimal pH, adsorbent dosage, duration, and starting concentration were ascertained by analyzing the removal efficiencies of MB using the batch adsorption method. Adsorption behaviour at the equilibrium state has been investigated using a variety of adsorption isotherms, including Freundlich, Langmuir, and Dubinin-Radushkevich. The Langmuir adsorption isotherm has been useful to clarify adsorption behaviors. nTiO2-Cht/MWCNT had an adsorption capacity of 80.65 mg/g for MB. The pseudo-second-order kinetic model offered the best agreement to the experimental data for the adsorption of MB. Kinetic models of pseudo-first-order and pseudo-second-order were employed to explore the adsorption processes of MB on the n-TiO2/MWCNT/Cht. This study demonstrated the efficiency of n-TiO2/MWCNT/Cht for the removal of MB from a water-based solution.

A novel two stages chemical activation of pinewood waste for removing organic micropollutants from water and wastewater

The prevalent presence of pharmaceuticals in aquatic ecosystems underscores the necessity for developing cost-effective techniques to remove them from water. The utilization of affordable precursors in producing activated carbon, capable of rivaling commercial alternatives, remains a persistent challenge. The adsorption of diclofenac and ciprofloxacin onto a novel pinewood-derived activated carbon (FPWAC) was explored, employing a sequential activation process involving ammonium nitrate (NH4NO3) treatment followed by sodium hydroxide (NaOH) activation. The produced FPWAC was then thoroughly characterized by employing several techniques. The removal of diclofenac and ciprofloxacin in water and real wastewater effluent was examined in batch tests. The optimum removal conditions were an FPWAC dosage of 1 g L-1, pH 6, mixture concentration of 25 mg L-1, and a temperature of 25 °C. The FPWAC was able to remove both pharmaceuticals for up to six cycles, with more than 95% removal for water and 90% for wastewater in the first cycle. The adsorption performance fitted well with the non-linear Freundlich isotherm for both pollutants. The kinetics of adsorption of diclofenac followed a pseudo-first-order model, while ciprofloxacin showed adherence to the pseudo-second-order model. FPWAC proved its potency as a low-cost adsorbent for pharmaceutical removal from wastewater.

Metal oxide-based photocatalysts for the efficient degradation of organic pollutants for a sustainable environment: a review

Photocatalytic degradation is a highly efficient technique for eliminating organic pollutants such as antibiotics, organic dyes, toluene, nitrobenzene, cyclohexane, and refinery oil from the environment. The effects of operating conditions, concentrations of contaminants and catalysts, and their impact on the rate of deterioration are the key focuses of this review. This method utilizes light-activated semiconductor catalysts to generate reactive oxygen species that break down contaminants. Modified photocatalysts, such as metal oxides, doped metal oxides, and composite materials, enhance the effectiveness of photocatalytic degradation by improving light absorption and charge separation. Furthermore, operational conditions such as pH, temperature, and light intensity also play a crucial role in enhancing the degradation process. The results indicated that both high pollutant and catalyst concentrations improve the degradation rate up to a threshold, beyond which no significant benefits are observed. The optimal operational conditions were found to significantly enhance photocatalytic efficiency, with a marked increase in degradation rates under ideal settings. Antibiotics and organic dyes generally follow intricate degradation pathways, resulting in the breakdown of these substances into smaller, less detrimental compounds. On the other hand, hydrocarbons such as toluene and cyclohexane, along with nitrobenzene, may necessitate many stages to achieve complete mineralization. Several factors that affect the efficiency of degradation are the characteristics of the photocatalyst, pollutant concentration, light intensity, and the existence of co-catalysts. This approach offers a sustainable alternative for minimizing the amount of organic pollutants present in the environment, contributing to cleaner air and water. Photocatalytic degradation hence holds tremendous potential for remediation of the environment.

Recent advances and future trends in metal oxide photocatalysts for removal of pharmaceutical pollutants from wastewater: a comprehensive review

The rapid and widespread increase in pharmaceutical micropollutants (PMPs) poses a significant and immediate threat to ecosystems and human health globally. With the demand for clean water becoming increasingly critical, particularly amid escalating global water scarcity challenges, there is an urgent need for innovative approaches. Among the potential solutions, metal oxide photocatalysts such as titanium dioxide-based (TiB) and zinc oxide-based (ZnB) have garnered attention due to their cost-effectiveness, efficient photodegradation capabilities, and inherent stability. This comprehensive review explores recent advancements in the application of TiB and ZnB for the removal of PMPs from wastewater. It examines the multifaceted impacts of PMPs on environmental and public health, evaluates various techniques for their removal, and assesses design strategies aimed at maximizing the photocatalytic efficiency of TiB and ZnB. The mechanisms responsible for the photocatalytic degradation of pharmaceutical micropollutants using TiB and ZnB photocatalysts are comprehensively detailed. Finally, the review outlines the prospects and challenges associated with the use of TiB and ZnB photocatalysts for the removal of PMPs from wastewater. It emphasizes their potential to effectively mitigate PMP contaminants and make substantial contributions to sustainable water management practices in the face of escalating environmental and public health concerns.

Adsorptive-Photocatalytic Composites of α-Ferrous Oxalate Supported on Activated Carbon for the Removal of Phenol under Visible Irradiation

Adsorptive-photocatalytic composites based on activated carbon (AC) and α-ferrous oxalate dihydrate (α-FOD) were synthesized by an original two-step method and subsequently used for the removal of phenol from aqueous solutions. To obtain the composites, ferrotitaniferous black mineral sands (0.6FeTiO3·0.4Fe2O3) were first dissolved in an oxalic acid solution at ambient pressure, and further treated under hydrothermal conditions to precipitate α-FOD on the AC surface. The ratio of oxalic acid to the mineral sand precursor was tuned to obtain composites with 8.3 and 42.7 wt.% of α-FOD on the AC surface. These materials were characterized by X-ray powder diffraction, scanning electron microscopy, and the nitrogen adsorption-desorption method. The phenol removal efficiency of the composites was determined during 24 h of adsorption under dark conditions, followed by 24 h of adsorption-photocatalysis under visible light irradiation. AC/α-FOD composites with 8.3 and 42.7 wt.% of α-FOD adsorbed 60% and 51% of phenol in 24 h and reached a 90% and 96% removal efficiency after 12 h of irradiation, respectively. Given its higher photocatalytic response, the 42.7 wt.% α-FOD composite was also tested during successive cycles of adsorption and adsorption-photocatalysis. This composite exhibited a reasonable level of cyclability (~99% removal after four alternated dark/irradiated cycles of 24 h and ~68% removal after three simultaneous adsorption-photocatalysis cycles of 24 h). The promising performance of the as-prepared composites opens several opportunities for their application in the effective removal of organic micropollutants from water.

Surface modified of chitosan by TiO2@MWCNT nanohybrid for the efficient removal of organic dyes and antibiotics

Considering the increase in the discharge of industrial effluents containing dyes and antibiotic resistance as a consequence of increasing the prescription and easy distribution of antibiotic drugs at the global level, designing efficient, biodegradable and non-toxic absorbents is necessary to reduce environmental harm effects. Herein, we present a series of novel eco-friendly ternary hybrid nanocomposite hydrogels CS/TiO2@MWCNT (CTM) composed of chitosan (CS), TiO2, and multiwalled carbon nanotube (MWCNT) for removal of methylene blue (MB) and methyl orange (MO) and common antibiotic ciprofloxacin (CIP) in aqueous medium. The combination of MWCNT and TiO2 improves the physicochemical properties of CS hydrogel and increases the adsorption capacity toward pollutants in the presence of different loadings. CTM hydrogel showed a specific surface area of 236.45 m2 g-1 with a pore diameter of 7.89 nm. Adsorption mechanisms were investigated in detail using kinetic, isotherm, and thermodynamic studies of adsorption as well as various spectroscopic techniques. Adsorption of these pollutants by CTM nanocomposite hydrogel occurred using various interactions at different pHs, which showed the obvious dependence of CTM adsorption capacity on pH. Electrostatic attractions, complex formation, π-π stacking and hydrogen bonds played a key role in the adsorption process. The adsorption of MB, MO, and CIP was fitted with the Langmuir isotherm with maximum adsorption capacities of 531.91, 1763.6, and 1510.5 mg g-1, respectively. CTM had a minor decrease in adsorption strength and showed good structural stability even after 8 adsorptions-desorption cycles. The total cost of producing a 1 kg adsorbent was calculated to be $ 450, which helped us determine the economic feasibility of the adsorbent in large-scale applications.

Formulation and evaluation of azithromycin-loaded silver nanoparticles for the treatment of infected wounds

Infected wounds pose a significant challenge in healthcare, requiring innovative therapeutic strategies. Therefore, there is a critical need for innovative pharmaceutical materials to improve wound healing and combat bacterial growth. This study examined the efficacy of azithromycin-loaded silver nanoparticles (AZM-AgNPs) in treating infected wounds. AgNPs synthesized using a green method with Quinoa seed extract were loaded with AZM. Characterization techniques, including X-ray Powder Diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and Uv-Vis analysis were utilized. The agar diffusion assay and determination of the MIC were used to assess the initial antibacterial impact of the formulations on both MRSA and E. coli. In addition, the antimicrobial, wound-healing effects and histological changes following treatment with the AZM-AgNPs were assessed using an infected rat model. The nanoparticles had size of 24.9 ± 15.2 nm for AgNPs and 34.7 ± 9.7 nm for AZM-AgNPs. The Langmuir model accurately characterized the adsorption of AZM onto the AgNP surface, indicating a maximum loading capacity of 162.73 mg/g. AZM-AgNPs exhibited superior antibacterial properties in vivo and in vitro compared to controls. Using the agar diffusion technique, AZM-AgNPs showed enhanced zones of inhibition against E. coli and MRSA, which was coupled with decreased MIC levels. In addition, in vivo studies showed that AZM-AgNP treated rats had the best outcome characterized by improved healing process, lower bacterial counts and superior epithelialization, compared to the control group. In conclusion, AZM-AgNPs can be synthesized using a green method with Quinoa seed with successful loading of azithromycin onto silver nanoparticles. In vitro and in vivo studies suggest the promising use of AZM-AgNPs as an effective therapeutic agent for infected wounds.

Efficient dye adsorption of mesoporous activated carbon from bamboo parenchyma cells by phosphoric acid activation

In order to solve the environmental damage caused by the discharge of dyes as industrial wastewater, the development of efficient and sustainable adsorbents is the key, while most of the previous studies on bamboo parenchyma cells have focused on their microstructural, functional and mechanical properties, and few of the properties in adsorption have been investigated. To evaluate the role of the unique microstructure of bamboo parenchyma cells on adsorption after carbonization and activation, PC-based activated carbon (PPAC) was fabricated by the phosphoric acid activation method and tested for adsorption using methylene blue (MB). The effect of mesoporous structure on MB adsorption was investigated in detail using PPAC-30C impregnated with phosphoric acid at a concentration of 30%. The results showed that the adsorption performance was influenced by single-factor experiments (e.g., pH, activated carbon dosing). The adsorption isotherms and kinetics could conform to the Langmuir model (R2 = 0.983-0.994) and pseudo-second-order kinetic model (R2 = 0.822-0.991) respectively, and the maximum MB adsorption capacity of adsorbent was 576 mg g-1. The adsorption mechanism of MB on PPAC-30C includes physical adsorption, electrostatic attraction, hydrogen bonding, and the π-π conjugation effect, which was dominated by physical adsorption. The results of this study show that PPAC has good application prospects for cationic dye removal.

Occurrence and fate of pharmaceutical pollutants in wastewater: Insights on ecotoxicity, health risk, and state-of-the-art removal

Pharmaceutical active compound (PhAC) residues are considered an emerging micropollutant that enters the aquatic environment and causes harmful ecotoxicity. The significant sources of PhACs in the environment include the pharmaceutical industry, hospital streams, and agricultural wastes (animal husbandry). Recent investigations demonstrated that wastewater treatment plants (WWTPs) are an important source of PhACs discharging ecosystems. Several commonly reported that PhACs are detected in a range level from ng L-1 to μg L-1 concentration in WWTP effluents. These compounds can have acute and chronic adverse impacts on natural wildlife, including flora and fauna. The approaches for PhAC removals in WWTPs include bioremediation, adsorption (e.g., biochar, chitosan, and graphene), and advanced oxidation processes (AOPs). Overall, adsorption and AOPs can effectively remove PhACs from wastewater aided by oxidizing radicals. Heterogeneous photocatalysis has also proved to be a sustainable solution. Bioremediation approaches such as membrane bioreactors (MBRs), constructed wetlands (CWs), and microalgal-based systems were applied to minimize pharmaceutical pollution. Noteworthy, applying MBRs has illustrated high removal efficiencies of up to 99%, promising prospective future. However, WWTPs should be combined with advanced solutions, e.g., AOPs/photodegradation, microalgae-bacteria consortia, etc., to treat and minimize their accumulation. More effective and novel technologies (e.g., new generation bioremediation) for PhAC degradation must be investigated and specially designed for a low-cost and full-scale. Investigating green and eco-friendly PhACs with advantages, e.g., low persistence, no bioaccumulation, less or non-toxicity, and environmentally friendly, is also necessary.

Long-term effects on liver metabolism induced by ceftriaxone sodium pretreatment

Ceftriaxone is an emerging contaminant due to its potential harm, while its effects on liver are still need to be clarified. In this study, we first pretreated the 8-week-old C57BL/6J mice with high dose ceftriaxone sodium (Cef, 400 mg/mL, 0.2 mL per dose) for 8 days to prepare a gut dysbiosis model, then treated with normal feed for a two-month recovery period, and applied non-targeted metabolomics (including lipidomics) to investigate the variations of fecal and liver metabolome, and coupled with targeted determination of fecal short-chain fatty acids (SCFAs) and bile acids (BAs). Lastly, the correlations and mediation analysis between the liver metabolism and gut metabolism/microbes were carried, and the potential mechanisms of the mal-effects on gut-liver axis induced by Cef pretreatment were accordingly discussed. Compared to the control group, Cef pretreatment reduced the rate of weight gain and hepatosomatic index, induced bile duct epithelial cells proliferated around the central vein and appearance of binucleated hepatocytes, decreased the ratio of total branching chains amino acids (BCAAs) to total aromatic amino acids (AAAs) in liver metabolome. In fecal metabolome, the total fecal SCFAs and BAs did not change significantly while butyric acid decreased and the primary BAs increased after Cef pretreatment. Correlation and mediation analysis revealed one potential mechanism that Cef may first change the intestinal microbiota (such as destroying its normal structure, reducing its abundance and the stability of the microbial network or certain microbe abundance like Alistipes), and then change the intestinal metabolism (such as acetate, caproate, propionate), leading to liver metabolic disorder (such as spermidine, inosine, cinnamaldehyde). This study proved the possibility of Cef-induced liver damage, displayed the overall metabolic profile of the liver following Cef pretreatment and provided a theoretical framework for further research into the mechanism of Cef-induced liver damage.

An experimental design study of photocatalytic activity of the Z-scheme silver iodide/tungstate binary nano photocatalyst

A binary AgI/ Ag2WO4 photocatalyst was fabricated and characterized by SEM, XRD, UV-Vis DRS, and FT-IR. It was then used to photodegrade sodium ceftriaxone (CTX) in an aqueous solution. The band gap energies of 2.95, 2.78, and 2.62 eV were obtained by the Kubelka-Munk model for Ag2WO4, AgI, and AgI/Ag2WO4 catalysts. The samples have pHPZC values of 6.9, 4.2, and 6.6, respectively. The synergistic photocatalytic activity of the coupled system depended on the AgI:Ag2WO4 mole ratio and grinding time (optimums:mole ratio of 4:1 and time 30 min). The experimental design was used for optimizing the conditions and a quadratic model well-processed the data based on the model F value of 131.87 > F0.05,14,13 = 2.55 and LOF F value of 0.78 < F0.05,10,3 = 8.78. The optimized RSM run included the irradiation time of 85 min, 3.5 mg/L of CTX sample at pH 9, and a catalyst dose of 1.0 g/L. Under the optimized conditions, about 63% of CTX molecules were photodegraded. In the study of the scavenging agents, the direct Z-scheme mechanism accumulated electrons in the CB-AgI and the holes in the VB-Ag2WO4 level, as stronger reducing and oxidizing centers than the accumulated electrons and holes of the type (II) heterojunction mechanism. Compared to a CTX oxidation potential of about 0.06 V, the direct Z-scheme mechanism is more favorable to reduce or oxidize it.

A novel tungsten diselenide nanoparticles for enhanced photocatalytic performance of Cr (VI) reduction and ciprofloxacin (CIP)

Nanoparticles (NPs) fabrication is a significant approach to enhance the visible light response of photocatalysts, to realize inexpensive and more harmful compound removal, at larger scale. The poor electrons and holes separation capability and low light activity of bulk materials can be notably enhanced through developing NPs. From photocatalytic investigation, better performance was received in the tungsten diselenide (WSe2) NPs than that in bare WSe2, exhibiting the action of restrained recombination of charge carriers in the NPs. The photocatalytic Cr(VI) reduction efficiency of WSe2 NPs is 2.7 folds greater than that by bare WSe2. On the other hand, the photocatalytic efficiency follows the order of nano WSe2-3 > nano WSe2-2 > nano WSe2-1 > bare WSe2, nano WSe2-3 is nearly 2.7 folds greater than that of bare WSe2. The results imply the fabrication of WSe2 NPs and it possesses improved visible light utilization. The proposed WSe2 NPs have merged with the three aspects of photocatalytic capability including the visible light activity, the valid separation of photo-response charge carriers and enough surface active sites owing to the nanoscale formed. This research endows conduct on the potential style of NPs for photo-response water environmental remediation.

Optimizing leachate treatment with titanium oxide-impregnated activated carbon (TiO2@ASC) in a fixed-bed column: characterization, modeling, and prediction study

This research focused on the application of a fixed bed column filled with immobilized titanium oxide-loaded almond shell carbon (TiO2@ASC) for the treatment of leachate. The adsorption performance of synthesized TiO2@ASC in fixed bed column is analyzed using adsorption experiments and modeling study. The characteristics of synthesized materials are determined by several instrumental techniques like BET, XRD, FTIR, and FESEM-EDX. The flow rate, initial concentration of COD and NH3-N, and bed height were optimized to determine the effectiveness of leachate treatment. The linear bed depth service time (BDST) plots equations with a correlation coefficient of greater than 0.98 confirmed the model's accuracy for COD and NH3-N adsorption in column structure. The adsorption process was found to be well predicted by an artificial neural network (ANN) model with a root mean square error of 0.0172 and 0.0167 for COD and NH3-N reduction, respectively. The immobilized adsorbent was regenerated using HCl and was found to be reusable for up to three cycles, promoting material sustainability. This study is aimed to contribute towards SDG 6 and SDG11 by United Nations Sustainable Development Goals.

Treatment of textile wastewater using carbon-based nanomaterials as adsorbents: a review

Waste derived from the textile industry can contain a wide variety of pollutants of organic and inorganic natures, such as dyes (e.g., acid, basic, reactive, mordant dyes) and toxic metals (e.g., lead, chromium, cadmium). The presence of pollutants at high concentrations in textile waste makes them relevant sources of pollution in the environment. To solve this problem, various technologies have been developed for the removal of pollutants from these matrices. Thus, adsorption emerges as an efficient alternative for textile waste remediation, providing advantages as simplicity of operation, economy, possibility of using different adsorbent materials, and developing on-line systems that allow the reuse of the adsorbent during several adsorption/desorption cycles. This review will initially propose an introduction to the adsorption world, its fundamentals, and aspects related to kinetics, equilibrium, and thermodynamics. The possible mechanisms through which a pollutant can be retained on an adsorbent will be explained. The analytical techniques that offer valuable information to characterize the solid phases as well as each adsorbate/adsorbent system will be also commented. The most common synthesis techniques to obtain carbon nano-adsorbents have been also presented. In addition, the latest advances about the use of these adsorbents for the removal of pollutants from textile waste will be presented and discussed. The contributions reported in this manuscript demonstrated the use of highly efficient carbon-based nano-adsorbents for the removal of both organic and inorganic pollutants, reaching removal percentages from 65 to 100%.

Type-1 α-Fe2O3/TiO2 photocatalytic degradation of tetracycline from wastewater using CCD-based RSM optimization

Antibiotic pollution in water is a growing threat to public health and the environment, leading to the spread of antimicrobial-resistant bacteria. While photocatalysis has emerged as a promising technology for removing antibiotics from water, its limited efficiency in the visible light range remains a challenge. In this study, we present a novel method for the photocatalytic degradation of tetracycline, the second most commonly used antibiotic worldwide, using α-Fe₂O₃/TiO₂ nanocomposites synthesized via rapid sonochemical and wet impregnation methods. The nanocomposites were characterised and tested using a range of techniques, including BET, TEM, FTIR, XRD, FESEM, EDS, and UV-Vis. The RSM-CCD method was also used to optimize the degradation process by varying four key variables (initial concentration, photocatalyst quantity, irradiation time, and pH). The resulting optimized conditions achieved a remarkable degradation rate of 97.5%. We also investigated the mechanism of photodegradation and the reusability of the photocatalysts, as well as the effect of light source operating conditions. Overall, the results demonstrate the effectiveness of the proposed approach in degrading tetracycline in water and suggest that it may be a promising, eco-friendly technology for the treatment of water contaminated with antibiotics.

Latest avenues on titanium oxide-based nanomaterials to mitigate the pollutants and antibacterial: Recent insights, challenges, and future perspectives

Titanium oxide-based nanomaterials (TiOBNs) have been widely utilized as potential photocatalysts for various applications such as water remediation, oxidation, carbon dioxide reduction, antibacterial, food packing, etc. The benefits from TiOBNs for each application above have been determined as producing the quality of treated water, hydrogen gas as green energy, and valuable fuels. It also acts as potential material protecting foods (inactivation of bacteria and removal of ethylene) and increases shelf life for food storage. This review focuses on recent applications, challenges and future perspectives of TiOBNs to inhibit pollutants and bacteria. Firstly, the application of TiOBNs to treat emerging organic contaminants in wastewater was investigated. In particular, the photodegradation of antibiotics pollutants and ethylene using TiOBNs are described. Secondly, applying TiOBNs for antibacterial to reduce disease, disinfection, and food spoiling has been discussed. Thirdly, the photocatalytic mechanisms of TiOBNs to mitigate organic pollutants and antibacterial were determined. Finally, the challenges for different applications and future perspectives have been outlined.

Performance of Pristine versus Magnetized Orange Peels Biochar Adapted to Adsorptive Removal of Daunorubicin: Eco-Structuring, Kinetics and Equilibrium Studies

Drugs and pharmaceuticals are an emergent class of aquatic contaminants. The existence of these pollutants in aquatic bodies is currently raising escalating concerns because of their negative impact on the ecosystem. This study investigated the efficacy of two sorbents derived from orange peels (OP) biochar (OPBC) for the removal of the antineoplastic drug daunorubicin (DNB) from pharmaceutical wastewater. The adsorbents included pristine (OPBC) and magnetite (Fe₃O₄)-impregnated (MAG-OPBC) biochars. Waste-derived materials offer a sustainable and cost-effective solution to wastewater bioremediation. The results showed that impregnation with Fe₃O₄ altered the crystallization degree and increased the surface area from 6.99 m²/g in OPBC to 60.76 m²/g in the case of MAG-OPBC. Placket-Burman Design (PBD) was employed to conduct batch adsorption experiments. The removal efficiency of MAG-OPBC (98.51%) was higher compared to OPBC (86.46%). DNB adsorption onto OPBC followed the D-R isotherm, compared to the Langmuir isotherm in the case of MAG-OPBC. The maximum adsorption capacity (q_max) was 172.43 mg/g for MAG-OPBC and 83.75 mg/g for OPBC. The adsorption kinetics for both sorbents fitted well with the pseudo-second-order (PSO) model. The results indicate that MAG-OPBC is a promising adsorbent for treating pharmaceutical wastewater.

Sol-Gel Synthesis of New TiO2 Ball/Activated Carbon Photocatalyst and Its Application for Degradation of Three Hormones: 17α-EthinylEstradiol, Estrone, and β-Estradiol

Many approaches have been investigated to eliminate pharmaceuticals in wastewater treatment plants during the last decades. However, a lack of sustainable and efficient solutions exists for the removal of hormones by advanced oxidation processes. The aim of this study was to synthesize and test new photoactive bio composites for the elimination of these molecules in wastewater effluents. The new materials were obtained from the activated carbon (AC) of Arganian spinosa tree nutshells and titanium tetrachloride by the sol gel method. SEM analysis allowed one to confirm the formation of TiO₂ particles homogeneously dispersed at the surface of AC with a controlled titanium dioxide mass ratio, a specific TiO₂ anatase structure, and a highly specific surface area, evidenced by ATG, XRD, and BET analysis, respectively. The obtained composites were revealed to quantitatively absorb carbamazepine (CBZ), which is used as a referred pharmaceutical, and leading to its total elimination after 40 min under irradiation with the most effective material. TiO₂ high content disfavors CBZ adsorption but improves its degradation. In the presence of the composite, three hormones (17α-ethinylestradiol, estrone, and β-estradiol) are partially adsorbed onto the composite and totally degraded after 60 min under UV light exposure. This study constitutes a promising solution for the efficient treatment of wastewater contaminated by hormones.