Weakly Solvating Solution Enables Chemical Prelithiation of Graphite-SiOx Anodes for High-Energy Li-Ion Batteries

Novel strategies for constructing highly efficient silicon/carbon anodes: Chemical prelithiation and electrolyte post-treatment

Chemical prelithiation is an effective method to compensate for the loss of active lithium due to the formation of solid electrolyte interface, effectively addressing the issue of low initial coulombic efficiency (ICE) in silicon/carbon (Si/C) materials. Herein, the Si/C anode is prelithiated in a 1 M lithium-phenanthrene/2-methyltetrahydrofuran (Li-Phe/2-MTHF) solution in our work, and the prelithiated Si/C anode is followed by post-treatment with commercial electrolytes containing lithium difluorobis(oxalato)phosphate (LiDFBOP). The PSi/C-L0.5, originated from the reaction between residual Li-Phe/2-MTHF and the commercial electrolyte containing 0.5 wt% LiDFBOP, possesses the artificial SEI film, which not only contains a proper amount of LiF but also is rich in Li2C2O4 and Li3P. Among them, LiF and Li2C2O4 ensures the stability of the SEI film. Simultaneously, the synergistic effect of Li3P and LiF improves its Li+ transport kinetics. Therefore, the ICE of PSi/C-L0.5 reaches 92.50 %, and almost no drop in capacity occurs after 100 cycles at 0.5 A/g. Furthermore, the capacity stays steady at about 270 mAh/g through nearly 500 cycles at 1 A/g, achieving an impressive capacity retention rate of 97.8 %, significantly outperforming un-treated Si/C. This study offers new directions for constructing SEI films with stable structures and high Li+ kinetics transport.

LiC6@Li as a Promising Substitution of Li Metal Counter Electrode for Low-Temperature Battery Evaluation

Li metal, as a counter electrode, is widely used for electrode materials evaluation in coin type half-cells. However, whether this configuration is suitable for different working conditions has often been neglected. Herein, the large resistance and high cathodic/anodic over-potential of Li metal at low temperature are highlighted, revealing its incompetence as counter electrode on cryogenic condition. In view of this, a novel LiC6@Li composite electrode is developed as a promising substitution for electrode materials evaluation. In the LiC6@Li electrode, Li+ de-intercalated from LiC6 preferentially due to the low interface resistance of LiC6, presenting a cathodic/anodic over-potential of 0.05 V (67 µA cm-2) at -20 °C, which is ten times lower than that of Li metal. Moreover, the rapid lithium replenishment into LiC6 from Li metal enables a stable potential of LiC6@Li. Consequently, the LiC6@Li-based half-cells enabled more precise evaluation of the Li+ storage potential and specific capacities of a series of electrode materials at low temperature. As an extension, KC8@K is also successfully prepared as a superior counter electrode to K metal. This work proposes a suitable counter electrode for more accurately evaluating electrode materials at subfreezing scenarios, demonstrating the necessity of specialized electrode evaluation systems for particular operating conditions.

Synergistic Prelithiation and In Situ Nitrogen Doping via Li3N in SiO Anodes: A Dual-Benefit Pathway to Achieving Enhanced Li+ Kinetics and High Initial Coulombic Efficiency

Silicon monoxide (SiO) has garnered significant attention as a promising anode material for high-energy-density lithium-ion batteries due to its lower volume expansion relative to pure silicon (Si) and its higher capacity compared to graphite. Nevertheless, the poor intrinsic electronic/ionic conductivity and the low initial Coulombic efficiency (ICE) of SiO result in inferior rate capability and inadequate practical energy density, hindering its commercial viability. Here, a simultaneous prelithiation and in situ nitrogen (N) doping approach for SiO utilizing lithium nitride (Li3N), which significantly enhances both the ICE and lithium-ion (Li+) diffusion kinetics, is proposed. N atoms are not only incorporated into the carbon layer on the surface of SiO but also form a uniformly distributed amorphous Li2SiN2 phase within the SiO, facilitating Li+ transport. Molecular dynamics simulations demonstrate that the Li+ diffusion coefficient of amorphous Li2SiN2 is significantly higher than that of other crystalline phases present in the prelithiated SiO matrix. The 1.5 Ah pouch cells further validate that the SiON-0.175/graphite||NCM811 exhibits a high ICE of 88.06%, and it retains 51.5% of its capacity even under 4C fast charging conditions. This study offers new insights into the development of next-generation SiO anode materials with high ICE and high-rate performance.

Lithiophilic-Gradient, Li+ Supplementary Interphase Design for Lean Lithium Metal Batteries

The practicability of anode-less/free lithiummetal batteries (LMBs) is impeded by unregulated dendrite formation on thedeposition substrate. Herein, this study presents a lithiophilic-gradient, layer-stacked interfacial design for the lean lithium metal battery (LLMB) model. Engineered via a facile wet-chemistry approach, the high entropy metalphosphide (HEMP) particles with tunable lithiophilic species are dispersedwithin reduced graphene oxide (RGO). Moreover, a poly (vinylidene fluoride co-hexafluoropropylenepolymer) (PVDF-HFP), blended with molten Li at the tailorable amounts, forms aLi supplementary top layer through a layer-transfer printing technique. Theintegrated layer (HEMP@RGO-MTL@PH) not only regulates the dendrite-free lithiumdeposition towards the Cu substrate up to 10 mAh cm-2, but also maintains robust cyclability of the symmetric cell at 5 mA cm-2 even under 83% depth of discharge. As pairing the modified Cu foil with the LiNi0.8Mn0.1Co0.1O2 cathode (NCM811, 16.9 mg cm-2, double sided, N/P ratio of 0.21) in the 200 mAh pouch cell, achieves gravimetric energy densities of 414.7 Wh kg-1, power output of 977.1 W kg-1, as well as highly reversible phasic evolutionmonitored in operando. This gradient interfacial strategy can promotethe commercialization of energy/power-dense energy storage solutions.

A Conductive Cu-Based Metal-Organic Framework Ribbon with High-Density Redox-Active Centers as Cathode for Stable High-Capacity Lithium-Ion Batteries

Conductive Cu-based metal-organic framework (Cu-MOF) materials hold significant potential as cathodes for lithium-ion batteries (LIBs) due to their flexible structural design, high electronic conductivity, and independence from costly resources. However, their practical application is often limited by their capacity and cyclability. In this study, we report a one-dimensional Cu-MOF (DDA-Cu, DDA=1, 5-Diamino-4, 8-dihydroxy-9, 10-anthraceneedione) featuring extended π-d conjugated coordination ribbon and high-density redox-active centers, making it a stable, high-capacity cathode for LIBs. The π-d conjugated Cu-O3N motifs embedded within the ribbon not only serve as redox-active centers for enhanced lithium-ion storage capacity but also contribute to structural robustness, enabling resistance against electrode solubility in organic electrolytes, thus ensuring superior cyclability. Furthermore, these π-d conjugated Cu-O3N units promote efficient charge transfer, leading to high electronic conductivity at room temperature. These advantageous properties allow the Cu-MOF cathode to deliver a remarkable capacity (353 mAh g-1 at 0.05 A g-1) and exceptional cyclability, achieving capacity retention of 78 % after 1000 cycles, surpassing state-of-the-art MOF electrodes. Additionally, this DDA-Cu demonstrates considerable wettability with the electrolyte, achieving outstanding performance even when tested in a lean electrolyte environment (2 μL mg-1) with a high mass loading of the MOF (6.8 mg cm-2).

Pre-intercalated Sodium Ions Enhance Sodium Storage of MoS2 Anode by Mitigating Structural Dissociation

Molybdenum disulfide (MoS2) is a promising anode for sodium-ion batteries (SIBs) due to its high theoretical capacity and layered structure. However, a poor reversible conversion reaction and a low initial Coulombic efficiency (ICE) limit its practical application. This study systematically investigated the potential of pre-intercalated sodium ions molybdenum disulfide (Na-MoS2) as an anode material for SIBs. Because of the mitigation of MoS2 structural dissociation and effective replenishment of active sodium ions, Na-MoS2 delivered an outstanding capacity of 507.7 mAh g-1 after 2000 cycles at 5 A g-1, along with an ICE of 95.30%. Pre-intercalating sodium ions can expand interlayer spacing and modulate electronic structure, allowing Na-MoS2 to have greater tolerance to the electrochemical intercalation/extraction process. Furthermore, the conversion reaction of Na-MoS2 has a higher Gibbs free energy, implying its structural dissociation is thermodynamically unfavorable. This work provides a new perspective on the study of transition metal dichalcogenide electrode materials for SIBs.

External Li supply reshapes Li deficiency and lifetime limit of batteries

Lithium (Li) ions are central to the energy storing functionality of rechargeable batteries1. Present technology relies on sophisticated Li-inclusive electrode materials to provide Li ions and exactingly protect them to ensure a decent lifetime2. Li-deficient materials are thus excluded from battery design, and the battery fails when active Li ions are consumed3. Our study breaks this limit by means of a cell-level Li supply strategy. This involves externally adding an organic Li salt into an assembled cell, which decomposes during cell formation, liberating Li ions and expelling organic ligands as gases. This non-invasive and rapid process preserves cell integrity without necessitating disassembly. We leveraged machine learning to discover such functional salts and identified lithium trifluoromethanesulfinate (LiSO2CF3) with optimal electrochemical activity, potential, product formation, electrolyte solubility and specific capacity. As a proof-of-concept, we demonstrated a 3.0 V, 1,192 Wh kg-1 Li-free cathode, chromium oxide, in the anode-less cell, as well as an organic sulfurized polyacrylonitrile cathode incorporated in a 388 Wh kg-1 pouch cell with a 440-cycle life. These systems exhibit improved energy density, enhanced sustainability and reduced cost compared with conventional Li-ion batteries. Furthermore, the lifetime of commercial LiFePO4 batteries was extended by at least an order of magnitude. With repeated external Li supplies, a commercial graphite|LiFePO4 cell displayed a capacity retention of 96.0% after 11,818 cycles.

Fast-chargeable lithium-ion batteries by μ-Si anode-tailored full-cell design

Silicon (Si) anodes have long been recognized to significantly improve the energy density and fast-charging capability of lithium-ion batteries (LIBs). However, the implementation of these anodes in commercial LIB cells has progressed incrementally due to the immense volume change of Si across its full state-of-charge (SOC) range. Here, we report an anode-tailored full-cell design (ATFD), which incorporates micrometer-sized silicon (μ-Si) alone, for operation over a limited, prespecified SOC range identified as 30-70%. This range allows homogeneous (de)lithiation throughout the electrode, accompanied by an acceptable level of volume change. The ATFD-based cell exhibits 21.3% higher gravimetric energy density than that of its graphite-based counterpart in a commercial 18650 cylindrical cell and 84.6% capacity retention after 500 cycles even at a fast-charging rate of 3 C. This study indicates that the partial, intermediate SOC operation of the μ-Si anode can markedly increase the energy density and boost the fast-charging capability of a LIB cell, a challenging task in traditional cell engineering.

Molecular Engineering Chemical Pre-lithiation Reagent with Low Redox Potential for Graphite Anode Enables High Coulombic Efficiency

Graphite (Gr) is a low-cost and high-stability anode for lithium-ion batteries (LIBs). However, Gr anode exhibits an obstinate drawback of low initial Coulombic efficiency (ICE), owing to the active lithium loss for the solid electrolyte interphase (SEI) layer. Herein, a straightforward and effective chemical pre-lithiation strategy is proposed to compensate for the lithium loss. A molecular engineering phenanthrene-based lithium-arene complex (Ph-based LAC) reagent is designed by density functional theory (DFT) calculations. The engineering Ph-based reagent enhances the stability of the π-electron system and the electron-donating capacity, resulting in a reduced redox potential to facilitate lithium transfer. The electrochemical distinct of the Ph-based reagent is illustrated, the prelithiation process in a low Li-insertion platform, and the lithiation degree is controllable with the dipping time (ICE = 102%, 3 min). Notably, a denser and homogeneous SEI layer has pre-formed to enhance the Li+ transport and interface stability. Moreover, the lithium-ion full batteries assemble with LiFePO4 and NCM811 cathode, which exhibits high ICE (96.5% and 90.3%) and energy density (310 and 333 Wh kg-1). These findings present a facile and controllable pre-lithiation strategy to compensate for the lithium of LIBs, providing new valuable insights into the design and optimization of battery manufacture.

Pre-lithiation synergized with magnesiothermic reduction to enhance the performance of SiO anode for advanced lithium-ion batteries

Due to its high theoretical specific capacity, micron-sized silicon monoxide (SiO) is regarded as one of the most competitive anode materials for lithium-ion batteries with high specific energy density. However, originating from the low initial Coulombic efficiency (ICE) and large volume expansion, its large-scale application is seriously hindered. Herein, an easy-to-implement solid-state pre-lithiation method synergized with the magnesiothermic reduction process was performed to enhance the ICE of SiO and a common bimetallic hydride was used as a prelithiation reagent. Moreover, the effects of different pre-lithiation reagent amounts on the physical and electrochemical properties of SiOx are investigated. Notably, the SiOx-LA@C composite anchored by in-situ generated LiAl(SiO3)2 shows a more stable microstructure and excellent electrochemical properties, which delivers an ultrahigh ICE of 89.4 % and an excellent initial capacity of 1864.4 mAh g-1. Furthermore, the full cells were successfully assembled by using the prepared anodes, which exhibit relatively stable cycle performance over 150 cycles. This work suggests a safe and feasible route to enhance the ICE of SiOx for the applicable SiO-based anode materials.

Sequencing-Dependent Impact of Carbon Coating on Microstructure Evolution and Electrochemical Performance of Pre-lithiated SiO Anodes: Enhanced Efficiency and Stability via Pre-Coating Strategy

Silicon monoxide (SiO) has attracted considerable interest as anode material for lithium-ion batteries (LIBs). However, their poor initial Coulombic efficiency (ICE) and conductivity limit large-scale applications. Prelithiation and carbon-coating are common and effective strategies in industry for enhancing the electrochemical performance of SiO. However, the involved heat-treatment processes inevitably lead to coarsening of active silicon phases, posing a significant challenge in industrial applications. Herein, the differences in microstructures and electrochemical performances between prelithiated SiO with a pre-coated carbon layer (SiO@C@PLi) and SiO subjected to carbon-coating after prelithiation (SiO@PLi@C) are investigated. A preliminary carbon layer on the surface of SiO before prelithiation is found that can suppress active Si phase coarsening effectively and regulate the post-prelithiation phase content. The strategic optimization of the sequence where prelithiation and carbon-coating processes of SiO exert a critical influence on its regulation of microstructure and electrochemical performances. As a result, SiO@C@PLi exhibits a higher ICE of 88.0%, better cycling performance and lower electrode expansion than SiO@PLi@C. The pouch-type full-cell tests demonstrate that SiO@C@PLi/Graphite||NCM811 delivers a superior capacity retention of 91% after 500 cycles. This work provides invaluable insights into industrial productions of SiO anodes through optimizing the microstructure of SiO in prelithiation and carbon-coating processes.

Anchored Weakly-Solvated Electrolytes for High-Voltage and Low-Temperature Lithium-ion Batteries

Electrolytes endowed with high oxidation/reduction interfacial stability, fast Li-ion desolvation process and decent ionic conductivity over wide temperature region are known critical for low temperature and fast-charging performance of energy-dense batteries, yet these characteristics are rarely satisfied simultaneously. Here, we report anchored weakly-solvated electrolytes (AWSEs), that are designed by extending the chain length of polyoxymethylene ether electrolyte solvent, can achieve the above merits at moderate salt concentrations. The -O-CH2-O- segment in solvent enables the weak four-membered ring Li+ coordination structure and the increased number of segments can anchor the solvent by Li+ without largely sacrificing the ionic dissociation ability. Therefore, the single salt/single solvent AWSEs enable solvent co-intercalation-free behavior towards graphite (Gr) anode and high oxidation stability towards high-nickel cathode (LiNi0.8Co0.1Mn0.1O2-NCM811), as well as the formation of inorganic rich electrode/electrolyte interphase on both of them due to the anion-rich solvation shells. The capacity retention of Gr||NCM811 Ah-class pouch cell can reach 70.85 % for 1000 cycles at room-temperature and 75.86 % for 400 cycles at -20 °C. This work points out a promising path toward the molecular design of electrolyte solvents for high-energy/power battery systems that are adaptive for extreme conditions.

Engineering of Aromatic Naphthalene and Solvent Molecules to Optimize Chemical Prelithiation for Lithium-Ion Batteries

A cost-effective chemical prelithiation solution, which consists of Li+, polyaromatic hydrocarbon (PAH), and solvent, is developed for a model hard carbon (HC) electrode. Naphthalene and methyl-substituted naphthalene PAHs, namely 2-methylnaphthalene and 1-methylnaphthalene, are first compared. Grafting an electron-donating methyl group onto the benzene ring can decrease electron affinity and thus reduce the redox potential, which is validated by density functional theory calculations. Ethylene glycol dimethyl ether (G1), diethylene glycol dimethyl ether, and triethylene glycol dimethyl ether solvents are then compared. The G1 solution has the highest conductivity and least steric hindrance, and thus the 1-methylnaphthalene/G1 solution shows superior prelithiation capability. In addition, the effects of the interaction time between Li+ and 1-methylnaphthalene in G1 solvent on the electrochemical properties of a prelithiated HC electrode are investigated. Nuclear magnetic resonance data confirm that 10-h aging is needed to achieve a stable solution coordination state and thus optimal prelithiation efficacy. It is also found that appropriate prelithiation creates a more Li+-conducing and robust solid-electrolyte interphase, improving the rate capability and cycling stability of the HC electrode.

Beyond Mechanical Protection: The Electron-Shielding Effect of SWCNT for the Stabilized SiO Interface

The single-walled carbon nanotube (SWCNT) commonly serves as a conductive additive for SiO-based anode materials due to the excellent conductivity and mechanical properties. However, the potential action mechanisms for the SWCNT beyond conductivity and mechanical features have rarely been studied. Herein, an interfacial electron-shielding effect and preferential adsorption to the electrolyte components for the SWCNT are revealed through a series of advanced characterizations and density functional theory (DFT) simulations. It can be determined that SWCNT networks could restrict the transmission of the electron from SiO interface to electrolyte with the reduced decomposition, because of the typical axial conductivity of the SWCNT. Moreover, the SWCNT shows stronger adsorption energy for LiPF6 and ethylene carbonate (EC) molecules, rather than nonselectivity of traditional carbon additives, facilitating the generation of inorganic-rich and denser solid electrolyte interface (SEI) film. As a result, benefiting from the electron-shielding effect, preferential adsorption, and mechanical protection, the SWCNT endows the SiO@C anode with a higher average Coulombic efficiency (CE) value of 99.4% over 100 cycles and a long cycling stability.

Solution-Based Deep Prelithiation for Lithium-Ion Capacitors with High Energy Density

Lithium-ion capacitors (LICs) exhibit superior power density and cyclability compared to lithium-ion batteries. However, the low initial Coulombic efficiency (ICE) of amorphous carbon anodes (e.g., hard carbon (HC) and soft carbon (SC)) limits the energy density of LICs by underutilizing cathode capacity. Here, a solution-based deep prelithiation strategy for carbon anodes is applied using a contact-ion pair dominant solution, offering high energy density based on a systematic electrode balancing based on the cathode capacity increased beyond the original theoretical limit. Increasing the anode ICE to 150% over 100%, the activated carbon (AC) capacity is doubled by activating Li+ cation storage, which unleashes rocking-chair LIC operation alongside the dual-ion-storage mechanism. The increased AC capacity results in an energy density of 106.6 Wh kg-1 AC+SC, equivalent to 281% of that of LICs without prelithiation. Moreover, this process lowers the cathode-anode mass ratio, reducing the cell thickness by 67% without compromising the cell capacity. This solution-based deep chemical prelithiation promises high-energy LICs based on transition metal-free, earth-abundant active materials to meet the practical demands of power-intensive applications.

Direct lithium extraction from spent batteries for efficient lithium recycling

The flourishing expansion of the lithium-ion batteries (LIBs) market has led to a surge in the demand for lithium resources. Developing efficient recycling technologies for imminent large-scale retired LIBs can significantly facilitate the sustainable utilization of lithium resources. Here, we successfully extract active lithium from spent LIBs through a simple, efficient, and low-energy-consumption chemical leaching process at room temperature, using a solution comprised of polycyclic aromatic hydrocarbons and ether solvents. The mechanism of lithium extraction is elucidated by clarifying the relationship between the redox potential and extraction efficiency. More importantly, the reclaimed active lithium is directly employed to fabricate LiFePO4 cathode with performance comparable to commercial materials. When implemented in 56 Ah prismatic cells, the cells deliver stable cycling properties with a capacity retention of ∼90% after 1200 cycles. Compared with the other strategies, this technical approach shows superior economic benefits and practical promise. It is anticipated that this method may redefine the recycling paradigm for retired LIBs and drive the sustainable development of industries.

Solvent-Mediated, Reversible Ternary Graphite Intercalation Compounds for Extreme-Condition Li-Ion Batteries

Traditional Li-ion intercalation chemistry into graphite anodes exclusively utilizes the cointercalation-free or cointercalation mechanism. The latter mechanism is based on ternary graphite intercalation compounds (t-GICs), where glyme solvents were explored and proved to deliver unsatisfactory cyclability in LIBs. Herein, we report a novel intercalation mechanism, that is, in situ synthesis of t-GIC in the tetrahydrofuran (THF) electrolyte via a spontaneous, controllable reaction between binary-GIC (b-GIC) and free THF molecules during initial graphite lithiation. The spontaneous transformation from b-GIC to t-GIC, which is different from conventional cointercalation chemistry, is characterized and quantified via operando synchrotron X-ray and electrochemical analyses. The resulting t-GIC chemistry obviates the necessity for complete Li-ion desolvation, facilitating rapid kinetics and synchronous charge/discharge of graphite particles, even under high current densities. Consequently, the graphite anode demonstrates unprecedented fast charging (1 min), dendrite-free low-temperature performance, and ultralong lifetimes exceeding 10 000 cycles. Full cells coupled with a layered cathode display remarkable cycling stability upon a 15 min charging and excellent rate capability even at -40 °C. Furthermore, our chemical strategies are shown to extend beyond Li-ion batteries to encompass Na-ion and K-ion batteries, underscoring their broad applicability. Our work contributes to the advancement of graphite intercalation chemistry and presents a low-cost, adaptable approach for achieving fast-charging and low-temperature batteries.

Advancing Li-ion capacitors through dual wet chemical prelithiation

Lithium-ion batteries (LIBs) and electrical double-layer capacitors (EDLCs) are widely used in commercial energy storage systems, but each has inherent limitations. To overcome these limitations, the lithium-ion capacitor (LIC) has emerged as a hybrid energy storage device, combining the benefits of LIBs and EDLCs. However, the introduction of active lithium into LICs poses challenges due to lithium's reactivity and instability. In this study, we propose a dual wet chemical prelithiation strategy to enhance LIC performance. By wet chemically prelithiating both the activated carbon cathodes and hard carbon anodes, significant improvements are achieved compared to traditional prelithiation methods. The dual prelithiation approach outperforms electrochemical prelithiation in terms of energy storage performance, cycle life, and process simplification. LICs with dual wet chemically prelithiated electrodes demonstrate the highest energy density and retain a substantial portion of reversible capacity even at high discharge rates. The strategy exhibits fast kinetics and wide operational stability. In contrast, LICs with metallic lithium anodes or electrochemically prelithiated hard carbon anodes exhibit inferior performance and limited cycle life. The dual wet chemical prelithiation strategy represents a breakthrough in LIC technology, offering superior performance, cycle stability, and scalability. It holds promise for alkali-ion energy storage systems and drives advancements in electrochemical energy storage technology.

Harmless pre-lithiation via advantageous surface reconstruction in sacrificial cathode additives for lithium-ion batteries

Sacrificial cathode additives have emerged as a tempting strategy to compensate the initial capacity loss (ICL) in Li-ion batteries (LIBs) manufacturing. However, the utilization of sacrificial cathode additives inevitably brings residuals, side reactions, and negative impacts in which relevant researches are still in the early stage. In this study, we conduct a systematic investigation on the effects of employing a nickel-based sacrificial additive, Li2Cu0.1Ni0.9O2 (LCNO), and propose a feasible strategy to achieve advantageous surface reconstruction on LCNO. Specifically, we build a Li5AlO4 (LAO) coating layer on the LCNO through dry ball milling and annealing treatment. This process not only consumes surface residual lithium compounds on LCNO but also demonstrates minimal detrimental effects on its performance. The surface reconstructed LCNO (SR-LCNO) reveals mitigated gas generation and suppressed structure degradation under high working voltage (＞4.1 V), thereby causing negligible negative effects on the cycling capability and rate performance of commercial cathode materials. The full cells containing SR-LCNO deliver significantly improved electrochemical properties, with no observed exacerbation of side reactions. This work awakes the awareness of the prudent utilization of sacrificial cathode additives and provides an effective strategy for harmless pre-lithiation via surface reconstructed sacrificial cathode additives.

Scalable Synthesis of Bilayer Graphene at Ambient Temperature

In this work, we develop for the first time a facile chemical lithiation-assisted exfoliation approach to the controllable and scalable preparation of bilayer graphene. Biphenyl lithium (Bp-Li), a strong reducing reagent, is selected to realize the spontaneous Li-intercalation into graphite at ambient temperature, forming lithium graphite intercalation compounds (Li-GICs). The potential of Bp-Li (0.11 V vs Li/Li+), which is just lower than the potential of stage-2 lithium intercalation (0.125 V), enables the precise lithiation of graphite to stage-2 Li-GICs (LiC12). Intriguingly, the exfoliation of LiC12 leads to the bilayer-favored production of graphene, giving a high selectivity of 78%. Furthermore, the mild intercalation-exfoliation procedure yields high-quality graphene with negligible structural deterioration. The obtained graphene exhibits ultralow defect density (ID/IG ∼ 0.14) and a considerably high C/O ratio (∼29.7), superior to most current state-of-the-art techniques. This simple and scalable strategy promotes the understanding of chemical Li-intercalation methods for preparing high-quality graphene and shows great potential for layer-controlled engineering.

Facile one-pot synthesis of lithium metal nanoparticles for superior lithium-ion anode applications

A capable one-step method, femtosecond laser ablation of solids in liquids, was successfully applied to prepare lithium metal nanoparticles to mitigate the initial capacity loss and improve the electrochemical performance of a graphite-based electrode as a Li-host anode. Remarkably, according to the physicochemical characterization, this advanced optical method allowed to obtain uniform spheroidal and crystalline Li nanoparticles with an average particle size <20 nm. These novel ultrafine Li nanoparticles significantly decrease the initial capacity loss of a graphite-based anode, leading to reach high coulombic efficiency (>99 %), good specific charge capacity (322 mAh/g), and superior capacity retention (96 %) at an applied current density of 100 mA g-1 after 200 cycles.

High voltage electrolytes for lithium-ion batteries with micro-sized silicon anodes

Micro-sized silicon anodes can significantly increase the energy density of lithium-ion batteries with low cost. However, the large silicon volume changes during cycling cause cracks for both organic-inorganic interphases and silicon particles. The liquid electrolytes further penetrate the cracked silicon particles and reform the interphases, resulting in huge electrode swelling and quick capacity decay. Here we resolve these challenges by designing a high-voltage electrolyte that forms silicon-phobic interphases with weak bonding to lithium-silicon alloys. The designed electrolyte enables micro-sized silicon anodes (5 µm, 4.1 mAh cm-2) to achieve a Coulombic efficiency of 99.8% and capacity of 2175 mAh g-1 for >250 cycles and enable 100 mAh LiNi0.8Co0.15Al0.05O2 pouch full cells to deliver a high capacity of 172 mAh g-1 for 120 cycles with Coulombic efficiency of >99.9%. The high-voltage electrolytes that are capable of forming silicon-phobic interphases pave new ways for the commercialization of lithium-ion batteries using micro-sized silicon anodes.

Critical Review of Emerging Pre-metallization Technologies for Rechargeable Metal-Ion Batteries

Low Coulombic efficiency, low-capacity retention, and short cycle life are the primary challenges faced by various metal-ion batteries due to the loss of corresponding active metal. Practically, these issues can be significantly ameliorated by compensating for the loss of active metals using pre-metallization techniques. Herein, the state-of-the-art development in various pr-emetallization techniques is summarized. First, the origin of pre-metallization is elaborated and the Coulombic efficiency of different battery materials is compared. Second, different pre-metallization strategies, including direct physical contact, chemical strategies, electrochemical method, overmetallized approach, and the use of electrode additives are summarized. Third, the impact of pre-metallization on batteries, along with its role in improving Coulombic efficiency is discussed. Fourth, the various characterization techniques required for mechanistic studies in this field are outlined, from laboratory-level experiments to large scientific device. Finally, the current challenges and future opportunities of pre-metallization technology in improving Coulombic efficiency and cycle stability for various metal-ion batteries are discussed. In particular, the positive influence of pre-metallization reagents is emphasized in the anode-free battery systems. It is envisioned that this review will inspire the development of high-performance energy storage systems via the effective pre-metallization technologies.

Can We See SEI Directly by Naked Eyes?

Stable solid electrolyte interface (SEI) is the key to improve the electrochemical performance of lithium metal batteries (LMBs). However, there are still many puzzles about SEI film that have not been well explained, due to the complexity of electrochemical reactions involving in SEI formation and the absence of direct observation methods for SEI. Here, this work realizes the direct observation of SEI by skillfully designed fluorescent tracers acting as an SEI film-forming additive for electrolytes. These fluorescent tracers have three important moieties: an olefin group for polymerization on anode surface so as to participate in SEI film formation during charge/discharge cycles, a polar group for Li-ion conduction, and an AIEgen for fluorescent tracing. Therefore, the tracers participate in SEI film-forming and result in a shining SEI film. This shining SEI film with intrinsic fluorescence signal allows direct observation and quantification on the distribution, relative abundance, and macro morphology of SEI. These fluorescent tracers can also reveal the SEI formation growth destruction regularity during charge/discharge cycles. Several summarized typical macro morphologies and evolution stages of SEI will enrich knowledge and understanding of SEI and help to gain insight into the interaction between electrolyte and anode, electrochemical performance, and cycle life of batteries.

Electrolyte-assisted low-voltage decomposition of Li2C2O4 for efficient cathode pre-lithiation in lithium-ion batteries

Lithium oxalate (Li2C2O4) is an attractive cathode pre-lithiation additive for lithium-ion batteries (LIBs), but its application is hindered by its high decomposition potential (>4.7 V). Due to the liquid-solid synergistic effect of the NaNO2 additive and the LiNi0.83Co0.07Mn0.1O2 (NCM) cathode material, the decomposition efficiency of micro-Li2C2O4 reaches 100% at a low charge cutoff voltage of 4.3 V. Our work boosts the widespread practical application of Li2C2O4 by a simple and promising electrolyte-assisted cathode pre-lithiation strategy.

Unleashing the Potential of High-Capacity Anodes through an Interfacial Prelithiation Strategy

The scalable development of an environmentally adaptive and homogeneous Li+ supplementary route remains a formidable challenge for the existing prelithiation technologies, restricting the full potential of high-capacity anodes. In this study, we present a moisture-tolerant interfacial prelithiation approach through casting a hydrophobic poly(vinylidene-co-hexafluoropropylene) membrane blended with a deep-lithiated alloy (Li22Si5@C/PVDF-HFP) onto Si based anodes. This strategy could not only extend to various high-capacity anode systems (SiOx@C, hard carbon) but also align with industrial roll-to-roll assembly processes. By carefully adjusting the thickness of the prelithiation layer, the densely packed Si@C electrode (4.5 mAh cm-2) exhibits significantly improved initial Coulombic efficiency until a close-to-unit value, as well as extreme moisture tolerance (60% relative humidity). Furthermore, it achieves more than 10-fold enhancement of ionic conductivity across the electrode. As pairing the prelithiated Si@C anode with the LiNi0.8Co0.1Mn0.1O2 cathode, the 2 Ah pouch-format prototype balances an energy density of ∼371 Wh kg-1 and an extreme power output of 2450 W kg-1 as well as 83.8% capacity retention for 1000 cycles. The combined operando phase tracking and spatial arrangement analysis of the intermediate alloy elucidate that the enhanced Li utilization derives from the gradient stress dissipation model upon a spontaneous Li+ redistribution process.

Potential Controllable Redox Couple for Mild and Efficient Lithium Recovery from Spent Batteries

The prosperity of the lithium-ion battery market is dialectically accompanied by the depletion of corresponding resources and the accumulation of spent batteries. It is an urgent priority to develop green and efficient battery recycling strategies for helping ease resources and environmental pressures at the current stage. Here, we propose a mild and efficient lithium extracting strategy based on potential controllable redox couples. Active lithium in the spent battery without discharging is extracted using a series of tailored aprotic solutions comprised of polycyclic aromatic hydrocarbons and ethers. This ensures a safe yet efficient recycling process with nearly ≈100 % lithium recovery. We further investigate the Li+ -electron concerted redox reactions and the effect of solvation structure on kinetics during the extraction, and broaden the applicability of the Li-PAHs solution. This work can stimulate new inspiration for designing novel solutions to meet efficient and sustainable demands in recycling batteries.

Insights into the Effect of SiO Particle Size on the Electrochemical Performance between Half and Full Cells for Li-Ion Batteries

Silicon monoxide (SiO) has attracted growing attention as one of the most promising anodes for high-energy-density lithium-ion batteries (LIBs), benefiting from relatively low volume expansion and superior cycling performance compared to bare silicon (Si). However, the size of the SiO particle for commercial application remains uncertain. Besides, the materials and concepts developed on the laboratory level in half cells are quite different from what is necessary for practical operation in full cells. Herein, we investigate the electrochemical performance of SiO with different particle sizes between half cells and full cells. The SiO with larger particle size exhibits worse electrochemical performance in the half cell, whereas it demonstrates excellent cycling stability with a high capacity retention of 91.3% after 400 cycles in the full cell. The reasons for the differences in their electrochemical performance between half cells and full cells are further explored in detail. The SiO with larger particle size possessing superior electrochemical performance in full cells benefits from consuming less electrolyte and not being easier to aggregate. It indicates that the SiO with larger particle size is recommended for commercial application and part of the information provided from half cells may not be advocated to predict the cycling performances of the anode materials. The analysis based on the electrochemical performance of the SiO between half cells and full cells gives fundamental insight into further Si-based anode research.

Regulating the Solvation Structure of Li+ Enables Chemical Prelithiation of Silicon-Based Anodes Toward High-Energy Lithium-Ion Batteries

The solvation structure of Li+ in chemical prelithiation reagent plays a key role in improving the low initial Coulombic efficiency (ICE) and poor cycle performance of silicon-based materials. Nevertheless, the chemical prelithiation agent is difficult to dope active Li+ in silicon-based anodes because of their low working voltage and sluggish Li+ diffusion rate. By selecting the lithium-arene complex reagent with 4-methylbiphenyl as an anion ligand and 2-methyltetrahydrofuran as a solvent, the as-prepared micro-sized SiO/C anode can achieve an ICE of nearly 100%. Interestingly, the best prelithium efficiency does not correspond to the lowest redox half-potential (E1/2), and the prelithiation efficiency is determined by the specific influencing factors (E1/2, Li+ concentration, desolvation energy, and ion diffusion path). In addition, molecular dynamics simulations demonstrate that the ideal prelithiation efficiency can be achieved by choosing appropriate anion ligand and solvent to regulate the solvation structure of Li+. Furthermore, the positive effect of prelithiation on cycle performance has been verified by using an in-situ electrochemical dilatometry and solid electrolyte interphase film characterizations.

In Situ Mesopore Formation in SiOx Nanoparticles by Chemically Reinforced Heterointerface and Use of Chemical Prelithiation for Highly Reversible Lithium-Ion Battery Anode

SiO_x is a promising next-generation anode material for lithium-ion batteries. However, its commercial adoption faces challenges such as low electrical conductivity, large volume expansion during cycling, and low initial Coulombic efficiency. Herein, to overcome these limitations, an eco-friendly in situ methodology for synthesizing carbon-containing mesoporous SiO_x nanoparticles wrapped in another carbon layers is developed. The chemical reactions of vinyl-terminated silanes are designed to be confined inside the cationic surfactant-derived emulsion droplets. The polyvinylpyrrolidone-based chemical functionalization of organically modified SiO₂ nanoparticles leads to excellent dispersion stability and allows for intact hybridization with graphene oxide sheets. The formation of a chemically reinforced heterointerface enables the spontaneous generation of mesopores inside the thermally reduced SiO_x nanoparticles. The resulting mesoporous SiO_x -based nanocomposite anodes exhibit superior cycling stability (≈100% after 500 cycles at 0.5 A g^-1 ) and rate capability (554 mAh g^-1 at 2 A g^-1 ), elucidating characteristic synergetic effects in mesoporous SiO_x -based nanocomposite anodes. The practical commercialization potential with a significant enhancement in initial Coulombic efficiency through a chemical prelithiation reaction is also presented. The full cell employing the prelithiated anode demonstrated more than 2 times higher Coulombic efficiency and discharge capacity compared to the full cell with a pristine anode.

Synergistic Structure and Iron-Vacancy Engineering Realizing High Initial Coulombic Efficiency and Kinetically Accelerated Lithium Storage in Lithium Iron Oxide

Transition metal oxides with high capacity still confront the challenges of low initial coulombic efficiency (ICE, generally <70%) and inferior cyclic stability for practical lithium-storage. Herein, a hollow slender carambola-like Li_0.43 FeO_1.51 with Fe vacancies is proposed by a facile reaction of Fe³⁺ -containing metal-organic frameworks with Li₂ CO₃ . Synthesis experiments combined with synchrotron-radiation X-ray measurements identify that the hollow structure is caused by Li₂ CO₃ erosion, while the formation of Fe vacancies is resulted from insufficient lithiation process with reduced Li₂ CO₃ dosage. The optimized lithium iron oxides exhibit remarkably improved ICE (from 68.24% to 86.78%), high-rate performance (357 mAh g^-1 at 5 A g^-1 ), and superior cycling stability (884 mAh g^-1 after 500 cycles at 0.5 A g^-1 ). Paring with LiFePO₄ cathodes, the full-cells achieve extraordinary cyclic stability with 99.3% retention after 100 cycles. The improved electrochemical performances can be attributed to the synergy of structural characteristics and Fe vacancy engineering. The unique hollow structure alleviates the volume expansion of Li_0.43 FeO_1.51 , while the in situ generated Fe vacancies are powerful for modulating electronic structure with boosted Li⁺ transport rate and catalyze more Li₂ O decomposition to react with Fe in the first charge process, hence enhancing the ICE of lithium iron oxide anode materials.

Integrating Chemical Pre-Potassiation with Pre-Modulated KF-Rich Electrolyte Interfaces for Dual-Carbon Potassium Ion Hybrid Capacitor

Herein, a chemical pre-potassiation strategy via simultaneously treating both glucose derived carbon (GDC) anode and commercial activated carbon (CAC) cathode in potassium-naphthalene-tetrahydrofuran solution is developed for potassium ion hybrid capacitor (PIHC). Combined with in situ and ex situ characterizations, a radical reaction between pre-potassiation reagent and carbon electrodes is confirmed, which not only deactivates electrochemical irreversible sites, but also promotes to pre-form a uniform and dense KF-rich electrolyte film on the electrodes. As a result, the pre-potassiation treatment presents multiple advantages: (I) the initial Coulombic efficiency (CE) of the GDC anode increases from 45.4 % to 84.0 % with higher rate capability; (II) the CAC cathode exhibits the improved cycling CEs and stability due to the enhanced resistance to electrolyte oxidation at 4.2 V; (III) the assembled PIHC achieves a high energy density of 172.5 Wh kg^-1 with cycling life over 10000 cycles.

Insights into Electrolytic Pre-Lithiation: A Thorough Analysis Using Silicon Thin Film Anodes

Pre-lithiation via electrolysis, herein defined as electrolytic pre-lithiation, using cost-efficient electrolytes based on lithium chloride (LiCl), is successfully demonstrated as a proof-of-concept for enabling lithium-ion battery full-cells with high silicon content negative electrodes. An electrolyte for pre-lithiation based on γ-butyrolactone and LiCl is optimized using boron-containing additives (lithium bis(oxalato)borate, lithium difluoro(oxalate)borate) and CO₂ with respect to the formation of a protective solid electrolyte interphase (SEI) on silicon thin films as model electrodes. Reversible lithiation in Si||Li metal cells is demonstrated with Coulombic efficiencies (C_Eff ) of 95-96% for optimized electrolytes comparable to 1 m LiPF₆ /EC:EMC 3:7. Formation of an effective SEI is shown by cyclic voltammetry and X-ray photoelectron spectroscopy (XPS). electrolytic pre-lithiation experiments show that notable amounts of the gaseous product Cl₂ dissolve in the electrolyte leading to a self-discharge Cl₂ /Cl^- shuttle mechanism between the electrodes lowering pre-lithiation efficiency and causing current collector corrosion. However, no significant degradation of the Si active material and the SEI due to contact with elemental chlorine is found by SEM, impedance, and XPS. In NCM111||Si full-cells, the capacity retention in the 100th cycle can be significantly increased from 54% to 78% by electrolytic pre-lithiation, compared to reference cells without pre-lithiation of Si.

Electrolyte Design Strategies for Non-Aqueous High-Voltage Potassium-Based Batteries

High-voltage potassium-based batteries are promising alternatives for lithium-ion batteries as next-generation energy storage devices. The stability and reversibility of such systems depend largely on the properties of the corresponding electrolytes. This review first presents major challenges for high-voltage electrolytes, such as electrolyte decomposition, parasitic side reactions, and current collector corrosion. Then, the state-of-the-art modification strategies for traditional ester and ether-based organic electrolytes are scrutinized and discussed, including high concentration, localized high concentration/weakly solvating strategy, multi-ion strategy, and addition of high-voltage additives. Besides, research advances of other promising electrolyte systems, such as potassium-based ionic liquids and solid-state-electrolytes are also summarized. Finally, prospective future research directions are proposed to further enhance the oxidative stability and non-corrosiveness of electrolytes for high-voltage potassium batteries.

High Initial Coulombic Efficiency of SiO Enabled by Controlling SiO2 Matrix Crystallization

SiO is a promising anode material for practical Li-ion batteries because it can achieve a much higher capacity than graphite and a better capacity retention than Si. However, SiO suffers from poor initial Coulombic efficiency (ICE). Here, we report on a fundamentally different approach to increase the low ICE of SiO while achieving high capacity and long-term cycle stability compared to previous approaches such as electrochemical/chemical pre-lithiation processes. To enhance the ICE, the long-range/short-range orders of amorphous SiO₂ in SiO are increased by the chemical reaction of a small amount of LiOH·H₂O even at a much lower temperature (900 °C) than the reported. The increased crystallization of SiO₂ substantially reduces the irreversible electrochemical reaction of SiO. As a result, the Li-added SiO shows substantially increased ICE, ∼82.7%, which is one of the highest values. Furthermore, we demonstrate that controlling the crystallization of SiO can enable us to achieve high ICE, high reversible capacity, and superior capacity retention (∼100% at 1C rate for 100 cycles) in SiO simultaneously. The understanding and findings will pave the way to design high-capacity SiO with high ICE and long-term stability for practical high energy density Li batteries.

Weak Cation-Solvent Interactions in Ether-Based Electrolytes Stabilizing Potassium-ion Batteries

Conventional ether-based electrolytes exhibited a low polarization voltage in potassium-ion batteries, yet suffered from ion-solvent co-intercalation phenomena in a graphite anode, inferior potassium-metal performance, and limited oxidation stability. Here, we reveal that weakening the cation-solvent interactions could suppress the co-intercalation behaviour, enhance the potassium-metal performance, and improve the oxidation stability. Consequently, the graphite anode exhibits K⁺ intercalation behaviour (K||graphite cell operates 200 cycles with 86.6 % capacity retention), the potassium metal shows highly stable plating/stripping (K||Cu cell delivers 550 cycles with average Coulombic efficiency of 98.9 %) and dendrite-free (symmetric K||K cell operates over 1400 hours) properties, and the electrolyte exhibits high oxidation stability up to 4.4 V. The ion-solvent interaction tuning strategy provides a promising method to develop high-performance electrolytes and beyond.

Surface-Termination Groups’ Tuning to Improve the Lithium-Ion-Storage Performance of Ti3C2Tx MXene

Two-dimensional transition metal carbides/carbonitrides (MXenes) have broad application prospects in the field of energy storage due to their abundant surface functional groups, tunable interlayer spacing, and excellent electrical conductivity. However, the kinetics of Li-ion intercalation/deintercalation between MXene layers is slow, and the stacking between nanosheets due to long cycling reduces the structural stability and battery safety. Herein, we prepare and tune surface-termination groups of Ti3C2Tx MXene by chemical exfoliation and low-temperature annealing methods. The types of functional groups on the surface of the material are optimized by the substitution of oxygen to some -F functional groups on the surface. The optimized Ti3C2Tx MXene material exhibits a reversible lithium-ion-storage specific capacity of 444.1 mAh g−1 after 200 cycles at a current density of 0.1 A g−1. The increased of -O functional groups can increase the diffusion rate of Li+, promote the transport of electrons, and accelerate the kinetics of the electrode reaction, thereby improving the performance of lithium-ion storage.

Prelithiation Bridges the Gap for Developing Next-Generation Lithium-Ion Batteries/Capacitors

The ever-growing market of portable electronics and electric vehicles has spurred extensive research for advanced lithium-ion batteries (LIBs) with high energy density. High-capacity alloy- and conversion-type anodes are explored to replace the conventional graphite anode. However, one common issue plaguing these anodes is the large initial capacity loss caused by the solid electrolyte interface formation and other irreversible parasitic reactions, which decrease the total energy density and prevent further market integration. Prelithiation becomes indispensable to compensate for the initial capacity loss, enhance the full cell cycling performance, and bridge the gap between laboratory studies and the practical requirements of advanced LIBs. This review summarizes the various emerging anode and cathode prelithiation techniques, the key barriers, and the corresponding strategies for manufacturing-compatible and scalable prelithiation. Furthermore, prelithiation as the primary Li⁺ donor enables the safe assembly of new-configured "beyond LIBs" (e.g., Li-ion/S and Li-ion/O₂ batteries) and high power-density Li-ion capacitors (LICs). The related progress is also summarized. Finally, perspectives are suggested on the future trend of prelithiation techniques to propel the commercialization of advanced LIBs/LICs.

Elastic Lattice Enabling Reversible Tetrahedral Li Storage Sites in a High-Capacity Manganese Oxide Cathode

The key to breaking through the capacity limitation imposed by intercalation chemistry lies in the ability to harness more active sites that can reversibly accommodate more ions (e.g., Li⁺ ) and electrons within a finite space. However, excessive Li-ion insertion into the Li layer of layered cathodes results in fast performance decay due to the huge lattice change and irreversible phase transformation. In this study, an ultrahigh reversible capacity is demonstrated by a layered oxide cathode purely based on manganese. Through a wealth of characterizations, it is clarified that the presence of low-content Li₂ MnO₃ domains not only reduces the amount of irreversible O loss; but also regulates Mn migration in LiMnO₂ domains, enabling elastic lattice with high reversibility for tetrahedral sites Li-ion storage in Li layers. This work utilizes bulk cation disorder to create stable Li-ion-storage tetrahedral sites and an elastic lattice for layered materials, with a reversible capacity of 600 mA h g^-1 , demonstrated in th range 0.6-4.9 V versus Li/Li⁺ at 10 mA g^-1 . Admittedly, discharging to 0.6 V might be too low for practical use, but this exploration is still of great importance as it conceptually demonstrates the limit of Li-ions insertion into layered oxide materials.

Large areal capacity all-in-one lithium-ion battery based on boron-doped silicon/carbon hybrid anode material and cellulose framework

Si, featuring ultra-large theoretical specific capacity, is a very promising alternative to graphite for Li-ion batteries (LIBs). However, Si suffers from intrinsic low electrical conductivity and structural instability upon lithiation, thereby severely deteriorating its electrochemical performance. To address these issues, B-doping into Si, N-doped carbon coating layer, and carbon nanotube conductive network are combined in this work. The obtained Si/C hybrid anode material can be "grown" onto the Cu foil without using any binder and delivers large specific capacity (2328 mAh g^-1 at 0.2 A g^-1), great rate capability (1296.8 mAh g^-1 at 4 A g^-1), and good cyclability (76.7% capacity retention over 500 cycles). Besides, a cellulose separator derived from cotton is found to be superior to traditional polypropylene separator. By using cellulose as both the separator host and the mechanical skeleton of two electrodes, a flexible all-in-one paper-like LIB is assembled via a facile layer-by-layer filtration method. In this all-in-one LIB, all the components are integrated together with robust interfaces. This LIB is able to offer commercial-level areal capacity of 3.47 mAh cm^-2 (corresponding to 12.73 mWh cm^-2 and 318.3 mWh cm^-3) and good cycling stability even under bending. This study offers a new route for optimizing Si-based anode materials and constructing flexible energy storage devices with a large areal capacity.

Fabrication of VO Nanorings on a Porous Carbon Architecture for High-Performance Li-Ion Batteries

Vanadium monoxide (VO) is a promising candidate as an anode for lithium-ion batteries due to its high theoretical capacity, low cost, and considerable electronic conductivity. Unfortunately, a large volume change during electrochemical processes obstructs its practical application. In this work, a composite of VO nanorings grown on a porous carbon architecture is prepared via a topochemical self-reduction approach. When used as an anode for lithium-ion batteries, improved redox kinetics from enhanced electronic conduction and the corresponding fast lithium-ion diffusion is observed to greatly promote the electrochemical performance of lithium-ion batteries. The resulting composite delivered a reversible capacity of 336 mA h g^-1 after 400 cycles at 10 A g^-1 with a capacity retention of 85%, owing to the synergistic effect of VO nanorings and porous carbon in alleviating volume changes that result in a long-term cycling ability at a high current density. At 20 A g^-1, the composite anode exhibited a rate capability of 235 mA h g^-1, superior to all VO-based electrodes reported in the literature. Furthermore, a full cell was first fabricated by employing VO@C-2 as the anode and LiFePO₄ as the cathode, which exhibited a capacity of 213 mA h g^-1 after 100 cycles at 0.1 A g^-1, indicating the potential of VO as an anode for practical application.

Control of cyclic stability and volume expansion on graphite-SiO x -C hierarchical structure for Li-ion battery anodes

To increase the energy density of today's batteries, studies on adding Si-based materials to graphite have been widely conducted. However, adding a Si-based material in the slurry mixing step suffers from low distribution due to the self-aggregation property of the Si-based material. Herein, a hierarchical structure is proposed to increase the integrity by using APS to provide a bonding effect between graphite and SiO x . Additionally, to endow a protection layer, carbon is coated on the surface using the CVD method. The designed structure demonstrates enhanced integrity based on electrochemical performance. The MSG (methane decomposed SiO x @G) electrode demonstrates a high ICE of 85.6% with 429.8 mA h g-1 initial discharge capacity. In addition, the MSG anode has superior capacity retention (89.3%) after 100 cycles, with enhanced volumetric expansion (12.7%) after 50 cycles. We believe that the excellent electrochemical performance of MSG is attributed to increased integrity by using APS (3-aminopropyltrimethoxysilane) with a CVD carbon coating.

Recent Advances in Electrolytes for "Beyond Aqueous" Zinc-Ion Batteries

With the growing demands for large-scale energy storage, Zn-ion batteries (ZIBs) with distinct advantages, including resource abundance, low-cost, high-safety, and acceptable energy density, are considered as potential substitutes for Li-ion batteries. Although numerous efforts are devoted to design and develop high performance cathodes and aqueous electrolytes for ZIBs, many challenges, such as hydrogen evolution reaction, water evaporation, and liquid leakage, have greatly hindered the development of aqueous ZIBs. Developing "beyond aqueous" electrolytes can be able to avoid these issues due to the absence of water, which are beneficial for the achieving of highly efficient ZIBs. In this review, the recent development of the "beyond aqueous" electrolytes, including conventional organic electrolytes, ionic liquid, all-solid-state, quasi-solid-state electrolytes, and deep eutectic electrolytes are presented. The critical issues and the corresponding strategies of the designing of "beyond aqueous" electrolytes for ZIBs are also summarized.

Electronic Effect and Regiochemistry of Substitution in Pre-sodiation Chemistry

The low oxidation potential of a pre-sodiation cathode additive intrinsically prevents decomposition of the electrolyte. Although the introduction of electron-donating substitution reduces the oxidation potential, the additional molecular weight restricts the output capacity. Herein, as theroretically predicted, the electrochemical oxidation potential of sodium carboxylate is manipulated by the electronic effect and regiochemistry of the functionality, in which the stronger electron-donating substituent, p-π conjugation, and optimized regiochemistry can dramatically lead to the lower potential originated from the elevation of the highest occupied molecular orbital level. Thus, benefiting from the para-NH₂ unit accompanied by a conjugated aromatic architecture, molecularly engineered sodium para-aminobenzoate (PABZ-Na) presents a reduced oxidation plateau of 3.45 V. Triggered by the positive compensation merit, sodium-based electrochemical storage systems manifest excellent electrochemical performances. This breakthrough sheds light into the correlation between the electronic effect of the functional group and the oxidation potential of the organic additive, affording in-depth insights into the fundamental guidance of pre-sodiation chemistry.