Highly Efficient and Stable Dion-Jacobson Perovskite Solar Cells Enabled by Extended π-Conjugation of Organic Spacer

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells. The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs. In this work, we adopted a solid-liquid two-step film formation technique, which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films. This method possesses the advantages of integrating vapor deposition and solution methods, which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform, large-area perovskite film. Furthermore, modification of the NiOx/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization. As a result, a large-area perovskite film possessing larger grains, fewer pinholes, and reduced defects could be achieved. The inverted PSM with an active area of 61.56 cm2 (10 × 10 cm2 substrate) achieved a champion power conversion efficiency of 20.56% and significantly improved stability. This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

Dimensional Regulation from 1D/3D to 2D/3D of Perovskite Interfaces for Stable Inverted Perovskite Solar Cells

Constructing low-dimensional/three-dimensional (LD/3D) perovskite solar cells can improve efficiency and stability. However, the design and selection of LD perovskite capping materials are incredibly scarce for inverted perovskite solar cells (PSCs) because LD perovskite capping layers often favor hole extraction and impede electron extraction. Here, we develop a facile and effective strategy to modify the perovskite surface by passivating the surface defects and modulating surface electrical properties by incorporating morpholine hydriodide (MORI) and thiomorpholine hydriodide (SMORI) on the perovskite surface. Compared with the PI treatment that we previously developed, the one-dimensional (1D) perovskite capping layer derived from PI is transformed into a two-dimensional (2D) perovskite capping layer (with MORI or SMORI), achieving dimension regulation. It is shown that the 2D SMORI perovskite capping layer induces more robust surface passivation and stronger n-N homotype 2D/3D heterojunctions, achieving a p-i-n inverted solar cell with an efficiency of 24.55%, which retains 87.6% of its initial efficiency after 1500 h of operation at the maximum power point (MPP). Furthermore, 5 × 5 cm2 perovskite mini-modules are presented, achieving an active-area efficiency of 22.28%. In addition, the quantum well structure in the 2D perovskite capping layer increases the moisture resistance, suppresses ion migration, and improves PSCs' structural and environmental stability.

Manipulation of Crystal Orientation and Phase Distribution of Quasi-2D Perovskite through Synergistic Effect of Additive Doping and Spacer Engineering

The diammonium precursor 1,4-phenylenedimethanammonium (PDMA) was used as a large organic spacer for the preparation of Dion-Jacobson-type quasi-2D perovskites (PDMA)(MA)n-1PbnI3n+1 (MA = methylammonium). Films with composition ⟨n⟩ = 5 comprised randomly orientated grains and multiple microstructural domains with locally differing n values. However, by mixing the Dion-Jacobson-type spacer PDMA and the Ruddlesden-Popper-type spacer propylammonium (PA), the crystal orientation in both the vertical and the horizonal directions became regulated. High crystallinity owing to well-matched interlayer distances was observed. Combining this spacer-engineering approach with the addition of methylammonium chloride (MACl) led to full vertical alignment of the crystal orientation. Moreover, the microstructural domains at the substrate interface changed from low-n (n = 1, 2, 3) to high-n (n = 4, 5), which may be beneficial for hole extraction at the interface between perovskite and hole transport layer due to a more finely tuned band alignment. Our work sheds light on manipulating the crystallization behavior of quasi-2D perovskite and further paves the way for highly stable and efficient perovskite devices.

Functional-Group-Induced Single Quantum Well Dion-Jacobson 2D Perovskite for Efficient and Stable Inverted Perovskite Solar Cells

In two-dimensional/three-dimensional (2D/3D) perovskite heterostructure, randomly distributed multiple quantum wells (QW) 2D perovskites are frequently generated, which are detrimental to carrier transport and structural stability. Here, the high quality 2D/3D perovskite heterostructure is constructed by fabricating functional-group-induced single QW Dion-Jacobson (DJ) 2D perovskites. The utilization of ─OCH3 in the precursor solution facilitates the formation of colloidal particles with uniform size, resulting in the production of a pure 2D DJ perovskite with an n value of 3. This strategy facilitates the improvement of 3D structural stability and expedites carrier transport. The resultant devices accomplish a power conversion efficiency of 25.26% (certified 25.04%) and 23.56% at a larger area (1 cm2 ) with negligible hysteresis. The devices maintain >96% and >89% of their initial efficiency after continuous maximum power point tracking under simulated AM1.5 illumination for 1300 h and under damp-heat conditions (85 °C and 85% RH) for 1010 h, respectively.

Single-Crystal-Assisted In Situ Phase Reconstruction Enables Efficient and Stable 2D/3D Perovskite Solar Cells

Perovskite solar cells (PSCs) that incorporate both two-dimensional (2D) and three-dimensional (3D) phases possess the potential to combine the high stability of 2D PSCs with the superior efficiency of 3D PSCs. Here, we demonstrated in situ phase reconstruction of 2D/3D perovskites using a 2D perovskite single-crystal-assisted method. A gradient phase distribution of 2D RP perovskites was formed after spin-coating a solution of the 2D Ruddlesden-Popper (RP) perovskite single crystal, (DFP)2PbI4, onto the 3D perovskite surface, followed by thermal annealing. The resulting film exhibits much reduced trap density, increased carrier mobility, and superior water resistance. As a result, the optimized 2D/3D PSCs achieved a champion efficiency of 24.87% with a high open-circuit voltage (VOC) of 1.185 V. This performance surpasses the control 3D perovskite device, which achieved an efficiency of 22.43% and a VOC of 1.129 V. Importantly, the unencapsulated device demonstrates significantly enhanced operational stability, preserving over 97% of its original efficiency after continuous light irradiation for 1500 h. Moreover, the extrapolated T80 lifetimes surpass 5700 h. These findings pave the way for rational regulation of the gradient phase distribution at the interface between 2D and 3D perovskites by employing 2D RP perovskite crystals to achieve stable and efficient PSCs.

Crystal Growth Regulation of Ruddlesden-Popper Perovskites via Self-Assembly of Semiconductor Spacers for Efficient Solar Cells

The crystal growth and orientation of two-dimensional (2D) perovskite films significantly impact solar cell performance. Here, we incorporated robust quadrupole-quadrupole interactions to govern the crystal growth of 2D Ruddlesden-Popper (RP) perovskites. This was achieved through the development of two unique semiconductor spacers, namely PTMA and 5FPTMA, with different dipole moments. The ((5FPTMA)0.1 (PTMA)0.9 )2 MAn-1 Pbn I3n+1 (nominal n=5, 5F/PTMA-Pb) film shows a preferred vertical orientation, reduced grain boundaries, and released residual strain compared to (PTMA)2 MAn-1 Pbn I3n+1 (nominal n=5, PTMA-Pb), resulting in a decreased exciton binding energy and reduced electron-phonon coupling coefficients. In contrast to PTMA-Pb device with an efficiency of 15.66 %, the 5F/PTMA-Pb device achieved a champion efficiency of 18.56 %, making it among the best efficiency for 2D RP perovskite solar cells employing an MA-based semiconductor spacer. This work offers significant insights into comprehending the crystal growth process of 2D RP perovskite films through the utilization of quadrupole-quadrupole interactions between semiconductor spacers.

Orbital Interactions in 2D Dion-Jacobson Perovskites Using Oligothiophene-Based Semiconductor Spacers Enable Efficient Solar Cells

2D Dion-Jacobson (DJ) perovskites have emerged as promising photovoltaic materials, but the insulating organic spacer has hindered the efficient charge transport. Herein, we successfully synthesized a terthiophene-based semiconductor spacer, namely, 3ThDMA, for 2D DJ perovskite. An interesting finding is that the energy levels of 3ThDMA extensively overlap with the inorganic components and directly contribute to the band formation of (3ThDMA)PbI4, leading to enhanced charge transport across the organic spacer layers, whereas no such orbital interactions were found in (UDA)PbI4, a DJ perovskite based on 1,11-undecanediaminum (UDA). The devices based on (3ThDMA)MAn-1PbnI3n+1 (nominal n = 5) obtained a champion efficiency of 15.25%, which is a record efficiency for 2D DJ perovskite solar cells using long-conjugated spacers (conjugated rings ≥ 3) and a 22.60% efficiency for 3ThDMA-treated 3D PSCs. Our findings provide an important insight into understanding the orbital interactions in 2D DJ perovskite using an organic semiconductor spacer for efficient solar cells.

Enhancing Photostability of Complex Lead Halides through Modification with Antibacterial Drug Octenidine

The high power-conversion efficiencies of hybrid perovskite solar cells encourage many researchers. However, their limited photostability represents a serious obstacle to the commercialization of this promising technology. Herein, we present an efficient method for improving the intrinsic photostability of a series of commonly used perovskite material formulations such as MAPbI3, FAPbI3, Cs0.12FA0.88PbI3, and Cs0.10MA0.15FA0.75PbI3 through modification with octenidine dihydroiodide (OctI2), which is a widely used antibacterial drug with two substituted pyridyl groups and two cationic centers in its molecular framework. The most impressive stabilizing effects were observed in the case of FAPbI3 and Cs0.12FA0.88PbI3 absorbers that were manifested in significant suppression or even blocking of the undesirable perovskite films' recrystallization and other decomposition pathways upon continuous 110 mW/cm2 light exposure. The achieved material photostability-within 9000 h for the Oct(FA)n-1PbnI3n+1 (n = 40-400) and 20,000 h for Oct(Cs0.12FA0.88)n-1PbnI3n+1 (where n = 40-400) formulations-matches the highest values ever reported for complex lead halides. It is important to note that the stabilizing effect is maintained when OctI2 is used only as a perovskite surface-modifying agent. Using a two-cation perovskite composition as an example, we showed that the performances of the solar cells based on the developed Oct(Cs0.12FA0.88)399Pb400I1201 absorber material are comparable to that of the reference devices based on the unmodified perovskite composition. These findings indicate a great potential of the proposed approach in the design of new highly photostable and efficient light absorbers. We believe that the results of this study will also help to establish important guidelines for the rational material design to improve the operational stability of perovskite solar cells.

The Synergistic Effect of Additives for Formamidinium-Based Inverted Dion-Jacobson 2D Perovskite Solar Cells with Enhanced Photovoltaic Performance

Two-dimensional (2D) perovskite solar cells (PSCs) have attracted rapid growing attention due to their excellent environmental and operational stability. As an important type of 2D perovskite, Dion-Jacobson (DJ) 2D perovskites exhibit better structural integrity and more stable optoelectronic properties than those of Ruddlesden-Popper (RP) ones because of the elimination of weak van der Waals interactions. Random phase distribution, phase impurity, and weak crystallinity, however, can lead to severe nonradiative recombination losses in 2D perovskites and inferior device stability. Herein, formamidinium chloride (FACl) and lead chloride (PbCl2) are selected as additives to fabricate efficient and stable DJ 2D PSCs. The synergistic effect of additives could efficiently induce crystallization and suppress the low-n phase perovskites. The obtained 2D perovskites exhibit extended charge lifetime and enhanced charge transfer. The corresponding PSC device delivers an efficiency of 16.63% with a significantly improved open-circuit voltage (VOC) of 1.18 V and a fill factor (FF) of 81.65% than the control one. This PCE ranks the highest for inverted FA-based 2D DJ PSCs. Moreover, this device has exhibited exceptional long-term stability, which retains more than 95% of the initial efficiencies at about 50% relative humidity for 600 h.

Nucleation and Crystallization in 2D Ruddlesden-Popper Perovskites using Formamidinium-based Organic Semiconductor Spacers for Efficient Solar Cells

The conjugated organic semiconductor spacers have drawn wide attention in two-dimensional (2D) perovskites and formamidinium (FA) has been widely used as A-site cation in high-performance 3D perovskite solar cells (PSCs). However, the FA-based semiconductor spacers have rarely been investigated in 2D Ruddlesden-Popper (RP) perovskites. Here, we developed two FA-based spacers containing thieno[3,2-b]thiophene (TT) and 2,2'-bithiophene (BT) units, namely TTFA and BTFA, respectively, for 2D RP PSCs. The nucleation and crystallization kinetics of TTFA-Pb and BTFA-Pb from sol-gel to film were investigated using in situ optical microscopy and in situ grazing incidence wide-angle X-ray scattering (GIWAXS) measurements. It is found that the TTFA spacer could reduce the energy barrier of nucleation and induces crystal vertical orientation of 2D perovskite by forming larger clusters in precursor solution, resulting in much improved film quality. Benefiting from the enlarged crystal grains, reduced exciton binding energy, and decreased electron-phonon coupling coefficient, the photovoltaic device based on (TTFA)2 MAn-1 Pbn I3n+1 (n=5) achieved a champion efficiency of 19.41 %, which is a record for 2D RP PSCs with FA-based spacers. Our work provides deep understanding of the nucleation and crystallization process of 2D RP perovskite films and highlights the great potential of FA-based semiconductor spacers in highly efficient 2D PSCs.

The rise of quasi-2D Dion-Jacobson perovskites for photovoltaics

With the advance of nanotechnology, the past couple of years have witnessed the fast development of quasi two-dimensional (2D) halide perovskites, which exhibit outstanding long-term stability against moisture and heat, compared with their three-dimensional (3D) counterparts. As one of the most common structures in 2D halide perovskites, quasi-2D Dion-Jacobson (DJ) perovskites show multiple-quantum-well structures with n layers of [BX6]4- octahedral inorganic sheets sandwiched by two layers of diammonium spacers, thus exhibiting superior structural stability due to the elimination of van der Waals gaps. Thanks to the achievement of high power conversion efficiency accompanied by impressive stability, quasi-2D DJ perovskite solar cells (PSCs) have recently drawn extensive attention in the field. This review first introduces the fundamental understanding of quasi-2D DJ halide perovskites, including their superior stability, high exciton binding energy, and compositional flexibility and tunable properties. We then summarize detailed strategies to prepare high-quality quasi-2D DJ perovskites for PSCs, encompassing compositional engineering, solvent engineering, additive addition, and annealing processes. Moreover, the surface/interface modification and 2D-3D hybrid perovskite heterojunction are also discussed, for providing strategies to optimize the fabrication of quasi-2D DJ PSCs. Lastly, current challenges and perspectives toward the future development of quasi-2D DJ perovskites for photovoltaics are outlined.

Ambient-Stable 2D Dion-Jacobson Phase Tin Halide Perovskite Field-Effect Transistors with Mobility over 1.6 Cm2 V-1 s-1

Solution-processed metal halide perovskites hold immense potential for the advancement of next-generation field-effect transistors (FETs). However, the instability of perovskite-based transistors has impeded their progress and practical applications. Here, ambient-stable high-performance FETs based on 2D Dion-Jacobson phase tin halide perovskite BDASnI4 , which has high film quality and excellent electrical properties, are reported. The perovskite channels are established by engineering the film crystallization process via the employment of ammonium salt interlayers and the incorporation of NH4 SCN additives within the precursor solution. The refined FETs demonstrate field-effect hole mobilities up to 1.61 cm2 V-1 s-1 and an on/off ratio surpassing 106 . Moreover, the devices show impressive operational and environmental stability and retain their functional performance even after being exposed to ambient conditions with a temperature of 45 °C and humidity of 45% for over 150 h.

A Self-Powered UV Photodetector With Ultrahigh Responsivity Based on 2D Perovskite Ferroelectric Films With Mixed Spacer Cations

Self-powered photodetectors (PDs) have the advantages of no external power requirement, wireless operation, and long life. Spontaneous ferroelectric polarizations can significantly increase built-in electric field intensity, showing great potential in self-powered photodetection. Moreover, ferroelectrics possess pyroelectric and piezoelectric properties, beneficial for enhancing self-powered PDs. 2D metal halide perovskites (MHPs), which have ferroelectric properties, are suitable for fabricating high-performance self-powered PDs. However, the research on 2D metal halide perovskites ferroelectrics focuses on growing bulk crystals. Herein, 2D ferroelectric perovskite films with mixed spacer cations for self-powered PDs are demonstrated by mixing Ruddlesden-Popper (RP)-type and Dion-Jacobson (DJ)-type perovskite. The (BDA0.7 (BA2 )0.3 )(EA)2 Pb3 Br10 film possesses, overall, the best film qualities with the best crystalline quality, lowest trap density, good phase purity, and obvious ferroelectricity. Based on the ferro-pyro-phototronic effect, the PD at 360 nm exhibits excellent photoelectric properties, with an ultrahigh peak responsivity greater than 93 A W-1 and a detectivity of 2.5 × 1015 Jones, together with excellent reproducibility and stability. The maximum responsivities can be modulated by piezo-phototronic effect with an effective enhancement ratio of 480%. This work will open up a new route of designing MHP ferroelectric films for high-performance PDs and offers the opportunity to utilize it for various optoelectronics applications.

Layered Low-Dimensional Ruddlesden-Popper and Dion-Jacobson Perovskites: From Material Properties to Photovoltaic Device Performance

Layered low-dimensional halide perovskites (LDPs) with multiple quantum well structure have shown increasing research interest in photovoltaic solar cell applications owing to their intrinsic moisture stability and favorable photophysical properties in comparison with their three-dimensional (3D) counterparts. The most common LDPs are Ruddlesden-Popper (RP) phases and Dion-Jacobson (DJ) phases, both of which have made significant research advances in efficiency and stability. However, distinct interlayer cations between RP and DJ phase lead to disparate chemical bonds and different perovskite structures, which endow RP and DJ perovskite with distinctive chemical and physical properties. Plenty of reviews have reported the research progress of LDPs but no summary has elaborated from the perspective of the merits and drawbacks of the RP and DJ phases. Herein, in this review, we offer a comprehensive expound on the merits and promises of RP and DJ LDPs from their chemical structure, physicochemical properties, and photovoltaic performance research progress aiming to provide a new insight into the dominance of RP and DJ phases. Then, we reviewed the recent progress on the synthesis and implementation of RP and DJ LDPs thin films and devices, as well as their optoelectronic properties. Finally, we discussed the possible strategies to resolve existing toughs to realize the desired high-performance LDPs solar cells.

Selenophene-Based 2D Ruddlesden-Popper Perovskite Solar Cells with an Efficiency Exceeding 19

Two-dimensional (2D) Ruddlesden-Popper (RP) perovskites have emerged as attractive candidates for high-performance perovskite solar cells (PSCs) thanks to their superior environmental and structural stability. However, 2D RP PSCs exhibit larger exciton binding energy due to the dielectric mismatch between the organic and inorganic layers, resulting in poorer photovoltaic performance compared to their 3D analogs. Here, we developed a selenophene-based spacer, namely, 2-selenophenemethylammonium (SeMA), for stable and efficient 2D RP PSCs. The 2D perovskite film using methylammonium (MA) as the A-site cation (nominal n = 5) shows excellent film quality with large grain size and a preferred vertical orientation relative to the substrate. Furthermore, we have successfully demonstrated the effectiveness of a predeposition transport layer (PDTL) consisting of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) in passivating surface defects of the perovskite film and inducing densification of the upper PCBM electron transport layer. This densification promotes efficient extraction and transport of electrons. The optimized PSCs based on 2D RP perovskite using MA as A-site cation (nominal n = 5) achieved a power conversion efficiency (PCE) of 17.25%, which was further boosted to 19.03% when using formamidinium (FA) as A-site cation. This represents a record PCE of 2D RP PSCs by using the selenophene-based spacer. Moreover, these 2D RP PSCs significantly improve thermal, moisture, and light stability. Our results provide significant implications for the synergistic strategy of developing selenophene-based spacers and device engineering methods for achieving highly efficient and stable 2D RP perovskite solar cells.

Crystallinity and Phase Control in Formamidinium-Based Dion-Jacobson 2D Perovskite via Seed-Induced Growth for Efficient Photovoltaics

2D perovskites based on Formamidinium (FA) hold the potential for excellent stability and a broad absorption range, making them attractive materials for solar cells. However, FA-based 2D perovskites produced via one-step processing exhibit poor crystallinity and random quasi-quantum wells (QWs), leading to subpar photovoltaic performance. In this study, a seed-induced growth approach is introduced employing MAPbCl3 and BDAPbI4 in the deposition of FA-based Dion-Jacobson 2D perovskite films. This method yields high-quality perovskite films as the seeds preferentially precipitate and serve as templates for the epitaxial growth of FA-based counterparts, effectively suppressing the δ phase. Moreover, the epitaxial growth facilitated by uniformly dispersed seeds results in simultaneous crystallization from top to bottom, efficiently mitigating random phases (n = 2, 3, 4…) induced by the diffusion of organic cations and, in turn, minimizing energy loss. The impact of seed-induced growth on the crystallization and phase distribution of FA-based 2D perovskites is systematically investigated. As a result, the optimized FA-based 2D perovskite solar cell delivers an outstanding efficiency of 20.0%, accompanied by a remarkable fill factor of 0.823. Additionally, the unencapsulated device demonstrates exceptional stability, maintaining 98% of its initial efficiency after 1344 h of storage.

Target Therapy for Buried Interface Enables Stable Perovskite Solar Cells with 25.05% Efficiency

The buried interface in perovskite solar cells (PSCs) is pivotal for achieving high efficiency and stability. However, it is challenging to study and optimize the buried interface due to its non-exposed feature. Here, a facile and effective strategy is developed to modify the SnO2 /perovskite buried interface by passivating the buried defects in perovskite and modulating carrier dynamics via incorporating formamidine oxalate (FOA) in SnO2 nanoparticles. Both formamidinium and oxalate ions show a longitudinal gradient distribution in the SnO2 layer, mainly accumulating at the SnO2 /perovskite buried interface, which enables high-quality upper perovskite films, minimized defects, superior interface contacts, and matched energy levels between perovskite and SnO2 . Significantly, FOA can simultaneously reduce the oxygen vacancies and tin interstitial defects on the SnO2 surface and the FA+ /Pb2+ associated defects at the perovskite buried interface. Consequently, the FOA treatment significantly improves the efficiency of the PSCs from 22.40% to 25.05% and their storage- and photo-stability. This method provides an effective target therapy of buried interface in PSCs to achieve very high efficiency and stability.

Recent Progress of Layered Perovskite Solar Cells Incorporating Aromatic Spacers

Layered two dimensional (2D) or quasi-2D perovskites are emerging photovoltaic materials due to their superior environment and structure stability in comparison with their 3D counterparts. The typical 2D perovskites can be obtained by cutting 3D perovskites along  < 100 >  orientation by incorporation of bulky organic spacers, which play a key role in the performance of 2D perovskite solar cells (PSCs). Compared with aliphatic spacers, aromatic spacers with high dielectric constant have the potential to decrease the dielectric and quantum confinement effect of 2D perovskites, promote efficient charge transport and reduce the exciton binding energy, all of which are beneficial for the photovoltaic performance of 2D PSCs. In this review, we aim to provide useful guidelines for the design of aromatic spacers for 2D perovskites. We systematically reviewed the recent progress of aromatic spacers used in 2D PSCs. Finally, we propose the possible design strategies for aromatic spacers that may lead to more efficient and stable 2D PSCs.

Moisture-Tailored 2D Dion-Jacobson Perovskites for Reconfigurable Optoelectronics

Humidity- and moisture-induced degradation has been a longstanding problem in perovskite materials, affecting their long-term stability during applications. Counterintuitively, the moisture is leveraged to tailor the reversible hydrochromic behaviors of a new series of 2D Dion-Jacobson (DJ) perovskites for reconfigurable optoelectronics. In particular, the hydrogen bonds between organic cations and water molecules can be dynamically modulated via moisture removal/exposure. Remarkably, such modulation confines the movement of the organic cations close to the original position, preventing their escape from crystal lattices. Furthermore, this mechanism is elucidated by theoretical analysis using first-principles calculations and confirmed with the experimental characterizations. The reversible fluorescent transition 2D DJ perovskites show excellent cyclical properties, presenting untapped opportunities for reconfigurable optoelectronic applications. As a proof-of-concept demonstration, an anti-counterfeiting display is shown based on patterned reversible 2D DJ perovskites. The results represent a new avenue of reconfigurable optoelectronic application with 2D DJ perovskites for humidity detection, anti-counterfeiting, sensing, and other emerging photoelectric intelligent technologies.

Additive Engineering for Stable and Efficient Dion-Jacobson Phase Perovskite Solar Cells

Because of their better chemical stability and fascinating anisotropic characteristics, Dion-Jacobson (DJ)-layered halide perovskites, which owe crystallographic two-dimensional structures, have fascinated growing attention for solar devices. DJ-layered halide perovskites have special structural and photoelectronic features that allow the van der Waals gap to be eliminated or reduced. DJ-layered halide perovskites have improved photophysical characteristics, resulting in improved photovoltaic performance. Nevertheless, owing to the nature of the solution procedure and the fast crystal development of DJ perovskite thin layers, the precursor compositions and processing circumstances can cause a variety of defects to occur. The application of additives can impact DJ perovskite crystallization and film generation, trap passivation in the bulk and/or at the surface, interface structure, and energetic tuning. This study discusses recent developments in additive engineering for DJ multilayer halide perovskite film production. Several additive-assisted bulk and interface optimization methodologies are summarized. Lastly, an overview of research developments in additive engineering in the production of DJ-layered halide perovskite solar cells is offered.

Highly Efficient and Stable FA-Based Quasi-2D Ruddlesden-Popper Perovskite Solar Cells by the Incorporation of β-Fluorophenylethanamine Cations

2D Ruddlesden-Popper (2D RP) perovskite, with attractive environmental and structural stability, has shown great application in perovskite solar cells (PSCs). However, the relatively inferior photovoltaic efficiencies of 2D PSCs limit their further application. To address this issue, β-​fluorophenylethanamine (β-​FPEA) as a novel spacer cation is designed and employed to develop stable and efficient quasi-2D RP PSCs. The strong dipole moment of the β-​FPEA enhances the interactions between the cations and [PbI₆ ]^4- octahedra, thus improving the charge dissociation of quasi-2D RP perovskite. Additionally, the introduction of the β-​FPEA cation optimizes the energy level alignment, improves the crystallinity, stabilizes both the mixed phase and a-FAPbI₃ phase of the quasi-2D RP perovskite film, prolongs the carrier diffusion length, increases the carrier lifetime and decreases the trap density. By incorporating the β-​FPEA, the quasi-2D RP PSCs exhibit a power conversion efficiency (PCE) of 16.77% (vs phenylethylammonium (PEA)-based quasi-2D RP PSCs of 12.81%) on PEDOT:PSS substrate and achieve a champion PCE of 19.11% on the PTAA substrate. It is worth noting that the unencapsulated β-​FPEA-based quasi-2D RP PSCs exhibit considerably improved thermal and moisture stability. These findings provide an effective strategy for developing novel spacer cations for high-performance 2D RP PSCs.

Rapid Interlayer Charge Separation and Extended Carrier Lifetimes due to Spontaneous Symmetry Breaking in Organic and Mixed Organic-Inorganic Dion-Jacobson Perovskites

Promising alternatives to three-dimensional perovskites, two-dimensional (2D) layered metal halide perovskites have proven their potential in optoelectronic applications due to improved photo- and chemical stability. Nevertheless, photovoltaic devices based on 2D perovskites suffer from poor efficiency owing to unfavorable charge carrier dynamics and energy losses. Focusing on the 2D Dion-Jacobson perovskite phase that is rapidly rising in popularity, we demonstrate that doping of complementary cations into the 3-(aminomethyl)piperidinium perovskite accelerates spontaneous charge separation and slows down charge recombination, both factors improving the photovoltaic performance. Employing ab initio nonadiabatic (NA) molecular dynamics combined with time-dependent density functional theory, we demonstrate that cesium doping broadens the bandgap by 0.4 eV and breaks structural symmetry. Assisted by thermal fluctuations, the symmetry breaking helps to localize electrons and holes in different layers and activates additional vibrational modes. As a result, the charge separation is accelerated. Simultaneously, the charge carrier lifetime grows due to shortened coherence time between the ground and excited states. The established relationships between perovskite composition and charge carrier dynamics provide guidelines toward future material discovery and design of perovskite solar cells.

Recent progress in layered metal halide perovskites for solar cells, photodetectors, and field-effect transistors

Metal halide perovskite materials demonstrate immense potential for photovoltaic and electronic applications. In particular, two-dimensional (2D) layered metal halide perovskites have advantages over their 3D counterparts in optoelectronic applications due to their outstanding stability, structural flexibility with a tunable bandgap, and electronic confinement effect. This review article first analyzes the crystallography of different 2D perovskite phases [the Ruddlesden-Popper (RP) phase, the Dion-Jacobson (DJ) phase, and the alternating cations in the interlayer space (ACI) phase] at the molecular level and compares their common electronic properties, such as out-of-plane conductivity, crucial to vertical devices. This paper then critically reviews the recent development of optoelectronic devices, namely solar cells, photodetectors and field effect transistors, based on layered 2D perovskite materials and points out their limitations and potential compared to their 3D counterparts. It also identifies the important application-specific future research directions for different optoelectronic devices providing a comprehensive view guiding new research directions in this field.

Stabile fluoro-benzene-based spacer for lead-free Dion-Jacobson perovskites

Two-dimensional perovskite materials have been investigated as potential candidates for next-generation-wide band gap devices and lead-based perovskites are the most common materials within two-and three-dimensional structures due to their superior optoelectronic properties. Nevertheless, the stability and toxic element issues are the two significant shortcomings of device commercialization. The fluoro-benzene-based divalent ammonium spacer cations and replacing Zn²⁺ with Pb²⁺ will improve the two-dimensional perovskite stability. These stable lead-free wide band gap two-dimensional structures have better carrier mobility at high-temperature regions. Therefore, lead-free two-dimensional perovskites might be suitable for higher temperatures optoelectronic applications.

Orbital Interactions between the Organic Semiconductor Spacer and the Inorganic Layer in Dion-Jacobson Perovskites Enable Efficient Solar Cells

2D Dion-Jacobson (DJ) perovskites have become emerging photovoltaic materials owing to their intrinsic structure stability. However, as insulating aliphatic cations are widely used as spacers, the interactions between the spacers and inorganic layers in DJ perovskites have rarely been studied. Here, an organic semiconductor spacer with two covalently connected thiophene rings, namely bithiophene dimethylammonium (BThDMA), is successfully developed for 2D DJ perovskite solar cells (PSCs). An important finding is that there are strong orbital interactions between the conjugated organic spacer and adjacent inorganic layers, whereas no such interactions exist in DJ perovskite using an aliphatic octane-1,8-diaminium (ODA) spacer with similar length. The BThDMA spacer with multiple conjugated aromatic rings can also induce crystal growth with large grain size and preferred vertical orientation, resulting in reduced trap density and improved charge-carrier mobility. As a result, the optimized device based on (BThDMA)MA_{n -1} Pb_n I_{3 n +1} (nominal n = 5) shows an excellent PCE of 18.1% with negligible hysteresis, which is a record efficiency for 2D DJ PSCs using a spacer with two or more covalently linked aromatic rings. These findings provide a novel and important insight on achieving efficient and stable 2D DJ perovskite solar cells by developing organic semiconductor spacers.

Solvent Effect on Film Formation and Trap States of Two-Dimensional Dion-Jacobson Perovskite

Two dimensional Dion-Jacobson (2D DJ) perovskite has emerged as a potential photovoltaic material because of its unique optoelectronic characteristics. However, due to its low structural flexibility and high formation energy, extra assistance is needed during crystallization. Herein, we study the solvent effect on film formation and trap states of 2D DJ perovskite. It is found that the nucleation process of 2D DJ perovskite can be retarded by extra coordination, which is proved by in situ optical spectra. As a benefit, out-of-plane oriented crystallization and ordered phase distribution are realized. Finally, in 1,5-pentanediammonium (PeDA) based 2D DJ perovskite solar cells (PSCs), one of the highest reported open-circuit voltage (V_OC) values of 1.25 V with state-of-the-art efficiency of 18.41% is obtained due to greatly shallowed trap states and suppressed nonradiative recombination. The device also exhibits excellent heat tolerance, which maintains 80% of its initial efficiency after being kept under 85 °C after 3000 h.

Novel PHA Organic Spacer Increases Interlayer Interactions for High Efficiency in 2D Ruddlesden-Popper CsPbI3 Solar Cells

The two-dimensional (2D) Ruddlesden-Popper (RP) CsPbI₃ with hydrophobic organic spacers can significantly improve the environmental and phase stability of photovoltaic devices by suppressing ion migration and inducing steric hindrance. However, due to the multiple-quantum-well structure, these spacer cations lead to weak interactions in 2D RP CsPbI₃, which seriously affect the carrier transport. Here, a novel N-H-group-rich phenylhydrazine spacer, namely, PHA, was developed for 2D RP CsPbI₃ perovskite solar cells (PSCs). A series of characterizations confirm that the 2D perovskites using PHA spacers enhanced the N-H···I hydrogen-bonding interaction between the organic spacer cations and the [PbI₆]^4- inorganic layer and accelerated the crystallization rate of the perovskite film, which was beneficial to the preparation of high-quality films with preferred vertical orientation, large grain size, and dense morphology. Meanwhile, the trap state density of the as-prepared 2D RP perovskite films is significantly reduced to enable efficient charge carrier transport. As a result, the (PHA)₂Cs₄Pb₅I₁₆ PSCs achieved a performance of 16.23% with good environmental stability. This work provides a simple organic spacer selection scheme to realize interaction optimization in 2D RP CsPbI₃ to develop efficient and stable PSCs.

Recognizing the Importance of Fast Nonisothermal Crystallization for High-Performance Two-Dimensional Dion-Jacobson Perovskite Solar Cells with High Fill Factors: A Comprehensive Mechanistic Study

Two-dimensional (2D) Dion-Jacobson (DJ) perovskite solar cells (PSCs), despite their advantage in versatility of n-layer variation, are subject to poor photovoltaic efficiency, particularly in the fill factor (FF), compared to their three-dimensional counterparts. To enhance the performance of DJ PSCs, the process of growing crystals and hence the corresponding morphology of DJ perovskites are of prime importance. Herein, we report the fast nonisothermal (NIT) crystallization protocol that is previously unrecognized for 2D perovskites to significantly improve the morphology, orientation, and charge transport of the DJ perovskite films. Comprehensive mechanistic studies reveal that the NIT effect leads to the secondary crystallization stage, forming network-like channels that play a vital role in the FF's leap-forward improvement and hence the DJ PSC's performance. As a whole, the NIT crystallized PSCs demonstrate a high power conversion efficiency and an FF of up to 19.87 and 86.16%, respectively. This research thus provides new perspectives to achieve highly efficient DJ PSCs.

An organic-halide perovskite-based photo-assisted Li-ion battery for photoelectrochemical storage

Merging solar energy conversion and storage into a single device would improve the utilization of solar energy. Within such a device, the photoelectrochemical material is crucially important. Herein, we design a hybrid perovskite (DAPbI) that exhibits the favorable properties of fast charge transfer and CO redox sites for steady and reversible Li⁺ de/intercalation, and it can be used as a bifunctional cathode for an efficient photoinduced lithium-ion battery (LIB). The enhanced charge carrier lifetime of DAPbI (τ_CS/CR = 452.1/3905 ps, compared to the organic cation DAAQ where τ_CS/CR = 335.7/1291 ps) for solar harvesting and conversion and its abundant reversible redox activity for energy storage lay the foundations for efficient photoelectrochemical energy conversion and storage. Using DAPbI as a cathode, an integrated photo-assisted LIB is realized, with a 0.2 V reduction in charge voltage, a 0.1 V increase in discharge voltage, enhancements of 7.4% in roundtrip efficiency and 0.5% in photoelectrochemical energy storage efficiency, and an 11.3% reduction in input power and an 18% increase in output power. This work provides a direct and sustainable strategy to utilize solar energy through electrochemical energy storage, which may support prosperous developments in this domain.

2D Material and Perovskite Heterostructure for Optoelectronic Applications

Optoelectronic devices are key building blocks for sustainable energy, imaging applications, and optical communications in modern society. Two-dimensional materials and perovskites have been considered promising candidates in this research area due to their fascinating material properties. Despite the significant progress achieved in the past decades, challenges still remain to further improve the performance of devices based on 2D materials or perovskites and to solve stability issues for their reliability. Recently, a novel concept of 2D material/perovskite heterostructure has demonstrated remarkable achievements by taking advantage of both materials. The diverse fabrication techniques and large families of 2D materials and perovskites open up great opportunities for structure modification, interface engineering, and composition tuning in state-of-the-art optoelectronics. In this review, we present comprehensive information on the synthesis methods, material properties of 2D materials and perovskites, and the research progress of optoelectronic devices, particularly solar cells and photodetectors which are based on 2D materials, perovskites, and 2D material/perovskite heterostructures with future perspectives.

Nanosegregation in arene-perfluoroarene π-systems for hybrid layered Dion-Jacobson perovskites

Layered hybrid perovskites are based on organic spacers separating hybrid perovskite slabs. We employ arene and perfluoroarene moieties based on 1,4-phenylenedimethylammonium (PDMA) and its perfluorinated analogue (F-PDMA) in the assembly of hybrid layered Dion-Jacobson perovskite phases. The resulting materials are investigated by X-ray diffraction, UV-vis absorption, photoluminescence, and solid-state NMR spectroscopy to demonstrate the formation of layered perovskite phases. Moreover, their behaviour was probed in humid environments to reveal nanoscale segregation of layered perovskite species based on PDMA and F-PDMA components, along with enhanced stabilities of perfluoroarene systems, which is relevant to their application.

Ordered Element Distributed C3 N Quantum Dots Manipulated Crystallization Kinetics for 2D CsPbI3 Solar Cells with Ultra-High Performance

Two-dimensional (2D) CsPbI₃ is developed to conquer the phase-stability problem of CsPbI₃ by introducing bulky organic cations to produce a steric hindrance effect. However, organic cations also inevitably increase the formation energy and difficulty in crystallization kinetics regulation. Such poor crystallization process modulation of 2D CsPbI₃ leads to disordered phase-arrangement, which impedes the transport of photo-generated carriers and worsens device performance. Herein, a type of C₃ N quantum dots (QDs) with ordered carbon and nitrogen atoms to manipulate the crystallization process of 2D CsPbI₃ for improving the crystallization pathway, phase-arrangement and morphology, is introduced. Combination analyses of theoretical simulation, morphology regulation and femtosecond transient absorption (fs-TA) characterization, show that the C₃ N QDs induce the formation of electron-rich regions to adsorb bulky organic cations and provide nucleation sites to realize a bi-directional crystallization process. Meanwhile, the quality of 2D CsPbI₃ film is improved with lower trap density, higher surface potential, and compact morphology. As a result, the power conversion efficiency (PCE) of the optimized device (n = 5) boosts to an ultra-high value of 15.63% with strengthened environmental stability. Moreover, the simple C₃ N QDs insertion method shows good universality to other bulky organic cations of Ruddlesden-Popper and Dion-Jacobson, providing a good modulation strategy for other optoelectronic devices.

Insight into the Enhanced Charge Transport in Quasi-2D Perovskite via Fluorination of Ammonium Cations for Photovoltaic Applications

Fluorinated spacer cations in quasi-2D (Q-2D) perovskites have recently been demonstrated to improve the Q-2D perovskite solar cell (PSC) performance. However, the underlying mechanism of fluorination of organic cations on the improvement is still unclear. Here, using fluorinated benzylammonium (named F-BZA) as a spacer cation in Q-2D Ruddlesden-Popper (RP) perovskites, we deeply investigate the effect of fluorination of organic cations on perovskite crystallization and intermolecular interactions for improving the charge transport and device performance. It is found that fluorination of spacer cations can slow down the crystallization rate of perovskites, resulting in vertically aligned large grains. Moreover, the interaction between the adjacent spacer cations is further enhanced, constructing a new faster charge-transport channel with a lifetime of 77 ps. Accordingly, the carrier mobility is improved by an order of magnitude and a power conversion efficiency (PCE) of 16.82% is achieved in much more stable F-BZA-based Q-2D RP PSCs, 35% higher than that of BZA-based devices (12.39%). Our results elucidate the mechanism and its importance of fluorinating spacer cations for high-performance Q-2D PSC development.