Dye and its removal from aqueous solution by adsorption: a review

Recyclable chitosan adsorbent: Facile functionalization strategy, excellent removal capacity of dyes and adsorption mechanism

The development of chitosan-based adsorbents with facile preparation, high adsorption performance and reusability for the removal of contaminant dyes remains a persistent challenge. To overcome this challenge, herein, we have developed a novel and extremely facile one-step strategy by which a new high-performance chitosan/polyethyleneimine/polyethylene glycol diglycidyl ether adsorbent (named as CC/PEI/PGDE) has been successfully fabricated via direct functionalization of CC by PEI at ambient temperature followed by subsequent freeze-drying. The Box-Behnken Design was employed to optimize the concentrations of adsorbent components. Attractively, this adsorbent exhibit outstanding adsorption performances to congo red (RED), acid blue-25 (BLUE) and amino black-10B (BLACK) with 2901 mg g-1 (90.9 %), 3434 mg g-1 (90.9 %), and 1438 mg g-1 (90.1 %) of adsorption capacities (removal efficiencies), respectively, and maintains nearly the same adsorption behaviors to original adsorbent even after 6 cycles of adsorption-desorption processes. Meanwhile, three kinetic models, three isothermal models, and the Vant Hoff model are employed to further investigate the adsorption behaviors of RED, BLUE, and BLACK dyes by CC/PEI/PGDE. The results from SEM, EDS, BET, FT-IR, pHZPC and XPS confirm that hydrogen bond interactions and electrostatic attractions play crucial roles in facilitating dyes adsorption by CC/PEI/PGDE. It is expected that this work can bring forward a new perspective for the facile design of high-performance adsorbent for removing anionic dyes from wastewater.

Biopolymer-based beads for the adsorptive removal of organic pollutants from wastewater: Current state and future perspectives

Among biopolymer-based adsorbents, composites in the form of beads have shown promising results in terms of high adsorption capacity and ease of separation from the effluents. This review addresses the potential of biopolymer-based beads to remediate wastewaters polluted with emerging organic contaminants, for instance dyes, active pharmaceutical ingredients, pesticides, phenols, oils, polyaromatic hydrocarbons, and polychlorinated biphenyls. High adsorption capacities up to 2541.76 mg g-1 for dyes, 392 mg g-1 for pesticides and phenols, 1890.3 mg g-1 for pharmaceuticals, and 537 g g-1 for oils and organic solvents have been reported. The review also attempted to convey to its readers the significance of wastewater treatment through adsorption by providing an overview on decontamination technologies of organic water contaminants. Various preparation methods of biopolymer-based gel beads and adsorption mechanisms involved in the process of decontamination have been summarized and analyzed. Therefore, we believe there is an urge to discuss the current state of the application of biopolymer-based gel beads for the adsorption of organic pollutants from wastewater and future perspectives in this regard since it is imperative to treat wastewater before releasing into freshwater bodies.

Synthesis of carboxymethyl starch co (polyacrylamide/ polyacrylic acid) hydrogel for removing methylene blue dye from aqueous solution

Natural polysaccharides, notably starch, have garnered attention for their accessibility, cost-effectiveness, and biodegradability. Modifying starch to carboxymethyl starch enhances its solubility, swelling capacity, and adsorption efficiency. This research examines the synthesis of an effective hydrogel adsorbent based on carboxymethyl starch for the elimination of methylene blue from aqueous solutions. The hydrogel was synthesized using polyacrylamide and polyacrylic acid as monomers, ammonium persulfate as the initiator, and N,N'-methylenebisacrylamide as the cross-linker. Through FESEM, swelling morphology was evaluated in both distilled water and methylene blue dye. The adsorption data elucidated that the adsorption capacity of the hydrogel significantly depends on the dosage of the adsorbent, pH, and concentration of the MB dye. At a pH of 7 and a dye concentration of 250 mg/L, the hydrogel exhibited an impressive 95 % removal rate for methylene blue. The results indicate that the adsorption process follows pseudo-second-order kinetics and conforms well to the Langmuir adsorption isotherm, indicating a maximum adsorption capacity of 1700 mg/g. According to the pseudo-second-order kinetic model and FTIR analysis, methylene blue chemisorbs to the adsorbent material. Hydrogel absorbents regulate adsorption through both intra-particle diffusion and liquid film diffusion. These results highlight the potential of the new hydrogel absorber for water purification.

Eco-friendly engineering of micro composite-based hydroxyapatite bio crystal and polyaniline for high removal of OG dye from wastewater: Adsorption mechanism and RSM@BBD optimization

The presence of harmful substances such as dyes in water systems poses a direct threat to the quality of people's lives and other organisms living in the ecosystem. Orange G (OG) is considered a hazardous dye. The existing paper attempts to evaluate a low-cost adsorbent for the effective removal of OG dye. The developed adsorbent Polyaniline@Hydroxyapatite extracted from Cilus Gilberti fish Scale (PANI@FHAP) was elaborated through the application of the in situ chemical polymerization method to incorporate PANI on the surface of naturally extracted hydroxyapatite FHAP. The good synthesis of PANI@FHAP was evaluated through multiple techniques including X-ray diffraction (XRD), Scanning electron microscopy coupled with energy dispersive X-ray spectrometry (SEM/EDS), Fourier Transforms Infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) coupled with thermal differential analysis (DTA) analysis. The results reveal a highly ordered disposition of PANI chains on FHAP, resulting in a well-coated FHAP in the PANI matrix. Furthermore, the presence of functional groups on the surface of PANI such as amine (-NH2) and imine (=NH) groups would facilitate the removal of OG dye from contaminated water. The adsorption of OG onto PANI@FHAP was conducted in batch mode and optimized through response surface methodology coupled with box-Behnken design (RSM/BBD) to investigate the effect of time, adsorbent dose, and initial concentration. The outcomes proved that OG adsorption follows a quadratic model (R2 = 0.989). The kinetic study revealed that the adsorption of OG fits the pseudo-second-order model. On the other hand, the isotherm study declared that the Freundlich model is best suited to the description of OG adsorption. For thermodynamic study, the adsorption of OG is spontaneous in nature and exothermic. Furthermore, the regeneration-reusability study indicates that PANI@FHAP could be regenerated and reused up to five successive cycles. Based on the FTIR spectrum of PANI@FHAP after OG adsorption, the mechanism governing OG adsorption is predominantly driven by π-π interaction, electrostatic interaction, and hydrogen bonding interactions. The obtained results suppose that PANI@FHAP adsorbent can be a competitive material in large-scale applications.

Purification of aqueous orange II solution through adsorption and visible-light-induced photodegradation using ZnO-modified g-C3N4 composites

Semiconductor-based remediation enables environmentally friendly methods of removing aqueous pollutants. Simply fabricated ZnO modified g-C3N4 composites were utilized as bifunctional adsorptive photocatalysts for orange II removal from aqueous solution through adsorption and photocatalysis processes. The adsorption isotherm data of the g-C3N4 (g-CN) and ZnO modified g-C3N4 (ZCN) composites on orange II solution were better fitted with the Langmuir isotherm compared to the Freundlich isotherm. The maximum adsorption capacity for ZCN-2.5 was slightly higher than that of bare g-CN. According to the adsorption thermodynamics investigation of ZCN-2.5 in orange II solution, the positive values of Gibb's free energy change (ΔG0) suggested a non-spontaneous adsorption process. Furthermore, the negative values of entropy change (ΔS) and enthalpy change (ΔH) indicated the decrement of randomness and exothermic nature during the adsorption process, respectively. The photocatalytic degradation kinetics of g-CN and ZCN composites indicated that the degradation process follows the pseudo-first-order reaction kinetic. The degradation rate of orange II with the ZCN-2.5 composite was 6.67 times higher than that obtained with bare g-CN. Possible adsorption and photocatalytic mechanisms have been proposed.

Constructing the synergistic effects of chitosan and ionic liquid on SPEEK polymer for efficient adsorption of crystal violet dye

In the study, a novel chitosan biopolymer and 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid (IL)-incorporated sulfonated poly (ether ether ketone) (SPEEK) composite (Ch-IL@SPEEK) was prepared for adsorption of cationic crystal violet (CV) dye. The proposed composite was well characterized by several techniques. CV adsorption performance was examined via batch studies by varying various variables involving adsorbent dosage, contact time pH and temperature. The isotherm results were demonstrated the adsorption characters of the processes were Langmuirian. The maximum adsorption capacity was determined as 77.66 mg g-1 for the composite which was significantly higher than SPEEK (qmax = 45.36 mg g-1). The determined equilibrium time of the operated system was 360 min and the kinetic model was assessed as Elovich. At low pHs the protonated surface groups repelled the positively charged CV and the adsorption rate increased with increasing pH. The process is spontaneous and favorable as it proceeds via endothermic interactions. Furthermore, even at the end of 5 successful adsorption cycles, 77.86 % CV removal was obtained. Remarkable efficiencies were also achieved in the removal performance of different organic pollutants. Based on the reported results, Ch-IL@SPEEK composite were exhibited as an impressive adsorbent material for adsorption processes.

Facile Fabrication of Porous Adsorbent with Multiple Amine Groups for Efficient and Selective Removal of Amaranth and Tartrazine Dyes from Water

The development of an advanced dye adsorbent that possesses a range of beneficial characteristics, such as high adsorption capacity, swift adsorption kinetics, selective adsorption capability, and robust reusability, remains a challenge. This study introduces a facile method for fabricating an amine-rich porous adsorbent (ARPA), which is specifically engineered for the adsorptive removal of anionic dyes from aqueous solutions. Through a comprehensive assessment, we have evaluated the adsorption performance of ARPA using two benchmark dyes: amaranth (ART) and tartrazine (TTZ). Our findings indicate that the adsorption process reaches equilibrium in a remarkably short timeframe of just 20 min, and it exhibits an excellent correlation with both the Langmuir isotherm model and the pseudo-second-order kinetic model. Furthermore, ARPA has demonstrated an exceptional maximum adsorption capacity, with values of 675.68 mg g-1 for ART and 534.76 mg g-1 for TTZ. In addition to its high adsorption capacity, ARPA has also shown remarkable selectivity, as evidenced by its ability to selectively adsorb TTZ from a mixed dye solution, a feature that is highly desirable for practical applications. Beyond its impressive adsorption capabilities, ARPA can be efficiently regenerated and recycled. It maintains a high level of original removal efficiency for both ART (76.8%) and TTZ (78.9%) even after five consecutive cycles of adsorption and desorption. Considering the simplicity of its synthesis and its outstanding adsorption performance, ARPA emerges as a highly promising material for use in dye removal applications. Consequently, this paper presents a straightforward and feasible method for the production of an effective dye adsorbent for environmental remediation.

Unraveling the Impact of Adsorbed Molecules on Photocatalytic Processes: Advancements in Understanding Facet-Controlled Semiconductor Photocatalysts

This work aims to demonstrate that the Fe2O3 nanocrystals' adsorptive and photocatalytic properties can be adjusted by exposing the crystal facets that are functionalized. To this end, cube- and disc-like structures were synthesized using a metal ion-mediated hydrothermal route. Thereafter, some of the samples were annealed at 500 °C for 3 h. Our paper combines the experimental part with theoretical calculations of the obtained materials' band edge positions. The results reveal that-aside from hematite-the as-synthesized discs also contain γ-FeOOH and β-Fe2O3 phases, which transform into α-Fe2O3 during annealing. The hydrodynamic diameter, zeta potential, and adsorption kinetics measurements show that the cube-like samples exhibit the highest affinity for cationic, whereas the discs have an affinity for anionic dye. Measurements of the wall zeta potential also reveal that annealing the discs modifies their surface state and ability to adsorb molecules. Photocatalytic tests show that the as-synthesized powders have better photocatalytic performance toward methylene blue decomposition than the annealed ones. The observed small changes in the concentration of the MO during illumination result from the energy band structure of the cube-like crystal orientation.

Reuse of iron ore tailings as an efficient adsorbent to remove dyes from aqueous solution

In this work, an iron ore tailings sample (IOT), collected from a tailings dam in Minas Gerais, Brazil, was characterized. The IOT presented point of zero charge of ∼ 6, specific surface area of 4 m2 g-1, and was mainly composed of hematite and quartz. Subsequently, experiments were performed to evaluate the adsorption of an anionic dye, Direct Red 80 (DR80), and a cationic dye, Methylene Blue (MB), by the IOT, studying the effects of its dose (doseIOT) and the solution initial pH (pH0). The DR80 removal increased with the decrease of the pH0 while the opposite effect occurred in the experiments with the MB, suggesting the process is governed by the adsorption resulting from electrostatic forces. The increase in the doseIOT increased the DR80 and MB removal, which can be attributed to the greater availability of adsorption sites. Pseudo-second order kinetic (R2 > 0.9994) and the Langmuir equilibrium isotherm (R2 > 0.9842) models described well the DR80 adsorption by the IOT, being the reaction rate and maximum adsorption capacity higher at lower pH0. In a regeneration experiment, it was possible to desorb almost entirely the DR80 using a NaOH solution. Additionally, the regenerated IOT was able to adsorb the DR80, demonstrating its reusability. In a preliminary assay, the IOT decreased the colour of the textile wastewater sample at pH0 3. Therefore, the results indicate the potential use of IOT for removing electric-charged pollutants by adsorption, especially anionic ones under acidic conditions.

Exploring the structural characteristics and dye removal capabilities of powder-, granule- and film- shaped magnetic activated carbon derived from Oleaster seed

Dye pollution in water caused by excessive discharge of industrial effluent has become a major environmental problem in recent decades because of its irreversible effects on human health. In this study, low-cost carbon-based adsorbents synthesized from Oleaster seed (OS) were prepared in three forms of powder (PAC), film (FAC), and granule (GAC) and used for the removal of methylene blue dye. The properties of the synthesized adsorbents were characterized by SEM-EDX, BET, XPS and FTIR analyses. The maximum adsorption capacity (qmax) of PAC, FAC, and GAC adsorbents were obtained as 68.49, 32.25, and 15.10 mg/g, respectively at the optimum experimental conditions of pH = 10, adsorbent dosages of 0.5, 1, and 2 g/l, contact times of 60, 90, and 120 min, dye concentration of 10 mg/L, and temperature of 25°C. The Langmuir isotherm well described the equilibrium data for all three adsorbents. The pseudo-second-order kinetic model provided the best fit with the adsorption data obtained from all three adsorbents. Adsorption occurred spontaneously through a combination of chemical and physical mechanisms, with a thermodynamically exothermic process. The desorption experiments demonstrated that all the adsorbents have substantial potential for recovery. The novel activated carbon/alginate composite films are proposed as more promising biosorbents to remove MB dye from the aquatic environment compared to GAC adsorbents.

A critical review and bibliometric analysis of methylene blue adsorption using leaves

The rapid development of the industrial world causes wastewater containing dyes to continue to increase. Even in recent years, the food, textile, cosmetic, plastic, and printing industries have developed the use of dyes. Methylene blue (MB) is one of the cationic dyes widely used in dyeing silk, wood, and cotton because of its absorbency and good fastness to materials. The adsorption process is the best technique and preferred in removing dyes from wastewater due to excellent selectivity, high efficiency from high-quality treated effluent, flexibility in design, and simplicity. Therefore, there is a growing interest to identify low-cost alternative adsorbents that have reasonable adsorption efficiency, especially natural materials such as leaves. In this study, research on MB adsorption using leaves was analyzed using bibliometric analysis. Information of bibliometric is extracted from the Scopus database with the keyword "Methylene Blue", "Adsorption or Desorption", and "Leaves or leaf". The results showed that India, Desalination and Water Treatment, and SASTRA Deemed University were the country, journal, and institution that contributed the most publications on this topic. Therefore, it is expected that with the use of bibliometrics, the use of leaf-based MB adsorption processes in their potential for MB dye removal can be investigated especially for large-scale development.

Postharvest handling of ethylene with oxidative and absorptive means

Fruit ripening is an unfolding of a series of genetically-programmed modifications and tend to be highly orchestrated irrevocable phenomenon mediated by ethylene. Phytohormone ethylene also leads to over-ripening, senescence, loss of texture, microbial attack, reduced post-harvest life and other associated problems during storage and transportation of fruits. Its harmful impacts on fresh fruits, vegetables, and ornamentals result in substantial product losses even up to 80%. Curbing of this inevitable menace is therefore need of the hour. Accrual of ethylene in packaging system should fundamentally be ducked to extend the shelf-life and uphold an adequate superiority of perishables in visual and organoleptic terms. The current review discusses about properties, factors affecting and impact of ethylene, intimidation of its impact at gene vis-à-vis activity level using gene-modification/inhibition techniques, chemical/physical in conjunction with other suitable approaches. It also entails the most commercially cultivated approaches worldwide viz. KMnO4-based oxidation together with adsorption-based scrubbing of ethylene in thorough details. Future ethylene removal strategies should focus on systematic evaluation of KMnO4-based scavenging, exploring the mechanism of adsorption, adsorbent(s) behavior in the presence of other gases and their partial pressures, volatiles, temperature, relative humidity, development of hydrophobic adsorbents to turn-up under high RH, regeneration of adsorbent by desorption, improvement in photocatalytic oxidation etc. and further improvements thereof.

Graphical abstract

Supplementary Information

The online version contains supplementary material available at 10.1007/s13197-023-05777-1.

Optimization and modelling of magnesium oxide (MgO) photocatalytic degradation of binary dyes using response surface methodology

Textile industry dye effluent contains a mixture of different kinds of dyes. Many times, photocatalysis is targeted as a solution for the treatment of dye effluent from the textile industry. Many researches have been published related to the photocatalysis of single textile dyes but in the real-world scenario, effluent is a mixture of dyes. Magnesium oxide (MgO) is used as a photocatalyst to treat a mixture (binary solution) of Methylene blue (MB) and Methylene violet (MV) along with individual MB and MV dyes in this article. MgO shows remarkable photocatalytic activity at about 93 and 88% for MB and MV dye in binary solution within 135 min. Furthermore, to study the influence of process parameters, experiments are designed with the help of the central composite design (CCD), and Response surface methodology (RSM) is used to study the interactions between parameters. For this study, five parameters are selected i.e., Photocatalyst dosage, initial concentration of both dyes, time of exposure to the light source, and pH of the binary solution. The photocatalytic process is also optimized and finally optimization of process parameters is validated with an experiment. The result of the validation experiment is very close to the predicted photocatalytic activity.

Cellulose Nanofiber Films with Gold Nanoparticles Electrostatically Adsorbed for Facile Surface-Enhanced Raman Scattering Detection

Cellulose nanofiber (CNF) holds great promise in applications such as surface-enhanced Raman scattering (SERS), catalysis, esthesia, and detection. This study aimed to build novel CNF-based SERS substrates through a facile synthetic method. Citrate-reduced gold nanoparticles (AuNPs) were adsorbed on the cationized CNF surface due to electrostatic interactions, and uniform AuNPs@(2,3-epoxypropyl trimethylammonium chloride)EPTMAC@CNF flexible SERS substrates were prepared by a simple vacuum-assisted filtration method. The probe molecule methylene blue was chosen to assess the performance of the CNF-based SERS substrate with a sensitivity up to 10-9 M, superior signal reproducibility (relative standard deviation (RSD) = 4.67%), and storage stability (more than 30 days). Tensile strength tests indicated that the CNF-based films had good mechanical properties. In addition, CNF-based substrates can easily capture and visually identify microplastics in water. These results demonstrate the potential application of the flexible, self-assembled AuNPs@EPTMAC@CNF flexible SERS substrate for prompt and sensitive detection of trace substances.

One-Step Synthesis of Polyethyleneimine-Grafted Styrene-Maleic Anhydride Copolymer Adsorbents for Effective Adsorption of Anionic Dyes

Wastewater containing organic dyes has become one of the important challenges in water treatment due to its high salt content and resistance to natural degradation. In this work, a novelty adsorbent, PEI-SMA, was prepared by grafting polyethyleneimine (PEI) onto styrene-maleic anhydride copolymer (SMA) through an amidation reaction. The various factors, such as pH, adsorbent dosage, contact time, dye concentration, and temperature, which may affect the adsorption of PEI-SMA for Reactive Black 5 (RB5), were systematically investigated by static adsorption experiments. The adsorption process of PEI-SMA for RB5 was more consistent with the Langmuir isotherm model and the pseudo-second-order model, suggesting a single-layer chemisorption. PEI-SMA exhibits excellent adsorption performance for RB5 dye, with a maximum adsorption capacity of 1749.19 mg g-1 at pH = 2. Additionally, PEI-SMA exhibited highly efficient RB5 competitive adsorption against coexisting Cl- and SO42- ions and cationic dyes. The adsorption mechanism was explored, and it can be explained as the synergistic effect of electrostatic interaction, hydrogen bonding and π-π interaction. This study demonstrates that PEI-SMA could act as a high performance and promising candidate for the effective adsorption of anionic dyes from aqueous solutions.

Effective adsorption of fluorescent congo red azo dye from aqueous solution by green synthesized nanosphere ZnO/CuO composite using propolis as bee byproduct extract

The indirect dumping of massive volumes of toxic dyes into water has seriously affected the ecosystem. Owing to the many applications of the designed nanomaterials in the manufacturing process, there is a lot of research interest in synthesizing nanomaterials using green processes. In this research, the byproduct of bee was employed to synthesize nanoparticles (NPs) of ZnO, CuO, and biosynthesized ZnO/CuO (BZC) nanocomposite via utilizing a green and simple approach. To validate the effective fabrication of BZC nanocomposite, various characterization measurements were applied. FTIR analysis identified the functional groups in charge of producing nanoparticles and nanocomposites. Moreover, the existence of ZnO and CuO XRD peaks suggests that the nanocomposites were successfully biosynthesized. The high-resolution XPS spectrum of the BZC nanocomposite's Zn2p3, Cu2p3, and O1s were observed. Our findings indicate the successful engineering of the prepared nanomaterials and BZC nanocomposite. Our findings indicate the successful engineering of the prepared nanomaterials and BZC nanocomposite. For Congo red (CR) fluorescent stain azo dye elimination in water, all adsorption parameters were examined at room temperature. Moreover, the adsorption experiments revealed the removal capacity for uptake CR dye using BZC nanocomposite (90.14 mg g-1). Our results show that the BZC nanocomposite exhibited high removal capability for the adsorption of CR dye. The nanosphere adsorbent offered a simple, low-cost, and green approach for water purification and industrial wastewater control.

Exploring the Ecological Implications, Gastronomic Applications, and Nutritional and Therapeutic Potential of Juglans regia L. (Green Walnut): A Comprehensive Review

The green walnut, which is frequently overlooked in favor of its more mature sibling, is becoming a topic of great significance because of its unique ecological role, culinary flexibility, and therapeutic richness. The investigation of the bioactive substances found in green walnuts and their possible effects on human health has therapeutic potential. Juglans regia L. is an important ecological component that affects soil health, biodiversity, and the overall ecological dynamic in habitats. Comprehending and recording these consequences are essential for environmental management and sustainable land-use strategies. Regarding cuisine, while black walnuts are frequently the main attraction, green walnuts have distinct tastes and textures that are used in a variety of dishes. Culinary innovation and the preservation of cultural food heritage depend on the understanding and exploration of these gastronomic characteristics. Omega-3 fatty acids, antioxidants, vitamins, and minerals are abundant in green walnuts, which have a comprehensive nutritional profile. Walnuts possess a wide range of pharmacological properties, including antioxidant, antibacterial, antiviral, anticancer, anti-inflammatory, and cognitive-function-enhancing properties. Consuming green walnuts as part of one's diet helps with antioxidant defense, cardiovascular health, and general well-being. Juglans regia L., with its distinctive flavor and texture combination, is not only a delicious food but also supports sustainable nutrition practices. This review explores the nutritional and pharmacological properties of green walnuts, which can be further used for studies in various food and pharmaceutical applications.

Efficient dye adsorption of mesoporous activated carbon from bamboo parenchyma cells by phosphoric acid activation

In order to solve the environmental damage caused by the discharge of dyes as industrial wastewater, the development of efficient and sustainable adsorbents is the key, while most of the previous studies on bamboo parenchyma cells have focused on their microstructural, functional and mechanical properties, and few of the properties in adsorption have been investigated. To evaluate the role of the unique microstructure of bamboo parenchyma cells on adsorption after carbonization and activation, PC-based activated carbon (PPAC) was fabricated by the phosphoric acid activation method and tested for adsorption using methylene blue (MB). The effect of mesoporous structure on MB adsorption was investigated in detail using PPAC-30C impregnated with phosphoric acid at a concentration of 30%. The results showed that the adsorption performance was influenced by single-factor experiments (e.g., pH, activated carbon dosing). The adsorption isotherms and kinetics could conform to the Langmuir model (R2 = 0.983-0.994) and pseudo-second-order kinetic model (R2 = 0.822-0.991) respectively, and the maximum MB adsorption capacity of adsorbent was 576 mg g-1. The adsorption mechanism of MB on PPAC-30C includes physical adsorption, electrostatic attraction, hydrogen bonding, and the π-π conjugation effect, which was dominated by physical adsorption. The results of this study show that PPAC has good application prospects for cationic dye removal.

Enhanced dye sequestration with natural polysaccharides-based hydrogels: A review

Due to the expansion of industrial activities, the concentration of dyes in water has been increasing. The dire need to remove these pollutants from water has been heavily discussed. This study focuses on the reproducible and sustainable solution for wastewater treatment and dye annihilation challenges. Adsorption has been rated the most practical way of the several decolorization procedures due to its minimal initial investment, convenient utility, and high-performance caliber. Hydrogels, which are three-dimensional polymer networks, are notable because of their potential to regenerate, biodegrade, absorb bulky amounts of water, respond to stimuli, and have unique morphologies. Natural polysaccharide hydrogels are chosen over synthetic ones because they are robust, bioresorbable, non-toxic, and cheaply accessible. This study has covered six biopolymers, including chitosan, cellulose, pectin, sodium alginate, guar gum, and starch, consisting of their chemical architecture, origins, characteristics, and uses. The next part describes these polysaccharide-based hydrogels, including their manufacturing techniques, chemical alterations, and adsorption effectiveness. It is deeply evaluated how size and shape affect the adsorption rate, which has not been addressed in any prior research. To assist the readers in identifying areas for further research in this subject, limitations of these hydrogels and future views are provided in the conclusion.

Accessible Eco-Friendly Method for Wastewater Removal of the Azo Dye Reactive Black 5 by Reusable Protonated Chitosan-Deep Eutectic Solvent Beads

A novel approach to enhance the utilization of low-cost and sustainable chitosan for wastewater remediation is presented in this investigation. The study centers around the modification of chitosan beads using a deep eutectic solvent composed of choline chloride and urea at a molar ratio of 1:2, followed by treatment with sulfuric acid using an impregnation accessible methodology. The effectiveness of the modified chitosan beads as an adsorbent was evaluated by studying the removal of the azo dye Reactive Black 5 (RB5) from aqueous solutions. Remarkably, the modified chitosan beads demonstrated a substantial increase in adsorption efficiency, achieving excellent removal of RB5 within the concentration range of 25-250 mg/L, ultimately leading to complete elimination. Several key parameters influencing the adsorption process were investigated, including initial RB5 concentration, adsorbent dosage, contact time, temperature, and pH. Quantitative analysis revealed that the pseudo-second-order kinetic model provided the best fit for the experimental data at lower dye concentrations, while the intraparticle diffusion model showed superior performance at higher RB5 concentration ranges (150-250 mg/L). The experimental data were successfully explained by the Langmuir isotherm model, and the maximum adsorption capacities were found to be 116.78 mg/g at 298 K and 379.90 mg/g at 318 K. Desorption studies demonstrated that approximately 41.7% of the dye could be successfully desorbed in a single cycle. Moreover, the regenerated adsorbent exhibited highly efficient RB5 removal (80.0-87.6%) for at least five consecutive uses. The outstanding adsorption properties of the modified chitosan beads can be attributed to the increased porosity, surface area, and swelling behavior resulting from the acidic treatment in combination with the DES modification. These findings establish the modified chitosan beads as a stable, versatile, and reusable eco-friendly adsorbent with high potential for industrial implementation.

Natural Polysaccharide-Based Hydrogels Used for Dye Removal

Removal of contaminants from discharge water is vital and demands urgent assistance with the goal to keep clean water. Adsorption is one of the most common, efficient, and low-priced methods used in water treatment. Various polysaccharide-based gels have been used as efficient dye adsorbents from wastewater. This review summarizes cutting-edge research of the last decade of different hydrogels based on natural polysaccharides (chitin, chitosan, cellulose, starch, pullulan, and dextran) concerning their dye adsorption efficiency. Beyond their natural abundance, attributes of polysaccharides such as biocompatibility, biodegradability, and low cost make them not only efficient, but also environmentally sustainable candidates for water purification. The synthesis and dye removal performance together with the effect of diverse factors on gels retaining ability, kinetic, and isotherm models encountered in adsorption studies, are introduced. Thermodynamic parameters, sorbent recycling capacity along with conclusions and future prospects are also presented.

Smartphone-based procedure to determine content of single synthetic dyes in food using the Arata-Possetto extraction method

The use of additives, including dyes, is common in the preparation of food products. The analytical control of artificial food dye content is relevant since some, such as azo dyes, may produce cancer and attention deficit disorders and hyperactivity in children. Consequently, the maximum permitted concentration of azo dyes in food is regulated by current legislation. Therefore, it is of interest to find simple and fast procedures for the control of these compounds. The aim of this study is to determine the concentration of azo dyes in food samples by the Arata-Possetto method - based on the extraction of azo dyes employing natural wool -, followed by the analysis of an image captured by a smartphone camera. After experimentally determining the optimal extraction conditions, the calibration curves for standard solutions of different food dyes and the color of the dyed wool were obtained. Results from dyed wool image processing were compared with the absorbance spectra of the solutions before extraction as measured by a diode array spectrophotometer. The spectrophotometric and the image processing procedures were employed to obtain the calibration curves for different food dyes, which were subsequently employed to analyze food samples. Statistical treatment shows that the results of both methods are comparable.

Comparative study of synthesis methods and pH-dependent adsorption of methylene blue dye on UiO-66 and NH2-UiO-66

Metal-organic frameworks (MOFs) are highly promising adsorbents with notable properties such as elevated adsorption capacities and versatile surface design capabilities. This study introduces two distinct synthesis methods, one lasting 1 h and the other 24 h, for UiO-66 and NH2-UiO-66. While both methods yield structures with comparable crystallinity and morphology, the adsorption performance of the cationic methylene blue dye varies at different pH levels. Despite the 24 h synthesis time being optimal for maximum adsorption in both MOFs, the relative difference in NH2-UiO-66 adsorption percentage at different times suggests reduced dependency on synthesis time for this property. Notably, NH2-UiO-66 exhibits consistent and effective performance across three pH levels, warranting further investigation into its adsorption kinetics and isotherm. The achievement of high adsorption efficiency coupled with a significantly reduced synthesis time underscores the importance of developing simplified synthetic methods, essential for enhancing the practical applicability of MOFs in diverse applications.

Investigation of adsorption potential of acid violet 90 dye with chitosan/halloysite/boron nitride composite materials

In this study, composite adsorbents consisting of a mixture of chitosan (CTS), boron nitride (h-BN) and halloysite (HNT) were used for the adsorption of Acid Violet 90 (AV90) dye in a batch system. Adsorbents CTS, CTS/HNT, CTS/h-BN and CTS/h-BN/HNT beads were prepared by simple dropping method and dried in a freeze dryer. The beads were characterized by FT-IR, SEM and zeta potential analysis. The effects of pH (2-8) and dye concentration (50-250 mg/L) on AV90 adsorption properties of beads were investigated. In addition, Langmuir, Freunlich, Temkin and Henry adsorption isotherm models were used to examine the dye adsorption mechanism. It was observed that the Langmuir and Freundlich adsorption isotherm models were in good agreement with the experimental data. In the dye concentration range studied, the qm values of CTS, CTS/h-BN1, CTS/h-BN3, CTS/HNT/h-BN1, CTS/HNT/h-BN3, CTS/HNT obtained from the Langmuir isotherm model was 27.62, 17.80, 10.11, 8.71, 32.57, 19.96 mg/g, respectively. Pseudo-first order, pseudo-second order and intra-particle diffusion kinetic models were used to examine the adsorption kinetics of adsorbents. As a result, it is thought that the use of this study in the field of dye adsorption can be an innovative and important study.

Review on emerging trends and challenges in the modification of xanthan gum for various applications

This review explores the realm of structural modifications and broad spectrum of their potential applications, with a special focus on the synthesis of xanthan gum derivatives through graft copolymerization methods. It delves into the creation of these derivatives by attaching functional groups (-OH and -COOH) to xanthan gum, utilizing a variety of initiators for grafting, and examining their diverse applications, especially in the areas of food packaging, pharmaceuticals, wastewater treatment, and antimicrobial activities. Xanthan gum is a biocompatible, biodegradable, less toxic, bioactive, and cost-effective natural polymer derived from Xanthomonas species. The native properties of xanthan gum can be improved by cross-linking, grafting, curing, blending, and various modification techniques. Grafted xanthan gum has excellent biodegradability, metal binding, dye adsorption, immunological properties, and wound healing ability. Owing to its remarkable properties, such as biocompatibility and its ability to form gels resembling the extracellular matrix of tissues, modified xanthan gum finds extensive utility across biomedicine, engineering, and the food industry. Furthermore, the review also covers various modified derivatives of xanthan gum that exhibit excellent biodegradability, metal binding, dye adsorption, immunological properties, and wound healing abilities. These applications could serve as important resources for a wide range of industries in future product development.

Optimization by Box-Behnken design for environmental contaminants removal using magnetic nanocomposite

In this study, a CoO-Fe2O3/SiO2/TiO2 (CIST) nanocomposite was synthesized and utilized as an adsorbent to remove methylene blue (MB), malachite green (MG), and copper (Cu) from aqueous environments. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and X-ray diffraction (XRD). Input parameters included pH (3-10), contact time (10-30 min), adsorbent amount (0.01-0.03 g), and pollutant concentration (20-60 mg L-1). The effects of these parameters on the removal process efficiency were modeled and optimized using the response surface methodology (RSM) based on the Box-Behnken design (BBD). The RSM-BBD method demonstrated the capability to develop a second-degree polynomial model with high validity (R2 ˃ 0.99) for the removal process. The optimization results using the RSM-BBD method revealed a removal efficiency of 98.01%, 93.06%, and 88.26% for MB, MG, and Cu, respectively, under optimal conditions. These conditions were a pH of 6, contact time of 10 min, adsorbent amount of 0.025 g, and concentration of 20 mg L-1. The synthesized adsorbent was recovered through five consecutive adsorption-desorption cycles using hydrochloric acid. The results showed an approximately 12% reduction from the first to the seventh cycle. Also, MB, MG, and Cu removal from real water samples in optimal conditions was achieved in the range of 81.69-98.18%. This study demonstrates the potential use of CIST nanocomposite as an accessible and reusable option for removing MB, MG, and Cu pollutants from aquatic environments.

Enhanced photocatalytic performance of the N-rGO/g-C3N4 nanocomposite for efficient solar-driven water remediation

This paper describes the synthesis and analysis of a photocatalyst made from a combination of reduced graphene oxide (rGO) and graphitic carbon nitride (g-C3N4) through a simple hydrothermal process. The effectiveness of the N-rGO/g-C3N4 heterostructure in photocatalysis was examined by studying the breakdown of different types of organic pollutants, such as cationic and anionic dyes, as well as antibiotics, under simulated solar light irradiation. Due to the presence of Schottky junctions formed between rGO and g-C3N4, the electron transfer process is significantly enhanced, leading to a reduction in the recombination of photogenerated electrons and holes. As a result, the photocatalytic activity of the rGO/g-C3N4 photocatalyst is significantly higher compared to that of g-C3N4 alone. The photocatalytic performance was further augmented through the nitrogen doping of rGO, which led to an increase in conductivity due to electron doping and an enhancement in the charge separation process. The heterojunction of rGO/g-C3N4 with an optimum concentration of 60% rGO attained a degradation efficiency of 98.7% for rhodamine B (RhB) dye after 50 minutes of light irradiation. In comparison, the nitrogen-doped photocatalyst (N-rGO/g-C3N4) achieved a photodegradation efficiency of 99.99% within 30 minutes. The reaction rate constant of the N-rGO/g-C3N4 nanocomposite was found to be 0.11 min-1 using pseudo first-order rate kinetics. This value is about 16 times more than that of pure g-C3N4 (0.007 min-1) for the degradation of rhodamine B. Additionally, N-rGO/g-C3N4 effectively degraded various contaminants, such as methylene blue, methyl orange, and tetracycline hydrochloride. The paper also addresses the photocatalytic mechanism, which entails the facilitated movement of electrons and holes produced by light, owing to the alignment of energy bands at the interface of the N-rGO/g-C3N4 heterojunction. These findings contribute to the advancement of a metal-free and porous photocatalyst that is highly interconnected and can be used for waste water treatment and environmental remediation.

Bimetallic Organic Gel for Effective Methyl Orange Dye Adsorption

A bimetallic organic gel (MOG-Fe/Al) was synthesized through the solvothermal method. The gel state of the product obtained under optimized gel formation conditions is sufficient to carry 2 g of weight for a long time. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, Brunauer-Emmett-Teller (BET) technique, and X-ray photoelectron spectroscopy (XPS) analysis confirmed the structures and morphologies of the synthesized materials. MOG-Fe/Al, with good stability, excellent durability, and wide applicability, exhibited efficient MO adsorption capacity as high as 335.88 mg/g at 25 °C. Adsorption-influencing factors including solution pH, contact time, and temperature were investigated. The adsorption performance of the bimetallic organic gel was better than that of the monometallic organic gels (MOG-Fe and MOG-Al), and its adsorption processes were in accordance with the pseudo-second-order kinetic and Langmuir isothermal models. The excellent adsorption capacity of the MOG-Fe/Al is due to its surface structure, pore volume, π-π interactions, hydrogen bonds, and electrostatic interactions.

Fermentation of millet bran with Bacillus natto: enhancement of bioactivity levels and the bioactivity of bran extract

BACKGROUND

Millet bran (MB), a byproduct of millet production, is rich in functional components but it is underutilized. In recent years, researchers have shown that fermentation can improve the biological activity of cereals and their byproducts. This study used Bacillus natto to ferment millet bran to improve its added value and broaden the application of MB. The bioactive component content, physicochemical properties, and functional activity of millet bran extract (MBE) from fermented millet bran were determined.

RESULTS

After fermentation, the soluble dietary fiber (SDF) content increased by 92.0%, the β-glucan content by 164.4%, the polypeptide content by 111.4%, the polyphenol content by 32.5%, the flavone content by 16.4%, and the total amino acid content by 95.4%. Scanning electron microscopy revealed that the microscopic morphology of MBE changed from complete and dense blocks to loosely porous shapes after fermentation. After fermentation, the solubility, water-holding capacity, and viscosity significantly increased and the particle size decreased. Moreover, the glucose adsorption capacity (2.1 mmol g-1), glucose dialysis retardation index (75.3%), and α-glucosidase inhibitory (71.4%, mixed reversible inhibition) activity of the fermented MBE (FMBE) were greater than those of the unfermented MBE (0.99 mmol g-1, 32.1%, and 35.1%, respectively). The FMBE presented better cholesterol and sodium cholate (SC) adsorption properties and the adsorption was considered inhomogeneous surface adsorption.

CONCLUSION

Fermentation increased the bioactive component content and improved the physicochemical properties of MBE, thereby improving its hypoglycemic and hypolipidemic properties. This study not only resolves the problem of millet bran waste but also encourages the development of higher value-added application methods for millet bran. © 2024 Society of Chemical Industry.

A review of pre- and post-surface-modified neem (Azadirachta indica) biomass adsorbent: Surface functionalization mechanism and application

In contemporary wastewater treatment industry, advanced oxidation techniques, membrane filtration, ion exchange, and reverse osmosis are used to treat chemically loaded wastewater. All these methods required highly toxic oxidizing chemicals, high capital investment in membrane/filter materials, and the installation of sophisticated equipment. Wastewater treatment through an adsorption process using biomass-based adsorbent is economical, user-friendly, and sustainable. Neem tree waste has been explored as an adsorbent for wastewater treatment. The chemical components in the neem biomass include carbohydrates, fat, fiber, cellulose, hemicellulose, and lignin, which support the functionalization of neem biomass. Moreover, adsorbent preparation from renewable resources is not only cost-effective and environmentally friendly but also helps in waste management for sustainable growth. Contemporary researchers explored the pre- and post-surface-modified neem biomass adsorbents in scavenging the pollutants from contaminated water. This review extensively explores the activation process of neem biomass, physical and chemical methods of surface modification mechanism, and the factors affecting surface modification. The pollutant removal through pre and post-surface-modified neem biomass adsorbents was also summarized. Furthermore, it also provides a comprehensive summary of the factors that affect the adsorption performance of the neem biomass-derived adsorbents against dyes, metal ions, and other emerging pollutants. Understanding the surface-modification mechanisms and the adsorption efficiency factor of adsorbents will help in harnessing their potential for more efficiently combatting environmental pollution and making strides toward a greener and more sustainable future.

Decolorization and degradation of various dyes and dye-containing wastewater treatment by electron beam radiation technology: An overview

The treatment of dye-containing wastewater generated from textile industries is still a challenge, and various technologies, including physical, chemical and biological ones have been used. In recent years, the ionizing radiation (usually including gamma ray generated by radionuclide, such as 60Co and 137Cs, and electron beam generated by electron accelerator) technology has received increasing attention for degrading refractory or toxic organic pollutants in wastewater because of its unique advantages, such as no chemical additives, fast reaction rate, strong degradation capacity, high efficiency, flexibility, controllability. Compared to the conventional wastewater treatment processes, ionizing radiation technology, as a disruptive wastewater treatment technology, is more efficient for the decolorization and degradation of dyes and the treatment of dye-containing wastewater. In this paper, the recent advances in the treatment of dye-containing wastewater by ionizing radiation, in particular by electron beam (EB) radiation were summarized and analyzed, focusing on the decolorization and degradation of various dyes. Firstly, the formation of various reactive species induced by radiation and their interactions with dye molecules, as well as the influencing factors on the removal efficiency of dyes were discussed. Secondly, the researches on the treating dye-containing wastewater by electron beam radiation technology were systematically reviewed. Then, the decolorization and degradation mechanisms by electron beam radiation were further discussed in detail. And the integrated processes that would contribute to the advancement of this technology in practical applications were examined. More importantly, the recent advances of electron beam radiation technology from laboratory to application were reviewed, especially successful operation of dye-containing wastewater treatment facilities in China. And eventually, current challenges, future research directions, and outlooks of electron beam radiation technology were proposed for further advancing this technology for the sustainable development of water resources.

Catalytic innovations: Improving wastewater treatment and hydrogen generation technologies

The effective reduction of hazardous organic pollutants in wastewater is a pressing global concern, necessitating the development of advanced treatment technologies. Pollutants such as nitrophenols and dyes, which pose significant risks to both human and aquatic health, making their reduction particularly crucial. Despite the existence of various methods to eliminate these pollutants, they are not without limitations. The utilization of nanomaterials as catalysts for chemical reduction exhibits a promising alternative owing to their distinguished catalytic activity and substantial surface area. For catalytically reducing the pollutants NaBH4 has been utilized as a useful source for it because it reduces the pollutants quiet efficiently and it also releases hydrogen gas as well which can be used as a source of energy. This paper provides a comprehensive review of recent research on different types of nanomaterials that function as catalysts to reduce organic pollutants and also generating hydrogen from NaBH4 methanolysis while also evaluating the positive and negative aspects of nanocatalyst. Additionally, this paper examines the features effecting the process and the mechanism of catalysis. The comparison of different catalysts is based on size of catalyst, reaction time, rate of reaction, hydrogen generation rate, activation energy, and durability. The information obtained from this paper can be used to steer the development of new catalysts for reducing organic pollutants and generation hydrogen by NaBH4 methanolysis.

Preparation of Aminated Sodium Lignosulfonate and Efficient Adsorption of Methyl Blue Dye

The aminated sodium lignosulfonate (AELS) was prepared through a Mannich reaction and characterized via FT-IR, TG, SEM and XPS in this study. Subsequently, the adsorption capacity of AELS for methyl blue (MB) was evaluated under various conditions such as pH, adsorbent dosage, contact time, initial concentration and temperature. The adsorption kinetics, isotherms and thermodynamics of AELS for methyl blue were investigated and analyzed. The results were found to closely adhere to the pseudo-second-order kinetic model and Langmuir isotherm model, suggesting a single-molecular-layer adsorption process. Notably, the maximum adsorption capacity of AELS for methyl blue (153.42 mg g-1) was achieved under the specified conditions (T = 298 K, MAELS = 0.01 g, pH = 6, VMB = 25 mL, C0 = 300 mg L-1). The adsorption process was determined to be spontaneous and endothermic. Following five adsorption cycles, the adsorption capacity exhibited a minimal reduction from 118.99 mg g-1 to 114.33 mg g-1, indicating good stability. This study contributes to the advancement of utilizing natural resources effectively and sustainably.

Adsorption of hexavalent chromium from wastewater using polyaniline-coated microcrystalline cellulose nanocomposites

In this study, the effectiveness of microcrystalline cellulose (MCC) as an adsorbent for the removal of hexavalent chromium, Cr(vi), from synthetic wastewater was enhanced through functionalization with polyaniline (PANI). Scanning electron microscopy (SEM) showed that MCC was an effective scaffold for in situ chemical oxidative polymerization of aniline. Fourier transform infrared spectroscopy (FTIR) spectroscopy and X-ray diffraction confirmed successful PANI synthesis. The MCC/PANI nanocomposites exhibited relatively high specific surface areas, compared to that of the MCC (2.05 m2 g-1). Batch adsorption studies showed that the optimal conditions for the removal of Cr(vi) from wastewater using the MCC/PANI-69 wt% nanocomposite were an initial Cr(vi) concentration of 100 mg L-1, an adsorbent dosage of 4 g L-1 and a Cr(vi) solution pH of 7. The MCC/PANI-69 wt% required only 30 min to reach equilibrium and the equilibrium removal efficiency was 95%. FTIR spectroscopy and energy dispersive X-ray spectrometry results suggest that the Cr(vi) removal mechanism by the MCC/PANI-69 wt% nanocomposite at pH 7 was through electrostatic attraction of Cr(vi) species by PANI, reduction of Cr(vi) into Cr(iii) and precipitation of Cr(iii) on the nanocomposite surface. The kinetics for the removal of the Cr(vi) by the MCC/PANI-69 wt% nanocomposite were adequately described by the pseudo second order (PSO) kinetics model, whereas the Langmuir isotherm adequately described the equilibrium data. The MCC/PANI-69 wt% nanocomposite had a significantly improved maximum adsorption capacity of 35.97 mg g-1, at pH 7, in comparison to that of the MCC (3.92 mg g-1 at pH 1). The study demonstrated that, whereas most of the reported adsorbents for Cr(vi) are only effective at low pH values, the MCC/PANI nanocomposite synthesized in this study was effective at pH 7.

Adsorptive Elimination of a Cationic Dye and a Hg (II)-Containing Antiseptic from Simulated Wastewater Using a Metal Organic Framework

Several types of pollutants have acute adverse effects on living bodies, and the effective removal of these pollutants remains a challenge. Safranin O (a biological dye) and merbromin (a topical mercury-containing antiseptic) are considered organic pollutants, and there are only a few reports on their removal. Synthesized and well-characterized (through PXRD, FTIR, FESEM, and EDS analysis) MOF-5 was used for the first time in the removal of safranin O and merbromin from simulated wastewater and real wastewater. In both cases, MOF-5 effectively removed contaminants. We found that in simulated wastewater, the highest efficiency of removal of safranin O was 53.27% (for 15 mg/L) at pH 10, and for merbromin, it was 41.49% (for 25 mg/L) at pH 6. In the case of real wastewater containing natural ions (Na+, K+, F-, Cl-, SO42-, PO43-, Mg2+, and Ca2+) and other molecules, the removal efficiencies of these two dyes decreased (34.00% and 26.28% for safranin O and merbromin, respectively) because of the presence of other ions and molecules. A plausible mechanism for the removal of these pollutants using MOF-5 was proposed.

Cellulose-alginate hydrogels and their nanocomposites for water remediation and biomedical applications

In the last decade, both cellulose and alginate polysaccharides have been extensively utilized for the synthesis of biocompatible hydrogels because of their alluring characteristics like low cost, biodegradability, hydrophilicity, biodegradability, ease of availability and non-toxicity. The presence of abundant hydrophilic functional groups (like carboxyl and hydroxyl) on the surface of cellulose and alginate or their derivatives makes these materials promising candidates for the preparation of hydrogels with appealing structures and characteristics, leading to growing research in water treatment and biomedical fields. These two polysaccharides are typically blended together to improve hydrogels' desired qualities (mechanical strength, adsorption properties, cellulose/alginate yield). So, keeping in view their extensive applicability, in the present review article, recent advances in the development of cellulose/nanocellulose-alginate-based hydrogels and their relevance in water treatment (adsorption of dyes, heavy metals, etc.) and biomedical field (wound healing, tissue engineering, drug delivery) has been reviewed. Further, impact of other inorganic/organic additives in cellulose/nanocellulose-alginate-based hydrogels properties like contaminants adsorption, drug delivery, tissue engineering, etc., has also been studied. Moreover, the current difficulties and future prospects of nanocellulose-alginate-based hydrogels regarding their water purification and biomedical applications are also discussed at the end.

AgTNP@TiO2@Ag core-satellite composites for sensitive sensing and in situ monitoring photodegradation of organic dyes by portable Raman spectrometer

The development of sensitive, reliable, and robust substrates for surface-enhanced Raman spectroscopy (SERS) heavily relies on the creation of numerous hot spots. In this study, we propose a simple approach to fabricate core-satellite composites composed of AgTNP@TiO2@Ag, where Ag triangular nanoplates (AgTNPs) act as the cores, TiO2 serves as the interlayer, and Ag nanoparticles are deposited around them to form Ag satellites. By adjusting the amount of AgNO3, we precisely control the coverage of Ag nanoparticles on AgTNP@TiO2@Ag, thus fine-tuning their SERS sensitivity. Various characterization techniques were employed to examine their composition, morphology, and crystal structure. Thanks to the abundant hot spots created by the Ag satellites, these composites exhibit significantly enhanced SERS sensitivity and they demonstrate the capability to detect methylene blue (MB) at a concentration of 10-10 M by portable Raman spectrometer. Moreover, the AgTNP@TiO2@Ag composites effectively enable in situ SERS monitoring of the photodegradation reaction of MB. Overall, the novel AgTNP@TiO2@Ag composites prepared in this study exhibit high SERS sensitivity and excellent photocatalytic performance, making them highly valuable for environmental detection and ecological restoration purposes.

Advancements in textile dye removal: a critical review of layered double hydroxides and clay minerals as efficient adsorbents

The textile industry is responsible for producing large volumes of wastewater that contain a wide variety of dye compounds. This poses a significant environmental hazard and risks harming both ecosystems and living organisms. This review study explores the advancements in adsorption research for dye removal, with a particular emphasis on the development of various adsorbents. The article provides detailed insights into the toxicity and classification of dyes, different treatment techniques, and the characteristics of numerous adsorbents, with special attention to layered double hydroxides (LDH) and clay minerals. A comprehensive list of adsorbents, encompassing natural materials, agricultural by-products, industrial waste, and activated carbon, is discussed for effective removal of different dyes. Furthermore, the review extensively examines the influence of various adsorption variables, such as pH, initial dye concentration, adsorbent dosage, temperature, contact time, ionic strength, and pore volume of the adsorbent. Additionally, the application of response surface methodology for optimizing adsorption variables is elucidated. Commonly, electrostatic attraction, π-π interactions, n-π interactions, van der Waals forces, H-bonding, and pore diffusion play a major role in adsorption mechanism. The review also found that LDH can eliminate a wide range of dyes from wastewater, achieving excellent uptake capacities often exceeding 500 mg/g, with a removal efficiency of 99%. The Langmuir isotherm and pseudo-second-order kinetic equations gave the best fit to most of the adsorption data. Overall, this review serves as a valuable resource for researchers and practitioners seeking sustainable solutions to address the environmental challenges posed by textile dye contamination.

Adsorption of contaminants by nanomaterials synthesized by green and conventional routes: a critical review

Nanomaterials, due to their large surface area and selectivity, have stood out as an alternative for the adsorption of contaminants from water and effluents. Synthesized from green or traditional protocols, the main advantages and disadvantages of green nanomaterials are the elimination of the use of toxic chemicals and difficulty of reproducing the preparation of nanomaterials, respectively, while traditional nanomaterials have the main advantage of being able to prepare nanomaterials with well-defined morphological properties and the disadvantage of using potentially toxic chemicals. Thus, based on the particularities of green and conventional nanomaterials, this review aims to fill a gap in the literature on the comparison of the synthesis, morphology, and application of these nanomaterials in the adsorption of contaminants in water. Focusing on the adsorption of heavy metals, pesticides, pharmaceuticals, dyes, polyaromatic hydrocarbons, and phenol derivatives in water, for the first time, a review article explored and compared how chemical and morphological changes in nanoadsorbents synthesized by green and conventional protocols affect performance in the adsorption of contaminants in water. Despite advances in the area, there is still a lack of review articles on the topic.

A critical review on the separation of heavy metal(loid)s from the contaminated water using various agricultural wastes

Wastewater contamination with heavy metal(loids)s has become a worldwide environmental and public health problem due to their toxic and non-degradable nature. Different methods and technologies have been applied for water/wastewater treatment to mitigate heavy metal(loid)-induced toxicity threat to humans. Among various treatment methods, adsorption is considered the most attractive method because of its high ability and efficiency to remove contaminants from wastewater. Agricultural waste-based adsorbents have gained great attention because of high efficiency to heavy metal(loids)s removal from contaminated water. Chemically modified biosorbents can significantly enhance the stability and adsorption ability of the sorbents. The two mathematical models of sorption, Freundlich and Langmuir isotherm models, have mostly been studied. In kinetic modeling, pseudo-second-order model proved better in most of the studies compared to pseudo-first-order model. The ion exchange and electrostatic attraction are the main mechanisms for adsorption of heavy metal(loid)s on biosorbents. The regeneration has allowed various biosorbents to be recycled and reused up to 4-5 time. Most effective eluents used for regeneration are dilute acids. For practical perspective, biosorbent removal efficiency has been elucidated using various types of wastewater and economic analysis studies. Economic analysis of adsorption process using agricultural waste-based biosorbents proved this approach cheaper compared to traditional commercial adsorbents, such as chemically activated carbon. The review also highlights key research gaps to advance the scope and application of waste peels for the remediation of heavy metal(loid)s-contaminated wastewater.

Green, Low-carbon Silk-based Materials in Water Treatment: Current State and Future Trends

The improper and inadequate treatment of industrial, agricultural, and household wastewater exerts substantial pressure on the existing ecosystem and poses a serious threat to the health of both humans and animals. To address these issues, different types of materials have been employed to eradicate detrimental pollutants from wastewater and facilitate the reuse of water resources. Nevertheless, owing to the challenges associated with the degradation of these traditional materials post-use and their incompatibility with the environment, natural biopolymers have garnered considerable interest. Silk protein, as a biomacromolecule, exhibits advantageous characteristics including environmental friendliness, low carbon emissions, biodegradability, sustainability, and biocompatibility. Considering recent research findings, this comprehensive review outlines the structure and properties of silk proteins and offers a detailed overview of the manufacturing techniques employed in the production of silk-based materials (SBMs) spanning different forms. Furthermore, it conducts an in-depth analysis of the state-of-the-art SBMs for water treatment purposes, encompassing adsorption, catalysis, water disinfection, desalination, and biosensing. The review highlights the potential of SBMs in addressing the challenges of wastewater treatment and provides valuable insights into prospective avenues for further research.

Machine learning approaches for the treatment of textile wastewater using sugarcane bagasse (Saccharum officinarum) biochar

Most dyes present in wastewater from the textile industry exhibit toxicity and are resistant to biodegradation. Hence, the imperative arises for the environmentally significant elimination of textile dye by utilising agricultural waste. The achievement of this objective can be facilitated through the utilisation of the adsorption mechanism, which entails the passive absorption of pollutants using biochar. In this study, we compare the efficacy of the response surface methodology (RSM), the artificial neural network (ANN), the k-nearest neighbour (kNN), and adaptive neuro-fuzzy inference system (ANFIS) in removing crystal violet (CV) from wastewater. The characterisation of biochar is carried out by scanning electron microscope (SEM) and Fourier transform infrared (FTIR). The impacts of the solution pH, adsorbent dosage, initial dye concentration, and temperature were investigated using a variety of models (RSM, ANN, kNN, and ANFIS). The statistical analysis of errors was conducted, resulting in a maximum removal effectiveness of 97.46% under optimised settings. These conditions included an adsorbent dose of 0.4 mg, a pH of 5, a CV concentration of 40.1 mg/L, and a temperature of 20 °C. The ANN, RSM, kNN, and ANFIS models all achieved R2 0.9685, 0.9618, 0.9421, and 0.8823, respectively. Even though all models showed accuracy in predicting the removal of CV dye, it was observed that the ANN model exhibited greater accuracy compared to the other models.

Adsorption of Eosin B from Wastewater onto the Prepared Porous Anion Exchange Membrane

This research describes the fabrication of the porous trimethylamine (TMA)-grafted anion exchange membrane (AEM) over a phase inversion process. The synthesis of the generated AEM was verified using Fourier transform infrared (FTIR) spectroscopy. The fabricated porous AEM showed 240% water uptake (WR), 1.45 mg/g ion exchange capacity (IEC), and a 9.0% linear expansion ratio (LER) at 25 °C. It exhibited a porous structure and higher thermal stability. It was utilized to remove eosin B (EB) from wastewater via the process of adsorption. The adsorption capacity of EB increased with time and the starting concentration of EB while decreasing with temperature and the AEM dosage. Adsorption isotherm investigation results showed that EB adsorption onto the porous AEM followed the Langmuir isotherm because the value of correlation coefficient (R2 = 0.992) was close to unity. Because the correlation coefficient was close to one, it was determined through adsorption kinetic experiments that the adsorption of EB on the produced porous AEM was suitable for a pseudo-second-order model. Thermodynamic study about process of EB adsorption on the porous AEM revealed that there was an exothermic (ΔH° = -16.60 kJ/mol) and spontaneous process.

Heterogeneous MIL-88A on MIL-88B hybrid: A promising eco-friendly hybrid from green synthesis to dual application (Adsorption and photocatalysis) in tetracycline and dyes removal

Herein, the green synthesis of heterogeneous dual functional MIL88A-on-MIL88B hybrids (MIL: Materials InstituteLavoisier) with different amounts of MIL88B compared to MIL88A, including 1:2, 1:1, and 2:1, has been carried out. The photocatalytic degradation of tetracycline and adsorption of tetracycline and dyes (Direct Red 80, Direct Red 23, Acid Blue 92, and Reactive Orange 14) were investigated. Although the ratio of MIL88A-on-MIL88B (1:1) hybrid displayed the best activity, there is a slight difference in the photocatalytic performance of the other mass ratios studied. The result revealed that after 70 min of forming MIL88A on MIL88B, the best pollutant removal performance is obtained. During the limited synthesis time, the lopsided growth of MIL88A on the MIL88B surface limits the formation of sufficient functional groups and new pores between MIL88B as the substrate and MIL88A, which are effective and decisive in the performance. In the photocatalytic studies, the synthesized composite had good compatibility with the zero-order kinetics, and hydroxyl radicals were recognized as the most active species in the photocatalytic reaction. In the adsorption process, the MIL88A-on-MIL88A composite followed pseudo-second-order kinetics and the Langmuir isotherm. Besides, mechanisms such as π-π interaction/stacking, hydrogen bonding, and π-metal interaction were proposed for the pollutant adsorption process.

Enhanced Photocatalysis of Electrically Polarized Titania Nanosheets

Titania (TiO2) nanosheets are crystals with controlled, highly ordered structures that improve the functionality of conventional TiO2 nanoparticles. Various surface modification methods have been studied to enhance the effectiveness of these materials as photocatalysts. Surface modifications using electrical polarization have attracted considerable attention in recent years because they can improve the function of titania without changing its composition. However, the combination of facet engineering and electrical polarization has not been shown to improve the functionality of TiO2 nanosheets. In the present study, the dye-degradation performance of polarized TiO2 nanosheets was evaluated. TiO2 nanosheets with a F/Ti ratio of 0.3 were synthesized via a hydrothermal method. The crystal morphology and structure were evaluated using transmission electron microscopy and X-ray diffraction. Then, electrical polarization was performed under a DC electric field of 300 V at 300 °C. The polarized material was evaluated using thermally stimulated current measurements. A dye-degradation assay was performed using a methylene blue solution under ultraviolet irradiation. The polarized TiO2 nanosheets exhibited a dense surface charge and accelerated decolorization. These results indicate that electrical polarization can be used to enhance the photocatalytic activity of TiO2.

Ionic Hyperbranched Poly(amido-amine)-Incorporated Nanofiltration Membranes for High-Efficiency Dye Desalination

High-efficiency dye desalination is crucial in the textile industry, considering its importance for human health, safe aquatic ecological systems, and resource recovery. In order to solve the problem of effective separation of univalent salt and ionic dye under the condition of high salt, ionic hyperbranched poly(amido-amine) (HBPs) were synthesized based on a simple and scalable one-step polycondensation method and then incorporated into the polyamide (PA) selective layers to construct charged nanochannels through interfacial polymerization (IP) on the surface of a polyvinyl chloride ultrafiltration (PVC-UF) hollow fiber membrane. Both the internal nanopores of HBPs (internal nanochannels) and the interfacial voids between HBPs and the PA matrix (external nanochannels) can be regarded as a fast water molecule transport pathway, while the terminal ionic groups of ionic HBPs endow the nanochannels with charge characteristics for improving ionic dye/salt selectivities. The permeate fluxes and dye/salt selectivities of HBP-TAC/PIP (57.3 L m-2 h-1 and rhodamine B (RB)/NaCl selectivity of 224.0) and HBP-PS/PIP (63.7 L m-2 h-1 and lemon yellow (LY)/NaCl selectivity of 664.0) membranes under 0.4 MPa operation pressure are much higher than PIP-only and HBP-NH2/PIP membranes. At the same time, this project also studied the membrane desalination process in a simulated high-salinity dye/salt mixture system to provide a theoretical basis and technical support for the actual dye desalination process.

Preparation and dye adsorption properties of activated carbon/clay/sodium alginate composite hydrogel membranes

A hydrogel membrane was prepared using activated carbon and sodium dodecyl sulphate modified montmorillonite clay incorporated into sodium alginate polymer. The activated carbon was prepared from a locally available susbine plant. The physiochemical characteristics of the synthesized hydrogel membrane were investigated using FTIR, SEM, EDX, and TGA techniques. The performance of the membrane was evaluated as an adsorbent by methyl red adsorption from water. The adsorption behavior of the hydrogel membrane was investigated under varying conditions of pH (2-10), membrane dose (0.0025-0.015 mg g-1), equilibrium adsorption time (30-360 minutes), solution temperature (25-45 °C) and dye concentration (100-500 mg L-1). The maximum adsorption capacity of the hydrogel membrane was 248.13 mg g-1. The kinetics of methyl red adsorption on hydrogel membrane best followed the pseudo-second order (PSO). The equilibrium adsorption results suggested that it obeyed the Freundlich isotherm very closely (R2 = 0.994). The thermodynamics of methyl red adsorption on the hydrogel membrane revealed that the adsorption was spontaneous (ΔS° = 16.15 kJ K-1 mol-1), favorable (ΔG° = -3.51 kJ mol-1), and endothermic (ΔH° = -1.48 kJ mol-1) in nature. These investigations suggested that the fabricated hydrogel membrane could be suitably used for methyl red adsorption from the solution.

Application of carbon-based adsorbents in the remediation of micro- and nanoplastics

Micro-nano plastics (MNPs) are emerging contaminants that can easily enter the food chain, posing risks to both the aquatic ecosystem and human health. Various physical, biological, and chemical methods have been explored to remove MNPs from water, and recently, adsorption technology has gained attention as an effective approach. Among the potential candidates, carbon-based adsorbent has emerged as a promising choice due to their low cost, eco-friendly nature, and sustainability. This paper summarizes recent advancements in MNP removal using carbon-based adsorbents, with a focus on the modification methods and adsorption mechanisms. Additionally, the factors influencing the adsorption performance and the methods for characterizing the adsorption mechanism are analyzed. Finally, the advantages and disadvantages of carbon-based adsorbents over other adsorbents are discussed, along with the current state of sustainable recycling and future research prospects.

Hybrid magnetic CoFe2O4@γ-Fe2O3@CTAB nanocomposites as efficient and reusable adsorbents for Remazol Brilliant Blue R dye

The main goal of the present survey was to elaborate, characterize and evaluate the efficiency of ferrite-based nanoparticles modified with cetyltrimethylammonium bromide (CTAB) as potential magnetic nanoadsorbents to remove Remazol Brilliant Blue R (RBBR) from water. It is proposed an innovative nanomaterial architecture based on highly magnetic and chemically stable core@shell nanoparticles covered by an adsorptive surface layer of CTAB (CoFe2O4@γ-Fe2O3@CTAB). Samples of two different mean sizes (7.5 and 14.6 nm) were synthesized using a hydrothermal coprecipitation followed by surface treatment and functionalization. Batch tests were performed to evaluate the influence of contact time, temperature, pH, shaking rate, presence of interferents and mean size on the performance of the proposed nanomaterials. The kinetics of the adsorption process followed the pseudo-second-order model with an equilibrium time of 20 min. The adsorption capacity was estimated by the Langmuir isotherm model and was found to be 56.3 mg/g (smaller size) and 45.6 mg/g (larger size) at pH = 3 and a shaking rate of 400 rpm. The process was spontaneous, exothermic, and showed increased randomness. Sulphate ions negatively impacted the removal of RBBR. The best performance of the nanoadsorbent based on smaller mean sizes can be correlated to its larger surface area. Regeneration and readsorption tests showed that the nanoadsorbents retain more than 80% of their original removal capacity, therefore they can be effectively recycled and reused.

Synthesis and characterizations of super adsorbent hydrogel based on biopolymer, Guar Gum-grafted-Poly (hydroxyethyl methacrylate) (Gg-g-Poly (HEMA)) for the removal of Bismarck brown Y dye from aqueous solution

Chemical modification of guar gum was done by graft copolymerization of monomer hydroxyethyl methacrylate (HEMA) using azobisisobutyronitrile (AIBN) as initiator. Optimal reaction parameters were settled by varying one reaction condition and keeping the other constant. The optimum reaction conditions worked out were solvent system: binary, [H2O] = 15.00 mL, [acetone] = 5.00 mL, [HEMA] = 82.217× 10-2 mol/L, [AIBN] = 3.333 × 10-2 mol/L, reaction time = 3 h, reaction temperature = 60 °C on to 1.00 g guar gum with Pg = 1694.6 and %GE = 68,704.152. Pure guar gum polymer and grafts were analyzed by several physicochemical investigation techniques like FTIR, SEM, XRD, EDX, and swelling studies. Percent swelling of the guar gum polymer and grafts was investigated at pH 2.2, 7.0, 7.4 and 9.4 concerning time. The finest yield of Ps was recorded at pH 9.4 with time 24 h for graft copolymer. Guar gum and grafted samples were explored for the sorption of toxic dye Bismarck brown Y from the aqueous solution with respect to variable contact time, pH, temperature and dye concentration so as to investigate the stimuli responsive sorption behaviour. Graft copolymers showed better results than guar gum with percent dye uptake (Du) of 97.588 % in 24 h contact time, 35 °C temperature, 9.4 pH at 150.00 ppm dye feed concentration as compared to Guar gum which only showed 85.260 % dye uptake at alike dye fed concentration. The kinetic behaviour of the polymeric samples was evaluated by applying many adsorption isotherms and kinetic models. The value of 1/n was between 0 → 1 showing that there was physisorption of the BB dye that took place on the surface of the polymers. Thermodynamics of BB Y adsorption onto hydrogels was investigated concerning the Van't Hoff equation. -∆G° values obtained from the curve proved the spontanity of the process. Within the context of adsorption efficiency, an investigation was conducted to examine the process of sorption of Bismarck brown Y dye from aqueous solutions. The graft copolymers demonstrated remarkable adsorption abilities, achieving a dye uptake (Du) of 97.588 % over a 24-h period at a temperature of 35 °C, pH level of 9.4, and a dye concentration of 150.00 ppm. The raised adsorption capacity was additionally corroborated by the application of several adsorption isotherms and kinetic models, which indicated that physisorption is the prevailing process/mechanism. Additionally, the thermodynamic research, utilising the Van't Hoff equation, validated the spontaneity of the adsorption phenomenon, as evidenced by the presence of a negative ∆G° values. The thermodynamic analysis revealed herein establishes a strong scientific foundation for the effectiveness of adsorbent composed of graft copolymers based on guar gum. The research conclude the efficiency of the guar gum based grafted copolymers for the water remediation as efficient adsorbents. The captured dye can be re-utilised and the hydrogels can be used for the same purpose in number of cycles.