The Comparison of the Multi-Layer Artificial Neural Network Training Methods in Terms of the Predictive Quality of the Coefficient of Friction of 1.0338 (DC04) Steel Sheet

Friction is one of the main phenomena accompanying sheet metal forming methods, affecting the surface quality of products and the formability of the sheet metal. The most basic and cheapest way to reduce friction is to use lubricants, which should ensure the highest lubrication efficiency and at the same time be environmentally friendly. Due to the trend towards sustainable production, vegetable oils have been used in research as an alternative to petroleum-based lubricants. The analysis of friction in sheet metal forming requires an appropriate tribotester simulating the friction conditions in a specific area of the sheet metal being formed. Research has used a special strip drawing tribometer, enabling the determination the value of the coefficient of friction in the blankholder zone in the deep drawing process. Quantitative analysis of the friction phenomenon is necessary at the stage of designing the technological process and selecting technological parameters, including blankholder pressure. This article presents the results of friction testing of 1.0338 (DC04) steel sheets using a strip drawing test. The experimental tests involved pulling a strip of sheet metal between two countersamples with a rounded surface. The tests were carried out on countersamples with different levels of roughness for the range of contact pressures occurring in the blankholder zone in the deep drawing process (1.7-5 MPa). The values of the coefficient of friction determined under dry friction conditions were compared with the results for edible (corn, sunflower and rapeseed) and non-edible (Moringa, Karanja) vegetable lubricants. The tested oils are the most commonly used vegetable-based biolubricants in metal forming operations. Multi-layer artificial neural networks were used to determine the relationship between the value of the contact pressure, the roughness of the countersamples, the oil viscosity and density, and the value of the coefficient of friction. Rapeseed oil provided the best lubrication efficiency during friction testing for all of the tested samples, with an average surface roughness of Sa 0.44-1.34 μm. At the same time, as the roughness of the countersamples increased, a decrease in lubrication efficiency was observed. The lowest root mean squared error value was observed for the MLP-4-8-1 network trained with the quasi-Newton algorithm. Most of the analysed networks with different architectures trained using the various algorithms showed that the kinematic viscosity of the oil was the most important aspect in assessing the friction of the sheets tested. The influence of kinematic viscosity on the value of the coefficient of friction is strongly dependent on the surface roughness of the countersamples.

Effect of Recycling on the Mechanical Properties of 6000 Series Aluminum-Alloy Sheet

Sustainability is one of the biggest values of today and for the future of our society; a responsible usage of material in every sector is fundamental to achieving sustainability goals. Aluminum alloys are some of the most promising materials in terms of strength and weight, but their production implies the emission of a high amount of CO2. For that reason, the study and development of aluminum alloys with increasing scrap content play a central role in future applications. In the current study, two sheet-aluminum 6181 alloys with different scrap content were analyzed and compared with a 6181 alloy coming from primary production. The alloys were compared in terms of chemical composition, microstructure, tensile properties, and forming behaviors. The results showed that the alloys coming from secondary productions contained a higher amount of manganese, iron, and copper. The metallurgical and mechanical behaviors were very similar to those of the primary produced alloy. Nevertheless, a drop in formability was shown in the aluminum alloys containing a high scrap amount when stressed in a biaxial condition. The study demonstrated the viability of 6181 alloy production using a high scrap amount, highlighting the main difference with the same alloy coming from primary route production.

Assessing Formability and Failure of UHMWPE Sheets through SPIF: A Case Study in Medical Applications

This work presents a comprehensive investigation of an experimental study conducted on ultra-high molecular weight polyethylene (UHMWPE) sheets using single point incremental forming (SPIF). The analysis is performed within a previously established research framework to evaluate formability and failure characteristics, including necking and fracture, in both conventional Nakajima tests and incremental sheet forming specimens. The experimental design of the SPIF tests incorporates process parameters such as spindle speed and step down to assess their impact on the formability of the material and the corresponding failure modes. The results indicate that a higher step down value has a positive effect on formability in the SPIF context. The study has identified the tool trajectory in SPIF as the primary influencing factor in the twisting failure mode. Implementing a bidirectional tool trajectory effectively reduced instances of twisting. Additionally, this work explores a medical case study that examines the manufacturing of a polyethylene liner device for a total hip replacement. This investigation critically analyses the manufacturing of plastic liner using SPIF, focusing on its formability and the elastic recovery exhibited by the material.

The Effect of Nozzle Temperature on the Low-Temperature Printing Performance of Low-Viscosity Food Ink

Low-temperature food printing technology is used in many fields, such as personalized nutrition, cooking art, food design and medical nutrition. By precisely controlling the deposition temperature of the ink, a food with a finer and more controllable structure can be produced. This paper investigates the influence of nozzle temperature on printing performance via a numerical simulation and experimental research. The results indicate that the ink gradually changed from a granular state to a fLow-characteristic deposition structure when the nozzle temperature increased from 19 °C to 27 °C. When the nozzle temperature exceeded 21 °C, the ink demonstrated excellent extrusion behavior and tended to flow. The widths of the rectangular frame deposition showed no obvious changes and were 4.07 mm, 4.05 mm and 4.20 mm, respectively. The extrusion behavior of the ink showed a structural mutation in the temperature range of 19-21 °C. Its line width changed from 3.15 mm to 3.73 mm, and its deposition structure changed from a grainy shape to a normal shape. Under the influence of different environmental control capabilities, bulk structure deposition demonstrates an ideal printing performance at 21, 23 and 25 °C, and the latter temperature is more suitable in the case of large external interference. The ink flowed violently when the nozzle temperature reached 27 °C, at which point the deposit structure flowed and deformed seriously. On the other hand, evaporation losses had a strong effect on Low-viscosity ink. To reach the full potential of this promising technology, it is necessary to determine the effect of nozzle temperature on printing performance. This article provides a method for developing and applying Low-viscosity, Low-temperature food printing.

On the Competition between Intergranular and Transgranular Failure within 7xxx Al Alloys with Tailored Microstructures

7xxx aluminium series reach exceptional strength compared to other industrial aluminium alloys. However, 7xxx aluminium series usually exhibit Precipitate-Free Zones (PFZs) along grain boundaries, which favour intergranular fracture and low ductility. In this study, the competition between intergranular and transgranular fracture is experimentally investigated in the 7075 Al alloy. This is of critical importance since it directly affects the formability and crashworthiness of thin Al sheets. Using Friction Stir Processing (FSP), microstructures with similar hardening precipitates and PFZs, but with very different grain structures and intermetallic (IM) particle size distribution, were generated and studied. Experimental results showed that the effect of microstructure on the failure mode was significantly different for tensile ductility compared to bending formability. While the tensile ductility was significantly improved for the microstructure with equiaxed grains and smaller IM particles (compared to elongated grains and larger particles), the opposite trend was observed in terms of formability.

Study on Press Formability and Properties of UV-Curable Polyurethane Acrylate Coatings with Different Reactive Diluents

UV-curable coatings have numerous advantages, including environmental sustainability due to 100% solid content, economic feasibility attributable to relatively fast curing time, decent appearance, mechanical properties, chemical resistance, and abrasion resistance. However, UV-curable polyurethane acrylate coatings on metals apparently restrict their engineering applications owing to low mechanical properties and poor thermal stability, giving UV-curable coatings less flexibility and formability. In this study, we evaluated the property change of films according to the type of reactive diluents that lowers the viscosity of UV-curing coatings for pre-coated metal and has a substantial effect on the curing rate, viscoelastic properties, adhesive properties, and flexibility of the film. Moreover, there are many changes in the properties of coatings according to varied curing conditions in order to evaluate the oxygen inhibition phenomenon during the curing process in the atmosphere. In particular, to evaluate the effect of reactive diluents on forming formability, which is the most crucial property for the pre-coated metal, this study used conventional formability tests, such as t-bending or the Erichsen test. Moreover, a cross-die cup drawing mold with a similar form as failure and Safety Zone was utilized in order to obtain clearer information on its actual formability. The analysis on the effect of failure and safety zone on the material used in press forming was conducted by assessing limit punch height and forming a limit diagram of the manufactured film according to varied reactive diluents.

Effect of Hot Metal Gas Forming Process on Formability and Microstructure of 6063 Aluminum Alloy Double Wave Tube

The hot metal gas forming process can significantly improve the formability of a tube and is suitable for the manufacturing of parts with complex shapes. In this paper, a double wave tube component is studied. The effects of different temperatures (400 °C, 425 °C, 450 °C and 475 °C) and different pressures (1 MPa, 1.5 MPa, 2 MPa, 2.5 MPa and 3 MPa) on the formability of 6063 aluminum alloy tubes were studied. The influence of hot metal gas forming process parameters on the microstructure was analyzed. The optimal hot metal gas forming process parameters of 6063 aluminum alloy tubes were explored. The results show that the expansion rate increases with the increase in pressure. The pressure affects the deformation of the tube, which in turn has an effect on the dynamic softening of the material. The expansion rate of parts also increases with the increase in forming temperature. The increased deformation temperature is beneficial to the dynamic recrystallization of 6063, resulting in softening of the material and enhanced deformation uniformity between grains, so that the formability of the material is improved. The optimum hot metal gas forming process parameters of 6063 aluminum alloy tubes are the temperature of 475 °C and the pressure of 2.5 MPa; the maximum expansion ratio is 41.6%.

A Review of Characterization and Modelling Approaches for Sheet Metal Forming of Lightweight Metallic Materials

Lightweight sheet metals are attractive for aerospace and automotive applications due to their exceptional properties, such as low density and high strength. Sheet metal forming (SMF) is a key technology to manufacturing lightweight thin-walled complex-shaped components. With the development of SMF, numerical simulation and theoretical modelling are promoted to enhance the performance of new SMF technologies. Thus, it is extraordinarily valuable to present a comprehensive review of historical development in SMF followed by state-of-the-art advanced characterization and modelling approaches for lightweight metallic materials. First, the importance of lightweight materials and their relationship with SMF followed by the historical development of SMF are reviewed. Then, the progress of advanced finite element technologies for simulating metal forming with lightweight alloys is covered. The constitutive modelling of lightweight alloys with an explanation of state-of-the-art advanced characterization to identify the constitutive parameters are presented. Then, the formability of sheet metals with major influencing factors, the techniques for measuring surface strains in SMF and the experimental and modelling approaches for determining the formability limits are clarified. Finally, the review is concluded by affording discussion of the present and future trends which may be used in SMF for lightweight metallic materials.

Evaluation of Powder Metallurgy Workpiece Prepared by Equal Channel Angular Rolling

The aim of the article is to examine the workability of sintered powder material of aluminum alloy (Alumix 321) through severe plastic deformations under the conditions of the equal channel angular rolling (ECAR) process. Accordingly, the stress-strain analysis of the ECAR was carried out through a computer simulation using the finite element method (FEM) by Deform 3D software. Additionally, the formability of the ALUMIX 321 was investigated using the diametrical compression (DC) test, which was measured and analyzed by digital image correlation and finite element simulation. The relationship between failure mode and stress state in the ECAR process and the DC test was quantified using stress triaxiality and Lode angle parameter. It is concluded that the sintered powder material during the ECAR processing failure by a shearing fracture because in the fracture location the stress conditions were close to the pure shear (η and θ¯ ≈ 0). Moreover, the DC test revealed the potential role as the method of calibration of the fracture locus for stress conditions between the pure shear and the axial symmetry compression.

On the Formability of Medium Mn Steel Treated with Varied Thermal Processing Routes

In this contribution, we investigate the influence of thermal processing routes on the formability of medium Mn steel by assessing the strain hardening coefficient and anisotropy factor using the uniaxial tensile test. Medium Mn steel processed by intercritical annealing (IA) at 680 °C for 4 h demonstrates better formability than steel treated with a combination of IA at 800 °C for 10 min and quenching and partitioning (Q&P), based on the much higher strain hardening coefficient (n) and comparable anisotropy factor (r, r_m, ∆r). The higher strain hardening coefficient of medium Mn steel with single IA treatment is ascribed to the enhanced transformation-induced plasticity (TRIP) effect resulting from the large amount of austenite that is transformed into martensite during deformation. In addition, the IA process allows for the production of medium Mn steel with high ductility, which is beneficial for its high formability and good 'part ductility' in lightweight automotive applications.

Experimental Investigation on the Formability of Al-Mg Alloy 5052 Sheet by Tensile and Cupping Test

Aiming at the enhancement of the lightweight formability potential of aluminum alloy, the bulging and tensile properties of a 5052 Aluminum alloy sheet were tested on a microcomputer controlled sheet metal forming tester and tensile testing machine. The effects of different blank holder force, punch velocity and lubrication conditions were investigated on bulging properties by the experimental analysis. The cupping values (Erichsen Cupping Index: IE) of sheets with a thickness of 1.2 mm at room temperature were obtained under different process parameters. Meanwhile, the anisotropic property of the material was analyzed in different rolling directions. The results show that the sheet cupping values increase with the increase of blank holder force and punch velocity, and the stress state was changed due to the changing of the blank holder force and strain rate. Moreover, the use of lubricating conditions with a lower coefficient of friction allows the sheet to exhibit a larger cupping value. The effect of rolling direction on the anisotropy of 5052 aluminum alloy sheet is distinct, which means in the aluminum alloy sheet forming process the anisotropy factor should be carefully considered.

Effect of Copper Addition on the Formability of 304L Austenitic Stainless Steel

To improve the antibacterial properties of 304L austenitic stainless steel, copper is often added as an antibacterial agent, but the forming performance of the resulting material is poor, impacting its actual production and use. Therefore, this study investigated the influence of copper addition on the formability of 304L austenitic stainless steel with drawing, cupping and conical cup forming tests. Mechanical properties were determined with tensile and hardness tests. The microstructure and phase transformation were further characterized by metallographic microscopy, scanning electron microscopy and x-ray diffraction analysis. It was found that the addition of copper impaired the mechanical properties of 304L austenitic stainless steel, increased the stacking fault energy of the material and inhibited the occurrence of strain-induced martensite transformation, leading to a decrease in the formability of 304L austenitic stainless steel.

Deformation Characteristics, Formability and Springback Control of Titanium Alloy Sheet at Room Temperature: A Review

Titanium alloy sheets present inferior formability and severe springback in conventional forming processes at room temperature which greatly restrict their applications in complex-shaped components. In this paper, deformation characteristics and formability and springback behaviors of titanium alloy sheet at room temperature are systematically reviewed. Firstly, deformation characteristics of titanium alloys at room temperature are discussed, and formability improvement under high-rate forming and other methods are summarized, especially the impacting hydroforming developed by us. Then, the main advances in springback prediction and control are outlined, including the advanced constitutive models as well as the optimization of processing paths and parameters. More importantly, notable springback reduction is observed with high strain rate forming methods. Finally, potential investigation prospects for the precise forming of titanium alloy sheet in the future are suggested.

Development of a Formability Prediction Model for Aluminium Sandwich Panels with Polymer Core

In the present work, the compatibility relationship on the failure criteria between aluminium and polymer was established, and a mechanics-based model for a three-layered sandwich panel was developed based on the M-K model to predict its Forming Limit Diagram (FLD). A case study for a sandwich panel consisting of face layers from AA5754 aluminium alloy and a core layer from polyvinylidene difluoride (PVDF) was subsequently conducted, suggesting that the loading path of aluminium was linear and independent of the punch radius, while the risk for failure of PVDF increased with a decreasing radius and an increasing strain ratio. Therefore, the developed formability model would be conducive to the safety evaluation on the plastic forming and critical failure of composite sandwich panels.

Constitutive Model Parameter Identification Based on Optimization Method and Formability Analysis for Ti6Al4V Alloy

Titanium alloy is widely applied in aerospace, medical, shipping and other fields due to its high specific strength and low density. The purpose of this study was to analyze the formability of Ti6Al4V alloys at elevated temperatures. An accurate constitutive model is the basic condition for accurately simulating the plastic forming of materials, and it is an important basis for optimizing the parameters of the hot forging forming process. In this study, the optimization algorithm was used to accurately identify the high-temperature constitutive model parameters of Ti6Al4V titanium alloy, and the hot working diagram was established to optimize the hot forming process parameters. The optimal forming conditions of Ti6Al4V titanium alloy are given. Ti6Al4V alloy was subjected to high-temperature compression tests at 800–1000 °C and at strain rates of 0.01–5 s⁻¹ on a Gleeble-1500D thermal/mechanical simulation machine. Each parameter of the Hansel–Spittel constitutive model was taken as an independent variable, and the accumulated error between the stress calculated by the constitutive model and the stress obtained by experimentation was used as an objective function. Based on response surface methodology, an inverse optimization method for identifying the parameters of the high-temperature constitutive model of Ti6Al4V alloy is proposed in this paper. An orthogonal test design was adopted to obtain sample point data, and a third-order response surface approximate model was established. The genetic algorithm (GA) was applied to reversely optimize the parameters of the constitutive model. To verify the accuracy of the optimized constitutive model, the average absolute relative error (AARE) and correlation coefficient (R) were used to evaluate the reliability of optimized constitutive model. The R value of the model was 0.999, and the AARE value was 0.048, respectively, indicating that the established high-temperature constitutive model for Ti6Al4V alloy has good calculation accuracy. The flow stress behavior of the material could be accurately delineated. Meanwhile, in order to study the formability of Ti6Al4V alloy, the hot processing map of the alloy, based on a dynamic material model, was established in this paper. The optimum hot working domains of the Ti6Al4V alloy were determined within 840–920 °C/0.01–0.049 s⁻¹ and 940–980 °C/0.11–1.65 s⁻¹; the hot processing map was verified in combination with the microstructure, and the fine and equiaxed grains and a large amount of β phase could be found at 850 °C/0.01 s⁻¹.

Mechanical Behavior of Multi-Phase Steels Comprising Retained Austenite

The retained austenite (RA) in advanced high-strength steel (AHSS) grades, such as dual-phase (DP) steels, plays an important role on their formability. Thanks to the transformation-induced plasticity (TRIP) effect that occurs during the mechanically induced transformation of RA into martensite, additional ductility is obtained. Martensite has a higher flow stress than austenite; hence, the transformation results in an apparent hardening, which is beneficial for the stability of deformation. The stability of RA at a given temperature strongly depends on its carbon content, which, in AHSS, is not uniform but distributed. The aim of this study is to build a model that predicts the transformation as well as TRIP in a DP steel grade with RA. A physics-based kinetic model is presented that captures the transformation of retained austenite based on the thermodynamic driving force of the applied stress. A direct analytical estimate of transformation plasticity is provided, which is consistent with the kinetic model. Transformation kinetics is incorporated in a self-consistent, mean-field homogenization-based constitutive model. Finally, an indication of the effect of transformation of retained austenite on formability is given.

Effect of Carbon Content on Microstructure, Properties and Texture of Ultra-Thin Hot Rolled Strip Produced by Endless Roll Technology

In order to make a comprehensive comparison between ultra-thin hot rolled low carbon steel (LC) and extra low carbon steel (ELC) produced by endless roll technology and explain the differences, a detailed investigation into the microstructural characterization, characteristics of cementite and precipitates, mechanical properties, internal friction peaks, texture characterization by an X-ray powder diffractometer and electron backscatter diffraction, and formability including earing behavior, hole expanding ratio and V-shaped bending properties was carried out with different carbon content for 1.0 mm thickness ultra-thin hot rolled strip produced in endless strip production line. The experimental results indicate that the microstructure of both is composed of multi-layer areas with different grain sizes and thicknesses, the strength and elongation of LC are higher than that of ELC, but the content of solid solution carbon atoms and r of ELC are higher than that of LC, at the same time, the formability of ultra-thin strip ELC is better than that of LC mainly related to the content of {hkl} <110> and {111} <112> of ELC was higher than those of LC. The mechanical and formability properties of ultra-thin hot rolled strip by endless roll technology can meet the requirements of replacement cold rolled strip by hot rolled strip.

The Synergistic Effect of Temperature and Loading Rate on Deformation for Thermoplastic Fiber Metal Laminates

The glass fiber reinforced polypropylene/AA2024 hybrid laminates (short for Al/Gf/PP laminates) as structural materials were prepared and formed by hot pressing. The synergistic effects of temperature and loading speed on the laminate deformation under tensile and bending conditions were investigated and analyzed in this study. In tension, stress–strain curves presented bimodal types effected by tensile rates and temperatures. The state of PP resin determines the mechanical behavior of the FMLs. The tensile rate has no effect on FML deformation without heating or over the melting point of PP resin (about 170 °C). The softening point of PP resin (about 100 °C) is characteristic temperature. When the temperature exceeds the softening point but does not reach the melting point, the tensile strength and elongation will demonstrate coordinated growth at a relatively high tensile speed. The efficiency of fiber bridging is affected significantly since the resin is the medium that transfers load from the metal to the fiber. Under bending, the curves presented a waterfall decrement with temperature increment. The softening point of resin matrix is the key in a bending process. When the temperature is near the softening point, deformation is sensitive to both the temperature and the loading speed to a certain extent. If temperature is lower than softening point, deformation is mainly guided by temperature. If the temperature is beyond the softening point, loading speed is in a leading position of deformation. The bending strength gradually increases with loading rate. By using these deformation characteristics, the deformation of the thermoplastic laminates can be controlled in stamping or other plastic forming processes for thermoplastic fiber metal laminates.

Effect of Tool Geometry Parameters on the Formability of a Camera Cover in the Deep Drawing Process

The formability of the drawn part in the deep drawing process depends not only on the material properties, but also on the equipment used, metal flow control and tool parameters. The most common defects can be the thickening, stretching and splitting. However, the optimization of tools including the die and punch parameters leads to a reduction of the defects and improves the quality of the products. In this paper, the formability of the camera cover by aluminum alloy A1050 in the deep drawing process was examined relating to the tool geometry parameters based on numerical and experimental analyses. The results showed that the thickness was the smallest and the stress was the highest at one of the bottom corners where the biaxial stretching was the predominant mode of deformation. The problems of the thickening at the flange area, the stretching at the side wall and the splitting at the bottom corners could be prevented when the tool parameters were optimized that related to the thickness and stress. It was clear that the optimal thickness distribution of the camera cover was obtained by the design of tools with the best values—with the die edge radius 10 times, the pocket radius on the bottom of the die 5 times, and the punch nose radius 2.5 times the sheet thickness. Additionally, the quality of the camera cover was improved with a maximum thinning of 25% experimentally, and it was within the suggested maximum allowable thickness reduction of 45% for various industrial applications after optimizing the tool geometry parameters in the deep drawing process.

The Effect of Direct Electric Current on the Plastic Behavior of AA7075 Aluminum Alloy in Different States of Hardening

Electrically-Assisted Forming (EAF) techniques are interesting and promising for the automotive industry. Electrically-assisted tensile tests were carried out on specimens of AA7075 aluminum alloy in different states of hardening, namely T6 (the as-received state) and the supersaturated solid solution state. All the tests were carried out in quasi-static conditions under the application of direct electric current (DC) in the range of 90 to 540 A. The experimental results showed that with a DC density of 10 A/mm² the uniform strain and strain at fracture increased when the AA7075 was in the supersaturated solid solution state. A correlation between the mechanical results and microstructural features analysed through transmission electron microscopy was assessed. An explanation of the investigated phenomena based on the electron wind theory, heterogeneous microscale Joule heating and the Portevin–Le Chatelier (PLC) effect was finally proposed.

Plasticity and Formability of Annealed, Commercially-Pure Aluminum: Experiments and Modeling

The plasticity and formability of a commercially-pure aluminum sheet (AA1100-O) is assessed by experiments and analyses. Plastic anisotropy of this material is characterized by uniaxial and plane-strain tension along with disk compression experiments, and is found to be non-negligible (e.g., the r-values vary between 0.445 and 1.18). On the other hand, the strain-rate sensitivity of the material is negligible at quasistatic rates. These results are used to calibrate constitutive models, i.e., the Yld2000-2d anisotropic yield criterion as the plastic potential and the Voce isotropic hardening law. Marciniak-type experiments on a fully-instrumented hydraulic press are performed to determine the Forming Limit Curve of this material. Stereo-type Digital Image Correlation is used, which confirms the proportional strain paths induced during stretching. From these experiments, limit strains, i.e., the onset of necking, are determined by the method proposed by ISO, as well as two methods based on the second derivative. To identify the exact instant of necking, a criterion based on a statistical analysis of the noise that the strain signals have during uniform deformation versus the systematic deviations that necking induces is proposed. Finite element simulation for the Marciniak-type experiment is conducted and the results show good agreement with the experiment.

Novel Approach and Interpretation for the Determination of Electromagnetic Forming Limits

A new method to determine electromagnetic forming limits curves (EM-FLCs) for sheet metals is proposed. The different strain paths (between uniaxial and biaxial tension) are achieved by specific tool coil and specimen designs. It is ensured that the apex of the specimen deforms on a constant strain path, and excess bending at the apex is avoided. This is done so that the determined EM-FLCs are comparable to their quasi-static counterparts. The method determines the EM-FLCs for the aluminum alloys AA-1050a-H24 and EN AW-5083-H111 and the magnesium alloy Mg AZ31-O. Overall, it is observed that the necking limits in electromagnetic forming (EMF) are higher compared to quasi-static forming. The fracture surfaces of electromagnetically deformed specimens are examined to reveal the existence of out-of-plane shear stresses. A numerical analysis corroborates this observation and their variation with strain rate. The presence of such stresses is proposed as a possible reason for the increased necking limits in EMF. As reasons for higher forming limits, previous research has identified inertial stabilization, strain rate hardening, die impact, and change in deformation mechanism. The current study reaffirms the positive effect of inertial stabilization and makes key observations in the increase of twinning in EMF of Mg AZ31-O.

Effects of Process Parameters on the Thickness Uniformity in Two-Point Incremental Forming (TPIF) with a Positive Die for an Irregular Stepped Part

Incremental sheet forming (ISF) is a novel flexible forming technology with advantages, such as a low forming force, low-energy-consuming equipment, and good forming performance. The lack of available information about the formability of the two-point incremental forming (TPIF) process makes it limited for practical applications. Taking an irregular stepped part as the target part, the effects of process parameters on the thickness uniformity when using TPIF with a positive die for AA1060 aluminum alloy sheets were investigated. First, the set of optimal parameters regarding the diameter of the tool head, feed rate, and the step size were obtained through orthogonal experiments. Furthermore, the optimal parameter set of the number of forming passes, the direction of movement of the forming tool, and the forming angle was determined and the optimal forming result was numerically and experimentally verified. This demonstrated that the parameters affecting the thickness uniformity of the irregular stepped parts were, in descending order, the diameter of the forming tool, the feed rate, and the step size, with corresponding optimal values of 12 mm, 15,000 mm/min, and 0.4 mm, respectively. With an increase of the number of passes and a decrease of the forming angle between adjacent passes, and adopting an alternating clockwise and counterclockwise toolpath, the thickness uniformity of the formed parts was effectively improved.

A Further Improvement in the Room-Temperature Formability of Magnesium Alloy Sheets by Pre-Stretching

Pre-stretching experiments were carried out on AZ31-0.5Ca magnesium alloy to alter the microstructure and texture for enhancing room-temperature formability. Compared to as-received alloy, the formability of a 5%-stretched sample was improved by 15%. This was attributed to enhanced strain hardening capability related to the weakening of basal texture and less homogeneous microstructure. In addition, in-grain misorientation axis analysis performed on the samples (as-received and stretched) also confirmed the higher activity of the non-basal slip systems in the 5%-stretched sample.

Formability of Ultrasonically Additive Manufactured Ti-Al Thin Foil Laminates

This study investigates the effect of strain rates and temperatures on the mechanical behavior of ultrasonically consolidated Titanium–Aluminum thin foils to understand and characterize their formability. To this goal, laminated composite samples with a distinct number of layers were bonded using ultrasonic consolidation. Then, tensile and biaxial hydraulic bulge tests at different strain rates and temperature conditions were conducted. The effect of the sample orientation on the mechanical response was also examined. Tensile and hydraulic bulge tests results were compared to observe differences in ultimate tensile strength and strain levels under uniaxial and biaxial loading conditions. The effects of loading condition, strain rate, and temperature on the material response were analyzed and discussed on the basis of test results. In general, it was concluded that the maximum elongation values attained were higher for the samples subtracted along the sonotrode movement direction compared to those obtained from the normal to sonotrode movement direction. The elongation was obtained as high as 46% for seven bi-layered samples at high-temperature ranges of 200–300 °C. Hydraulic bulge test results showed that elongation improved as the number of bi-layers increased, yet the ultimate strength values did not change significantly indicating an expansion of the formability window.

Formability and Failure Mechanisms of Woven CF/PEEK Composite Sheet in Solid-State Thermoforming

In this study, the formability of woven carbon-fiber (CF)-reinforced polyether-ether-ketone (PEEK) composite sheets in the solid-state thermoforming process were investigated, and the failure mechanisms were discussed. The formability of the woven CF/PEEK sheets were analyzed using flexural tests, Erichsen test, and microscopic observation. The results show that the formability of CF/PEEK sheets significantly increases as the temperature rises from 165 to 325 °C, and slightly decreases as the deformation speed rises from 2 to 120 mm/min. The deformation of the sheets is caused by plastic deformation, shear deformation and squeeze deformation, without plastic thinning and fiber slippage, which is due to the restriction of the solid matrix and locked fibers. Moreover, the wrinkles will cause fiber fracture at lower temperatures and delamination at higher temperatures. At higher temperatures, the wrinkles mainly occur at the position with [0°/90°] fibers due to the squeezing of the matrix and fibers.

Ultrasonic Vibration Facilitates the Micro-Formability of a Zr-Based Metallic Glass

Thermoplastic microforming not only breaks through the bottleneck in the manufacture of metallic glasses, but also offers alluring prospects in microengineering applications. The microformability of metallic glasses decreases with a reduction in the mold size owing to the interfacial size effect, which seriously hinders their large-scale applications. Here, ultrasonic vibration was introduced as an effective method to improve the microformability of metallic glasses, owing to its capabilities of improving the material flow and reducing the interfacial friction. The results reveal that the microformability of supercooled Zr₃₅Ti₃₀Cu_8.25Be_26.75 metallic glasses is conspicuously enhanced by comparison with those under quasi-static loading. The more intriguing finding is that the microformability of the Zr-based metallic glasses can be further improved by tuning the amplitude of the ultrasonic vibration. The physical origin of the above scenario is understood, in depth, on the basis of ultrasonic vibration-assisted material flow, as demonstrated by the finite element method.

On the High Formability of AZ31-0.5Ca Magnesium Alloy

In this work, we investigated the effect of Ca on the formability of the AZ31 Mg alloy. For this purpose, the microstructure, texture, mechanical properties and formability of AZ31 Mg alloy samples containing 0.5 wt. % Ca (AZ31-0.5Ca) were studied. For comparison, the performance of Ca-Free AZ31 alloy samples with similar grain size was also investigated. In addition, formability of this alloy was reached at a high punch speed. The results of this work showed that the addition of 0.5 wt. % Ca can enhance the formability of the AZ31 alloy, which was three times greater than that of the Ca-Free AZ31 alloy. The improved formability was attributed to the formation of (Mg,Al)₂Ca particles (~1 μm), which, in turn, contribute to reducing the intensity of the strong basal texture during the primary processing of the alloy. The in-grain misorientation axis analysis determined by electron back-scattered diffraction and critical resolved shear stress calculations carried out by the viscoplastic self-consistent model showed that the non-basal slip systems could be activated in the AZ31-0.5Ca alloy.

Improvement of the Mechanical Properties of 1022 Carbon Steel Coil by Using the Taguchi Method to Optimize Spheroidized Annealing Conditions

Cold forging is often applied in the fastener industry. Wires in coil form are used as semi-finished products for the production of billets. This process usually requires preliminarily drawing wire coil in order to reduce the diameter of products. The wire usually has to be annealed to improve its cold formability. The quality of spheroidizing annealed wire affects the forming quality of screws. In the fastener industry, most companies use a subcritical process for spheroidized annealing. Various parameters affect the spheroidized annealing quality of steel wire, such as the spheroidized annealing temperature, prolonged heating time, furnace cooling time and flow rate of nitrogen (protective atmosphere). The effects of the spheroidized annealing parameters affect the quality characteristics of steel wire, such as the tensile strength and hardness. A series of experimental tests on AISI 1022 low carbon steel wire are carried out and the Taguchi method is used to obtain optimum spheroidized annealing conditions to improve the mechanical properties of steel wires for cold forming. The results show that the spheroidized annealing temperature and prolonged heating time have the greatest effect on the mechanical properties of steel wires. A comparison between the results obtained using the optimum spheroidizing conditions and the measures using the original settings shows the new spheroidizing parameter settings effectively improve the performance measures over their value at the original settings. The results presented in this paper could be used as a reference for wire manufacturers.

Property Criteria for Automotive Al-Mg-Si Sheet Alloys

In this study, property criteria for automotive Al-Mg-Si sheet alloys are outlined and investigated in the context of commercial alloys AA6016, AA6005A, AA6063 and AA6013. The parameters crucial to predicting forming behavior were determined by tensile tests, bending tests, cross-die tests, hole-expansion tests and forming limit curve analysis in the pre-aged temper after various storage periods following sheet production. Roping tests were performed to evaluate surface quality, for the deployment of these alloys as an outer panel material. Strength in service was also tested after a simulated paint bake cycle of 20 min at 185 °C, and the corrosion behavior was analyzed. The study showed that forming behavior is strongly dependent on the type of alloy and that it is influenced by the storage period after sheet production. Alloy AA6016 achieves the highest surface quality, and pre-ageing of alloy AA6013 facilitates superior strength in service. Corrosion behavior is good in AA6005A, AA6063 and AA6016, and only AA6013 shows a strong susceptibility to intergranular corrosion. The results are discussed below with respect to the chemical composition, microstructure and texture of the Al-Mg-Si alloys studied, and decision-making criteria for appropriate automotive sheet alloys for specific applications are presented.